Input: generic driver for rotary encoders on GPIOs
This patch adds a generic driver for rotary encoders connected to GPIO pins of a system. It relies on gpiolib and generic hardware irqs. The documentation that also comes with this patch explains the concept and how to use the driver. Signed-off-by: Daniel Mack <daniel@caiaq.de> Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This commit is contained in:
Daniel Mack
Dmitry Torokhov
Родитель
b0ecc73094
Коммит
73969ff0ed
|
|
@ -0,0 +1,101 @@
|
|||
rotary-encoder - a generic driver for GPIO connected devices
|
||||
Daniel Mack <daniel@caiaq.de>, Feb 2009
|
||||
|
||||
0. Function
|
||||
-----------
|
||||
|
||||
Rotary encoders are devices which are connected to the CPU or other
|
||||
peripherals with two wires. The outputs are phase-shifted by 90 degrees
|
||||
and by triggering on falling and rising edges, the turn direction can
|
||||
be determined.
|
||||
|
||||
The phase diagram of these two outputs look like this:
|
||||
|
||||
_____ _____ _____
|
||||
| | | | | |
|
||||
Channel A ____| |_____| |_____| |____
|
||||
|
||||
: : : : : : : : : : : :
|
||||
__ _____ _____ _____
|
||||
| | | | | | |
|
||||
Channel B |_____| |_____| |_____| |__
|
||||
|
||||
: : : : : : : : : : : :
|
||||
Event a b c d a b c d a b c d
|
||||
|
||||
|<-------->|
|
||||
one step
|
||||
|
||||
|
||||
For more information, please see
|
||||
http://en.wikipedia.org/wiki/Rotary_encoder
|
||||
|
||||
|
||||
1. Events / state machine
|
||||
-------------------------
|
||||
|
||||
a) Rising edge on channel A, channel B in low state
|
||||
This state is used to recognize a clockwise turn
|
||||
|
||||
b) Rising edge on channel B, channel A in high state
|
||||
When entering this state, the encoder is put into 'armed' state,
|
||||
meaning that there it has seen half the way of a one-step transition.
|
||||
|
||||
c) Falling edge on channel A, channel B in high state
|
||||
This state is used to recognize a counter-clockwise turn
|
||||
|
||||
d) Falling edge on channel B, channel A in low state
|
||||
Parking position. If the encoder enters this state, a full transition
|
||||
should have happend, unless it flipped back on half the way. The
|
||||
'armed' state tells us about that.
|
||||
|
||||
2. Platform requirements
|
||||
------------------------
|
||||
|
||||
As there is no hardware dependent call in this driver, the platform it is
|
||||
used with must support gpiolib. Another requirement is that IRQs must be
|
||||
able to fire on both edges.
|
||||
|
||||
|
||||
3. Board integration
|
||||
--------------------
|
||||
|
||||
To use this driver in your system, register a platform_device with the
|
||||
name 'rotary-encoder' and associate the IRQs and some specific platform
|
||||
data with it.
|
||||
|
||||
struct rotary_encoder_platform_data is declared in
|
||||
include/linux/rotary-encoder.h and needs to be filled with the number of
|
||||
steps the encoder has and can carry information about externally inverted
|
||||
signals (because of used invertig buffer or other reasons).
|
||||
|
||||
Because GPIO to IRQ mapping is platform specific, this information must
|
||||
be given in seperately to the driver. See the example below.
|
||||
|
||||
---------<snip>---------
|
||||
|
||||
/* board support file example */
|
||||
|
||||
#include <linux/input.h>
|
||||
#include <linux/rotary_encoder.h>
|
||||
|
||||
#define GPIO_ROTARY_A 1
|
||||
#define GPIO_ROTARY_B 2
|
||||
|
||||
static struct rotary_encoder_platform_data my_rotary_encoder_info = {
|
||||
.steps = 24,
|
||||
.axis = ABS_X,
|
||||
.gpio_a = GPIO_ROTARY_A,
|
||||
.gpio_b = GPIO_ROTARY_B,
|
||||
.inverted_a = 0,
|
||||
.inverted_b = 0,
|
||||
};
|
||||
|
||||
static struct platform_device rotary_encoder_device = {
|
||||
.name = "rotary-encoder",
|
||||
.id = 0,
|
||||
.dev = {
|
||||
.platform_data = &my_rotary_encoder_info,
|
||||
}
|
||||
};
|
||||
|
||||
|
|
@ -227,4 +227,15 @@ config INPUT_PCF50633_PMU
|
|||
Say Y to include support for delivering PMU events via input
|
||||
layer on NXP PCF50633.
|
||||
|
||||
config INPUT_GPIO_ROTARY_ENCODER
|
||||
tristate "Rotary encoders connected to GPIO pins"
|
||||
depends on GPIOLIB && GENERIC_GPIO
|
||||
help
|
||||
Say Y here to add support for rotary encoders connected to GPIO lines.
|
||||
Check file:Documentation/incput/rotary_encoder.txt for more
|
||||
information.
