ARM: dts: ux500: Add a device tree for Janice
This adds a basic device tree for the Samsung GT-I9070 mobile phone also known as Janice. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit is contained in:
Linus Walleij
Родитель
5c8fe583cc
Коммит
78894adedd
|
|
@ -1278,6 +1278,7 @@ dtb-$(CONFIG_ARCH_U8500) += \
|
|||
ste-hrefv60plus-tvk.dtb \
|
||||
ste-href520-tvk.dtb \
|
||||
ste-ux500-samsung-golden.dtb \
|
||||
ste-ux500-samsung-janice.dtb \
|
||||
ste-ux500-samsung-skomer.dtb
|
||||
dtb-$(CONFIG_ARCH_UNIPHIER) += \
|
||||
uniphier-ld4-ref.dtb \
|
||||
|
|
|
|||
|
|
@ -0,0 +1,894 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-only
|
||||
/*
|
||||
* Devicetree for the Samsung Galaxy S Advance GT-I9070 also known as Janice.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
#include "ste-db8500.dtsi"
|
||||
#include "ste-ab8500.dtsi"
|
||||
#include "ste-dbx5x0-pinctrl.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
|
||||
/ {
|
||||
model = "Samsung Galaxy S Advance (GT-I9070)";
|
||||
compatible = "samsung,janice", "st-ericsson,u8500";
|
||||
|
||||
chosen {
|
||||
stdout-path = &serial2;
|
||||
};
|
||||
|
||||
/* External LDO for eMMC LDO VMEM_3V3 controlled by GPIO6 */
|
||||
ldo_3v3_reg: regulator-gpio-ldo-3v3 {
|
||||
compatible = "regulator-fixed";
|
||||
/* Supplied in turn by VBAT */
|
||||
regulator-name = "VMEM_3V3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
|
||||
startup-delay-us = <5000>; // FIXME
|
||||
enable-active-high;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&emmc_ldo_en_default_mode>;
|
||||
};
|
||||
|
||||
/*
|
||||
* External Ricoh "TSP" regulator for the touchscreen.
|
||||
* One GPIO line controls two voltages of 3.3V and 1.8V
|
||||
* this line is known as "TSP_LDO_ON1" in the schematics.
|
||||
*/
|
||||
ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 {
|
||||
compatible = "regulator-fixed";
|
||||
/* Supplied in turn by VBAT */
|
||||
regulator-name = "LDO_TSP_A3V3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
/* GPIO94 controls this regulator */
|
||||
gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
|
||||
/* 70 ms power-on delay */
|
||||
startup-delay-us = <70000>;
|
||||
enable-active-high;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&tsp_ldo_en_default_mode>;
|
||||
};
|
||||
ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 {
|
||||
compatible = "regulator-fixed";
|
||||
/* Supplied in turn by VBAT */
|
||||
regulator-name = "VREG_TSP_1V8";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
/* GPIO94 controls this regulator */
|
||||
gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
|
||||
/* 70 ms power-on delay */
|
||||
startup-delay-us = <70000>;
|
||||
enable-active-high;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&tsp_ldo_en_default_mode>;
|
||||
};
|
||||
|
||||
/*
|
||||
* External Ricoh "TSP" regulator for the touchkeys.
|
||||
* Two GPIO lines controls two voltages of 3.3V and 1.8V
|
||||
* TSP_LDO_ON2 controls VREG_TOUCHKEY_1V8
|
||||
* EN_LED_LDO controls VREG_KLED_3V3 (key LED)
|
||||
*/
|
||||
ldo_kled_3v3_reg: regulator-gpio-vreg-kled-3v3 {
|
||||
compatible = "regulator-fixed";
|
||||
/* Supplied in turn by VBAT */
|
||||
regulator-name = "VREG_KLED_3V3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
/* GPIO68 controls this regulator */
|
||||
gpio = <&gpio2 4 GPIO_ACTIVE_HIGH>;
|
||||
/* 70 ms power-on delay */
|
||||
startup-delay-us = <70000>;
|
||||
enable-active-high;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&en_led_ldo_default_mode>;
|
||||
};
|
||||
ldo_touchkey_1v8_reg: regulator-gpio-vreg-touchkey-1v8 {
|
||||
compatible = "regulator-fixed";
|
||||
/* Supplied in turn by VBAT */
|
||||
regulator-name = "VREG_TOUCHKEY_1V8";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
/* GPIO89 controls this regulator */
|
||||
gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
|
||||
/* 70 ms power-on delay */
|
||||
startup-delay-us = <70000>;
|
||||
enable-active-high;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&tsp_ldo_on2_default_mode>;
|
||||
};
|
||||
|
||||
|
||||
/*
|
||||
* External Ricoh RP152L010B-TR LCD LDO regulator for the display.
