ARM: SoC fixes for v5.11, part 2

These are the current arm-soc bug fixes for linux-5.11. I already merged
 a larger set that just came in during the past three days but has not
 had much exposure in linux-next, so these are the ones I merged last week.
 
 Most of these are for the NXP i.MX platform (descriptions from their
 pull request):
 
  - Fix pcf2127 reset for imx7d-flex-concentrator board.
  - Fix i.MX6 suspend with Thumb-2 kernel.
  - Fix ethernet-phy address issue on imx6qdl-sr-som board.
  - Fix GPIO3 `gpio-ranges` on i.MX8MP.
  - Select SOC_BUS for IMX_SCU driver to fix build issue.
  - Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
    #pwm-cells conversion.
  - Fix duplicated bus node name for i.MX8MN SoC.
  - Fix reset register offset on LS1028A SoC.
  - Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
    index consistent with previous kernel version.
  - Selecting ARM_GIC_V3 on non-CP15 processors to fix one build failure
    with i.MX8M SoC driver.
  - Fix typos with status property on imx6qdl-kontron-samx6i board.
  - Fix duplicated regulator-name on imx6qdl-gw52xx board.
 
 Aside from i.MX, the bugfixes are all over the place:
 
  - Coccinelle found a refcount imbalance on integrator
  - defconfig fix for TI K3
  - A boot regression fix for ST ux500
  - A code preemption fix for the optee driver
  - USB DMA regression on Broadcom Stingray
  - A bogus boot time warning fix for at91 code
 
 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmAS0A0ACgkQmmx57+YA
 GNmk7w/9GCdeyLysp1ZdYdTlysfuqh2wR31/9t3rIv6E+xDH/m9yYVRWKqVMqN00
 FtgYABfjsobOLdaiO/Bpl6bK6B5WXmLrmBXptgSXJCjV147r/orlIH3BCtqBR1ez
 3anH0zqwklOHtTMDfz012VsdNSk81yqEnl4kFYcLDOJ6wtg4cl8ks4GIkYopT4XX
 Yov+iUKO2xzTdl7XSBgqNjNUntZcLndffnuu+tdb4Ehz6H6qeODW2BMCZJNvd0BB
 h8bFiYo6fNkywFDevO7Tbyufzkuz7CNH2EiOL5zzfbOxBZ3fyOf0zBfFe+ldlcYq
 2qYid7rpLPF4Hn4HzTiwh2jPj4jef3F0XpBq8YrUJK5p7BoOp9QkMNqoJfpidWoa
 ROkgbPPaiVanOiTpDA6++IOxjGP+0I01LXhiP5SwfN6ua4UYinS9f2MgoPgT70mT
 Doq9EIucORBi0ZbzUzl5EESCya4ByRTu7EYrENeWy3Y9HsGZ921l/vmIsAHWo9P9
 8pEgm9ttPErZlpmABPiEkJcF8IsxaLtcQuSFpLsFUweIDi65mMkF5fXQ+K3OicdT
 mMAu9EaNEUBUwWRK2Cq9xIV/8/DwFHVSg40FqatDgvhihtZZA6GgoSDZvGJO34oo
 NjqLxgqFVMq6HDFC36+Rn1/iP6mpQsvgobs+Qaa357wFT/DUqCg=
 =Vneq
 -----END PGP SIGNATURE-----

Merge tag 'arm-soc-fixes-v5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
 "These are the current arm-soc bug fixes for linux-5.11. I already
  merged a larger set that just came in during the past three days but
  has not had much exposure in linux-next, but this is the subset I
  merged last week.

  Most of these are for the NXP i.MX platform (descriptions from their
  pull request):

   - Fix pcf2127 reset for imx7d-flex-concentrator board.
   - Fix i.MX6 suspend with Thumb-2 kernel.
   - Fix ethernet-phy address issue on imx6qdl-sr-som board.
   - Fix GPIO3 `gpio-ranges` on i.MX8MP.
   - Select SOC_BUS for IMX_SCU driver to fix build issue.
   - Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
     #pwm-cells conversion.
   - Fix duplicated bus node name for i.MX8MN SoC.
   - Fix reset register offset on LS1028A SoC.
   - Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
     index consistent with previous kernel version.
   - Selecting ARM_GIC_V3 on non-CP15 processors to fix one build
     failure with i.MX8M SoC driver.
   - Fix typos with status property on imx6qdl-kontron-samx6i board.
   - Fix duplicated regulator-name on imx6qdl-gw52xx board.

