diff --git a/Documentation/leds-lp3944.txt b/Documentation/leds-lp3944.txt new file mode 100644 index 000000000000..c6eda18b15ef --- /dev/null +++ b/Documentation/leds-lp3944.txt @@ -0,0 +1,50 @@ +Kernel driver lp3944 +==================== + + * National Semiconductor LP3944 Fun-light Chip + Prefix: 'lp3944' + Addresses scanned: None (see the Notes section below) + Datasheet: Publicly available at the National Semiconductor website + http://www.national.com/pf/LP/LP3944.html + +Authors: + Antonio Ospite + + +Description +----------- +The LP3944 is a helper chip that can drive up to 8 leds, with two programmable +DIM modes; it could even be used as a gpio expander but this driver assumes it +is used as a led controller. + +The DIM modes are used to set _blink_ patterns for leds, the pattern is +specified supplying two parameters: + - period: from 0s to 1.6s + - duty cycle: percentage of the period the led is on, from 0 to 100 + +Setting a led in DIM0 or DIM1 mode makes it blink according to the pattern. +See the datasheet for details. + +LP3944 can be found on Motorola A910 smartphone, where it drives the rgb +leds, the camera flash light and the lcds power. + + +Notes +----- +The chip is used mainly in embedded contexts, so this driver expects it is +registered using the i2c_board_info mechanism. + +To register the chip at address 0x60 on adapter 0, set the platform data +according to include/linux/leds-lp3944.h, set the i2c board info: + + static struct i2c_board_info __initdata a910_i2c_board_info[] = { + { + I2C_BOARD_INFO("lp3944", 0x60), + .platform_data = &a910_lp3944_leds, + }, + }; + +and register it in the platform init function + + i2c_register_board_info(0, a910_i2c_board_info, + ARRAY_SIZE(a910_i2c_board_info)); diff --git a/Documentation/powerpc/dts-bindings/gpio/led.txt b/Documentation/powerpc/dts-bindings/gpio/led.txt index 4fe14deedc0a..064db928c3c1 100644 --- a/Documentation/powerpc/dts-bindings/gpio/led.txt +++ b/Documentation/powerpc/dts-bindings/gpio/led.txt @@ -16,10 +16,17 @@ LED sub-node properties: string defining the trigger assigned to the LED. Current triggers are: "backlight" - LED will act as a back-light, controlled by the framebuffer system - "default-on" - LED will turn on + "default-on" - LED will turn on, but see "default-state" below "heartbeat" - LED "double" flashes at a load average based rate "ide-disk" - LED indicates disk activity "timer" - LED flashes at a fixed, configurable rate +- default-state: (optional) The initial state of the LED. Valid + values are "on", "off", and "keep". If the LED is already on or off + and the default-state property is set the to same value, then no + glitch should be produced where the LED momentarily turns off (or + on). The "keep" setting will keep the LED at whatever its current + state is, without producing a glitch. The default is off if this + property is not present. Examples: @@ -30,14 +37,22 @@ leds { gpios = <&mcu_pio 0 1>; /* Active low */ linux,default-trigger = "ide-disk"; }; + + fault { + gpios = <&mcu_pio 1 0>; + /* Keep LED on if BIOS detected hardware fault */ + default-state = "keep"; + }; }; run-control { compatible = "gpio-leds"; red { gpios = <&mpc8572 6 0>; + default-state = "off"; }; green { gpios = <&mpc8572 7 0>; + default-state = "on"; }; } diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig index 9b60b6b684d9..7c8e7122aaa9 100644 --- a/drivers/leds/Kconfig +++ b/drivers/leds/Kconfig @@ -75,6 +75,7 @@ config LEDS_ALIX2 depends on LEDS_CLASS && X86 && EXPERIMENTAL help This option enables support for the PCEngines ALIX.2 and ALIX.3 LEDs. + You have to set leds-alix2.force=1 for boards with Award BIOS. config LEDS_H1940 tristate "LED Support for iPAQ H1940 device" @@ -145,15 +146,16 @@ config LEDS_GPIO_OF of_platform devices. For instance, LEDs which are listed in a "dts" file. -config LEDS_LP5521 - tristate "LED Support for the LP5521 LEDs" +config LEDS_LP3944 + tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip" depends on LEDS_CLASS && I2C help - If you say 'Y' here you get support for the National Semiconductor - LP5521 LED driver used in n8x0 boards. + This option enables support for LEDs connected to the National + Semiconductor LP3944 Lighting Management Unit (LMU) also known as + Fun Light Chip. - This driver