leds: LED driver for National Semiconductor LP3944 Funlight Chip
LEDs driver for National Semiconductor LP3944 Funlight Chip http://www.national.com/pf/LP/LP3944.html This helper chip can drive up to 8 leds, with two programmable DIM modes; it could even be used as a gpio expander but this driver assumes it is used as a led controller. The DIM modes are used to set _blink_ patterns for leds, the pattern is specified supplying two parameters: - period: from 0s to 1.6s - duty cycle: percentage of the period the led is on, from 0 to 100 LP3944 can be found on Motorola A910 smartphone, where it drives the rgb leds, the camera flash light and the displays backlights. Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
This commit is contained in:
Antonio Ospite
Richard Purdie
Родитель
07172d2bfa
Коммит
5054d39e32
|
|
@ -0,0 +1,50 @@
|
|||
Kernel driver lp3944
|
||||
====================
|
||||
|
||||
* National Semiconductor LP3944 Fun-light Chip
|
||||
Prefix: 'lp3944'
|
||||
Addresses scanned: None (see the Notes section below)
|
||||
Datasheet: Publicly available at the National Semiconductor website
|
||||
http://www.national.com/pf/LP/LP3944.html
|
||||
|
||||
Authors:
|
||||
Antonio Ospite <ospite@studenti.unina.it>
|
||||
|
||||
|
||||
Description
|
||||
-----------
|
||||
The LP3944 is a helper chip that can drive up to 8 leds, with two programmable
|
||||
DIM modes; it could even be used as a gpio expander but this driver assumes it
|
||||
is used as a led controller.
|
||||
|
||||
The DIM modes are used to set _blink_ patterns for leds, the pattern is
|
||||
specified supplying two parameters:
|
||||
- period: from 0s to 1.6s
|
||||
- duty cycle: percentage of the period the led is on, from 0 to 100
|
||||
|
||||
Setting a led in DIM0 or DIM1 mode makes it blink according to the pattern.
|
||||
See the datasheet for details.
|
||||
|
||||
LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
|
||||
leds, the camera flash light and the lcds power.
|
||||
|
||||
|
||||
Notes
|
||||
-----
|
||||
The chip is used mainly in embedded contexts, so this driver expects it is
|
||||
registered using the i2c_board_info mechanism.
|
||||
|
||||
To register the chip at address 0x60 on adapter 0, set the platform data
|
||||
according to include/linux/leds-lp3944.h, set the i2c board info:
|
||||
|
||||
static struct i2c_board_info __initdata a910_i2c_board_info[] = {
|
||||
{
|
||||
I2C_BOARD_INFO("lp3944", 0x60),
|
||||
.platform_data = &a910_lp3944_leds,
|
||||
},
|
||||
};
|
||||
|
||||
and register it in the platform init function
|
||||
|
||||
i2c_register_board_info(0, a910_i2c_board_info,
|
||||
ARRAY_SIZE(a910_i2c_board_info));
|
||||
|
|
@ -146,6 +146,17 @@ config LEDS_GPIO_OF
|
|||
of_platform devices. For instance, LEDs which are listed in a "dts"
|
||||
file.
|
||||
|
||||
config LEDS_LP3944
|
||||
tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
|
||||
depends on LEDS_CLASS && I2C
|
||||
help
|
||||
This option enables support for LEDs connected to the National
|
||||
Semiconductor LP3944 Lighting Management Unit (LMU) also known as
|
||||
Fun Light Chip.
|
||||
|
||||
To compile this driver as a module, choose M here: the
|
||||
module will be called leds-lp3944.