  Aside from i.MX, the bugfixes are all over the place:

   - Coccinelle found a refcount imbalance on integrator
   - defconfig fix for TI K3
   - A boot regression fix for ST ux500
   - A code preemption fix for the optee driver
   - USB DMA regression on Broadcom Stingray
   - A bogus boot time warning fix for at91 code"

* tag 'arm-soc-fixes-v5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  MAINTAINERS: Include bcm2835 subsequents into search
  arm64: dts: broadcom: Fix USB DMA address translation for Stingray
  drivers: soc: atmel: add null entry at the end of at91_soc_allowed_list[]
  drivers: soc: atmel: Avoid calling at91_soc_init on non AT91 SoCs
  tee: optee: replace might_sleep with cond_resched
  firmware: imx: select SOC_BUS to fix firmware build
  arm64: dts: imx8mp: Correct the gpio ranges of gpio3
  ARM: dts: imx6qdl-sr-som: fix some cubox-i platforms
  ARM: imx: build suspend-imx6.S with arm instruction set
  ARM: dts: imx7d-flex-concentrator: fix pcf2127 reset
  ARM: dts: ux500: Reserve memory carveouts
  arm64: defconfig: Drop unused K3 SoC specific options
  bus: arm-integrator-lm: Add of_node_put() before return statement
  ARM: dts: imx6qdl-gw52xx: fix duplicate regulator naming
  ARM: dts: imx6qdl-kontron-samx6i: fix i2c_lcd/cam default status
  ARM: imx: fix imx8m dependencies
  ARM: dts: tbs2910: rename MMC node aliases
  arm64: dts: ls1028a: fix the offset of the reset register
  arm64: dts: imx8mn: Fix duplicate node name
  ARM: dts: imx6qdl-kontron-samx6i: fix pwms for lcd-backlight

MAINTAINERS

@@ -3411,7 +3411,7 @@ F:	Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
 F:	drivers/pci/controller/pcie-brcmstb.c
 F:	drivers/staging/vc04_services
 N:	bcm2711
-N:	bcm2835
+N:	bcm283*
 
 BROADCOM BCM281XX/BCM11XXX/BCM216XX ARM ARCHITECTURE
 M:	Florian Fainelli <f.fainelli@gmail.com>

arch/arm/boot/dts/imx6q-tbs2910.dts

@@ -16,6 +16,13 @@
 		stdout-path = &uart1;
 	};
 
+	aliases {
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc3;
+		mmc2 = &usdhc4;
+		/delete-property/ mmc3;
+	};
+
 	memory@10000000 {
 		device_type = "memory";
 		reg = <0x10000000 0x80000000>;

arch/arm/boot/dts/imx6qdl-gw52xx.dtsi

@@ -418,7 +418,7 @@
 
 			/* VDD_AUD_1P8: Audio codec */
 			reg_aud_1p8v: ldo3 {
-				regulator-name = "vdd1p8";
+				regulator-name = "vdd1p8a";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;

arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi

@@ -137,7 +137,7 @@
 
 	lcd_backlight: lcd-backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		pwm-names = "LCD_BKLT_PWM";
 
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
@@ -167,7 +167,7 @@
 		i2c-gpio,delay-us = <2>; /* ~100 kHz */
 		#address-cells = <1>;
 		#size-cells = <0>;
-		status = "disabld";
+		status = "disabled";
 	};
 
 	i2c_cam: i2c-gpio-cam {
@@ -179,7 +179,7 @@
 		i2c-gpio,delay-us = <2>; /* ~100 kHz */
 		#address-cells = <1>;
 		#size-cells = <0>;
-		status = "disabld";
+		status = "disabled";
 	};
 };
 

arch/arm/boot/dts/imx6qdl-sr-som.dtsi

@@ -53,7 +53,6 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
-	phy-handle = <&phy>;
 	phy-mode = "rgmii-id";
 	phy-reset-duration = <2>;
 	phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
@@ -63,10 +62,19 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		phy: ethernet-phy@0 {
+		/*
+		 * The PHY can appear at either address 0 or 4 due to the
+		 * configuration (LED) pin not being pulled sufficiently.
+		 */
+		ethernet-phy@0 {
 			reg = <0>;
 			qca,clk-out-frequency = <125000000>;
 		};
+
+		ethernet-phy@4 {
+			reg = <4>;
+			qca,clk-out-frequency = <125000000>;
+		};
 	};
 };
 

