ixgbe: Limit lowest interrupt rate for adaptive interrupt moderation to 12K

This patch updates the lowest limit for adaptive interrupt interrupt
moderation to roughly 12K interrupts per second.

The way I came about reaching 12K as the desired interrupt rate is by
testing with UDP flows.  Specifically I had a simple test that ran a
netperf UDP_STREAM test at varying sizes.  What I found was as the packet
sizes increased the performance fell steadily behind until we were only
able to receive at ~4Gb/s with a message size of 65507.  A bit of digging
found that we were dropping packets for the socket in the network stack,
and looking at things further what I found was I could solve it by increasing
the interrupt rate, or increasing the rmem_default/rmem_max.  What I found was
that when the interrupt coalescing resulted in more data being processed
per interrupt than could be stored in the socket buffer we started losing
packets and the performance dropped.  So I reached 12K based on the
following math.

rmem_default = 212992
skb->truesize = 2994
212992 / 2994 = 71.14 packets to fill the buffer

packet rate at 1514 packet size is 812744pps
71.14 / 812744 = 87.9us to fill socket buffer

From there it was just a matter of choosing the interrupt rate and
providing a bit of wiggle room which is why I decided to go with 12K
interrupts per second as that uses a value of 84us.

The data below is based on VM to VM over a direct assigned ixgbe interface.
The test run was:
	netperf -H <ip> -t UDP_STREAM"

Socket  Message  Elapsed      Messages                   CPU      Service
Size    Size     Time         Okay Errors   Throughput   Util     Demand
bytes   bytes    secs            #      #   10^6bits/sec % SS     us/KB
Before:
212992   65507   60.00     1100662      0     9613.4     10.89    0.557
212992           60.00      473474            4135.4     11.27    0.576

After:
212992   65507   60.00     1100413      0     9611.2     10.73    0.549
212992           60.00      974132            8508.3     11.69    0.598

Using bare metal the data is similar but not as dramatic as the throughput
increases from about 8.5Gb/s to 9.5Gb/s.

Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/ethernet/intel/ixgbe/ixgbe.h

@@ -539,8 +539,7 @@ struct hwmon_buff {
 #define IXGBE_MIN_RSC_ITR	24
 #define IXGBE_100K_ITR		40
 #define IXGBE_20K_ITR		200
-#define IXGBE_10K_ITR		400
-#define IXGBE_8K_ITR		500
+#define IXGBE_12K_ITR		336
 
 /* ixgbe_test_staterr - tests bits in Rx descriptor status and error fields */
 static inline __le32 ixgbe_test_staterr(union ixgbe_adv_rx_desc *rx_desc,

drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c

@@ -2286,7 +2286,7 @@ static int ixgbe_set_coalesce(struct net_device *netdev,
 		adapter->tx_itr_setting = ec->tx_coalesce_usecs;
 
 	if (adapter->tx_itr_setting == 1)
-		tx_itr_param = IXGBE_10K_ITR;
+		tx_itr_param = IXGBE_12K_ITR;
 	else
 		tx_itr_param = adapter->tx_itr_setting;
 

drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c

@@ -866,7 +866,7 @@ static int ixgbe_alloc_q_vector(struct ixgbe_adapter *adapter,
 	if (txr_count && !rxr_count) {
 		/* tx only vector */
 		if (adapter->tx_itr_setting == 1)
-			q_vector->itr = IXGBE_10K_ITR;
+			q_vector->itr = IXGBE_12K_ITR;
 		else
 			q_vector->itr = adapter->tx_itr_setting;
 	} else {

drivers/net/ethernet/intel/ixgbe/ixgbe_main.c

@@ -2261,7 +2261,7 @@ static void ixgbe_update_itr(struct ixgbe_q_vector *q_vector,
 	/* simple throttlerate management
 	 *   0-10MB/s   lowest (100000 ints/s)
 	 *  10-20MB/s   low    (20000 ints/s)
-	 *  20-1249MB/s bulk   (8000 ints/s)
+	 *  20-1249MB/s bulk   (12000 ints/s)
 	 */
 	/* what was last interrupt timeslice? */
 	timepassed_us = q_vector->itr >> 2;
@@ -2350,7 +2350,7 @@ static void ixgbe_set_itr(struct ixgbe_q_vector *q_vector)
 		new_itr = IXGBE_20K_ITR;
 		break;
 	case bulk_latency:
-		new_itr = IXGBE_8K_ITR;
+		new_itr = IXGBE_12K_ITR;
 		break;
 	default:
 		break;