microsoft
/
WSL2-Linux-Kernel
зеркало из https://github.com/microsoft/WSL2-Linux-Kernel.git
1
0
Форкнуть 0
Код Задачи Пакеты Проекты Релизы Вики Активность

i.MX device tree change for 5.12: 

- A series from Oleksij Rempel to add i.MX6 based Plymovent, Protonic
   and Kverneland boards.
 - A series from Andreas Kemnade to improve UART support for ebook
   readers.
 - A series from Fabio Estevam to update imx6ul-14x14-evk device tree for
   adding GPIO expander and camera support.
 - A patch set from Lucas Stach to improve ZII RDU2 support, enabling
   WDOG, tuning I2C drive-strength, RMI4 and UCS1002 ALERT.
 - Other small and random updates on various boards.
 -----BEGIN PGP SIGNATURE-----
 
 iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmAbmf8UHHNoYXduZ3Vv
 QGtlcm5lbC5vcmcACgkQUFdYWoewfM5xXwgAlGHKq/arFxIkQf0xUcJzLhJ9FcDl
 CpNz77cosCXERcoVpRgTYWGk1ElnYutyNMkUzSrhXdZ80ieL5UMF/RAZYaGJO38f
 NLCN5Rv5w1i4z/J8GGhqASgZ13Pized6jcEuvd8EYwVNkRX+ErcKszkmjWit42RL
 cgRtdBhqAmEwshNjtki5PbFRj7YxWuC6Tsf4OUyXmm4S/+sqcaTvLuQWq/AeEzqJ
 5vN1H6RFqfZR+C2vumW/Yq4bkRlFQllELcoTPPrixm2ZvvZbLs7I56HZub9yom9i
 c4GCfcSgMEXjmuB3h7NmMNyPCyvSVLN3bNseYADX9PnrBzP4HFRW1IsAhg==
 =DmjV
 -----END PGP SIGNATURE-----

Merge tag 'imx-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt

i.MX device tree change for 5.12:

- A series from Oleksij Rempel to add i.MX6 based Plymovent, Protonic
  and Kverneland boards.
- A series from Andreas Kemnade to improve UART support for ebook
  readers.
- A series from Fabio Estevam to update imx6ul-14x14-evk device tree for
  adding GPIO expander and camera support.
- A patch set from Lucas Stach to improve ZII RDU2 support, enabling
  WDOG, tuning I2C drive-strength, RMI4 and UCS1002 ALERT.
- Other small and random updates on various boards.

* tag 'imx-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (37 commits)
  ARM: dts: imx6: RDU2: adjust audio devices nomenclature
  ARM: dts: imx6: RDU2: only trigger IRQ on falling edge ucs1002 ALERT pin
  ARM: dts: imx6: RDU2: enable RMI4 reduced reporting
  ARM: dts: imx6: RDU2: reduce i2c drive-strength
  ARM: dts: imx6: rdu2: enable WDOG1
  ARM: dts: imx6-sr-som: increase at8035 PHY gigabit Tw parameter
  ARM: dts: imx6: add wakeup support via magic packet
  firmware: imx: select SOC_BUS to fix firmware build
  arm64: dts: imx8mp: Correct the gpio ranges of gpio3
  ARM: dts: imx6qdl-sr-som: fix some cubox-i platforms
  ARM: dts: imx: e60k02: add second uart
  ARM: dts: imx6sl-tolino-shine3: correct console uart pinmux
  ARM: dts: imx6sl-tolino-shine2hd: add second uart
  ARM: dts: imx6sl-tolino-shine2hd: correct console uart pinmux
  ARM: imx: build suspend-imx6.S with arm instruction set
  ARM: dts: imx7d-flex-concentrator: fix pcf2127 reset
  ARM: dts: add Kverneland TGO board
  ARM: dts: add Kverneland UT1, UT1Q and UT1P
  ARM: dts: imx6ul-14x14-evk: Add camera support
  ARM: dts: imx6ul-14x14-evk: Describe the KSZ8081 reset
  ...

Link: https://lore.kernel.org/r/20210204120150.26186-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This commit is contained in:
Arnd Bergmann 2021-02-09 18:01:41 +01:00
Родитель 6f771ce6c3 498f8aee6e
Коммит 48a60549d2
35 изменённых файлов: 3945 добавлений и 59 удалений
Показать статистику Скачать Patch файл Скачать Diff файл Показать все файлы Свернуть все файлы

8
arch/arm/boot/dts/Makefile
Просмотреть файл

@ -465,6 +465,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-pico-hobbit.dtb \
imx6dl-pico-nymph.dtb \
imx6dl-pico-pi.dtb \
imx6dl-plybas.dtb \
imx6dl-plym2m.dtb \
imx6dl-prtmvt.dtb \
imx6dl-prtrvt.dtb \
imx6dl-prtvt7.dtb \
imx6dl-rex-basic.dtb \
@ -487,6 +490,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-tx6u-811x.dtb \
imx6dl-tx6u-81xx-mb7.dtb \
imx6dl-udoo.dtb \
imx6dl-victgo.dtb \
imx6dl-vicut1.dtb \
imx6dl-wandboard.dtb \
imx6dl-wandboard-revb1.dtb \
imx6dl-wandboard-revd1.dtb \
@ -580,6 +585,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-udoo.dtb \
imx6q-utilite-pro.dtb \
imx6q-var-dt6customboard.dtb \
imx6q-vicut1.dtb \
imx6q-wandboard.dtb \
imx6q-wandboard-revb1.dtb \
imx6q-wandboard-revd1.dtb \
@ -594,6 +600,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6qp-tx6qp-8037-mb7.dtb \
imx6qp-tx6qp-8137.dtb \
imx6qp-tx6qp-8137-mb7.dtb \
imx6qp-vicutp.dtb \
imx6qp-wandboard-revd1.dtb \
imx6qp-zii-rdu2.dtb
dtb-$(CONFIG_SOC_IMX6SL) += \
@ -631,6 +638,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-pico-pi.dtb \
imx6ul-phytec-segin-ff-rdk-emmc.dtb \
imx6ul-phytec-segin-ff-rdk-nand.dtb \
imx6ul-prti6g.dtb \
imx6ul-tx6ul-0010.dtb \
imx6ul-tx6ul-0011.dtb \
imx6ul-tx6ul-mainboard.dtb \

6
arch/arm/boot/dts/e60k02.dtsi
Просмотреть файл

@ -278,6 +278,12 @@
};
&uart1 {
/* J4, through-hole */
status = "okay";
};
&uart4 {
/* TP198, next to J4, SMD pads */
status = "okay";
};

10
arch/arm/boot/dts/imx28.dtsi
Просмотреть файл

@ -948,6 +948,16 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
usb1_pins_b: usb1@1 {
reg = <1>;
fsl,pinmux-ids = <
MX28_PAD_PWM2__USB1_OVERCURRENT
>;
fsl,drive-strength = <MXS_DRIVE_12mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
usb0_id_pins_a: usb0id@0 {
reg = <0>;
fsl,pinmux-ids = <

1
arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
Просмотреть файл

@ -238,7 +238,6 @@
compatible = "wlf,wm8962";
reg = <0x1a>;
clocks = <&clks IMX6QDL_CLK_CKO>;
clock-names = "xclk";
DCVDD-supply = <&reg_audio>;
DBVDD-supply = <&reg_audio>;
AVDD-supply = <&reg_audio>;

