Blackfin: tcm-bf518: new board port
Signed-off-by: Harald Krapfenbauer <harald.krapfenbauer@bluetechnix.at> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This commit is contained in:
Harald Krapfenbauer
Mike Frysinger
Родитель
38e7673f24
Коммит
5aff1642ae
Разница между файлами не показана из-за своего большого размера
Загрузить разницу
|
|
@ -9,4 +9,9 @@ config BFIN518F_EZBRD
|
|||
help
|
||||
BF518-EZBRD board support.
|
||||
|
||||
config BFIN518F_TCM
|
||||
bool "Bluetechnix TCM-BF518"
|
||||
help
|
||||
Bluetechnix TCM-BF518 board support.
|
||||
|
||||
endchoice
|
||||
|
|
|
|||
|
|
@ -3,3 +3,4 @@
|
|||
#
|
||||
|
||||
obj-$(CONFIG_BFIN518F_EZBRD) += ezbrd.o
|
||||
obj-$(CONFIG_BFIN518F_TCM) += tcm-bf518.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,753 @@
|
|||
/*
|
||||
* Copyright 2004-2009 Analog Devices Inc.
|
||||
* 2005 National ICT Australia (NICTA)
|
||||
* Aidan Williams <aidan@nicta.com.au>
|
||||
*
|
||||
* Licensed under the GPL-2 or later.
|
||||
*/
|
||||
|
||||
#include <linux/device.h>
|
||||
#include <linux/etherdevice.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/mtd/mtd.h>
|
||||
#include <linux/mtd/partitions.h>
|
||||
#include <linux/mtd/physmap.h>
|
||||
#include <linux/spi/spi.h>
|
||||
#include <linux/spi/flash.h>
|
||||
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/irq.h>
|
||||
#include <linux/interrupt.h>
|
||||
#include <asm/dma.h>
|
||||
#include <asm/bfin5xx_spi.h>
|
||||
#include <asm/reboot.h>
|
||||
#include <asm/portmux.h>
|
||||
#include <asm/dpmc.h>
|
||||
#include <asm/bfin_sdh.h>
|
||||
#include <linux/spi/ad7877.h>
|
||||
#include <net/dsa.h>
|
||||
|
||||
/*
|
||||
* Name the Board for the /proc/cpuinfo
|
||||
*/
|
||||
const char bfin_board_name[] = "Bluetechnix TCM-BF518";
|
||||
|
||||
/*
|
||||
* Driver needs to know address, irq and flag pin.
|
||||
*/
|
||||
|
||||
#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
|
||||
static struct mtd_partition tcm_partitions[] = {
|
||||
{
|
||||
.name = "bootloader(nor)",
|
||||
.size = 0x40000,
|
||||
.offset = 0,
|
||||
},
|
||||
{
|
||||
.name = "linux(nor)",
|
||||
.size = 0x1C0000,
|
||||
.offset = MTDPART_OFS_APPEND,
|
||||
}
|
||||
};
|
||||
|
||||
static struct physmap_flash_data tcm_flash_data = {
|
||||
.width = 2,
|
||||
.parts = tcm_partitions,
|
||||
.nr_parts = ARRAY_SIZE(tcm_partitions),
|
||||
};
|
||||
|
||||
static struct resource tcm_flash_resource = {
|
||||
.start = 0x20000000,
|
||||
.end = 0x201fffff,
|
||||
.flags = IORESOURCE_MEM,
|
||||
};
|
||||
|
||||
static struct platform_device tcm_flash_device = {
|
||||
.name = "physmap-flash",
|
||||
.id = 0,
|
||||
.dev = {
|
||||
.platform_data = &tcm_flash_data,
|
||||
},
|
||||
.num_resources = 1,
|
||||
.resource = &tcm_flash_resource,
|
||||
};
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
|
||||
static struct platform_device rtc_device = {
|
||||
.name = "rtc-bfin",
|
||||
.id = -1,
|
||||
};
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
|
||||
static struct platform_device bfin_mii_bus = {
|
||||
.name = "bfin_mii_bus",
|
||||
};
|
||||
|
||||
static struct platform_device bfin_mac_device = {