|
||||
|
||||
config LEDS_CLEVO_MAIL
|
||||
tristate "Mail LED on Clevo notebook"
|
||||
depends on LEDS_CLASS && X86 && SERIO_I8042 && DMI
|
||||
|
|
|
|||
|
|
@ -20,6 +20,7 @@ obj-$(CONFIG_LEDS_COBALT_RAQ) += leds-cobalt-raq.o
|
|||
obj-$(CONFIG_LEDS_SUNFIRE) += leds-sunfire.o
|
||||
obj-$(CONFIG_LEDS_PCA9532) += leds-pca9532.o
|
||||
obj-$(CONFIG_LEDS_GPIO) += leds-gpio.o
|
||||
obj-$(CONFIG_LEDS_LP3944) += leds-lp3944.o
|
||||
obj-$(CONFIG_LEDS_CLEVO_MAIL) += leds-clevo-mail.o
|
||||
obj-$(CONFIG_LEDS_HP6XX) += leds-hp6xx.o
|
||||
obj-$(CONFIG_LEDS_FSG) += leds-fsg.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,466 @@
|
|||
/*
|
||||
* leds-lp3944.c - driver for National Semiconductor LP3944 Funlight Chip
|
||||
*
|
||||
* Copyright (C) 2009 Antonio Ospite <ospite@studenti.unina.it>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*
|
||||
*/
|
||||
|
||||
/*
|
||||
* I2C driver for National Semiconductor LP3944 Funlight Chip
|
||||
* http://www.national.com/pf/LP/LP3944.html
|
||||
*
|
||||
* This helper chip can drive up to 8 leds, with two programmable DIM modes;
|
||||
* it could even be used as a gpio expander but this driver assumes it is used
|
||||
* as a led controller.
|
||||
*
|
||||
* The DIM modes are used to set _blink_ patterns for leds, the pattern is
|
||||
* specified supplying two parameters:
|
||||
* - period: from 0s to 1.6s
|
||||
* - duty cycle: percentage of the period the led is on, from 0 to 100
|
||||
*
|
||||
* LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
|
||||
* leds, the camera flash light and the displays backlights.
|
||||
*/
|
||||
|
||||
#include <linux/module.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/leds.h>
|
||||
#include <linux/mutex.h>
|
||||
#include <linux/workqueue.h>
|
||||
#include <linux/leds-lp3944.h>
|
||||
|
||||
/* Read Only Registers */
|
||||
#define LP3944_REG_INPUT1 0x00 /* LEDs 0-7 InputRegister (Read Only) */
|
||||
#define LP3944_REG_REGISTER1 0x01 /* None (Read Only) */
|
||||
|
||||
#define LP3944_REG_PSC0 0x02 /* Frequency Prescaler 0 (R/W) */
|
||||
#define LP3944_REG_PWM0 0x03 /* PWM Register 0 (R/W) */
|
||||
#define LP3944_REG_PSC1 0x04 /* Frequency Prescaler 1 (R/W) */
|
||||
#define LP3944_REG_PWM1 0x05 /* PWM Register 1 (R/W) */
|
||||
#define LP3944_REG_LS0 0x06 /* LEDs 0-3 Selector (R/W) */
|
||||
#define LP3944_REG_LS1 0x07 /* LEDs 4-7 Selector (R/W) */
|
||||
|
||||
/* These registers are not used to control leds in LP3944, they can store
|
||||
* arbitrary values which the chip will ignore.
|
||||
*/
|
||||
#define LP3944_REG_REGISTER8 0x08
|
||||
#define LP3944_REG_REGISTER9 0x09
|
||||
|
||||
#define LP3944_DIM0 0
|
||||
#define LP3944_DIM1 1
|
||||
|
||||
/* period in ms */
|
||||
#define LP3944_PERIOD_MIN 0
|
||||
#define LP3944_PERIOD_MAX 1600
|
||||
|
||||
/* duty cycle is a percentage */
|
||||
#define LP3944_DUTY_CYCLE_MIN 0
|
||||
#define LP3944_DUTY_CYCLE_MAX 100
|
||||
|
||||
#define ldev_to_led(c) container_of(c, struct lp3944_led_data, ldev)
|
||||
|
||||
/* Saved data */
|
||||
struct lp3944_led_data {
|
||||
u8 id;
|
||||
enum lp3944_type type;
|
||||
enum lp3944_status status;
|
||||
struct led_classdev ldev;
|
||||
struct i2c_client *client;
|
||||
struct work_struct work;
|
||||
};
|
||||
|
||||
struct lp3944_data {
|
||||
struct mutex lock;
|
||||
struct i2c_client *client;
|
||||
struct lp3944_led_data leds[LP3944_LEDS_MAX];
|
||||
};
|
||||
|
||||
static int lp3944_reg_read(struct i2c_client *client, u8 reg, u8 *value)
|
||||
{
|
||||
int tmp;
|
||||
|
||||
tmp = i2c_smbus_read_byte_data(client, reg);
|
||||
if (tmp < 0)
|
||||
return -EINVAL;
|
||||
|
||||
*value = tmp;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int lp3944_reg_write(struct i2c_client *client, u8 reg, u8 value)
|
||||
{
|
||||
return i2c_smbus_write_byte_data(client, reg, value);
|
||||
}
|
||||
|
||||
/**
|
||||
* Set the period for DIM status
|
||||
*
|
||||
* @client: the i2c client
|
||||
* @dim: either LP3944_DIM0 or LP3944_DIM1
|
||||
* @period: period of a blink, that is a on/off cycle, expressed in ms.
