drm/pl111: Insert delay before powering up PL11x
The old codebase has a delay between enabling and powering up the PL11x. According to the manual for PL110, ARM DDI 0161E page 1-5 and the PL111 manual ARM DDI 0293C page 1-6, the power sequence should be such that once Vdd is stable (which we assume it is at boot) LCDEN is enabled first and then CLPOWER should be enabled "after the signals have stabilized" and this is said to be display-dependent. The old codebase uses 20ms. Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20170908124709.4758-5-linus.walleij@linaro.org
This commit is contained in:
Родитель
fa83306cd1
Коммит
52289a07a0
|
@ -155,8 +155,8 @@ static void pl111_display_enable(struct drm_simple_display_pipe *pipe,
|
|||
|
||||
writel(0, priv->regs + CLCD_TIM3);
|
||||
|
||||
/* Enable and Power Up */
|
||||
cntl = CNTL_LCDEN | CNTL_LCDTFT | CNTL_LCDPWR | CNTL_LCDVCOMP(1);
|
||||
/* Hard-code TFT panel */
|
||||
cntl = CNTL_LCDEN | CNTL_LCDTFT | CNTL_LCDVCOMP(1);
|
||||
|
||||
/* Note that the the hardware's format reader takes 'r' from
|
||||
* the low bit, while DRM formats list channels from high bit
|
||||
|
@ -199,6 +199,17 @@ static void pl111_display_enable(struct drm_simple_display_pipe *pipe,
|
|||
break;
|
||||
}
|
||||
|
||||
/* Power sequence: first enable and chill */
|
||||
writel(cntl, priv->regs + priv->ctrl);
|
||||
|
||||
/*
|
||||
* We expect this delay to stabilize the contrast
|
||||
* voltage Vee as stipulated by the manual
|
||||
*/
|
||||
msleep(20);
|
||||
|
||||
/* Power Up */
|
||||
cntl |= CNTL_LCDPWR;
|
||||
writel(cntl, priv->regs + priv->ctrl);
|
||||
|
||||
drm_crtc_vblank_on(crtc);
|
||||
|
@ -209,10 +220,24 @@ void pl111_display_disable(struct drm_simple_display_pipe *pipe)
|
|||
struct drm_crtc *crtc = &pipe->crtc;
|
||||
struct drm_device *drm = crtc->dev;
|
||||
struct pl111_drm_dev_private *priv = drm->dev_private;
|
||||
u32 cntl;
|
||||
|
||||
drm_crtc_vblank_off(crtc);
|
||||
|
||||
/* Disable and Power Down */
|
||||
/* Power Down */
|
||||
cntl = readl(priv->regs + priv->ctrl);
|
||||
if (cntl & CNTL_LCDPWR) {
|
||||
cntl &= ~CNTL_LCDPWR;
|
||||
writel(cntl, priv->regs + priv->ctrl);
|
||||
}
|
||||
|
||||
/*
|
||||
* We expect this delay to stabilize the contrast voltage Vee as
|
||||
* stipulated by the manual
|
||||
*/
|
||||
msleep(20);
|
||||
|
||||
/* Disable */
|
||||
writel(0, priv->regs + priv->ctrl);
|
||||
|
||||
clk_disable_unprepare(priv->clk);
|
||||
|
|
Загрузка…
Ссылка в новой задаче