|
||||
.name = "bfin_mac",
|
||||
.dev.platform_data = &bfin_mii_bus,
|
||||
};
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_MTD_M25P80) \
|
||||
|| defined(CONFIG_MTD_M25P80_MODULE)
|
||||
static struct mtd_partition bfin_spi_flash_partitions[] = {
|
||||
{
|
||||
.name = "bootloader(spi)",
|
||||
.size = 0x00040000,
|
||||
.offset = 0,
|
||||
.mask_flags = MTD_CAP_ROM
|
||||
}, {
|
||||
.name = "linux kernel(spi)",
|
||||
.size = MTDPART_SIZ_FULL,
|
||||
.offset = MTDPART_OFS_APPEND,
|
||||
}
|
||||
};
|
||||
|
||||
static struct flash_platform_data bfin_spi_flash_data = {
|
||||
.name = "m25p80",
|
||||
.parts = bfin_spi_flash_partitions,
|
||||
.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
|
||||
.type = "m25p16",
|
||||
};
|
||||
|
||||
/* SPI flash chip (m25p64) */
|
||||
static struct bfin5xx_spi_chip spi_flash_chip_info = {
|
||||
.enable_dma = 0, /* use dma transfer with this chip*/
|
||||
.bits_per_word = 8,
|
||||
};
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_BFIN_SPI_ADC) \
|
||||
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
|
||||
/* SPI ADC chip */
|
||||
static struct bfin5xx_spi_chip spi_adc_chip_info = {
|
||||
.enable_dma = 1, /* use dma transfer with this chip*/
|
||||
.bits_per_word = 16,
|
||||
};
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
|
||||
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
|
||||
.enable_dma = 0,
|
||||
.bits_per_word = 8,
|
||||
};
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
|
||||
static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
|
||||
.enable_dma = 0,
|
||||
.bits_per_word = 16,
|
||||
};
|
||||
|
||||
static const struct ad7877_platform_data bfin_ad7877_ts_info = {
|
||||
.model = 7877,
|
||||
.vref_delay_usecs = 50, /* internal, no capacitor */
|
||||
.x_plate_ohms = 419,
|
||||
.y_plate_ohms = 486,
|
||||
.pressure_max = 1000,
|
||||
.pressure_min = 0,
|
||||
.stopacq_polarity = 1,
|
||||
.first_conversion_delay = 3,
|
||||
.acquisition_time = 1,
|
||||
.averaging = 1,
|
||||
.pen_down_acc_interval = 1,
|
||||
};
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
|
||||
&& defined(CONFIG_SND_SOC_WM8731_SPI)
|
||||
static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
|
||||
.enable_dma = 0,
|
||||
.bits_per_word = 16,
|
||||
};
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
|
||||
static struct bfin5xx_spi_chip spidev_chip_info = {
|
||||
.enable_dma = 0,
|
||||
.bits_per_word = 8,
|
||||
};
|
||||
#endif
|
||||
|
||||
static struct spi_board_info bfin_spi_board_info[] __initdata = {
|
||||
#if defined(CONFIG_MTD_M25P80) \
|
||||
|| defined(CONFIG_MTD_M25P80_MODULE)
|
||||
{
|
||||
/* the modalias must be the same as spi device driver name */
|
||||
.modalias = "m25p80", /* Name of spi_driver for this device */
|
||||
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
|
||||
.bus_num = 0, /* Framework bus number */
|
||||
.chip_select = 2, /* SPI0_SSEL2 */
|
||||
.platform_data = &bfin_spi_flash_data,
|
||||
.controller_data = &spi_flash_chip_info,
|
||||
.mode = SPI_MODE_3,
|
||||
},
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_BFIN_SPI_ADC) \
|
||||
