Documentation/networking: Update Intel Wired LAN docs
- Update the Intel Wired LAN documentation with the latest URL for ethtool. - replace "Ethtool" with "ethtool" Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
This commit is contained in:
Jeff Kirsher
Родитель
e1928c86c4
Коммит
68f20d948c
|
|
@ -72,7 +72,7 @@ Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data
|
|||
ethtool -G eth? tx n, where n is the number of desired tx descriptors.
|
||||
|
||||
Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by
|
||||
default. Ethtool can be used as follows to force speed/duplex.
|
||||
default. The ethtool utility can be used as follows to force speed/duplex.
|
||||
|
||||
ethtool -s eth? autoneg off speed {10|100} duplex {full|half}
|
||||
|
||||
|
|
@ -126,30 +126,21 @@ Additional Configurations
|
|||
-------
|
||||
|
||||
The driver utilizes the ethtool interface for driver configuration and
|
||||
diagnostics, as well as displaying statistical information. Ethtool
|
||||
diagnostics, as well as displaying statistical information. The ethtool
|
||||
version 1.6 or later is required for this functionality.
|
||||
|
||||
The latest release of ethtool can be found from
|
||||
http://sourceforge.net/projects/gkernel.
|
||||
|
||||
NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support
|
||||
for a more complete ethtool feature set can be enabled by upgrading
|
||||
ethtool to ethtool-1.8.1.
|
||||
|
||||
http://ftp.kernel.org/pub/software/network/ethtool/
|
||||
|
||||
Enabling Wake on LAN* (WoL)
|
||||
---------------------------
|
||||
WoL is provided through the Ethtool* utility. Ethtool is included with Red
|
||||
Hat* 8.0. For other Linux distributions, download and install Ethtool from
|
||||
the following website: http://sourceforge.net/projects/gkernel.
|
||||
|
||||
For instructions on enabling WoL with Ethtool, refer to the Ethtool man page.
|
||||
WoL is provided through the ethtool* utility. For instructions on enabling
|
||||
WoL with ethtool, refer to the ethtool man page.
|
||||
|
||||
WoL will be enabled on the system during the next shut down or reboot. For
|
||||
this driver version, in order to enable WoL, the e100 driver must be
|
||||
loaded when shutting down or rebooting the system.
|
||||
|
||||
|
||||
NAPI
|
||||
----
|
||||
|
||||
|
|
|
|||
|
|
@ -431,15 +431,15 @@ Additional Configurations
|
|||
Ethtool
|
||||
-------
|
||||
The driver utilizes the ethtool interface for driver configuration and
|
||||
diagnostics, as well as displaying statistical information. Ethtool
|
||||
diagnostics, as well as displaying statistical information. The ethtool
|
||||
version 1.6 or later is required for this functionality.
|
||||
|
||||
The latest release of ethtool can be found from
|
||||
http://sourceforge.net/projects/gkernel.
|
||||
http://ftp.kernel.org/pub/software/network/ethtool/
|
||||
|
||||
Enabling Wake on LAN* (WoL)
|
||||
---------------------------
|
||||
WoL is configured through the Ethtool* utility.
|
||||
WoL is configured through the ethtool* utility.
|
||||
|
||||
WoL will be enabled on the system during the next shut down or reboot.
|
||||
For this driver version, in order to enable WoL, the e1000 driver must be
|
||||
|
|
|
|||
|
|
@ -269,26 +269,26 @@ Additional Configurations
|
|||
-------
|
||||
The driver utilizes the ethtool interface for driver configuration and
|
||||
diagnostics, as well as displaying statistical information. We
|
||||
strongly recommend downloading the latest version of Ethtool at:
|
||||
strongly recommend downloading the latest version of ethtool at:
|
||||
|
||||
http://sourceforge.net/projects/gkernel.
|
||||
http://ftp.kernel.org/pub/software/network/ethtool/
|
||||
|
||||
Speed and Duplex
|
||||
----------------
|
||||
Speed and Duplex are configured through the Ethtool* utility. For
|
||||
instructions, refer to the Ethtool man page.
|
||||
Speed and Duplex are configured through the ethtool* utility. For
|
||||
instructions, refer to the ethtool man page.
|
||||
|
||||
Enabling Wake on LAN* (WoL)
|
||||
---------------------------
|
||||
WoL is configured through the Ethtool* utility. For instructions on
|
||||
enabling WoL with Ethtool, refer to the Ethtool man page.
|
||||
WoL is configured through the ethtool* utility. For instructions on
|
||||
enabling WoL with ethtool, refer to the ethtool man page.
|
||||
|
||||
WoL will be enabled on the system during the next shut down or reboot.
|
||||
For this driver version, in order to enable WoL, the e1000e driver must be
|
||||
loaded when shutting down or rebooting the system.
