bnx2x: Load firmware in open() instead of probe()

Loading firmware when actually bringing eth device up.
This also will allow driver to be insmoded when filesystem with
firmware files is not available yet.

Suggested by Stephen Hemminger <shemminger@vyatta.com>

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/bnx2x/bnx2x_cmn.c

@@ -20,6 +20,7 @@
 #include <linux/ip.h>
 #include <linux/ipv6.h>
 #include <net/ip6_checksum.h>
+#include <linux/firmware.h>
 #include "bnx2x_cmn.h"
 
 #ifdef BCM_VLAN
@@ -1206,12 +1207,27 @@ static int bnx2x_set_num_queues(struct bnx2x *bp)
 	return rc;
 }
 
+static void bnx2x_release_firmware(struct bnx2x *bp)
+{
+	kfree(bp->init_ops_offsets);
+	kfree(bp->init_ops);
+	kfree(bp->init_data);
+	release_firmware(bp->firmware);
+}
+
 /* must be called with rtnl_lock */
 int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
 {
 	u32 load_code;
 	int i, rc;
 
+	/* Set init arrays */
+	rc = bnx2x_init_firmware(bp);
+	if (rc) {
+		BNX2X_ERR("Error loading firmware\n");
+		return rc;
+	}
+
 #ifdef BNX2X_STOP_ON_ERROR
 	if (unlikely(bp->panic))
 		return -EPERM;
@@ -1427,6 +1443,8 @@ int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
 #endif
 	bnx2x_inc_load_cnt(bp);
 
+	bnx2x_release_firmware(bp);
+
 	return 0;
 
 #ifdef BCM_CNIC
@@ -1454,6 +1472,8 @@ load_error1:
 		netif_napi_del(&bnx2x_fp(bp, i, napi));
 	bnx2x_free_mem(bp);
 
+	bnx2x_release_firmware(bp);
+
 	return rc;
 }
 

drivers/net/bnx2x/bnx2x_cmn.h

@@ -114,6 +114,15 @@ void bnx2x_int_enable(struct bnx2x *bp);
  */
 void bnx2x_int_disable_sync(struct bnx2x *bp, int disable_hw);
 
+/**
+ * Loads device firmware
+ *
+ * @param bp
+ *
+ * @return int
+ */
+int bnx2x_init_firmware(struct bnx2x *bp);
+
 /**
  * Init HW blocks according to current initialization stage:
  * COMMON, PORT or FUNCTION.

drivers/net/bnx2x/bnx2x_main.c

@@ -7254,7 +7254,7 @@ static void __devinit bnx2x_get_pcie_width_speed(struct bnx2x *bp,
 	*speed = (val & PCICFG_LINK_SPEED) >> PCICFG_LINK_SPEED_SHIFT;
 }
 
-static int __devinit bnx2x_check_firmware(struct bnx2x *bp)
+static int bnx2x_check_firmware(struct bnx2x *bp)
 {
 	const struct firmware *firmware = bp->firmware;
 	struct bnx2x_fw_file_hdr *fw_hdr;
@@ -7365,7 +7365,7 @@ do {									\
 	     (u8 *)bp->arr, len);					\
 } while (0)
 
-static int __devinit bnx2x_init_firmware(struct bnx2x *bp, struct device *dev)
+int bnx2x_init_firmware(struct bnx2x *bp)
 {
 	const char *fw_file_name;
 	struct bnx2x_fw_file_hdr *fw_hdr;
@@ -7376,21 +7376,21 @@ static int __devinit bnx2x_init_firmware(struct bnx2x *bp, struct device *dev)
 	else if (CHIP_IS_E1H(bp))
 		fw_file_name = FW_FILE_NAME_E1H;
 	else {
-		dev_err(dev, "Unsupported chip revision\n");
+		BNX2X_ERR("Unsupported chip revision\n");
 		return -EINVAL;
 	}
 
-	dev_info(dev, "Loading %s\n", fw_file_name);
+	BNX2X_DEV_INFO("Loading %s\n", fw_file_name);
 
-	rc = request_firmware(&bp->firmware, fw_file_name, dev);
+	rc = request_firmware(&bp->firmware, fw_file_name, &bp->pdev->dev);
 	if (rc) {
-		dev_err(dev, "Can't load firmware file %s\n", fw_file_name);
+		BNX2X_ERR("Can't load firmware file %s\n", fw_file_name);
 		goto request_firmware_exit;
 	}
 
 	rc = bnx2x_check_firmware(bp);
 	if (rc) {
-		dev_err(dev, "Corrupt firmware file %s\n", fw_file_name);
+		BNX2X_ERR("Corrupt firmware file %s\n", fw_file_name);
 		goto request_firmware_exit;
 	}
 
@@ -7468,13 +7468,6 @@ static int __devinit bnx2x_init_one(struct pci_dev *pdev,
 	if (rc)
 		goto init_one_exit;
 
-	/* Set init arrays */
-	rc = bnx2x_init_firmware(bp, &pdev->dev);
-	if (rc) {
-		dev_err(&pdev->dev, "Error loading firmware\n");
-		goto init_one_exit;
-	}
-
 	rc = register_netdev(dev);
 	if (rc) {
 		dev_err(&pdev->dev, "Cannot register net device\n");
@@ -7525,11 +7518,6 @@ static void __devexit bnx2x_remove_one(struct pci_dev *pdev)
 	/* Make sure RESET task is not scheduled before continuing */
 	cancel_delayed_work_sync(&bp->reset_task);
 
-	kfree(bp->init_ops_offsets);
-	kfree(bp->init_ops);
-	kfree(bp->init_data);
-	release_firmware(bp->firmware);
-
 	if (bp->regview)
 		iounmap(bp->regview);