|
||||
*/
|
||||
static int lp3944_dim_set_period(struct i2c_client *client, u8 dim, u16 period)
|
||||
{
|
||||
u8 psc_reg;
|
||||
u8 psc_value;
|
||||
int err;
|
||||
|
||||
if (dim == LP3944_DIM0)
|
||||
psc_reg = LP3944_REG_PSC0;
|
||||
else if (dim == LP3944_DIM1)
|
||||
psc_reg = LP3944_REG_PSC1;
|
||||
else
|
||||
return -EINVAL;
|
||||
|
||||
/* Convert period to Prescaler value */
|
||||
if (period > LP3944_PERIOD_MAX)
|
||||
return -EINVAL;
|
||||
|
||||
psc_value = (period * 255) / LP3944_PERIOD_MAX;
|
||||
|
||||
err = lp3944_reg_write(client, psc_reg, psc_value);
|
||||
|
||||
return err;
|
||||
}
|
||||
|
||||
/**
|
||||
* Set the duty cycle for DIM status
|
||||
*
|
||||
* @client: the i2c client
|
||||
* @dim: either LP3944_DIM0 or LP3944_DIM1
|
||||
* @duty_cycle: percentage of a period during which a led is ON
|
||||
*/
|
||||
static int lp3944_dim_set_dutycycle(struct i2c_client *client, u8 dim,
|
||||
u8 duty_cycle)
|
||||
{
|
||||
u8 pwm_reg;
|
||||
u8 pwm_value;
|
||||
int err;
|
||||
|
||||
if (dim == LP3944_DIM0)
|
||||
pwm_reg = LP3944_REG_PWM0;
|
||||
else if (dim == LP3944_DIM1)
|
||||
pwm_reg = LP3944_REG_PWM1;
|
||||
else
|
||||
return -EINVAL;
|
||||
|
||||
/* Convert duty cycle to PWM value */
|
||||
if (duty_cycle > LP3944_DUTY_CYCLE_MAX)
|
||||
return -EINVAL;
|
||||
|
||||
pwm_value = (duty_cycle * 255) / LP3944_DUTY_CYCLE_MAX;
|
||||
|
||||
err = lp3944_reg_write(client, pwm_reg, pwm_value);
|
||||
|
||||
return err;
|
||||
}
|
||||
|
||||
/**
|
||||
* Set the led status
|
||||
*
|
||||
* @led: a lp3944_led_data structure
|
||||
* @status: one of LP3944_LED_STATUS_OFF
|
||||
* LP3944_LED_STATUS_ON
|
||||
* LP3944_LED_STATUS_DIM0
|
||||
* LP3944_LED_STATUS_DIM1
|
||||
*/
|
||||
static int lp3944_led_set(struct lp3944_led_data *led, u8 status)
|
||||
{
|
||||
struct lp3944_data *data = i2c_get_clientdata(led->client);
|
||||
u8 id = led->id;
|
||||
u8 reg;
|
||||
u8 val = 0;
|
||||
int err;
|
||||
|
||||
dev_dbg(&led->client->dev, "%s: %s, status before normalization:%d\n",
|
||||
__func__, led->ldev.name, status);
|
||||
|
||||
switch (id) {
|
||||
case LP3944_LED0:
|
||||
case LP3944_LED1:
|
||||
case LP3944_LED2:
|
||||
case LP3944_LED3:
|
||||
reg = LP3944_REG_LS0;
|
||||
break;
|
||||
case LP3944_LED4:
|
||||
case LP3944_LED5:
|
||||
case LP3944_LED6:
|
||||