|| defined(CONFIG_BFIN_SPI_ADC_MODULE)
|
||||
{
|
||||
.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
|
||||
.max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
|
||||
.bus_num = 0, /* Framework bus number */
|
||||
.chip_select = 1, /* Framework chip select. */
|
||||
.platform_data = NULL, /* No spi_driver specific config */
|
||||
.controller_data = &spi_adc_chip_info,
|
||||
},
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
|
||||
{
|
||||
.modalias = "mmc_spi",
|
||||
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
|
||||
.bus_num = 0,
|
||||
.chip_select = 5,
|
||||
.controller_data = &mmc_spi_chip_info,
|
||||
.mode = SPI_MODE_3,
|
||||
},
|
||||
#endif
|
||||
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
|
||||
{
|
||||
.modalias = "ad7877",
|
||||
.platform_data = &bfin_ad7877_ts_info,
|
||||
.irq = IRQ_PF8,
|
||||
.max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
|
||||
.bus_num = 0,
|
||||
.chip_select = 2,
|
||||
.controller_data = &spi_ad7877_chip_info,
|
||||
},
|
||||
#endif
|
||||
#if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
|
||||
&& defined(CONFIG_SND_SOC_WM8731_SPI)
|
||||
{
|
||||
.modalias = "wm8731",
|
||||
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
|
||||
.bus_num = 0,
|
||||
.chip_select = 5,
|
||||
.controller_data = &spi_wm8731_chip_info,
|
||||
.mode = SPI_MODE_0,
|
||||
},
|
||||
#endif
|
||||
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
|
||||
{
|
||||
.modalias = "spidev",
|
||||
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
|
||||
.bus_num = 0,
|
||||
.chip_select = 1,
|
||||
.controller_data = &spidev_chip_info,
|
||||
},
|
||||
#endif
|
||||
#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
|
||||
{
|
||||
.modalias = "bfin-lq035q1-spi",
|
||||
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
|
||||
.bus_num = 0,
|
||||
.chip_select = 1,
|
||||
.controller_data = &lq035q1_spi_chip_info,
|
||||
.mode = SPI_CPHA | SPI_CPOL,
|
||||
},
|
||||
#endif
|
||||
};
|
||||
|
||||
/* SPI controller data */
|
||||
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
|
||||
/* SPI (0) */
|
||||
static struct bfin5xx_spi_master bfin_spi0_info = {
|
||||
.num_chipselect = 6,
|
||||
.enable_dma = 1, /* master has the ability to do dma transfer */
|
||||
.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
|
||||
};
|
||||
|
||||
static struct resource bfin_spi0_resource[] = {
|
||||
[0] = {
|
||||
.start = SPI0_REGBASE,
|
||||
.end = SPI0_REGBASE + 0xFF,
|
||||
.flags = IORESOURCE_MEM,
|
||||
},
|
||||
[1] = {
|
||||
.start = CH_SPI0,
|
||||
.end = CH_SPI0,
|
||||
.flags = IORESOURCE_DMA,
|
||||
},
|
||||
[2] = {
|
||||
.start = IRQ_SPI0,
|
||||
.end = IRQ_SPI0,
|
||||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
};
|
||||
|
||||
static struct platform_device bfin_spi0_device = {
|
||||
.name = "bfin-spi",
|
||||
.id = 0, /* Bus number */
|
||||
.num_resources = ARRAY_SIZE(bfin_spi0_resource),
|
||||
.resource = bfin_spi0_resource,
|
||||
.dev = {
|
||||
.platform_data = &bfin_spi0_info, /* Passed to driver */
|
||||
},
|
||||
};
|
||||
|
||||
/* SPI (1) */
|
||||
