USB/xhci: Enable remote wakeup for USB3 devices.
When the USB 3.0 hub support went in, I disabled selective suspend for all external USB 3.0 hubs because they used a different mechanism to enable remote wakeup. In fact, other USB 3.0 devices that could signal remote wakeup would have been prevented from going into suspend because they would have stalled the SetFeature Device Remote Wakeup request. This patch adds support for the USB 3.0 way of enabling remote wake up (with a SetFeature Function Suspend request), and enables selective suspend for all hubs during hub_probe. It assumes that all USB 3.0 have only one "function" as defined by the interface association descriptor, which is true of all the USB 3.0 devices I've seen so far. FIXME if that turns out to change later. After a device signals a remote wakeup, it is supposed to send a Device Notification packet to the host controller, signaling which function sent the remote wakeup. The host can then put any other functions back into function suspend. Since we don't have support for function suspend (and no devices currently support it), we'll just assume the hub function will resume the device properly when it received the port status change notification, and simply ignore any device notification events from the xHCI host controller. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This commit is contained in:
Родитель
d93814cfad
Коммит
623bef9e03
|
@ -2421,11 +2421,26 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg)
|
|||
* we don't explicitly enable it here.
|
||||
*/
|
||||
if (udev->do_remote_wakeup) {
|
||||
status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
|
||||
USB_REQ_SET_FEATURE, USB_RECIP_DEVICE,
|
||||
USB_DEVICE_REMOTE_WAKEUP, 0,
|
||||
NULL, 0,
|
||||
USB_CTRL_SET_TIMEOUT);
|
||||
if (!hub_is_superspeed(hub->hdev)) {
|
||||
status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
|
||||
USB_REQ_SET_FEATURE, USB_RECIP_DEVICE,
|
||||
USB_DEVICE_REMOTE_WAKEUP, 0,
|
||||
NULL, 0,
|
||||
USB_CTRL_SET_TIMEOUT);
|
||||
} else {
|
||||
/* Assume there's only one function on the USB 3.0
|
||||
* device and enable remote wake for the first
|
||||
* interface. FIXME if the interface association
|
||||
* descriptor shows there's more than one function.
|
||||
*/
|
||||
status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
|
||||
USB_REQ_SET_FEATURE,
|
||||
USB_RECIP_INTERFACE,
|
||||
USB_INTRF_FUNC_SUSPEND,
|
||||
USB_INTRF_FUNC_SUSPEND_RW,
|
||||
NULL, 0,
|
||||
USB_CTRL_SET_TIMEOUT);
|
||||
}
|
||||
if (status) {
|
||||
dev_dbg(&udev->dev, "won't remote wakeup, status %d\n",
|
||||
status);
|
||||
|
|
|
@ -2141,7 +2141,7 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
|
|||
unsigned int val, val2;
|
||||
u64 val_64;
|
||||
struct xhci_segment *seg;
|
||||
u32 page_size;
|
||||
u32 page_size, temp;
|
||||
int i;
|
||||
|
||||
page_size = xhci_readl(xhci, &xhci->op_regs->page_size);
|
||||
|
@ -2324,6 +2324,15 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
|
|||
|
||||
INIT_LIST_HEAD(&xhci->lpm_failed_devs);
|
||||
|
||||
/* Enable USB 3.0 device notifications for function remote wake, which
|
||||
* is necessary for allowing USB 3.0 devices to do remote wakeup from
|
||||
* U3 (device suspend).
|
||||
*/
|
||||
temp = xhci_readl(xhci, &xhci->op_regs->dev_notification);
|
||||
temp &= ~DEV_NOTE_MASK;
|
||||
temp |= DEV_NOTE_FWAKE;
|
||||
xhci_writel(xhci, temp, &xhci->op_regs->dev_notification);
|
||||
|
||||
return 0;
|
||||
|
||||
fail:
|
||||
|
|
|
@ -1237,6 +1237,24 @@ static unsigned int find_faked_portnum_from_hw_portnum(struct usb_hcd *hcd,
|
|||
return num_similar_speed_ports;
|
||||
}
|
||||
|
||||
static void handle_device_notification(struct xhci_hcd *xhci,
|
||||
union xhci_trb *event)
|
||||
{
|
||||
u32 slot_id;
|
||||
|
||||
slot_id = TRB_TO_SLOT_ID(event->generic.field[3]);
|
||||
if (!xhci->devs[slot_id])
|
||||
xhci_warn(xhci, "Device Notification event for "
|
||||
"unused slot %u\n", slot_id);
|
||||
else
|
||||
xhci_dbg(xhci, "Device Notification event for slot ID %u\n",
|
||||
slot_id);
|
||||
/* XXX should we kick khubd for the parent hub? It should have send an
|
||||
* interrupt transfer when the port started signaling resume, so there's
|
||||
* probably no need to do so.
|
||||
*/
|
||||
}
|
||||
|
||||
static void handle_port_status(struct xhci_hcd *xhci,
|
||||
union xhci_trb *event)
|
||||
{
|
||||
|
@ -2282,6 +2300,9 @@ static int xhci_handle_event(struct xhci_hcd *xhci)
|
|||
else
|
||||
update_ptrs = 0;
|
||||
break;
|
||||
case TRB_TYPE(TRB_DEV_NOTE):
|
||||
handle_device_notification(xhci, event);
|
||||
break;
|
||||
default:
|
||||
if ((le32_to_cpu(event->event_cmd.flags) & TRB_TYPE_BITMASK) >=
|
||||
TRB_TYPE(48))
|
||||
|
|
Загрузка…
Ссылка в новой задаче