kbuild: doc: replace arch/$(ARCH)/ with arch/$(SRCARCH)/
Precisely speaking, the arch directory is specified by $(SRCARCH),
not $(ARCH).
In old days, $(ARCH) actually matched to the arch directory because
32-bit and 64-bit were supported as separate architectures.
Most architectures (except arm/arm64) were unified like follows:
arch/i386, arch/x86_64 -> arch/x86
arch/sh, arch/sh64 -> arch/sh
arch/sparc, arch/sparc64 -> arch/sparc
To not break the user interface, commit 6752ed90da ("Kbuild: allow
arch/xxx to use a different source path") introduced SRCARCH to point
to the arch directory, still allowing to pass in the former ARCH=i386
or ARCH=x86_64.
Update the documents for preciseness, and add the explanation of SRCARCH.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
This commit is contained in:
Masahiro Yamada
Родитель
b044a535d9
Коммит
8c4d9b145b
|
|
@ -69,7 +69,7 @@ The Makefiles have five parts::
|
|||
|
||||
Makefile the top Makefile.
|
||||
.config the kernel configuration file.
|
||||
arch/$(ARCH)/Makefile the arch Makefile.
|
||||
arch/$(SRCARCH)/Makefile the arch Makefile.
|
||||
scripts/Makefile.* common rules etc. for all kbuild Makefiles.
|
||||
kbuild Makefiles exist in every subdirectory
|
||||
|
||||
|
|
@ -82,7 +82,7 @@ It builds these goals by recursively descending into the subdirectories of
|
|||
the kernel source tree.
|
||||
The list of subdirectories which are visited depends upon the kernel
|
||||
configuration. The top Makefile textually includes an arch Makefile
|
||||
with the name arch/$(ARCH)/Makefile. The arch Makefile supplies
|
||||
with the name arch/$(SRCARCH)/Makefile. The arch Makefile supplies
|
||||
architecture-specific information to the top Makefile.
|
||||
|
||||
Each subdirectory has a kbuild Makefile which carries out the commands
|
||||
|
|
@ -933,7 +933,7 @@ When "make clean" is executed, make will descend down in arch/x86/boot,
|
|||
and clean as usual. The Makefile located in arch/x86/boot/ may use
|
||||
the subdir- trick to descend further down.
|
||||
|
||||
Note 1: arch/$(ARCH)/Makefile cannot use "subdir-", because that file is
|
||||
Note 1: arch/$(SRCARCH)/Makefile cannot use "subdir-", because that file is
|
||||
included in the top level makefile, and the kbuild infrastructure
|
||||
is not operational at that point.
|
||||
|
||||
|
|
@ -946,9 +946,9 @@ be visited during "make clean".
|
|||
The top level Makefile sets up the environment and does the preparation,
|
||||
before starting to descend down in the individual directories.
|
||||
The top level makefile contains the generic part, whereas
|
||||
arch/$(ARCH)/Makefile contains what is required to set up kbuild
|
||||
arch/$(SRCARCH)/Makefile contains what is required to set up kbuild
|
||||
for said architecture.
|
||||
To do so, arch/$(ARCH)/Makefile sets up a number of variables and defines
|
||||
To do so, arch/$(SRCARCH)/Makefile sets up a number of variables and defines
|
||||
a few targets.
|
||||
|
||||
When kbuild executes, the following steps are followed (roughly):
|
||||
|
|
@ -956,14 +956,14 @@ When kbuild executes, the following steps are followed (roughly):
|
|||
1) Configuration of the kernel => produce .config
|
||||
2) Store kernel version in include/linux/version.h
|
||||
3) Updating all other prerequisites to the target prepare:
|
||||
- Additional prerequisites are specified in arch/$(ARCH)/Makefile
|
||||
- Additional prerequisites are specified in arch/$(SRCARCH)/Makefile
|
||||
4) Recursively descend down in all directories listed in
|
||||
init-* core* drivers-* net-* libs-* and build all targets.
|
||||
- The values of the above variables are expanded in arch/$(ARCH)/Makefile.
|
||||
- The values of the above variables are expanded in arch/$(SRCARCH)/Makefile.
|
||||
5) All object files are then linked and the resulting file vmlinux is
|
||||
located at the root of the obj tree.
|
||||
The very first objects linked are listed in head-y, assigned by
|
||||
arch/$(ARCH)/Makefile.
|
||||
arch/$(SRCARCH)/Makefile.
|
||||
6) Finally, the architecture-specific part does any required post processing
|
||||
and builds the final bootimage.
|
||||
- This includes building boot records
|
||||
|
|
@ -1169,7 +1169,7 @@ When kbuild executes, the following steps are followed (roughly):
|
|||
$(core-y), $(libs-y), $(drivers-y) and $(net-y).
|
||||
|
||||
The top level Makefile defines values for all generic directories,
|
||||
and arch/$(ARCH)/Makefile only adds architecture-specific
|
||||
and arch/$(SRCARCH)/Makefile only adds architecture-specific
|
||||
directories.
|
||||
|
||||
Example::
|
||||
|
|
@ -1189,15 +1189,15 @@ When kbuild executes, the following steps are followed (roughly):
|
|||
The actual goals are not standardized across architectures.
|
||||
|
||||
It is common to locate any additional processing in a boot/
|
||||
directory below arch/$(ARCH)/.
|
||||
directory below arch/$(SRCARCH)/.
|
||||
|
||||
Kbuild does not provide any smart way to support building a
|
||||
target specified in boot/. Therefore arch/$(ARCH)/Makefile shall
|
||||
target specified in boot/. Therefore arch/$(SRCARCH)/Makefile shall
|
||||
call make manually to build a target in boot/.
