dt-bindings: iio: adc: Migrate AD7606 documentation to yaml
The documentation for ad7606 was migrated to yaml. Signed-off-by: Beniamin Bia <beniamin.bia@analog.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit is contained in:
Beniamin Bia
Jonathan Cameron
Родитель
75338cc8eb
Коммит
416f882c3b
|
|
@ -1,66 +0,0 @@
|
|||
Analog Devices AD7606 Simultaneous Sampling ADC
|
||||
|
||||
Required properties for the AD7606:
|
||||
|
||||
- compatible: Must be one of
|
||||
* "adi,ad7605-4"
|
||||
* "adi,ad7606-8"
|
||||
* "adi,ad7606-6"
|
||||
* "adi,ad7606-4"
|
||||
* "adi,ad7616"
|
||||
- reg: SPI chip select number for the device
|
||||
- spi-max-frequency: Max SPI frequency to use
|
||||
see: Documentation/devicetree/bindings/spi/spi-bus.txt
|
||||
- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
|
||||
- avcc-supply: phandle to the Avcc power supply
|
||||
- interrupts: IRQ line for the ADC
|
||||
see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
|
||||
- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin.
|
||||
This logic input is used to initiate conversions on the analog
|
||||
input channels. As the line is active high, it should be marked
|
||||
GPIO_ACTIVE_HIGH.
|
||||
|
||||
Optional properties:
|
||||
|
||||
- reset-gpios: must be the device tree identifier of the RESET pin. If specified,
|
||||
it will be asserted during driver probe. As the line is active high,
|
||||
it should be marked GPIO_ACTIVE_HIGH.
|
||||
- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used
|
||||
to place the AD7606 into one of two power-down modes, Standby mode or
|
||||
Shutdown mode. As the line is active low, it should be marked
|
||||
GPIO_ACTIVE_LOW.
|
||||
- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin.
|
||||
The FRSTDATA output indicates when the first channel, V1, is
|
||||
being read back on either the parallel, byte or serial interface.
|
||||
As the line is active high, it should be marked GPIO_ACTIVE_HIGH.
|
||||
- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on
|
||||
this pin determines the input range of the analog input channels. If
|
||||
this pin is tied to a logic high, the analog input range is ±10V for
|
||||
all channels. If this pin is tied to a logic low, the analog input range
|
||||
is ±5V for all channels. As the line is active high, it should be marked
|
||||
GPIO_ACTIVE_HIGH.
|
||||
- adi,oversampling-ratio-gpios: must be the device tree identifier of the over-sampling
|
||||
mode pins. As the line is active high, it should be marked
|
||||
GPIO_ACTIVE_HIGH.
|
||||
|
||||
Example:
|
||||
|
||||
adc@0 {
|
||||
compatible = "adi,ad7606-8";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <1000000>;
|
||||
spi-cpol;
|
||||
|
||||
avcc-supply = <&adc_vref>;
|
||||
|
||||
interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupt-parent = <&gpio>;
|
||||
|
||||
adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
|
||||
reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
|
||||
adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
|
||||
adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH
|
||||
&gpio 23 GPIO_ACTIVE_HIGH
|
||||
&gpio 26 GPIO_ACTIVE_HIGH>;
|
||||
standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
|
@ -0,0 +1,136 @@
|
|||
# SPDX-License-Identifier: GPL-2.0
|
||||
%YAML 1.2
|
||||
---
|
||||
$id: http://devicetree.org/schemas/iio/adc/adi,ad7606.yaml#
|
||||
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||||
|
||||
title: Analog Devices AD7606 Simultaneous Sampling ADC
|
||||
|
||||
maintainers:
|
||||
- Beniamin Bia <beniamin.bia@analog.com>
|
||||
- Stefan Popa <stefan.popa@analog.com>
|
||||
|
||||
description: |
|
||||
Analog Devices AD7606 Simultaneous Sampling ADC
|
||||
https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf
|
||||
https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf
|
||||
|
||||
properties:
|
||||
compatible:
|
||||
enum:
|
||||
- adi,ad7605-4
|
||||
- adi,ad7606-8
|
||||
- adi,ad7606-6
|
||||
- adi,ad7606-4
|
||||
- adi,ad7616
|
||||
|
||||
reg:
|
||||
maxItems: 1
|
||||
|
||||
spi-cpha: true
|
||||
|
||||
avcc-supply:
|
||||
description:
|
||||
Phandle to the Avcc power supply
|
||||
maxItems: 1
|
||||
|
||||
interrupts:
|
||||
maxItems: 1
|
||||
|
||||
adi,conversion-start-gpios:
|
||||
description:
|
||||
Must be the device tree identifier of the CONVST pin.