static struct bfin5xx_spi_master bfin_spi1_info = {
|
||||
.num_chipselect = 5,
|
||||
.enable_dma = 1, /* master has the ability to do dma transfer */
|
||||
.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
|
||||
};
|
||||
|
||||
static struct resource bfin_spi1_resource[] = {
|
||||
[0] = {
|
||||
.start = SPI1_REGBASE,
|
||||
.end = SPI1_REGBASE + 0xFF,
|
||||
.flags = IORESOURCE_MEM,
|
||||
},
|
||||
[1] = {
|
||||
.start = CH_SPI1,
|
||||
.end = CH_SPI1,
|
||||
.flags = IORESOURCE_DMA,
|
||||
},
|
||||
[2] = {
|
||||
.start = IRQ_SPI1,
|
||||
.end = IRQ_SPI1,
|
||||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
};
|
||||
|
||||
static struct platform_device bfin_spi1_device = {
|
||||
.name = "bfin-spi",
|
||||
.id = 1, /* Bus number */
|
||||
.num_resources = ARRAY_SIZE(bfin_spi1_resource),
|
||||
.resource = bfin_spi1_resource,
|
||||
.dev = {
|
||||
.platform_data = &bfin_spi1_info, /* Passed to driver */
|
||||
},
|
||||
};
|
||||
#endif /* spi master and devices */
|
||||
|
||||
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
|
||||
#ifdef CONFIG_SERIAL_BFIN_UART0
|
||||
static struct resource bfin_uart0_resources[] = {
|
||||
{
|
||||
.start = UART0_THR,
|
||||
.end = UART0_GCTL+2,
|
||||
.flags = IORESOURCE_MEM,
|
||||
},
|
||||
{
|
||||
.start = IRQ_UART0_RX,
|
||||
.end = IRQ_UART0_RX+1,
|
||||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
{
|
||||
.start = IRQ_UART0_ERROR,
|
||||
.end = IRQ_UART0_ERROR,
|
||||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
{
|
||||
.start = CH_UART0_TX,
|
||||
.end = CH_UART0_TX,
|
||||
.flags = IORESOURCE_DMA,
|
||||
},
|
||||
{
|
||||
.start = CH_UART0_RX,
|
||||
.end = CH_UART0_RX,
|
||||
.flags = IORESOURCE_DMA,
|
||||
},
|
||||
};
|
||||
|
||||
unsigned short bfin_uart0_peripherals[] = {
|
||||
P_UART0_TX, P_UART0_RX, 0
|
||||
};
|
||||
|
||||
static struct platform_device bfin_uart0_device = {
|
||||
.name = "bfin-uart",
|
||||
.id = 0,
|
||||
.num_resources = ARRAY_SIZE(bfin_uart0_resources),
|
||||
.resource = bfin_uart0_resources,
|
||||
.dev = {
|
||||
.platform_data = &bfin_uart0_peripherals, /* Passed to driver */
|
||||
},
|
||||
};
|
||||
#endif
|
||||
#ifdef CONFIG_SERIAL_BFIN_UART1
|
||||
static struct resource bfin_uart1_resources[] = {
|
||||
{
|
||||
.start = UART1_THR,
|
||||
.end = UART1_GCTL+2,
|
||||
.flags = IORESOURCE_MEM,
|
||||
},
|
||||
{
|
||||
.start = IRQ_UART1_RX,
|
||||
.end = IRQ_UART1_RX+1,
|
||||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
{
|
||||
.start = IRQ_UART1_ERROR,
|
||||
.end = IRQ_UART1_ERROR,
|
||||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
{
|
||||
.start = CH_UART1_TX,
|
||||
.end = CH_UART1_TX,
|
||||
.flags = IORESOURCE_DMA,
|
||||
},
|
||||
{
|
||||
.start = CH_UART1_RX,
|
||||
.end = CH_UART1_RX,
|
||||
.flags = IORESOURCE_DMA,
|
||||
},
|
||||
};
|
||||
|
||||
unsigned short bfin_uart1_peripherals[] = {
|
||||
P_UART1_TX, P_UART1_RX, 0
|
||||
};
|
||||
|
||||
static struct platform_device bfin_uart1_device = {
|
||||
.name = "bfin-uart",
|
||||
.id = 1,
|
||||
.num_resources = ARRAY_SIZE(bfin_uart1_resources),
|
||||
.resource = bfin_uart1_resources,
|
||||
.dev = {
|
||||