case LP3944_LED7:
|
||||
id -= LP3944_LED4;
|
||||
reg = LP3944_REG_LS1;
|
||||
break;
|
||||
default:
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
if (status > LP3944_LED_STATUS_DIM1)
|
||||
return -EINVAL;
|
||||
|
||||
/* invert only 0 and 1, leave unchanged the other values,
|
||||
* remember we are abusing status to set blink patterns
|
||||
*/
|
||||
if (led->type == LP3944_LED_TYPE_LED_INVERTED && status < 2)
|
||||
status = 1 - status;
|
||||
|
||||
mutex_lock(&data->lock);
|
||||
lp3944_reg_read(led->client, reg, &val);
|
||||
|
||||
val &= ~(LP3944_LED_STATUS_MASK << (id << 1));
|
||||
val |= (status << (id << 1));
|
||||
|
||||
dev_dbg(&led->client->dev, "%s: %s, reg:%d id:%d status:%d val:%#x\n",
|
||||
__func__, led->ldev.name, reg, id, status, val);
|
||||
|
||||
/* set led status */
|
||||
err = lp3944_reg_write(led->client, reg, val);
|
||||
mutex_unlock(&data->lock);
|
||||
|
||||
return err;
|
||||
}
|
||||
|
||||
static int lp3944_led_set_blink(struct led_classdev *led_cdev,
|
||||
unsigned long *delay_on,
|
||||
unsigned long *delay_off)
|
||||
{
|
||||
struct lp3944_led_data *led = ldev_to_led(led_cdev);
|
||||
u16 period;
|
||||
u8 duty_cycle;
|
||||
int err;
|
||||
|
||||
/* units are in ms */
|
||||
if (*delay_on + *delay_off > LP3944_PERIOD_MAX)
|
||||
return -EINVAL;
|
||||
|
||||
if (*delay_on == 0 && *delay_off == 0) {
|
||||
/* Special case: the leds subsystem requires a default user
|
||||
* friendly blink pattern for the LED. Let's blink the led
|
||||
* slowly (1Hz).
|
||||
*/
|
||||
*delay_on = 500;
|
||||
*delay_off = 500;
|
||||
}
|
||||
|
||||
period = (*delay_on) + (*delay_off);
|
||||
|
||||
/* duty_cycle is the percentage of period during which the led is ON */
|
||||
duty_cycle = 100 * (*delay_on) / period;
|
||||
|
||||
/* invert duty cycle for inverted leds, this has the same effect of
|
||||
* swapping delay_on and delay_off
|
||||
*/
|
||||
if (led->type == LP3944_LED_TYPE_LED_INVERTED)
|
||||
duty_cycle = 100 - duty_cycle;
|
||||
|
||||
/* NOTE: using always the first DIM mode, this means that all leds
|
||||
* will have the same blinking pattern.
|
||||
*
|
||||
* We could find a way later to have two leds blinking in hardware
|
||||
* with different patterns at the same time, falling back to software
|
||||
* control for the other ones.