|
||||
* LCD_PWR_EN controls a 3.0V and 1.8V output.
|
||||
*/
|
||||
lcd_3v0_reg: regulator-gpio-lcd-3v0 {
|
||||
compatible = "regulator-fixed";
|
||||
/* Supplied in turn by VBAT */
|
||||
regulator-name = "VREG_LCD_3V0";
|
||||
regulator-min-microvolt = <3000000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
/* GPIO219 controls this regulator */
|
||||
gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&lcd_pwr_en_default_mode>;
|
||||
};
|
||||
lcd_1v8_reg: regulator-gpio-lcd-1v8 {
|
||||
compatible = "regulator-fixed";
|
||||
/* Supplied in turn by VBAT */
|
||||
regulator-name = "VREG_LCD_1V8";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
/* GPIO219 controls this regulator */
|
||||
gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&lcd_pwr_en_default_mode>;
|
||||
};
|
||||
|
||||
/*
|
||||
* This regulator is a GPIO line that drives the Broadcom WLAN
|
||||
* line BT_VREG_EN high and enables the internal regulators
|
||||
* inside the chip.
|
||||
*
|
||||
* The voltage specified here is only used to determine the OCR mask,
|
||||
* the for the SDIO connector, the chip is actually connected
|
||||
* directly to VBAT.
|
||||
*/
|
||||
wl_bt_reg: regulator-gpio-wlan {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "BT_VREG_EN";
|
||||
regulator-min-microvolt = <3000000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
startup-delay-us = <100000>;
|
||||
/* GPIO222 (BT_VREG_EN) */
|
||||
gpio = <&gpio6 30 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wlan_ldo_en_default>;
|
||||
};
|
||||
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&gpio_keys_default_mode>;
|
||||
|
||||
button-home {
|
||||
linux,code = <KEY_HOME>;
|
||||
label = "HOME";
|
||||
/* GPIO91 */
|
||||
gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
button-volup {
|
||||
linux,code = <KEY_VOLUMEUP>;
|
||||
label = "VOL+";
|
||||
/* GPIO67 */
|
||||
gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
button-voldown {
|
||||
linux,code = <KEY_VOLUMEDOWN>;
|
||||
label = "VOL-";
|
||||
/* GPIO92 */
|
||||
gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
|
||||
i2c-gpio-0 {
|
||||
compatible = "i2c-gpio";
|
||||
sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c_gpio_0_default>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
/* Yamaha YAS530 magnetometer */
|
||||
magnetometer@2e {
|
||||
compatible = "yamaha,yas530";
|
||||
reg = <0x2e>;
|
||||
/* VDD 3V */
|
||||
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
||||
/* IOVDD 1.8V */
|
||||
iovdd-supply = <&ab8500_ldo_aux2_reg>;
|
||||
/* GPIO204 COMPASS_RST_N */
|
||||
reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&yas529_default>;
|
||||
};
|
||||
/* TODO: this should also be used by the NCP6914 Camera power management unit */
|
||||
};
|
||||
|
||||
/*
|
||||
* These pins do have an spi controller, however the controller on
|
||||
* these pins is not the fully featured PL022 SSP/SPI block but the
|
||||
* ST Micro diet "PL023" version. One of the lacking features in
|
||||
* this derivative is 3wire support, so it cannot be used to drive
|
||||
* this panel interface. We have to use GPIO bit-banging instead.