394
arch/arm/boot/dts/imx6dl-plybas.dts Normal file
Просмотреть файл

@ -0,0 +1,394 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Copyright (c) 2014 Protonic Holland
* Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
#include "imx6dl.dtsi"
/ {
model = "Plymovent BAS board";
compatible = "ply,plybas", "fsl,imx6dl";
chosen {
stdout-path = &uart4;
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
autorepeat;
button@20 {
label = "START";
linux,code = <31>;
gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
};
button@21 {
label = "CLEAN";
linux,code = <46>;
gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_leds>;
led-0 {
label = "debug0";
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
};
led-1 {
label = "debug1";
gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
};
led-2 {
label = "light_tower1";
gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
led-3 {
label = "light_tower2";
gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
};
led-4 {
label = "light_tower3";
gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
};
led-5 {
label = "light_tower4";
gpios = <&gpio4 25 GPIO_ACTIVE_HIGH>;
};
};
clk50m_phy: phy-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <50000000>;
};
reg_5v0: regulator-5v0 {
compatible = "regulator-fixed";
regulator-name = "5v0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
};
&can1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1>;
xceiver-supply = <&reg_5v0>;
status = "okay";
};
&can2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can2>;
xceiver-supply = <&reg_5v0>;
status = "okay";
};
&ecspi1 {
cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <20000000>;
};
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rmii";
clocks = <&clks IMX6QDL_CLK_ENET>,
<&clks IMX6QDL_CLK_ENET>,
<&clk50m_phy>;
clock-names = "ipg", "ahb", "ptp";
phy-handle = <&rgmii_phy>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
/* Microchip KSZ8081RNA PHY */
rgmii_phy: ethernet-phy@0 {
reg = <0>;
interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
reset-assert-us = <10000>;
reset-deassert-us = <300>;
};
};
};
&gpio1 {
gpio-line-names =
"", "SD1_CD", "", "", "", "", "", "",
"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "";
};
&gpio3 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "ECSPI1_SS1", "", "USB_EXT_PWR", "", "",
"", "", "", "", "", "", "", "";
};
&gpio4 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"", "", "", "", "CAN1_SR", "CAN2_SR", "", "",
"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "IMX6_IN12", "IMX6_HMI",
"IMX6_IN11", "IMX6_BUZZER", "IMX6_LED1", "IMX6_LED2",
"IMX6_LED3", "IMX6_LED4", "ETH_RESET", "IMX6_ANA_OUT_SD",
"IMX6_ANA_OUT_ERR", "IMX6_ANA_OUT", "ETH_INTRP", "";
};
&gpio5 {
gpio-line-names =
"", "", "", "", "", "IMX6_RELAY1", "IMX6_RELAY2", "",
"IMX6_IN1", "IMX6_IN2", "IMX6_IN3", "IMX6_IN4", "IMX6_IN5",
"IMX6_IN6", "IMX6_IN7", "IMX6_IN8",
"IMX6_IN9", "IMX6_IN10", "", "", "", "", "", "",
"", "", "", "", "", "", "", "";
};
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
/* additional i2c devices are added automatically by the boot loader */
};
&i2c3 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
temperature-sensor@70 {
compatible = "ti,tmp103";
reg = <0x70>;
};
rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
};
};
&pwm1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
fsl,uart-has-rtscts;
linux,rs485-enabled-at-boot-time;
rs485-rts-delay = <0 20>;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
status = "okay";
};
&usbotg {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
phy_type = "utmi";
dr_mode = "host";
disable-over-current;
status = "okay";
};
&usbphynop1 {
status = "disabled";
};
&usbphynop2 {
status = "disabled";
};
&iomuxc {
pinctrl_can1: can1grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
/* CAN1_SR */
MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
>;
};
pinctrl_can2: can2grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
/* CAN2_SR */
MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
>;
};
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000
MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008
MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008
/* CS */
MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008
>;
};
pinctrl_enet: enetgrp {
fsl,pins = <
/* MX6QDL_ENET_PINGRP4 */
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
/* Phy reset */
MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
/* nINTRP */
MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
>;
};
pinctrl_leds: ledsgrp {
fsl,pins = <
/* DEBUG_0 */
MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
/* DEBUG_1 */
MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
/* LED1 (lighttower) */
MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x13070
/* LED2 (lighttower) */
MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x13070
/* LED3 (lighttower) */
MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x13070
/* LED4 (lighttower) */
MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x13070
>;
};
pinctrl_pwm1: pwm1grp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
>;
};
/* YaCO AUX Uart */
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
>;
};
pinctrl_uart2: uart2grp {
fsl,pins = <
MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x130b1
>;
};
pinctrl_uart4: uart4grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
>;
};
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
/* power enable, high active */
MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
>;
};
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
>;
};
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
>;
};
};

446
arch/arm/boot/dts/imx6dl-plym2m.dts Normal file
Просмотреть файл

@ -0,0 +1,446 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Copyright (c) 2014 Protonic Holland
* Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
#include "imx6dl.dtsi"
/ {
model = "Plymovent M2M board";
compatible = "ply,plym2m", "fsl,imx6dl";
chosen {
stdout-path = &uart4;
};
backlight: backlight {
compatible = "pwm-backlight";
pwms = <&pwm1 0 5000000 0>;
brightness-levels = <0 1000>;
num-interpolated-steps = <20>;
default-brightness-level = <19>;
power-supply = <&reg_12v0>;
};
display {
compatible = "fsl,imx-parallel-display";
pinctrl-0 = <&pinctrl_ipu1_disp>;
pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
display_in: endpoint {
remote-endpoint = <&ipu1_di0_disp0>;
};
};
port@1 {
reg = <1>;
display_out: endpoint {
remote-endpoint = <&panel_in>;
};
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_leds>;
led-0 {
label = "debug0";
function = LED_FUNCTION_STATUS;
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
panel {
compatible = "edt,etm0700g0bdh6";
backlight = <&backlight>;
power-supply = <&reg_3v3>;
port {
panel_in: endpoint {
remote-endpoint = <&display_out>;
};
};
};
clk50m_phy: phy-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <50000000>;
};
reg_3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
reg_5v0: regulator-5v0 {
compatible = "regulator-fixed";
regulator-name = "5v0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
reg_12v0: regulator-12v0 {
compatible = "regulator-fixed";
regulator-name = "12v0";
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
};
};
&can1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1>;
xceiver-supply = <&reg_5v0>;
status = "okay";
};
&ecspi1 {
cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <20000000>;
};
};
&ecspi2 {
cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
touchscreen@0 {
compatible = "ti,tsc2046";
reg = <0>;
pinctrl-0 = <&pinctrl_tsc2046>;
pinctrl-names ="default";
spi-max-frequency = <100000>;
interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
touchscreen-size-x = <800>;
touchscreen-size-y = <480>;
touchscreen-inverted-x;
touchscreen-inverted-y;
touchscreen-max-pressure = <4095>;
ti,vref-delay-usecs = /bits/ 16 <100>;
ti,x-plate-ohms = /bits/ 16 <800>;
ti,y-plate-ohms = /bits/ 16 <300>;
wakeup-source;
};
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rmii";
clocks = <&clks IMX6QDL_CLK_ENET>,
<&clks IMX6QDL_CLK_ENET>,
<&clk50m_phy>;
clock-names = "ipg", "ahb", "ptp";
phy-handle = <&rgmii_phy>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
/* Microchip KSZ8081RNA PHY */
rgmii_phy: ethernet-phy@0 {
reg = <0>;
interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
reset-assert-us = <10000>;
reset-deassert-us = <300>;
};
};
};
&gpio1 {
gpio-line-names =
"CAN1_TERM", "SD1_CD", "", "", "", "", "", "",
"DEBUG_0", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "";
};
&gpio2 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "ECSPI2_SS0", "", "", "", "TSC_BUSY", "";
};
&gpio3 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "ECSPI1_SS1", "TSC_PENIRQ", "", "", "",
"", "", "", "", "", "", "", "";
};
&gpio4 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"", "", "", "", "CAN1_SR", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "";
};
&gpio5 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "ETH_RESET", "ETH_INTRP",
"", "", "", "", "", "", "", "";
};
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
/* additional i2c devices are added automatically by the boot loader */
};
&i2c3 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
temperature-sensor@70 {
compatible = "ti,tmp103";
reg = <0x70>;
};
};
&ipu1_di0_disp0 {
remote-endpoint = <&display_in>;
};
&pwm1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
status = "okay";
};
&usbphynop1 {
status = "disabled";
};
&usbphynop2 {
status = "disabled";
};
&usbotg {
phy_type = "utmi";
dr_mode = "host";
disable-over-current;
status = "okay";
};
&usdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc1>;
cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
no-1-8-v;
disable-wp;
cap-sd-highspeed;
no-mmc;
no-sdio;
status = "okay";
};
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
bus-width = <8>;
no-1-8-v;
non-removable;
no-sd;
no-sdio;
status = "okay";
};
&iomuxc {
pinctrl_can1: can1grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
/* CAN1_SR */
MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
/* CAN1_TERM */
MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
>;
};
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000
MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008
MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008
/* CS */
MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008
>;
};
pinctrl_ecspi2: ecspi2grp {
fsl,pins = <
MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x10000
MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x3008
MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x3008
/* CS */
MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x3008
>;
};
pinctrl_enet: enetgrp {
fsl,pins = <
/* MX6QDL_ENET_PINGRP4 */
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
/* Phy reset */
MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
/* nINTRP */
MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
>;
};
pinctrl_ipu1_disp: ipudisp1grp {
fsl,pins = <
/* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30
MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30
MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30
MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30
MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30
MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30
MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30
MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30
MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30
MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30
MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30
MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30
MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30
MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30
MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30
MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30
MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30
MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30
MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30
MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30
MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30
MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30
>;
};
pinctrl_leds: ledsgrp {
fsl,pins = <
MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
>;
};
pinctrl_pwm1: pwm1grp {
fsl,pins = <
MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8
>;
};
pinctrl_tsc2046: tsc2046grp {
fsl,pins = <
/* TSC_PENIRQ */
MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
/* TSC_BUSY */
MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
>;
};
pinctrl_uart4: uart4grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
>;
};
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
>;
};
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
>;
};
};