|
||||
|
||||
To compile this driver as a module, choose M here: the
|
||||
module will be called rotary_encoder.
|
||||
|
||||
endif
|
||||
|
|
|
|||
|
|
@ -22,3 +22,5 @@ obj-$(CONFIG_INPUT_UINPUT) += uinput.o
|
|||
obj-$(CONFIG_INPUT_APANEL) += apanel.o
|
||||
obj-$(CONFIG_INPUT_SGI_BTNS) += sgi_btns.o
|
||||
obj-$(CONFIG_INPUT_PCF50633_PMU) += pcf50633-input.o
|
||||
obj-$(CONFIG_INPUT_GPIO_ROTARY_ENCODER) += rotary_encoder.o
|
||||
|
||||
|
|
|
|||
|
|
@ -0,0 +1,221 @@
|
|||
/*
|
||||
* rotary_encoder.c
|
||||
*
|
||||
* (c) 2009 Daniel Mack <daniel@caiaq.de>
|
||||
*
|
||||
* state machine code inspired by code from Tim Ruetz
|
||||
*
|
||||
* A generic driver for rotary encoders connected to GPIO lines.
|
||||
* See file:Documentation/input/rotary_encoder.txt for more information
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/interrupt.h>
|
||||
#include <linux/input.h>
|
||||
#include <linux/device.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/gpio.h>
|
||||
#include <linux/rotary_encoder.h>
|
||||
|
||||
#define DRV_NAME "rotary-encoder"
|
||||
|
||||
struct rotary_encoder {
|
||||
unsigned int irq_a;
|
||||
unsigned int irq_b;
|
||||
unsigned int pos;
|
||||
unsigned int armed;
|
||||
unsigned int dir;
|
||||
struct input_dev *input;
|
||||
struct rotary_encoder_platform_data *pdata;
|
||||
};
|
||||
|
||||
static irqreturn_t rotary_encoder_irq(int irq, void *dev_id)
|
||||
{
|
||||
struct rotary_encoder *encoder = dev_id;
|
||||
struct rotary_encoder_platform_data *pdata = encoder->pdata;
|
||||
int a = !!gpio_get_value(pdata->gpio_a);
|
||||
int b = !!gpio_get_value(pdata->gpio_b);
|
||||
int state;
|
||||
|
||||
a ^= pdata->inverted_a;
|
||||
b ^= pdata->inverted_b;
|
||||
state = (a << 1) | b;
|
||||
|
||||
switch (state) {
|
||||
|
||||
case 0x0:
|
||||
if (!encoder->armed)
|
||||
break;
|
||||
|
||||
if (encoder->dir) {
|
||||
/* turning counter-clockwise */
|
||||
encoder->pos += pdata->steps;
|
||||
encoder->pos--;
|
||||
encoder->pos %= pdata->steps;
|
||||
} else {
|
||||
/* turning clockwise */
|
||||
encoder->pos++;
|
||||
encoder->pos %= pdata->steps;
|
||||
}
|
||||
|
||||
input_report_abs(encoder->input, pdata->axis, encoder->pos);
|
||||
input_sync(encoder->input);
|
||||
|
||||
encoder->armed = 0;
|
||||
break;
|
||||
|
||||
case 0x1:
|
||||
case 0x2:
|
||||
if (encoder->armed)
|
||||
encoder->dir = state - 1;
|
||||
break;
|
||||
|
||||
case 0x3:
|
||||
encoder->armed = 1;
|
||||
break;
|
||||
}
|
||||
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
static int __devinit rotary_encoder_probe(struct platform_device *pdev)
|
||||
{
|
||||
struct rotary_encoder_platform_data *pdata = pdev->dev.platform_data;
|
||||
struct rotary_encoder *encoder;
|
||||
struct input_dev *input;
|
||||
int err;
|
||||
|
||||
if (!pdata || !pdata->steps) {
|
||||
dev_err(&pdev->dev, "invalid platform data\n");
|
||||
return -ENOENT;
|
||||
}
|
||||
|
||||
encoder = kzalloc(sizeof(struct rotary_encoder), GFP_KERNEL);
|
||||
input = input_allocate_device();
|
||||
if (!encoder || !input) {
|
||||
dev_err(&pdev->dev, "failed to allocate memory for device\n");
|
||||
err = -ENOMEM;
|
||||
goto exit_free_mem;
|
||||
}
|
||||
|
||||
encoder->input = input;
|
||||
encoder->pdata = pdata;
|
||||
encoder->irq_a = gpio_to_irq(pdata->gpio_a);
|
||||
encoder->irq_b = gpio_to_irq(pdata->gpio_b);
|
||||
|
||||
/* create and register the input driver */
|
||||
input->name = pdev->name;
|
||||
input->id.bustype = BUS_HOST;
|
||||
input->dev.parent = &pdev->dev;
|
||||
input->evbit[0] = BIT_MASK(EV_ABS);
