microsoft
/
WSL2-Linux-Kernel
зеркало из https://github.com/microsoft/WSL2-Linux-Kernel.git
1
0
Форкнуть 0
Код Задачи Пакеты Проекты Релизы Вики Активность

ARM: dts: at91: sama5d2: Move flx0 definitions in the SoC dtsi 

The Flexcom IP is part of the sama5d2 SoC. Move the flx0 node together
with its function definitions in sama5d2.dtsi. Boards will just fill
the pins and enable the desired functions.

There is a single functional change in this patch. With the move of the
flx0 uart5 definition in the SoC dtsi, the uart5 from
at91-sama5d27_wlsom1_ek.dts inherits the following optional property:
atmel,fifo-size = <32>;
This particular change was tested by Codrin.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-7-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This commit is contained in:
Tudor Ambarus 2020-05-14 05:03:10 +00:00 коммит произвёл Alexandre Belloni
Родитель 96f63ffdbc
Коммит 56cd4b9e8c
6 изменённых файлов: 41 добавлений и 44 удалений
Показать статистику Скачать Patch файл Скачать Diff файл Показать все файлы Свернуть все файлы

13
arch/arm/boot/dts/at91-kizbox3_common.dtsi
Просмотреть файл

@ -299,21 +299,8 @@
status = "disabled";
uart5: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x400>;
interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
| AT91_XDMAC_DT_PERID(11))>,
<&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
| AT91_XDMAC_DT_PERID(12))>;
dma-names = "tx", "rx";
clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
clock-names = "usart";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx0_default>;
atmel,fifo-size = <32>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "disabled";

12
arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts
Просмотреть файл

@ -77,18 +77,6 @@
status = "okay";
uart5: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(11))>,
<&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(12))>;
dma-names = "tx", "rx";
clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
clock-names = "usart";
pinctrl-0 = <&pinctrl_flx0_default>;
pinctrl-names = "default";
atmel,use-dma-rx;

6
arch/arm/boot/dts/at91-sama5d2_icp.dts
Просмотреть файл

@ -105,15 +105,9 @@
status = "okay";
spi2: spi@400 {
compatible = "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
clock-names = "spi_clk";
cs-gpios = <&pioA PIN_PC0 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mikrobus2_spi &pinctrl_ksz_spi_cs>;
atmel,fifo-size = <16>;
status = "okay";
#address-cells = <1>;
#size-cells = <0>;

7
arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
Просмотреть файл

@ -191,20 +191,13 @@
status = "okay";
i2c2: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <0>, <0>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_flx0_default>;
pinctrl-1 = <&pinctrl_flx0_gpio>;
sda-gpios = <&pioA PIN_PB28 GPIO_ACTIVE_HIGH>;
scl-gpios = <&pioA PIN_PB29 GPIO_ACTIVE_HIGH>;
atmel,fifo-size = <16>;
status = "okay";
};
};

7
arch/arm/boot/dts/at91-sama5d2_xplained.dts
Просмотреть файл

@ -327,14 +327,9 @@
status = "disabled"; /* conflict with ISC_D2 & ISC_D3 data pins */
uart5: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
clock-names = "usart";
dmas = <0>, <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx0_default>;
atmel,fifo-size = <32>;
status = "okay";
};
};

40
arch/arm/boot/dts/sama5d2.dtsi
Просмотреть файл

@ -635,6 +635,46 @@
#size-cells = <1>;
ranges = <0x0 0xf8034000 0x800>;
status = "disabled";
uart5: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
clock-names = "usart";
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(11))>,
<&dma0
(AT91_XDMAC_DT_MEM_IF(0) |
AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(12))>;
dma-names = "tx", "rx";
atmel,fifo-size = <32>;
status = "disabled";
};
spi2: spi@400 {
compatible = "atmel,at91rm9200-spi";
reg = <0x400 0x200>;
interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
clock-names = "spi_clk";
atmel,fifo-size = <16>;
status = "disabled";
};
i2c2: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
atmel,fifo-size = <16>;
status = "disabled";
};
};
flx1: flexcom@f8038000 {