|
||||
*/
|
||||
spi-gpio-0 {
|
||||
compatible = "spi-gpio";
|
||||
/* Clock on GPIO220 */
|
||||
sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
|
||||
/* MISO/MOSI on GPIO224 (no separate MISO pin) */
|
||||
mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
|
||||
/* Chip select on GPIO223 */
|
||||
cs-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
|
||||
num-chipselects = <1>;
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi_gpio_0_default>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
panel@0 {
|
||||
compatible = "samsung,s6e63m0";
|
||||
reg = <0>;
|
||||
vdd3-supply = <&lcd_3v0_reg>;
|
||||
vci-supply = <&lcd_1v8_reg>;
|
||||
/* Reset on GPIO139 */
|
||||
reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&panel_default_mode>;
|
||||
spi-3wire;
|
||||
|
||||
port {
|
||||
panel_in: endpoint {
|
||||
remote-endpoint = <&display_out>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
/*
|
||||
* Current sense amplifier on the light sensor to convert current to
|
||||
* voltage. We do not know if this is the actual configuration. The
|
||||
* sense resistor value was found by calibrating in a room ambient
|
||||
* light with a second mobile phone light sensor as reference. If you
|
||||
* pry a Janice phone apart and inspect it you may figure this out.
|
||||
*/
|
||||
gp2a_shunt: current-sense-shunt {
|
||||
compatible = "current-sense-shunt";
|
||||
io-channels = <&gpadc 0x07>;
|
||||
shunt-resistor-micro-ohms = <15000000>; /* 15 ohms c:a */
|
||||
#io-channel-cells = <0>;
|
||||
io-channel-ranges;
|
||||
};
|
||||
|
||||
/* Bit-banged I2C on GPIO196 and GPIO197 also called "TOUCHKEY_I2C" */
|
||||
i2c-gpio-1 {
|
||||
compatible = "i2c-gpio";
|
||||
sda-gpios = <&gpio6 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio6 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
clock-frequency = <400000>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c_gpio_1_default>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
touchkey@20 {
|
||||
compatible = "coreriver,tc360-touchkey";
|
||||
reg = <0x20>;
|
||||
vdd-supply = <&ldo_kled_3v3_reg>;
|
||||
vcc-supply = <&ldo_touchkey_1v8_reg>;
|
||||
vddio-supply = <&ldo_touchkey_1v8_reg>;
|
||||
|
||||
/* Interrupt on GPIO 198 */
|
||||
interrupt-parent = <&gpio6>;
|
||||
interrupts = <6 IRQ_TYPE_EDGE_RISING>;
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&touchkey_default_mode>;
|
||||
linux,keycodes = <KEY_MENU KEY_BACK>;
|
||||
};
|
||||
};
|
||||
|
||||
/* Bit-banged I2C on GPIO201 and GPIO202 also called "MOT_I2C" */
|
||||
i2c-gpio-2 {
|
||||
compatible = "i2c-gpio";
|
||||
sda-gpios = <&gpio6 10 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio6 9 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c_gpio_2_default>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
/* TODO: add the Immersion ISA1200 I2C device here */
|
||||
};
|
||||
|
||||
/* Bit-banged I2C on GPIO151 and GPIO152 also called "NFC_I2C" */
|
||||
i2c-gpio-3 {
|
||||
compatible = "i2c-gpio";
|
||||
sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c_gpio_3_default>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
nfc@30 {
|
||||
