spi: qup: Remove chip select function

This patch removes the chip select function.  Chip select should instead be
supported using GPIOs, defining the DT entry "cs-gpios", and letting the SPI
core assert/deassert the chip select as it sees fit.

The chip select control inside the controller is buggy.  It is supposed to
automatically assert the chip select based on the activity in the controller,
but it is buggy and doesn't work at all.  So instead we elect to use GPIOs.

Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This commit is contained in:
Andy Gross 2014-06-12 14:34:10 -05:00 коммит произвёл Mark Brown
Родитель 045c243a51
Коммит 4a8573abe9
2 изменённых файлов: 12 добавлений и 27 удалений

Просмотреть файл

@ -23,6 +23,12 @@ Optional properties:
- spi-max-frequency: Specifies maximum SPI clock frequency,
Units - Hz. Definition as per
Documentation/devicetree/bindings/spi/spi-bus.txt
- num-cs: total number of chipselects
- cs-gpios: should specify GPIOs used for chipselects.
The gpios will be referred to as reg = <index> in the SPI child
nodes. If unspecified, a single SPI device without a chip
select can be used.
SPI slave nodes must be children of the SPI master node and can contain
properties described in Documentation/devicetree/bindings/spi/spi-bus.txt

Просмотреть файл

@ -424,31 +424,6 @@ static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
return 0;
}
static void spi_qup_set_cs(struct spi_device *spi, bool enable)
{
struct spi_qup *controller = spi_master_get_devdata(spi->master);
u32 iocontol, mask;
iocontol = readl_relaxed(controller->base + SPI_IO_CONTROL);
/* Disable auto CS toggle and use manual */
iocontol &= ~SPI_IO_C_MX_CS_MODE;
iocontol |= SPI_IO_C_FORCE_CS;
iocontol &= ~SPI_IO_C_CS_SELECT_MASK;
iocontol |= SPI_IO_C_CS_SELECT(spi->chip_select);
mask = SPI_IO_C_CS_N_POLARITY_0 << spi->chip_select;
if (enable)
iocontol |= mask;
else
iocontol &= ~mask;
writel_relaxed(iocontol, controller->base + SPI_IO_CONTROL);
}
static int spi_qup_transfer_one(struct spi_master *master,
struct spi_device *spi,
struct spi_transfer *xfer)
@ -571,12 +546,16 @@ static int spi_qup_probe(struct platform_device *pdev)
return -ENOMEM;
}
/* use num-cs unless not present or out of range */
if (of_property_read_u16(dev->of_node, "num-cs",
&master->num_chipselect) ||
(master->num_chipselect > SPI_NUM_CHIPSELECTS))
master->num_chipselect = SPI_NUM_CHIPSELECTS;
master->bus_num = pdev->id;
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP;
master->num_chipselect = SPI_NUM_CHIPSELECTS;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
master->max_speed_hz = max_freq;
master->set_cs = spi_qup_set_cs;
master->transfer_one = spi_qup_transfer_one;
master->dev.of_node = pdev->dev.of_node;
master->auto_runtime_pm = true;