arm64: dts: add support for Marvell cn9130-crb platform
The Marvell reference platform CN9130-CRB is a small form factor board in a metal case. The platform is based on CN9130 SoC with addition of 8 Gigabit ports SOHO Ethernet switch. The reference platform features the following: * Up to 4 CPU cores ARMv8 Cortex-A72 CPU * CPU core operating speed of up to 2.2GHz * DDR4 DIMM – 8GB 64bit+ECC @ 2400Mhz. * 1x eMMC 8GB device * 1x uSD card 4 bits port on CP * 1x 128MB SPI NOR flash memory * 1x USB 3.0 Host port (Type A) * 1x SATA Gen3 via M.2 * 1x USB 3.0 via M.2 * 1x SIM card slot * 1x 1G Ethernet port via RGMII * 1x 10G switch port over SFP+ connector * 8x 1G ports through 88E6393X switch via XFI * 1x 2.5G/1G/100M/10M port via HS_SGMII * 1x PCI Express (PCIe)x1 Gen 3.0 * 1x PCI Express (PCIe)x4 Gen 3.0 via NVMe M.2 * JTAG port The CRB board uses MCP23017 i2c pin controller that drives the onboard eMMC abd USB 3,0 port power lines. The following configuration should be enabled for this controller support: CONFIG_PINCTRL_MCP23S08=y The plaform supports two HW configurations - "A" and "B" CN9130-CRB-A * AP-MPP configuration: SDIO, UART * CP0 Serdes configuration: * Lane0-3: NVMe (PCIe x4) * Lane4: XFI * Lane5: HS_SGMII 2. CN9130-CRB-B * AP-MPP configuration: SDIO, UART * CP0-MPP configuration: RGMII, SDIO, I2C0, I2C1, SMI, XSMI * CP0 Serdes configuration: * Lane0: PCIe x1 * Lane1: USB3_0 x1 * Lane2: SATA x1 * Lane3: USB3_1 x1 * Lane4: XFI * Lane5: HS_SGMII Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This commit is contained in:
Konstantin Porotchkin
Gregory CLEMENT
Родитель
f3200db5c6
Коммит
5c0ee54723
|
|
@ -21,3 +21,5 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb
|
||||||
dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db-B.dtb
|
dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db-B.dtb
|
||||||
dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
|
dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
|
||||||
dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
|
dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
|
||||||
|
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
|
||||||
|
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
|
||||||
|
|
|
||||||
|
|
@ -0,0 +1,38 @@
|
||||||
|
// SPDX-License-Identifier: GPL-2.0+
|
||||||
|
/*
|
||||||
|
* Copyright (C) 2020 Marvell International Ltd.
|
||||||
|
*/
|
||||||
|
|
||||||
|
#include "cn9130-crb.dtsi"
|
||||||
|
|
||||||
|
/ {
|
||||||
|
model = "Marvell Armada CN9130-CRB-A";
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_pcie0 {
|
||||||
|
status = "okay";
|
||||||
|
num-lanes = <4>;
|
||||||
|
num-viewport = <8>;
|
||||||
|
/* Generic PHY, providing serdes lanes */
|
||||||
|
phys = <&cp0_comphy0 0
|
||||||
|
&cp0_comphy1 0
|
||||||
|
&cp0_comphy2 0
|
||||||
|
&cp0_comphy3 0>;
|
||||||
|
iommu-map =
|
||||||
|
<0x0 &smmu 0x480 0x20>,
|
||||||
|
<0x100 &smmu 0x4a0 0x20>,
|
||||||
|
<0x200 &smmu 0x4c0 0x20>;
|
||||||
|
iommu-map-mask = <0x031f>;
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_usb3_0 {
|
||||||
|
status = "okay";
|
||||||
|
usb-phy = <&cp0_usb3_0_phy0>;
|
||||||
|
phy-names = "usb";
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_usb3_1 {
|
||||||
|
status = "okay";
|
||||||
|
usb-phy = <&cp0_usb3_0_phy1>;
|
||||||
|
phy-names = "usb";
|
||||||
|
};
|
||||||
|
|
@ -0,0 +1,46 @@
|
||||||
|
// SPDX-License-Identifier: GPL-2.0+
|
||||||
|
/*
|
||||||
|
* Copyright (C) 2020 Marvell International Ltd.
