arm64: dts: rockchip: add rk3328-rock64 board
The ROCK64 is a credit card size 4K60P HDR Media Board Computer using the Rockchip RK3328 Quad-Core ARM Cortex A53 64-Bit Processor and supporting up to 4GB 1600MHz LPDDR3 memory. It provides eMMC module socket, MicroSD Card slot, Pi-2 Bus, Pi-P5+ Bus, USB 3.0 and many others peripheral devices interface for makers to integrate with sensors and devices. The devicetree currently supports basic peripherals, with more to be added later on. Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This commit is contained in:
Heiko Stuebner
Родитель
13ed1501cb
Коммит
955bebde05
|
|
@ -134,6 +134,10 @@ Rockchip platforms device tree bindings
|
|||
Required root node properties:
|
||||
- compatible = "phytec,rk3288-pcm-947", "phytec,rk3288-phycore-som", "rockchip,rk3288";
|
||||
|
||||
- Pine64 Rock64 board:
|
||||
Required root node properties:
|
||||
- compatible = "pine64,rock64", "rockchip,rk3328";
|
||||
|
||||
- Rockchip PX3 Evaluation board:
|
||||
Required root node properties:
|
||||
- compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188";
|
||||
|
|
|
|||
|
|
@ -1,4 +1,5 @@
|
|||
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
|
||||
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
|
||||
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
|
||||
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
|
||||
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
|
||||
|
|
|
|||
|
|
@ -0,0 +1,333 @@
|
|||
/*
|
||||
* Copyright (c) 2017 PINE64
|
||||
*
|
||||
* This file is dual-licensed: you can use it either under the terms
|
||||
* of the GPL or the X11 license, at your option. Note that this dual
|
||||
* licensing only applies to this file, and not this project as a
|
||||
* whole.
|
||||
*
|
||||
* a) This library is free software; you can redistribute it and/or
|
||||
* modify it under the terms of the GNU General Public License as
|
||||
* published by the Free Software Foundation; either version 2 of the
|
||||
* License, or (at your option) any later version.
|
||||
*
|
||||
* This library is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* Or, alternatively,
|
||||
*
|
||||
* b) Permission is hereby granted, free of charge, to any person
|
||||
* obtaining a copy of this software and associated documentation
|
||||
* files (the "Software"), to deal in the Software without
|
||||
* restriction, including without limitation the rights to use,
|
||||
* copy, modify, merge, publish, distribute, sublicense, and/or
|
||||
* sell copies of the Software, and to permit persons to whom the
|
||||
* Software is furnished to do so, subject to the following
|
||||
* conditions:
|
||||
*
|
||||
* The above copyright notice and this permission notice shall be
|
||||
* included in all copies or substantial portions of the Software.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
|
||||
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
|
||||
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
|
||||
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
|
||||
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
|
||||
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
|
||||
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
|
||||
* OTHER DEALINGS IN THE SOFTWARE.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
#include "rk3328.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Pine64 Rock64";
|
||||
compatible = "pine64,rock64", "rockchip,rk3328";
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial2:1500000n8";
|
||||
};
|
||||
|
||||
gmac_clkin: external-gmac-clock {
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <125000000>;
|
||||
clock-output-names = "gmac_clkin";
|
||||
#clock-cells = <0>;
|
||||
};
|
||||
|
||||
vcc_sd: sdmmc-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc0m1_gpio>;
|
||||
regulator-name = "vcc_sd";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
vin-supply = <&vcc_io>;
|
||||
};
|
||||
|
||||
vcc_host_5v: vcc-host-5v-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&usb30_host_drv>;
|
||||
regulator-name = "vcc_host_5v";
|
||||
regulator-always-on;
|
||||
vin-supply = <&vcc_sys>;
|
||||
};
|
||||
|
||||
vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&usb20_host_drv>;
|
||||
regulator-name = "vcc_host1_5v";
|
||||
regulator-always-on;
|
||||
vin-supply = <&vcc_sys>;
|
||||
};
|
||||
|
||||
vcc_sys: vcc-sys {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc_sys";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&cpu0 {
|
||||
cpu-supply = <&vdd_arm>;
|
||||
};
|
