docs: README.buddha: convert to ReST and add to m68k book

Adjust the file for it to be properly parsed by Sphinx, adding
it to the index of the book it belongs.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

Documentation/m68k/buddha-driver.rst

@@ -1,3 +1,6 @@
+=====================================
+Amiga Buddha and Catweasel IDE Driver
+=====================================
 
 The Amiga Buddha and Catweasel IDE Driver (part of ide.c) was written by
 Geert Uytterhoeven based on the following specifications:
@@ -12,12 +15,12 @@ described  in  their  manuals, no tricks have been used (for
 example leaving some address lines out of the equations...).
 If you want to configure the board yourself (for example let
 a  Linux  kernel  configure the card), look at the Commodore
-Docs.  Reading the nibbles should give this information:
+Docs.  Reading the nibbles should give this information::
 
-Vendor number: 4626 ($1212)
-product number: 0 (42 for Catweasel Z-II)
-Serial number: 0
-Rom-vector: $1000
+  Vendor number: 4626 ($1212)
+  product number: 0 (42 for Catweasel Z-II)
+  Serial number: 0
+  Rom-vector: $1000
 
 The  card  should be a Z-II board, size 64K, not for freemem
 list, Rom-Vektor is valid, no second Autoconfig-board on the
@@ -34,6 +37,7 @@ otherwise your chance is only 1:16 to find the board :-).
 
 The local memory-map is even active when mapped to $e8:
 
+==============  ===========================================
 $0-$7e		Autokonfig-space, see Z-II docs.
 
 $80-$7fd	reserved
@@ -50,10 +54,10 @@ $a00-$aff	IDE-Select 2 (Port 1, Register set 0)
 $b00-$bff	IDE-Select 3 (Port 1, Register set 1)
 
 $c00-$cff	IDE-Select 4 (Port 2, Register set 0,
-                          Catweasel only!)
+                Catweasel only!)
 
 $d00-$dff	IDE-Select 5 (Port 3, Register set 1,
-			      Catweasel only!)
+		Catweasel only!)
 
 $e00-$eff	local expansion port, on Catweasel Z-II the
 		Catweasel registers are also mapped here.
@@ -94,6 +98,7 @@ $1000-$ffff	Buddha-Rom with offset $1000 in the rom
 		chip. The addresses $0 to $fff of the rom
 		chip cannot be read. Rom is Byte-wide and
 		mapped to even addresses.
+==============  ===========================================
 
 The  IDE ports issue an INT2.  You can read the level of the
 IRQ-lines  of  the  IDE-ports by reading from the three (two
@@ -128,7 +133,8 @@ must  always  be set to 1 to be compatible with later Buddha
 versions  (if  I'll  ever  update this one).  I presume that
 I'll  never use the lower four bits, but they have to be set
 to 1 by definition.
-  The  values in this table have to be shifted 5 bits to the
+
+The  values in this table have to be shifted 5 bits to the
 left and or'd with $1f (this sets the lower 5 bits).
 
 All  the timings have in common:  Select and IOR/IOW rise at
@@ -138,38 +144,30 @@ values  are no multiple of 71.  One clock-cycle is 71ns long
 (exactly 70,5 at 14,18 Mhz on PAL systems).
 
 value 0 (Default after reset)
-
-497ns Select (7 clock cycles) , IOR/IOW after 172ns (2 clock cycles)
-(same timing as the Amiga 1200 does on it's IDE port without
-accelerator card)
+  497ns Select (7 clock cycles) , IOR/IOW after 172ns (2 clock cycles)
+  (same timing as the Amiga 1200 does on it's IDE port without
+  accelerator card)
 
 value 1
-
-639ns Select (9 clock cycles), IOR/IOW after 243ns (3 clock cycles)
+  639ns Select (9 clock cycles), IOR/IOW after 243ns (3 clock cycles)
 
 value 2
-
-781ns Select (11 clock cycles), IOR/IOW after 314ns (4 clock cycles)
+  781ns Select (11 clock cycles), IOR/IOW after 314ns (4 clock cycles)
 
 value 3
-
-355ns Select (5 clock cycles), IOR/IOW after 101ns (1 clock cycle)
+  355ns Select (5 clock cycles), IOR/IOW after 101ns (1 clock cycle)
 
 value 4
-
-355ns Select (5 clock cycles), IOR/IOW after 172ns (2 clock cycles)
+  355ns Select (5 clock cycles), IOR/IOW after 172ns (2 clock cycles)
 
 value 5
-
-355ns Select (5 clock cycles), IOR/IOW after 243ns (3 clock cycles)
+  355ns Select (5 clock cycles), IOR/IOW after 243ns (3 clock cycles)
 
 value 6
-
-1065ns Select (15 clock cycles), IOR/IOW after 314ns (4 clock cycles)
+  1065ns Select (15 clock cycles), IOR/IOW after 314ns (4 clock cycles)
 
 value 7
-
-355ns Select, (5 clock cycles), IOR/IOW after 101ns (1 clock cycle)
+  355ns Select, (5 clock cycles), IOR/IOW after 101ns (1 clock cycle)
 
 When accessing IDE registers with A6=1 (for example $84x),
 the timing will always be mode 0 8-bit compatible, no matter
@@ -204,7 +202,8 @@ always  shows a "no IRQ here" on the Buddha, and accesses to
 the  third  IDE  port  are  going into data's Nirwana on the
 Buddha.
 
-			    Jens Schönfeld february 19th, 1997
-					updated may 27th, 1997
-			     eMail: sysop@nostlgic.tng.oche.de
+Jens Schönfeld february 19th, 1997
 
+updated may 27th, 1997
+
+eMail: sysop@nostlgic.tng.oche.de

Documentation/m68k/index.rst

@@ -8,6 +8,7 @@ m68k Architecture
    :maxdepth: 2
 
    kernel-options
+   buddha-driver
 
 .. only::  subproject and html