compatible = "nxp,pn547", "nxp,nxp-nci-i2c";
|
||||
reg = <0x30>;
|
||||
/* NFC IRQ on GPIO32 */
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
|
||||
/* GPIO 31 */
|
||||
firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
|
||||
/* GPIO88 */
|
||||
enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pn547_janice_default>;
|
||||
};
|
||||
};
|
||||
|
||||
soc {
|
||||
/* External Micro SD slot */
|
||||
sdi0_per1@80126000 {
|
||||
arm,primecell-periphid = <0x10480180>;
|
||||
max-frequency = <50000000>;
|
||||
bus-width = <4>;
|
||||
cap-sd-highspeed;
|
||||
cap-mmc-highspeed;
|
||||
st,sig-dir-cmd;
|
||||
st,sig-dir-dat0;
|
||||
st,sig-dir-dat2;
|
||||
st,sig-pin-fbclk;
|
||||
full-pwr-cycle;
|
||||
/* MMC is powered by AUX3 1.2V .. 2.91V */
|
||||
vmmc-supply = <&ab8500_ldo_aux3_reg>;
|
||||
/* 2.9 V level translator is using AUX3 at 2.9 V as well */
|
||||
vqmmc-supply = <&ab8500_ldo_aux3_reg>;
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&mc0_a_2_default>;
|
||||
pinctrl-1 = <&mc0_a_2_sleep>;
|
||||
cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* WLAN SDIO channel */
|
||||
sdi1_per2@80118000 {
|
||||
arm,primecell-periphid = <0x10480180>;
|
||||
max-frequency = <50000000>;
|
||||
bus-width = <4>;
|
||||
non-removable;
|
||||
cap-sd-highspeed;
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&mc1_a_2_default>;
|
||||
pinctrl-1 = <&mc1_a_2_sleep>;
|
||||
/*
|
||||
* GPIO-controlled voltage enablement: this drives
|
||||
* the BT_VREG_EN line high when we use this device.
|
||||
* Represented as regulator to fill OCR mask and to
|
||||
* be usable in parallel with the Bluetooth chip.
|
||||
*/
|
||||
vmmc-supply = <&wl_bt_reg>;
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
wifi@1 {
|
||||
/* Actually BRCM4330 */
|
||||
compatible = "brcm,bcm4329-fmac";
|
||||
reg = <1>;
|
||||
/* GPIO216 WL_HOST_WAKE */
|
||||
interrupt-parent = <&gpio6>;
|
||||
interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupt-names = "host-wake";
|
||||
/* GPIO215 WLAN_RST_N */
|
||||
/* FIXME: kernel does not use this assert/deassert */
|
||||
reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wlan_default_mode>;
|
||||
};
|
||||
};
|
||||
|
||||
/* eMMC */
|
||||
sdi2_per3@80005000 {
|
||||
arm,primecell-periphid = <0x10480180>;
|
||||
max-frequency = <50000000>;
|
||||
bus-width = <8>;
|
||||
non-removable;
|
||||
cap-mmc-highspeed;
|
||||
mmc-ddr-1_8v;
|
||||
vmmc-supply = <&ldo_3v3_reg>;
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&mc2_a_1_default>;
|
||||
pinctrl-1 = <&mc2_a_1_sleep>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* GBF (Bluetooth) UART */
|
||||
uart@80120000 {
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&u0_a_1_default>;
|
||||
pinctrl-1 = <&u0_a_1_sleep>;
|
||||
status = "okay";
|
||||
|
||||
bluetooth {
|
||||
compatible = "brcm,bcm4330-bt";
|
||||
/*
|
||||
* We actually have shutdown-gpios, BT_VREG_EN on GPIO222,
|
||||
* but since this GPIO is shared with the WLAN chip, we need
|
||||
* to reference the regulator instead. The regulator
|
||||
* framework will reference count the GPIO usage and
|
||||
* make sure we can use the same GPIO for several supplies.
