USB: Refactor hub_port_wait_reset.

Refactor hub_port_wait_reset into a small loop to wait for the port
reset to be complete, and then a larger block to deal with the final
port status.  This patch should not change any current behavior.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>

drivers/usb/core/hub.c

@@ -2535,42 +2535,9 @@ static int hub_port_wait_reset(struct usb_hub *hub, int port1,
 			return ret;
 
 		/* The port state is unknown until the reset completes. */
-		if ((portstatus & USB_PORT_STAT_RESET))
-			goto delay;
+		if (!(portstatus & USB_PORT_STAT_RESET))
+			break;
 
-		if (hub_port_warm_reset_required(hub, portstatus))
-			return -ENOTCONN;
-
-		/* Device went away? */
-		if (!(portstatus & USB_PORT_STAT_CONNECTION))
-			return -ENOTCONN;
-
-		/* bomb out completely if the connection bounced.  A USB 3.0
-		 * connection may bounce if multiple warm resets were issued,
-		 * but the device may have successfully re-connected. Ignore it.
-		 */
-		if (!hub_is_superspeed(hub->hdev) &&
-				(portchange & USB_PORT_STAT_C_CONNECTION))
-			return -ENOTCONN;
-
-		if ((portstatus & USB_PORT_STAT_ENABLE)) {
-			if (!udev)
-				return 0;
-
-			if (hub_is_wusb(hub))
-				udev->speed = USB_SPEED_WIRELESS;
-			else if (hub_is_superspeed(hub->hdev))
-				udev->speed = USB_SPEED_SUPER;
-			else if (portstatus & USB_PORT_STAT_HIGH_SPEED)
-				udev->speed = USB_SPEED_HIGH;
-			else if (portstatus & USB_PORT_STAT_LOW_SPEED)
-				udev->speed = USB_SPEED_LOW;
-			else
-				udev->speed = USB_SPEED_FULL;
-			return 0;
-		}
-
-delay:
 		/* switch to the long delay after two short delay failures */
 		if (delay_time >= 2 * HUB_SHORT_RESET_TIME)
 			delay = HUB_LONG_RESET_TIME;
@@ -2580,7 +2547,41 @@ delay:
 			port1, warm ? "warm " : "", delay);
 	}
 
-	return -EBUSY;
+	if ((portstatus & USB_PORT_STAT_RESET))
+		return -EBUSY;
+
+	if (hub_port_warm_reset_required(hub, portstatus))
+		return -ENOTCONN;
+
+	/* Device went away? */
+	if (!(portstatus & USB_PORT_STAT_CONNECTION))
+		return -ENOTCONN;
+
+	/* bomb out completely if the connection bounced.  A USB 3.0
+	 * connection may bounce if multiple warm resets were issued,
+	 * but the device may have successfully re-connected. Ignore it.
+	 */
+	if (!hub_is_superspeed(hub->hdev) &&
+			(portchange & USB_PORT_STAT_C_CONNECTION))
+		return -ENOTCONN;
+
+	if (!(portstatus & USB_PORT_STAT_ENABLE))
+		return -EBUSY;
+
+	if (!udev)
+		return 0;
+
+	if (hub_is_wusb(hub))
+		udev->speed = USB_SPEED_WIRELESS;
+	else if (hub_is_superspeed(hub->hdev))
+		udev->speed = USB_SPEED_SUPER;
+	else if (portstatus & USB_PORT_STAT_HIGH_SPEED)
+		udev->speed = USB_SPEED_HIGH;
+	else if (portstatus & USB_PORT_STAT_LOW_SPEED)
+		udev->speed = USB_SPEED_LOW;
+	else
+		udev->speed = USB_SPEED_FULL;
+	return 0;
 }
 
 static void hub_port_finish_reset(struct usb_hub *hub, int port1,