dt-bindings:iio:adc:renesas,rcar-gyroadc: txt to yaml conversion.
This is a somewhat unusual device, in that it effectively does spi offload. That means that it doesn't act as a full SPI master, but supports some functionality. As such it supports a subset of specific SPI ADCs. There is potential for a future clash in bindings, but as these are simple devices hopefully that will not occur. One addition to this from testing it against existing dts files was to add a resets property. This is specified in arch/arm/boot/dts/r8a7791.dtsi If it's the dtsi that is wrong and not the binding doc, then we can fix that instead. Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Rob Herring <robh@kernel.org> Cc: Marek Vasut <marek.vasut+renesas@gmail.com> Link: https://lore.kernel.org/r/20201031184854.745828-31-jic23@kernel.org
This commit is contained in:
Jonathan Cameron
Родитель
58ff1b5197
Коммит
8c41245872
|
|
@ -1,98 +0,0 @@
|
|||
* Renesas R-Car GyroADC device driver
|
||||
|
||||
The GyroADC block is a reduced SPI block with up to 8 chipselect lines,
|
||||
which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs
|
||||
are sampled by the GyroADC block in a round-robin fashion and the result
|
||||
presented in the GyroADC registers.
|
||||
|
||||
Required properties:
|
||||
- compatible: Should be "<soc-specific>", "renesas,rcar-gyroadc".
|
||||
The <soc-specific> should be one of:
|
||||
renesas,r8a7791-gyroadc - for the GyroADC block present
|
||||
in r8a7791 SoC
|
||||
renesas,r8a7792-gyroadc - for the GyroADC with interrupt
|
||||
block present in r8a7792 SoC
|
||||
- reg: Address and length of the register set for the device
|
||||
- clocks: References to all the clocks specified in the clock-names
|
||||
property as specified in
|
||||
Documentation/devicetree/bindings/clock/clock-bindings.txt.
|
||||
- clock-names: Shall contain "fck". The "fck" is the GyroADC block clock.
|
||||
- power-domains: Must contain a reference to the PM domain, if available.
|
||||
- #address-cells: Should be <1> (setting for the subnodes) for all ADCs
|
||||
except for "fujitsu,mb88101a". Should be <0> (setting for
|
||||
only subnode) for "fujitsu,mb88101a".
|
||||
- #size-cells: Should be <0> (setting for the subnodes)
|
||||
|
||||
Sub-nodes:
|
||||
You must define subnode(s) which select the connected ADC type and reference
|
||||
voltage for the GyroADC channels.
|
||||
|
||||
Required properties for subnodes:
|
||||
- compatible: Should be either of:
|
||||
"fujitsu,mb88101a"
|
||||
- Fujitsu MB88101A compatible mode,
|
||||
12bit sampling, up to 4 channels can be sampled in
|
||||
round-robin fashion. One Fujitsu chip supplies four
|
||||
GyroADC channels with data as it contains four ADCs
|
||||
on the chip and thus for 4-channel operation, single
|
||||
MB88101A is required. The Cx chipselect lines of the
|
||||
MB88101A connect directly to two CHS lines of the
|
||||
GyroADC, no demuxer is required. The data out line
|
||||
of each MB88101A connects to a shared input pin of
|
||||
the GyroADC.
|
||||
"ti,adcs7476" or "ti,adc121" or "adi,ad7476"
|
||||
- TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode,
|
||||
15bit sampling, up to 8 channels can be sampled in
|
||||
round-robin fashion. One TI/ADI chip supplies single
|
||||
ADC channel with data, thus for 8-channel operation,
|
||||
8 chips are required. A 3:8 chipselect demuxer is
|
||||
required to connect the nCS line of the TI/ADI chips
|
||||
to the GyroADC, while MISO line of each TI/ADI ADC
|
||||
connects to a shared input pin of the GyroADC.
|
||||
"maxim,max1162" or "maxim,max11100"
|
||||
- Maxim MAX1162 / Maxim MAX11100 compatible mode,
|
||||
16bit sampling, up to 8 channels can be sampled in
|
||||
round-robin fashion. One Maxim chip supplies single
|
||||
ADC channel with data, thus for 8-channel operation,
|
||||
8 chips are required. A 3:8 chipselect demuxer is
|
||||
required to connect the nCS line of the MAX chips
|
||||
to the GyroADC, while MISO line of each Maxim ADC
|
||||
connects to a shared input pin of the GyroADC.
|
||||
- reg: Should be the number of the analog input. Should be present
|
||||
for all ADCs except "fujitsu,mb88101a".
|
||||
- vref-supply: Reference to the channel reference voltage regulator.
