doc: Update stallwarn.txt to make causes more prominent
This commit rearranges the Documentation/RCU/stallwarn.txt file to put the list of issues that can cause RCU CPU stall warnings near the beginning of the document. Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit is contained in:
Paul E. McKenney
Родитель
b4553f0cfe
Коммит
8e2a439753
|
|
@ -1,9 +1,102 @@
|
|||
Using RCU's CPU Stall Detector
|
||||
|
||||
The rcu_cpu_stall_suppress module parameter enables RCU's CPU stall
|
||||
detector, which detects conditions that unduly delay RCU grace periods.
|
||||
This module parameter enables CPU stall detection by default, but
|
||||
may be overridden via boot-time parameter or at runtime via sysfs.
|
||||
This document first discusses what sorts of issues RCU's CPU stall
|
||||
detector can locate, and then discusses kernel parameters and Kconfig
|
||||
options that can be used to fine-tune the detector's operation. Finally,
|
||||
this document explains the stall detector's "splat" format.
|
||||
|
||||
|
||||
What Causes RCU CPU Stall Warnings?
|
||||
|
||||
So your kernel printed an RCU CPU stall warning. The next question is
|
||||
"What caused it?" The following problems can result in RCU CPU stall
|
||||
warnings:
|
||||
|
||||
o A CPU looping in an RCU read-side critical section.
|
||||
|
||||
o A CPU looping with interrupts disabled.
|
||||
|
||||
o A CPU looping with preemption disabled. This condition can
|
||||
result in RCU-sched stalls and, if ksoftirqd is in use, RCU-bh
|
||||
stalls.
|
||||
|
||||
o A CPU looping with bottom halves disabled. This condition can
|
||||
result in RCU-sched and RCU-bh stalls.
|
||||
|
||||
o For !CONFIG_PREEMPT kernels, a CPU looping anywhere in the
|
||||
kernel without invoking schedule(). Note that cond_resched()
|
||||
does not necessarily prevent RCU CPU stall warnings. Therefore,
|
||||
if the looping in the kernel is really expected and desirable
|
||||
behavior, you might need to replace some of the cond_resched()
|
||||
calls with calls to cond_resched_rcu_qs().
|
||||
|
||||
o Booting Linux using a console connection that is too slow to
|
||||
keep up with the boot-time console-message rate. For example,
|
||||
a 115Kbaud serial console can be -way- too slow to keep up
|
||||
with boot-time message rates, and will frequently result in
|
||||
RCU CPU stall warning messages. Especially if you have added
|
||||
debug printk()s.
|
||||
|
||||
o Anything that prevents RCU's grace-period kthreads from running.
|
||||
This can result in the "All QSes seen" console-log message.
|
||||
This message will include information on when the kthread last
|
||||
ran and how often it should be expected to run.
|
||||
|
||||
o A CPU-bound real-time task in a CONFIG_PREEMPT kernel, which might
|
||||
happen to preempt a low-priority task in the middle of an RCU
|
||||
read-side critical section. This is especially damaging if
|
||||
that low-priority task is not permitted to run on any other CPU,
|
||||
in which case the next RCU grace period can never complete, which
|
||||
will eventually cause the system to run out of memory and hang.
|
||||
While the system is in the process of running itself out of
|
||||
memory, you might see stall-warning messages.
|
||||
|
||||
o A CPU-bound real-time task in a CONFIG_PREEMPT_RT kernel that
|
||||
is running at a higher priority than the RCU softirq threads.
|
||||
This will prevent RCU callbacks from ever being invoked,
|
||||
and in a CONFIG_PREEMPT_RCU kernel will further prevent
|
||||
RCU grace periods from ever completing. Either way, the
|
||||
system will eventually run out of memory and hang. In the
|
||||
CONFIG_PREEMPT_RCU case, you might see stall-warning
|
||||
messages.
|
||||
|
||||
o A hardware or software issue shuts off the scheduler-clock
|
||||
interrupt on a CPU that is not in dyntick-idle mode. This
|
||||
problem really has happened, and seems to be most likely to
|
||||
result in RCU CPU stall warnings for CONFIG_NO_HZ_COMMON=n kernels.
|
||||
|
||||
o A bug in the RCU implementation.
|
||||
|
||||
o A hardware failure. This is quite unlikely, but has occurred
|
||||
at least once in real life. A CPU failed in a running system,
|
||||
becoming unresponsive, but not causing an immediate crash.
|
||||
This resulted in a series of RCU CPU stall warnings, eventually
|
||||
leading the realization that the CPU had failed.
|
||||
|
||||
The RCU, RCU-sched, RCU-bh, and RCU-tasks implementations have CPU stall
|
||||
warning. Note that SRCU does -not- have CPU stall warnings. Please note
|
||||
that RCU only detects CPU stalls when there is a grace period in progress.
|
||||
No grace period, no CPU stall warnings.
|
||||
|
||||
To diagnose the cause of the stall, inspect the stack traces.
|
||||
The offending function will usually be near the top of the stack.
|
||||
If you have a series of stall warnings from a single extended stall,
|
||||
comparing the stack traces can often help determine where the stall
|
||||
is occurring, which will usually be in the function nearest the top of
|
||||
that portion of the stack which remains the same from trace to trace.
|
||||
If you can reliably trigger the stall, ftrace can be quite helpful.
|
||||
|
||||
RCU bugs can often be debugged with the help of CONFIG_RCU_TRACE
|
||||
and with RCU's event tracing. For information on RCU's event tracing,
|
||||
see include/trace/events/rcu.h.
|
||||
|
||||
|
||||
Fine-Tuning the RCU CPU Stall Detector
|
||||
|
||||
The rcuupdate.rcu_cpu_stall_suppress module parameter disables RCU's
|
||||
CPU stall detector, which detects conditions that unduly delay RCU grace
|
||||
periods. This module parameter enables CPU stall detection by default,
|
||||
but may be overridden via boot-time parameter or at runtime via sysfs.