852
arch/arm/boot/dts/imx6dl-prtmvt.dts Normal file
Просмотреть файл

@ -0,0 +1,852 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Copyright (c) 2016 Protonic Holland
* Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
*/
/dts-v1/;
#include <dt-bindings/display/sdtv-standards.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/media/tvp5150.h>
#include <dt-bindings/sound/fsl-imx-audmux.h>
#include "imx6dl.dtsi"
/ {
model = "Protonic MVT board";
compatible = "prt,prtmvt", "fsl,imx6dl";
chosen {
stdout-path = &uart4;
};
backlight: backlight {
compatible = "pwm-backlight";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_backlight>;
pwms = <&pwm1 0 5000000 0>;
brightness-levels = <0 16 64 255>;
num-interpolated-steps = <16>;
default-brightness-level = <1>;
power-supply = <&reg_3v3>;
enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
};
connector {
compatible = "composite-video-connector";
label = "Composite0";
sdtv-standards = <SDTV_STD_PAL_B>;
port {
comp0_out: endpoint {
remote-endpoint = <&tvp5150_comp0_in>;
};
};
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpiokeys>;
autorepeat;
power {
label = "Power Button";
gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
wakeup-source;
};
f1 {
label = "GPIO Key F1";
linux,code = <KEY_F1>;
gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
};
f2 {
label = "GPIO Key F2";
linux,code = <KEY_F2>;
gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
};
f3 {
label = "GPIO Key F3";
linux,code = <KEY_F3>;
gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
};
f4 {
label = "GPIO Key F4";
linux,code = <KEY_F4>;
gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
};
f5 {
label = "GPIO Key F5";
linux,code = <KEY_F5>;
gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
};
cycle {
label = "GPIO Key CYCLE";
linux,code = <KEY_CYCLEWINDOWS>;
gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
};
esc {
label = "GPIO Key ESC";
linux,code = <KEY_ESC>;
gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
};
up {
label = "GPIO Key UP";
linux,code = <KEY_UP>;
gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
};
down {
label = "GPIO Key DOWN";
linux,code = <KEY_DOWN>;
gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
};
ok {
label = "GPIO Key OK";
linux,code = <KEY_OK>;
gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
};
f6 {
label = "GPIO Key F6";
linux,code = <KEY_F6>;
gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
};
f7 {
label = "GPIO Key F7";
linux,code = <KEY_F7>;
gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
};
f8 {
label = "GPIO Key F8";
linux,code = <KEY_F8>;
gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
};
f9 {
label = "GPIO Key F9";
linux,code = <KEY_F9>;
gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
};
f10 {
label = "GPIO Key F10";
linux,code = <KEY_F10>;
gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_leds>;
led-0 {
label = "debug0";
function = LED_FUNCTION_HEARTBEAT;
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
led-1 {
label = "debug1";
function = LED_FUNCTION_DISK;
gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "disk-activity";
};
led-2 {
label = "power_led";
function = LED_FUNCTION_POWER;
gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
};
panel {
compatible = "kyo,tcg070wvlq", "lg,lb070wv8";
backlight = <&backlight>;
power-supply = <&reg_3v3>;
port {
panel_in: endpoint {
remote-endpoint = <&lvds0_out>;
};
};
};
clk50m_phy: phy-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <50000000>;
};
reg_1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
reg_3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
reg_h1_vbus: regulator-h1-vbus {
compatible = "regulator-fixed";
regulator-name = "h1-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
reg_otg_vbus: regulator-otg-vbus {
compatible = "regulator-fixed";
regulator-name = "otg-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
sound {
compatible = "simple-audio-card";
simple-audio-card,name = "prti6q-sgtl5000";
simple-audio-card,format = "i2s";
simple-audio-card,widgets =
"Microphone", "Microphone Jack",
"Line", "Line In Jack",
"Headphone", "Headphone Jack",
"Speaker", "External Speaker";
simple-audio-card,routing =
"MIC_IN", "Microphone Jack",
"LINE_IN", "Line In Jack",
"Headphone Jack", "HP_OUT",
"External Speaker", "LINE_OUT";
simple-audio-card,cpu {
sound-dai = <&ssi1>;
system-clock-frequency = <0>;
};
simple-audio-card,codec {
sound-dai = <&codec>;
bitclock-master;
frame-master;
};
};
};
&audmux {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_audmux>;
status = "okay";
mux-ssi1 {
fsl,audmux-port = <0>;
fsl,port-config = <
IMX_AUDMUX_V2_PTCR_SYN 0
IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
IMX_AUDMUX_V2_PTCR_TFSDIR 0
IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
>;
};
mux-pins3 {
fsl,audmux-port = <2>;
fsl,port-config = <
IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
0 IMX_AUDMUX_V2_PDCR_TXRXEN
>;
};
};
&can1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1>;
status = "okay";
};
&can2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can2>;
status = "okay";
};
&clks {
assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
};
&ecspi1 {
cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <20000000>;
};
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rmii";
clocks = <&clks IMX6QDL_CLK_ENET>,
<&clks IMX6QDL_CLK_ENET>,
<&clk50m_phy>;
clock-names = "ipg", "ahb", "ptp";
phy-handle = <&rmii_phy>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
/* Microchip KSZ8081RNA PHY */
rmii_phy: ethernet-phy@0 {
reg = <0>;
interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
reset-assert-us = <10000>;
reset-deassert-us = <3000>;
};
};
};
&gpio1 {
gpio-line-names =
"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
"CAM2_MIRROR", "", "", "SMBALERT",
"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
"SD1_DATA3", "", "",
"", "", "", "", "", "", "", "";
};
&gpio2 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
"", "", "", "", "", "", "", "ON_SWITCH",
"POWER_LED", "", "", "", "", "", "", "";
};
&gpio3 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
"CPU_ON1_FB", "USB_EXT1_OC", "USB_EXT1_PWR", "YACO_IRQ",
"TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
"YACO_RESET";
};
&gpio4 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"", "", "", "", "CAN1_SR", "CAN2_SR", "CAN2_TX", "CAN2_RX",
"", "", "DIP1_FB", "", "", "", "", "",
"CPU_LIGHT_ON", "", "ETH_RESET", "", "BL_EN",
"BL_PWM", "ETH_INTRP", "";
};
&gpio5 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
};
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
codec: audio-codec@a {
compatible = "fsl,sgtl5000";
reg = <0xa>;
#sound-dai-cells = <0>;
clocks = <&clks 201>;
VDDA-supply = <&reg_3v3>;
VDDIO-supply = <&reg_3v3>;
VDDD-supply = <&reg_1v8>;
};
video@5c {
compatible = "ti,tvp5150";
reg = <0x5c>;
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
tvp5150_comp0_in: endpoint {
remote-endpoint = <&comp0_out>;
};
};
/* Output port 2 is video output pad */
port@2 {
reg = <2>;
tvp5151_to_ipu1_csi0_mux: endpoint {
remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
};
};
};
gpio_pca: gpio@74 {
compatible = "nxp,pca9539";
reg = <0x74>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pca9539>;
interrupt-parent = <&gpio4>;
interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
gpio-controller;
#gpio-cells = <2>;
};
/* additional i2c devices are added automatically by the boot loader */
};
&i2c3 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
adc@49 {
compatible = "ti,ads1015";
reg = <0x49>;
#address-cells = <1>;
#size-cells = <0>;
channel@4 {
reg = <4>;
ti,gain = <3>;
ti,datarate = <3>;
};
channel@5 {
reg = <5>;
ti,gain = <3>;
ti,datarate = <3>;
};
channel@6 {
reg = <6>;
ti,gain = <3>;
ti,datarate = <3>;
};
channel@7 {
reg = <7>;
ti,gain = <3>;
ti,datarate = <3>;
};
};
rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
};
temperature-sensor@70 {
compatible = "ti,tmp103";
reg = <0x70>;
};
};
&ipu1_csi0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ipu1_csi0>;
status = "okay";
};
&ipu1_csi0_mux_from_parallel_sensor {
remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
};
&ldb {
status = "okay";
lvds-channel@0 {
status = "okay";
port@4 {
reg = <4>;
lvds0_out: endpoint {
remote-endpoint = <&panel_in>;
};
};
};
};
&pcie {
status = "okay";
};
&pwm1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
};
&ssi1 {
#sound-dai-cells = <0>;
fsl,mode = "ac97-slave";
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
status = "okay";
};
&uart5 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart5>;
status = "okay";
};
&usbh1 {
vbus-supply = <&reg_h1_vbus>;
pinctrl-names = "default";
phy_type = "utmi";
dr_mode = "host";
status = "okay";
};
&usbotg {
vbus-supply = <&reg_otg_vbus>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
phy_type = "utmi";
dr_mode = "host";
disable-over-current;
status = "okay";
};
&usdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc1>;
cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
no-1-8-v;
disable-wp;
cap-sd-highspeed;
no-mmc;
no-sdio;
status = "okay";
};
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
bus-width = <8>;
no-1-8-v;
non-removable;
no-sd;
no-sdio;
status = "okay";
};
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
pinctrl_audmux: audmuxgrp {
fsl,pins = <
/* SGTL5000 sys_mclk */
MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
>;
};
pinctrl_backlight: backlightgrp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
>;
};
pinctrl_can1: can1grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
/* CAN1_SR */
MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
/* CAN1_TERM */
MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
>;
};
pinctrl_can2: can2grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
/* CAN2_SR */
MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
>;
};
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
/* CS */
MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
>;
};
pinctrl_enet: enetgrp {
fsl,pins = <
/* MX6QDL_ENET_PINGRP4 */
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
/* Phy reset */
MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
/* nINTRP */
MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
>;
};
pinctrl_gpiokeys: gpiokeygrp {
fsl,pins = <
/* nON_SWITCH */
MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
>;
};
pinctrl_hog: hoggrp {
fsl,pins = <
/* ITU656_nRESET */
MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
/* CAM1_MIRROR */
MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
/* CAM2_MIRROR */
MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
/* CAM_nDETECT */
MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
/* ISB_IN1 */
MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
/* ISB_nIN2 */
MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0
/* WARN_LIGHT */
MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0
/* ON2_FB */
MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0
/* YACO_nIRQ */
MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0
/* YACO_BOOT0 */
MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0
/* YACO_nRESET */
MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
/* FORCE_ON1 */
MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
/* AUDIO_nRESET */
MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
/* ITU656_nPDN */
MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
/* HW revision detect */
/* REV_ID0 */
MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
/* REV_ID1 */
MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
/* REV_ID2 */
MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
/* REV_ID3 */
MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
/* REV_ID4 */
MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
/* New in HW revision 1 */
/* ON1_FB */
MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0
/* DIP1_FB */
MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
>;
};
pinctrl_ipu1_csi0: ipu1csi0grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
>;
};
pinctrl_leds: ledsgrp {
fsl,pins = <
/* DEBUG0 */
MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
/* DEBUG1 */
MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
/* POWER_LED */
MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
>;
};
pinctrl_pca9539: pca9539 {
fsl,pins = <
MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
>;
};
pinctrl_pwm1: pwm1grp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
>;
};
/* YaCO AUX Uart */
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
>;
};
pinctrl_uart2: uart2grp {
fsl,pins = <
MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
>;
};
/* YaCO Touchscreen UART */
pinctrl_uart3: uart3grp {
fsl,pins = <
MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
>;
};
pinctrl_uart4: uart4grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
>;
};
pinctrl_uart5: uart5grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
>;
};
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
/* power enable, high active */
MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
>;
};
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
>;
};
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
>;
};
};

