arm64: dts: add device tree for Traverse Ten64 (LS1088A)
The Traverse Technologies Ten64 is a Mini-ITX form factor networking board using the NXP LS1088A SoC. This device tree only describes features which the mainline kernel currently has support for, such as some I2C-connected devices that are not described at present. System documentation may be found at ten64doc.traverse.com.au Signed-off-by: Mathew McBride <matt@traverse.com.au> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> # for the MAC/PHY Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit is contained in:
Mathew McBride
Shawn Guo
Родитель
2cfad132b5
Коммит
418962eea3
|
|
@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb
|
|||
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb
|
||||
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-qds.dtb
|
||||
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-rdb.dtb
|
||||
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-ten64.dtb
|
||||
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb
|
||||
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
|
||||
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
|
||||
|
|
|
|||
|
|
@ -0,0 +1,389 @@
|
|||
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
/*
|
||||
* Device Tree file for Travese Ten64 (LS1088) board
|
||||
* Based on fsl-ls1088a-rdb.dts
|
||||
* Copyright 2017-2020 NXP
|
||||
* Copyright 2019-2021 Traverse Technologies
|
||||
*
|
||||
* Author: Mathew McBride <matt@traverse.com.au>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "fsl-ls1088a.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "Traverse Ten64";
|
||||
compatible = "traverse,ten64", "fsl,ls1088a";
|
||||
|
||||
aliases {
|
||||
serial0 = &duart0;
|
||||
serial1 = &duart1;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
buttons {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
/* Fired by system controller when
|
||||
* external power off (e.g ATX Power Button)
|
||||
* asserted
|
||||
*/
|
||||
powerdn {
|
||||
label = "External Power Down";
|
||||
gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
|
||||
interrupts = <&gpio1 17 IRQ_TYPE_EDGE_FALLING>;
|
||||
linux,code = <KEY_POWER>;
|
||||
};
|
||||
|
||||
/* Rear Panel 'ADMIN' button (GPIO_H) */
|
||||
admin {
|
||||
label = "ADMIN button";
|
||||
gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
|
||||
interrupts = <&gpio3 8 IRQ_TYPE_EDGE_RISING>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
sfp1down {
|
||||
label = "ten64:green:sfp1:down";
|
||||
gpios = <&gpio3 11 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
sfp2up {
|
||||
label = "ten64:green:sfp2:up";
|
||||
gpios = <&gpio3 12 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
admin {
|
||||
label = "ten64:admin";
|
||||
gpios = <&sfpgpio 12 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
sfp_xg0: dpmac2-sfp {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&sfplower_i2c>;
|
||||
tx-fault-gpios = <&sfpgpio 0 GPIO_ACTIVE_HIGH>;
|
||||
tx-disable-gpios = <&sfpgpio 1 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpios = <&sfpgpio 2 GPIO_ACTIVE_LOW>;
|
||||
los-gpios = <&sfpgpio 3 GPIO_ACTIVE_HIGH>;
|
||||
maximum-power-milliwatt = <2000>;
|
||||
};
|
||||
|
||||
sfp_xg1: dpmac1-sfp {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&sfpupper_i2c>;
|
||||
tx-fault-gpios = <&sfpgpio 4 GPIO_ACTIVE_HIGH>;
|
||||
tx-disable-gpios = <&sfpgpio 5 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpios = <&sfpgpio 6 GPIO_ACTIVE_LOW>;
|
||||
los-gpios = <&sfpgpio 7 GPIO_ACTIVE_HIGH>;
|
||||
maximum-power-milliwatt = <2000>;
|
||||
};
|
||||
};
|
||||
|
||||
/* XG1 - Upper SFP */
|
||||
&dpmac1 {
|
||||
sfp = <&sfp_xg1>;
|
||||
pcs-handle = <&pcs1>;
|
||||
phy-connection-type = "10gbase-r";
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
/* XG0 - Lower SFP */
|
||||
&dpmac2 {
|
||||
sfp = <&sfp_xg0>;
|
||||
pcs-handle = <&pcs2>;
|
||||
phy-connection-type = "10gbase-r";
|
||||
managed = "in-band-status";
|
||||
};
|
||||
|
||||
/* DPMAC3..6 is GE4 to GE8 */
|
||||
&dpmac3 {
|
||||
phy-handle = <&mdio1_phy5>;
|
||||
phy-connection-type = "qsgmii";
|
||||
managed = "in-band-status";
|
||||
pcs-handle = <&pcs3_0>;
|
||||
};
|
||||
|
||||
&dpmac4 {
|
||||
phy-handle = <&mdio1_phy6>;
|
||||
phy-connection-type = "qsgmii";
|
||||
managed = "in-band-status";
|
||||
pcs-handle = <&pcs3_1>;
|
||||
};
|
||||
|
||||
&dpmac5 {
|
||||
phy-handle = <&mdio1_phy7>;
|
||||
phy-connection-type = "qsgmii";
|
||||
managed = "in-band-status";
|
||||
pcs-handle = <&pcs3_2>;
|
||||
};
|
||||
|
||||
&dpmac6 {
|
||||
phy-handle = <&mdio1_phy8>;
|
||||
phy-connection-type = "qsgmii";
|
||||
managed = "in-band-status";
|
||||
pcs-handle = <&pcs3_3>;