|
||||
input_set_abs_params(encoder->input,
|
||||
pdata->axis, 0, pdata->steps, 0, 1);
|
||||
|
||||
err = input_register_device(input);
|
||||
if (err) {
|
||||
dev_err(&pdev->dev, "failed to register input device\n");
|
||||
goto exit_free_mem;
|
||||
}
|
||||
|
||||
/* request the GPIOs */
|
||||
err = gpio_request(pdata->gpio_a, DRV_NAME);
|
||||
if (err) {
|
||||
dev_err(&pdev->dev, "unable to request GPIO %d\n",
|
||||
pdata->gpio_a);
|
||||
goto exit_unregister_input;
|
||||
}
|
||||
|
||||
err = gpio_request(pdata->gpio_b, DRV_NAME);
|
||||
if (err) {
|
||||
dev_err(&pdev->dev, "unable to request GPIO %d\n",
|
||||
pdata->gpio_b);
|
||||
goto exit_free_gpio_a;
|
||||
}
|
||||
|
||||
/* request the IRQs */
|
||||
err = request_irq(encoder->irq_a, &rotary_encoder_irq,
|
||||
IORESOURCE_IRQ_HIGHEDGE | IORESOURCE_IRQ_LOWEDGE,
|
||||
DRV_NAME, encoder);
|
||||
if (err) {
|
||||
dev_err(&pdev->dev, "unable to request IRQ %d\n",
|
||||
encoder->irq_a);
|
||||
goto exit_free_gpio_b;
|
||||
}
|
||||
|
||||
err = request_irq(encoder->irq_b, &rotary_encoder_irq,
|
||||
IORESOURCE_IRQ_HIGHEDGE | IORESOURCE_IRQ_LOWEDGE,
|
||||
DRV_NAME, encoder);
|
||||
if (err) {
|
||||
dev_err(&pdev->dev, "unable to request IRQ %d\n",
|
||||
encoder->irq_b);
|
||||
goto exit_free_irq_a;
|
||||
}
|
||||
|
||||
platform_set_drvdata(pdev, encoder);
|
||||
|
||||
return 0;
|
||||
|
||||
exit_free_irq_a:
|
||||
free_irq(encoder->irq_a, encoder);
|
||||
exit_free_gpio_b:
|
||||
gpio_free(pdata->gpio_b);
|
||||
exit_free_gpio_a:
|
||||
gpio_free(pdata->gpio_a);
|
||||
exit_unregister_input:
|
||||
input_unregister_device(input);
|
||||
input = NULL; /* so we don't try to free it */
|
||||
exit_free_mem:
|
||||
input_free_device(input);
|
||||
kfree(encoder);
|
||||
return err;
|
||||
}
|
||||
|
||||
static int __devexit rotary_encoder_remove(struct platform_device *pdev)
|
||||
{
|
||||
struct rotary_encoder *encoder = platform_get_drvdata(pdev);
|
||||
struct rotary_encoder_platform_data *pdata = pdev->dev.platform_data;
|
||||
|
||||
free_irq(encoder->irq_a, encoder);
|
||||
free_irq(encoder->irq_b, encoder);
|
||||
gpio_free(pdata->gpio_a);
|
||||
gpio_free(pdata->gpio_b);
|
||||
input_unregister_device(encoder->input);
|
||||
platform_set_drvdata(pdev, NULL);
|
||||
kfree(encoder);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static struct platform_driver rotary_encoder_driver = {
|
||||
.probe = rotary_encoder_probe,
|
||||
.remove = __devexit_p(rotary_encoder_remove),
|
||||
.driver = {
|
||||
.name = DRV_NAME,
|
||||
.owner = THIS_MODULE,
|
||||
}
|
||||
};
|
||||
|
||||
static int __init rotary_encoder_init(void)
|
||||
{
|
||||
return platform_driver_register(&rotary_encoder_driver);
|
||||
}
|
||||
|
||||
static void __exit rotary_encoder_exit(void)
|
||||
{
|
||||
platform_driver_unregister(&rotary_encoder_driver);
|
||||
}
|
||||
|
||||
module_init(rotary_encoder_init);
|
||||
module_exit(rotary_encoder_exit);
|
||||
|
||||
MODULE_ALIAS("platform:" DRV_NAME);
|
||||
MODULE_DESCRIPTION("GPIO rotary encoder driver");
|
||||
MODULE_AUTHOR("Daniel Mack <daniel@caiaq.de>");
|
||||
MODULE_LICENSE("GPL v2");
|
||||
|
||||
|
|
@ -0,0 +1,13 @@
|
|||
#ifndef __ROTARY_ENCODER_H__
|
||||
#define __ROTARY_ENCODER_H__
|
||||
|
||||
struct rotary_encoder_platform_data {
|
||||
unsigned int steps;
|
||||
unsigned int axis;
|
||||
unsigned int gpio_a;
|
||||
unsigned int gpio_b;
|
||||
unsigned int inverted_a;
|
||||
unsigned int inverted_b;
|
||||
};
|
||||
|
||||
#endif /* __ROTARY_ENCODER_H__ */
|
||||
Загрузка…
Ссылка в новой задаче