Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 6524/1: GIC irq desciptor bug fix
  ARM: 6523/1: iop: ensure sched_clock() is notrace
  ARM: 6456/1: Fix for building DEBUG with sa11xx_base.c as a module.
  ARM: 6519/1: kuser: Fix incorrect cmpxchg syscall in kuser helpers
  ARM: 6505/1: kprobes: Don't HAVE_KPROBES when CONFIG_THUMB2_KERNEL is selected
  ARM: 6508/1: vexpress: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
  ARM: 6507/1: RealView: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
  ARM: 6504/1: Thumb-2: Fix long-distance conditional branches in head.S for Thumb-2.
  ARM: 6503/1: Thumb-2: Restore sensible zImage header layout for CONFIG_THUMB2_KERNEL
  ARM: 6502/1: Thumb-2: Fix CONFIG_THUMB2_KERNEL breakage in compressed/head.S
  ARM: 6501/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in mm/proc-v7.S
  ARM: 6500/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in kernel/head.S
  ARM: 6499/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in bootp/init.S
  ARM: 6498/1: vfp: Correct data alignment for CONFIG_THUMB2_KERNEL
  ARM: 6497/1: kexec: Correct data alignment for CONFIG_THUMB2_KERNEL
  ARM: 6496/1: GIC: Do not try to register more then NR_IRQS interrupts
  ARM: cns3xxx: Fix build with CONFIG_PCI=y

arch/arm/Kconfig

@@ -9,7 +9,7 @@ config ARM
 	select GENERIC_ATOMIC64 if (!CPU_32v6K || !AEABI)
 	select HAVE_OPROFILE if (HAVE_PERF_EVENTS)
 	select HAVE_ARCH_KGDB
-	select HAVE_KPROBES if (!XIP_KERNEL)
+	select HAVE_KPROBES if (!XIP_KERNEL && !THUMB2_KERNEL)
 	select HAVE_KRETPROBES if (HAVE_KPROBES)
 	select HAVE_FUNCTION_TRACER if (!XIP_KERNEL)
 	select HAVE_FTRACE_MCOUNT_RECORD if (!XIP_KERNEL)

arch/arm/boot/Makefile

@@ -70,12 +70,7 @@ else
 $(obj)/uImage: LOADADDR=$(ZRELADDR)
 endif
 
-ifeq ($(CONFIG_THUMB2_KERNEL),y)
-# Set bit 0 to 1 so that "mov pc, rx" switches to Thumb-2 mode
-$(obj)/uImage: STARTADDR=$(shell echo $(LOADADDR) | sed -e "s/.$$/1/")
-else
 $(obj)/uImage: STARTADDR=$(LOADADDR)
-endif
 
 $(obj)/uImage:	$(obj)/zImage FORCE
 	$(call if_changed,uimage)

arch/arm/boot/bootp/init.S

@@ -73,6 +73,8 @@ move:		ldmia	r4!, {r7 - r10}		@ move 32-bytes at a time
 
 		.size	_start, . - _start
 
+		.align
+
 		.type	data,#object
 data:		.word	initrd_start		@ source initrd address
 		.word	initrd_phys		@ destination initrd address

arch/arm/boot/compressed/head.S

@@ -125,9 +125,13 @@ wait:		mrc	p14, 0, pc, c0, c1, 0
  * sort out different calling conventions
  */
 		.align
+		.arm				@ Always enter in ARM state
 start:
 		.type	start,#function
-		.rept	8
+ THUMB(		adr	r12, BSYM(1f)	)
+ THUMB(		bx	r12		)
+ THUMB(		.rept	6		)
+ ARM(		.rept	8		)
 		mov	r0, r0
 		.endr
 
@@ -135,6 +139,7 @@ start:
 		.word	0x016f2818		@ Magic numbers to help the loader
 		.word	start			@ absolute load/run zImage address
 		.word	_edata			@ zImage end address
+ THUMB(		.thumb			)
 1:		mov	r7, r1			@ save architecture ID
 		mov	r8, r2			@ save atags pointer
 
@@ -174,7 +179,8 @@ not_angel:
 		ldr	sp, [r0, #28]
 #ifdef CONFIG_AUTO_ZRELADDR
 		@ determine final kernel image address
-		and	r4, pc, #0xf8000000
+		mov	r4, pc
+		and	r4, r4, #0xf8000000
 		add	r4, r4, #TEXT_OFFSET
 #else
 		ldr	r4, =zreladdr
@@ -445,7 +451,8 @@ __setup_mmu:	sub	r3, r4, #16384		@ Page directory size
  */
 		mov	r1, #0x1e
 		orr	r1, r1, #3 << 10
-		mov	r2, pc, lsr #20
+		mov	r2, pc
+		mov	r2, r2, lsr #20
 		orr	r1, r1, r2, lsl #20
 		add	r0, r3, r2, lsl #2
 		str	r1, [r0], #4