|
||||
*/
|
||||
// shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
|
||||
vbat-supply = <&wl_bt_reg>;
|
||||
/* BT_WAKE on GPIO199 */
|
||||
device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
|
||||
/* BT_HOST_WAKE on GPIO97 */
|
||||
/* FIXME: convert to interrupt */
|
||||
host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
|
||||
/* BT_RST_N on GPIO209 */
|
||||
reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&bluetooth_default_mode>;
|
||||
};
|
||||
};
|
||||
|
||||
/* GPS UART */
|
||||
uart@80121000 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default", "sleep";
|
||||
/* CTS/RTS is not used, CTS is repurposed as GPIO */
|
||||
pinctrl-0 = <&u1rxtx_a_1_default>;
|
||||
pinctrl-1 = <&u1rxtx_a_1_sleep>;
|
||||
/* FIXME: add a device for the GPS here */
|
||||
};
|
||||
|
||||
/* Debugging console UART connected to TSU6111RSVR (FSA880) */
|
||||
uart@80007000 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&u2rxtx_c_1_default>;
|
||||
pinctrl-1 = <&u2rxtx_c_1_sleep>;
|
||||
};
|
||||
|
||||
prcmu@80157000 {
|
||||
ab8500 {
|
||||
ab8500_usb {
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&usb_a_1_default>;
|
||||
pinctrl-1 = <&usb_a_1_sleep>;
|
||||
};
|
||||
|
||||
ab8500-regulators {
|
||||
ab8500_ldo_aux1 {
|
||||
/* Used for VDD for sensors */
|
||||
regulator-name = "V-SENSORS-VDD";
|
||||
regulator-min-microvolt = <3000000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
};
|
||||
|
||||
ab8500_ldo_aux2 {
|
||||
/* Used for VIO for sensors */
|
||||
regulator-name = "V-SENSORS-VIO";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
};
|
||||
|
||||
ab8500_ldo_aux3 {
|
||||
/* Used for voltage for external MMC/SD card */
|
||||
regulator-name = "V-MMC-SD";
|
||||
regulator-min-microvolt = <1200000>;
|
||||
regulator-max-microvolt = <2910000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
/* I2C0 */
|
||||
i2c@80004000 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&i2c0_a_1_default>;
|
||||
pinctrl-1 = <&i2c0_a_1_sleep>;
|
||||
|
||||
proximity@44 {
|
||||
/* Janice has the GP2AP002A00F with light sensor */
|
||||
compatible = "sharp,gp2ap002a00f";
|
||||
clock-frequency = <400000>;
|
||||
reg = <0x44>;
|
||||
|
||||
interrupt-parent = <&gpio4>;
|
||||
interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
|
||||
vdd-supply = <&ab8500_ldo_aux1_reg>;
|
||||
vio-supply = <&ab8500_ldo_aux2_reg>;
|
||||
/* ADC channel AUX2 to read ALSOUT ambient light sensor out */
|
||||
io-channels = <&gp2a_shunt>;
|
||||
io-channel-names = "alsout";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&gp2ap002_janice_default>;
|
||||
/* B1 mode (arch/arm/mach-ux500/include/mach/gp2a.h) */
|
||||
sharp,proximity-far-hysteresis = /bits/ 8 <0x40>;
|
||||
sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
|
||||
};
|
||||
};
|
||||
|
||||
/* I2C1 on GPIO16 and GPIO17 also called "MUS I2C" */
|
||||
i2c@80122000 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default","sleep";
|
||||
pinctrl-0 = <&i2c1_b_2_default>;
|
||||
pinctrl-1 = <&i2c1_b_2_sleep>;
|
||||
|
||||
/* Texas Instruments TSU6111 micro USB switch */
|
||||
usb-switch@25 {
|
||||
compatible = "ti,tsu6111";
|
||||
reg = <0x25>;
|
||||
/* Interrupt JACK_INT_N on GPIO95 */
|
||||
interrupt-parent = <&gpio2>;
|
||||
interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&tsu6111_janice_default>;
|
||||
};
|
||||
};
|
||||
|
||||
/* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */
|
||||
i2c@80128000 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&i2c2_b_2_default>;
|
||||
pinctrl-1 = <&i2c2_b_2_sleep>;
|
||||
|
||||
gyroscope@68 {
|
||||
compatible = "invensense,mpu3050";
|
||||
reg = <0x68>;
|
||||
/* GPIO226 interrupt */
|
||||
interrupt-parent = <&gpio7>;
|
||||
interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
|
||||
/* FIXME: no idea about this */
|
||||
mount-matrix = "1", "0", "0",
|
||||
"0", "1", "0",
|
||||
"0", "0", "1";
|
||||
vlogic-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
|
||||
vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mpu3050_janice_default>;
|
||||
|
||||
/*
|
||||
* The MPU-3050 acts as a hub for the
|
||||
* accelerometer.