|
||||
|
||||
The recommended approach is to include shortcuts in
|
||||
arch/$(ARCH)/Makefile, and use the full path when calling down
|
||||
into the arch/$(ARCH)/boot/Makefile.
|
||||
arch/$(SRCARCH)/Makefile, and use the full path when calling down
|
||||
into the arch/$(SRCARCH)/boot/Makefile.
|
||||
|
||||
Example::
|
||||
|
||||
|
|
@ -1217,7 +1217,7 @@ When kbuild executes, the following steps are followed (roughly):
|
|||
|
||||
#arch/x86/Makefile
|
||||
define archhelp
|
||||
echo '* bzImage - Image (arch/$(ARCH)/boot/bzImage)'
|
||||
echo '* bzImage - Compressed kernel image (arch/x86/boot/bzImage)'
|
||||
endif
|
||||
|
||||
When make is executed without arguments, the first goal encountered
|
||||
|
|
@ -1332,7 +1332,7 @@ When kbuild executes, the following steps are followed (roughly):
|
|||
|
||||
objcopy
|
||||
Copy binary. Uses OBJCOPYFLAGS usually specified in
|
||||
arch/$(ARCH)/Makefile.
|
||||
arch/$(SRCARCH)/Makefile.
|
||||
OBJCOPYFLAGS_$@ may be used to set additional options.
|
||||
|
||||
gzip
|
||||
|
|
@ -1395,7 +1395,7 @@ When kbuild executes, the following steps are followed (roughly):
|
|||
--------------------------------
|
||||
|
||||
When the vmlinux image is built, the linker script
|
||||
arch/$(ARCH)/kernel/vmlinux.lds is used.
|
||||
arch/$(SRCARCH)/kernel/vmlinux.lds is used.
|
||||
The script is a preprocessed variant of the file vmlinux.lds.S
|
||||
located in the same directory.
|
||||
kbuild knows .lds files and includes a rule `*lds.S` -> `*lds`.
|
||||
|
|
@ -1405,9 +1405,6 @@ When kbuild executes, the following steps are followed (roughly):
|
|||
#arch/x86/kernel/Makefile
|
||||
extra-y := vmlinux.lds
|
||||
|
||||
#Makefile
|
||||
export CPPFLAGS_vmlinux.lds += -P -C -U$(ARCH)
|
||||
|
||||
The assignment to extra-y is used to tell kbuild to build the
|
||||
target vmlinux.lds.
|
||||
The assignment to $(CPPFLAGS_vmlinux.lds) tells kbuild to use the
|
||||
|
|
@ -1481,7 +1478,7 @@ See subsequent chapter for the syntax of the Kbuild file.
|
|||
|
||||
If an architecture uses a verbatim copy of a header from
|
||||
include/asm-generic then this is listed in the file
|
||||
arch/$(ARCH)/include/asm/Kbuild like this:
|
||||
arch/$(SRCARCH)/include/asm/Kbuild like this:
|
||||
|
||||
Example::
|
||||
|
||||
|
|
@ -1492,7 +1489,7 @@ See subsequent chapter for the syntax of the Kbuild file.
|
|||
During the prepare phase of the build a wrapper include
|
||||
file is generated in the directory::
|
||||
|
||||
arch/$(ARCH)/include/generated/asm
|
||||
arch/$(SRCARCH)/include/generated/asm
|
||||
|
||||
When a header is exported where the architecture uses
|
||||
the generic header a similar wrapper is generated as part
|
||||
|
|
@ -1527,8 +1524,8 @@ See subsequent chapter for the syntax of the Kbuild file.
|
|||
to define the minimum set of ASM headers that all architectures must have.
|
||||
|
||||
This works like optional generic-y. If a mandatory header is missing
|
||||
in arch/$(ARCH)/include/(uapi/)/asm, Kbuild will automatically generate
|
||||
a wrapper of the asm-generic one.
|
||||
in arch/$(SRCARCH)/include/(uapi/)/asm, Kbuild will automatically
|
||||
generate a wrapper of the asm-generic one.
|
||||
|
||||
9 Kbuild Variables
|
||||
==================
|
||||
|
|
@ -1564,6 +1561,16 @@ The top Makefile exports the following variables:
|
|||
|
||||
make ARCH=m68k ...
|
||||
|
||||
SRCARCH
|
||||
This variable specifies the directory in arch/ to build.
|
||||
|
||||
ARCH and SRCARCH may not necessarily match. A couple of arch
|
||||
directories are biarch, that is, a single `arch/*/` directory supports
|
||||
both 32-bit and 64-bit.
|
||||
|
||||
For example, you can pass in ARCH=i386, ARCH=x86_64, or ARCH=x86.
|
||||
For all of them, SRCARCH=x86 because arch/x86/ supports both i386 and
|
||||
x86_64.
|
||||
|
||||
INSTALL_PATH
|
||||
This variable defines a place for the arch Makefiles to install
|
||||
|
|
|
|||
|
|
@ -332,7 +332,7 @@ according to the following rule:
|
|||
There are two notable exceptions to this rule: larger
|
||||
subsystems have their own directory under include/, such as
|
||||
include/scsi; and architecture specific headers are located
|
||||
under arch/$(ARCH)/include/.
|
||||
under arch/$(SRCARCH)/include/.
|
||||
|
||||
4.1 Kernel Includes
|
||||
-------------------
|
||||
|
|
|
|||
Загрузка…
Ссылка в новой задаче