852
arch/arm/boot/dts/imx6dl-victgo.dts Normal file
Просмотреть файл

@ -0,0 +1,852 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Copyright (c) 2016 Protonic Holland
* Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
*/
/dts-v1/;
#include <dt-bindings/display/sdtv-standards.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/media/tvp5150.h>
#include <dt-bindings/sound/fsl-imx-audmux.h>
#include "imx6dl.dtsi"
/ {
model = "Kverneland TGO";
compatible = "kvg,victgo", "fsl,imx6dl";
chosen {
stdout-path = &uart4;
};
backlight: backlight {
compatible = "pwm-backlight";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_backlight>;
pwms = <&pwm1 0 5000000 0>;
brightness-levels = <0 16 64 255>;
num-interpolated-steps = <16>;
default-brightness-level = <1>;
power-supply = <&reg_3v3>;
enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
};
connector {
compatible = "composite-video-connector";
label = "Composite0";
sdtv-standards = <SDTV_STD_PAL_B>;
port {
comp0_out: endpoint {
remote-endpoint = <&tvp5150_comp0_in>;
};
};
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpiokeys>;
autorepeat;
power {
label = "Power Button";
gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
wakeup-source;
};
enter {
label = "Rotary Key";
gpios = <&gpio2 05 GPIO_ACTIVE_LOW>;
linux,code = <KEY_ENTER>;
wakeup-source;
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_leds>;
led-0 {
label = "debug0";
function = LED_FUNCTION_HEARTBEAT;
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
led-1 {
label = "debug1";
function = LED_FUNCTION_DISK;
gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "disk-activity";
};
led-2 {
label = "power_led";
function = LED_FUNCTION_POWER;
gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
};
panel {
compatible = "kyo,tcg121xglp";
backlight = <&backlight>;
power-supply = <&reg_3v3>;
port {
panel_in: endpoint {
remote-endpoint = <&lvds0_out>;
};
};
};
clk50m_phy: phy-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <50000000>;
};
reg_1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
reg_3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
reg_h1_vbus: regulator-h1-vbus {
compatible = "regulator-fixed";
regulator-name = "h1-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
reg_otg_vbus: regulator-otg-vbus {
compatible = "regulator-fixed";
regulator-name = "otg-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
rotary-encoder {
compatible = "rotary-encoder";
pinctrl-0 = <&pinctrl_rotary_ch>;
gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>,
<&gpio2 4 GPIO_ACTIVE_HIGH>;
linux,axis = <REL_WHEEL>;
rotary-encoder,steps-per-period = <4>;
rotary-encoder,relative-axis;
rotary-encoder,rollover;
wakeup-source;
};
sound {
compatible = "simple-audio-card";
simple-audio-card,name = "prti6q-sgtl5000";
simple-audio-card,format = "i2s";
simple-audio-card,widgets =
"Microphone", "Microphone Jack",
"Line", "Line In Jack",
"Headphone", "Headphone Jack",
"Speaker", "External Speaker";
simple-audio-card,routing =
"MIC_IN", "Microphone Jack",
"LINE_IN", "Line In Jack",
"Headphone Jack", "HP_OUT",
"External Speaker", "LINE_OUT";
simple-audio-card,cpu {
sound-dai = <&ssi1>;
system-clock-frequency = <0>;
};
simple-audio-card,codec {
sound-dai = <&codec>;
bitclock-master;
frame-master;
};
};
};
&audmux {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_audmux>;
status = "okay";
mux-ssi1 {
fsl,audmux-port = <0>;
fsl,port-config = <
IMX_AUDMUX_V2_PTCR_SYN 0
IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
IMX_AUDMUX_V2_PTCR_TFSDIR 0
IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
>;
};
mux-pins3 {
fsl,audmux-port = <2>;
fsl,port-config = <
IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
0 IMX_AUDMUX_V2_PDCR_TXRXEN
>;
};
};
&can1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1>;
status = "okay";
};
&can2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can2>;
status = "okay";
};
&clks {
assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
};
&ecspi1 {
cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <20000000>;
};
};
&ecspi2 {
cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
touchscreen@0 {
compatible = "ti,tsc2046";
reg = <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_touchscreen>;
spi-max-frequency = <200000>;
interrupts-extended = <&gpio5 8 IRQ_TYPE_EDGE_FALLING>;
pendown-gpio = <&gpio5 8 GPIO_ACTIVE_LOW>;
touchscreen-size-x = <800>;
touchscreen-size-y = <480>;
touchscreen-inverted-y;
touchscreen-max-pressure = <4095>;
ti,vref-delay-usecs = /bits/ 16 <100>;
ti,x-plate-ohms = /bits/ 16 <800>;
ti,y-plate-ohms = /bits/ 16 <300>;
wakeup-source;
};
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rmii";
clocks = <&clks IMX6QDL_CLK_ENET>,
<&clks IMX6QDL_CLK_ENET>,
<&clk50m_phy>;
clock-names = "ipg", "ahb", "ptp";
phy-handle = <&rmii_phy>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
/* Microchip KSZ8081RNA PHY */
rmii_phy: ethernet-phy@0 {
reg = <0>;
interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
reset-assert-us = <10000>;
reset-deassert-us = <300>;
};
};
};
&gpio1 {
gpio-line-names =
"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
"CAM2_MIRROR", "", "", "SMBALERT",
"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
"SD1_DATA3", "", "",
"", "", "", "", "", "", "", "";
};
&gpio2 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
"", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
"POWER_LED", "", "", "", "", "", "", "";
};
&gpio3 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
"CPU_ON1_FB", "USB_EXT1_OC", "USB_EXT1_PWR", "YACO_IRQ",
"TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
"YACO_RESET";
};
&gpio4 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"", "", "", "", "CAN1_SR", "CAN2_SR", "CAN2_TX", "CAN2_RX",
"", "", "DIP1_FB", "", "VCAM_EN", "", "", "",
"CPU_LIGHT_ON", "", "ETH_RESET", "CPU_CONTACT_IN", "BL_EN",
"BL_PWM", "ETH_INTRP", "ISB_LED";
};
&gpio5 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"TSC_PENIRQ", "TSC_BUSY", "ECSPI2_MOSI", "ECSPI2_MISO",
"ECSPI2_SS0", "ECSPI2_SCLK", "", "",
"", "", "", "", "", "", "", "",
"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
};
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
codec: audio-codec@a {
compatible = "fsl,sgtl5000";
reg = <0xa>;
#sound-dai-cells = <0>;
clocks = <&clks 201>;
VDDA-supply = <&reg_3v3>;
VDDIO-supply = <&reg_3v3>;
VDDD-supply = <&reg_1v8>;
};
video-decoder@5c {
compatible = "ti,tvp5150";
reg = <0x5c>;
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
tvp5150_comp0_in: endpoint {
remote-endpoint = <&comp0_out>;
};
};
/* Output port 2 is video output pad */
port@2 {
reg = <2>;
tvp5151_to_ipu1_csi0_mux: endpoint {
remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
};
};
};
keypad@70 {
compatible = "holtek,ht16k33";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_keypad>;
reg = <0x70>;
refresh-rate-hz = <20>;
debounce-delay-ms = <50>;
interrupts-extended = <&gpio4 5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>;
keypad,num-rows = <12>;
keypad,num-columns = <3>;
linux,keymap = <
MATRIX_KEY(2, 0, KEY_F6)
MATRIX_KEY(3, 0, KEY_F8)
MATRIX_KEY(4, 0, KEY_F10)
MATRIX_KEY(5, 0, KEY_F4)
MATRIX_KEY(6, 0, KEY_F2)
MATRIX_KEY(2, 1, KEY_F5)
MATRIX_KEY(3, 1, KEY_F7)
MATRIX_KEY(4, 1, KEY_F9)
MATRIX_KEY(5, 1, KEY_F3)
MATRIX_KEY(6, 1, KEY_F1)
>;
};
/* additional i2c devices are added automatically by the boot loader */
};
&i2c3 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
adc@49 {
compatible = "ti,ads1015";
reg = <0x49>;
#address-cells = <1>;
#size-cells = <0>;
channel@4 {
reg = <4>;
ti,gain = <3>;
ti,datarate = <3>;
};
channel@5 {
reg = <5>;
ti,gain = <3>;
ti,datarate = <3>;
};
channel@6 {
reg = <6>;
ti,gain = <3>;
ti,datarate = <3>;
};
channel@7 {
reg = <7>;
ti,gain = <3>;
ti,datarate = <3>;
};
};
rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
};
temperature-sensor@70 {
compatible = "ti,tmp103";
reg = <0x70>;
};
};
&ipu1_csi0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ipu1_csi0>;
status = "okay";
};
&ipu1_csi0_mux_from_parallel_sensor {
remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
};
&ldb {
status = "okay";
lvds-channel@0 {
status = "okay";
port@4 {
reg = <4>;
lvds0_out: endpoint {
remote-endpoint = <&panel_in>;
};
};
};
};
&pwm1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
};
&pwm3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm3>;
status = "okay";
};
&ssi1 {
#sound-dai-cells = <0>;
fsl,mode = "ac97-slave";
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
status = "okay";
};
&uart5 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart5>;
status = "okay";
};
&usbh1 {
vbus-supply = <&reg_h1_vbus>;
pinctrl-names = "default";
phy_type = "utmi";
dr_mode = "host";
status = "okay";
};
&usbotg {
vbus-supply = <&reg_otg_vbus>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
phy_type = "utmi";
dr_mode = "host";
disable-over-current;
status = "okay";
};
&usdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc1>;
cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
no-1-8-v;
disable-wp;
cap-sd-highspeed;
no-mmc;
no-sdio;
status = "okay";
};
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
bus-width = <8>;
no-1-8-v;
non-removable;
no-sd;
no-sdio;
status = "okay";
};
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
pinctrl_audmux: audmuxgrp {
fsl,pins = <
/* SGTL5000 sys_mclk */
MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
>;
};
pinctrl_backlight: backlightgrp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
>;
};
pinctrl_can1: can1grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
/* CAN1_SR */
MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
/* CAN1_TERM */
MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
>;
};
pinctrl_can2: can2grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
/* CAN2_SR */
MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
>;
};
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
/* CS */
MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
>;
};
pinctrl_ecspi2: ecspi2grp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI 0x100b1
MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO 0x100b1
MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1
MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK 0x100b1
>;
};
pinctrl_enet: enetgrp {
fsl,pins = <
/* MX6QDL_ENET_PINGRP4 */
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
/* Phy reset */
MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
/* nINTRP */
MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
>;
};
pinctrl_gpiokeys: gpiokeygrp {
fsl,pins = <
/* ROTARY_BTN */
MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x1b0b0
/* nON_SWITCH */
MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
>;
};
pinctrl_hog: hoggrp {
fsl,pins = <
/* ITU656_nRESET */
MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
/* CAM1_MIRROR */
MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
/* CAM2_MIRROR */
MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
/* CAM_nDETECT */
MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
/* ISB_IN1 */
MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
/* ISB_nIN2 */
MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0
/* WARN_LIGHT */
MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0
/* ON2_FB */
MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0
/* YACO_nIRQ */
MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0
/* YACO_BOOT0 */
MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0
/* YACO_nRESET */
MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
/* FORCE_ON1 */
MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
/* AUDIO_nRESET */
MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
/* ITU656_nPDN */
MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
/* HW revision detect */
/* REV_ID0 */
MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
/* REV_ID1 is shared with PWM3 */
/* REV_ID2 */
MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
/* REV_ID3 */
MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
/* REV_ID4 */
MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
/* New in HW revision 1 */
/* ON1_FB */
MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0
/* DIP1_FB */
MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
>;
};
pinctrl_ipu1_csi0: ipu1csi0grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
>;
};
pinctrl_keypad: keypadgrp {
fsl,pins = <
MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
>;
};
pinctrl_leds: ledsgrp {
fsl,pins = <
/* DEBUG0 */
MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
/* DEBUG1 */
MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
/* POWER_LED */
MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
>;
};
pinctrl_pwm1: pwm1grp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
>;
};
pinctrl_pwm3: pwm3grp {
fsl,pins = <
MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b0
>;
};
pinctrl_rotary_ch: rotarychgrp {
fsl,pins = <
MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0
>;
};
pinctrl_touchscreen: touchscreengrp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x1b0b0
MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x1b0b0
>;
};
/* YaCO AUX Uart */
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
>;
};
pinctrl_uart2: uart2grp {
fsl,pins = <
MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
>;
};
/* YaCO Touchscreen UART */
pinctrl_uart3: uart3grp {
fsl,pins = <
MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
>;
};
pinctrl_uart4: uart4grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
>;
};
pinctrl_uart5: uart5grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
>;
};
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
/* power enable, high active */
MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
>;
};
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
>;
};
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
>;
};
};