|
||||
*/
|
||||
i2c-gate {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
/* Bosch BMA222 accelerometer */
|
||||
accelerometer@08 {
|
||||
compatible = "bosch,bma222";
|
||||
reg = <0x08>;
|
||||
/* FIXME: no idea about this */
|
||||
mount-matrix = "1", "0", "0",
|
||||
"0", "1", "0",
|
||||
"0", "0", "1";
|
||||
vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
|
||||
vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
/* I2C3 */
|
||||
i2c@80110000 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&i2c3_c_2_default>;
|
||||
pinctrl-1 = <&i2c3_c_2_sleep>;
|
||||
|
||||
/* Atmel mXT224E touchscreen */
|
||||
touchscreen@4a {
|
||||
compatible = "atmel,maxtouch";
|
||||
reg = <0x4a>;
|
||||
/* GPIO218 (TSP_INT_1V8) */
|
||||
interrupt-parent = <&gpio6>;
|
||||
interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
|
||||
/* VDDA is "analog supply", 2.57-3.47 V */
|
||||
vdda-supply = <&ldo_tsp_3v3_reg>;
|
||||
/* VDD is "digital supply" 1.71-3.47V */
|
||||
vdd-supply = <&ldo_tsp_1v8_reg>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&tsp_default>;
|
||||
};
|
||||
};
|
||||
|
||||
mcde@a0350000 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&dpi_default_mode>;
|
||||
|
||||
port {
|
||||
display_out: endpoint {
|
||||
remote-endpoint = <&panel_in>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
/*
|
||||
* This extends the MC0_A_2 default config to include
|
||||
* the card detect GPIO217 line.
|
||||
*/
|
||||
sdi0 {
|
||||
mc0_a_2_default {
|
||||
default_cfg4 {
|
||||
pins = "GPIO217_AH12"; /* card detect */
|
||||
ste,config = <&gpio_in_pd>;
|
||||
};
|
||||
};
|
||||
};
|
||||
mcde {
|
||||
dpi_default_mode: dpi_default {
|
||||
default_mux1 {
|
||||
/* Mux in all the data lines */
|
||||
function = "lcd";
|
||||
groups =
|
||||
/* Data lines D0-D7 GPIO70..GPIO77 */
|
||||
"lcd_d0_d7_a_1",
|
||||
/* Data lines D8-D11 GPIO78..GPIO81 */
|
||||
"lcd_d8_d11_a_1",
|
||||
/* Data lines D12-D15 GPIO82..GPIO85 */
|
||||
"lcd_d12_d15_a_1",
|
||||
/* Data lines D16-D23 GPIO161..GPIO168 */
|
||||
"lcd_d16_d23_b_1";
|
||||
};
|
||||
default_mux2 {
|
||||
function = "lcda";
|
||||
/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
|
||||
groups = "lcdaclk_b_1", "lcda_b_1";
|
||||
};
|
||||
/* Input, no pull-up is the default state for pins used for an alt function */
|
||||
default_cfg1 {
|
||||
pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
|
||||
ste,config = <&in_nopull>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* GPIO for panel reset control */
|
||||
panel {
|
||||
panel_default_mode: panel_default {
|
||||
janice_cfg1 {
|
||||
/* Reset line */
|
||||
pins = "GPIO139_C9";
|
||||
ste,config = <&gpio_out_lo>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* GPIO that enables the LDO regulator for the eMMC */
|
||||
emmc-ldo {
|
||||
emmc_ldo_en_default_mode: emmc_ldo_default {
|
||||
/* LDO enable on GPIO6 */
|
||||
janice_cfg1 {
|
||||
pins = "GPIO6_AF6";
|
||||
