[PATCH] e1000: Fix SoL/IDER link and loopback
Fix so that if a SoL/IDER session is active, do not allow operations which require a PHY reset and instead log a message. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: John Ronciak <john.ronciak@intel.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This commit is contained in:
Родитель
545c67c0a3
Коммит
571281972e
|
@ -183,7 +183,15 @@ e1000_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
|
|||
struct e1000_adapter *adapter = netdev_priv(netdev);
|
||||
struct e1000_hw *hw = &adapter->hw;
|
||||
|
||||
if(ecmd->autoneg == AUTONEG_ENABLE) {
|
||||
/* When SoL/IDER sessions are active, autoneg/speed/duplex
|
||||
* cannot be changed */
|
||||
if (e1000_check_phy_reset_block(hw)) {
|
||||
DPRINTK(DRV, ERR, "Cannot change link characteristics "
|
||||
"when SoL/IDER is active.\n");
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
if (ecmd->autoneg == AUTONEG_ENABLE) {
|
||||
hw->autoneg = 1;
|
||||
if(hw->media_type == e1000_media_type_fiber)
|
||||
hw->autoneg_advertised = ADVERTISED_1000baseT_Full |
|
||||
|
@ -562,29 +570,10 @@ e1000_get_drvinfo(struct net_device *netdev,
|
|||
struct ethtool_drvinfo *drvinfo)
|
||||
{
|
||||
struct e1000_adapter *adapter = netdev_priv(netdev);
|
||||
char firmware_version[32];
|
||||
uint16_t eeprom_data;
|
||||
|
||||
strncpy(drvinfo->driver, e1000_driver_name, 32);
|
||||
strncpy(drvinfo->version, e1000_driver_version, 32);
|
||||
|
||||
/* EEPROM image version # is reported as firware version # for
|
||||
* 8257{1|2|3} controllers */
|
||||
e1000_read_eeprom(&adapter->hw, 5, 1, &eeprom_data);
|
||||
switch (adapter->hw.mac_type) {
|
||||
case e1000_82571:
|
||||
case e1000_82572:
|
||||
case e1000_82573:
|
||||
sprintf(firmware_version, "%d.%d-%d",
|
||||
(eeprom_data & 0xF000) >> 12,
|
||||
(eeprom_data & 0x0FF0) >> 4,
|
||||
eeprom_data & 0x000F);
|
||||
break;
|
||||
default:
|
||||
sprintf(firmware_version, "n/a");
|
||||
}
|
||||
|
||||
strncpy(drvinfo->fw_version, firmware_version, 32);
|
||||
strncpy(drvinfo->fw_version, "N/A", 32);
|
||||
strncpy(drvinfo->bus_info, pci_name(adapter->pdev), 32);
|
||||
drvinfo->n_stats = E1000_STATS_LEN;
|
||||
drvinfo->testinfo_len = E1000_TEST_LEN;
|
||||
|
@ -990,10 +979,8 @@ e1000_free_desc_rings(struct e1000_adapter *adapter)
|
|||
|
||||
kfree(txdr->buffer_info);
|
||||
txdr->buffer_info = NULL;
|
||||
|
||||
kfree(rxdr->buffer_info);
|
||||
rxdr->buffer_info = NULL;
|
||||
|
||||
return;
|
||||
}
|
||||
|
||||
|
@ -1328,32 +1315,21 @@ static int
|
|||
e1000_setup_loopback_test(struct e1000_adapter *adapter)
|
||||
{
|
||||
uint32_t rctl;
|
||||
struct e1000_hw *hw = &adapter->hw;
|
||||
|
||||
if (hw->media_type == e1000_media_type_fiber ||
|
||||
hw->media_type == e1000_media_type_internal_serdes) {
|
||||
switch (hw->mac_type) {
|
||||
case e1000_82545:
|
||||
case e1000_82546:
|
||||
case e1000_82545_rev_3:
|
||||
case e1000_82546_rev_3:
|
||||
if(adapter->hw.media_type == e1000_media_type_fiber ||
|
||||
adapter->hw.media_type == e1000_media_type_internal_serdes) {
|
||||
if(adapter->hw.mac_type == e1000_82545 ||
|
||||
adapter->hw.mac_type == e1000_82546 ||
|
||||
adapter->hw.mac_type == e1000_82545_rev_3 ||
|
||||
