dt-bindings: net: convert sff,sfp to dtschema
Convert the sff,sfp.txt bindings to the DT schema format. Also add the new path to the list of maintained files. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit is contained in:
Ioana Ciornei
Jakub Kicinski
Родитель
5022e221c9
Коммит
70991f1e68
|
|
@ -1,85 +0,0 @@
|
|||
Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP)
|
||||
Transceiver
|
||||
|
||||
Required properties:
|
||||
|
||||
- compatible : must be one of
|
||||
"sff,sfp" for SFP modules
|
||||
"sff,sff" for soldered down SFF modules
|
||||
|
||||
- i2c-bus : phandle of an I2C bus controller for the SFP two wire serial
|
||||
interface
|
||||
|
||||
Optional Properties:
|
||||
|
||||
- mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS)
|
||||
module presence input gpio signal, active (module absent) high. Must
|
||||
not be present for SFF modules
|
||||
|
||||
- los-gpios : GPIO phandle and a specifier of the Receiver Loss of Signal
|
||||
Indication input gpio signal, active (signal lost) high
|
||||
|
||||
- tx-fault-gpios : GPIO phandle and a specifier of the Module Transmitter
|
||||
Fault input gpio signal, active (fault condition) high
|
||||
|
||||
- tx-disable-gpios : GPIO phandle and a specifier of the Transmitter Disable
|
||||
output gpio signal, active (Tx disable) high
|
||||
|
||||
- rate-select0-gpios : GPIO phandle and a specifier of the Rx Signaling Rate
|
||||
Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx rate
|
||||
Must not be present for SFF modules
|
||||
|
||||
- rate-select1-gpios : GPIO phandle and a specifier of the Tx Signaling Rate
|
||||
Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high:
|
||||
high Tx rate. Must not be present for SFF modules
|
||||
|
||||
- maximum-power-milliwatt : Maximum module power consumption
|
||||
Specifies the maximum power consumption allowable by a module in the
|
||||
slot, in milli-Watts. Presently, modules can be up to 1W, 1.5W or 2W.
|
||||
|
||||
Example #1: Direct serdes to SFP connection
|
||||
|
||||
sfp_eth3: sfp-eth3 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&sfp_1g_i2c>;
|
||||
los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
|
||||
maximum-power-milliwatt = <1000>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
|
||||
tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
|
||||
tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
&cps_emac3 {
|
||||
phy-names = "comphy";
|
||||
phys = <&cps_comphy5 0>;
|
||||
sfp = <&sfp_eth3>;
|
||||
};
|
||||
|
||||
Example #2: Serdes to PHY to SFP connection
|
||||
|
||||
sfp_eth0: sfp-eth0 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&sfpp0_i2c>;
|
||||
los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cps_sfpp0_pins>;
|
||||
tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
|
||||
tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
p0_phy: ethernet-phy@0 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>;
|
||||
reg = <0>;
|
||||
interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>;
|
||||
sfp = <&sfp_eth0>;
|
||||
};
|
||||
|
||||
&cpm_eth0 {
|
||||
phy = <&p0_phy>;
|
||||
phy-mode = "10gbase-kr";
|
||||
};
|
||||
|
|
@ -0,0 +1,142 @@
|
|||
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
||||
%YAML 1.2
|
||||
---
|
||||
$id: "http://devicetree.org/schemas/net/sff,sfp.yaml#"
|
||||
$schema: "http://devicetree.org/meta-schemas/core.yaml#"
|
||||
|
||||
title: Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP)
|
||||
Transceiver
|
||||
|
||||
maintainers:
|
||||
- Russell King <linux@armlinux.org.uk>
|
||||
|
||||
properties:
|
||||
compatible:
|
||||
enum:
|
||||
- sff,sfp # for SFP modules
|
||||
- sff,sff # for soldered down SFF modules
|
||||
|
||||
i2c-bus:
|
||||
$ref: /schemas/types.yaml#/definitions/phandle
|
||||
description:
|
||||
phandle of an I2C bus controller for the SFP two wire serial
|
||||
|
||||
maximum-power-milliwatt:
|
||||
maxItems: 1
|
||||
description:
|
||||
Maximum module power consumption Specifies the maximum power consumption
|
||||
allowable by a module in the slot, in milli-Watts. Presently, modules can
|
||||
be up to 1W, 1.5W or 2W.