ste,config = <&gpio_out_hi>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* GPIO that enables the LDO regulator for the touchscreen */
|
||||
tsp-ldo {
|
||||
tsp_ldo_en_default_mode: tsp_ldo_default {
|
||||
/* LDO enable on GPIO94 */
|
||||
janice_cfg1 {
|
||||
pins = "GPIO94_D7";
|
||||
ste,config = <&gpio_out_hi>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* GPIO that enables the LDO regulator for the key LED */
|
||||
key-led {
|
||||
en_led_ldo_default_mode: en_led_ldo_default {
|
||||
/* EN_LED_LDO on GPIO68 */
|
||||
janice_cfg1 {
|
||||
pins = "GPIO68_E1";
|
||||
ste,config = <&gpio_out_hi>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* GPIO that enables the LDO regulator for the touchkeys */
|
||||
touchkey-ldo {
|
||||
tsp_ldo_on2_default_mode: tsp_ldo_on2_default {
|
||||
/* TSP_LDO_ON2 on GPIO89 */
|
||||
janice_cfg1 {
|
||||
pins = "GPIO89_E6";
|
||||
ste,config = <&gpio_out_lo>;
|
||||
};
|
||||
};
|
||||
};
|
||||
touchkey {
|
||||
touchkey_default_mode: touchkey_default {
|
||||
janice_cfg1 {
|
||||
/* Interrupt */
|
||||
pins = "GPIO198_AG25";
|
||||
ste,config = <&gpio_in_nopull>;
|
||||
};
|
||||
janice_cfg2 {
|
||||
/* Reset, actually completely unused (not routed) */
|
||||
pins = "GPIO205_AG23";
|
||||
ste,config = <&gpio_in_pd>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* GPIO that enabled the LDO regulator for the LCD display */
|
||||
lcd-ldo {
|
||||
lcd_pwr_en_default_mode: lcd_pwr_en_default {
|
||||
/* LCD_PWR_EN on GPIO219 */
|
||||
janice_cfg1 {
|
||||
pins = "GPIO219_AG10";
|
||||
ste,config = <&gpio_out_hi>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* GPIO that enables the WLAN internal LDO regulators */
|
||||
wlan-ldo {
|
||||
wlan_ldo_en_default: wlan_ldo_default {
|
||||
/* GPIO222 BT_VREG_ON */
|
||||
janice_cfg1 {
|
||||
pins = "GPIO222_AJ9";
|
||||
ste,config = <&gpio_out_lo>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* GPIO keys */
|
||||
gpio-keys {
|
||||
gpio_keys_default_mode: gpio_keys_default {
|
||||
skomer_cfg1 {
|
||||
pins = "GPIO67_G2", /* VOL UP */
|
||||
"GPIO91_B6", /* HOME */
|
||||
"GPIO92_D6"; /* VOL DOWN */
|
||||
ste,config = <&gpio_in_pu>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* Interrupt line for the Atmel MXT228 touchscreen */
|
||||
tsp {
|
||||
tsp_default: tsp_default {
|
||||
janice_cfg1 {
|
||||
pins = "GPIO218_AH11"; /* TSP_INT_1V8 */
|
||||
ste,config = <&gpio_in_nopull>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* Reset line for the Yamaha YAS529 magnetometer */
|
||||
yas529 {
|
||||
yas529_default: yas529_janice {
|
||||
janice_cfg1 {
|
||||
pins = "GPIO204_AF23";
|
||||
ste,config = <&gpio_out_hi>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* Interrupt line for light/proximity sensor GP2AP002 */
|
||||
gp2ap002 {
|
||||
gp2ap002_janice_default: gp2ap002_janice {
|
||||
janice_cfg1 {
|
||||
pins = "GPIO146_D13";
|
||||
ste,config = <&gpio_in_nopull>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* Interrupt line for Invensense MPU3050 gyroscope */
|
||||
mpu3050 {
|
||||
mpu3050_janice_default: mpu3050_janice {