||||
|
||||
&cpu1 {
|
||||
cpu-supply = <&vdd_arm>;
|
||||
};
|
||||
|
||||
&cpu2 {
|
||||
cpu-supply = <&vdd_arm>;
|
||||
};
|
||||
|
||||
&cpu3 {
|
||||
cpu-supply = <&vdd_arm>;
|
||||
};
|
||||
|
||||
&emmc {
|
||||
bus-width = <8>;
|
||||
cap-mmc-highspeed;
|
||||
non-removable;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
|
||||
vmmc-supply = <&vcc_io>;
|
||||
vqmmc-supply = <&vcc18_emmc>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac2io {
|
||||
assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
|
||||
assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
|
||||
clock_in_out = "input";
|
||||
phy-supply = <&vcc_io>;
|
||||
phy-mode = "rgmii";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rgmiim1_pins>;
|
||||
snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
|
||||
snps,reset-active-low;
|
||||
snps,reset-delays-us = <0 10000 50000>;
|
||||
tx_delay = <0x26>;
|
||||
rx_delay = <0x11>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
status = "okay";
|
||||
|
||||
rk805: rk805@18 {
|
||||
compatible = "rockchip,rk805";
|
||||
reg = <0x18>;
|
||||
interrupt-parent = <&gpio2>;
|
||||
interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
|
||||
#clock-cells = <1>;
|
||||
clock-output-names = "xin32k", "rk805-clkout2";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int_l>;
|
||||
rockchip,system-power-controller;
|
||||
wakeup-source;
|
||||
|
||||
vcc1-supply = <&vcc_sys>;
|
||||
vcc2-supply = <&vcc_sys>;
|
||||
vcc3-supply = <&vcc_sys>;
|
||||
vcc4-supply = <&vcc_sys>;
|
||||
vcc5-supply = <&vcc_io>;
|
||||
vcc6-supply = <&vcc_sys>;
|
||||
|
||||
regulators {
|
||||
vdd_logic: DCDC_REG1 {
|
||||
regulator-name = "vdd_logic";
|
||||
regulator-min-microvolt = <712500>;
|
||||
regulator-max-microvolt = <1450000>;
|
||||
regulator-ramp-delay = <12500>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <1000000>;
|
||||
};
|
||||
};
|
||||
|
||||
vdd_arm: DCDC_REG2 {
|
||||
regulator-name = "vdd_arm";
|
||||
regulator-min-microvolt = <712500>;
|
||||
regulator-max-microvolt = <1450000>;
|
||||
regulator-ramp-delay = <12500>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <950000>;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_ddr: DCDC_REG3 {
|
||||
regulator-name = "vcc_ddr";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_io: DCDC_REG4 {
|
||||
regulator-name = "vcc_io";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <3300000>;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_18: LDO_REG1 {
|
||||
regulator-name = "vdd_18";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <1800000>;
|
||||
};
|
||||
};
|
||||
|
||||
vcc18_emmc: LDO_REG2 {
|
||||
regulator-name = "vcc_18emmc";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <1800000>;
|
||||
};
|
||||
};
|
||||
|
||||
vdd_10: LDO_REG3 {
|
||||
regulator-name = "vdd_10";
|
||||
regulator-min-microvolt = <1000000>;
|
||||
regulator-max-microvolt = <1000000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <1000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&io_domains {
|
||||
status = "okay";
|
||||
|
||||
vccio1-supply = <&vcc_io>;
|
||||
vccio2-supply = <&vcc18_emmc>;
|
||||
vccio3-supply = <&vcc_io>;
|
||||
vccio4-supply = <&vcc_18>;
|
||||
vccio5-supply = <&vcc_io>;
|
||||
vccio6-supply = <&vcc_io>;
|
||||
pmuio-supply = <&vcc_io>;
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
pmic {
|
||||
pmic_int_l: pmic-int-l {
|
||||
rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
|
||||
};
|
||||
};
|
||||
|
||||
usb2 {
|
||||
usb20_host_drv: usb20-host-drv {
|
||||
rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
|
||||
usb3 {
|
||||
usb30_host_drv: usb30-host-drv {
|
||||
rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&sdmmc {
|
||||
bus-width = <4>;
|
||||
cap-mmc-highspeed;
|
||||
cap-sd-highspeed;
|
||||
disable-wp;
|
||||
max-frequency = <150000000>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
|
||||
vmmc-supply = <&vcc_sd>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tsadc {
|
||||
rockchip,hw-tshut-mode = <0>;
|
||||
rockchip,hw-tshut-polarity = <0>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&u2phy {
|
||||
status = "okay";
|
||||
|
||||
u2phy_host: host-port {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
u2phy_otg: otg-port {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&usb20_otg {
|
||||
dr_mode = "host";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_host0_ehci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_host0_ohci {
|
||||
status = "okay";
|
||||
};
|
||||
Загрузка…
Ссылка в новой задаче