arch/arm/boot/dts/imx7d-flex-concentrator.dts

@@ -115,6 +115,7 @@
 		compatible = "nxp,pcf2127";
 		reg = <0>;
 		spi-max-frequency = <2000000>;
+		reset-source;
 	};
 };
 

arch/arm/boot/dts/ste-db8500.dtsi

@@ -12,4 +12,42 @@
 					    200000 0>;
 		};
 	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/* Modem trace memory */
+		ram@06000000 {
+			reg = <0x06000000 0x00f00000>;
+			no-map;
+		};
+
+		/* Modem shared memory */
+		ram@06f00000 {
+			reg = <0x06f00000 0x00100000>;
+			no-map;
+		};
+
+		/* Modem private memory */
+		ram@07000000 {
+			reg = <0x07000000 0x01000000>;
+			no-map;
+		};
+
+		/*
+		 * Initial Secure Software ISSW memory
+		 *
+		 * This is probably only used if the kernel tries
+		 * to actually call into trustzone to run secure
+		 * applications, which the mainline kernel probably
+		 * will not do on this old chipset. But you can never
+		 * be too careful, so reserve this memory anyway.
+		 */
+		ram@17f00000 {
+			reg = <0x17f00000 0x00100000>;
+			no-map;
+		};
+	};
 };

arch/arm/boot/dts/ste-db8520.dtsi

@@ -12,4 +12,42 @@
 					    200000 0>;
 		};
 	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/* Modem trace memory */
+		ram@06000000 {
+			reg = <0x06000000 0x00f00000>;
+			no-map;
+		};
+
+		/* Modem shared memory */
+		ram@06f00000 {
+			reg = <0x06f00000 0x00100000>;
+			no-map;
+		};
+
+		/* Modem private memory */
+		ram@07000000 {
+			reg = <0x07000000 0x01000000>;
+			no-map;
+		};
+
+		/*
+		 * Initial Secure Software ISSW memory
+		 *
+		 * This is probably only used if the kernel tries
+		 * to actually call into trustzone to run secure
+		 * applications, which the mainline kernel probably
+		 * will not do on this old chipset. But you can never
+		 * be too careful, so reserve this memory anyway.
+		 */
+		ram@17f00000 {
+			reg = <0x17f00000 0x00100000>;
+			no-map;
+		};
+	};
 };

arch/arm/boot/dts/ste-db9500.dtsi

@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "ste-dbx5x0.dtsi"
+
+/ {
+	cpus {
+		cpu@300 {
+			/* cpufreq controls */
+			operating-points = <1152000 0
+					    800000 0
+					    400000 0
+					    200000 0>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/*
+		 * Initial Secure Software ISSW memory
+		 *
+		 * This is probably only used if the kernel tries
+		 * to actually call into trustzone to run secure
+		 * applications, which the mainline kernel probably
+		 * will not do on this old chipset. But you can never
+		 * be too careful, so reserve this memory anyway.
+		 */
+		ram@17f00000 {
+			reg = <0x17f00000 0x00100000>;
+			no-map;
+		};
+	};
+};

arch/arm/boot/dts/ste-snowball.dts

@@ -4,7 +4,7 @@
  */
 
 /dts-v1/;
-#include "ste-db8500.dtsi"
+#include "ste-db9500.dtsi"
 #include "ste-href-ab8500.dtsi"
 #include "ste-href-family-pinctrl.dtsi"
 

arch/arm/mach-imx/suspend-imx6.S

@@ -67,6 +67,7 @@
 #define MX6Q_CCM_CCR	0x0
 
 	.align 3
+	.arm
 
 	.macro  sync_l2_cache
 

arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi

@@ -4,11 +4,16 @@
  */
 	usb {
 		compatible = "simple-bus";
-		dma-ranges;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges = <0x0 0x0 0x0 0x68500000 0x0 0x00400000>;
 
+		/*
+		 * Internally, USB bus to the interconnect can only address up
+		 * to 40-bit
+		 */
+		dma-ranges = <0 0 0 0 0x100 0x0>;
+
 		usbphy0: usb-phy@0 {
 			compatible = "brcm,sr-usb-combo-phy";
 			reg = <0x0 0x00000000 0x0 0x100>;

arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi

@@ -101,7 +101,7 @@
 	reboot {
 		compatible ="syscon-reboot";
 		regmap = <&rst>;
-		offset = <0xb0>;
+		offset = <0>;
 		mask = <0x02>;
 	};
 

arch/arm64/boot/dts/freescale/imx8mn.dtsi

@@ -253,7 +253,7 @@
 			#size-cells = <1>;
 			ranges;
 
