ata: pata: Convert pr_*(DRV_NAME ...) to pr_fmt/pr_<level>
Commit 40d69ba029
("pata_hpt{37x|3x2n}: use pr_*(DRV_NAME ...) instead of printk(KERN_* ...)")
used pr_<level>.
Add #define pr_fmt and remove DRV_NAME.
Increment driver version numbers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This commit is contained in:
Joe Perches
Jeff Garzik
Родитель
a17139b6f6
Коммит
8d7b1c70b3
|
|
@ -14,6 +14,7 @@
|
|||
* Look into engine reset on timeout errors. Should not be required.
|
||||
*/
|
||||
|
||||
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
|
||||
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/module.h>
|
||||
|
|
@ -25,7 +26,7 @@
|
|||
#include <linux/libata.h>
|
||||
|
||||
#define DRV_NAME "pata_hpt366"
|
||||
#define DRV_VERSION "0.6.10"
|
||||
#define DRV_VERSION "0.6.11"
|
||||
|
||||
struct hpt_clock {
|
||||
u8 xfer_mode;
|
||||
|
|
@ -160,8 +161,8 @@ static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr,
|
|||
|
||||
while (list[i] != NULL) {
|
||||
if (!strcmp(list[i], model_num)) {
|
||||
pr_warning(DRV_NAME ": %s is not supported for %s.\n",
|
||||
modestr, list[i]);
|
||||
pr_warn("%s is not supported for %s\n",
|
||||
modestr, list[i]);
|
||||
return 1;
|
||||
}
|
||||
i++;
|
||||
|
|
|
|||
|
|
@ -14,6 +14,8 @@
|
|||
* Look into engine reset on timeout errors. Should not be required.
|
||||
*/
|
||||
|
||||
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
|
||||
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/pci.h>
|
||||
|
|
@ -24,7 +26,7 @@
|
|||
#include <linux/libata.h>
|
||||
|
||||
#define DRV_NAME "pata_hpt37x"
|
||||
#define DRV_VERSION "0.6.22"
|
||||
#define DRV_VERSION "0.6.23"
|
||||
|
||||
struct hpt_clock {
|
||||
u8 xfer_speed;
|
||||
|
|
@ -229,8 +231,8 @@ static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr,
|
|||
|
||||
while (list[i] != NULL) {
|
||||
if (!strcmp(list[i], model_num)) {
|
||||
pr_warning(DRV_NAME ": %s is not supported for %s.\n",
|
||||
modestr, list[i]);
|
||||
pr_warn("%s is not supported for %s\n",
|
||||
modestr, list[i]);
|
||||
return 1;
|
||||
}
|
||||
i++;
|
||||
|
|
@ -863,8 +865,8 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|||
chip_table = &hpt372;
|
||||
break;
|
||||
default:
|
||||
pr_err(DRV_NAME ": Unknown HPT366 subtype, "
|
||||
"please report (%d).\n", rev);
|
||||
pr_err("Unknown HPT366 subtype, please report (%d)\n",
|
||||
rev);
|
||||
return -ENODEV;
|
||||
}
|
||||
break;
|
||||
|
|
@ -904,8 +906,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|||
*ppi = &info_hpt374_fn1;
|
||||
break;
|
||||
default:
|
||||
pr_err(DRV_NAME ": PCI table is bogus, please report (%d).\n",
|
||||
dev->device);
|
||||
pr_err("PCI table is bogus, please report (%d)\n", dev->device);
|
||||
return -ENODEV;
|
||||
}
|
||||
/* Ok so this is a chip we support */
|
||||
|
|
@ -953,7 +954,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|||
u8 sr;
|
||||
u32 total = 0;
|
||||
|
||||
pr_warning(DRV_NAME ": BIOS has not set timing clocks.\n");
|
||||
pr_warn("BIOS has not set timing clocks\n");
|
||||
|
||||
/* This is the process the HPT371 BIOS is reported to use */
|
||||
for (i = 0; i < 128; i++) {
|
||||
|
|
@ -1009,7 +1010,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|||
(f_high << 16) | f_low | 0x100);
|
||||
}
|
||||
if (adjust == 8) {
|
||||
pr_err(DRV_NAME ": DPLL did not stabilize!\n");
|
||||
pr_err("DPLL did not stabilize!\n");
|
||||
return -ENODEV;
|
||||
}
|
||||
if (dpll == 3)
|
||||
|
|
@ -1017,7 +1018,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|||
else
|
||||
private_data = (void *)hpt37x_timings_50;
|
||||
|
||||
pr_info(DRV_NAME ": bus clock %dMHz, using %dMHz DPLL.\n",
|
||||
pr_info("bus clock %dMHz, using %dMHz DPLL\n",
|
||||
MHz[clock_slot], MHz[dpll]);
|
||||
} else {
|
||||
private_data = (void *)chip_table->clocks[clock_slot];
|
||||
|
|
@ -1032,7 +1033,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|||
if (clock_slot < 2 && ppi[0] == &info_hpt370a)
|
||||
ppi[0] = &info_hpt370a_33;
|
||||
|
||||
pr_info(DRV_NAME ": %s using %dMHz bus clock.\n",
|
||||
pr_info("%s using %dMHz bus clock\n",
|
||||
chip_table->name, MHz[clock_slot]);
|
||||
}
|
||||
|
||||
|
|
|
|||
|
|
@ -15,6 +15,8 @@
|
|||
* Work out best PLL policy
|
||||
*/
|
||||
|
||||
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
|
||||
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/pci.h>
|
||||
|
|
@ -25,7 +27,7 @@
|
|||
#include <linux/libata.h>
|
||||
|
||||
#define DRV_NAME "pata_hpt3x2n"
|
||||
#define DRV_VERSION "0.3.14"
|
||||
#define DRV_VERSION "0.3.15"
|
||||
|
||||
enum {
|
||||
HPT_PCI_FAST = (1 << 31),
|
||||
|
|
@ -418,7 +420,7 @@ static int hpt3x2n_pci_clock(struct pci_dev *pdev)
|
|||
u16 sr;
|
||||
u32 total = 0;
|
||||
|
||||
pr_warning(DRV_NAME ": BIOS clock data not set.\n");
|
||||
pr_warn("BIOS clock data not set\n");
|
||||
|
||||
/* This is the process the HPT371 BIOS is reported to use */
|
||||
for (i = 0; i < 128; i++) {
|
||||
|
|
@ -528,8 +530,7 @@ hpt372n:
|
|||
ppi[0] = &info_hpt372n;
|
||||
break;
|
||||
default:
|
||||
pr_err(DRV_NAME ": PCI table is bogus, please report (%d).\n",
|
||||
dev->device);
|
||||
pr_err("PCI table is bogus, please report (%d)\n", dev->device);
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
|
|
@ -578,11 +579,11 @@ hpt372n:
|
|||
pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
|
||||
}
|
||||
if (adjust == 8) {
|
||||
pr_err(DRV_NAME ": DPLL did not stabilize!\n");
|
||||
pr_err("DPLL did not stabilize!\n");
|
||||
return -ENODEV;
|
||||
}
|
||||
|
||||
pr_info(DRV_NAME ": bus clock %dMHz, using 66MHz DPLL.\n", pci_mhz);
|
||||
pr_info("bus clock %dMHz, using 66MHz DPLL\n", pci_mhz);
|
||||
|
||||
/*
|
||||
* Set our private data up. We only need a few flags
|
||||
|
|
|
|||
Загрузка…
Ссылка в новой задаче