[ARM] pxa: add document on the MFP design and how to use it
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This commit is contained in:
Eric Miao
Родитель
28a623855f
Коммит
5bfb4093be
|
|
@ -0,0 +1,286 @@
|
|||
MFP Configuration for PXA2xx/PXA3xx Processors
|
||||
|
||||
Eric Miao <eric.miao@marvell.com>
|
||||
|
||||
MFP stands for Multi-Function Pin, which is the pin-mux logic on PXA3xx and
|
||||
later PXA series processors. This document describes the existing MFP API,
|
||||
and how board/platform driver authors could make use of it.
|
||||
|
||||
Basic Concept
|
||||
===============
|
||||
|
||||
Unlike the GPIO alternate function settings on PXA25x and PXA27x, a new MFP
|
||||
mechanism is introduced from PXA3xx to completely move the pin-mux functions
|
||||
out of the GPIO controller. In addition to pin-mux configurations, the MFP
|
||||
also controls the low power state, driving strength, pull-up/down and event
|
||||
detection of each pin. Below is a diagram of internal connections between
|
||||
the MFP logic and the remaining SoC peripherals:
|
||||
|
||||
+--------+
|
||||
| |--(GPIO19)--+
|
||||
| GPIO | |
|
||||
| |--(GPIO...) |
|
||||
+--------+ |
|
||||
| +---------+
|
||||
+--------+ +------>| |
|
||||
| PWM2 |--(PWM_OUT)-------->| MFP |
|
||||
+--------+ +------>| |-------> to external PAD
|
||||
| +---->| |
|
||||
+--------+ | | +-->| |
|
||||
| SSP2 |---(TXD)----+ | | +---------+
|
||||
+--------+ | |
|
||||
| |
|
||||
+--------+ | |
|
||||
| Keypad |--(MKOUT4)----+ |
|
||||
+--------+ |
|
||||
|
|
||||
+--------+ |
|
||||
| UART2 |---(TXD)--------+
|
||||
+--------+
|
||||
|
||||
NOTE: the external pad is named as MFP_PIN_GPIO19, it doesn't necessarily
|
||||
mean it's dedicated for GPIO19, only as a hint that internally this pin
|
||||
can be routed from GPIO19 of the GPIO controller.
|
||||
|
||||
To better understand the change from PXA25x/PXA27x GPIO alternate function
|
||||
to this new MFP mechanism, here are several key points:
|
||||
|
||||
1. GPIO controller on PXA3xx is now a dedicated controller, same as other
|
||||
internal controllers like PWM, SSP and UART, with 128 internal signals
|
||||
which can be routed to external through one or more MFPs (e.g. GPIO<0>
|
||||
can be routed through either MFP_PIN_GPIO0 as well as MFP_PIN_GPIO0_2,
|
||||
see arch/arm/mach-pxa/mach/include/mfp-pxa300.h)
|
||||
|
||||
2. Alternate function configuration is removed from this GPIO controller,
|
||||
the remaining functions are pure GPIO-specific, i.e.
|
||||
|
||||
- GPIO signal level control
|
||||
- GPIO direction control
|
||||
- GPIO level change detection
|
||||
|
||||
3. Low power state for each pin is now controlled by MFP, this means the
|
||||
PGSRx registers on PXA2xx are now useless on PXA3xx
|
||||
|
||||
4. Wakeup detection is now controlled by MFP, PWER does not control the
|
||||
wakeup from GPIO(s) any more, depending on the sleeping state, ADxER
|
||||
(as defined in pxa3xx-regs.h) controls the wakeup from MFP
|
||||
|
||||
NOTE: with such a clear separation of MFP and GPIO, by GPIO<xx> we normally
|
||||
mean it is a GPIO signal, and by MFP<xxx> or pin xxx, we mean a physical
|
||||
pad (or ball).
|
||||
|
||||
MFP API Usage
|
||||
===============
|
||||
|
||||
For board code writers, here are some guidelines:
|
||||
|
||||
1. include ONE of the following header files in your <board>.c:
|
||||
|
||||
- #include <mach/mfp-pxa25x.h>
|
||||
- #include <mach/mfp-pxa27x.h>
|
||||
- #include <mach/mfp-pxa300.h>
|
||||
- #include <mach/mfp-pxa320.h>
|
||||
- #include <mach/mfp-pxa930.h>
|
||||
|
||||
NOTE: only one file in your <board>.c, depending on the processors used,
|
||||
because pin configuration definitions may conflict in these file (i.e.
|
||||
same name, different meaning and settings on different processors). E.g.
|
||||
for zylonite platform, which support both PXA300/PXA310 and PXA320, two
|
||||
separate files are introduced: zylonite_pxa300.c and zylonite_pxa320.c
|
||||
(in addition to handle MFP configuration differences, they also handle
|
||||
the other differences between the two combinations).
