usb: Remove ehci_reset call from ehci_run

Remove the ehci_reset() call done in the ehci_run() routine of the
USB EHCI host controller driver and add an ehci_reset() call to the
probe processing of all EHCI platform drivers that do not already call
ehci_reset().

The call to ehci_reset() from ehci_run() was problematic for several
platform drivers, and unnecessary for others.  This change moves the
decision to call ehci_reset() at driver startup to the platform
driver code.

Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>

drivers/usb/host/ehci-au1xxx.c

@@ -23,6 +23,7 @@ static int au1xxx_ehci_setup(struct usb_hcd *hcd)
 	int ret = ehci_init(hcd);
 
 	ehci->need_io_watchdog = 0;
+	ehci_reset(ehci);
 	return ret;
 }
 

drivers/usb/host/ehci-hcd.c

@@ -677,22 +677,13 @@ static int ehci_init(struct usb_hcd *hcd)
 static int ehci_run (struct usb_hcd *hcd)
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
-	int			retval;
 	u32			temp;
 	u32			hcc_params;
 
 	hcd->uses_new_polling = 1;
 
 	/* EHCI spec section 4.1 */
-	/*
+
-	 * TDI driver does the ehci_reset in their reset callback.
-	 * Don't reset here, because configuration settings will
-	 * vanish.
-	 */
-	if (!ehci_is_TDI(ehci) && (retval = ehci_reset(ehci)) != 0) {
-		ehci_mem_cleanup(ehci);
-		return retval;
-	}
 	ehci_writel(ehci, ehci->periodic_dma, &ehci->regs->frame_list);
 	ehci_writel(ehci, (u32)ehci->async->qh_dma, &ehci->regs->async_next);
 

drivers/usb/host/ehci-octeon.c

@@ -155,6 +155,8 @@ static int ehci_octeon_drv_probe(struct platform_device *pdev)
 	/* cache this readonly data; minimize chip reads */
 	ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
 
+	ehci_reset(ehci);
+
 	ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
 	if (ret) {
 		dev_dbg(&pdev->dev, "failed to add hcd with err %d\n", ret);

drivers/usb/host/ehci-omap.c

@@ -228,6 +228,8 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev)
 	/* cache this readonly data; minimize chip reads */
 	omap_ehci->hcs_params = readl(&omap_ehci->caps->hcs_params);
 
+	ehci_reset(omap_ehci);
+
 	ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
 	if (ret) {
 		dev_err(dev, "failed to add hcd with err %d\n", ret);

drivers/usb/host/ehci-s5p.c

@@ -136,6 +136,8 @@ static int __devinit s5p_ehci_probe(struct platform_device *pdev)
 	/* cache this readonly data; minimize chip reads */
 	ehci->hcs_params = readl(&ehci->caps->hcs_params);
 
+	ehci_reset(ehci);
+
 	err = usb_add_hcd(hcd, irq, IRQF_SHARED);
 	if (err) {
 		dev_err(&pdev->dev, "Failed to add USB HCD\n");

drivers/usb/host/ehci-vt8500.c

@@ -132,6 +132,8 @@ static int vt8500_ehci_drv_probe(struct platform_device *pdev)
 
 	ehci_port_power(ehci, 1);
 
+	ehci_reset(ehci);
+
 	ret = usb_add_hcd(hcd, pdev->resource[1].start,
 			  IRQF_SHARED);
 	if (ret == 0) {

drivers/usb/host/ehci-w90x900.c

@@ -78,6 +78,8 @@ static int __devinit usb_w90x900_probe(const struct hc_driver *driver,
 	if (irq < 0)
 		goto err4;
 
+	ehci_reset(ehci);
+
 	retval = usb_add_hcd(hcd, irq, IRQF_SHARED);
 	if (retval != 0)
 		goto err4;