|
||||
|
||||
"mod-def0-gpios":
|
||||
maxItems: 1
|
||||
description:
|
||||
GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) module
|
||||
presence input gpio signal, active (module absent) high. Must not be
|
||||
present for SFF modules
|
||||
|
||||
"los-gpios":
|
||||
maxItems: 1
|
||||
description:
|
||||
GPIO phandle and a specifier of the Receiver Loss of Signal Indication
|
||||
input gpio signal, active (signal lost) high
|
||||
|
||||
"tx-fault-gpios":
|
||||
maxItems: 1
|
||||
description:
|
||||
GPIO phandle and a specifier of the Module Transmitter Fault input gpio
|
||||
signal, active (fault condition) high
|
||||
|
||||
"tx-disable-gpios":
|
||||
maxItems: 1
|
||||
description:
|
||||
GPIO phandle and a specifier of the Transmitter Disable output gpio
|
||||
signal, active (Tx disable) high
|
||||
|
||||
"rate-select0-gpios":
|
||||
maxItems: 1
|
||||
description:
|
||||
GPIO phandle and a specifier of the Rx Signaling Rate Select (AKA RS0)
|
||||
output gpio signal, low - low Rx rate, high - high Rx rate Must not be
|
||||
present for SFF modules
|
||||
|
||||
"rate-select1-gpios":
|
||||
maxItems: 1
|
||||
description:
|
||||
GPIO phandle and a specifier of the Tx Signaling Rate Select (AKA RS1)
|
||||
output gpio signal (SFP+ only), low - low Tx rate, high - high Tx rate. Must
|
||||
not be present for SFF modules
|
||||
|
||||
allOf:
|
||||
- if:
|
||||
properties:
|
||||
compatible:
|
||||
contains:
|
||||
const: sff,sff
|
||||
then:
|
||||
properties:
|
||||
mod-def0-gpios: false
|
||||
rate-select0-gpios: false
|
||||
rate-select1-gpios: false
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- i2c-bus
|
||||
|
||||
additionalProperties: false
|
||||
|
||||
examples:
|
||||
- | # Direct serdes to SFP connection
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
|
||||
sfp_eth3: sfp-eth3 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&sfp_1g_i2c>;
|
||||
los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
|
||||
maximum-power-milliwatt = <1000>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
|
||||
tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
|
||||
tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
cps_emac3 {
|
||||
phy-names = "comphy";
|
||||
phys = <&cps_comphy5 0>;
|
||||
sfp = <&sfp_eth3>;
|
||||
};
|
||||
|
||||
- | # Serdes to PHY to SFP connection
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
||||
|
||||
sfp_eth0: sfp-eth0 {
|
||||
compatible = "sff,sfp";
|
||||
i2c-bus = <&sfpp0_i2c>;
|
||||
los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>;
|
||||
mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cps_sfpp0_pins>;
|
||||
tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
|
||||
tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
mdio {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
p0_phy: ethernet-phy@0 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>;
|
||||
reg = <0>;
|
||||
interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>;
|
||||
sfp = <&sfp_eth0>;
|
||||
};
|
||||
};
|
||||
|
||||
cpm_eth0 {
|
||||
phy = <&p0_phy>;
|
||||
phy-mode = "10gbase-kr";
|
||||
};
|
||||
|
|
@ -18189,6 +18189,7 @@ SFF/SFP/SFP+ MODULE SUPPORT
|
|||
M: Russell King <linux@armlinux.org.uk>
|
||||
L: netdev@vger.kernel.org
|
||||
S: Maintained
|
||||
F: Documentation/devicetree/bindings/net/sff,sfp.yaml
|
||||
F: drivers/net/phy/phylink.c
|
||||
F: drivers/net/phy/sfp*
|
||||
F: include/linux/mdio/mdio-i2c.h
|
||||
|
|
|
|||
Загрузка…
Ссылка в новой задаче