scsi: dtc: remove from tree
The driver has not seen any maintainer activity or other work that wasn't tree wide conversion or clenaups in the entire history of the git tree. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinicke <hare@suse.de> Acked-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This commit is contained in:
Christoph Hellwig
Martin K. Petersen
Родитель
f95819a09c
Коммит
92efbb8500
|
|
@ -1,43 +0,0 @@
|
|||
README file for the Linux DTC3180/3280 scsi driver.
|
||||
by Ray Van Tassle (rayvt@comm.mot.com) March 1996
|
||||
Based on the generic & core NCR5380 code by Drew Eckhard
|
||||
|
||||
SCSI device driver for the DTC 3180/3280.
|
||||
Data Technology Corp---a division of Qume.
|
||||
|
||||
The 3280 has a standard floppy interface.
|
||||
|
||||
The 3180 does not. Otherwise, they are identical.
|
||||
|
||||
The DTC3x80 does not support DMA but it does have Pseudo-DMA which is
|
||||
supported by the driver.
|
||||
|
||||
Its DTC406 scsi chip is supposedly compatible with the NCR 53C400.
|
||||
It is memory mapped, uses an IRQ, but no dma or io-port. There is
|
||||
internal DMA, between SCSI bus and an on-chip 128-byte buffer. Double
|
||||
buffering is done automagically by the chip. Data is transferred
|
||||
between the on-chip buffer and CPU/RAM via memory moves.
|
||||
|
||||
The driver detects the possible memory addresses (jumper selectable):
|
||||
CC00, DC00, C800, and D800
|
||||
The possible IRQ's (jumper selectable) are:
|
||||
IRQ 10, 11, 12, 15
|
||||
Parity is supported by the chip, but not by this driver.
|
||||
Information can be obtained from /proc/scsi/dtc3c80/N.
|
||||
|
||||
Note on interrupts:
|
||||
|
||||
The documentation says that it can be set to interrupt whenever the
|
||||
on-chip buffer needs CPU attention. I couldn't get this to work. So
|
||||
the driver polls for data-ready in the pseudo-DMA transfer routine.
|
||||
The interrupt support routines in the NCR3280.c core modules handle
|
||||
scsi disconnect/reconnect, and this (mostly) works. However..... I
|
||||
have tested it with 4 totally different hard drives (both SCSI-1 and
|
||||
SCSI-2), and one CDROM drive. Interrupts works great for all but one
|
||||
specific hard drive. For this one, the driver will eventually hang in
|
||||
the transfer state. I have tested with: "dd bs=4k count=2k
|
||||
of=/dev/null if=/dev/sdb". It reads ok for a while, then hangs.
|
||||
After beating my head against this for a couple of weeks, getting
|
||||
nowhere, I give up. So.....This driver does NOT use interrupts, even
|
||||
if you have the card jumpered to an IRQ. Probably nobody will ever
|
||||
care.
|
||||
|
|
@ -34,9 +34,6 @@ parameters may be changed at runtime by the command
|
|||
See drivers/scsi/BusLogic.c, comment before function
|
||||
BusLogic_ParseDriverOptions().
|
||||
|
||||
dtc3181e= [HW,SCSI]
|
||||
See Documentation/scsi/g_NCR5380.txt.
|
||||
|
||||
eata= [HW,SCSI]
|
||||
|
||||
fdomain= [HW,SCSI]
|
||||
|
|
|
|||
|
|
@ -8042,13 +8042,11 @@ M: Michael Schmitz <schmitzmic@gmail.com>
|
|||
L: linux-scsi@vger.kernel.org
|
||||
S: Maintained
|
||||
F: Documentation/scsi/g_NCR5380.txt
|
||||
F: Documentation/scsi/dtc3x80.txt
|
||||
F: drivers/scsi/NCR5380.*
|
||||
F: drivers/scsi/arm/cumana_1.c
|
||||
F: drivers/scsi/arm/oak.c
|
||||
F: drivers/scsi/atari_scsi.*
|
||||
F: drivers/scsi/dmx3191d.c
|
||||
F: drivers/scsi/dtc.*
|
||||
F: drivers/scsi/g_NCR5380.*
|
||||
F: drivers/scsi/g_NCR5380_mmio.c
|
||||
F: drivers/scsi/mac_scsi.*
|
||||
|
|
|
|||
|
|
@ -637,20 +637,6 @@ config SCSI_DMX3191D
|
|||
To compile this driver as a module, choose M here: the
|
||||
module will be called dmx3191d.