.platform_data = &bfin_uart1_peripherals, /* Passed to driver */
|
||||
},
|
||||
};
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
|
||||
#ifdef CONFIG_BFIN_SIR0
|
||||
static struct resource bfin_sir0_resources[] = {
|
||||
{
|
||||
.start = 0xFFC00400,
|
||||
.end = 0xFFC004FF,
|
||||
.flags = IORESOURCE_MEM,
|
||||
},
|
||||
{
|
||||
.start = IRQ_UART0_RX,
|
||||
.end = IRQ_UART0_RX+1,
|
||||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
{
|
||||
.start = CH_UART0_RX,
|
||||
.end = CH_UART0_RX+1,
|
||||
.flags = IORESOURCE_DMA,
|
||||
},
|
||||
};
|
||||
|
||||
static struct platform_device bfin_sir0_device = {
|
||||
.name = "bfin_sir",
|
||||
.id = 0,
|
||||
.num_resources = ARRAY_SIZE(bfin_sir0_resources),
|
||||
.resource = bfin_sir0_resources,
|
||||
};
|
||||
#endif
|
||||
#ifdef CONFIG_BFIN_SIR1
|
||||
static struct resource bfin_sir1_resources[] = {
|
||||
{
|
||||
.start = 0xFFC02000,
|
||||
.end = 0xFFC020FF,
|
||||
.flags = IORESOURCE_MEM,
|
||||
},
|
||||
{
|
||||
.start = IRQ_UART1_RX,
|
||||
.end = IRQ_UART1_RX+1,
|
||||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
{
|
||||
.start = CH_UART1_RX,
|
||||
.end = CH_UART1_RX+1,
|
||||
.flags = IORESOURCE_DMA,
|
||||
},
|
||||
};
|
||||
|
||||
static struct platform_device bfin_sir1_device = {
|
||||
.name = "bfin_sir",
|
||||
.id = 1,
|
||||
.num_resources = ARRAY_SIZE(bfin_sir1_resources),
|
||||
.resource = bfin_sir1_resources,
|
||||
};
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
|
||||
static struct resource bfin_twi0_resource[] = {
|
||||
[0] = {
|
||||
.start = TWI0_REGBASE,
|
||||
.end = TWI0_REGBASE,
|
||||
.flags = IORESOURCE_MEM,
|
||||
},
|
||||
[1] = {
|
||||
.start = IRQ_TWI,
|
||||
.end = IRQ_TWI,
|
||||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
};
|
||||
|
||||
static struct platform_device i2c_bfin_twi_device = {
|
||||
.name = "i2c-bfin-twi",
|
||||
.id = 0,
|
||||
.num_resources = ARRAY_SIZE(bfin_twi0_resource),
|
||||
.resource = bfin_twi0_resource,
|
||||
};
|
||||
#endif
|
||||
|
||||
static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
|
||||
#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
|
||||
{
|
||||
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
|
||||
},
|
||||
#endif
|
||||
#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
|
||||
{
|
||||
I2C_BOARD_INFO("pcf8574_keypad", 0x27),
|
||||
.irq = IRQ_PF8,
|
||||
},
|
||||
#endif
|
||||
};
|
||||
|
||||
#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
|
||||
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
|
||||
static struct resource bfin_sport0_uart_resources[] = {
|
||||
{
|
||||
.start = SPORT0_TCR1,
|
||||
.end = SPORT0_MRCS3+4,
|
||||
.flags = IORESOURCE_MEM,
|
||||
},
|
||||
{
|
||||
.start = IRQ_SPORT0_RX,
|
||||
.end = IRQ_SPORT0_RX+1,
|
||||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
{
|
||||
.start = IRQ_SPORT0_ERROR,
|
||||
.end = IRQ_SPORT0_ERROR,
|
||||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
};
|
||||
|
||||
unsigned short bfin_sport0_peripherals[] = {
|
||||
P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
|
||||
P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