|
||||
|
||||
Example:
|
||||
vref_max1162: regulator-vref-max1162 {
|
||||
compatible = "regulator-fixed";
|
||||
|
||||
regulator-name = "MAX1162 Vref";
|
||||
regulator-min-microvolt = <4096000>;
|
||||
regulator-max-microvolt = <4096000>;
|
||||
};
|
||||
|
||||
adc@e6e54000 {
|
||||
compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc";
|
||||
reg = <0 0xe6e54000 0 64>;
|
||||
clocks = <&mstp9_clks R8A7791_CLK_GYROADC>;
|
||||
clock-names = "fck";
|
||||
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
|
||||
|
||||
pinctrl-0 = <&adc_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
adc@0 {
|
||||
reg = <0>;
|
||||
compatible = "maxim,max1162";
|
||||
vref-supply = <&vref_max1162>;
|
||||
};
|
||||
|
||||
adc@1 {
|
||||
reg = <1>;
|
||||
compatible = "maxim,max1162";
|
||||
vref-supply = <&vref_max1162>;
|
||||
};
|
||||
};
|
||||
|
|
@ -0,0 +1,143 @@
|
|||
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
|
||||
%YAML 1.2
|
||||
---
|
||||
$id: http://devicetree.org/schemas/iio/adc/renesas,rcar-gyroadc.yaml#
|
||||
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||||
|
||||
title: Renesas R-Car GyroADC
|
||||
|
||||
maintainers:
|
||||
- Marek Vasut <marek.vasut+renesas@gmail.com>
|
||||
|
||||
description: |
|
||||
The GyroADC block is a reduced SPI block with up to 8 chipselect lines,
|
||||
which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs
|
||||
are sampled by the GyroADC block in a round-robin fashion and the result
|
||||
presented in the GyroADC registers.
|
||||
The ADC bindings should match with that of the devices connected to a
|
||||
full featured SPI bus.
|
||||
|
||||
properties:
|
||||
compatible:
|
||||
items:
|
||||
- enum:
|
||||
- renesas,r8a7791-gyroadc
|
||||
- renesas,r8a7792-gyroadc
|
||||
- const: renesas,rcar-gyroadc
|
||||
|
||||
reg:
|
||||
maxItems: 1
|
||||
|
||||
clocks:
|
||||
maxItems: 1
|
||||
|
||||
clock-names:
|
||||
const: fck
|
||||
|
||||
power-domains: true
|
||||
|
||||
resets: true
|
||||
|
||||
"#address-cells":
|
||||
const: 1
|
||||
|
||||
"#size-cells":
|
||||
const: 0
|
||||
|
||||
additionalProperties: false
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- reg
|
||||
- clocks
|
||||
- clock-names
|
||||
- "#address-cells"
|
||||
- "#size-cells"
|
||||
|
||||
patternProperties:
|
||||
"@[0-7]$":
|
||||
type: object
|
||||
properties:
|
||||
compatible:
|
||||
description: |
|
||||
fujitsu,mb88101a
|
||||
- Fujitsu MB88101A compatible mode,
|
||||
12bit sampling, up to 4 channels can be sampled in round-robin
|
||||
fashion. One Fujitsu chip supplies four GyroADC channels with
|
||||
data as it contains four ADCs on the chip and thus for 4-channel
|
||||
operation, single MB88101A is required. The Cx chipselect lines
|
||||
of the MB88101A connect directly to two CHS lines of the GyroADC,
|
||||
no demuxer is required. The data out line of each MB88101A
|
||||
connects to a shared input pin of the GyroADC.
|
||||
ti,adcs7476 or ti,adc121 or adi,ad7476
|
||||
- TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode, 15bit
|
||||
sampling, up to 8 channels can be sampled in round-robin
|
||||
fashion. One TI/ADI chip supplies single ADC channel with data,
|
||||
thus for 8-channel operation, 8 chips are required.
|
||||
A 3:8 chipselect demuxer is required to connect the nCS line
|
||||
of the TI/ADI chips to the GyroADC, while MISO line of each
|
||||
TI/ADI ADC connects to a shared input pin of the GyroADC.
|
||||
maxim,max1162 or maxim,max11100
|
||||
- Maxim MAX1162 / Maxim MAX11100 compatible mode, 16bit sampling,
|
||||
up to 8 channels can be sampled in round-robin fashion. One
|
||||
Maxim chip supplies single ADC channel with data, thus for
|
||||
8-channel operation, 8 chips are required.
|
||||
A 3:8 chipselect demuxer is required to connect the nCS line
|
||||
of the MAX chips to the GyroADC, while MISO line of each Maxim
|
||||
ADC connects to a shared input pin of the GyroADC.
|
||||
enum:
|
||||
- adi,7476
|
||||
- fujitsu,mb88101a
|
||||
- maxim,max1162
|
||||
- maxim,max11100
|
||||
- ti,adcs7476
|
||||
- ti,adc121
|
||||
|
||||
reg:
|
||||
minimum: 0
|
||||
maximum: 7
|
||||
|
||||
vref-supply: true
|
||||
|
||||
additionalProperties: false
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- reg
|
||||
- vref-supply
|
||||
|
||||
examples:
|
||||
- |
|
||||
#include <dt-bindings/clock/r8a7791-clock.h>
|
||||
#include <dt-bindings/power/r8a7791-sysc.h>
|
||||
soc {
|
||||
#address-cells = <2>;
|
||||
#size-cells = <2>;
|
||||
|
||||
adc@e6e54000 {
|
||||
compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc";
|
||||
reg = <0 0xe6e54000 0 64>;
|
||||
clocks = <&mstp9_clks R8A7791_CLK_GYROADC>;
|
||||
clock-names = "fck";
|
||||
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
|
||||
|
||||
pinctrl-0 = <&adc_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
adc@0 {
|
||||
reg = <0>;
|
||||
compatible = "maxim,max1162";
|
||||
vref-supply = <&vref_max1162>;
|
||||
};
|
||||
|
||||
adc@1 {
|
||||
reg = <1>;
|
||||
compatible = "maxim,max1162";
|
||||
vref-supply = <&vref_max1162>;
|
||||
};
|
||||
};
|
||||
};
|
||||
...
|
||||
Загрузка…
Ссылка в новой задаче