|
||||
|
||||
config SCSI_DTC3280
|
||||
tristate "DTC3180/3280 SCSI support"
|
||||
depends on ISA && SCSI
|
||||
select SCSI_SPI_ATTRS
|
||||
select CHECK_SIGNATURE
|
||||
help
|
||||
This is support for DTC 3180/3280 SCSI Host Adapters. Please read
|
||||
the SCSI-HOWTO, available from
|
||||
<http://www.tldp.org/docs.html#howto>, and the file
|
||||
<file:Documentation/scsi/dtc3x80.txt>.
|
||||
|
||||
To compile this driver as a module, choose M here: the
|
||||
module will be called dtc.
|
||||
|
||||
config SCSI_EATA
|
||||
tristate "EATA ISA/EISA/PCI (DPT and generic EATA/DMA-compliant boards) support"
|
||||
depends on (ISA || EISA || PCI) && SCSI && ISA_DMA_API
|
||||
|
|
|
|||
|
|
@ -90,7 +90,6 @@ obj-$(CONFIG_SCSI_CHELSIO_FCOE) += csiostor/
|
|||
obj-$(CONFIG_SCSI_DMX3191D) += dmx3191d.o
|
||||
obj-$(CONFIG_SCSI_HPSA) += hpsa.o
|
||||
obj-$(CONFIG_SCSI_SMARTPQI) += smartpqi/
|
||||
obj-$(CONFIG_SCSI_DTC3280) += dtc.o
|
||||
obj-$(CONFIG_SCSI_SYM53C8XX_2) += sym53c8xx_2/
|
||||
obj-$(CONFIG_SCSI_ZALON) += zalon7xx.o
|
||||
obj-$(CONFIG_SCSI_EATA_PIO) += eata_pio.o
|
||||
|
|
|
|||
|
|
@ -1,447 +0,0 @@
|
|||
/*
|
||||
* DTC 3180/3280 driver, by
|
||||
* Ray Van Tassle rayvt@comm.mot.com
|
||||
*
|
||||
* taken from ...
|
||||
* Trantor T128/T128F/T228 driver by...
|
||||
*
|
||||
* Drew Eckhardt
|
||||
* Visionary Computing
|
||||
* (Unix and Linux consulting and custom programming)
|
||||
* drew@colorado.edu
|
||||
* +1 (303) 440-4894
|
||||
*/
|
||||
|
||||
/*
|
||||
* The card is detected and initialized in one of several ways :
|
||||
* 1. Autoprobe (default) - since the board is memory mapped,
|
||||
* a BIOS signature is scanned for to locate the registers.
|
||||
* An interrupt is triggered to autoprobe for the interrupt
|
||||
* line.
|
||||
*
|
||||
* 2. With command line overrides - dtc=address,irq may be
|
||||
* used on the LILO command line to override the defaults.
