diff --git a/drivers/char/tpm/Kconfig b/drivers/char/tpm/Kconfig index a18c314da211..4308f9ca7a43 100644 --- a/drivers/char/tpm/Kconfig +++ b/drivers/char/tpm/Kconfig @@ -86,6 +86,16 @@ config TCG_TIS_SYNQUACER To compile this driver as a module, choose M here; the module will be called tpm_tis_synquacer. +config TCG_TIS_I2C_CR50 + tristate "TPM Interface Specification 2.0 Interface (I2C - CR50)" + depends on I2C + select TCG_CR50 + help + This is a driver for the Google cr50 I2C TPM interface which is a + custom microcontroller and requires a custom i2c protocol interface + to handle the limitations of the hardware. To compile this driver + as a module, choose M here; the module will be called tcg_tis_i2c_cr50. + config TCG_TIS_I2C_ATMEL tristate "TPM Interface Specification 1.2 Interface (I2C - Atmel)" depends on I2C diff --git a/drivers/char/tpm/Makefile b/drivers/char/tpm/Makefile index 84db4fb3a9c9..66d39ea6bd10 100644 --- a/drivers/char/tpm/Makefile +++ b/drivers/char/tpm/Makefile @@ -27,6 +27,8 @@ obj-$(CONFIG_TCG_TIS_SPI) += tpm_tis_spi.o tpm_tis_spi-y := tpm_tis_spi_main.o tpm_tis_spi-$(CONFIG_TCG_TIS_SPI_CR50) += tpm_tis_spi_cr50.o +obj-$(CONFIG_TCG_TIS_I2C_CR50) += tpm_tis_i2c_cr50.o + obj-$(CONFIG_TCG_TIS_I2C_ATMEL) += tpm_i2c_atmel.o obj-$(CONFIG_TCG_TIS_I2C_INFINEON) += tpm_i2c_infineon.o obj-$(CONFIG_TCG_TIS_I2C_NUVOTON) += tpm_i2c_nuvoton.o diff --git a/drivers/char/tpm/tpm_tis_i2c_cr50.c b/drivers/char/tpm/tpm_tis_i2c_cr50.c new file mode 100644 index 000000000000..ec9a65e7887d --- /dev/null +++ b/drivers/char/tpm/tpm_tis_i2c_cr50.c @@ -0,0 +1,790 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright 2020 Google Inc. + * + * Based on Infineon TPM driver by Peter Huewe. + * + * cr50 is a firmware for H1 secure modules that requires special + * handling for the I2C interface. + * + * - Use an interrupt for transaction status instead of hardcoded delays. + * - Must use write+wait+read read protocol. + * - All 4 bytes of status register must be read/written at once. + * - Burst count max is 63 bytes, and burst count behaves slightly differently + * than other I2C TPMs. + * - When reading from FIFO the full burstcnt must be read instead of just + * reading header and determining the remainder. + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include "tpm_tis_core.h" + +#define TPM_CR50_MAX_BUFSIZE 64 +#define TPM_CR50_TIMEOUT_SHORT_MS 2 /* Short timeout during transactions */ +#define TPM_CR50_TIMEOUT_NOIRQ_MS 20 /* Timeout for TPM ready without IRQ */ +#define TPM_CR50_I2C_DID_VID 0x00281ae0L /* Device and vendor ID reg value */ +#define TPM_CR50_I2C_MAX_RETRIES 3 /* Max retries due to I2C errors */ +#define TPM_CR50_I2C_RETRY_DELAY_LO 55 /* Min usecs between retries on I2C */ +#define TPM_CR50_I2C_RETRY_DELAY_HI 65 /* Max usecs between retries on I2C */ + +#define TPM_I2C_ACCESS(l) (0x0000 | ((l) << 4)) +#define TPM_I2C_STS(l) (0x0001 | ((l) << 4)) +#define TPM_I2C_DATA_FIFO(l) (0x0005 | ((l) << 4)) +#define TPM_I2C_DID_VID(l) (0x0006 | ((l) << 4)) + +/** + * struct tpm_i2c_cr50_priv_data - Driver private data. + * @irq: