[SCSI] pm80xx: Resetting the phy state.

Setting the phy state for hard reset response.
After sending hard reset for a device ,phy down event sets
the phy state to zero but for phy up event it will not set
the phy state again.This will cause problem to successive
hard resets.

Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

drivers/scsi/pm8001/pm8001_hwi.c

@@ -3403,6 +3403,7 @@ hw_event_sas_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
 	unsigned long flags;
 	u8 deviceType = pPayload->sas_identify.dev_type;
 	port->port_state =  portstate;
+	phy->phy_state = PHY_STATE_LINK_UP_SPC;
 	PM8001_MSG_DBG(pm8001_ha,
 		pm8001_printk("HW_EVENT_SAS_PHY_UP port id = %d, phy id = %d\n",
 		port_id, phy_id));
@@ -3483,6 +3484,7 @@ hw_event_sata_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
 		pm8001_printk("HW_EVENT_SATA_PHY_UP port id = %d,"
 		" phy id = %d\n", port_id, phy_id));
 	port->port_state =  portstate;
+	phy->phy_state = PHY_STATE_LINK_UP_SPC;
 	port->port_attached = 1;
 	pm8001_get_lrate_mode(phy, link_rate);
 	phy->phy_type |= PORT_TYPE_SATA;

drivers/scsi/pm8001/pm8001_hwi.h

@@ -131,6 +131,10 @@
 #define LINKRATE_30			(0x02 << 8)
 #define LINKRATE_60			(0x04 << 8)
 
+/* for phy state */
+
+#define PHY_STATE_LINK_UP_SPC		0x1
+
 /* for new SPC controllers MEMBASE III is shared between BIOS and DATA */
 #define GSM_SM_BASE			0x4F0000
 struct mpi_msg_hdr{

drivers/scsi/pm8001/pm80xx_hwi.c

@@ -2894,6 +2894,7 @@ hw_event_sas_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
 	unsigned long flags;
 	u8 deviceType = pPayload->sas_identify.dev_type;
 	port->port_state = portstate;
+	phy->phy_state = PHY_STATE_LINK_UP_SPCV;
 	PM8001_MSG_DBG(pm8001_ha, pm8001_printk(
 		"portid:%d; phyid:%d; linkrate:%d; "
 		"portstate:%x; devicetype:%x\n",
@@ -2978,6 +2979,7 @@ hw_event_sata_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb)
 				port_id, phy_id, link_rate, portstate));
 
 	port->port_state = portstate;
+	phy->phy_state = PHY_STATE_LINK_UP_SPCV;
 	port->port_attached = 1;
 	pm8001_get_lrate_mode(phy, link_rate);
 	phy->phy_type |= PORT_TYPE_SATA;

drivers/scsi/pm8001/pm80xx_hwi.h

@@ -215,6 +215,8 @@
 #define SAS_DOPNRJT_RTRY_TMO            128
 #define SAS_COPNRJT_RTRY_TMO            128
 
+/* for phy state */
+#define PHY_STATE_LINK_UP_SPCV		0x2
 /*
   Making ORR bigger than IT NEXUS LOSS which is 2000000us = 2 second.
   Assuming a bigger value 3 second, 3000000/128 = 23437.5 where 128