|
||||
*
|
||||
*/
|
||||
|
||||
/*----------------------------------------------------------------*/
|
||||
/* the following will set the monitor border color (useful to find
|
||||
where something crashed or gets stuck at */
|
||||
/* 1 = blue
|
||||
2 = green
|
||||
3 = cyan
|
||||
4 = red
|
||||
5 = magenta
|
||||
6 = yellow
|
||||
7 = white
|
||||
*/
|
||||
#if 0
|
||||
#define rtrc(i) {inb(0x3da); outb(0x31, 0x3c0); outb((i), 0x3c0);}
|
||||
#else
|
||||
#define rtrc(i) {}
|
||||
#endif
|
||||
|
||||
|
||||
#include <linux/module.h>
|
||||
#include <linux/blkdev.h>
|
||||
#include <linux/string.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/interrupt.h>
|
||||
#include <linux/io.h>
|
||||
#include <scsi/scsi_host.h>
|
||||
|
||||
#include "dtc.h"
|
||||
#include "NCR5380.h"
|
||||
|
||||
/*
|
||||
* The DTC3180 & 3280 boards are memory mapped.
|
||||
*
|
||||
*/
|
||||
|
||||
/*
|
||||
*/
|
||||
/* Offset from DTC_5380_OFFSET */
|
||||
#define DTC_CONTROL_REG 0x100 /* rw */
|
||||
#define D_CR_ACCESS 0x80 /* ro set=can access 3280 registers */
|
||||
#define CSR_DIR_READ 0x40 /* rw direction, 1 = read 0 = write */
|
||||
|
||||
#define CSR_RESET 0x80 /* wo Resets 53c400 */
|
||||
#define CSR_5380_REG 0x80 /* ro 5380 registers can be accessed */
|
||||
#define CSR_TRANS_DIR 0x40 /* rw Data transfer direction */
|
||||
#define CSR_SCSI_BUFF_INTR 0x20 /* rw Enable int on transfer ready */
|
||||
#define CSR_5380_INTR 0x10 /* rw Enable 5380 interrupts */
|
||||
#define CSR_SHARED_INTR 0x08 /* rw Interrupt sharing */
|
||||
#define CSR_HOST_BUF_NOT_RDY 0x04 /* ro Host buffer not ready */
|
||||
#define CSR_SCSI_BUF_RDY 0x02 /* ro SCSI buffer ready */
|
||||
#define CSR_GATED_5380_IRQ 0x01 /* ro Last block xferred */
|
||||
#define CSR_INT_BASE (CSR_SCSI_BUFF_INTR | CSR_5380_INTR)
|
||||
|
||||
|
||||
#define DTC_BLK_CNT 0x101 /* rw
|
||||
* # of 128-byte blocks to transfer */
|
||||
|
||||
|
||||
#define D_CR_ACCESS 0x80 /* ro set=can access 3280 registers */
|
||||
|
||||
#define DTC_SWITCH_REG 0x3982 /* ro - DIP switches */
|
||||
#define DTC_RESUME_XFER 0x3982 /* wo - resume data xfer
|
||||
* after disconnect/reconnect*/
|
||||
|
||||
#define DTC_5380_OFFSET 0x3880 /* 8 registers here, see NCR5380.h */
|
||||
|
||||
/*!!!! for dtc, it's a 128 byte buffer at 3900 !!! */
|
||||
#define DTC_DATA_BUF 0x3900 /* rw 128 bytes long */
|
||||
|
||||
static struct override {
|
||||
unsigned int address;
|
||||
int irq;
|
||||
} overrides
|
||||
#ifdef OVERRIDE
|
||||
[] __initdata = OVERRIDE;
|
||||
#else
|
||||
[4] __initdata = {
|
||||
{ 0, IRQ_AUTO }, { 0, IRQ_AUTO }, { 0, IRQ_AUTO }, { 0, IRQ_AUTO }
|
||||
};
|
||||
#endif
|
||||
|
||||
#define NO_OVERRIDES ARRAY_SIZE(overrides)
|
||||
|
||||
static struct base {
|
||||
unsigned long address;
|
||||
int noauto;
|
||||
} bases[] __initdata = {
|
||||
{ 0xcc000, 0 },
|
||||
{ 0xc8000, 0 },
|
||||
{ 0xdc000, 0 },
|
||||
{ 0xd8000, 0 }
|
||||
};
|
||||
|
||||
#define NO_BASES ARRAY_SIZE(bases)
|
||||
|
||||
static const struct signature {
|
||||
const char *string;
|
||||
int offset;
|
||||
} signatures[] = {
|
||||
{"DATA TECHNOLOGY CORPORATION BIOS", 0x25},
|
||||
};
|
||||
|
||||
#define NO_SIGNATURES ARRAY_SIZE(signatures)
|
||||
|
||||
#ifndef MODULE
|
||||
/*
|
||||
* Function : dtc_setup(char *str, int *ints)
|
||||
*
|
||||
* Purpose : LILO command line initialization of the overrides array,
|
||||
*
|
||||
* Inputs : str - unused, ints - array of integer parameters with ints[0]
|
||||
* equal to the number of ints.