arch/arm/common/gic.c

@@ -146,9 +146,15 @@ static int gic_set_cpu(unsigned int irq, const struct cpumask *mask_val)
 	unsigned int shift = (irq % 4) * 8;
 	unsigned int cpu = cpumask_first(mask_val);
 	u32 val;
+	struct irq_desc *desc;
 
 	spin_lock(&irq_controller_lock);
-	irq_desc[irq].node = cpu;
+	desc = irq_to_desc(irq);
+	if (desc == NULL) {
+		spin_unlock(&irq_controller_lock);
+		return -EINVAL;
+	}
+	desc->node = cpu;
 	val = readl(reg) & ~(0xff << shift);
 	val |= 1 << (cpu + shift);
 	writel(val, reg);
@@ -210,7 +216,7 @@ void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq)
 void __init gic_dist_init(unsigned int gic_nr, void __iomem *base,
 			  unsigned int irq_start)
 {
-	unsigned int max_irq, i;
+	unsigned int gic_irqs, irq_limit, i;
 	u32 cpumask = 1 << smp_processor_id();
 
 	if (gic_nr >= MAX_GIC_NR)
@@ -226,47 +232,49 @@ void __init gic_dist_init(unsigned int gic_nr, void __iomem *base,
 
 	/*
 	 * Find out how many interrupts are supported.
-	 */
-	max_irq = readl(base + GIC_DIST_CTR) & 0x1f;
-	max_irq = (max_irq + 1) * 32;
-
-	/*
 	 * The GIC only supports up to 1020 interrupt sources.
-	 * Limit this to either the architected maximum, or the
-	 * platform maximum.
 	 */
-	if (max_irq > max(1020, NR_IRQS))
+	gic_irqs = readl(base + GIC_DIST_CTR) & 0x1f;
-		max_irq = max(1020, NR_IRQS);
+	gic_irqs = (gic_irqs + 1) * 32;
+	if (gic_irqs > 1020)
+		gic_irqs = 1020;
 
 	/*
 	 * Set all global interrupts to be level triggered, active low.
 	 */
-	for (i = 32; i < max_irq; i += 16)
+	for (i = 32; i < gic_irqs; i += 16)
 		writel(0, base + GIC_DIST_CONFIG + i * 4 / 16);
 
 	/*
 	 * Set all global interrupts to this CPU only.
 	 */
-	for (i = 32; i < max_irq; i += 4)
+	for (i = 32; i < gic_irqs; i += 4)
 		writel(cpumask, base + GIC_DIST_TARGET + i * 4 / 4);
 
 	/*
 	 * Set priority on all global interrupts.
 	 */
-	for (i = 32; i < max_irq; i += 4)
+	for (i = 32; i < gic_irqs; i += 4)
 		writel(0xa0a0a0a0, base + GIC_DIST_PRI + i * 4 / 4);
 
 	/*
 	 * Disable all interrupts.  Leave the PPI and SGIs alone
 	 * as these enables are banked registers.
 	 */
-	for (i = 32; i < max_irq; i += 32)
+	for (i = 32; i < gic_irqs; i += 32)
 		writel(0xffffffff, base + GIC_DIST_ENABLE_CLEAR + i * 4 / 32);
 
+	/*
+	 * Limit number of interrupts registered to the platform maximum
+	 */
+	irq_limit = gic_data[gic_nr].irq_offset + gic_irqs;
+	if (WARN_ON(irq_limit > NR_IRQS))
+		irq_limit = NR_IRQS;
+
 	/*
 	 * Setup the Linux IRQ subsystem.
 	 */
-	for (i = irq_start; i < gic_data[gic_nr].irq_offset + max_irq; i++) {
+	for (i = irq_start; i < irq_limit; i++) {
 		set_irq_chip(i, &gic_chip);
 		set_irq_chip_data(i, &gic_data[gic_nr]);
 		set_irq_handler(i, handle_level_irq);

arch/arm/kernel/entry-armv.S

@@ -911,7 +911,7 @@ __kuser_cmpxchg:				@ 0xffff0fc0
 	 * A special ghost syscall is used for that (see traps.c).
 	 */
 	stmfd	sp!, {r7, lr}
-	ldr	r7, =1f			@ it's 20 bits
+	ldr	r7, 1f			@ it's 20 bits
 	swi	__ARM_NR_cmpxchg
 	ldmfd	sp!, {r7, pc}
 1:	.word	__ARM_NR_cmpxchg