|
||||
|
||||
NOTE: PXA300 and PXA310 are almost identical in pin configurations (with
|
||||
PXA310 supporting some additional ones), thus the difference is actually
|
||||
covered in a single mfp-pxa300.h.
|
||||
|
||||
2. prepare an array for the initial pin configurations, e.g.:
|
||||
|
||||
static unsigned long mainstone_pin_config[] __initdata = {
|
||||
/* Chip Select */
|
||||
GPIO15_nCS_1,
|
||||
|
||||
/* LCD - 16bpp Active TFT */
|
||||
GPIOxx_TFT_LCD_16BPP,
|
||||
GPIO16_PWM0_OUT, /* Backlight */
|
||||
|
||||
/* MMC */
|
||||
GPIO32_MMC_CLK,
|
||||
GPIO112_MMC_CMD,
|
||||
GPIO92_MMC_DAT_0,
|
||||
GPIO109_MMC_DAT_1,
|
||||
GPIO110_MMC_DAT_2,
|
||||
GPIO111_MMC_DAT_3,
|
||||
|
||||
...
|
||||
|
||||
/* GPIO */
|
||||
GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,
|
||||
};
|
||||
|
||||
a) once the pin configurations are passed to pxa{2xx,3xx}_mfp_config(),
|
||||
and written to the actual registers, they are useless and may discard,
|
||||
adding '__initdata' will help save some additional bytes here.
|
||||
|
||||
b) when there is only one possible pin configurations for a component,
|
||||
some simplified definitions can be used, e.g. GPIOxx_TFT_LCD_16BPP on
|
||||
PXA25x and PXA27x processors
|
||||
|
||||
c) if by board design, a pin can be configured to wake up the system
|
||||
from low power state, it can be 'OR'ed with any of:
|
||||
|
||||
WAKEUP_ON_EDGE_BOTH
|
||||
WAKEUP_ON_EDGE_RISE
|
||||
WAKEUP_ON_EDGE_FALL
|
||||
WAKEUP_ON_LEVEL_HIGH - specifically for enabling of keypad GPIOs,
|
||||
|
||||
to indicate that this pin has the capability of wake-up the system,
|
||||
and on which edge(s). This, however, doesn't necessarily mean the
|
||||
pin _will_ wakeup the system, it will only when set_irq_wake() is
|
||||
invoked with the corresponding GPIO IRQ (GPIO_IRQ(xx) or gpio_to_irq())
|
||||
and eventually calls gpio_set_wake() for the actual register setting.
|
||||
|
||||
d) although PXA3xx MFP supports edge detection on each pin, the
|
||||
internal logic will only wakeup the system when those specific bits
|
||||
in ADxER registers are set, which can be well mapped to the
|
||||
corresponding peripheral, thus set_irq_wake() can be called with
|
||||
the peripheral IRQ to enable the wakeup.
|
||||
|
||||
|
||||
MFP on PXA3xx
|
||||
===============
|
||||
|
||||
Every external I/O pad on PXA3xx (excluding those for special purpose) has
|
||||
one MFP logic associated, and is controlled by one MFP register (MFPR).
|
||||
|
||||
The MFPR has the following bit definitions (for PXA300/PXA310/PXA320):
|
||||
|
||||
31 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
|
||||
+-------------------------+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
|
||||
| RESERVED |PS|PU|PD| DRIVE |SS|SD|SO|EC|EF|ER|--| AF_SEL |
|
||||
+-------------------------+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
|
||||
|
||||
Bit 3: RESERVED
|
||||
Bit 4: EDGE_RISE_EN - enable detection of rising edge on this pin
|
||||
Bit 5: EDGE_FALL_EN - enable detection of falling edge on this pin
|
||||
Bit 6: EDGE_CLEAR - disable edge detection on this pin
|
||||
Bit 7: SLEEP_OE_N - enable outputs during low power modes
|
||||
Bit 8: SLEEP_DATA - output data on the pin during low power modes
|
||||
Bit 9: SLEEP_SEL - selection control for low power modes signals
|
||||
Bit 13: PULLDOWN_EN - enable the internal pull-down resistor on this pin
|
||||
Bit 14: PULLUP_EN - enable the internal pull-up resistor on this pin
|
||||
Bit 15: PULL_SEL - pull state controlled by selected alternate function
|
||||
(0) or by PULL{UP,DOWN}_EN bits (1)
|
||||
|
||||
Bit 0 - 2: AF_SEL - alternate function selection, 8 possibilities, from 0-7
|
||||
Bit 10-12: DRIVE - drive strength and slew rate
|
||||
0b000 - fast 1mA
|
||||
0b001 - fast 2mA
|
||||
0b002 - fast 3mA
|
||||
0b003 - fast 4mA
|
||||
0b004 - slow 6mA
|
||||
0b005 - fast 6mA
|
||||
0b006 - slow 10mA
|
||||
0b007 - fast 10mA
|
||||
|
||||
MFP Design for PXA2xx/PXA3xx
|
||||
==============================
|
||||
|
||||
Due to the difference of pin-mux handling between PXA2xx and PXA3xx, a unified
|
||||
MFP API is introduced to cover both series of processors.
