dt-bindings: net: dsa: sja1105: convert to YAML schema

Since the sja1105 driver no longer has any custom device tree
properties, the conversion is trivial.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml

@@ -0,0 +1,89 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/nxp,sja1105.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP SJA1105 Automotive Ethernet Switch Family Device Tree Bindings
+
+description:
+  The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944.pdf) of at
+  least one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum
+  cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed
+  depends on the SPI bus master driver.
+
+allOf:
+  - $ref: "dsa.yaml#"
+
+maintainers:
+  - Vladimir Oltean <vladimir.oltean@nxp.com>
+
+properties:
+  compatible:
+    enum:
+      - nxp,sja1105e
+      - nxp,sja1105t
+      - nxp,sja1105p
+      - nxp,sja1105q
+      - nxp,sja1105r
+      - nxp,sja1105s
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    spi {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            ethernet-switch@1 {
+                    reg = <0x1>;
+                    compatible = "nxp,sja1105t";
+
+                    ethernet-ports {
+                            #address-cells = <1>;
+                            #size-cells = <0>;
+
+                            port@0 {
+                                    phy-handle = <&rgmii_phy6>;
+                                    phy-mode = "rgmii-id";
+                                    reg = <0>;
+                            };
+
+                            port@1 {
+                                    phy-handle = <&rgmii_phy3>;
+                                    phy-mode = "rgmii-id";
+                                    reg = <1>;
+                            };
+
+                            port@2 {
+                                    phy-handle = <&rgmii_phy4>;
+                                    phy-mode = "rgmii-id";
+                                    reg = <2>;
+                            };
+
+                            port@3 {
+                                    phy-mode = "rgmii-id";
+                                    reg = <3>;
+                            };
+
+                            port@4 {
+                                    ethernet = <&enet2>;
+                                    phy-mode = "rgmii";
+                                    reg = <4>;
+
+                                    fixed-link {
+                                            speed = <1000>;
+                                            full-duplex;
+                                    };
+                            };
+                    };
+            };
+    };

Documentation/devicetree/bindings/net/dsa/sja1105.txt

@@ -1,121 +0,0 @@
-NXP SJA1105 switch driver
-=========================
-
-Required properties:
-
-- compatible:
-	Must be one of:
-	- "nxp,sja1105e"
-	- "nxp,sja1105t"
-	- "nxp,sja1105p"
-	- "nxp,sja1105q"
-	- "nxp,sja1105r"
-	- "nxp,sja1105s"
-
-	Although the device ID could be detected at runtime, explicit bindings
-	are required in order to be able to statically check their validity.
-	For example, SGMII can only be specified on port 4 of R and S devices,
-	and the non-SGMII devices, while pin-compatible, are not equal in terms
-	of support for RGMII internal delays (supported on P/Q/R/S, but not on
-	E/T).
-
-See Documentation/devicetree/bindings/net/dsa/dsa.txt for the list of standard
-DSA required and optional properties.
-
-Other observations
-------------------
-
-The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944) of at least
-one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum
-cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed
-depends on the SPI bus master driver.
-
-Example
--------
-
-Ethernet switch connected via SPI to the host, CPU port wired to enet2:
-
-arch/arm/boot/dts/ls1021a-tsn.dts:
-
-/* SPI controller of the LS1021 */
-&dspi0 {
-	sja1105@1 {
-		reg = <0x1>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "nxp,sja1105t";
-		spi-max-frequency = <4000000>;
-		fsl,spi-cs-sck-delay = <1000>;
-		fsl,spi-sck-cs-delay = <1000>;
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			port@0 {
-				/* ETH5 written on chassis */
-				label = "swp5";
-				phy-handle = <&rgmii_phy6>;
-				phy-mode = "rgmii-id";
-				reg = <0>;
-			};
-			port@1 {
-				/* ETH2 written on chassis */
-				label = "swp2";
-				phy-handle = <&rgmii_phy3>;
-				phy-mode = "rgmii-id";
-				reg = <1>;
-			};
-			port@2 {
-				/* ETH3 written on chassis */
-				label = "swp3";
-				phy-handle = <&rgmii_phy4>;
-				phy-mode = "rgmii-id";
-				reg = <2>;
-			};
-			port@3 {
-				/* ETH4 written on chassis */
-				phy-handle = <&rgmii_phy5>;
-				label = "swp4";
-				phy-mode = "rgmii-id";
-				reg = <3>;
-			};
-			port@4 {
-				/* Internal port connected to eth2 */
-				ethernet = <&enet2>;
-				phy-mode = "rgmii";
-				reg = <4>;
-
-				fixed-link {
-					speed = <1000>;
-					full-duplex;
-				};
-			};
-		};
-	};
-};
-
-/* MDIO controller of the LS1021 */
-&mdio0 {
-	/* BCM5464 */
-	rgmii_phy3: ethernet-phy@3 {
-		reg = <0x3>;
-	};
-	rgmii_phy4: ethernet-phy@4 {
-		reg = <0x4>;
-	};
-	rgmii_phy5: ethernet-phy@5 {
-		reg = <0x5>;
-	};
-	rgmii_phy6: ethernet-phy@6 {
-		reg = <0x6>;
-	};
-};
-
-/* Ethernet master port of the LS1021 */
-&enet2 {
-	phy-connection-type = "rgmii";
-	status = "ok";
-	fixed-link {
-		speed = <1000>;
-		full-duplex;
-	};
-};