-			spba: bus@30000000 {
+			spba: spba-bus@30000000 {
 				compatible = "fsl,spba-bus", "simple-bus";
 				#address-cells = <1>;
 				#size-cells = <1>;

arch/arm64/boot/dts/freescale/imx8mp.dtsi

@@ -266,7 +266,7 @@
 				#gpio-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
-				gpio-ranges = <&iomuxc 0 56 26>, <&iomuxc 0 144 4>;
+				gpio-ranges = <&iomuxc 0 56 26>, <&iomuxc 26 144 4>;
 			};
 
 			gpio4: gpio@30230000 {

arch/arm64/configs/defconfig

@@ -991,8 +991,6 @@ CONFIG_ARCH_TEGRA_210_SOC=y
 CONFIG_ARCH_TEGRA_186_SOC=y
 CONFIG_ARCH_TEGRA_194_SOC=y
 CONFIG_ARCH_TEGRA_234_SOC=y
-CONFIG_ARCH_K3_AM6_SOC=y
-CONFIG_ARCH_K3_J721E_SOC=y
 CONFIG_TI_SCI_PM_DOMAINS=y
 CONFIG_EXTCON_PTN5150=m
 CONFIG_EXTCON_USB_GPIO=y

drivers/bus/arm-integrator-lm.c

@@ -54,6 +54,7 @@ static int integrator_lm_populate(int num, struct device *dev)
 			ret = of_platform_default_populate(child, NULL, dev);
 			if (ret) {
 				dev_err(dev, "failed to populate module\n");
+				of_node_put(child);
 				return ret;
 			}
 		}

drivers/firmware/imx/Kconfig

@@ -13,6 +13,7 @@ config IMX_DSP
 config IMX_SCU
 	bool "IMX SCU Protocol driver"
 	depends on IMX_MBOX
+	select SOC_BUS
 	help
 	  The System Controller Firmware (SCFW) is a low-level system function
 	  which runs on a dedicated Cortex-M core to provide power, clock, and

drivers/soc/atmel/soc.c

@@ -271,8 +271,21 @@ struct soc_device * __init at91_soc_init(const struct at91_soc *socs)
 	return soc_dev;
 }
 
+static const struct of_device_id at91_soc_allowed_list[] __initconst = {
+	{ .compatible = "atmel,at91rm9200", },
+	{ .compatible = "atmel,at91sam9", },
+	{ .compatible = "atmel,sama5", },
+	{ .compatible = "atmel,samv7", },
+	{ }
+};
+
 static int __init atmel_soc_device_init(void)
 {
+	struct device_node *np = of_find_node_by_path("/");
+
+	if (!of_match_node(at91_soc_allowed_list, np))
+		return 0;
+
 	at91_soc_init(socs);
 
 	return 0;

drivers/soc/imx/Kconfig

@@ -13,7 +13,7 @@ config SOC_IMX8M
 	depends on ARCH_MXC || COMPILE_TEST
 	default ARCH_MXC && ARM64
 	select SOC_BUS
-	select ARM_GIC_V3 if ARCH_MXC
+	select ARM_GIC_V3 if ARCH_MXC && ARCH_MULTI_V7
 	help
 	  If you say yes here you get support for the NXP i.MX8M family
 	  support, it will provide the SoC info like SoC family,

drivers/tee/optee/call.c

@@ -7,6 +7,7 @@
 #include <linux/err.h>
 #include <linux/errno.h>
 #include <linux/mm.h>
+#include <linux/sched.h>
 #include <linux/slab.h>
 #include <linux/tee_drv.h>
 #include <linux/types.h>
@@ -148,7 +149,8 @@ u32 optee_do_call_with_arg(struct tee_context *ctx, phys_addr_t parg)
 			 */
 			optee_cq_wait_for_completion(&optee->call_queue, &w);
 		} else if (OPTEE_SMC_RETURN_IS_RPC(res.a0)) {
-			might_sleep();
+			if (need_resched())
+				cond_resched();
 			param.a0 = res.a0;
 			param.a1 = res.a1;
 			param.a2 = res.a2;