|
||||
This logic input is used to initiate conversions on the analog
|
||||
input channels. As the line is active high, it should be marked
|
||||
GPIO_ACTIVE_HIGH.
|
||||
maxItems: 1
|
||||
|
||||
reset-gpios:
|
||||
description:
|
||||
Must be the device tree identifier of the RESET pin. If specified,
|
||||
it will be asserted during driver probe. As the line is active high,
|
||||
it should be marked GPIO_ACTIVE_HIGH.
|
||||
maxItems: 1
|
||||
|
||||
standby-gpios:
|
||||
description:
|
||||
Must be the device tree identifier of the STBY pin. This pin is used
|
||||
to place the AD7606 into one of two power-down modes, Standby mode or
|
||||
Shutdown mode. As the line is active low, it should be marked
|
||||
GPIO_ACTIVE_LOW.
|
||||
maxItems: 1
|
||||
|
||||
adi,first-data-gpios:
|
||||
description:
|
||||
Must be the device tree identifier of the FRSTDATA pin.
|
||||
The FRSTDATA output indicates when the first channel, V1, is
|
||||
being read back on either the parallel, byte or serial interface.
|
||||
As the line is active high, it should be marked GPIO_ACTIVE_HIGH.
|
||||
maxItems: 1
|
||||
|
||||
adi,range-gpios:
|
||||
description:
|
||||
Must be the device tree identifier of the RANGE pin. The polarity on
|
||||
this pin determines the input range of the analog input channels. If
|
||||
this pin is tied to a logic high, the analog input range is ±10V for
|
||||
all channels. If this pin is tied to a logic low, the analog input range
|
||||
is ±5V for all channels. As the line is active high, it should be marked
|
||||
GPIO_ACTIVE_HIGH.
|
||||
maxItems: 1
|
||||
|
||||
adi,oversampling-ratio-gpios:
|
||||
description:
|
||||
Must be the device tree identifier of the over-sampling
|
||||
mode pins. As the line is active high, it should be marked
|
||||
GPIO_ACTIVE_HIGH.
|
||||
maxItems: 1
|
||||
|
||||
adi,sw-mode:
|
||||
description:
|
||||
Software mode of operation, so far available only for ad7616.
|
||||
It is enabled when all three oversampling mode pins are connected to
|
||||
high level. The device is configured by the corresponding registers. If the
|
||||
adi,oversampling-ratio-gpios property is defined, then the driver will set the
|
||||
oversampling gpios to high. Otherwise, it is assumed that the pins are hardwired
|
||||
to VDD.
|
||||
type: boolean
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- reg
|
||||
- spi-cpha
|
||||
- avcc-supply
|
||||
- interrupts
|
||||
- adi,conversion-start-gpios
|
||||
|
||||
examples:
|
||||
- |
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
spi0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
adc@0 {
|
||||
compatible = "adi,ad7606-8";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <1000000>;
|
||||
spi-cpol;
|
||||
spi-cpha;
|
||||
|
||||
avcc-supply = <&adc_vref>;
|
||||
|
||||
interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupt-parent = <&gpio>;
|
||||
|
||||
adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
|
||||
reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
|
||||
adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
|
||||
adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH
|
||||
&gpio 23 GPIO_ACTIVE_HIGH
|
||||
&gpio 26 GPIO_ACTIVE_HIGH>;
|
||||
standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
|
||||
adi,sw-mode;
|
||||
};
|
||||
};
|
||||
...
|
||||
|
|
@ -908,7 +908,7 @@ L: linux-iio@vger.kernel.org
|
|||
W: http://ez.analog.com/community/linux-device-drivers
|
||||
S: Supported
|
||||
F: drivers/iio/adc/ad7606.c
|
||||
F: Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
|
||||
F: Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml
|
||||
|
||||
ANALOG DEVICES INC AD7768-1 DRIVER
|
||||
M: Stefan Popa <stefan.popa@analog.com>
|
||||
|
|
|
|||
Загрузка…
Ссылка в новой задаче