|
||||
|
||||
The basic idea of this design is to introduce definitions for all possible pin
|
||||
configurations, these definitions are processor and platform independent, and
|
||||
the actual API invoked to convert these definitions into register settings and
|
||||
make them effective there-after.
|
||||
|
||||
Files Involved
|
||||
--------------
|
||||
|
||||
- arch/arm/mach-pxa/include/mach/mfp.h
|
||||
|
||||
for
|
||||
1. Unified pin definitions - enum constants for all configurable pins
|
||||
2. processor-neutral bit definitions for a possible MFP configuration
|
||||
|
||||
- arch/arm/mach-pxa/include/mach/mfp-pxa3xx.h
|
||||
|
||||
for PXA3xx specific MFPR register bit definitions and PXA3xx common pin
|
||||
configurations
|
||||
|
||||
- arch/arm/mach-pxa/include/mach/mfp-pxa2xx.h
|
||||
|
||||
for PXA2xx specific definitions and PXA25x/PXA27x common pin configurations
|
||||
|
||||
- arch/arm/mach-pxa/include/mach/mfp-pxa25x.h
|
||||
arch/arm/mach-pxa/include/mach/mfp-pxa27x.h
|
||||
arch/arm/mach-pxa/include/mach/mfp-pxa300.h
|
||||
arch/arm/mach-pxa/include/mach/mfp-pxa320.h
|
||||
arch/arm/mach-pxa/include/mach/mfp-pxa930.h
|
||||
|
||||
for processor specific definitions
|
||||
|
||||
- arch/arm/mach-pxa/mfp-pxa3xx.c
|
||||
- arch/arm/mach-pxa/mfp-pxa2xx.c
|
||||
|
||||
for implementation of the pin configuration to take effect for the actual
|
||||
processor.
|
||||
|
||||
Pin Configuration
|
||||
-----------------
|
||||
|
||||
The following comments are copied from mfp.h (see the actual source code
|
||||
for most updated info)
|
||||
|
||||
/*
|
||||
* a possible MFP configuration is represented by a 32-bit integer
|
||||
*
|
||||
* bit 0.. 9 - MFP Pin Number (1024 Pins Maximum)
|
||||
* bit 10..12 - Alternate Function Selection
|
||||
* bit 13..15 - Drive Strength
|
||||
* bit 16..18 - Low Power Mode State
|
||||
* bit 19..20 - Low Power Mode Edge Detection
|
||||
* bit 21..22 - Run Mode Pull State
|
||||
*
|
||||
* to facilitate the definition, the following macros are provided
|
||||
*
|
||||
* MFP_CFG_DEFAULT - default MFP configuration value, with
|
||||
* alternate function = 0,
|
||||
* drive strength = fast 3mA (MFP_DS03X)
|
||||
* low power mode = default
|
||||
* edge detection = none
|
||||
*
|
||||
* MFP_CFG - default MFPR value with alternate function
|
||||
* MFP_CFG_DRV - default MFPR value with alternate function and
|
||||
* pin drive strength
|
||||
* MFP_CFG_LPM - default MFPR value with alternate function and
|
||||
* low power mode
|
||||
* MFP_CFG_X - default MFPR value with alternate function,
|
||||
* pin drive strength and low power mode
|
||||
*/
|
||||
|
||||
Examples of pin configurations are:
|
||||
|
||||
#define GPIO94_SSP3_RXD MFP_CFG_X(GPIO94, AF1, DS08X, FLOAT)
|
||||
|
||||
which reads GPIO94 can be configured as SSP3_RXD, with alternate function
|
||||
selection of 1, driving strength of 0b101, and a float state in low power
|
||||
modes.
|
||||
|
||||
NOTE: this is the default setting of this pin being configured as SSP3_RXD
|
||||
which can be modified a bit in board code, though it is not recommended to
|
||||
do so, simply because this default setting is usually carefully encoded,
|
||||
and is supposed to work in most cases.
|
||||
|
||||
Register Settings
|
||||
-----------------
|
||||
|
||||
Register settings on PXA3xx for a pin configuration is actually very
|
||||
straight-forward, most bits can be converted directly into MFPR value
|
||||
in a easier way. Two sets of MFPR values are calculated: the run-time
|
||||
ones and the low power mode ones, to allow different settings.
|
||||
|
||||
The conversion from a generic pin configuration to the actual register
|
||||
settings on PXA2xx is a bit complicated: many registers are involved,
|
||||
including GAFRx, GPDRx, PGSRx, PWER, PKWR, PFER and PRER. Please see
|
||||
mfp-pxa2xx.c for how the conversion is made.
|
||||
Загрузка…
Ссылка в новой задаче