|
||||
*
|
||||
*/
|
||||
|
||||
static int __init dtc_setup(char *str)
|
||||
{
|
||||
static int commandline_current;
|
||||
int i;
|
||||
int ints[10];
|
||||
|
||||
get_options(str, ARRAY_SIZE(ints), ints);
|
||||
if (ints[0] != 2)
|
||||
printk("dtc_setup: usage dtc=address,irq\n");
|
||||
else if (commandline_current < NO_OVERRIDES) {
|
||||
overrides[commandline_current].address = ints[1];
|
||||
overrides[commandline_current].irq = ints[2];
|
||||
for (i = 0; i < NO_BASES; ++i)
|
||||
if (bases[i].address == ints[1]) {
|
||||
bases[i].noauto = 1;
|
||||
break;
|
||||
}
|
||||
++commandline_current;
|
||||
}
|
||||
return 1;
|
||||
}
|
||||
|
||||
__setup("dtc=", dtc_setup);
|
||||
#endif
|
||||
|
||||
/*
|
||||
* Function : int dtc_detect(struct scsi_host_template * tpnt)
|
||||
*
|
||||
* Purpose : detects and initializes DTC 3180/3280 controllers
|
||||
* that were autoprobed, overridden on the LILO command line,
|
||||
* or specified at compile time.
|
||||
*
|
||||
* Inputs : tpnt - template for this SCSI adapter.
|
||||
*
|
||||
* Returns : 1 if a host adapter was found, 0 if not.
|
||||
*
|
||||
*/
|
||||
|
||||
static int __init dtc_detect(struct scsi_host_template * tpnt)
|
||||
{
|
||||
static int current_override, current_base;
|
||||
struct Scsi_Host *instance;
|
||||
unsigned int addr;
|
||||
void __iomem *base;
|
||||
int sig, count;
|
||||
|
||||
for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
|
||||
addr = 0;
|
||||
base = NULL;
|
||||
|
||||
if (overrides[current_override].address) {
|
||||
addr = overrides[current_override].address;
|
||||
base = ioremap(addr, 0x2000);
|
||||
if (!base)
|
||||
addr = 0;
|
||||
} else
|
||||
for (; !addr && (current_base < NO_BASES); ++current_base) {
|
||||
dprintk(NDEBUG_INIT, "dtc: probing address 0x%08x\n",
|
||||
(unsigned int)bases[current_base].address);
|
||||
if (bases[current_base].noauto)
|
||||
continue;
|
||||
base = ioremap(bases[current_base].address, 0x2000);
|
||||
if (!base)
|
||||
continue;
|
||||
for (sig = 0; sig < NO_SIGNATURES; ++sig) {
|
||||
if (check_signature(base + signatures[sig].offset, signatures[sig].string, strlen(signatures[sig].string))) {
|
||||
addr = bases[current_base].address;
|
||||
dprintk(NDEBUG_INIT, "dtc: detected board\n");
|
||||
goto found;
|
||||
}
|
||||
}
|
||||
iounmap(base);
|
||||
}
|
||||
|
||||
dprintk(NDEBUG_INIT, "dtc: addr = 0x%08x\n", addr);
|
||||
|
||||
if (!addr)
|
||||
break;
|
||||
|
||||
found:
|
||||
instance = scsi_register(tpnt, sizeof(struct NCR5380_hostdata));
|
||||
if (instance == NULL)
|
||||
goto out_unmap;
|
||||
|
||||
instance->base = addr;
|
||||
((struct NCR5380_hostdata *)(instance)->hostdata)->base = base;
|
||||
|
||||
if (NCR5380_init(instance, FLAG_LATE_DMA_SETUP))
|
||||
goto out_unregister;
|
||||
|
||||
NCR5380_maybe_reset_bus(instance);
|
||||
|
||||
