ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7
MPP7 is currently muxed as "gpio", but this function doesn't exist for MPP7, only "gpo" is available. This causes the following error: kirkwood-pinctrl f1010000.pin-controller: unsupported function gpio on pin mpp7 pinctrl core: failed to register map default (6): invalid type given kirkwood-pinctrl f1010000.pin-controller: error claiming hogs: -22 kirkwood-pinctrl f1010000.pin-controller: could not claim hogs: -22 kirkwood-pinctrl f1010000.pin-controller: unable to register pinctrl driver kirkwood-pinctrl: probe of f1010000.pin-controller failed with error -22 So the pinctrl driver is not probed, all device drivers (including the UART driver) do a -EPROBE_DEFER, and therefore the system doesn't really boot (well, it boots, but with no UART, and no devices that require pin-muxing). Back when the Device Tree file for this board was introduced, the definition was already wrong. The pinctrl driver also always described as "gpo" this function for MPP7. However, between Linux 4.10 and 4.11, a hog pin failing to be muxed was turned from a simple warning to a hard error that caused the entire pinctrl driver probe to bail out. This is probably the result of commit6118714275
("pinctrl: core: Fix pinctrl_register_and_init() with pinctrl_enable()"). This commit fixes the Device Tree to use the proper "gpo" function for MPP7, which fixes the boot of OpenBlocks A7, which was broken since Linux 4.11. Fixes:f24b56cbcd
("ARM: kirkwood: add support for OpenBlocks A7 platform") Cc: <stable@vger.kernel.org> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit is contained in:
Родитель
4fbd8d194f
Коммит
56aeb07c91
|
@ -53,7 +53,8 @@
|
|||
};
|
||||
|
||||
pinctrl: pin-controller@10000 {
|
||||
pinctrl-0 = <&pmx_dip_switches &pmx_gpio_header>;
|
||||
pinctrl-0 = <&pmx_dip_switches &pmx_gpio_header
|
||||
&pmx_gpio_header_gpo>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
pmx_uart0: pmx-uart0 {
|
||||
|
@ -85,11 +86,16 @@
|
|||
* ground.
|
||||
*/
|
||||
pmx_gpio_header: pmx-gpio-header {
|
||||
marvell,pins = "mpp17", "mpp7", "mpp29", "mpp28",
|
||||
marvell,pins = "mpp17", "mpp29", "mpp28",
|
||||
"mpp35", "mpp34", "mpp40";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
pmx_gpio_header_gpo: pxm-gpio-header-gpo {
|
||||
marvell,pins = "mpp7";
|
||||
marvell,function = "gpo";
|
||||
};
|
||||
|
||||
pmx_gpio_init: pmx-init {
|
||||
marvell,pins = "mpp38";
|
||||
marvell,function = "gpio";
|
||||
|
|
Загрузка…
Ссылка в новой задаче