powerpc/85xx: Add dts for p1025rdb board

P1025RDB Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus

PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot

10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using AtherosTM AR8021
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021

USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot

Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display

Signed-off-by: Zhicheng Fan <b32736@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This commit is contained in:
Zhicheng Fan 2012-02-13 22:06:23 +00:00 коммит произвёл Kumar Gala
Родитель 6886780abf
Коммит 79ad57400c
3 изменённых файлов: 509 добавлений и 0 удалений

Просмотреть файл

@ -0,0 +1,286 @@
/*
* P1025 RDB Device Tree Source stub (no addresses or top-level ranges)
*
* Copyright 2011 Freescale Semiconductor Inc.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* * Neither the name of Freescale Semiconductor nor the
* names of its contributors may be used to endorse or promote products
* derived from this software without specific prior written permission.
*
*
* ALTERNATIVELY, this software may be distributed under the terms of the
* GNU General Public License ("GPL") as published by the Free Software
* Foundation, either version 2 of that License or (at your option) any
* later version.
*
* THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
&lbc {
nor@0,0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "cfi-flash";
reg = <0x0 0x0 0x1000000>;
bank-width = <2>;
device-width = <1>;
partition@0 {
/* This location must not be altered */
/* 256KB for Vitesse 7385 Switch firmware */
reg = <0x0 0x00040000>;
label = "NOR Vitesse-7385 Firmware";
read-only;
};
partition@40000 {
/* 256KB for DTB Image */
reg = <0x00040000 0x00040000>;
label = "NOR DTB Image";
};
partition@80000 {
/* 3.5 MB for Linux Kernel Image */
reg = <0x00080000 0x00380000>;
label = "NOR Linux Kernel Image";
};
partition@400000 {
/* 11MB for JFFS2 based Root file System */
reg = <0x00400000 0x00b00000>;
label = "NOR JFFS2 Root File System";
};
partition@f00000 {
/* This location must not be altered */
/* 512KB for u-boot Bootloader Image */
/* 512KB for u-boot Environment Variables */
reg = <0x00f00000 0x00100000>;
label = "NOR U-Boot Image";
read-only;
};
};
nand@1,0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,p1025-fcm-nand",
"fsl,elbc-fcm-nand";
reg = <0x1 0x0 0x40000>;
partition@0 {
/* This location must not be altered */
/* 1MB for u-boot Bootloader Image */
reg = <0x0 0x00100000>;
label = "NAND U-Boot Image";
read-only;
};
partition@100000 {
/* 1MB for DTB Image */
reg = <0x00100000 0x00100000>;
label = "NAND DTB Image";
};
partition@200000 {
/* 4MB for Linux Kernel Image */
reg = <0x00200000 0x00400000>;
label = "NAND Linux Kernel Image";
};
partition@600000 {
/* 4MB for Compressed Root file System Image */
reg = <0x00600000 0x00400000>;
label = "NAND Compressed RFS Image";
};
partition@a00000 {
/* 7MB for JFFS2 based Root file System */
reg = <0x00a00000 0x00700000>;
label = "NAND JFFS2 Root File System";
};
partition@1100000 {
/* 15MB for JFFS2 based Root file System */
reg = <0x01100000 0x00f00000>;
label = "NAND Writable User area";
};
};
};
&soc {
i2c@3000 {