13
arch/arm/boot/dts/imx6dl-vicut1.dts Normal file
Просмотреть файл

@ -0,0 +1,13 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Copyright (c) 2014 Protonic Holland
*/
/dts-v1/;
#include "imx6dl.dtsi"
#include "imx6qdl-vicut1.dtsi"
/ {
model = "Kverneland UT1 Board";
compatible = "kvg,vicut1", "fsl,imx6dl";
};

7
arch/arm/boot/dts/imx6q-tbs2910.dts
Просмотреть файл

@ -16,6 +16,13 @@
stdout-path = &uart1;
};
aliases {
mmc0 = &usdhc2;
mmc1 = &usdhc3;
mmc2 = &usdhc4;
/delete-property/ mmc3;
};
memory@10000000 {
device_type = "memory";
reg = <0x10000000 0x80000000>;

17
arch/arm/boot/dts/imx6q-vicut1.dts Normal file
Просмотреть файл

@ -0,0 +1,17 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Copyright (c) 2014 Protonic Holland
*/
/dts-v1/;
#include "imx6q.dtsi"
#include "imx6qdl-vicut1.dtsi"
/ {
model = "Kverneland UT1Q Board";
compatible = "kvg,vicut1q", "fsl,imx6q";
};
&sata {
status = "okay";
};

20
arch/arm/boot/dts/imx6q.dtsi
Просмотреть файл

@ -406,19 +406,21 @@
&hdmi {
compatible = "fsl,imx6q-hdmi";
port@2 {
reg = <2>;
ports {
port@2 {
reg = <2>;
hdmi_mux_2: endpoint {
remote-endpoint = <&ipu2_di0_hdmi>;
hdmi_mux_2: endpoint {
remote-endpoint = <&ipu2_di0_hdmi>;
};
};
};
port@3 {
reg = <3>;
port@3 {
reg = <3>;
hdmi_mux_3: endpoint {
remote-endpoint = <&ipu2_di1_hdmi>;
hdmi_mux_3: endpoint {
remote-endpoint = <&ipu2_di1_hdmi>;
};
};
};
};

2
arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
Просмотреть файл

@ -418,7 +418,7 @@
/* VDD_AUD_1P8: Audio codec */
reg_aud_1p8v: ldo3 {
regulator-name = "vdd1p8";
regulator-name = "vdd1p8a";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;

6
arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi
Просмотреть файл

@ -137,7 +137,7 @@
lcd_backlight: lcd-backlight {
compatible = "pwm-backlight";
pwms = <&pwm4 0 5000000>;
pwms = <&pwm4 0 5000000 0>;
pwm-names = "LCD_BKLT_PWM";
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
@ -167,7 +167,7 @@
i2c-gpio,delay-us = <2>; /* ~100 kHz */
#address-cells = <1>;
#size-cells = <0>;
status = "disabld";
status = "disabled";
};
i2c_cam: i2c-gpio-cam {
@ -179,7 +179,7 @@
i2c-gpio,delay-us = <2>; /* ~100 kHz */
#address-cells = <1>;
#size-cells = <0>;
status = "disabld";
status = "disabled";
};
};

1
arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
Просмотреть файл

@ -298,6 +298,7 @@
interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
<&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
fsl,err006687-workaround-present;
fsl,magic-packet;
status = "okay";
};

14
arch/arm/boot/dts/imx6qdl-sr-som.dtsi
Просмотреть файл

@ -53,7 +53,6 @@
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
phy-handle = <&phy>;
phy-mode = "rgmii-id";
phy-reset-duration = <2>;
phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
@ -63,9 +62,20 @@
#address-cells = <1>;
#size-cells = <0>;
phy: ethernet-phy@0 {
/*
* The PHY can appear at either address 0 or 4 due to the
* configuration (LED) pin not being pulled sufficiently.
*/
ethernet-phy@0 {
reg = <0>;
qca,clk-out-frequency = <125000000>;
qca,smarteee-tw-us-1g = <24>;
};
ethernet-phy@4 {
reg = <4>;
qca,clk-out-frequency = <125000000>;
qca,smarteee-tw-us-1g = <24>;
};
};
};