adapter->hw.mac_type == e1000_82546_rev_3)
|
||||
return e1000_set_phy_loopback(adapter);
|
||||
break;
|
||||
case e1000_82571:
|
||||
case e1000_82572:
|
||||
#define E1000_SERDES_LB_ON 0x410
|
||||
e1000_set_phy_loopback(adapter);
|
||||
E1000_WRITE_REG(hw, SCTL, E1000_SERDES_LB_ON);
|
||||
msec_delay(10);
|
||||
return 0;
|
||||
break;
|
||||
default:
|
||||
rctl = E1000_READ_REG(hw, RCTL);
|
||||
else {
|
||||
rctl = E1000_READ_REG(&adapter->hw, RCTL);
|
||||
rctl |= E1000_RCTL_LBM_TCVR;
|
||||
E1000_WRITE_REG(hw, RCTL, rctl);
|
||||
E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
|
||||
return 0;
|
||||
}
|
||||
} else if (hw->media_type == e1000_media_type_copper)
|
||||
} else if(adapter->hw.media_type == e1000_media_type_copper)
|
||||
return e1000_set_phy_loopback(adapter);
|
||||
|
||||
return 7;
|
||||
|
@ -1364,36 +1340,25 @@ e1000_loopback_cleanup(struct e1000_adapter *adapter)
|
|||
{
|
||||
uint32_t rctl;
|
||||
uint16_t phy_reg;
|
||||
struct e1000_hw *hw = &adapter->hw;
|
||||
|
||||
rctl = E1000_READ_REG(&adapter->hw, RCTL);
|
||||
rctl &= ~(E1000_RCTL_LBM_TCVR | E1000_RCTL_LBM_MAC);
|
||||
E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
|
||||
|
||||
switch (hw->mac_type) {
|
||||
case e1000_82571:
|
||||
case e1000_82572:
|
||||
if (hw->media_type == e1000_media_type_fiber ||
|
||||
hw->media_type == e1000_media_type_internal_serdes){
|
||||
#define E1000_SERDES_LB_OFF 0x400
|
||||
E1000_WRITE_REG(hw, SCTL, E1000_SERDES_LB_OFF);
|
||||
msec_delay(10);
|
||||
break;
|
||||
}
|
||||
/* fall thru for Cu adapters */
|
||||
case e1000_82545:
|
||||
case e1000_82546:
|
||||
case e1000_82545_rev_3:
|
||||
case e1000_82546_rev_3:
|
||||
default:
|
||||
hw->autoneg = TRUE;
|
||||
e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg);
|
||||
if (phy_reg & MII_CR_LOOPBACK) {
|
||||
if(adapter->hw.media_type == e1000_media_type_copper ||
|
||||
((adapter->hw.media_type == e1000_media_type_fiber ||
|
||||
adapter->hw.media_type == e1000_media_type_internal_serdes) &&
|
||||
(adapter->hw.mac_type == e1000_82545 ||
|
||||
adapter->hw.mac_type == e1000_82546 ||
|
||||
adapter->hw.mac_type == e1000_82545_rev_3 ||
|
||||
adapter->hw.mac_type == e1000_82546_rev_3))) {
|
||||
adapter->hw.autoneg = TRUE;
|
||||
e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &phy_reg);
|
||||
if(phy_reg & MII_CR_LOOPBACK) {
|
||||
phy_reg &= ~MII_CR_LOOPBACK;
|
||||
e1000_write_phy_reg(hw, PHY_CTRL, phy_reg);
|
||||
e1000_phy_reset(hw);
|
||||
e1000_write_phy_reg(&adapter->hw, PHY_CTRL, phy_reg);
|
||||
e1000_phy_reset(&adapter->hw);
|
||||
}
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
|
@ -1488,14 +1453,25 @@ e1000_run_loopback_test(struct e1000_adapter *adapter)
|
|||
static int
|
||||
e1000_loopback_test(struct e1000_adapter *adapter, uint64_t *data)
|
||||
{
|
||||
if((*data = e1000_setup_desc_rings(adapter))) goto err_loopback;
|
||||
if((*data = e1000_setup_loopback_test(adapter)))
|
||||
goto err_loopback_setup;
|
||||
/* PHY loopback cannot be performed if SoL/IDER
|
||||
* sessions are active */
|
||||
if (e1000_check_phy_reset_block(&adapter->hw)) {
|
||||
DPRINTK(DRV, ERR, "Cannot do PHY loopback test "
|
||||
"when SoL/IDER is active.\n");
|
||||