rtc@68 {
compatible = "dallas,ds1339";
reg = <0x68>;
};
};
spi@7000 {
flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "spansion,s25sl12801";
reg = <0>;
spi-max-frequency = <40000000>; /* input clock */
partition@u-boot {
/* 512KB for u-boot Bootloader Image */
reg = <0x0 0x00080000>;
label = "u-boot";
read-only;
};
partition@dtb {
/* 512KB for DTB Image */
reg = <0x00080000 0x00080000>;
label = "dtb";
};
partition@kernel {
/* 4MB for Linux Kernel Image */
reg = <0x00100000 0x00400000>;
label = "kernel";
};
partition@fs {
/* 4MB for Compressed RFS Image */
reg = <0x00500000 0x00400000>;
label = "file system";
};
partition@jffs-fs {
/* 7MB for JFFS2 based RFS */
reg = <0x00900000 0x00700000>;
label = "file system jffs2";
};
};
};
usb@22000 {
phy_type = "ulpi";
};
/* USB2 is shared with localbus, so it must be disabled
by default. We can't put 'status = "disabled";' here
since U-Boot doesn't clear the status property when
it enables USB2. OTOH, U-Boot does create a new node
when there isn't any. So, just comment it out.
usb@23000 {
phy_type = "ulpi";
};
*/
mdio@24000 {
phy0: ethernet-phy@0 {
interrupt-parent = <&mpic>;
interrupts = <3 1>;
reg = <0x0>;
};
phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
interrupts = <2 1>;
reg = <0x1>;
};
tbi0: tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
mdio@25000 {
tbi1: tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
mdio@26000 {
tbi2: tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
enet0: ethernet@b0000 {
fixed-link = <1 1 1000 0 0>;
phy-connection-type = "rgmii-id";
};
enet1: ethernet@b1000 {
phy-handle = <&phy0>;
tbi-handle = <&tbi1>;
phy-connection-type = "sgmii";
};
enet2: ethernet@b2000 {
phy-handle = <&phy1>;
phy-connection-type = "rgmii-id";
};
par_io@e0100 {
#address-cells = <1>;
#size-cells = <1>;
reg = <0xe0100 0x60>;
ranges = <0x0 0xe0100 0x60>;
device_type = "par_io";
num-ports = <3>;
pio1: ucc_pin@01 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
0x0 0x17 0x2 0x0 0x2 0x0 /* CLK12 */
0x0 0x18 0x2 0x0 0x1 0x0 /* CLK9 */
0x0 0x7 0x1 0x0 0x2 0x0 /* ENET1_TXD0_SER1_TXD0 */
0x0 0x9 0x1 0x0 0x2 0x0 /* ENET1_TXD1_SER1_TXD1 */
0x0 0xb 0x1 0x0 0x2 0x0 /* ENET1_TXD2_SER1_TXD2 */
0x0 0xc 0x1 0x0 0x2 0x0 /* ENET1_TXD3_SER1_TXD3 */
0x0 0x6 0x2 0x0 0x2 0x0 /* ENET1_RXD0_SER1_RXD0 */
0x0 0xa 0x2 0x0 0x2 0x0 /* ENET1_RXD1_SER1_RXD1 */
0x0 0xe 0x2 0x0 0x2 0x0 /* ENET1_RXD2_SER1_RXD2 */
0x0 0xf 0x2 0x0 0x2 0x0 /* ENET1_RXD3_SER1_RXD3 */
0x0 0x5 0x1 0x0 0x2 0x0 /* ENET1_TX_EN_SER1_RTS_B */
0x0 0xd 0x1 0x0 0x2 0x0 /* ENET1_TX_ER */
0x0 0x4 0x2 0x0 0x2 0x0 /* ENET1_RX_DV_SER1_CTS_B */
0x0 0x8 0x2 0x0 0x2 0x0 /* ENET1_RX_ER_SER1_CD_B */
0x0 0x11 0x2 0x0 0x2 0x0 /* ENET1_CRS */
0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */
};
pio2: ucc_pin@02 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
0x1 0xb 0x2 0x0 0x1 0x0 /* CLK13 */
0x1 0x7 0x1 0x0 0x2 0x0 /* ENET5_TXD0_SER5_TXD0 */
0x1 0xa 0x1 0x0 0x2 0x0 /* ENET5_TXD1_SER5_TXD1 */
0x1 0x6 0x2 0x0 0x2 0x0 /* ENET5_RXD0_SER5_RXD0 */
0x1 0x9 0x2 0x0 0x2 0x0 /* ENET5_RXD1_SER5_RXD1 */
0x1 0x5 0x1 0x0 0x2 0x0 /* ENET5_TX_EN_SER5_RTS_B */
0x1 0x4 0x2 0x0 0x2 0x0 /* ENET5_RX_DV_SER5_CTS_B */
0x1 0x8 0x2 0x0 0x2 0x0>; /* ENET5_RX_ER_SER5_CD_B */
};
};
};