Irq number used for this chip. + * If irq <= 0, then a fixed timeout is used instead of waiting for irq. + * @tpm_ready: Struct used by irq handler to signal R/W readiness. + * @buf: Buffer used for i2c writes, with i2c address prepended to content. + * + * Private driver struct used by kernel threads and interrupt context. + */ +struct tpm_i2c_cr50_priv_data { + int irq; + struct completion tpm_ready; + u8 buf[TPM_CR50_MAX_BUFSIZE]; +}; + +/** + * tpm_cr50_i2c_int_handler() - cr50 interrupt handler. + * @dummy: Unused parameter. + * @tpm_info: TPM chip information. + * + * The cr50 interrupt handler signals waiting threads that the + * interrupt has been asserted. It does not do any interrupt triggered + * processing but is instead used to avoid fixed delays. + * + * Return: + * IRQ_HANDLED signifies irq was handled by this device. + */ +static irqreturn_t tpm_cr50_i2c_int_handler(int dummy, void *tpm_info) +{ + struct tpm_chip *chip = tpm_info; + struct tpm_i2c_cr50_priv_data *priv = dev_get_drvdata(&chip->dev); + + complete(&priv->tpm_ready); + + return IRQ_HANDLED; +} + +/** + * tpm_cr50_i2c_wait_tpm_ready() - Wait for tpm to signal ready. + * @chip: A TPM chip. + * + * Wait for completion interrupt if available, otherwise use a fixed + * delay for the TPM to be ready. + * + * Return: + * - 0: Success. + * - -errno: A POSIX error code. + */ +static int tpm_cr50_i2c_wait_tpm_ready(struct tpm_chip *chip) +{ + struct tpm_i2c_cr50_priv_data *priv = dev_get_drvdata(&chip->dev); + + /* Use a safe fixed delay if interrupt is not supported */ + if (priv->irq <= 0) { + msleep(TPM_CR50_TIMEOUT_NOIRQ_MS); + return 0; + } + + /* Wait for interrupt to indicate TPM is ready to respond */ + if (!wait_for_completion_timeout(&priv->tpm_ready, + msecs_to_jiffies(chip->timeout_a))) { + dev_warn(&chip->dev, "Timeout waiting for TPM ready\n"); + return -ETIMEDOUT; + } + + return 0; +} + +/** + * tpm_cr50_i2c_enable_tpm_irq() - Enable TPM irq. + * @chip: A TPM chip. + */ +static void tpm_cr50_i2c_enable_tpm_irq(struct tpm_chip *chip) +{ + struct tpm_i2c_cr50_priv_data *priv = dev_get_drvdata(&chip->dev); + + if (priv->irq > 0) { + reinit_completion(&priv->tpm_ready); + enable_irq(priv->irq); + } +} + +/** + * tpm_cr50_i2c_disable_tpm_irq() - Disable TPM irq. + * @chip: A TPM chip. + */ +static void tpm_cr50_i2c_disable_tpm_irq(struct tpm_chip *chip) +{ + struct tpm_i2c_cr50_priv_data *priv = dev_get_drvdata(&chip->dev); + + if (priv->irq > 0) + disable_irq(priv->irq); +} + +/** + * tpm_cr50_i2c_transfer_message() - Transfer a message over i2c. + * @dev: Device information. + * @adapter: I2C adapter. + * @msg: Message to transfer. + * + * Call unlocked i2c transfer routine with the provided parameters and + * retry in case of bus errors. + * + * Return: + * - 0: Success. + * - -errno: A POSIX error code. + */ +static int tpm_cr50_i2c_transfer_message(struct device *dev, + struct i2c_adapter *adapter, + struct i2c_msg *msg) +{ + unsigned int try; + int rc; + + for (try = 0; try < TPM_CR50_I2C_MAX_RETRIES; try++) { + rc = __i2c_transfer(adapter, msg, 1); + if (rc == 1) + return 0; /* Successfully transferred the message */ + if (try) + dev_warn(dev, "i2c transfer failed (attempt %d/%d): %d\n", + try + 1, TPM_CR50_I2C_MAX_RETRIES, rc); + usleep_range(TPM_CR50_I2C_RETRY_DELAY_LO, TPM_CR50_I2C_RETRY_DELAY_HI); + } + + /* No i2c message transferred */ + return -EIO; +} + +/** + * tpm_cr50_i2c_read() - Read from TPM register. + * @chip: A TPM chip. + * @addr: Register address to read from. + * @buffer: Read destination, provided by caller. + * @len: Number of bytes to read. + * + * Sends the register address byte to the TPM, then waits until TPM + * is ready via interrupt signal or timeout expiration, then 'len' + * bytes are read from TPM response into the provided 'buffer'. + * + * Return: + * - 0: Success. + * - -errno: A POSIX error code. + */ +static int tpm_cr50_i2c_read(struct tpm_chip *chip, u8 addr, u8 *buffer, size_t len) +{ + struct i2c_client *client = to_i2c_client(chip->dev.parent); + struct i2c_msg msg_reg_addr = { + .addr = client->addr, + .len = 1, + .buf = &addr + }; + struct i2c_msg msg_response = { + .addr = client->addr, + .flags = I2C_M_RD, + .len = len, + .buf = buffer + }; + int rc; + + i2c_lock_bus(client->adapter, I2C_LOCK_SEGMENT); + + /* Prepare for completion interrupt */ + tpm_cr50_i2c_enable_tpm_irq(chip); + + /* Send the register address byte to the TPM */ + rc = tpm_cr50_i2c_transfer_message(&chip->dev, client->adapter, &msg_reg_addr); + if (rc < 0) + goto out; + + /* Wait for TPM to be ready with response data */ + rc = tpm_cr50_i2c_wait_tpm_ready(chip); + if (rc < 0) + goto out; + + /* Read response data from the TPM */ + rc = tpm_cr50_i2c_transfer_message(&chip->dev, client->adapter, &msg_response); + +out: + tpm_cr50_i2c_disable_tpm_irq(chip); + i2c_unlock_bus(client->adapter, I2C_LOCK_SEGMENT); + + if (rc < 0) + return rc; + + return 0; +} + +/** + * tpm_cr50_i2c_write()- Write to TPM register. + * @chip: A TPM chip. + * @addr: Register address to write to. + * @buffer: Data to write. + * @len: Number of bytes to write. + * + * The provided address is prepended to the data in 'buffer', the + * cobined address+data is sent to the TPM, then wait for TPM to + * indicate it is done writing. + * + * Return: + * - 0: Success. + * - -errno: A POSIX error code. + */ +static int tpm_cr50_i2c_write(struct tpm_chip *chip, u8 addr, u8 *buffer, + size_t len) +{ + struct tpm_i2c_cr50_priv_data *priv = dev_get_drvdata(&chip->dev); + struct i2c_client *client = to_i2c_client(chip->dev.parent); + struct i2c_msg msg = { + .addr = client->addr, + .len = len + 1, + .buf = priv->buf + }; + int rc; + + if (len > TPM_CR50_MAX_BUFSIZE - 1) + return -EINVAL; + + /* Prepend the 'register address' to the buffer */ + priv->buf[0] = addr; + memcpy(priv->buf + 1, buffer, len); + + i2c_lock_bus(client->adapter, I2C_LOCK_SEGMENT); + + /* Prepare for completion interrupt */ + tpm_cr50_i2c_enable_tpm_irq(chip); + + /* Send write request buffer with address */ + rc = tpm_cr50_i2c_transfer_message(&chip->dev, client->adapter, &msg); + if (rc < 0) + goto out; + + /* Wait for TPM to be ready, ignore