|
||||
};
|
||||
|
||||
/* DPMAC7..10 is GE0 to GE3 */
|
||||
&dpmac7 {
|
||||
phy-handle = <&mdio1_phy1>;
|
||||
phy-connection-type = "qsgmii";
|
||||
managed = "in-band-status";
|
||||
pcs-handle = <&pcs7_0>;
|
||||
};
|
||||
|
||||
&dpmac8 {
|
||||
phy-handle = <&mdio1_phy2>;
|
||||
phy-connection-type = "qsgmii";
|
||||
managed = "in-band-status";
|
||||
pcs-handle = <&pcs7_1>;
|
||||
};
|
||||
|
||||
&dpmac9 {
|
||||
phy-handle = <&mdio1_phy3>;
|
||||
phy-connection-type = "qsgmii";
|
||||
managed = "in-band-status";
|
||||
pcs-handle = <&pcs7_2>;
|
||||
};
|
||||
|
||||
&dpmac10 {
|
||||
phy-handle = <&mdio1_phy4>;
|
||||
phy-connection-type = "qsgmii";
|
||||
managed = "in-band-status";
|
||||
pcs-handle = <&pcs7_3>;
|
||||
};
|
||||
|
||||
&duart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&duart1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&emdio1 {
|
||||
status = "okay";
|
||||
|
||||
mdio1_phy5: ethernet-phy@c {
|
||||
reg = <0xc>;
|
||||
};
|
||||
|
||||
mdio1_phy6: ethernet-phy@d {
|
||||
reg = <0xd>;
|
||||
};
|
||||
|
||||
mdio1_phy7: ethernet-phy@e {
|
||||
reg = <0xe>;
|
||||
};
|
||||
|
||||
mdio1_phy8: ethernet-phy@f {
|
||||
reg = <0xf>;
|
||||
};
|
||||
|
||||
mdio1_phy1: ethernet-phy@1c {
|
||||
reg = <0x1c>;
|
||||
};
|
||||
|
||||
mdio1_phy2: ethernet-phy@1d {
|
||||
reg = <0x1d>;
|
||||
};
|
||||
|
||||
mdio1_phy3: ethernet-phy@1e {
|
||||
reg = <0x1e>;
|
||||
};
|
||||
|
||||
mdio1_phy4: ethernet-phy@1f {
|
||||
reg = <0x1f>;
|
||||
};
|
||||
};
|
||||
|
||||
&esdhc {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
status = "okay";
|
||||
|
||||
sfpgpio: gpio@76 {
|
||||
compatible = "ti,tca9539";
|
||||
reg = <0x76>;
|
||||
#gpio-cells = <2>;
|
||||
gpio-controller;
|
||||
|
||||
admin_led_lower {
|
||||
gpio-hog;
|
||||
gpios = <13 GPIO_ACTIVE_HIGH>;
|
||||
output-low;
|
||||
};
|
||||
};
|
||||
|
||||
at97sc: tpm@29 {
|
||||
compatible = "atmel,at97sc3204t";
|
||||
reg = <0x29>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
status = "okay";
|
||||
|
||||
rx8035: rtc@32 {
|
||||
compatible = "epson,rx8035";
|
||||
reg = <0x32>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c3 {
|
||||
status = "okay";
|
||||
|
||||
i2c-switch@70 {
|
||||
compatible = "nxp,pca9540";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x70>;
|
||||
|
||||
sfpupper_i2c: i2c@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
sfplower_i2c: i2c@1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcs_mdio1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcs_mdio2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcs_mdio3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcs_mdio7 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qspi {
|
||||
status = "okay";
|
||||
|
||||
en25s64: flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
spi-max-frequency = <20000000>;
|
||||
spi-rx-bus-width = <4>;
|
||||
spi-tx-bus-width = <4>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "bl2";
|
||||
reg = <0 0x100000>;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "bl3";
|
||||
reg = <0x100000 0x200000>;
|
||||
};
|
||||
|
||||
partition@300000 {
|
||||
label = "mcfirmware";
|
||||
reg = <0x300000 0x200000>;
|
||||
};
|
||||
|
||||
partition@500000 {
|
||||
label = "ubootenv";
|
||||
reg = <0x500000 0x80000>;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "dpl";
|
||||
reg = <0x580000 0x40000>;
|
||||
};
|
||||
|
||||
partition@5C0000 {
|
||||
label = "dpc";
|
||||
reg = <0x5C0000 0x40000>;
|
||||
};
|
||||
|
||||
partition@600000 {
|
||||
label = "devicetree";
|
||||
reg = <0x600000 0x40000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
nand: flash@1 {
|
||||
compatible = "spi-nand";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <1>;
|
||||
spi-max-frequency = <20000000>;
|
||||
spi-rx-bus-width = <4>;
|
||||
spi-tx-bus-width = <4>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
/* reserved for future boot direct from NAND flash
|
||||
* (this would use the same layout as the 8MiB NOR flash)
|
||||
*/
|
||||
partition@0 {
|
||||
label = "nand-boot-reserved";
|
||||
reg = <0 0x800000>;
|
||||
};
|
||||
|
||||
/* recovery / install environment */
|
||||
partition@800000 {
|
||||
label = "recovery";
|
||||
reg = <0x800000 0x2000000>;
|
||||
};
|
||||
|
||||
/* ubia (first OpenWrt) - a/b names to prevent confusion with ubi0/1/etc. */
|
||||
partition@2800000 {
|
||||
label = "ubia";
|
||||
reg = <0x2800000 0x6C00000>;
|
||||
};
|
||||
|
||||
/* ubib (second OpenWrt) */
|
||||
partition@9400000 {
|
||||
label = "ubib";
|
||||
reg = <0x9400000 0x6C00000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb1 {
|
||||
status = "okay";
|
||||
};
|
||||
Загрузка…
Ссылка в новой задаче