|
||||
*/
|
||||
err = lp3944_dim_set_period(led->client, LP3944_DIM0, period);
|
||||
if (err)
|
||||
return err;
|
||||
|
||||
err = lp3944_dim_set_dutycycle(led->client, LP3944_DIM0, duty_cycle);
|
||||
if (err)
|
||||
return err;
|
||||
|
||||
dev_dbg(&led->client->dev, "%s: OK hardware accelerated blink!\n",
|
||||
__func__);
|
||||
|
||||
led->status = LP3944_LED_STATUS_DIM0;
|
||||
schedule_work(&led->work);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void lp3944_led_set_brightness(struct led_classdev *led_cdev,
|
||||
enum led_brightness brightness)
|
||||
{
|
||||
struct lp3944_led_data *led = ldev_to_led(led_cdev);
|
||||
|
||||
dev_dbg(&led->client->dev, "%s: %s, %d\n",
|
||||
__func__, led_cdev->name, brightness);
|
||||
|
||||
led->status = brightness;
|
||||
schedule_work(&led->work);
|
||||
}
|
||||
|
||||
static void lp3944_led_work(struct work_struct *work)
|
||||
{
|
||||
struct lp3944_led_data *led;
|
||||
|
||||
led = container_of(work, struct lp3944_led_data, work);
|
||||
lp3944_led_set(led, led->status);
|
||||
}
|
||||
|
||||
static int lp3944_configure(struct i2c_client *client,
|
||||
struct lp3944_data *data,
|
||||
struct lp3944_platform_data *pdata)
|
||||
{
|
||||
int i, err = 0;
|
||||
|
||||
for (i = 0; i < pdata->leds_size; i++) {
|
||||
struct lp3944_led *pled = &pdata->leds[i];
|
||||
struct lp3944_led_data *led = &data->leds[i];
|
||||
led->client = client;
|
||||
led->id = i;
|
||||
|
||||
switch (pled->type) {
|
||||
|
||||
case LP3944_LED_TYPE_LED:
|
||||
case LP3944_LED_TYPE_LED_INVERTED:
|
||||
led->type = pled->type;
|
||||
led->status = pled->status;
|
||||
led->ldev.name = pled->name;
|
||||
led->ldev.max_brightness = 1;
|
||||
led->ldev.brightness_set = lp3944_led_set_brightness;
|
||||
led->ldev.blink_set = lp3944_led_set_blink;
|
||||
led->ldev.flags = LED_CORE_SUSPENDRESUME;
|
||||
|
||||
INIT_WORK(&led->work, lp3944_led_work);
|
||||
err = led_classdev_register(&client->dev, &led->ldev);
|
||||
if (err < 0) {
|
||||
dev_err(&client->dev,
|
||||
"couldn't register LED %s\n",
|
||||
led->ldev.name);
|
||||
goto exit;
|
||||
}
|
||||
|
||||
/* to expose the default value to userspace */
|
||||
led->ldev.brightness = led->status;
|
||||
|
||||
/* Set the default led status */
|
||||
err = lp3944_led_set(led, led->status);
|
||||
if (err < 0) {
|
||||
dev_err(&client->dev,
|
||||
"%s couldn't set STATUS %d\n",
|
||||
led->ldev.name, led->status);
|
||||
goto exit;
|
||||
}
|
||||
break;
|
||||
|
||||
case LP3944_LED_TYPE_NONE:
|
||||
default:
|
||||
break;
|
||||
|
||||
}
|
||||
}
|
||||
return 0;
|
||||
|
||||
exit:
|
||||
if (i > 0)
|
||||
for (i = i - 1; i >= 0; i--)
|
||||
switch (pdata->leds[i].type) {
|
||||
|
||||
case LP3944_LED_TYPE_LED:
|
||||
case LP3944_LED_TYPE_LED_INVERTED:
|
||||
led_classdev_unregister(&data->leds[i].ldev);
|
||||
cancel_work_sync(&data->leds[i].work);
|
||||
break;
|
||||
|
||||
case LP3944_LED_TYPE_NONE:
|
||||
default:
|
||||
break;
|
||||
}
|
||||
|
||||
return err;
|
||||
}
|
||||
|
||||
static int __devinit lp3944_probe(struct i2c_client *client,
|
||||
const struct i2c_device_id *id)
|
||||
{
|
||||
struct lp3944_platform_data *lp3944_pdata = client->dev.platform_data;
|
||||
struct lp3944_data *data;
|
||||
|
||||
if (lp3944_pdata == NULL) {
|
||||
dev_err(&client->dev, "no platform data\n");
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
/* Let's see whether this adapter can support what we need. */
|
||||
if (!i2c_check_functionality(client->adapter,