|
||||
};
|
||||
|
||||
static struct platform_device bfin_sport0_uart_device = {
|
||||
.name = "bfin-sport-uart",
|
||||
.id = 0,
|
||||
.num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
|
||||
.resource = bfin_sport0_uart_resources,
|
||||
.dev = {
|
||||
.platform_data = &bfin_sport0_peripherals, /* Passed to driver */
|
||||
},
|
||||
};
|
||||
#endif
|
||||
#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
|
||||
static struct resource bfin_sport1_uart_resources[] = {
|
||||
{
|
||||
.start = SPORT1_TCR1,
|
||||
.end = SPORT1_MRCS3+4,
|
||||
.flags = IORESOURCE_MEM,
|
||||
},
|
||||
{
|
||||
.start = IRQ_SPORT1_RX,
|
||||
.end = IRQ_SPORT1_RX+1,
|
||||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
{
|
||||
.start = IRQ_SPORT1_ERROR,
|
||||
.end = IRQ_SPORT1_ERROR,
|
||||
.flags = IORESOURCE_IRQ,
|
||||
},
|
||||
};
|
||||
|
||||
unsigned short bfin_sport1_peripherals[] = {
|
||||
P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
|
||||
P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0
|
||||
};
|
||||
|
||||
static struct platform_device bfin_sport1_uart_device = {
|
||||
.name = "bfin-sport-uart",
|
||||
.id = 1,
|
||||
.num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
|
||||
.resource = bfin_sport1_uart_resources,
|
||||
.dev = {
|
||||
.platform_data = &bfin_sport1_peripherals, /* Passed to driver */
|
||||
},
|
||||
};
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
|
||||
#include <linux/input.h>
|
||||
#include <linux/gpio_keys.h>
|
||||
|
||||
static struct gpio_keys_button bfin_gpio_keys_table[] = {
|
||||
{BTN_0, GPIO_PG0, 1, "gpio-keys: BTN0"},
|
||||
{BTN_1, GPIO_PG13, 1, "gpio-keys: BTN1"},
|
||||
};
|
||||
|
||||
static struct gpio_keys_platform_data bfin_gpio_keys_data = {
|
||||
.buttons = bfin_gpio_keys_table,
|
||||
.nbuttons = ARRAY_SIZE(bfin_gpio_keys_table),
|
||||
};
|
||||
|
||||
static struct platform_device bfin_device_gpiokeys = {
|
||||
.name = "gpio-keys",
|
||||
.dev = {
|
||||
.platform_data = &bfin_gpio_keys_data,
|
||||
},
|
||||
};
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
|
||||
|
||||
static struct bfin_sd_host bfin_sdh_data = {
|
||||
.dma_chan = CH_RSI,
|
||||
.irq_int0 = IRQ_RSI_INT0,
|
||||
.pin_req = {P_RSI_DATA0, P_RSI_DATA1, P_RSI_DATA2, P_RSI_DATA3, P_RSI_CMD, P_RSI_CLK, 0},
|
||||
};
|
||||
|
||||
static struct platform_device bf51x_sdh_device = {
|
||||
.name = "bfin-sdh",
|
||||
.id = 0,
|
||||
.dev = {
|
||||
.platform_data = &bfin_sdh_data,
|
||||
},
|
||||
};
|
||||
#endif
|
||||
|
||||
static const unsigned int cclk_vlev_datasheet[] =
|
||||
{
|
||||
VRPAIR(VLEV_100, 400000000),
|
||||
VRPAIR(VLEV_105, 426000000),
|
||||
VRPAIR(VLEV_110, 500000000),
|
||||
VRPAIR(VLEV_115, 533000000),
|
||||
VRPAIR(VLEV_120, 600000000),
|
||||
};
|
||||
|
||||
static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
|
||||
.tuple_tab = cclk_vlev_datasheet,
|
||||
.tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
|
||||
.vr_settling_time = 25 /* us */,
|
||||
};
|
||||
|
||||
static struct platform_device bfin_dpmc = {
|
||||
.name = "bfin dpmc",
|
||||
.dev = {
|
||||
