net: phy: at803x: simplify custom phy id matching

The at803x driver contains a function, at803x_match_phy_id(), which
tests whether the PHY ID matches the value passed, comparing phy_id
with phydev->phy_id and testing all bits that in the driver's mask.

This is the same test that is used to match the driver, with phy_id
replaced with the driver specified ID, phydev->drv->phy_id.

Hence, we already know the value of the bits being tested if we look
at phydev->drv->phy_id directly, and we do not require a complicated
test to check them. Test directly against phydev->drv->phy_id instead.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/phy/at803x.c

@@ -532,12 +532,6 @@ static int at8031_register_regulators(struct phy_device *phydev)
 	return 0;
 }
 
-static bool at803x_match_phy_id(struct phy_device *phydev, u32 phy_id)
-{
-	return (phydev->phy_id & phydev->drv->phy_id_mask)
-		== (phy_id & phydev->drv->phy_id_mask);
-}
-
 static int at803x_parse_dt(struct phy_device *phydev)
 {
 	struct device_node *node = phydev->mdio.dev.of_node;
@@ -602,8 +596,8 @@ static int at803x_parse_dt(struct phy_device *phydev)
 		 *   to the AR8030 so there might be a good chance it works on
 		 *   the AR8030 too.
 		 */
-		if (at803x_match_phy_id(phydev, ATH8030_PHY_ID) ||
-		    at803x_match_phy_id(phydev, ATH8035_PHY_ID)) {
+		if (phydev->drv->phy_id == ATH8030_PHY_ID ||
+		    phydev->drv->phy_id == ATH8035_PHY_ID) {
 			priv->clk_25m_reg &= AT8035_CLK_OUT_MASK;
 			priv->clk_25m_mask &= AT8035_CLK_OUT_MASK;
 		}
@@ -631,7 +625,7 @@ static int at803x_parse_dt(struct phy_device *phydev)
 	/* Only supported on AR8031/AR8033, the AR8030/AR8035 use strapping
 	 * options.
 	 */
-	if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
+	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
 		if (of_property_read_bool(node, "qca,keep-pll-enabled"))
 			priv->flags |= AT803X_KEEP_PLL_ENABLED;
 
@@ -676,7 +670,7 @@ static int at803x_probe(struct phy_device *phydev)
 	 * Switch to the copper page, as otherwise we read
 	 * the PHY capabilities from the fiber side.
 	 */
-	if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
+	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
 		phy_lock_mdio_bus(phydev);
 		ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
 		phy_unlock_mdio_bus(phydev);
@@ -820,7 +814,7 @@ static int at803x_config_init(struct phy_device *phydev)
 	if (ret < 0)
 		return ret;
 
-	if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
+	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
 		ret = at8031_pll_config(phydev);
 		if (ret < 0)
 			return ret;