NCR5380_write(DTC_CONTROL_REG, CSR_5380_INTR); /* Enable int's */
|
||||
if (overrides[current_override].irq != IRQ_AUTO)
|
||||
instance->irq = overrides[current_override].irq;
|
||||
else
|
||||
instance->irq = NCR5380_probe_irq(instance, DTC_IRQS);
|
||||
|
||||
/* Compatibility with documented NCR5380 kernel parameters */
|
||||
if (instance->irq == 255)
|
||||
instance->irq = NO_IRQ;
|
||||
|
||||
/* With interrupts enabled, it will sometimes hang when doing heavy
|
||||
* reads. So better not enable them until I finger it out. */
|
||||
instance->irq = NO_IRQ;
|
||||
|
||||
if (instance->irq != NO_IRQ)
|
||||
if (request_irq(instance->irq, dtc_intr, 0,
|
||||
"dtc", instance)) {
|
||||
printk(KERN_ERR "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq);
|
||||
instance->irq = NO_IRQ;
|
||||
}
|
||||
|
||||
if (instance->irq == NO_IRQ) {
|
||||
printk(KERN_WARNING "scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
|
||||
printk(KERN_WARNING "scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
|
||||
}
|
||||
|
||||
dprintk(NDEBUG_INIT, "scsi%d : irq = %d\n",
|
||||
instance->host_no, instance->irq);
|
||||
|
||||
++current_override;
|
||||
++count;
|
||||
}
|
||||
return count;
|
||||
|
||||
out_unregister:
|
||||
scsi_unregister(instance);
|
||||
out_unmap:
|
||||
iounmap(base);
|
||||
return count;
|
||||
}
|
||||
|
||||
/*
|
||||
* Function : int dtc_biosparam(Disk * disk, struct block_device *dev, int *ip)
|
||||
*
|
||||
* Purpose : Generates a BIOS / DOS compatible H-C-S mapping for
|
||||
* the specified device / size.
|
||||
*
|
||||
* Inputs : size = size of device in sectors (512 bytes), dev = block device
|
||||
* major / minor, ip[] = {heads, sectors, cylinders}
|
||||
*
|
||||
* Returns : always 0 (success), initializes ip
|
||||
*
|
||||
*/
|
||||
|
||||
/*
|
||||
* XXX Most SCSI boards use this mapping, I could be incorrect. Some one
|
||||
* using hard disks on a trantor should verify that this mapping corresponds
|
||||
* to that used by the BIOS / ASPI driver by running the linux fdisk program
|
||||
* and matching the H_C_S coordinates to what DOS uses.
|
||||
*/
|
||||
|
||||
static int dtc_biosparam(struct scsi_device *sdev, struct block_device *dev,
|
||||
sector_t capacity, int *ip)
|
||||
{
|
||||
int size = capacity;
|
||||
|
||||
ip[0] = 64;
|
||||
ip[1] = 32;
|
||||
ip[2] = size >> 11;
|
||||
return 0;
|
||||
}
|
||||
|
||||
|
||||
/****************************************************************
|
||||
* Function : int NCR5380_pread (struct Scsi_Host *instance,
|
||||
* unsigned char *dst, int len)
|
||||
*
|
||||
* Purpose : Fast 5380 pseudo-dma read function, reads len bytes to
|
||||
* dst
|
||||
*
|
||||
* Inputs : dst = destination, len = length in bytes
|
||||
*
|
||||
* Returns : 0 on success, non zero on a failure such as a watchdog
|
||||
* timeout.