803
arch/arm/boot/dts/imx6qdl-vicut1.dtsi Normal file
Просмотреть файл

@ -0,0 +1,803 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Copyright (c) 2014 Protonic Holland
* Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
*/
#include <dt-bindings/display/sdtv-standards.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/media/tvp5150.h>
#include <dt-bindings/sound/fsl-imx-audmux.h>
/ {
chosen {
stdout-path = &uart4;
};
backlight: backlight {
compatible = "pwm-backlight";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_backlight>;
pwms = <&pwm1 0 5000000 0>;
brightness-levels = <0 16 64 255>;
num-interpolated-steps = <16>;
default-brightness-level = <1>;
power-supply = <&reg_3v3>;
enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
};
connector {
compatible = "composite-video-connector";
label = "Composite0";
sdtv-standards = <SDTV_STD_PAL_B>;
port {
comp0_out: endpoint {
remote-endpoint = <&tvp5150_comp0_in>;
};
};
};
gpio-keys {
compatible = "gpio-keys";
autorepeat;
power {
label = "Power Button";
gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
wakeup-source;
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_leds>;
led-0 {
label = "LED_DI0_DEBUG_0";
function = LED_FUNCTION_HEARTBEAT;
gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
led-1 {
label = "LED_DI0_DEBUG_1";
function = LED_FUNCTION_DISK;
gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "disk-activity";
};
led-2 {
label = "POWER_LED";
function = LED_FUNCTION_POWER;
gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
};
panel {
compatible = "kyo,tcg121xglp";
backlight = <&backlight>;
power-supply = <&reg_3v3>;
port {
panel_in: endpoint {
remote-endpoint = <&lvds0_out>;
};
};
};
reg_1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
reg_3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
reg_h1_vbus: regulator-h1-vbus {
compatible = "regulator-fixed";
regulator-name = "h1-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
reg_otg_vbus: regulator-otg-vbus {
compatible = "regulator-fixed";
regulator-name = "otg-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
reg_wifi: regulator-wifi {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_wifi_npd>;
regulator-name = "wifi";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
enable-active-high;
startup-delay-us = <70000>;
};
sound {
compatible = "simple-audio-card";
simple-audio-card,name = "prti6q-sgtl5000";
simple-audio-card,format = "i2s";
simple-audio-card,widgets =
"Microphone", "Microphone Jack",
"Line", "Line In Jack",
"Headphone", "Headphone Jack",
"Speaker", "External Speaker";
simple-audio-card,routing =
"MIC_IN", "Microphone Jack",
"LINE_IN", "Line In Jack",
"Headphone Jack", "HP_OUT",
"External Speaker", "LINE_OUT";
simple-audio-card,cpu {
sound-dai = <&ssi1>;
system-clock-frequency = <0>; /* Do NOT call fsl_ssi_set_dai_sysclk! */
};
simple-audio-card,codec {
sound-dai = <&codec>;
bitclock-master;
frame-master;
};
};
};
&audmux {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_audmux>;
status = "okay";
mux-ssi1 {
fsl,audmux-port = <0>;
fsl,port-config = <
IMX_AUDMUX_V2_PTCR_SYN 0
IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
IMX_AUDMUX_V2_PTCR_TFSDIR 0
IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
>;
};
mux-pins3 {
fsl,audmux-port = <2>;
fsl,port-config = <
IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
0 IMX_AUDMUX_V2_PDCR_TXRXEN
>;
};
};
&can1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1>;
status = "okay";
};
&can2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can2>;
status = "okay";
};
&clks {
assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
};
&ecspi1 {
cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <20000000>;
};
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii-id";
phy-handle = <&rgmii_phy>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
/* Microchip KSZ9031RNX PHY */
rgmii_phy: ethernet-phy@0 {
reg = <0>;
interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
reset-assert-us = <10000>;
reset-deassert-us = <300>;
};
};
};
&gpio1 {
gpio-line-names =
"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
"CAM2_MIRROR", "", "", "SMBALERT",
"DEBUG_0", "DEBUG_1", "SDIO_SCK", "SDIO_CMD", "SDIO_D3",
"SDIO_D2", "SDIO_D1", "SDIO_D0",
"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
"SD1_DATA3", "", "",
"", "ETH_RESET", "WIFI_PD", "WIFI_BT_RST", "ETH_INT", "",
"WL_IRQ", "ETH_MDC";
};
&gpio2 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
"", "", "", "", "", "", "", "ON_SWITCH",
"POWER_LED", "", "ECSPI2_SS0", "", "", "", "", "";
};
&gpio3 {
gpio-line-names =
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
"CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
"", "", "", "", "", "", "", "";
};
&gpio4 {
gpio-line-names =
"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
"CAN2_SR", "CAN2_TX", "CAN2_RX",
"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "", "", "", "", "", "",
"", "", "", "", "BL_EN", "BL_PWM", "", "";
};
&gpio5 {
gpio-line-names =
"", "", "", "", "", "PCIE_WAKE", "PCIE_CLKREQ", "PCIE_W_DIS",
"PCIE_RESET", "", "", "", "", "", "", "",
"", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
"I2S_BITCLK", "I2S_DOUT",
"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
};
&gpio6 {
gpio-line-names =
"ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
"ITU656_D6", "ITU656_D7", "", "",
"", "", "", "", "", "", "", "",
"", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
"RGMII_TD3",
"RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
"RGMII_RD2", "RGMII_RD3", "", "";
};
&gpio7 {
gpio-line-names =
"EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
"EMMC_DAT1", "EMMC_DAT2", "EMMC_DAT3",
"EMMC_RST", "", "", "", "CAM_DETECT", "", "", "",
"", "EMMC_DAT7", "EMMC_DAT6", "", "", "", "", "",
"", "", "", "", "", "", "", "";
};
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
codec: audio-codec@a {
compatible = "fsl,sgtl5000";
reg = <0xa>;
#sound-dai-cells = <0>;
clocks = <&clks 201>;
VDDA-supply = <&reg_3v3>;
VDDIO-supply = <&reg_3v3>;
VDDD-supply = <&reg_1v8>;
};
video-decoder@5c {
compatible = "ti,tvp5150";
reg = <0x5c>;
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
tvp5150_comp0_in: endpoint {
remote-endpoint = <&comp0_out>;
};
};
/* Output port 2 is video output pad */
port@2 {
reg = <2>;
tvp5151_to_ipu1_csi0_mux: endpoint {
remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
};
};
};
};
&i2c3 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
adc@49 {
compatible = "ti,ads1015";
reg = <0x49>;
#address-cells = <1>;
#size-cells = <0>;
channel@4 {
reg = <4>;
ti,gain = <3>;
ti,datarate = <3>;
};
channel@5 {
reg = <5>;
ti,gain = <3>;
ti,datarate = <3>;
};
channel@6 {
reg = <6>;
ti,gain = <3>;
ti,datarate = <3>;
};
channel@7 {
reg = <7>;
ti,gain = <3>;
ti,datarate = <3>;
};
};
rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
};
temperature-sensor@70 {
compatible = "ti,tmp103";
reg = <0x70>;
};
};
&ipu1_csi0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ipu1_csi0>;
status = "okay";
};
&ipu1_csi0_mux_from_parallel_sensor {
remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
};
&ldb {
status = "okay";
lvds-channel@0 {
status = "okay";
port@4 {
reg = <4>;
lvds0_out: endpoint {
remote-endpoint = <&panel_in>;
};
};
};
};
&pcie {
status = "okay";
};
&pwm1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
};
&ssi1 {
#sound-dai-cells = <0>;
fsl,mode = "ac97-slave";
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
status = "okay";
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
status = "okay";
};
&uart5 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart5>;
status = "okay";
};
&usbh1 {
vbus-supply = <&reg_h1_vbus>;
pinctrl-names = "default";
phy_type = "utmi";
dr_mode = "host";
status = "okay";
};
&usbotg {
vbus-supply = <&reg_otg_vbus>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
phy_type = "utmi";
dr_mode = "host";
disable-over-current;
status = "okay";
};
&usdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc1>;
cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
no-1-8-v;
disable-wp;
cap-sd-highspeed;
no-mmc;
no-sdio;
status = "okay";
};
&usdhc2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc2>;
vmmc-supply = <&reg_wifi>;
non-removable;
cap-power-off-card;
keep-power-in-suspend;
no-1-8-v;
no-mmc;
no-sd;
status = "okay";
wifi {
compatible = "ti,wl1271";
interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
ref-clock-frequency = "38400000";
tcxo-clock-frequency = "19200000";
};
};
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
bus-width = <8>;
no-1-8-v;
non-removable;
no-sd;
no-sdio;
status = "okay";
};
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
pinctrl_audmux: audmuxgrp {
fsl,pins = <
/* SGTL5000 sys_mclk */
MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
>;
};
pinctrl_backlight: backlightgrp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
>;
};
pinctrl_can1: can1grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000
MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008
/* CAN1_SR */
MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008
/* CAN1_TERM */
MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088
>;
};
pinctrl_can2: can2grp {
fsl,pins = <
MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000
MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008
/* CAN2_SR */
MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008
>;
};
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
/* CS */
MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
>;
};
pinctrl_enet: enetgrp {
fsl,pins = <
MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
/* Phy reset */
MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
>;
};
pinctrl_hog: hoggrp {
fsl,pins = <
/* ITU656_nRESET */
MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
/* CAM1_MIRROR */
MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
/* CAM2_MIRROR */
MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
/* CAM_nDETECT */
MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
/* nON_SWITCH */
MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
/* ISB_IN1 */
MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
/* ISB_nIN2 */
MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0
/* WARN_LIGHT */
MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0
/* ON2_FB */
MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0
/* YACO_nIRQ */
MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0
/* YACO_BOOT0 */
MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0
/* YACO_nRESET */
MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
/* FORCE_ON1 */
MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
/* AUDIO_nRESET */
MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
/* ITU656_nPDN */
MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
/* HW revision detect */
/* REV_ID0 */
MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
/* REV_ID1 */
MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
/* REV_ID2 */
MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
/* REV_ID3 */
MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
/* REV_ID4 */
MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
/* New in HW revision 1 */
/* ON1_FB */
MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0
/* DIP1_FB */
MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0
/* New in UT2: FIXME: ISB PWM should start off, PD */
/* ISB_LED_PWM */
MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x130b0
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
>;
};
pinctrl_ipu1_csi0: ipu1csi0grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
>;
};
pinctrl_leds: ledsgrp {
fsl,pins = <
/* DEBUG0 */
MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
/* DEBUG1 */
MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
/* POWER_LED */
MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
>;
};
pinctrl_pwm1: pwm1grp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
>;
};
/* YaCO AUX Uart */
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
>;
};
pinctrl_uart2: uart2grp {
fsl,pins = <
MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
>;
};
/* YaCO Touchscreen UART */
pinctrl_uart3: uart3grp {
fsl,pins = <
MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
>;
};
pinctrl_uart4: uart4grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
>;
};
pinctrl_uart5: uart5grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
>;
};
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
/* power enable, high active */
MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
>;
};
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
>;
};
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
/* WL12xx IRQ */
MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
>;
};
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
>;
};
pinctrl_wifi_npd: wifinpdgrp {
fsl,pins = <
MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
>;
};
};

