dmaengine: ste_dma40: Get LCPA SRAM from SRAM node

Instead of passing the reserved SRAM as a "reg" field
look for a phandle to the LCPA SRAM memory so we can
use the proper SRAM device tree bindings for the SRAM.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230417-ux500-dma40-cleanup-v3-2-60bfa6785968@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

drivers/dma/Kconfig

@@ -553,6 +553,7 @@ config STE_DMA40
 	bool "ST-Ericsson DMA40 support"
 	depends on ARCH_U8500
 	select DMA_ENGINE
+	select SRAM
 	help
 	  Support for ST-Ericsson DMA40 controller
 

drivers/dma/ste_dma40.c

@@ -19,6 +19,7 @@
 #include <linux/pm_runtime.h>
 #include <linux/err.h>
 #include <linux/of.h>
+#include <linux/of_address.h>
 #include <linux/of_dma.h>
 #include <linux/amba/bus.h>
 #include <linux/regulator/consumer.h>
@@ -3506,9 +3507,11 @@ static int __init d40_probe(struct platform_device *pdev)
 {
 	struct stedma40_platform_data *plat_data = dev_get_platdata(&pdev->dev);
 	struct device_node *np = pdev->dev.of_node;
+	struct device_node *np_lcpa;
 	int ret = -ENOENT;
 	struct d40_base *base;
 	struct resource *res;
+	struct resource res_lcpa;
 	int num_reserved_chans;
 	u32 val;
 
@@ -3535,37 +3538,37 @@ static int __init d40_probe(struct platform_device *pdev)
 	spin_lock_init(&base->interrupt_lock);
 	spin_lock_init(&base->execmd_lock);
 
-	/* Get IO for logical channel parameter address */
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "lcpa");
-	if (!res) {
-		ret = -ENOENT;
-		d40_err(&pdev->dev, "No \"lcpa\" memory resource\n");
-		goto destroy_cache;
+	/* Get IO for logical channel parameter address (LCPA) */
+	np_lcpa = of_parse_phandle(np, "sram", 0);
+	if (!np_lcpa) {
+		dev_err(&pdev->dev, "no LCPA SRAM node\n");
+		goto report_failure;
 	}
-	base->lcpa_size = resource_size(res);
-	base->phy_lcpa = res->start;
-
-	if (request_mem_region(res->start, resource_size(res),
-			       D40_NAME " I/O lcpa") == NULL) {
-		ret = -EBUSY;
-		d40_err(&pdev->dev, "Failed to request LCPA region %pR\n", res);
-		goto destroy_cache;
+	/* This is no device so read the address directly from the node */
+	ret = of_address_to_resource(np_lcpa, 0, &res_lcpa);
+	if (ret) {
+		dev_err(&pdev->dev, "no LCPA SRAM resource\n");
+		goto report_failure;
 	}
+	base->lcpa_size = resource_size(&res_lcpa);
+	base->phy_lcpa = res_lcpa.start;
+	dev_info(&pdev->dev, "found LCPA SRAM at 0x%08x, size 0x%08x\n",
+		 (u32)base->phy_lcpa, base->lcpa_size);
 
 	/* We make use of ESRAM memory for this. */
 	val = readl(base->virtbase + D40_DREG_LCPA);
-	if (res->start != val && val != 0) {
+	if (base->phy_lcpa != val && val != 0) {
 		dev_warn(&pdev->dev,
-			 "[%s] Mismatch LCPA dma 0x%x, def %pa\n",
-			 __func__, val, &res->start);
+			 "[%s] Mismatch LCPA dma 0x%x, def %08x\n",
+			 __func__, val, (u32)base->phy_lcpa);
 	} else
-		writel(res->start, base->virtbase + D40_DREG_LCPA);
+		writel(base->phy_lcpa, base->virtbase + D40_DREG_LCPA);
 
-	base->lcpa_base = ioremap(res->start, resource_size(res));
+	base->lcpa_base = ioremap(base->phy_lcpa, base->lcpa_size);
 	if (!base->lcpa_base) {
 		ret = -ENOMEM;
 		d40_err(&pdev->dev, "Failed to ioremap LCPA region\n");
-		goto destroy_cache;
+		goto release_base;
 	}
 	/* If lcla has to be located in ESRAM we don't need to allocate */
 	if (base->plat_data->use_esram_lcla) {
@@ -3678,9 +3681,7 @@ static int __init d40_probe(struct platform_device *pdev)
 	if (base->lcpa_base)
 		iounmap(base->lcpa_base);
 
-	if (base->phy_lcpa)
-		release_mem_region(base->phy_lcpa,
-				   base->lcpa_size);
+release_base:
 	if (base->phy_start)
 		release_mem_region(base->phy_start,
 				   base->phy_size);