|
||||
The stall detector's idea of what constitutes "unduly delayed" is
|
||||
controlled by a set of kernel configuration variables and cpp macros:
|
||||
|
||||
|
|
@ -56,6 +149,9 @@ rcupdate.rcu_task_stall_timeout
|
|||
And continues with the output of sched_show_task() for each
|
||||
task stalling the current RCU-tasks grace period.
|
||||
|
||||
|
||||
Interpreting RCU's CPU Stall-Detector "Splats"
|
||||
|
||||
For non-RCU-tasks flavors of RCU, when a CPU detects that it is stalling,
|
||||
it will print a message similar to the following:
|
||||
|
||||
|
|
@ -178,89 +274,3 @@ grace period is in flight.
|
|||
|
||||
It is entirely possible to see stall warnings from normal and from
|
||||
expedited grace periods at about the same time from the same run.
|
||||
|
||||
|
||||
What Causes RCU CPU Stall Warnings?
|
||||
|
||||
So your kernel printed an RCU CPU stall warning. The next question is
|
||||
"What caused it?" The following problems can result in RCU CPU stall
|
||||
warnings:
|
||||
|
||||
o A CPU looping in an RCU read-side critical section.
|
||||
|
||||
o A CPU looping with interrupts disabled. This condition can
|
||||
result in RCU-sched and RCU-bh stalls.
|
||||
|
||||
o A CPU looping with preemption disabled. This condition can
|
||||
result in RCU-sched stalls and, if ksoftirqd is in use, RCU-bh
|
||||
stalls.
|
||||
|
||||
o A CPU looping with bottom halves disabled. This condition can
|
||||
result in RCU-sched and RCU-bh stalls.
|
||||
|
||||
o For !CONFIG_PREEMPT kernels, a CPU looping anywhere in the
|
||||
kernel without invoking schedule(). Note that cond_resched()
|
||||
does not necessarily prevent RCU CPU stall warnings. Therefore,
|
||||
if the looping in the kernel is really expected and desirable
|
||||
behavior, you might need to replace some of the cond_resched()
|
||||
calls with calls to cond_resched_rcu_qs().
|
||||
|
||||
o Booting Linux using a console connection that is too slow to
|
||||
keep up with the boot-time console-message rate. For example,
|
||||
a 115Kbaud serial console can be -way- too slow to keep up
|
||||
with boot-time message rates, and will frequently result in
|
||||
RCU CPU stall warning messages. Especially if you have added
|
||||
debug printk()s.
|
||||
|
||||
o Anything that prevents RCU's grace-period kthreads from running.
|
||||
This can result in the "All QSes seen" console-log message.
|
||||
This message will include information on when the kthread last
|
||||
ran and how often it should be expected to run.
|
||||
|
||||
o A CPU-bound real-time task in a CONFIG_PREEMPT kernel, which might
|
||||
happen to preempt a low-priority task in the middle of an RCU
|
||||
read-side critical section. This is especially damaging if
|
||||
that low-priority task is not permitted to run on any other CPU,
|
||||
in which case the next RCU grace period can never complete, which
|
||||
will eventually cause the system to run out of memory and hang.
|
||||
While the system is in the process of running itself out of
|
||||
memory, you might see stall-warning messages.
|
||||
|
||||
o A CPU-bound real-time task in a CONFIG_PREEMPT_RT kernel that
|
||||
is running at a higher priority than the RCU softirq threads.
|
||||
This will prevent RCU callbacks from ever being invoked,
|
||||
and in a CONFIG_PREEMPT_RCU kernel will further prevent
|
||||
RCU grace periods from ever completing. Either way, the
|
||||
system will eventually run out of memory and hang. In the
|
||||
CONFIG_PREEMPT_RCU case, you might see stall-warning
|
||||
messages.
|
||||
|
||||
o A hardware or software issue shuts off the scheduler-clock
|
||||
interrupt on a CPU that is not in dyntick-idle mode. This
|
||||
problem really has happened, and seems to be most likely to
|
||||
result in RCU CPU stall warnings for CONFIG_NO_HZ_COMMON=n kernels.
|
||||
|
||||
o A bug in the RCU implementation.
|
||||
|
||||
o A hardware failure. This is quite unlikely, but has occurred
|
||||
at least once in real life. A CPU failed in a running system,
|
||||
becoming unresponsive, but not causing an immediate crash.
|
||||
This resulted in a series of RCU CPU stall warnings, eventually
|
||||
leading the realization that the CPU had failed.
|
||||
|
||||
The RCU, RCU-sched, RCU-bh, and RCU-tasks implementations have CPU stall
|
||||
warning. Note that SRCU does -not- have CPU stall warnings. Please note
|
||||
that RCU only detects CPU stalls when there is a grace period in progress.
|
||||
No grace period, no CPU stall warnings.
|
||||
|
||||
To diagnose the cause of the stall, inspect the stack traces.
|
||||
The offending function will usually be near the top of the stack.
|
||||
If you have a series of stall warnings from a single extended stall,
|
||||
comparing the stack traces can often help determine where the stall
|
||||
is occurring, which will usually be in the function nearest the top of
|
||||
that portion of the stack which remains the same from trace to trace.
|
||||
If you can reliably trigger the stall, ftrace can be quite helpful.
|
||||
|
||||
RCU bugs can often be debugged with the help of CONFIG_RCU_TRACE
|
||||
and with RCU's event tracing. For information on RCU's event tracing,
|
||||
see include/trace/events/rcu.h.
|
||||
|
|
|
|||
Загрузка…
Ссылка в новой задаче