42
arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
Просмотреть файл

@ -112,17 +112,17 @@
sound1 {
compatible = "simple-audio-card";
simple-audio-card,name = "Front";
simple-audio-card,name = "front";
simple-audio-card,format = "i2s";
simple-audio-card,bitclock-master = <&sound1_codec>;
simple-audio-card,frame-master = <&sound1_codec>;
simple-audio-card,widgets =
"Headphone", "Headphone Jack";
simple-audio-card,routing =
"Headphone Jack", "HPLEFT",
"Headphone Jack", "HPRIGHT",
"LEFTIN", "HPL",
"RIGHTIN", "HPR";
"Headphone Jack", "HPA1 HPLEFT",
"Headphone Jack", "HPA1 HPRIGHT",
"HPA1 LEFTIN", "HPL",
"HPA1 RIGHTIN", "HPR";
simple-audio-card,aux-devs = <&hpa1>;
sound1_cpu: simple-audio-card,cpu {
@ -137,17 +137,17 @@
sound2 {
compatible = "simple-audio-card";
simple-audio-card,name = "Back";
simple-audio-card,name = "periph";
simple-audio-card,format = "i2s";
simple-audio-card,bitclock-master = <&sound2_codec>;
simple-audio-card,frame-master = <&sound2_codec>;
simple-audio-card,widgets =
"Headphone", "Headphone Jack";
simple-audio-card,routing =
"Headphone Jack", "HPLEFT",
"Headphone Jack", "HPRIGHT",
"LEFTIN", "HPL",
"RIGHTIN", "HPR";
"Headphone Jack", "HPA1 HPLEFT",
"Headphone Jack", "HPA1 HPRIGHT",
"HPA1 LEFTIN", "HPL",
"HPA1 RIGHTIN", "HPR";
simple-audio-card,aux-devs = <&hpa2>;
sound2_cpu: simple-audio-card,cpu {
@ -399,6 +399,7 @@
reg = <0x60>;
power-gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
Vdd-supply = <&reg_5p0v_main>;
sound-name-prefix = "HPA1";
};
edp-bridge@68 {
@ -598,6 +599,8 @@
touchscreen-inverted-x;
touchscreen-swapped-x-y;
syna,sensor-type = <1>;
syna,delta-x-threshold = <5>;
syna,delta-y-threshold = <10>;
};
rmi4-f12@12 {
@ -626,7 +629,7 @@
pinctrl-0 = <&pinctrl_ucs1002_pins>;
reg = <0x32>;
interrupts-extended = <&gpio5 2 IRQ_TYPE_EDGE_BOTH>,
<&gpio3 21 IRQ_TYPE_EDGE_BOTH>;
<&gpio3 21 IRQ_TYPE_EDGE_FALLING>;
interrupt-names = "a_det", "alert";
};
@ -637,6 +640,7 @@
reg = <0x60>;
power-gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
Vdd-supply = <&reg_5p0v_main>;
sound-name-prefix = "HPA1";
};
};
@ -885,10 +889,6 @@
};
};
&wdog1 {
status = "disabled";
};
&iomuxc {
pinctrl_accel: accelgrp {
fsl,pins = <
@ -988,22 +988,22 @@
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b811
MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b811
>;
};
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b811
MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b811
>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b811
MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b811
>;
};

25
arch/arm/boot/dts/imx6qdl.dtsi
Просмотреть файл

@ -182,8 +182,6 @@
};
hdmi: hdmi@120000 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0x00120000 0x9000>;
interrupts = <0 115 0x04>;
gpr = <&gpr>;
@ -192,19 +190,24 @@
clock-names = "iahb", "isfr";
status = "disabled";
port@0 {
reg = <0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
hdmi_mux_0: endpoint {
remote-endpoint = <&ipu1_di0_hdmi>;
port@0 {
reg = <0>;
hdmi_mux_0: endpoint {
remote-endpoint = <&ipu1_di0_hdmi>;
};
};
};
port@1 {
reg = <1>;
port@1 {
reg = <1>;
hdmi_mux_1: endpoint {
remote-endpoint = <&ipu1_di1_hdmi>;
hdmi_mux_1: endpoint {
remote-endpoint = <&ipu1_di1_hdmi>;
};
};
};
};

13
arch/arm/boot/dts/imx6qp-vicutp.dts Normal file
Просмотреть файл

@ -0,0 +1,13 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Copyright (c) 2014 Protonic Holland
*/
/dts-v1/;
#include "imx6qp.dtsi"
#include "imx6qdl-vicut1.dtsi"
/ {
model = "Kverneland UT1P Board";
compatible = "kvg,vicutp", "fsl,imx6qp";
};

18
arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts
Просмотреть файл

@ -340,7 +340,6 @@
MX6SL_PAD_KEY_ROW7__GPIO4_IO07 0x79
MX6SL_PAD_ECSPI2_MOSI__GPIO4_IO13 0x79
MX6SL_PAD_KEY_COL5__GPIO4_IO02 0x79
MX6SL_PAD_KEY_ROW6__GPIO4_IO05 0x79
>;
};
@ -396,7 +395,14 @@
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
MX6SL_PAD_UART1_RXD__UART1_TX_DATA 0x1b0b1
MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
>;
};
pinctrl_uart4: uart4grp {
fsl,pins = <
MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1
MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1
>;
};
@ -543,11 +549,19 @@
};
&uart1 {
/* J4, through-holes */
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart4 {
/* TP198, next to J4, SMD pads */
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
status = "okay";
};
&usdhc2 {
pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
pinctrl-0 = <&pinctrl_usdhc2>;

15
arch/arm/boot/dts/imx6sl-tolino-shine3.dts
Просмотреть файл

@ -94,7 +94,6 @@
MX6SL_PAD_KEY_ROW7__GPIO4_IO07 0x79
MX6SL_PAD_ECSPI2_MOSI__GPIO4_IO13 0x79
MX6SL_PAD_KEY_COL5__GPIO4_IO02 0x79
MX6SL_PAD_KEY_ROW6__GPIO4_IO05 0x79
>;
};
@ -156,7 +155,14 @@
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
MX6SL_PAD_UART1_RXD__UART1_TX_DATA 0x1b0b1
MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
>;
};
pinctrl_uart4: uart4grp {
fsl,pins = <
MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1
MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1
>;
};
@ -300,6 +306,11 @@
pinctrl-0 = <&pinctrl_uart1>;
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
};
&usdhc2 {
pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
pinctrl-0 = <&pinctrl_usdhc2>;

13
arch/arm/boot/dts/imx6sll-kobo-clarahd.dts
Просмотреть файл

@ -104,7 +104,6 @@
MX6SLL_PAD_KEY_ROW7__GPIO4_IO07 0x79
MX6SLL_PAD_ECSPI2_MOSI__GPIO4_IO13 0x79
MX6SLL_PAD_KEY_COL5__GPIO4_IO02 0x79
MX6SLL_PAD_KEY_ROW6__GPIO4_IO05 0x79
>;
};
@ -170,6 +169,13 @@
>;
};
pinctrl_uart4: uart4grp {
fsl,pins = <
MX6SLL_PAD_KEY_ROW6__UART4_DCE_TX 0x1b0b1
MX6SLL_PAD_KEY_COL6__UART4_DCE_RX 0x1b0b1
>;
};
pinctrl_usbotg1: usbotg1grp {
fsl,pins = <
MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID 0x17059
@ -302,6 +308,11 @@
pinctrl-0 = <&pinctrl_uart1>;
};
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
};
&usdhc2 {
pinctrl-names = "default", "state_100mhz", "state_200mhz","sleep";
pinctrl-0 = <&pinctrl_usdhc2>;

2
arch/arm/boot/dts/imx6sx-sdb.dtsi
Просмотреть файл

@ -206,6 +206,7 @@
phy-mode = "rgmii-id";
phy-handle = <&ethphy1>;
phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
fsl,magic-packet;
status = "okay";
mdio {
@ -227,6 +228,7 @@
pinctrl-0 = <&pinctrl_enet2>;
phy-mode = "rgmii-id";
phy-handle = <&ethphy2>;
fsl,magic-packet;
status = "okay";
};

54
arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
Просмотреть файл

@ -101,7 +101,7 @@
status = "okay";
gpio-sck = <&gpio5 11 0>;
gpio-mosi = <&gpio5 10 0>;
cs-gpios = <&gpio5 7 0>;
cs-gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
num-chipselects = <1>;
#address-cells = <1>;
#size-cells = <0>;
@ -113,6 +113,7 @@
reg = <0>;
registers-number = <1>;
spi-max-frequency = <100000>;
enable-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
};
};
@ -145,6 +146,41 @@
reg = <0x1a>;
wlf,shared-lrclk;
};
camera@3c {
compatible = "ovti,ov5640";
reg = <0x3c>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_camera_clock>;
clocks = <&clks IMX6UL_CLK_CSI>;
clock-names = "xclk";
powerdown-gpios = <&gpio_spi 6 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpio_spi 5 GPIO_ACTIVE_LOW>;
port {
ov5640_to_parallel: endpoint {
remote-endpoint = <&parallel_from_ov5640>;
bus-width = <8>;
data-shift = <2>; /* lines 9:2 are used */
hsync-active = <0>;
vsync-active = <0>;
pclk-sample = <1>;
};
};
};
};
&csi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_csi1>;
status = "okay";
port {
parallel_from_ov5640: endpoint {
remote-endpoint = <&ov5640_to_parallel>;
bus-type = <5>; /* Parallel bus */
};
};
};
&fec1 {
@ -169,17 +205,26 @@
#size-cells = <0>;
ethphy0: ethernet-phy@2 {
compatible = "ethernet-phy-id0022.1560";
reg = <2>;
micrel,led-mode = <1>;
clocks = <&clks IMX6UL_CLK_ENET_REF>;
clock-names = "rmii-ref";
reset-gpios = <&gpio_spi 1 GPIO_ACTIVE_LOW>;
reset-assert-us = <10000>;
reset-deassert-us = <100>;
};
ethphy1: ethernet-phy@1 {
compatible = "ethernet-phy-id0022.1560";
reg = <1>;
micrel,led-mode = <1>;
clocks = <&clks IMX6UL_CLK_ENET2_REF>;
clock-names = "rmii-ref";
reset-gpios = <&gpio_spi 2 GPIO_ACTIVE_LOW>;
reset-assert-us = <10000>;
reset-deassert-us = <100>;
};
};
};
@ -343,9 +388,14 @@
&iomuxc {
pinctrl-names = "default";
pinctrl_csi1: csi1grp {
pinctrl_camera_clock: cameraclockgrp {
fsl,pins = <
MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088
>;
};
pinctrl_csi1: csi1grp {
fsl,pins = <
MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088
MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088
MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088