arch/arm/kernel/head.S

@@ -85,9 +85,11 @@ ENTRY(stext)
 	mrc	p15, 0, r9, c0, c0		@ get processor id
 	bl	__lookup_processor_type		@ r5=procinfo r9=cpuid
 	movs	r10, r5				@ invalid processor (r5=0)?
+ THUMB( it	eq )		@ force fixup-able long branch encoding
 	beq	__error_p			@ yes, error 'p'
 	bl	__lookup_machine_type		@ r5=machinfo
 	movs	r8, r5				@ invalid machine (r5=0)?
+ THUMB( it	eq )		@ force fixup-able long branch encoding
 	beq	__error_a			@ yes, error 'a'
 	bl	__vet_atags
 #ifdef CONFIG_SMP_ON_UP
@@ -262,6 +264,7 @@ __create_page_tables:
 	mov	pc, lr
 ENDPROC(__create_page_tables)
 	.ltorg
+	.align
 __enable_mmu_loc:
 	.long	.
 	.long	__enable_mmu
@@ -282,6 +285,7 @@ ENTRY(secondary_startup)
 	bl	__lookup_processor_type
 	movs	r10, r5				@ invalid processor?
 	moveq	r0, #'p'			@ yes, error 'p'
+ THUMB( it	eq )		@ force fixup-able long branch encoding
 	beq	__error_p
 
 	/*
@@ -308,6 +312,8 @@ ENTRY(__secondary_switched)
 	b	secondary_start_kernel
 ENDPROC(__secondary_switched)
 
+	.align
+
 	.type	__secondary_data, %object
 __secondary_data:
 	.long	.
@@ -413,6 +419,7 @@ __fixup_smp_on_up:
 	mov	pc, lr
 ENDPROC(__fixup_smp)
 
+	.align
 1:	.word	.
 	.word	__smpalt_begin
 	.word	__smpalt_end

arch/arm/kernel/relocate_kernel.S

@@ -59,6 +59,8 @@ relocate_new_kernel:
 	ldr r2,kexec_boot_atags
 	mov pc,lr
 
+	.align
+
 	.globl kexec_start_address
 kexec_start_address:
 	.long	0x0

arch/arm/mach-cns3xxx/pcie.c

@@ -369,7 +369,7 @@ static int __init cns3xxx_pcie_init(void)
 {
 	int i;
 
-	hook_fault_code(16 + 6, cns3xxx_pcie_abort_handler, SIGBUS,
+	hook_fault_code(16 + 6, cns3xxx_pcie_abort_handler, SIGBUS, 0,
 			"imprecise external abort");
 
 	for (i = 0; i < ARRAY_SIZE(cns3xxx_pcie); i++) {

arch/arm/mach-realview/headsmp.S

@@ -35,5 +35,6 @@ pen:	ldr	r7, [r6]
 	 */
 	b	secondary_startup
 
+	.align
 1:	.long	.
 	.long	pen_release

arch/arm/mach-vexpress/headsmp.S

@@ -35,5 +35,6 @@ pen:	ldr	r7, [r6]
 	 */
 	b	secondary_startup
 
+	.align
 1:	.long	.
 	.long	pen_release

arch/arm/mm/proc-v7.S

@@ -381,7 +381,7 @@ __v7_ca9mp_proc_info:
 		PMD_SECT_XN | \
 		PMD_SECT_AP_WRITE | \
 		PMD_SECT_AP_READ
-	b	__v7_ca9mp_setup
+	W(b)	__v7_ca9mp_setup
 	.long	cpu_arch_name
 	.long	cpu_elf_name
 	.long	HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP|HWCAP_TLS
@@ -413,7 +413,7 @@ __v7_proc_info:
 		PMD_SECT_XN | \
 		PMD_SECT_AP_WRITE | \
 		PMD_SECT_AP_READ
-	b	__v7_setup
+	W(b)	__v7_setup
 	.long	cpu_arch_name
 	.long	cpu_elf_name
 	.long	HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP|HWCAP_TLS

arch/arm/plat-iop/time.c

@@ -18,6 +18,7 @@
 #include <linux/time.h>
 #include <linux/init.h>
 #include <linux/timex.h>
+#include <linux/sched.h>
 #include <linux/io.h>
 #include <linux/clocksource.h>
 #include <linux/clockchips.h>
@@ -36,7 +37,7 @@
 /*
  * IOP clocksource (free-running timer 1).
  */
-static cycle_t iop_clocksource_read(struct clocksource *unused)
+static cycle_t notrace iop_clocksource_read(struct clocksource *unused)
 {
 	return 0xffffffffu - read_tcr1();
 }

arch/arm/vfp/vfphw.S

@@ -206,6 +206,7 @@ ENTRY(vfp_save_state)
 	mov	pc, lr
 ENDPROC(vfp_save_state)
 
+	.align
 last_VFP_context_address:
 	.word	last_VFP_context
 

drivers/pcmcia/soc_common.c

@@ -70,6 +70,7 @@ void soc_pcmcia_debug(struct soc_pcmcia_socket *skt, const char *func,
 		va_end(args);
 	}
 }
+EXPORT_SYMBOL(soc_pcmcia_debug);
 
 #endif