ARM: at91: Add support for board aks-cdu
Add support for our "aks-cdu" board based up on Telit's module GE863 Pro3. It has more uarts, leds, another nand partitioning. Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz> [nicolas.ferre@atmel.com: correction of the dts file] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This commit is contained in:
Родитель
2e8e4711fe
Коммит
3c68bb4821
|
@ -0,0 +1,113 @@
|
|||
/*
|
||||
* aks-cdu.dts - Device Tree file for AK signal CDU
|
||||
*
|
||||
* Copyright (C) 2012 AK signal Brno a.s.
|
||||
* 2012 Jiri Prchal <jiri.prchal@aksignal.cz>
|
||||
*
|
||||
* Licensed under GPLv2 or later.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
/include/ "ge863-pro3.dtsi"
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200 ubi.mtd=4 root=ubi0:rootfs rootfstype=ubifs";
|
||||
};
|
||||
|
||||
ahb {
|
||||
apb {
|
||||
usart0: serial@fffb0000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usart1: serial@fffb4000 {
|
||||
status = "okay";
|
||||
linux,rs485-enabled-at-boot-time;
|
||||
rs485-rts-delay = <0 0>;
|
||||
};
|
||||
|
||||
usart2: serial@fffb8000 {
|
||||
status = "okay";
|
||||
linux,rs485-enabled-at-boot-time;
|
||||
rs485-rts-delay = <0 0>;
|
||||
};
|
||||
|
||||
usart3: serial@fffd0000 {
|
||||
status = "okay";
|
||||
linux,rs485-enabled-at-boot-time;
|
||||
rs485-rts-delay = <0 0>;
|
||||
};
|
||||
|
||||
macb0: ethernet@fffc4000 {
|
||||
phy-mode = "rmii";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb1: gadget@fffa4000 {
|
||||
atmel,vbus-gpio = <&pioC 15 0>;
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
usb0: ohci@00500000 {
|
||||
num-ports = <2>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
nand0: nand@40000000 {
|
||||
nand-bus-width = <8>;
|
||||
nand-ecc-mode = "soft";
|
||||
nand-on-flash-bbt;
|
||||
status = "okay";
|
||||
|
||||
bootstrap@0 {
|
||||
label = "bootstrap";
|
||||
reg = <0x0 0x40000>;
|
||||
};
|
||||
|
||||
uboot@40000 {
|
||||
label = "uboot";
|
||||
reg = <0x40000 0x80000>;
|
||||
};
|
||||
ubootenv@c0000 {
|
||||
label = "ubootenv";
|
||||
reg = <0xc0000 0x40000>;
|
||||
};
|
||||
kernel@100000 {
|
||||
label = "kernel";
|
||||
reg = <0x100000 0x400000>;
|
||||
};
|
||||
rootfs@500000 {
|
||||
label = "rootfs";
|
||||
reg = <0x500000 0x7b00000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
red {
|
||||
gpios = <&pioC 10 0>;
|
||||
linux,default-trigger = "none";
|
||||
};
|
||||
|
||||
green {
|
||||
gpios = <&pioA 5 1>;
|
||||
linux,default-trigger = "none";
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
yellow {
|
||||
gpios = <&pioB 20 1>;
|
||||
linux,default-trigger = "none";
|
||||
};
|
||||
|
||||
blue {
|
||||
gpios = <&pioB 21 1>;
|
||||
linux,default-trigger = "none";
|
||||
};
|
||||
};
|
||||
};
|
|
@ -15,6 +15,7 @@ endif
|
|||
|
||||
# Keep dtb files sorted alphabetically for each SoC
|
||||
# sam9260
|
||||
dtb-$(CONFIG_MACH_AT91SAM_DT) += aks-cdu.dtb
|
||||
dtb-$(CONFIG_MACH_AT91SAM_DT) += ethernut5.dtb
|
||||
dtb-$(CONFIG_MACH_AT91SAM_DT) += evk-pro3.dtb
|
||||
dtb-$(CONFIG_MACH_AT91SAM_DT) += tny_a9260.dtb
|
||||
|
|
Загрузка…
Ссылка в новой задаче