|
||||||
|
*/
|
||||||
|
|
||||||
|
#include "cn9130-crb.dtsi"
|
||||||
|
|
||||||
|
/ {
|
||||||
|
model = "Marvell Armada CN9130-CRB-B";
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_pcie0 {
|
||||||
|
status = "okay";
|
||||||
|
num-lanes = <1>;
|
||||||
|
num-viewport = <8>;
|
||||||
|
/* Generic PHY, providing serdes lanes */
|
||||||
|
phys = <&cp0_comphy0 0>;
|
||||||
|
iommu-map =
|
||||||
|
<0x0 &smmu 0x480 0x20>,
|
||||||
|
<0x100 &smmu 0x4a0 0x20>,
|
||||||
|
<0x200 &smmu 0x4c0 0x20>;
|
||||||
|
iommu-map-mask = <0x031f>;
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_sata0 {
|
||||||
|
status = "okay";
|
||||||
|
sata-port@0 {
|
||||||
|
status = "okay";
|
||||||
|
/* Generic PHY, providing serdes lanes */
|
||||||
|
phys = <&cp0_comphy2 0>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_usb3_0 {
|
||||||
|
status = "okay";
|
||||||
|
usb-phy = <&cp0_usb3_0_phy0>;
|
||||||
|
phy-names = "usb";
|
||||||
|
phys = <&cp0_comphy1 0>;
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_usb3_1 {
|
||||||
|
status = "okay";
|
||||||
|
usb-phy = <&cp0_usb3_0_phy1>;
|
||||||
|
phy-names = "usb";
|
||||||
|
phys = <&cp0_comphy3 1>;
|
||||||
|
};
|
||||||
|
|
@ -0,0 +1,222 @@
|
||||||
|
// SPDX-License-Identifier: GPL-2.0+
|
||||||
|
/*
|
||||||
|
* Copyright (C) 2020 Marvell International Ltd.
|
||||||
|
*/
|
||||||
|
|
||||||
|
#include "cn9130.dtsi" /* include SoC device tree */
|
||||||
|
|
||||||
|
#include <dt-bindings/gpio/gpio.h>
|
||||||
|
|
||||||
|
/ {
|
||||||
|
chosen {
|
||||||
|
stdout-path = "serial0:115200n8";
|
||||||
|
};
|
||||||
|
|
||||||
|
aliases {
|
||||||
|
i2c0 = &cp0_i2c0;
|
||||||
|
ethernet0 = &cp0_eth0;
|
||||||
|
ethernet1 = &cp0_eth1;
|
||||||
|
ethernet2 = &cp0_eth2;
|
||||||
|
};
|
||||||
|
|
||||||
|
memory@00000000 {
|
||||||
|
device_type = "memory";
|
||||||
|
reg = <0x0 0x0 0x0 0x80000000>;
|
||||||
|
};
|
||||||
|
|
||||||
|
ap0_reg_mmc_vccq: ap0_mmc_vccq@0 {
|
||||||
|
compatible = "regulator-gpio";
|
||||||
|
regulator-name = "ap0_mmc_vccq";
|
||||||
|
regulator-min-microvolt = <1800000>;
|
||||||
|
regulator-max-microvolt = <3300000>;
|
||||||
|
gpios = <&expander0 5 GPIO_ACTIVE_HIGH>;
|
||||||
|
states = <1800000 0x1
|
||||||
|
3300000 0x0>;
|
||||||
|
};
|
||||||
|
|
||||||
|
cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 {
|
||||||
|
compatible = "regulator-fixed";
|
||||||
|
regulator-name = "cp0-xhci1-vbus";
|
||||||
|
regulator-min-microvolt = <5000000>;
|
||||||
|
regulator-max-microvolt = <5000000>;
|
||||||
|
enable-active-high;
|
||||||
|
gpio = <&expander0 8 GPIO_ACTIVE_HIGH>;
|
||||||
|
};
|
||||||
|
|