|
||||
I2C_FUNC_SMBUS_BYTE_DATA)) {
|
||||
dev_err(&client->dev, "insufficient functionality!\n");
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
data = kzalloc(sizeof(struct lp3944_data), GFP_KERNEL);
|
||||
if (!data)
|
||||
return -ENOMEM;
|
||||
|
||||
data->client = client;
|
||||
i2c_set_clientdata(client, data);
|
||||
|
||||
mutex_init(&data->lock);
|
||||
|
||||
dev_info(&client->dev, "lp3944 enabled\n");
|
||||
|
||||
lp3944_configure(client, data, lp3944_pdata);
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int __devexit lp3944_remove(struct i2c_client *client)
|
||||
{
|
||||
struct lp3944_platform_data *pdata = client->dev.platform_data;
|
||||
struct lp3944_data *data = i2c_get_clientdata(client);
|
||||
int i;
|
||||
|
||||
for (i = 0; i < pdata->leds_size; i++)
|
||||
switch (data->leds[i].type) {
|
||||
case LP3944_LED_TYPE_LED:
|
||||
case LP3944_LED_TYPE_LED_INVERTED:
|
||||
led_classdev_unregister(&data->leds[i].ldev);
|
||||
cancel_work_sync(&data->leds[i].work);
|
||||
break;
|
||||
|
||||
case LP3944_LED_TYPE_NONE:
|
||||
default:
|
||||
break;
|
||||
}
|
||||
|
||||
kfree(data);
|
||||
i2c_set_clientdata(client, NULL);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
/* lp3944 i2c driver struct */
|
||||
static const struct i2c_device_id lp3944_id[] = {
|
||||
{"lp3944", 0},
|
||||
{}
|
||||
};
|
||||
|
||||
MODULE_DEVICE_TABLE(i2c, lp3944_id);
|
||||
|
||||
static struct i2c_driver lp3944_driver = {
|
||||
.driver = {
|
||||
.name = "lp3944",
|
||||
},
|
||||
.probe = lp3944_probe,
|
||||
.remove = __devexit_p(lp3944_remove),
|
||||
.id_table = lp3944_id,
|
||||
};
|
||||
|
||||
static int __init lp3944_module_init(void)
|
||||
{
|
||||
return i2c_add_driver(&lp3944_driver);
|
||||
}
|
||||
|
||||
static void __exit lp3944_module_exit(void)
|
||||
{
|
||||
i2c_del_driver(&lp3944_driver);
|
||||
}
|
||||
|
||||
module_init(lp3944_module_init);
|
||||
module_exit(lp3944_module_exit);
|
||||
|
||||
MODULE_AUTHOR("Antonio Ospite <ospite@studenti.unina.it>");
|
||||
MODULE_DESCRIPTION("LP3944 Fun Light Chip");
|
||||
MODULE_LICENSE("GPL");
|
||||
|
|
@ -0,0 +1,53 @@
|
|||
/*
|
||||
* leds-lp3944.h - platform data structure for lp3944 led controller
|
||||
*
|
||||
* Copyright (C) 2009 Antonio Ospite <ospite@studenti.unina.it>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*
|
||||
*/
|
||||
|
||||
#ifndef __LINUX_LEDS_LP3944_H
|
||||
#define __LINUX_LEDS_LP3944_H
|
||||
|
||||
#include <linux/leds.h>
|
||||
#include <linux/workqueue.h>
|
||||
|
||||
#define LP3944_LED0 0
|
||||
#define LP3944_LED1 1
|
||||
#define LP3944_LED2 2
|
||||
#define LP3944_LED3 3
|
||||
#define LP3944_LED4 4
|
||||
#define LP3944_LED5 5
|
||||
#define LP3944_LED6 6
|
||||
#define LP3944_LED7 7
|
||||
#define LP3944_LEDS_MAX 8
|
||||
|
||||
#define LP3944_LED_STATUS_MASK 0x03
|
||||
enum lp3944_status {
|
||||
LP3944_LED_STATUS_OFF = 0x0,
|
||||
LP3944_LED_STATUS_ON = 0x1,
|
||||
LP3944_LED_STATUS_DIM0 = 0x2,
|
||||
LP3944_LED_STATUS_DIM1 = 0x3
|
||||
};
|
||||
|
||||
enum lp3944_type {
|
||||
LP3944_LED_TYPE_NONE,
|
||||
LP3944_LED_TYPE_LED,
|
||||
LP3944_LED_TYPE_LED_INVERTED,
|
||||
};
|
||||
|
||||
struct lp3944_led {
|
||||
char *name;
|
||||
enum lp3944_type type;
|
||||
enum lp3944_status status;
|
||||
};
|
||||
|
||||
struct lp3944_platform_data {
|
||||
struct lp3944_led leds[LP3944_LEDS_MAX];
|
||||
u8 leds_size;
|
||||
};
|
||||
|
||||
#endif /* __LINUX_LEDS_LP3944_H */
|
||||
Загрузка…
Ссылка в новой задаче