*data = 0;
|
||||
goto out;
|
||||
}
|
||||
|
||||
if ((*data = e1000_setup_desc_rings(adapter)))
|
||||
goto out;
|
||||
if ((*data = e1000_setup_loopback_test(adapter)))
|
||||
goto err_loopback;
|
||||
*data = e1000_run_loopback_test(adapter);
|
||||
e1000_loopback_cleanup(adapter);
|
||||
err_loopback_setup:
|
||||
e1000_free_desc_rings(adapter);
|
||||
|
||||
err_loopback:
|
||||
e1000_free_desc_rings(adapter);
|
||||
out:
|
||||
return *data;
|
||||
}
|
||||
|
||||
|
@ -1722,14 +1698,6 @@ e1000_phys_id(struct net_device *netdev, uint32_t data)
|
|||
msleep_interruptible(data * 1000);
|
||||
del_timer_sync(&adapter->blink_timer);
|
||||
}
|
||||
else if(adapter->hw.mac_type < e1000_82573) {
|
||||
E1000_WRITE_REG(&adapter->hw, LEDCTL, (E1000_LEDCTL_LED2_BLINK_RATE |
|
||||
E1000_LEDCTL_LED0_BLINK | E1000_LEDCTL_LED2_BLINK |
|
||||
(E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED2_MODE_SHIFT) |
|
||||
(E1000_LEDCTL_MODE_LINK_ACTIVITY << E1000_LEDCTL_LED0_MODE_SHIFT) |
|
||||
(E1000_LEDCTL_MODE_LED_OFF << E1000_LEDCTL_LED1_MODE_SHIFT)));
|
||||
msleep_interruptible(data * 1000);
|
||||
}
|
||||
else {
|
||||
E1000_WRITE_REG(&adapter->hw, LEDCTL, (E1000_LEDCTL_LED2_BLINK_RATE |
|
||||
E1000_LEDCTL_LED1_BLINK | E1000_LEDCTL_LED2_BLINK |
|
||||
|
|
|
@ -378,6 +378,8 @@ void
|
|||
e1000_down(struct e1000_adapter *adapter)
|
||||
{
|
||||
struct net_device *netdev = adapter->netdev;
|
||||
boolean_t mng_mode_enabled = (adapter->hw.mac_type >= e1000_82571) &&
|
||||
e1000_check_mng_mode(&adapter->hw);
|
||||
|
||||
e1000_irq_disable(adapter);
|
||||
#ifdef CONFIG_E1000_MQ
|
||||
|
@ -405,12 +407,16 @@ e1000_down(struct e1000_adapter *adapter)
|
|||
e1000_clean_all_tx_rings(adapter);
|
||||
e1000_clean_all_rx_rings(adapter);
|
||||
|
||||
/* If WoL is not enabled and management mode is not IAMT
|
||||
* Power down the PHY so no link is implied when interface is down */
|
||||
if(!adapter->wol && adapter->hw.mac_type >= e1000_82540 &&
|
||||
/* Power down the PHY so no link is implied when interface is down *
|
||||
* The PHY cannot be powered down if any of the following is TRUE *
|
||||
* (a) WoL is enabled
|
||||
* (b) AMT is active
|
||||
* (c) SoL/IDER session is active */
|
||||
if (!adapter->wol && adapter->hw.mac_type >= e1000_82540 &&
|
||||
adapter->hw.media_type == e1000_media_type_copper &&
|
||||
!e1000_check_mng_mode(&adapter->hw) &&
|
||||
!(E1000_READ_REG(&adapter->hw, MANC) & E1000_MANC_SMBUS_EN)) {
|
||||
!(E1000_READ_REG(&adapter->hw, MANC) & E1000_MANC_SMBUS_EN) &&
|
||||
!mng_mode_enabled &&
|
||||
!e1000_check_phy_reset_block(&adapter->hw)) {
|
||||
uint16_t mii_reg;
|
||||
e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &mii_reg);
|
||||
mii_reg |= MII_CR_POWER_DOWN;
|
||||
|
|
|
@ -584,6 +584,12 @@ e1000_check_copper_options(struct e1000_adapter *adapter)
|
|||
.p = dplx_list }}
|
||||
};
|
||||
|
||||
if (e1000_check_phy_reset_block(&adapter->hw)) {
|
||||
DPRINTK(PROBE, INFO,
|
||||
"Link active due to SoL/IDER Session. "
|
||||
"Speed/Duplex/AutoNeg parameter ignored.\n");
|
||||
return;
|
||||
}
|
||||
if (num_Duplex > bd) {
|
||||
dplx = Duplex[bd];
|
||||
e1000_validate_option(&dplx, &opt, adapter);
|
||||
|
|
Загрузка…
Ссылка в новой задаче