|
||||
*/
|
||||
|
||||
static inline int dtc_pread(struct Scsi_Host *instance,
|
||||
unsigned char *dst, int len)
|
||||
{
|
||||
unsigned char *d = dst;
|
||||
int i; /* For counting time spent in the poll-loop */
|
||||
struct NCR5380_hostdata *hostdata = shost_priv(instance);
|
||||
|
||||
i = 0;
|
||||
if (instance->irq == NO_IRQ)
|
||||
NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ);
|
||||
else
|
||||
NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ | CSR_INT_BASE);
|
||||
NCR5380_write(DTC_BLK_CNT, len >> 7); /* Block count */
|
||||
rtrc(1);
|
||||
while (len > 0) {
|
||||
rtrc(2);
|
||||
while (NCR5380_read(DTC_CONTROL_REG) & CSR_HOST_BUF_NOT_RDY)
|
||||
++i;
|
||||
rtrc(3);
|
||||
memcpy_fromio(d, hostdata->base + DTC_DATA_BUF, 128);
|
||||
d += 128;
|
||||
len -= 128;
|
||||
rtrc(7);
|
||||
/*** with int's on, it sometimes hangs after here.
|
||||
* Looks like something makes HBNR go away. */
|
||||
}
|
||||
rtrc(4);
|
||||
while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
|
||||
++i;
|
||||
rtrc(0);
|
||||
return (0);
|
||||
}
|
||||
|
||||
/****************************************************************
|
||||
* Function : int NCR5380_pwrite (struct Scsi_Host *instance,
|
||||
* unsigned char *src, int len)
|
||||
*
|
||||
* Purpose : Fast 5380 pseudo-dma write function, transfers len bytes from
|
||||
* src
|
||||
*
|
||||
* Inputs : src = source, len = length in bytes
|
||||
*
|
||||
* Returns : 0 on success, non zero on a failure such as a watchdog
|
||||
* timeout.
|
||||
*/
|
||||
|
||||
static inline int dtc_pwrite(struct Scsi_Host *instance,
|
||||
unsigned char *src, int len)
|
||||
{
|
||||
int i;
|
||||
struct NCR5380_hostdata *hostdata = shost_priv(instance);
|
||||
|
||||
if (instance->irq == NO_IRQ)
|
||||
NCR5380_write(DTC_CONTROL_REG, 0);
|
||||
else
|
||||
NCR5380_write(DTC_CONTROL_REG, CSR_5380_INTR);
|
||||
NCR5380_write(DTC_BLK_CNT, len >> 7); /* Block count */
|
||||
for (i = 0; len > 0; ++i) {
|
||||
rtrc(5);
|
||||
/* Poll until the host buffer can accept data. */
|
||||
while (NCR5380_read(DTC_CONTROL_REG) & CSR_HOST_BUF_NOT_RDY)
|
||||
++i;
|
||||
rtrc(3);
|
||||
memcpy_toio(hostdata->base + DTC_DATA_BUF, src, 128);
|
||||
src += 128;
|
||||
len -= 128;
|
||||
}
|
||||
rtrc(4);
|
||||
while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
|
||||
++i;
|
||||
rtrc(6);
|
||||
/* Wait until the last byte has been sent to the disk */
|
||||
while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT))
|
||||
++i;
|
||||
rtrc(7);
|
||||
/* Check for parity error here. fixme. */
|
||||
rtrc(0);
|
||||
return (0);
|
||||
}
|
||||
|
||||
static int dtc_dma_xfer_len(struct scsi_cmnd *cmd)
|
||||
{
|
||||
int transfersize = cmd->transfersize;
|
||||
|
||||
/* Limit transfers to 32K, for xx400 & xx406
|
||||
* pseudoDMA that transfers in 128 bytes blocks.