Просмотреть файл

@ -0,0 +1,135 @@
/*
* P1025 RDB Device Tree Source (32-bit address map)
*
* Copyright 2011 Freescale Semiconductor Inc.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* * Neither the name of Freescale Semiconductor nor the
* names of its contributors may be used to endorse or promote products
* derived from this software without specific prior written permission.
*
*
* ALTERNATIVELY, this software may be distributed under the terms of the
* GNU General Public License ("GPL") as published by the Free Software
* Foundation, either version 2 of that License or (at your option) any
* later version.
*
* THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/include/ "fsl/p1021si-pre.dtsi"
/ {
model = "fsl,P1025RDB";
compatible = "fsl,P1025RDB";
memory {
device_type = "memory";
};
lbc: localbus@ffe05000 {
reg = <0 0xffe05000 0 0x1000>;
/* NOR, NAND Flashes */
ranges = <0x0 0x0 0x0 0xef000000 0x01000000
0x1 0x0 0x0 0xff800000 0x00040000>;
};
soc: soc@ffe00000 {
ranges = <0x0 0x0 0xffe00000 0x100000>;
};
pci0: pcie@ffe09000 {
ranges = <0x2000000 0x0 0xe0000000 0 0xe0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
reg = <0 0xffe09000 0 0x1000>;
pcie@0 {
ranges = <0x2000000 0x0 0xe0000000
0x2000000 0x0 0xe0000000
0x0 0x20000000
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x100000>;
};
};
pci1: pcie@ffe0a000 {
reg = <0 0xffe0a000 0 0x1000>;
ranges = <0x2000000 0x0 0xe0000000 0 0xe0000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
pcie@0 {
ranges = <0x2000000 0x0 0xe0000000
0x2000000 0x0 0xe0000000
0x0 0x20000000
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x100000>;
};
};
qe: qe@ffe80000 {
ranges = <0x0 0x0 0xffe80000 0x40000>;
reg = <0 0xffe80000 0 0x480>;
brg-frequency = <0>;
bus-frequency = <0>;
status = "disabled"; /* no firmware loaded */
enet3: ucc@2000 {
device_type = "network";
compatible = "ucc_geth";
rx-clock-name = "clk12";
tx-clock-name = "clk9";
pio-handle = <&pio1>;
phy-handle = <&qe_phy0>;
phy-connection-type = "mii";
};
mdio@2120 {
qe_phy0: ethernet-phy@0 {
interrupt-parent = <&mpic>;
interrupts = <4 1 0 0>;
reg = <0x6>;
device_type = "ethernet-phy";
};
qe_phy1: ethernet-phy@03 {
interrupt-parent = <&mpic>;
interrupts = <5 1 0 0>;
reg = <0x3>;
device_type = "ethernet-phy";
};
tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
enet4: ucc@2400 {
device_type = "network";
compatible = "ucc_geth";
rx-clock-name = "none";
tx-clock-name = "clk13";
pio-handle = <&pio2>;
phy-handle = <&qe_phy1>;
phy-connection-type = "rmii";
};
};
};
/include/ "p1025rdb.dtsi"
/include/ "fsl/p1021si-post.dtsi"

Просмотреть файл

@ -0,0 +1,88 @@
/*
* P1025 RDB Device Tree Source (36-bit address map)
*
* Copyright 2011 Freescale Semiconductor Inc.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* * Neither the name of Freescale Semiconductor nor the
* names of its contributors may be used to endorse or promote products
* derived from this software without specific prior written permission.
*
*
* ALTERNATIVELY, this software may be distributed under the terms of the
* GNU General Public License ("GPL") as published by the Free Software
* Foundation, either version 2 of that License or (at your option) any
* later version.
*
* THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/include/ "fsl/p1021si-pre.dtsi"
/ {
model = "fsl,P1025RDB";
compatible = "fsl,P1025RDB";
memory {
device_type = "memory";
};
lbc: localbus@fffe05000 {
reg = <0xf 0xffe05000 0 0x1000>;
/* NOR, NAND Flashes */
ranges = <0x0 0x0 0xf 0xef000000 0x01000000
0x1 0x0 0xf 0xff800000 0x00040000>;
};
soc: soc@fffe00000 {
ranges = <0x0 0xf 0xffe00000 0x100000>;
};
pci0: pcie@fffe09000 {
reg = <0xf 0xffe09000 0 0x1000>;
ranges = <0x2000000 0x0 0xe0000000 0xe 0x20000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
pcie@0 {
ranges = <0x2000000 0x0 0xe0000000
0x2000000 0x0 0xe0000000
0x0 0x20000000
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x100000>;
};
};
pci1: pcie@fffe0a000 {
reg = <0xf 0xffe0a000 0 0x1000>;
ranges = <0x2000000 0x0 0xe0000000 0xc 0x00000000 0x0 0x20000000
0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x10000>;
pcie@0 {
ranges = <0x2000000 0x0 0xe0000000
0x2000000 0x0 0xe0000000
0x0 0x20000000
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x100000>;
};
};
};
/include/ "p1025rdb.dtsi"
/include/ "fsl/p1021si-post.dtsi"