356
arch/arm/boot/dts/imx6ul-prti6g.dts Normal file
Просмотреть файл

@ -0,0 +1,356 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Copyright (c) 2016 Protonic Holland
* Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
*/
/dts-v1/;
#include "imx6ul.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
model = "Protonic PRTI6G Board";
compatible = "prt,prti6g", "fsl,imx6ul";
chosen {
stdout-path = &uart1;
};
clock_ksz8081_in: clock-ksz8081-in {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>;
};
clock_ksz8081_out: clock-ksz8081-out {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <50000000>;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_leds>;
led-0 {
label = "debug0";
gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
reg_3v2: regulator-3v2 {
compatible = "regulator-fixed";
regulator-name = "3v2";
regulator-min-microvolt = <3200000>;
regulator-max-microvolt = <3200000>;
};
};
&can1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1>;
status = "okay";
};
&can2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can2>;
status = "okay";
};
&ecspi1 {
cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi1>;
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <20000000>;
};
};
&ecspi2 {
cs-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
spi@0 {
compatible = "spidev";
reg = <0>;
spi-max-frequency = <1000000>;
};
};
&fec1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_eth1>;
phy-mode = "rmii";
phy-handle = <&rmii_phy>;
clocks = <&clks IMX6UL_CLK_ENET>,
<&clks IMX6UL_CLK_ENET_AHB>,
<&clks IMX6UL_CLK_ENET_PTP>,
<&clock_ksz8081_out>;
clock-names = "ipg", "ahb", "ptp",
"enet_clk_ref";
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
/* Microchip KSZ8081RNA PHY */
rmii_phy: ethernet-phy@0 {
reg = <0>;
interrupts-extended = <&gpio5 1 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
reset-assert-us = <10000>;
reset-deassert-us = <300>;
clocks = <&clock_ksz8081_in>;
clock-names = "rmii-ref";
};
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
clock-frequency = <100000>;
status = "okay";
/* additional i2c devices are added automatically by the boot loader */
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
clock-frequency = <100000>;
status = "okay";
adc@49 {
compatible = "ti,ads1015";
reg = <0x49>;
#address-cells = <1>;
#size-cells = <0>;
channel@4 {
reg = <4>;
ti,gain = <3>;
ti,datarate = <3>;
};
channel@5 {
reg = <5>;
ti,gain = <3>;
ti,datarate = <3>;
};
channel@6 {
reg = <6>;
ti,gain = <3>;
ti,datarate = <3>;
};
channel@7 {
reg = <7>;
ti,gain = <3>;
ti,datarate = <3>;
};
};
rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
};
temperature-sensor@70 {
compatible = "ti,tmp103";
reg = <0x70>;
};
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&usbotg1 {
dr_mode = "host";
status = "okay";
};
&usdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc1>;
cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
vmmc-supply = <&reg_3v2>;
no-1-8-v;
disable-wp;
cap-sd-highspeed;
no-mmc;
no-sdio;
status = "okay";
};
&usdhc2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc2>;
bus-width = <8>;
no-1-8-v;
non-removable;
no-sd;
no-sdio;
status = "okay";
};
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
pinctrl_can1: can1grp {
fsl,pins = <
MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x0b0b0
MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x0b0b0
/* SR */
MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x0b0b0
/* TERM */
MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0
/* nSMBALERT */
MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x0b0b0
>;
};
pinctrl_can2: can2grp {
fsl,pins = <
MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x0b0b0
MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x0b0b0
/* SR */
MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x0b0b0
>;
};
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x0b0b0
MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x000b1
MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x0b0b0
MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x0b0b0
>;
};
pinctrl_ecspi2: ecspi2grp {
fsl,pins = <
MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x0b0b0
MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x000b1
MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x0b0b0
MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x0b0b0
>;
};
pinctrl_eth1: eth1grp {
fsl,pins = <
MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x100b0
MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x100b0
MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x1b000
/* PHY ENET1_RST */
MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x00880
/* PHY ENET1_IRQ */
MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x00880
>;
};
pinctrl_hog: hoggrp {
fsl,pins = <
/* HW revision detect */
/* REV_ID0 */
MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08 0x1b0b0
/* REV_ID1 */
MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09 0x1b0b0
/* REV_ID2 */
MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10 0x1b0b0
/* REV_ID3 */
MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11 0x1b0b0
/* BOARD_ID0 */
MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x1b0b0
/* BOARD_ID1 */
MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14 0x1b0b0
/* BOARD_ID2 */
MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x1b0b0
/* BOARD_ID3 */
MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12 0x1b0b0
/* Safety controller IO */
/* WAKE_SC */
MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x1b0b0
/* PROGRAM_SC */
MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x1b0b0
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0
MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0
>;
};
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX6UL_PAD_CSI_VSYNC__I2C2_SDA 0x4001b8b0
MX6UL_PAD_CSI_HSYNC__I2C2_SCL 0x4001b8b0
>;
};
pinctrl_leds: ledsgrp {
fsl,pins = <
MX6UL_PAD_NAND_DQS__GPIO4_IO16 0x1b0b0
>;
};
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
>;
};
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x070b1
MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x07099
MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x070b1
MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x070b1
MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x070b1
MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x070b1
/* SD1 CD */
MX6UL_PAD_NAND_READY_B__GPIO4_IO12 0x170b0
>;
};
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9
MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9
MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9
MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9
MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0
>;
};
};

2
arch/arm/boot/dts/imx6ul.dtsi
Просмотреть файл

@ -538,6 +538,7 @@
fsl,num-tx-queues = <1>;
fsl,num-rx-queues = <1>;
fsl,stop-mode = <&gpr 0x10 4>;
fsl,magic-packet;
status = "disabled";
};
@ -885,6 +886,7 @@
fsl,num-tx-queues = <1>;
fsl,num-rx-queues = <1>;
fsl,stop-mode = <&gpr 0x10 3>;
fsl,magic-packet;
status = "disabled";
};

1
arch/arm/boot/dts/imx7d-flex-concentrator.dts
Просмотреть файл

@ -115,6 +115,7 @@
compatible = "nxp,pcf2127";
reg = <0>;
spi-max-frequency = <2000000>;
reset-source;
};
};

1
arch/arm/boot/dts/imx7s.dtsi
Просмотреть файл

@ -151,6 +151,7 @@
timer {
compatible = "arm,armv7-timer";
arm,cpu-registers-not-fw-configured;
interrupt-parent = <&intc>;
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,

1
arch/arm/mach-imx/suspend-imx6.S
Просмотреть файл

@ -67,6 +67,7 @@
#define MX6Q_CCM_CCR 0x0
.align 3
.arm
.macro sync_l2_cache

2
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
Просмотреть файл

@ -101,7 +101,7 @@
reboot {
compatible ="syscon-reboot";
regmap = <&rst>;
offset = <0xb0>;
offset = <0>;
mask = <0x02>;
};

2
arch/arm64/boot/dts/freescale/imx8mn.dtsi
Просмотреть файл

@ -253,7 +253,7 @@
#size-cells = <1>;
ranges;
spba: bus@30000000 {
spba: spba-bus@30000000 {
compatible = "fsl,spba-bus", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;

2
arch/arm64/boot/dts/freescale/imx8mp.dtsi
Просмотреть файл

@ -266,7 +266,7 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-ranges = <&iomuxc 0 56 26>, <&iomuxc 0 144 4>;
gpio-ranges = <&iomuxc 0 56 26>, <&iomuxc 26 144 4>;
};
gpio4: gpio@30230000 {

1
drivers/firmware/imx/Kconfig
Просмотреть файл

@ -13,6 +13,7 @@ config IMX_DSP
config IMX_SCU
bool "IMX SCU Protocol driver"
depends on IMX_MBOX
select SOC_BUS
help
The System Controller Firmware (SCFW) is a low-level system function
which runs on a dedicated Cortex-M core to provide power, clock, and

2
drivers/soc/imx/Kconfig
Просмотреть файл

@ -13,7 +13,7 @@ config SOC_IMX8M
depends on ARCH_MXC || COMPILE_TEST
default ARCH_MXC && ARM64
select SOC_BUS
select ARM_GIC_V3 if ARCH_MXC
select ARM_GIC_V3 if ARCH_MXC && ARCH_MULTI_V7
help
If you say yes here you get support for the NXP i.MX8M family
support, it will provide the SoC info like SoC family,