||||||
|
cp0_usb3_0_phy0: cp0_usb3_phy0 {
|
||||||
|
compatible = "usb-nop-xceiv";
|
||||||
|
};
|
||||||
|
|
||||||
|
cp0_usb3_0_phy1: cp0_usb3_phy1 {
|
||||||
|
compatible = "usb-nop-xceiv";
|
||||||
|
vcc-supply = <&cp0_reg_usb3_vbus1>;
|
||||||
|
};
|
||||||
|
|
||||||
|
cp0_reg_sd_vccq: cp0_sd_vccq@0 {
|
||||||
|
compatible = "regulator-gpio";
|
||||||
|
regulator-name = "cp0_sd_vccq";
|
||||||
|
regulator-min-microvolt = <1800000>;
|
||||||
|
regulator-max-microvolt = <3300000>;
|
||||||
|
gpios = <&cp0_gpio2 18 GPIO_ACTIVE_HIGH>;
|
||||||
|
states = <1800000 0x1
|
||||||
|
3300000 0x0>;
|
||||||
|
};
|
||||||
|
|
||||||
|
cp0_reg_sd_vcc: cp0_sd_vcc@0 {
|
||||||
|
compatible = "regulator-fixed";
|
||||||
|
regulator-name = "cp0_sd_vcc";
|
||||||
|
regulator-min-microvolt = <3300000>;
|
||||||
|
regulator-max-microvolt = <3300000>;
|
||||||
|
gpio = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>;
|
||||||
|
enable-active-high;
|
||||||
|
regulator-always-on;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&uart0 {
|
||||||
|
status = "okay";
|
||||||
|
};
|
||||||
|
|
||||||
|
/* on-board eMMC U6 */
|
||||||
|
&ap_sdhci0 {
|
||||||
|
pinctrl-names = "default";
|
||||||
|
bus-width = <8>;
|
||||||
|
status = "okay";
|
||||||
|
mmc-ddr-1_8v;
|
||||||
|
vqmmc-supply = <&ap0_reg_mmc_vccq>;
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_syscon0 {
|
||||||
|
cp0_pinctrl: pinctrl {
|
||||||
|
compatible = "marvell,cp115-standalone-pinctrl";
|
||||||
|
|
||||||
|
cp0_i2c0_pins: cp0-i2c-pins-0 {
|
||||||
|
marvell,pins = "mpp37", "mpp38";
|
||||||
|
marvell,function = "i2c0";
|
||||||
|
};
|
||||||
|
cp0_i2c1_pins: cp0-i2c-pins-1 {
|
||||||
|
marvell,pins = "mpp35", "mpp36";
|
||||||
|
marvell,function = "i2c1";
|
||||||
|
};
|
||||||
|
cp0_sdhci_cd_pins_crb: cp0-sdhci-cd-pins-crb {
|
||||||
|
marvell,pins = "mpp55";
|
||||||
|
marvell,function = "gpio";
|
||||||
|
};
|
||||||
|
cp0_sdhci_pins: cp0-sdhi-pins-0 {
|
||||||
|
marvell,pins = "mpp56", "mpp57", "mpp58",
|
||||||
|
"mpp59", "mpp60", "mpp61";
|
||||||
|
marvell,function = "sdio";
|
||||||
|
};
|
||||||
|
cp0_spi0_pins: cp0-spi-pins-0 {
|
||||||
|
marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
|
||||||
|
marvell,function = "spi1";
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_i2c0 {
|
||||||
|
pinctrl-names = "default";
|
||||||
|
pinctrl-0 = <&cp0_i2c0_pins>;
|
||||||
|
status = "okay";
|
||||||
|
clock-frequency = <100000>;
|
||||||
|
expander0: mcp23x17@20 {
|
||||||
|
compatible = "microchip,mcp23017";
|
||||||
|
gpio-controller;
|
||||||
|
#gpio-cells = <2>;
|
||||||
|
reg = <0x20>;
|
||||||