.platform_data = &bfin_dmpc_vreg_data,
|
||||
},
|
||||
};
|
||||
|
||||
static struct platform_device *tcm_devices[] __initdata = {
|
||||
|
||||
&bfin_dpmc,
|
||||
|
||||
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
|
||||
&rtc_device,
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
|
||||
&bfin_mii_bus,
|
||||
&bfin_mac_device,
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
|
||||
&bfin_spi0_device,
|
||||
&bfin_spi1_device,
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
|
||||
#ifdef CONFIG_SERIAL_BFIN_UART0
|
||||
&bfin_uart0_device,
|
||||
#endif
|
||||
#ifdef CONFIG_SERIAL_BFIN_UART1
|
||||
&bfin_uart1_device,
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
|
||||
#ifdef CONFIG_BFIN_SIR0
|
||||
&bfin_sir0_device,
|
||||
#endif
|
||||
#ifdef CONFIG_BFIN_SIR1
|
||||
&bfin_sir1_device,
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
|
||||
&i2c_bfin_twi_device,
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
|
||||
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
|
||||
&bfin_sport0_uart_device,
|
||||
#endif
|
||||
#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
|
||||
&bfin_sport1_uart_device,
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
|
||||
&bfin_device_gpiokeys,
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
|
||||
&bf51x_sdh_device,
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
|
||||
&tcm_flash_device,
|
||||
#endif
|
||||
};
|
||||
|
||||
static int __init tcm_init(void)
|
||||
{
|
||||
printk(KERN_INFO "%s(): registering device resources\n", __func__);
|
||||
i2c_register_board_info(0, bfin_i2c_board_info,
|
||||
ARRAY_SIZE(bfin_i2c_board_info));
|
||||
platform_add_devices(tcm_devices, ARRAY_SIZE(tcm_devices));
|
||||
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
|
||||
return 0;
|
||||
}
|
||||
|
||||
arch_initcall(tcm_init);
|
||||
|
||||
static struct platform_device *tcm_early_devices[] __initdata = {
|
||||
#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
|
||||
#ifdef CONFIG_SERIAL_BFIN_UART0
|
||||
&bfin_uart0_device,
|
||||
#endif
|
||||
#ifdef CONFIG_SERIAL_BFIN_UART1
|
||||
&bfin_uart1_device,
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
|
||||
#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
|
||||
&bfin_sport0_uart_device,
|
||||
#endif
|
||||
#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
|
||||
&bfin_sport1_uart_device,
|
||||
#endif
|
||||
#endif
|
||||
};
|
||||
|
||||
void __init native_machine_early_platform_add_devices(void)
|
||||
{
|
||||
printk(KERN_INFO "register early platform devices\n");
|
||||
early_platform_add_devices(tcm_early_devices,
|
||||
ARRAY_SIZE(tcm_early_devices));
|
||||
}
|
||||
|
||||
void native_machine_restart(char *cmd)
|
||||
{
|
||||
/* workaround reboot hang when booting from SPI */
|
||||
if ((bfin_read_SYSCR() & 0x7) == 0x3)
|
||||
bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
|
||||
}
|
||||
|
||||
void bfin_get_ether_addr(char *addr)
|
||||
{
|
||||
random_ether_addr(addr);
|
||||
printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
|
||||
}
|
||||
EXPORT_SYMBOL(bfin_get_ether_addr);
|
||||
Загрузка…
Ссылка в новой задаче