|
||||
*/
|
||||
if (transfersize > 32 * 1024 && cmd->SCp.this_residual &&
|
||||
!(cmd->SCp.this_residual % transfersize))
|
||||
transfersize = 32 * 1024;
|
||||
|
||||
return transfersize;
|
||||
}
|
||||
|
||||
MODULE_LICENSE("GPL");
|
||||
|
||||
#include "NCR5380.c"
|
||||
|
||||
static int dtc_release(struct Scsi_Host *shost)
|
||||
{
|
||||
struct NCR5380_hostdata *hostdata = shost_priv(shost);
|
||||
|
||||
if (shost->irq != NO_IRQ)
|
||||
free_irq(shost->irq, shost);
|
||||
NCR5380_exit(shost);
|
||||
scsi_unregister(shost);
|
||||
iounmap(hostdata->base);
|
||||
return 0;
|
||||
}
|
||||
|
||||
static struct scsi_host_template driver_template = {
|
||||
.name = "DTC 3180/3280",
|
||||
.detect = dtc_detect,
|
||||
.release = dtc_release,
|
||||
.proc_name = "dtc3x80",
|
||||
.info = dtc_info,
|
||||
.queuecommand = dtc_queue_command,
|
||||
.eh_abort_handler = dtc_abort,
|
||||
.eh_bus_reset_handler = dtc_bus_reset,
|
||||
.bios_param = dtc_biosparam,
|
||||
.can_queue = 32,
|
||||
.this_id = 7,
|
||||
.sg_tablesize = SG_ALL,
|
||||
.cmd_per_lun = 2,
|
||||
.use_clustering = DISABLE_CLUSTERING,
|
||||
.cmd_size = NCR5380_CMD_SIZE,
|
||||
.max_sectors = 128,
|
||||
};
|
||||
#include "scsi_module.c"
|
||||
|
|
@ -1,42 +0,0 @@
|
|||
/*
|
||||
* DTC controller, taken from T128 driver by...
|
||||
* Copyright 1993, Drew Eckhardt
|
||||
* Visionary Computing
|
||||
* (Unix and Linux consulting and custom programming)
|
||||
* drew@colorado.edu
|
||||
* +1 (303) 440-4894
|
||||
*/
|
||||
|
||||
#ifndef DTC3280_H
|
||||
#define DTC3280_H
|
||||
|
||||
#define NCR5380_implementation_fields \
|
||||
void __iomem *base
|
||||
|
||||
#define DTC_address(reg) \
|
||||
(((struct NCR5380_hostdata *)shost_priv(instance))->base + DTC_5380_OFFSET + reg)
|
||||
|
||||
#define NCR5380_read(reg) (readb(DTC_address(reg)))
|
||||
#define NCR5380_write(reg, value) (writeb(value, DTC_address(reg)))
|
||||
|
||||
#define NCR5380_dma_xfer_len(instance, cmd, phase) \
|
||||
dtc_dma_xfer_len(cmd)
|
||||
#define NCR5380_dma_recv_setup dtc_pread
|
||||
#define NCR5380_dma_send_setup dtc_pwrite
|
||||
#define NCR5380_dma_residual(instance) (0)
|
||||
|
||||
#define NCR5380_intr dtc_intr
|
||||
#define NCR5380_queue_command dtc_queue_command
|
||||
#define NCR5380_abort dtc_abort
|
||||
#define NCR5380_bus_reset dtc_bus_reset
|
||||
#define NCR5380_info dtc_info
|
||||
|
||||
#define NCR5380_io_delay(x) udelay(x)
|
||||
|
||||
/* 15 12 11 10
|
||||
1001 1100 0000 0000 */
|
||||
|
||||
#define DTC_IRQS 0x9c00
|
||||
|
||||
|
||||
#endif /* DTC3280_H */
|
||||
Загрузка…
Ссылка в новой задаче