can be built as a module by choosing 'M'. The module - will be called leds-lp5521. + To compile this driver as a module, choose M here: the + module will be called leds-lp3944. config LEDS_CLEVO_MAIL tristate "Mail LED on Clevo notebook" diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile index 2d41c4dcf92f..e8cdcf77a4c3 100644 --- a/drivers/leds/Makefile +++ b/drivers/leds/Makefile @@ -20,6 +20,7 @@ obj-$(CONFIG_LEDS_COBALT_RAQ) += leds-cobalt-raq.o obj-$(CONFIG_LEDS_SUNFIRE) += leds-sunfire.o obj-$(CONFIG_LEDS_PCA9532) += leds-pca9532.o obj-$(CONFIG_LEDS_GPIO) += leds-gpio.o +obj-$(CONFIG_LEDS_LP3944) += leds-lp3944.o obj-$(CONFIG_LEDS_CLEVO_MAIL) += leds-clevo-mail.o obj-$(CONFIG_LEDS_HP6XX) += leds-hp6xx.o obj-$(CONFIG_LEDS_FSG) += leds-fsg.o diff --git a/drivers/leds/leds-alix2.c b/drivers/leds/leds-alix2.c index ddbd7730dfc8..731d4eef3425 100644 --- a/drivers/leds/leds-alix2.c +++ b/drivers/leds/leds-alix2.c @@ -14,7 +14,7 @@ static int force = 0; module_param(force, bool, 0444); -MODULE_PARM_DESC(force, "Assume system has ALIX.2 style LEDs"); +MODULE_PARM_DESC(force, "Assume system has ALIX.2/ALIX.3 style LEDs"); struct alix_led { struct led_classdev cdev; @@ -155,6 +155,11 @@ static int __init alix_led_init(void) goto out; } + /* enable output on GPIO for LED 1,2,3 */ + outl(1 << 6, 0x6104); + outl(1 << 9, 0x6184); + outl(1 << 11, 0x6184); + pdev = platform_device_register_simple(KBUILD_MODNAME, -1, NULL, 0); if (!IS_ERR(pdev)) { ret = platform_driver_probe(&alix_led_driver, alix_led_probe); diff --git a/drivers/leds/leds-bd2802.c b/drivers/leds/leds-bd2802.c index 4149ecb3a9b2..779d7f262c04 100644 --- a/drivers/leds/leds-bd2802.c +++ b/drivers/leds/leds-bd2802.c @@ -97,6 +97,10 @@ struct bd2802_led { enum led_ids led_id; enum led_colors color; enum led_bits state; + + /* General attributes of RGB LEDs */ + int wave_pattern; + int rgb_current; }; @@ -254,7 +258,7 @@ static void bd2802_set_on(struct bd2802_led *led, enum led_ids id, bd2802_reset_cancel(led); reg = bd2802_get_reg_addr(id, color, BD2802_REG_CURRENT1SETUP); - bd2802_write_byte(led->client, reg, BD2802_CURRENT_032); + bd2802_write_byte(led->client, reg, led->rgb_current); reg = bd2802_get_reg_addr(id, color, BD2802_REG_CURRENT2SETUP); bd2802_write_byte(led->client, reg, BD2802_CURRENT_000); reg = bd2802_get_reg_addr(id, color, BD2802_REG_WAVEPATTERN); @@ -275,9 +279,9 @@ static void bd2802_set_blink(struct bd2802_led *led, enum led_ids id, reg = bd2802_get_reg_addr(id, color, BD2802_REG_CURRENT1SETUP); bd2802_write_byte(led->client, reg, BD2802_CURRENT_000); reg = bd2802_get_reg_addr(id, color, BD2802_REG_CURRENT2SETUP); - bd2802_write_byte(led->client, reg, BD2802_CURRENT_032); + bd2802_write_byte(led->client, reg, led->rgb_current); reg = bd2802_get_reg_addr(id, color, BD2802_REG_WAVEPATTERN); - bd2802_write_byte(led->client, reg, BD2802_PATTERN_HALF); + bd2802_write_byte(led->client, reg, led->wave_pattern); bd2802_enable(led, id); bd2802_update_state(led, id, color, BD2802_BLINK); @@ -406,7 +410,7 @@ static void bd2802_enable_adv_conf(struct bd2802_led *led) ret = device_create_file(&led->client->dev, bd2802_addr_attributes[i]); if (ret) { - dev_err(&led->client->dev, "failed to sysfs file %s\n", + dev_err(&led->client->dev, "failed: sysfs file %s\n", bd2802_addr_attributes[i]->attr.name); goto failed_remove_files; } @@ -483,6 +487,52 @@ static struct device_attribute bd2802_adv_conf_attr = { .store = bd2802_store_adv_conf, }; +#define BD2802_CONTROL_ATTR(attr_name, name_str) \ +static ssize_t bd2802_show_##attr_name(struct device *dev, \ + struct device_attribute *attr, char *buf) \ +{ \ + struct bd2802_led *led = i2c_get_clientdata(to_i2c_client(dev));\ + ssize_t ret; \ + down_read(&led->rwsem); \ + ret = sprintf(buf, "0x%02x\n", led->attr_name); \ + up_read(&led->rwsem); \ + return ret; \ +} \ +static ssize_t bd2802_store_##attr_name(struct device *dev, \ + struct device_attribute *attr, const char *buf, size_t count) \ +{ \ + struct bd2802_led *led = i2c_get_clientdata(to_i2c_client(dev));\ + unsigned long val; \ + int ret; \ + if (!count) \ + return -EINVAL; \ + ret = strict_strtoul(buf, 16, &val); \ + if (ret) \ + return ret; \ + down_write(&led->rwsem); \ + led->attr_name = val; \ + up_write(&led->rwsem); \ + return count; \ +} \ +static struct device_attribute bd2802_##attr_name##_attr = { \ + .attr = { \ + .name = name_str, \ + .mode = 0644, \ + .owner = THIS_MODULE \ + }, \ + .show = bd2802_show_##attr_name, \ + .store = bd2802_store_##attr_name, \ +}; + +BD2802_CONTROL_ATTR(wave_pattern, "wave_pattern"); +BD2802_CONTROL_ATTR(rgb_current, "rgb_current"); + +static struct device_attribute *bd2802_attributes[] = { + &bd2802_adv_conf_attr, + &bd2802_wave_pattern_attr, + &bd2802_rgb_current_attr, +}; + static void bd2802_led_work(struct work_struct *work) { struct bd2802_led *led = container_of(work, struct bd2802_led, work); @@ -538,7 +588,6 @@ static int bd2802_register_led_classdev(struct bd2802_led *led) led->cdev_led1r.brightness = LED_OFF; led->cdev_led1r.brightness_set = bd2802_set_led1r_brightness; led->cdev_led1r.blink_set = bd2802_set_led1r_blink; - led->cdev_led1r.flags |= LED_CORE_SUSPENDRESUME; ret = led_classdev_register(&led->client->dev, &led->cdev_led1r); if (ret < 0) { @@ -551,7 +600,6 @@ static int bd2802_register_led_classdev(struct bd2802_led *led) led->cdev_led1g.brightness = LED_OFF; led->cdev_led1g.brightness_set = bd2802_set_led1g_brightness; led->cdev_led1g.blink_set = bd2802_set_led1g_blink; - led->cdev_led1g.flags |= LED_CORE_SUSPENDRESUME; ret = led_classdev_register(&led->client->dev, &led->cdev_led1g); if (ret < 0) { @@ -564,7 +612,6 @@ static int bd2802_register_led_classdev(struct bd2802_led *led) led->cdev_led1b.brightness = LED_OFF; led->cdev_led1b.brightness_set = bd2802_set_led1b_brightness; led->cdev_led1b.blink_set = bd2802_set_led1b_blink; - led->cdev_led1b.flags |= LED_CORE_SUSPENDRESUME; ret = led_classdev_register(&led->client->dev, &led->cdev_led1b); if (ret < 0) { @@ -577,7 +624,6 @@ static int bd2802_register_led_classdev(struct bd2802_led *led) led->cdev_led2r.brightness = LED_OFF; led->cdev_led2r.brightness_set = bd2802_set_led2r_brightness; led->cdev_led2r.blink_set = bd2802_set_led2r_blink; - led->cdev_led2r.flags |= LED_CORE_SUSPENDRESUME; ret = led_classdev_register(&led->client->dev, &led->cdev_led2r); if (ret < 0) { @@ -590,7 +636,6 @@ static int bd2802_register_led_classdev(struct bd2802_led *led) led->cdev_led2g.brightness = LED_OFF; led->cdev_led2g.brightness_set = bd2802_set_led2g_brightness; led->cdev_led2g.blink_set = bd2802_set_led2g_blink; - led->cdev_led2g.flags |= LED_CORE_SUSPENDRESUME; ret = led_classdev_register(&led->client->dev, &led->cdev_led2g); if (ret < 0) { @@ -640,7 +685,7 @@ static int __devinit bd2802_probe(struct i2c_client *client, { struct bd2802_led *led; struct bd2802_led_platform_data *pdata; - int ret; + int ret, i; led = kzalloc(sizeof(struct bd2802_led), GFP_KERNEL); if (!led) { @@ -670,13 +715,20 @@ static int __devinit bd2802_probe(struct i2c_client *client, /* To save the power, reset BD2802 after detecting */ gpio_set_value(led->pdata->reset_gpio, 0); + /* Default attributes */ + led->wave_pattern = BD2802_PATTERN_HALF; + led->rgb_current = BD2802_CURRENT_032; + init_rwsem(&led->rwsem); - ret = device_create_file(&client->dev, &bd2802_adv_conf_attr); - if (ret) { - dev_err(&client->dev, "failed to create sysfs file %s\n", - bd2802_adv_conf_attr.attr.name); - goto failed_free; + for (i = 0; i < ARRAY_SIZE(bd2802_attributes); i++) { + ret = device_create_file(&led->client->dev, + bd2802_attributes[i]); + if (ret) { + dev_err(&led->client->dev, "failed: sysfs file %s\n", + bd2802_attributes[i]->attr.name); + goto failed_unregister_dev_file; + } } ret = bd2802_register_led_classdev(led); @@ -686,7 +738,8 @@ static int __devinit bd2802_probe(struct i2c_client *client, return 0; failed_unregister_dev_file: - device_remove_file(&client->dev, &bd2802_adv_conf_attr); + for (i--; i >= 0; i--) + device_remove_file(&led->client->dev, bd2802_attributes[i]); failed_free: i2c_set_clientdata(client, NULL); kfree(led); @@ -697,12 +750,14 @@ failed_free: static int __exit bd2802_remove(struct i2c_client *client) { struct bd2802_led *led = i2c_get_clientdata(client); + int i; - bd2802_unregister_led_classdev(led); gpio_set_value(led->pdata->reset_gpio, 0); + bd2802_unregister_led_classdev(led); if (led->adf_on) bd2802_disable_adv_conf(led); - device_remove_file(&client->dev, &bd2802_adv_conf_attr); + for (i = 0; i < ARRAY_SIZE(bd2802_attributes); i++) + device_remove_file(&led->client->dev, bd2802_attributes[i]); i2c_set_clientdata(client, NULL); kfree(led); @@ -723,8 +778,7 @@ static int bd2802_resume(struct i2c_client *client) struct bd2802_led *led = i2c_get_clientdata(client); if (!bd2802_is_all_off(led) || led->adf_on) { - gpio_set_value(led->pdata->reset_gpio, 1); - udelay(100); + bd2802_reset_cancel(led); bd2802_restore_state(led); } @@ -762,4 +816,4 @@ module_exit(bd2802_exit); MODULE_AUTHOR("Kim Kyuwon "); MODULE_DESCRIPTION("BD2802 LED driver"); -MODULE_LICENSE("GPL"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/leds/leds-gpio.c b/drivers/leds/leds-gpio.c index d2109054de85..6b06638eb5b4 100644 --- a/drivers/leds/leds-gpio.c +++ b/drivers/leds/leds-gpio.c @@ -76,7 +76,7 @@ static int __devinit create_gpio_led(const struct gpio_led *template, struct gpio_led_data *led_dat, struct device *parent, int (*blink_set)(unsigned, unsigned long *, unsigned long *)) { - int ret; + int ret, state; /* skip leds that aren't available */ if (!gpio_is_valid(template->gpio)) { @@ -99,11 +99,15 @@ static int __devinit create_gpio_led(const struct gpio_led *template, led_dat->cdev.blink_set = gpio_blink_set; } led_dat->cdev.brightness_set = gpio_led_set; - led_dat->cdev.brightness = LED_OFF; + if (template->default_state == LEDS_GPIO_DEFSTATE_KEEP) + state = !!gpio_get_value(led_dat->gpio) ^ led_dat->active_low; + else + state = (template->default_state == LEDS_GPIO_DEFSTATE_ON); + led_dat->cdev.brightness = state ? LED_FULL : LED_OFF; if (!template->retain_state_suspended) led_dat->cdev.flags |= LED_CORE_SUSPENDRESUME; - ret = gpio_direction_output(led_dat->gpio, led_dat->active_low); + ret = gpio_direction_output(led_dat->gpio, led_dat->active_low ^ state); if (ret < 0) goto err; @@ -129,7 +133,7 @@ static void delete_gpio_led(struct gpio_led_data *led) } #ifdef CONFIG_LEDS_GPIO_PLATFORM -static int gpio_led_probe(struct platform_device *pdev) +static int __devinit gpio_led_probe(struct platform_device *pdev) { struct gpio_led_platform_data *pdata = pdev->dev.platform_data; struct gpio_led_data *leds_data; @@ -223,12 +227,22 @@ static int __devinit of_gpio_leds_probe(struct of_device *ofdev, memset(&led, 0, sizeof(led)); for_each_child_of_node(np, child) { enum of_gpio_flags flags; + const char *state; led.gpio = of_get_gpio_flags(child, 0, &flags); led.active_low = flags & OF_GPIO_ACTIVE_LOW; led.name = of_get_property(child, "label", NULL) ? : child->name; led.default_trigger = of_get_property(child, "linux,default-trigger", NULL); + state = of_get_property(child, "default-state", NULL); + if (state) { + if (!strcmp(state, "keep")) + led.default_state = LEDS_GPIO_DEFSTATE_KEEP; + else if(!strcmp(state, "on")) + led.default_state = LEDS_GPIO_DEFSTATE_ON; + else + led.default_state = LEDS_GPIO_DEFSTATE_OFF; + } ret = create_gpio_led(&led, &pdata->led_data[pdata->num_leds++], &ofdev->dev, NULL); diff --git a/drivers/leds/leds-lp3944.c b/drivers/leds/leds-lp3944.c new file mode 100644 index 000000000000..5946208ba26e --- /dev/null +++ b/drivers/leds/leds-lp3944.c @@ -0,0 +1,466 @@ +/* + * leds-lp3944.c - driver for National Semiconductor LP3944 Funlight Chip + * + * Copyright (C) 2009 Antonio Ospite + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +/* + * I2C driver for National Semiconductor LP3944 Funlight Chip + * http://www.national.com/pf/LP/LP3944.html + * + * This helper chip can drive up to 8 leds, with two programmable DIM modes; + * it could even be used as a gpio expander but this driver assumes it is used + * as a led controller. + * + * The DIM modes are used to set _blink_ patterns for leds, the pattern is + * specified supplying two parameters: + * - period: from 0s to 1.6s + * - duty cycle: percentage of the period the led is on, from 0 to 100 + * + * LP3944 can be found on Motorola A910 smartphone, where it drives the rgb + * leds, the camera flash light and the displays backlights. + */ + +#include +#include +#include +#include +#include +#include + +/* Read Only Registers */ +#define LP3944_REG_INPUT1 0x00 /* LEDs 0-7 InputRegister (Read Only) */ +#define LP3944_REG_REGISTER1 0x01 /* None (Read Only) */ + +#define LP3944_REG_PSC0 0x02 /* Frequency Prescaler 0 (R/W) */ +#define LP3944_REG_PWM0 0x03 /* PWM Register 0 (R/W) */ +#define LP3944_REG_PSC1 0x04 /* Frequency Prescaler 