From fa365e4d729065b5e85165df3dc9699ed47489cc Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Wed, 25 Sep 2013 02:36:52 +0200 Subject: [PATCH 1/2] gpio/omap: maintain GPIO and IRQ usage separately The GPIO OMAP controller pins can be used as IRQ and GPIO independently so is necessary to keep track GPIO pins and IRQ lines usage separately to make sure that the bank will always be enabled while being used. Also move gpio_is_input() definition in preparation for the next patch that setups the controller's irq_chip driver when a caller requests an interrupt line. Cc: stable@vger.kernel.org Acked-by: Stephen Warren Tested-by: George Cherian Tested-by: Aaro Koskinen Tested-by: Lars Poeschel Reviewed-by: Kevin Hilman Tested-by: Kevin Hilman Acked-by: Santosh Shilimkar Acked-by: Tony Lindgren Signed-off-by: Javier Martinez Canillas Signed-off-by: Linus Walleij --- drivers/gpio/gpio-omap.c | 35 +++++++++++++++++++++-------------- 1 file changed, 21 insertions(+), 14 deletions(-) diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c index 0ff43552d472..a4fe038d090e 100644 --- a/drivers/gpio/gpio-omap.c +++ b/drivers/gpio/gpio-omap.c @@ -63,6 +63,7 @@ struct gpio_bank { struct gpio_chip chip; struct clk *dbck; u32 mod_usage; + u32 irq_usage; u32 dbck_enable_mask; bool dbck_enabled; struct device *dev; @@ -86,6 +87,9 @@ struct gpio_bank { #define GPIO_BIT(bank, gpio) (1 << GPIO_INDEX(bank, gpio)) #define GPIO_MOD_CTRL_BIT BIT(0) +#define BANK_USED(bank) (bank->mod_usage || bank->irq_usage) +#define LINE_USED(line, offset) (line & (1 << offset)) + static int irq_to_gpio(struct gpio_bank *bank, unsigned int gpio_irq) { return bank->chip.base + gpio_irq; @@ -420,6 +424,13 @@ static int _set_gpio_triggering(struct gpio_bank *bank, int gpio, return 0; } +static int gpio_is_input(struct gpio_bank *bank, int mask) +{ + void __iomem *reg = bank->base + bank->regs->direction; + + return __raw_readl(reg) & mask; +} + static int gpio_irq_type(struct irq_data *d, unsigned type) { struct gpio_bank *bank = irq_data_get_irq_chip_data(d); @@ -427,7 +438,7 @@ static int gpio_irq_type(struct irq_data *d, unsigned type) int retval; unsigned long flags; - if (WARN_ON(!bank->mod_usage)) + if (WARN_ON(!BANK_USED(bank))) return -EINVAL; #ifdef CONFIG_ARCH_OMAP1 @@ -447,6 +458,7 @@ static int gpio_irq_type(struct irq_data *d, unsigned type) spin_lock_irqsave(&bank->lock, flags); retval = _set_gpio_triggering(bank, GPIO_INDEX(bank, gpio), type); + bank->irq_usage |= 1 << GPIO_INDEX(bank, gpio); spin_unlock_irqrestore(&bank->lock, flags); if (type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH)) @@ -603,7 +615,7 @@ static int omap_gpio_request(struct gpio_chip *chip, unsigned offset) * If this is the first gpio_request for the bank, * enable the bank module. */ - if (!bank->mod_usage) + if (!BANK_USED(bank)) pm_runtime_get_sync(bank->dev); spin_lock_irqsave(&bank->lock, flags); @@ -619,7 +631,7 @@ static int omap_gpio_request(struct gpio_chip *chip, unsigned offset) __raw_writel(__raw_readl(reg) | (1 << offset), reg); } - if (bank->regs->ctrl && !bank->mod_usage) { + if (bank->regs->ctrl && !BANK_USED(bank)) { void __iomem *reg = bank->base + bank->regs->ctrl; u32 ctrl; @@ -654,7 +666,7 @@ static void omap_gpio_free(struct gpio_chip *chip, unsigned offset) bank->mod_usage &= ~(1 << offset); - if (bank->regs->ctrl && !bank->mod_usage) { + if (bank->regs->ctrl && !BANK_USED(bank)) { void __iomem *reg = bank->base + bank->regs->ctrl; u32 ctrl; @@ -672,7 +684,7 @@ static void omap_gpio_free(struct gpio_chip *chip, unsigned offset) * If this is the last gpio to be freed in the bank, * disable the bank module. */ - if (!bank->mod_usage) + if (!BANK_USED(bank)) pm_runtime_put(bank->dev); } @@ -762,8 +774,10 @@ static void gpio_irq_shutdown(struct irq_data *d) struct gpio_bank *bank = irq_data_get_irq_chip_data(d); unsigned int gpio = irq_to_gpio(bank, d->hwirq); unsigned long flags; + unsigned offset = GPIO_INDEX(bank, gpio); spin_lock_irqsave(&bank->lock, flags); + bank->irq_usage &= ~(1 << offset); _reset_gpio(bank, gpio); spin_unlock_irqrestore(&bank->lock, flags); } @@ -897,13 +911,6 @@ static int gpio_input(struct gpio_chip *chip, unsigned offset) return 0; } -static int gpio_is_input(struct gpio_bank *bank, int mask) -{ - void __iomem *reg = bank->base + bank->regs->direction; - - return __raw_readl(reg) & mask; -} - static int gpio_get(struct gpio_chip *chip, unsigned offset) { struct gpio_bank *bank; @@ -1400,7 +1407,7 @@ void omap2_gpio_prepare_for_idle(int pwr_mode) struct gpio_bank *bank; list_for_each_entry(bank, &omap_gpio_list, node) { - if (!bank->mod_usage || !bank->loses_context) + if (!BANK_USED(bank) || !bank->loses_context) continue; bank->power_mode = pwr_mode; @@ -1414,7 +1421,7 @@ void omap2_gpio_resume_after_idle(void) struct gpio_bank *bank; list_for_each_entry(bank, &omap_gpio_list, node) { - if (!bank->mod_usage || !bank->loses_context) + if (!BANK_USED(bank) || !bank->loses_context) continue; pm_runtime_get_sync(bank->dev); From fac7fa162a19100298d5d91359960037dc5bfca9 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Wed, 25 Sep 2013 02:36:54 +0200 Subject: [PATCH 2/2] gpio/omap: auto-setup a GPIO when used as an IRQ The OMAP GPIO controller HW requires a pin to be configured in GPIO input mode in order to operate as an interrupt input. Since drivers should not be aware of whether an interrupt pin is also a GPIO or not, the HW should be fully configured/enabled as an IRQ if a driver solely uses IRQ APIs such as request_irq(), and never calls any GPIO-related APIs. As such, add the missing HW setup to the OMAP GPIO controller's irq_chip driver. Since this bypasses the GPIO subsystem we have to ensure that another driver won't be able to request the same GPIO pin that is used as an IRQ and set its direction as output. Requesting the GPIO and setting its direction as input is allowed though. This fixes smsc911x ethernet support for tobi and igep OMAP3 boards and OMAP4 SDP SPI based ethernet that use a GPIO as an interrupt line. Cc: stable@vger.kernel.org Acked-by: Stephen Warren Tested-by: George Cherian Tested-by: Aaro Koskinen Tested-by: Lars Poeschel Reviewed-by: Kevin Hilman Tested-by: Kevin Hilman Acked-by: Santosh Shilimkar Acked-by: Tony Lindgren Signed-off-by: Javier Martinez Canillas Signed-off-by: Linus Walleij --- drivers/gpio/gpio-omap.c | 129 +++++++++++++++++++++++++-------------- 1 file changed, 83 insertions(+), 46 deletions(-) diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c index a4fe038d090e..89675f862308 100644 --- a/drivers/gpio/gpio-omap.c +++ b/drivers/gpio/gpio-omap.c @@ -424,6 +424,52 @@ static int _set_gpio_triggering(struct gpio_bank *bank, int gpio, return 0; } +static void _enable_gpio_module(struct gpio_bank *bank, unsigned offset) +{ + if (bank->regs->pinctrl) { + void __iomem *reg = bank->base + bank->regs->pinctrl; + + /* Claim the pin for MPU */ + __raw_writel(__raw_readl(reg) | (1 << offset), reg); + } + + if (bank->regs->ctrl && !BANK_USED(bank)) { + void __iomem *reg = bank->base + bank->regs->ctrl; + u32 ctrl; + + ctrl = __raw_readl(reg); + /* Module is enabled, clocks are not gated */ + ctrl &= ~GPIO_MOD_CTRL_BIT; + __raw_writel(ctrl, reg); + bank->context.ctrl = ctrl; + } +} + +static void _disable_gpio_module(struct gpio_bank *bank, unsigned offset) +{ + void __iomem *base = bank->base; + + if (bank->regs->wkup_en && + !LINE_USED(bank->mod_usage, offset) && + !LINE_USED(bank->irq_usage, offset)) { + /* Disable wake-up during idle for dynamic tick */ + _gpio_rmw(base, bank->regs->wkup_en, 1 << offset, 0); + bank->context.wake_en = + __raw_readl(bank->base + bank->regs->wkup_en); + } + + if (bank->regs->ctrl && !BANK_USED(bank)) { + void __iomem *reg = bank->base + bank->regs->ctrl; + u32 ctrl; + + ctrl = __raw_readl(reg); + /* Module is disabled, clocks are gated */ + ctrl |= GPIO_MOD_CTRL_BIT; + __raw_writel(ctrl, reg); + bank->context.ctrl = ctrl; + } +} + static int gpio_is_input(struct gpio_bank *bank, int mask) { void __iomem *reg = bank->base + bank->regs->direction; @@ -437,9 +483,10 @@ static int gpio_irq_type(struct irq_data *d, unsigned type) unsigned gpio = 0; int retval; unsigned long flags; + unsigned offset; - if (WARN_ON(!BANK_USED(bank))) - return -EINVAL; + if (!BANK_USED(bank)) + pm_runtime_get_sync(bank->dev); #ifdef CONFIG_ARCH_OMAP1 if (d->irq > IH_MPUIO_BASE) @@ -457,7 +504,16 @@ static int gpio_irq_type(struct irq_data *d, unsigned type) return -EINVAL; spin_lock_irqsave(&bank->lock, flags); - retval = _set_gpio_triggering(bank, GPIO_INDEX(bank, gpio), type); + offset = GPIO_INDEX(bank, gpio); + retval = _set_gpio_triggering(bank, offset, type); + if (!LINE_USED(bank->mod_usage, offset)) { + _enable_gpio_module(bank, offset); + _set_gpio_direction(bank, offset, 1); + } else if (!gpio_is_input(bank, 1 << offset)) { + spin_unlock_irqrestore(&bank->lock, flags); + return -EINVAL; + } + bank->irq_usage |= 1 << GPIO_INDEX(bank, gpio); spin_unlock_irqrestore(&bank->lock, flags); @@ -620,30 +676,14 @@ static int omap_gpio_request(struct gpio_chip *chip, unsigned offset) spin_lock_irqsave(&bank->lock, flags); /* Set trigger to none. You need to enable the desired trigger with - * request_irq() or set_irq_type(). + * request_irq() or set_irq_type(). Only do this if the IRQ line has + * not already been requested. */ - _set_gpio_triggering(bank, offset, IRQ_TYPE_NONE); - - if (bank->regs->pinctrl) { - void __iomem *reg = bank->base + bank->regs->pinctrl; - - /* Claim the pin for MPU */ - __raw_writel(__raw_readl(reg) | (1 << offset), reg); + if (!LINE_USED(bank->irq_usage, offset)) { + _set_gpio_triggering(bank, offset, IRQ_TYPE_NONE); + _enable_gpio_module(bank, offset); } - - if (bank->regs->ctrl && !BANK_USED(bank)) { - void __iomem *reg = bank->base + bank->regs->ctrl; - u32 ctrl; - - ctrl = __raw_readl(reg); - /* Module is enabled, clocks are not gated */ - ctrl &= ~GPIO_MOD_CTRL_BIT; - __raw_writel(ctrl, reg); - bank->context.ctrl = ctrl; - } - bank->mod_usage |= 1 << offset; - spin_unlock_irqrestore(&bank->lock, flags); return 0; @@ -652,31 +692,11 @@ static int omap_gpio_request(struct gpio_chip *chip, unsigned offset) static void omap_gpio_free(struct gpio_chip *chip, unsigned offset) { struct gpio_bank *bank = container_of(chip, struct gpio_bank, chip); - void __iomem *base = bank->base; unsigned long flags; spin_lock_irqsave(&bank->lock, flags); - - if (bank->regs->wkup_en) { - /* Disable wake-up during idle for dynamic tick */ - _gpio_rmw(base, bank->regs->wkup_en, 1 << offset, 0); - bank->context.wake_en = - __raw_readl(bank->base + bank->regs->wkup_en); - } - bank->mod_usage &= ~(1 << offset); - - if (bank->regs->ctrl && !BANK_USED(bank)) { - void __iomem *reg = bank->base + bank->regs->ctrl; - u32 ctrl; - - ctrl = __raw_readl(reg); - /* Module is disabled, clocks are gated */ - ctrl |= GPIO_MOD_CTRL_BIT; - __raw_writel(ctrl, reg); - bank->context.ctrl = ctrl; - } - + _disable_gpio_module(bank, offset); _reset_gpio(bank, bank->chip.base + offset); spin_unlock_irqrestore(&bank->lock, flags); @@ -778,8 +798,16 @@ static void gpio_irq_shutdown(struct irq_data *d) spin_lock_irqsave(&bank->lock, flags); bank->irq_usage &= ~(1 << offset); + _disable_gpio_module(bank, offset); _reset_gpio(bank, gpio); spin_unlock_irqrestore(&bank->lock, flags); + + /* + * If this is the last IRQ to be freed in the bank, + * disable the bank module. + */ + if (!BANK_USED(bank)) + pm_runtime_put(bank->dev); } static void gpio_ack_irq(struct irq_data *d) @@ -929,13 +957,22 @@ static int gpio_output(struct gpio_chip *chip, unsigned offset, int value) { struct gpio_bank *bank; unsigned long flags; + int retval = 0; bank = container_of(chip, struct gpio_bank, chip); spin_lock_irqsave(&bank->lock, flags); + + if (LINE_USED(bank->irq_usage, offset)) { + retval = -EINVAL; + goto exit; + } + bank->set_dataout(bank, offset, value); _set_gpio_direction(bank, offset, 0); + +exit: spin_unlock_irqrestore(&bank->lock, flags); - return 0; + return retval; } static int gpio_debounce(struct gpio_chip *chip, unsigned offset,