phy: amlogic: meson8b-usb2: unset the IDDQ bit during PHY power-on

The vendor driver unsets the set_iddig bit during power-on as well and
sets it when suspending the PHY. I did not notice this in the vendor
driver first, because it's part of the dwc_otg driver there (instead of
their PHY code). While here, also add all other REG_DBG_UART register
bit definitions.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Thomas Graichen <thomas.graichen@gmail.com>
Link: https://lore.kernel.org/r/20200512222424.549351-6-martin.blumenstingl@googlemail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

drivers/phy/amlogic/phy-meson8b-usb2.c

@@ -78,6 +78,17 @@
 	#define REG_ADP_BC_ACA_PIN_FLOAT		BIT(26)
 
 #define REG_DBG_UART					0x10
+	#define REG_DBG_UART_BYPASS_SEL			BIT(0)
+	#define REG_DBG_UART_BYPASS_DM_EN		BIT(1)
+	#define REG_DBG_UART_BYPASS_DP_EN		BIT(2)
+	#define REG_DBG_UART_BYPASS_DM_DATA		BIT(3)
+	#define REG_DBG_UART_BYPASS_DP_DATA		BIT(4)
+	#define REG_DBG_UART_FSV_MINUS			BIT(5)
+	#define REG_DBG_UART_FSV_PLUS			BIT(6)
+	#define REG_DBG_UART_FSV_BURN_IN_TEST		BIT(7)
+	#define REG_DBG_UART_LOOPBACK_EN_B		BIT(8)
+	#define REG_DBG_UART_SET_IDDQ			BIT(9)
+	#define REG_DBG_UART_ATE_RESET			BIT(10)
 
 #define REG_TEST					0x14
 	#define REG_TEST_DATA_IN_MASK			GENMASK(3, 0)
@@ -172,8 +183,11 @@ static int phy_meson8b_usb2_power_on(struct phy *phy)
 	regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_SOF_TOGGLE_OUT,
 			   REG_CTRL_SOF_TOGGLE_OUT);
 
-	if (priv->dr_mode == USB_DR_MODE_HOST &&
-	    priv->match->host_enable_aca) {
+	if (priv->dr_mode == USB_DR_MODE_HOST) {
+		regmap_update_bits(priv->regmap, REG_DBG_UART,
+				   REG_DBG_UART_SET_IDDQ, 0);
+
+		if (priv->match->host_enable_aca) {
 			regmap_update_bits(priv->regmap, REG_ADP_BC,
 					   REG_ADP_BC_ACA_ENABLE,
 					   REG_ADP_BC_ACA_ENABLE);
@@ -188,6 +202,7 @@ static int phy_meson8b_usb2_power_on(struct phy *phy)
 				return -EINVAL;
 			}
 		}
+	}
 
 	return 0;
 }
@@ -196,6 +211,11 @@ static int phy_meson8b_usb2_power_off(struct phy *phy)
 {
 	struct phy_meson8b_usb2_priv *priv = phy_get_drvdata(phy);
 
+	if (priv->dr_mode == USB_DR_MODE_HOST)
+		regmap_update_bits(priv->regmap, REG_DBG_UART,
+				   REG_DBG_UART_SET_IDDQ,
+				   REG_DBG_UART_SET_IDDQ);
+
 	clk_disable_unprepare(priv->clk_usb);
 	clk_disable_unprepare(priv->clk_usb_general);