1 (R/W) */ +#define LP3944_REG_PWM1 0x05 /* PWM Register 1 (R/W) */ +#define LP3944_REG_LS0 0x06 /* LEDs 0-3 Selector (R/W) */ +#define LP3944_REG_LS1 0x07 /* LEDs 4-7 Selector (R/W) */ + +/* These registers are not used to control leds in LP3944, they can store + * arbitrary values which the chip will ignore. + */ +#define LP3944_REG_REGISTER8 0x08 +#define LP3944_REG_REGISTER9 0x09 + +#define LP3944_DIM0 0 +#define LP3944_DIM1 1 + +/* period in ms */ +#define LP3944_PERIOD_MIN 0 +#define LP3944_PERIOD_MAX 1600 + +/* duty cycle is a percentage */ +#define LP3944_DUTY_CYCLE_MIN 0 +#define LP3944_DUTY_CYCLE_MAX 100 + +#define ldev_to_led(c) container_of(c, struct lp3944_led_data, ldev) + +/* Saved data */ +struct lp3944_led_data { + u8 id; + enum lp3944_type type; + enum lp3944_status status; + struct led_classdev ldev; + struct i2c_client *client; + struct work_struct work; +}; + +struct lp3944_data { + struct mutex lock; + struct i2c_client *client; + struct lp3944_led_data leds[LP3944_LEDS_MAX]; +}; + +static int lp3944_reg_read(struct i2c_client *client, u8 reg, u8 *value) +{ + int tmp; + + tmp = i2c_smbus_read_byte_data(client, reg); + if (tmp < 0) + return -EINVAL; + + *value = tmp; + + return 0; +} + +static int lp3944_reg_write(struct i2c_client *client, u8 reg, u8 value) +{ + return i2c_smbus_write_byte_data(client, reg, value); +} + +/** + * Set the period for DIM status + * + * @client: the i2c client + * @dim: either LP3944_DIM0 or LP3944_DIM1 + * @period: period of a blink, that is a on/off cycle, expressed in ms. + */ +static int lp3944_dim_set_period(struct i2c_client *client, u8 dim, u16 period) +{ + u8 psc_reg; + u8 psc_value; + int err; + + if (dim == LP3944_DIM0) + psc_reg = LP3944_REG_PSC0; + else if (dim == LP3944_DIM1) + psc_reg = LP3944_REG_PSC1; + else + return -EINVAL; + + /* Convert period to Prescaler value */ + if (period > LP3944_PERIOD_MAX) + return -EINVAL; + + psc_value = (period * 255) / LP3944_PERIOD_MAX; + + err = lp3944_reg_write(client, psc_reg, psc_value); + + return err; +} + +/** + * Set the duty cycle for DIM status + * + * @client: the i2c client + * @dim: either LP3944_DIM0 or LP3944_DIM1 + * @duty_cycle: percentage of a period during which a led is ON + */ +static int lp3944_dim_set_dutycycle(struct i2c_client *client, u8 dim, + u8 duty_cycle) +{ + u8 pwm_reg; + u8 pwm_value; + int err; + + if (dim == LP3944_DIM0) + pwm_reg = LP3944_REG_PWM0; + else if (dim == LP3944_DIM1) + pwm_reg = LP3944_REG_PWM1; + else + return -EINVAL; + + /* Convert duty cycle to PWM value */ + if (duty_cycle > LP3944_DUTY_CYCLE_MAX) + return -EINVAL; + + pwm_value = (duty_cycle * 255) / LP3944_DUTY_CYCLE_MAX; + + err = lp3944_reg_write(client, pwm_reg, pwm_value); + + return err; +} + +/** + * Set the led status + * + * @led: a lp3944_led_data structure + * @status: one of LP3944_LED_STATUS_OFF + * LP3944_LED_STATUS_ON + * LP3944_LED_STATUS_DIM0 + * LP3944_LED_STATUS_DIM1 + */ +static int lp3944_led_set(struct lp3944_led_data *led, u8 status) +{ + struct lp3944_data *data = i2c_get_clientdata(led->client); + u8 id = led->id; + u8 reg; + u8 val = 0; + int err; + + dev_dbg(&led->client->dev, "%s: %s, status before normalization:%d\n", + __func__, led->ldev.name, status); + + switch (id) { + case LP3944_LED0: + case LP3944_LED1: + case LP3944_LED2: + case LP3944_LED3: + reg = LP3944_REG_LS0; + break; + case LP3944_LED4: + case LP3944_LED5: + case LP3944_LED6: + case LP3944_LED7: + id -= LP3944_LED4; + reg = LP3944_REG_LS1; + break; + default: + return -EINVAL; + } + + if (status > LP3944_LED_STATUS_DIM1) + return -EINVAL; + + /* invert only 0 and 1, leave unchanged the other values, + * remember we are abusing status to set blink patterns + */ + if (led->type == LP3944_LED_TYPE_LED_INVERTED && status < 2) + status = 1 - status; + + mutex_lock(&data->lock); + lp3944_reg_read(led->client, reg, &val); + + val &= ~(LP3944_LED_STATUS_MASK << (id << 1)); + val |= (status << (id << 1)); + + dev_dbg(&led->client->dev, "%s: %s, reg:%d id:%d status:%d val:%#x\n", + __func__, led->ldev.name, reg, id, status, val); + + /* set led status */ + err = lp3944_reg_write(led->client, reg, val); + mutex_unlock(&data->lock); + + return err; +} + +static int lp3944_led_set_blink(struct led_classdev *led_cdev, + unsigned long *delay_on, + unsigned long *delay_off) +{ + struct lp3944_led_data *led = ldev_to_led(led_cdev); + u16 period; + u8 duty_cycle; + int err; + + /* units are in ms */ + if (*delay_on + *delay_off > LP3944_PERIOD_MAX) + return -EINVAL; + + if (*delay_on == 0 && *delay_off == 0) { + /* Special case: the leds subsystem requires a default user + * friendly blink pattern for the LED. Let's blink the led + * slowly (1Hz). + */ + *delay_on = 500; + *delay_off = 500; + } + + period = (*delay_on) + (*delay_off); + + /* duty_cycle is the percentage of period during which the led is ON */ + duty_cycle = 100 * (*delay_on) / period; + + /* invert duty cycle for inverted leds, this has the same effect of + * swapping delay_on and delay_off + */ + if (led->type == LP3944_LED_TYPE_LED_INVERTED) + duty_cycle = 100 - duty_cycle; + + /* NOTE: using always the first DIM mode, this means that all leds + * will have the same blinking pattern. + * + * We could find a way later to have two leds blinking in hardware + * with different patterns at the same time, falling back to software + * control for the other ones. + */ + err = lp3944_dim_set_period(led->client, LP3944_DIM0, period); + if (err) + return err; + + err = lp3944_dim_set_dutycycle(led->client, LP3944_DIM0, duty_cycle); + if (err) + return err; + + dev_dbg(&led->client->dev, "%s: OK hardware accelerated blink!\n", + __func__); + + led->status = LP3944_LED_STATUS_DIM0; + schedule_work(&led->work); + + return 0; +} + +static void lp3944_led_set_brightness(struct led_classdev *led_cdev, + enum led_brightness brightness) +{ + struct lp3944_led_data *led = ldev_to_led(led_cdev); + + dev_dbg(&led->client->dev, "%s: %s, %d\n", + __func__, led_cdev->name, brightness); + + led->status = brightness; + schedule_work(&led->work); +} + +static void lp3944_led_work(struct work_struct *work) +{ + struct lp3944_led_data *led; + + led = container_of(work, struct lp3944_led_data, work); + lp3944_led_set(led, led->status); +} + +static int lp3944_configure(struct i2c_client *client, + struct lp3944_data *data, + struct lp3944_platform_data *pdata) +{ + int i, err = 0; + + for (i = 0; i < pdata->leds_size; i++) { + struct lp3944_led *pled = &pdata->leds[i]; + struct lp3944_led_data *led = &data->leds[i]; + led->client = client; + led->id = i; + + switch (pled->type) { + + case LP3944_LED_TYPE_LED: + case LP3944_LED_TYPE_LED_INVERTED: + led->type = pled->type; + led->status = pled->status; + led->ldev.name = pled->name; + led->ldev.max_brightness = 1; + led->ldev.brightness_set = lp3944_led_set_brightness; + led->ldev.blink_set = lp3944_led_set_blink; + led->ldev.flags = LED_CORE_SUSPENDRESUME; + + INIT_WORK(&led->work, lp3944_led_work); + err = led_classdev_register(&client->dev, &led->ldev); + if (err < 0) { + dev_err(&client->dev, + "couldn't register LED %s\n", + led->ldev.name); + goto exit; + } + + /* to expose the default value to userspace */ + led->ldev.brightness = led->status; + + /* Set the default led status */ + err = lp3944_led_set(led, led->status); + if (err < 0) { + dev_err(&client->dev, + "%s couldn't set STATUS %d\n", + led->ldev.name, led->status); + goto exit; + } + break; + + case LP3944_LED_TYPE_NONE: + default: + break; + + } + } + return 0; + +exit: + if (i > 0) + for (i = i - 1; i >= 0; i--) + switch (pdata->leds[i].type) { + + case LP3944_LED_TYPE_LED: + case LP3944_LED_TYPE_LED_INVERTED: + led_classdev_unregister(&data->leds[i].ldev); + cancel_work_sync(&data->leds[i].work); + break; + + case LP3944_LED_TYPE_NONE: + default: + break; + } + + return err; +} + +static int __devinit lp3944_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct lp3944_platform_data *lp3944_pdata = client->dev.platform_data; + struct lp3944_data *data; + + if (lp3944_pdata == NULL) { + dev_err(&client->dev, "no platform data\n"); + return -EINVAL; + } + + /* Let's see whether this adapter can support what we need. */ + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_BYTE_DATA)) { + dev_err(&client->dev, "insufficient functionality!