|
status = "okay";
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_i2c1 {
|
||||||
|
pinctrl-names = "default";
|
||||||
|
pinctrl-0 = <&cp0_i2c1_pins>;
|
||||||
|
clock-frequency = <100000>;
|
||||||
|
status = "okay";
|
||||||
|
};
|
||||||
|
|
||||||
|
|
||||||
|
&cp0_sdhci0 {
|
||||||
|
pinctrl-names = "default";
|
||||||
|
pinctrl-0 = <&cp0_sdhci_pins
|
||||||
|
&cp0_sdhci_cd_pins_crb>;
|
||||||
|
bus-width = <4>;
|
||||||
|
cd-gpios = <&cp0_gpio2 23 GPIO_ACTIVE_HIGH>;
|
||||||
|
vqmmc-supply = <&cp0_reg_sd_vccq>;
|
||||||
|
vmmc-supply = <&cp0_reg_sd_vcc>;
|
||||||
|
status = "okay";
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_spi1 {
|
||||||
|
pinctrl-names = "default";
|
||||||
|
pinctrl-0 = <&cp0_spi0_pins>;
|
||||||
|
reg = <0x700680 0x50>, /* control */
|
||||||
|
<0x2000000 0x1000000>; /* CS0 */
|
||||||
|
status = "okay";
|
||||||
|
|
||||||
|
spi-flash@0 {
|
||||||
|
#address-cells = <0x1>;
|
||||||
|
#size-cells = <0x1>;
|
||||||
|
compatible = "jedec,spi-nor";
|
||||||
|
reg = <0x0>;
|
||||||
|
/* On-board MUX does not allow higher frequencies */
|
||||||
|
spi-max-frequency = <40000000>;
|
||||||
|
|
||||||
|
partitions {
|
||||||
|
compatible = "fixed-partitions";
|
||||||
|
#address-cells = <1>;
|
||||||
|
#size-cells = <1>;
|
||||||
|
|
||||||
|
partition@0 {
|
||||||
|
label = "U-Boot";
|
||||||
|
reg = <0x0 0x200000>;
|
||||||
|
};
|
||||||
|
|
||||||
|
partition@400000 {
|
||||||
|
label = "Filesystem";
|
||||||
|
reg = <0x200000 0xe00000>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_mdio {
|
||||||
|
status = "okay";
|
||||||
|
phy0: ethernet-phy@0 {
|
||||||
|
reg = <0>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_xmdio {
|
||||||
|
status = "okay";
|
||||||
|
nbaset_phy0: ethernet-phy@0 {
|
||||||
|
compatible = "ethernet-phy-ieee802.3-c45";
|
||||||
|
reg = <0>;
|
||||||
|
};
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_ethernet {
|
||||||
|
status = "okay";
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_eth0 {
|
||||||
|
/* This port is connected to 88E6393X switch */
|
||||||
|
status = "okay";
|
||||||
|
phy-mode = "10gbase-kr";
|
||||||
|
managed = "in-band-status";
|
||||||
|
phys = <&cp0_comphy4 0>;
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_eth1 {
|
||||||
|
status = "okay";
|
||||||
|
phy = <&phy0>;
|
||||||
|
phy-mode = "rgmii-id";
|
||||||
|
};
|
||||||
|
|
||||||
|
&cp0_eth2 {
|
||||||
|
/* This port uses "2500base-t" phy-mode */
|
||||||
|
status = "disabled";
|
||||||
|
phy = <&nbaset_phy0>;
|
||||||
|
phys = <&cp0_comphy5 2>;
|
||||||
|
};
|
||||||
|
|
||||||
Загрузка…
Ссылка в новой задаче