timeout */ + tpm_cr50_i2c_wait_tpm_ready(chip); + +out: + tpm_cr50_i2c_disable_tpm_irq(chip); + i2c_unlock_bus(client->adapter, I2C_LOCK_SEGMENT); + + if (rc < 0) + return rc; + + return 0; +} + +/** + * tpm_cr50_check_locality() - Verify TPM locality 0 is active. + * @chip: A TPM chip. + * + * Return: + * - 0: Success. + * - -errno: A POSIX error code. + */ +static int tpm_cr50_check_locality(struct tpm_chip *chip) +{ + u8 mask = TPM_ACCESS_VALID | TPM_ACCESS_ACTIVE_LOCALITY; + u8 buf; + int rc; + + rc = tpm_cr50_i2c_read(chip, TPM_I2C_ACCESS(0), &buf, sizeof(buf)); + if (rc < 0) + return rc; + + if ((buf & mask) == mask) + return 0; + + return -EIO; +} + +/** + * tpm_cr50_release_locality() - Release TPM locality. + * @chip: A TPM chip. + * @force: Flag to force release if set. + */ +static void tpm_cr50_release_locality(struct tpm_chip *chip, bool force) +{ + u8 mask = TPM_ACCESS_VALID | TPM_ACCESS_REQUEST_PENDING; + u8 addr = TPM_I2C_ACCESS(0); + u8 buf; + + if (tpm_cr50_i2c_read(chip, addr, &buf, sizeof(buf)) < 0) + return; + + if (force || (buf & mask) == mask) { + buf = TPM_ACCESS_ACTIVE_LOCALITY; + tpm_cr50_i2c_write(chip, addr, &buf, sizeof(buf)); + } +} + +/** + * tpm_cr50_request_locality() - Request TPM locality 0. + * @chip: A TPM chip. + * + * Return: + * - 0: Success. + * - -errno: A POSIX error code. + */ +static int tpm_cr50_request_locality(struct tpm_chip *chip) +{ + u8 buf = TPM_ACCESS_REQUEST_USE; + unsigned long stop; + int rc; + + if (!tpm_cr50_check_locality(chip)) + return 0; + + rc = tpm_cr50_i2c_write(chip, TPM_I2C_ACCESS(0), &buf, sizeof(buf)); + if (rc < 0) + return rc; + + stop = jiffies + chip->timeout_a; + do { + if (!tpm_cr50_check_locality(chip)) + return 0; + + msleep(TPM_CR50_TIMEOUT_SHORT_MS); + } while (time_before(jiffies, stop)); + + return -ETIMEDOUT; +} + +/** + * tpm_cr50_i2c_tis_status() - Read cr50 tis status. + * @chip: A TPM chip. + * + * cr50 requires all 4 bytes of status register to be read. + * + * Return: + * TPM status byte. + */ +static u8 tpm_cr50_i2c_tis_status(struct tpm_chip *chip) +{ + u8 buf[4]; + + if (tpm_cr50_i2c_read(chip, TPM_I2C_STS(0), buf, sizeof(buf)) < 0) + return 0; + + return buf[0]; +} + +/** + * tpm_cr50_i2c_tis_set_ready() - Set status register to ready. + * @chip: A TPM chip. + * + * cr50 requires all 4 bytes of status register to be written. + */ +static void tpm_cr50_i2c_tis_set_ready(struct tpm_chip *chip) +{ + u8 buf[4] = { TPM_STS_COMMAND_READY }; + + tpm_cr50_i2c_write(chip, TPM_I2C_STS(0), buf, sizeof(buf)); + msleep(TPM_CR50_TIMEOUT_SHORT_MS); +} + +/** + * tpm_cr50_i2c_get_burst_and_status() - Get burst count and status. + * @chip: A TPM chip. + * @mask: Status mask. + * @burst: Return value for burst. + * @status: Return value for status. + * + * cr50 uses bytes 3:2 of status register for burst count and + * all 4 bytes must be read. + * + * Return: + * - 0: Success. + * - -errno: A POSIX error code. + */ +static int tpm_cr50_i2c_get_burst_and_status(struct tpm_chip *chip, u8 mask, + size_t *burst, u32 *status) +{ + unsigned long stop; + u8 buf[4]; + + *status = 0; + + /* wait for burstcount */ + stop = jiffies + chip->timeout_b; + + do { + if (tpm_cr50_i2c_read(chip, TPM_I2C_STS(0), buf, sizeof(buf)) < 0) { + msleep(TPM_CR50_TIMEOUT_SHORT_MS); + continue; + } + + *status = *buf; + *burst = le16_to_cpup((__le16 *)(buf + 1)); + + if ((*status & mask) == mask && + *burst > 0 && *burst <= TPM_CR50_MAX_BUFSIZE - 1) + return 0; + + msleep(TPM_CR50_TIMEOUT_SHORT_MS); + } while (time_before(jiffies, stop)); + + dev_err(&chip->dev, "Timeout reading burst and status\n"); + return -ETIMEDOUT; +} + +/** + * tpm_cr50_i2c_tis_recv() - TPM reception callback. + * @chip: A TPM chip. + * @buf: Reception buffer. + * @buf_len: Buffer length to read. + * + * Return: + * - >= 0: Number of read bytes. + * - -errno: A POSIX error code. + */ +static int tpm_cr50_i2c_tis_recv(struct tpm_chip *chip, u8 *buf, size_t buf_len) +{ + + u8 mask = TPM_STS_VALID | TPM_STS_DATA_AVAIL; + size_t burstcnt, cur, len, expected; + u8 addr = TPM_I2C_DATA_FIFO(0); + u32 status; + int rc; + + if (buf_len < TPM_HEADER_SIZE) + return -EINVAL; + + rc = tpm_cr50_i2c_get_burst_and_status(chip, mask, &burstcnt, &status); + if (rc < 0) + goto out_err; + + if (burstcnt > buf_len || burstcnt < TPM_HEADER_SIZE) { + dev_err(&chip->dev, + "Unexpected burstcnt: %zu (max=%zu, min=%d)\n", + burstcnt, buf_len, TPM_HEADER_SIZE); + rc = -EIO; + goto out_err; + } + + /* Read first chunk of burstcnt bytes */ + rc = tpm_cr50_i2c_read(chip, addr, buf, burstcnt); + if (rc < 0) { + dev_err(&chip->dev, "Read of first chunk failed\n"); + goto out_err; + } + + /* Determine expected data in the return buffer */ + expected = be32_to_cpup((__be32 *)(buf + 2)); + if (expected > buf_len) { + dev_err(&chip->dev, "Buffer too small to receive i2c data\n"); + goto out_err; + } + + /* Now read the rest of the data */ + cur = burstcnt; + while (cur < expected) { + /* Read updated burst count and check status */ + rc = tpm_cr50_i2c_get_burst_and_status(chip, mask, &burstcnt, &status); + if (rc < 0) + goto out_err; + + len = min_t(size_t, burstcnt, expected - cur); + rc = tpm_cr50_i2c_read(chip, addr, buf + cur, len); + if (rc < 0) { + dev_err(&chip->dev, "Read failed\n"); + goto out_err; + } + + cur += len; + } + + /* Ensure TPM is done reading data */ + rc = tpm_cr50_i2c_get_burst_and_status(chip, TPM_STS_VALID, &burstcnt, &status); + if (rc < 0) + goto out_err; + if (status & TPM_STS_DATA_AVAIL) { + dev_err(&chip->dev, "Data still available\n"); + rc = -EIO; + goto out_err; + } + + tpm_cr50_release_locality(chip, false); + return cur; + +out_err: + /* Abort current transaction if still pending */ + if (tpm_cr50_i2c_tis_status(chip) & TPM_STS_COMMAND_READY) + tpm_cr50_i2c_tis_set_ready(chip); + + tpm_cr50_release_locality(chip, false); + return rc; +} + +/** + * tpm_cr50_i2c_tis_send() - TPM transmission callback. + * @chip: A TPM chip. + * @buf: Buffer to send. + * @len: Buffer length. + * + * Return: + * - 0: Success. + * - -errno: A POSIX error code. + */ +static int tpm_cr50_i2c_tis_send(struct tpm_chip *chip, u8 *buf, size_t len) +{ + size_t burstcnt, limit, sent = 0; + u8 tpm_go[4] = { TPM_STS_GO }; + unsigned long stop; + u32 status; + int rc; + + rc = tpm_cr50_request_locality(chip); + if (rc < 0) + return rc; + + /* Wait until TPM is ready for a command */ + stop = jiffies + chip->timeout_b; + while (!