\n"); + return -ENODEV; + } + + data = kzalloc(sizeof(struct lp3944_data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + data->client = client; + i2c_set_clientdata(client, data); + + mutex_init(&data->lock); + + dev_info(&client->dev, "lp3944 enabled\n"); + + lp3944_configure(client, data, lp3944_pdata); + return 0; +} + +static int __devexit lp3944_remove(struct i2c_client *client) +{ + struct lp3944_platform_data *pdata = client->dev.platform_data; + struct lp3944_data *data = i2c_get_clientdata(client); + int i; + + for (i = 0; i < pdata->leds_size; i++) + switch (data->leds[i].type) { + case LP3944_LED_TYPE_LED: + case LP3944_LED_TYPE_LED_INVERTED: + led_classdev_unregister(&data->leds[i].ldev); + cancel_work_sync(&data->leds[i].work); + break; + + case LP3944_LED_TYPE_NONE: + default: + break; + } + + kfree(data); + i2c_set_clientdata(client, NULL); + + return 0; +} + +/* lp3944 i2c driver struct */ +static const struct i2c_device_id lp3944_id[] = { + {"lp3944", 0}, + {} +}; + +MODULE_DEVICE_TABLE(i2c, lp3944_id); + +static struct i2c_driver lp3944_driver = { + .driver = { + .name = "lp3944", + }, + .probe = lp3944_probe, + .remove = __devexit_p(lp3944_remove), + .id_table = lp3944_id, +}; + +static int __init lp3944_module_init(void) +{ + return i2c_add_driver(&lp3944_driver); +} + +static void __exit lp3944_module_exit(void) +{ + i2c_del_driver(&lp3944_driver); +} + +module_init(lp3944_module_init); +module_exit(lp3944_module_exit); + +MODULE_AUTHOR("Antonio Ospite "); +MODULE_DESCRIPTION("LP3944 Fun Light Chip"); +MODULE_LICENSE("GPL"); diff --git a/drivers/leds/leds-pca9532.c b/drivers/leds/leds-pca9532.c index 3937244fdcab..dba8921240f2 100644 --- a/drivers/leds/leds-pca9532.c +++ b/drivers/leds/leds-pca9532.c @@ -35,7 +35,7 @@ struct pca9532_data { struct pca9532_led leds[16]; struct mutex update_lock; struct input_dev *idev; - struct work_struct work; + struct work_struct work; u8 pwm[2]; u8 psc[2]; }; @@ -87,14 +87,14 @@ static int pca9532_calcpwm(struct i2c_client *client, int pwm, int blink, if (b > 0xFF) return -EINVAL; data->pwm[pwm] = b; - data->psc[pwm] = blink; - return 0; + data->psc[pwm] = blink; + return 0; } static int pca9532_setpwm(struct i2c_client *client, int pwm) { - struct pca9532_data *data = i2c_get_clientdata(client); - mutex_lock(&data->update_lock); + struct pca9532_data *data = i2c_get_clientdata(client); + mutex_lock(&data->update_lock); i2c_smbus_write_byte_data(client, PCA9532_REG_PWM(pwm), data->pwm[pwm]); i2c_smbus_write_byte_data(client, PCA9532_REG_PSC(pwm), @@ -132,11 +132,11 @@ static void pca9532_set_brightness(struct led_classdev *led_cdev, led->state = PCA9532_ON; else { led->state = PCA9532_PWM0; /* Thecus: hardcode one pwm */ - err = pca9532_calcpwm(led->client, 0, 0, value); + err = pca9532_calcpwm(led->client, 0, 0, value); if (err) return; /* XXX: led api doesn't allow error code? */ } - schedule_work(&led->work); + schedule_work(&led->work); } static int pca9532_set_blink(struct led_classdev *led_cdev, @@ -145,7 +145,7 @@ static int pca9532_set_blink(struct led_classdev *led_cdev, struct pca9532_led *led = ldev_to_led(led_cdev); struct i2c_client *client = led->client; int psc; - int err = 0; + int err = 0; if (*delay_on == 0 && *delay_off == 0) { /* led subsystem ask us for a blink rate */ @@ -157,11 +157,11 @@ static int pca9532_set_blink(struct led_classdev *led_cdev, /* Thecus specific: only use PSC/PWM 0 */ psc = (*delay_on * 152-1)/1000; - err = pca9532_calcpwm(client, 0, psc, led_cdev->brightness); - if (err) - return err; - schedule_work(&led->work); - return 0; + err = pca9532_calcpwm(client, 0, psc, led_cdev->brightness); + if (err) + return err; + schedule_work(&led->work); + return 0; } static int pca9532_event(struct input_dev *dev, unsigned int type, @@ -178,15 +178,15 @@ static int pca9532_event(struct input_dev *dev, unsigned int type, else data->pwm[1] = 0; - schedule_work(&data->work); + schedule_work(&data->work); - return 0; + return 0; } static void pca9532_input_work(struct work_struct *work) { - struct pca9532_data *data; - data = container_of(work, struct pca9532_data, work); + struct pca9532_data *data; + data = container_of(work, struct pca9532_data, work); mutex_lock(&data->update_lock); i2c_smbus_write_byte_data(data->client, PCA9532_REG_PWM(1), data->pwm[1]); @@ -195,11 +195,11 @@ static void pca9532_input_work(struct work_struct *work) static void pca9532_led_work(struct work_struct *work) { - struct pca9532_led *led; - led = container_of(work, struct pca9532_led, work); - if (led->state == PCA9532_PWM0) - pca9532_setpwm(led->client, 0); - pca9532_setled(led); + struct pca9532_led *led; + led = container_of(work, struct pca9532_led, work); + if (led->state == PCA9532_PWM0) + pca9532_setpwm(led->client, 0); + pca9532_setled(led); } static int pca9532_configure(struct i2c_client *client, @@ -232,7 +232,7 @@ static int pca9532_configure(struct i2c_client *client, led->ldev.brightness = LED_OFF; led->ldev.brightness_set = pca9532_set_brightness; led->ldev.blink_set = pca9532_set_blink; - INIT_WORK(&led->work, pca9532_led_work); + INIT_WORK(&led->work, pca9532_led_work); err = led_classdev_register(&client->dev, &led->ldev); if (err < 0) { dev_err(&client->dev, @@ -262,11 +262,11 @@ static int pca9532_configure(struct i2c_client *client, BIT_MASK(SND_TONE); data->idev->event = pca9532_event; input_set_drvdata(data->idev, data); - INIT_WORK(&data->work, pca9532_input_work); + INIT_WORK(&data->work, pca9532_input_work); err = input_register_device(data->idev); if (err) { input_free_device(data->idev); - cancel_work_sync(&data->work); + cancel_work_sync(&data->work); data->idev = NULL; goto exit; } @@ -283,13 +283,13 @@ exit: break; case PCA9532_TYPE_LED: led_classdev_unregister(&data->leds[i].ldev); - cancel_work_sync(&data->leds[i].work); + cancel_work_sync(&data->leds[i].work); break; case PCA9532_TYPE_N2100_BEEP: if (data->idev != NULL) { input_unregister_device(data->idev); input_free_device(data->idev); - cancel_work_sync(&data->work); + cancel_work_sync(&data->work); data->idev = NULL; } break; @@ -340,13 +340,13 @@ static int pca9532_remove(struct i2c_client *client) break; case PCA9532_TYPE_LED: led_classdev_unregister(&data->leds[i].ldev); - cancel_work_sync(&data->leds[i].work); + cancel_work_sync(&data->leds[i].work); break; case PCA9532_TYPE_N2100_BEEP: if (data->idev != NULL) { input_unregister_device(data->idev); input_free_device(data->idev); - cancel_work_sync(&data->work); + cancel_work_sync(&data->work); data->idev = NULL; } break; diff --git a/include/linux/leds-lp3944.h b/include/linux/leds-lp3944.h new file mode 100644 index 000000000000..afc9f9fd70f5 --- /dev/null +++ b/include/linux/leds-lp3944.h @@ -0,0 +1,53 @@ +/* + * leds-lp3944.h - platform data structure for lp3944 led controller + * + * Copyright (C) 2009 Antonio Ospite + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef __LINUX_LEDS_LP3944_H +#define __LINUX_LEDS_LP3944_H + +#include +#include + +#define LP3944_LED0 0 +#define LP3944_LED1 1 +#define LP3944_LED2 2 +#define LP3944_LED3 3 +#define LP3944_LED4 4 +#define LP3944_LED5 5 +#define LP3944_LED6 6 +#define LP3944_LED7 7 +#define LP3944_LEDS_MAX 8 + +#define LP3944_LED_STATUS_MASK 0x03 +enum lp3944_status { + LP3944_LED_STATUS_OFF = 0x0, + LP3944_LED_STATUS_ON = 0x1, + LP3944_LED_STATUS_DIM0 = 0x2, + LP3944_LED_STATUS_DIM1 = 0x3 +}; + +enum lp3944_type { + LP3944_LED_TYPE_NONE, + LP3944_LED_TYPE_LED, + LP3944_LED_TYPE_LED_INVERTED, +}; + +struct lp3944_led { + char *name; + enum lp3944_type type; + enum lp3944_status status; +}; + +struct lp3944_platform_data { + struct lp3944_led leds[LP3944_LEDS_MAX]; + u8 leds_size; +}; + +#endif /* __LINUX_LEDS_LP3944_H */ diff --git a/include/linux/leds.h b/include/linux/leds.h index 376fe07732ea..d8bf9665e70c 100644 --- a/include/linux/leds.h +++ b/include/linux/leds.h @@ -45,7 +45,10 @@ struct led_classdev { /* Get LED brightness level */ enum led_brightness (*brightness_get)(struct led_classdev *led_cdev); - /* Activate hardware accelerated blink */ + /* Activate hardware accelerated blink, delays are in + * miliseconds and if none is provided then a sensible default + * should be chosen. The call can adjust the timings if it can't + * match the values specified exactly. */ int (*blink_set)(struct led_classdev *led_cdev, unsigned long *delay_on, unsigned long *delay_off); @@ -141,9 +144,14 @@ struct gpio_led { const char *name; const char *default_trigger; unsigned gpio; - u8 active_low : 1; - u8 retain_state_suspended : 1; + unsigned active_low : 1; + unsigned retain_state_suspended : 1; + unsigned default_state : 2; + /* default_state should be one of LEDS_GPIO_DEFSTATE_(ON|OFF|KEEP) */ }; +#define LEDS_GPIO_DEFSTATE_OFF 0 +#define LEDS_GPIO_DEFSTATE_ON 1 +#define LEDS_GPIO_DEFSTATE_KEEP 2 struct gpio_led_platform_data { int num_leds;