{cfg,nl,mac}80211: set beacon interval and DTIM period on mesh join

Move the default mesh beacon interval and DTIM period to cfg80211
and make them accessible to nl80211. This enables setting both
values when joining an MBSS.

Previously the DTIM parameter was not set by mac80211 so the
driver's default value was used.

Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit is contained in:
Marco Porsch 2013-01-07 16:04:51 +01:00 коммит произвёл Johannes Berg
Родитель eac70c135d
Коммит 9bdbf04db0
6 изменённых файлов: 27 добавлений и 3 удалений

Просмотреть файл

@ -1036,6 +1036,8 @@ struct mesh_config {
* @ie_len: length of vendor information elements
* @is_authenticated: this mesh requires authentication
* @is_secure: this mesh uses security
* @dtim_period: DTIM period to use
* @beacon_interval: beacon interval to use
* @mcast_rate: multicat rate for Mesh Node [6Mbps is the default for 802.11a]
*
* These parameters are fixed when the mesh is created.
@ -1051,6 +1053,8 @@ struct mesh_setup {
u8 ie_len;
bool is_authenticated;
bool is_secure;
u8 dtim_period;
u16 beacon_interval;
int mcast_rate[IEEE80211_NUM_BANDS];
};

Просмотреть файл

@ -1666,6 +1666,9 @@ static int copy_mesh_setup(struct ieee80211_if_mesh *ifmsh,
memcpy(sdata->vif.bss_conf.mcast_rate, setup->mcast_rate,
sizeof(setup->mcast_rate));
sdata->vif.bss_conf.beacon_int = setup->beacon_interval;
sdata->vif.bss_conf.dtim_period = setup->dtim_period;
return 0;
}

Просмотреть файл

@ -625,7 +625,6 @@ void ieee80211_start_mesh(struct ieee80211_sub_if_data *sdata)
ieee80211_queue_work(&local->hw, &sdata->work);
sdata->vif.bss_conf.ht_operation_mode =
ifmsh->mshcfg.ht_opmode;
sdata->vif.bss_conf.beacon_int = MESH_DEFAULT_BEACON_INTERVAL;
sdata->vif.bss_conf.enable_beacon = true;
sdata->vif.bss_conf.basic_rates =
ieee80211_mandatory_rates(local, band);

Просмотреть файл

@ -191,8 +191,6 @@ struct mesh_rmc {
#define IEEE80211_MESH_PEER_INACTIVITY_LIMIT (1800 * HZ)
#define IEEE80211_MESH_HOUSEKEEPING_INTERVAL (60 * HZ)
#define MESH_DEFAULT_BEACON_INTERVAL 1000 /* in 1024 us units */
#define MESH_PATH_EXPIRE (600 * HZ)
/* Default maximum number of plinks per interface */

Просмотреть файл

@ -44,6 +44,9 @@
#define MESH_SYNC_NEIGHBOR_OFFSET_MAX 50
#define MESH_DEFAULT_BEACON_INTERVAL 1000 /* in 1024 us units (=TUs) */
#define MESH_DEFAULT_DTIM_PERIOD 2
const struct mesh_config default_mesh_config = {
.dot11MeshRetryTimeout = MESH_RET_T,
.dot11MeshConfirmTimeout = MESH_CONF_T,
@ -79,6 +82,8 @@ const struct mesh_setup default_mesh_setup = {
.ie = NULL,
.ie_len = 0,
.is_secure = false,
.beacon_interval = MESH_DEFAULT_BEACON_INTERVAL,
.dtim_period = MESH_DEFAULT_DTIM_PERIOD,
};
int __cfg80211_join_mesh(struct cfg80211_registered_device *rdev,

Просмотреть файл

@ -6669,6 +6669,21 @@ static int nl80211_join_mesh(struct sk_buff *skb, struct genl_info *info)
nla_get_u32(info->attrs[NL80211_ATTR_MCAST_RATE])))
return -EINVAL;
if (info->attrs[NL80211_ATTR_BEACON_INTERVAL]) {
setup.beacon_interval =
nla_get_u32(info->attrs[NL80211_ATTR_BEACON_INTERVAL]);
if (setup.beacon_interval < 10 ||
setup.beacon_interval > 10000)
return -EINVAL;
}
if (info->attrs[NL80211_ATTR_DTIM_PERIOD]) {
setup.dtim_period =
nla_get_u32(info->attrs[NL80211_ATTR_DTIM_PERIOD]);
if (setup.dtim_period < 1 || setup.dtim_period > 100)
return -EINVAL;
}
if (info->attrs[NL80211_ATTR_MESH_SETUP]) {
/* parse additional setup parameters if given */
err = nl80211_parse_mesh_setup(info, &setup);