(tpm_cr50_i2c_tis_status(chip) & TPM_STS_COMMAND_READY)) { + if (time_after(jiffies, stop)) { + rc = -ETIMEDOUT; + goto out_err; + } + + tpm_cr50_i2c_tis_set_ready(chip); + } + + while (len > 0) { + u8 mask = TPM_STS_VALID; + + /* Wait for data if this is not the first chunk */ + if (sent > 0) + mask |= TPM_STS_DATA_EXPECT; + + /* Read burst count and check status */ + rc = tpm_cr50_i2c_get_burst_and_status(chip, mask, &burstcnt, &status); + if (rc < 0) + goto out_err; + + /* + * Use burstcnt - 1 to account for the address byte + * that is inserted by tpm_cr50_i2c_write() + */ + limit = min_t(size_t, burstcnt - 1, len); + rc = tpm_cr50_i2c_write(chip, TPM_I2C_DATA_FIFO(0), &buf[sent], limit); + if (rc < 0) { + dev_err(&chip->dev, "Write failed\n"); + goto out_err; + } + + sent += limit; + len -= limit; + } + + /* Ensure TPM is not expecting more data */ + rc = tpm_cr50_i2c_get_burst_and_status(chip, TPM_STS_VALID, &burstcnt, &status); + if (rc < 0) + goto out_err; + if (status & TPM_STS_DATA_EXPECT) { + dev_err(&chip->dev, "Data still expected\n"); + rc = -EIO; + goto out_err; + } + + /* Start the TPM command */ + rc = tpm_cr50_i2c_write(chip, TPM_I2C_STS(0), tpm_go, + sizeof(tpm_go)); + if (rc < 0) { + dev_err(&chip->dev, "Start command failed\n"); + goto out_err; + } + return 0; + +out_err: + /* Abort current transaction if still pending */ + if (tpm_cr50_i2c_tis_status(chip) & TPM_STS_COMMAND_READY) + tpm_cr50_i2c_tis_set_ready(chip); + + tpm_cr50_release_locality(chip, false); + return rc; +} + +/** + * tpm_cr50_i2c_req_canceled() - Callback to notify a request cancel. + * @chip: A TPM chip. + * @status: Status given by the cancel callback. + * + * Return: + * True if command is ready, False otherwise. + */ +static bool tpm_cr50_i2c_req_canceled(struct tpm_chip *chip, u8 status) +{ + return status == TPM_STS_COMMAND_READY; +} + +static const struct tpm_class_ops cr50_i2c = { + .flags = TPM_OPS_AUTO_STARTUP, + .status = &tpm_cr50_i2c_tis_status, + .recv = &tpm_cr50_i2c_tis_recv, + .send = &tpm_cr50_i2c_tis_send, + .cancel = &tpm_cr50_i2c_tis_set_ready, + .req_complete_mask = TPM_STS_DATA_AVAIL | TPM_STS_VALID, + .req_complete_val = TPM_STS_DATA_AVAIL | TPM_STS_VALID, + .req_canceled = &tpm_cr50_i2c_req_canceled, +}; + +static const struct i2c_device_id cr50_i2c_table[] = { + {"cr50_i2c", 0}, + {} +}; +MODULE_DEVICE_TABLE(i2c, cr50_i2c_table); + +#ifdef CONFIG_ACPI +static const struct acpi_device_id cr50_i2c_acpi_id[] = { + { "GOOG0005", 0 }, + {} +}; +MODULE_DEVICE_TABLE(acpi, cr50_i2c_acpi_id); +#endif + +#ifdef CONFIG_OF +static const struct of_device_id of_cr50_i2c_match[] = { + { .compatible = "google,cr50", }, + {} +}; +MODULE_DEVICE_TABLE(of, of_cr50_i2c_match); +#endif + +/** + * tpm_cr50_i2c_probe() - Driver probe function. + * @client: I2C client information. + * @id: I2C device id. + * + * Return: + * - 0: Success. + * - -errno: A POSIX error code. + */ +static int tpm_cr50_i2c_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct tpm_i2c_cr50_priv_data *priv; + struct device *dev = &client->dev; + struct tpm_chip *chip; + u32 vendor; + u8 buf[4]; + int rc; + + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) + return -ENODEV; + + chip = tpmm_chip_alloc(dev, &cr50_i2c); + if (IS_ERR(chip)) + return PTR_ERR(chip); + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + /* cr50 is a TPM 2.0 chip */ + chip->flags |= TPM_CHIP_FLAG_TPM2; + chip->flags |= TPM_CHIP_FLAG_FIRMWARE_POWER_MANAGED; + + /* Default timeouts */ + chip->timeout_a = msecs_to_jiffies(TIS_SHORT_TIMEOUT); + chip->timeout_b = msecs_to_jiffies(TIS_LONG_TIMEOUT); + chip->timeout_c = msecs_to_jiffies(TIS_SHORT_TIMEOUT); + chip->timeout_d = msecs_to_jiffies(TIS_SHORT_TIMEOUT); + + dev_set_drvdata(&chip->dev, priv); + init_completion(&priv->tpm_ready); + + if (client->irq > 0) { + rc = devm_request_irq(dev, client->irq, tpm_cr50_i2c_int_handler, + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, + dev->driver->name, chip); + if (rc < 0) { + dev_err(dev, "Failed to probe IRQ %d\n", client->irq); + return rc; + } + + disable_irq(client->irq); + priv->irq = client->irq; + } else { + dev_warn(dev, "No IRQ, will use %ums delay for TPM ready\n", + TPM_CR50_TIMEOUT_NOIRQ_MS); + } + + rc = tpm_cr50_request_locality(chip); + if (rc < 0) { + dev_err(dev, "Could not request locality\n"); + return rc; + } + + /* Read four bytes from DID_VID register */ + rc = tpm_cr50_i2c_read(chip, TPM_I2C_DID_VID(0), buf, sizeof(buf)); + if (rc < 0) { + dev_err(dev, "Could not read vendor id\n"); + tpm_cr50_release_locality(chip, true); + return rc; + } + + vendor = le32_to_cpup((__le32 *)buf); + if (vendor != TPM_CR50_I2C_DID_VID) { + dev_err(dev, "Vendor ID did not match! ID was %08x\n", vendor); + tpm_cr50_release_locality(chip, true); + return -ENODEV; + } + + dev_info(dev, "cr50 TPM 2.0 (i2c 0x%02x irq %d id 0x%x)\n", + client->addr, client->irq, vendor >> 16); + + return tpm_chip_register(chip); +} + +/** + * tpm_cr50_i2c_remove() - Driver remove function. + * @client: I2C client information. + * + * Return: + * - 0: Success. + * - -errno: A POSIX error code. + */ +static int tpm_cr50_i2c_remove(struct i2c_client *client) +{ + struct tpm_chip *chip = i2c_get_clientdata(client); + struct device *dev = &client->dev; + + if (!chip) { + dev_err(dev, "Could not get client data at remove\n"); + return -ENODEV; + } + + tpm_chip_unregister(chip); + tpm_cr50_release_locality(chip, true); + + return 0; +} + +static SIMPLE_DEV_PM_OPS(cr50_i2c_pm, tpm_pm_suspend, tpm_pm_resume); + +static struct i2c_driver cr50_i2c_driver = { + .id_table = cr50_i2c_table, + .probe = tpm_cr50_i2c_probe, + .remove = tpm_cr50_i2c_remove, + .driver = { + .name = "cr50_i2c", + .pm = &cr50_i2c_pm, + .acpi_match_table = ACPI_PTR(cr50_i2c_acpi_id), + .of_match_table = of_match_ptr(of_cr50_i2c_match), + }, +}; + +module_i2c_driver(cr50_i2c_driver); + +MODULE_DESCRIPTION("cr50 TPM I2C Driver"); +MODULE_LICENSE("GPL");