|
||||
|
||||
In most cases Wake On LAN is only supported on port A for multiple port
|
||||
adapters. To verify if a port supports Wake on Lan run Ethtool eth<X>.
|
||||
adapters. To verify if a port supports Wake on Lan run ethtool eth<X>.
|
||||
|
||||
Support
|
||||
=======
|
||||
|
|
|
|||
|
|
@ -62,15 +62,15 @@ Additional Configurations
|
|||
-------
|
||||
The driver utilizes the ethtool interface for driver configuration and
|
||||
diagnostics, as well as displaying statistical information. The latest
|
||||
version of Ethtool can be found at:
|
||||
version of ethtool can be found at:
|
||||
|
||||
http://ftp.kernel.org/pub/software/network/ethtool/
|
||||
|
||||
Enabling Wake on LAN* (WoL)
|
||||
---------------------------
|
||||
WoL is configured through the Ethtool* utility.
|
||||
WoL is configured through the ethtool* utility.
|
||||
|
||||
For instructions on enabling WoL with Ethtool, refer to the Ethtool man page.
|
||||
For instructions on enabling WoL with ethtool, refer to the ethtool man page.
|
||||
|
||||
WoL will be enabled on the system during the next shut down or reboot.
|
||||
For this driver version, in order to enable WoL, the igb driver must be
|
||||
|
|
|
|||
|
|
@ -58,11 +58,11 @@ Additional Configurations
|
|||
Ethtool
|
||||
-------
|
||||
The driver utilizes the ethtool interface for driver configuration and
|
||||
diagnostics, as well as displaying statistical information. Ethtool
|
||||
diagnostics, as well as displaying statistical information. The ethtool
|
||||
version 3.0 or later is required for this functionality, although we
|
||||
strongly recommend downloading the latest version at:
|
||||
|
||||
http://sourceforge.net/projects/gkernel.
|
||||
http://ftp.kernel.org/pub/software/network/ethtool/
|
||||
|
||||
Support
|
||||
=======
|
||||
|
|
|
|||
|
|
@ -309,15 +309,15 @@ Additional Configurations
|
|||
Ethtool
|
||||
-------
|
||||
The driver utilizes the ethtool interface for driver configuration and
|
||||
diagnostics, as well as displaying statistical information. Ethtool
|
||||
diagnostics, as well as displaying statistical information. The ethtool
|
||||
version 1.6 or later is required for this functionality.
|
||||
|
||||
The latest release of ethtool can be found from
|
||||
http://sourceforge.net/projects/gkernel
|
||||
http://ftp.kernel.org/pub/software/network/ethtool/
|
||||
|
||||
NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support
|
||||
for a more complete ethtool feature set can be enabled by upgrading
|
||||
to the latest version.
|
||||
NOTE: The ethtool version 1.6 only supports a limited set of ethtool options.
|
||||
Support for a more complete ethtool feature set can be enabled by
|
||||
upgrading to the latest version.
|
||||
|
||||
|
||||
NAPI
|
||||
|
|
|
|||
|
|
@ -34,7 +34,7 @@ is an Intel(R) Ethernet Server Adapter X520-2, then it only supports Intel
|
|||
optics and/or the direct attach cables listed below.
|
||||
|
||||
When 82599-based SFP+ devices are connected back to back, they should be set to
|
||||
the same Speed setting via Ethtool. Results may vary if you mix speed settings.
|
||||
the same Speed setting via ethtool. Results may vary if you mix speed settings.
|
||||
82598-based adapters support all passive direct attach cables that comply
|
||||
with SFF-8431 v4.1 and SFF-8472 v10.4 specifications. Active direct attach
|
||||
cables are not supported.
|
||||
|
|
@ -110,7 +110,7 @@ threshold. When rx is enabled, the transmit unit will halt for the time delay
|
|||
specified when a PAUSE frame is received.
|
||||
|
||||
Flow Control is enabled by default. If you want to disable a flow control
|
||||
capable link partner, use Ethtool:
|
||||
capable link partner, use ethtool:
|
||||
|
||||
ethtool -A eth? autoneg off RX off TX off
|
||||
|
||||
|
|
@ -181,10 +181,10 @@ Additional Configurations
|
|||
-------
|
||||
The driver utilizes the ethtool interface for driver configuration and
|
||||
diagnostics, as well as displaying statistical information. The latest
|
||||
Ethtool version is required for this functionality.
|
||||
ethtool version is required for this functionality.
|
||||
|
||||
The latest release of ethtool can be found from
|
||||
http://sourceforge.net/projects/gkernel.
|
||||
http://ftp.kernel.org/pub/software/network/ethtool/
|
||||
|
||||
FCoE
|
||||
----
|
||||
|
|
|
|||
Загрузка…
Ссылка в новой задаче