|
||||
janice_cfg1 {
|
||||
/* GPIO226 used for IRQ */
|
||||
pins = "GPIO226_AF8";
|
||||
ste,config = <&gpio_in_nopull>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* GPIO-based I2C bus for magnetometer and NCP6914 */
|
||||
i2c-gpio-0 {
|
||||
i2c_gpio_0_default: i2c_gpio_0 {
|
||||
janice_cfg1 {
|
||||
pins = "GPIO143_D12", "GPIO144_B13";
|
||||
ste,config = <&gpio_in_nopull>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* GPIO-based I2C bus for the Cypress touchkeys */
|
||||
i2c-gpio-1 {
|
||||
i2c_gpio_1_default: i2c_gpio_1 {
|
||||
janice_cfg1 {
|
||||
pins = "GPIO196_AG26", "GPIO197_AH24";
|
||||
ste,config = <&gpio_in_nopull>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* GPIO-based I2C bus for the Immersion ISA1200 */
|
||||
i2c-gpio-2 {
|
||||
i2c_gpio_2_default: i2c_gpio_2 {
|
||||
janice_cfg1 {
|
||||
pins = "GPIO201_AF24", "GPIO202_AF25";
|
||||
ste,config = <&gpio_in_nopull>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* GPIO-based I2C bus for the NFC */
|
||||
i2c-gpio-3 {
|
||||
i2c_gpio_3_default: i2c_gpio_3 {
|
||||
janice_cfg1 {
|
||||
pins = "GPIO151_D17", "GPIO152_D16";
|
||||
ste,config = <&gpio_in_nopull>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* GPIO-based SPI bus for the display */
|
||||
spi-gpio-0 {
|
||||
spi_gpio_0_default: spi_gpio_0 {
|
||||
janice_cfg1 {
|
||||
pins = "GPIO220_AH10", "GPIO223_AH9", "GPIO224_AG9";
|
||||
ste,config = <&gpio_out_hi>;
|
||||
};
|
||||
/* This pin is unused but belongs with this SPI block */
|
||||
janice_cfg2 {
|
||||
pins = "GPIO225_AG8";
|
||||
ste,config = <&in_pd>;
|
||||
};
|
||||
};
|
||||
};
|
||||
wlan {
|
||||
wlan_default_mode: wlan_default {
|
||||
/* GPIO215 used for RESET_N */
|
||||
janice_cfg1 {
|
||||
pins = "GPIO215_AH13";
|
||||
ste,config = <&gpio_out_lo>;
|
||||
};
|
||||
/* GPIO216 for WL_HOST_WAKE */
|
||||
janice_cfg2 {
|
||||
pins = "GPIO216_AG12";
|
||||
ste,config = <&gpio_in_pd>;
|
||||
};
|
||||
};
|
||||
};
|
||||
bluetooth {
|
||||
bluetooth_default_mode: bluetooth_default {
|
||||
janice_cfg1 {
|
||||
pins = "GPIO199_AH23";
|
||||
ste,config = <&gpio_out_lo>;
|
||||
};
|
||||
janice_cfg2 {
|
||||
pins = "GPIO97_D9";
|
||||
ste,config = <&gpio_in_nopull>;
|
||||
};
|
||||
janice_cfg3 {
|
||||
pins = "GPIO209_AG15";
|
||||
ste,config = <&gpio_out_hi>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* Interrupt line for TI TSU6111 Micro USB switch */
|
||||
tsu6111 {
|
||||
tsu6111_janice_default: tsu6111_janice {
|
||||
janice_cfg1 {
|
||||
/* GPIO95 used for IRQ */
|
||||
pins = "GPIO95_E8";
|
||||
ste,config = <&gpio_in_nopull>;
|
||||
};
|
||||
};
|
||||
};
|
||||
nfc {
|
||||
pn547_janice_default: pn547_janice {
|
||||
/* Interrupt line */
|
||||
janice_cfg1 {
|
||||
pins = "GPIO32_V2";
|
||||
ste,config = <&gpio_in_nopull>;
|
||||
};
|
||||
/* Enable and firmware GPIOs */
|
||||
janice_cfg2 {
|
||||
pins = "GPIO31_V3", "GPIO88_C4";
|
||||
ste,config = <&gpio_out_lo>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
Загрузка…
Ссылка в новой задаче