usb: usb: dsps: update device tree bindings
The support for both am335x-USB instances required changes to the device tree bindings. This patch reflects these changes in the bindings document. v3…v4: - remove the child node for USB. This is driver specific on won't be reflected in the device tree - use the "mentor" prefix instead of "mg". - use "dr_mode" istead of "mg,port-mode" for the port mode. The former is used by a few other drivers. v2…v3: - use proper usb-phy nodes in evm, bone and evmsk device tree. v1…v2: - use mg prefix for the Metor Graphics specific attributes - use power in mA not in mA/2 as specifed in the USB2.0 specification - use usbX-phy instead of usbX_phy - use dma-controller instead of dma Cc: Rob Herring <rob.herring@calxeda.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: devicetree@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit is contained in:
Sebastian Andrzej Siewior
Felipe Balbi
Родитель
3b6394b4fa
Коммит
a0b311ef17
|
|
@ -1,35 +1,197 @@
|
|||
AM33XX MUSB GLUE
|
||||
- compatible : Should be "ti,musb-am33xx"
|
||||
- reg : offset and length of register sets, first usbss, then for musb instances
|
||||
- interrupts : usbss, musb instance interrupts in order
|
||||
- ti,hwmods : must be "usb_otg_hs"
|
||||
- multipoint : Should be "1" indicating the musb controller supports
|
||||
multipoint. This is a MUSB configuration-specific setting.
|
||||
- num-eps : Specifies the number of endpoints. This is also a
|
||||
MUSB configuration-specific setting. Should be set to "16"
|
||||
- ram-bits : Specifies the ram address size. Should be set to "12"
|
||||
- port0-mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
|
||||
represents PERIPHERAL.
|
||||
- port1-mode : Should be "1" to represent HOST. "3" signifies OTG and "2"
|
||||
represents PERIPHERAL.
|
||||
- power : Should be "250". This signifies the controller can supply up to
|
||||
500mA when operating in host mode.
|
||||
AM33xx MUSB
|
||||
~~~~~~~~~~~~~~~
|
||||
- compatible: ti,am33xx-usb
|
||||
- reg: offset and length of the usbss register sets
|
||||
- ti,hwmods : must be "usb_otg_hs"
|
||||
|
||||
The glue layer contains multiple child nodes. It is required the have
|
||||
at least a control module node, USB node and a PHY node. The second USB
|
||||
node and its PHY node is optional. The DMA node is also optional.
|
||||
|
||||
Reset module
|
||||
~~~~~~~~~~~~
|
||||
- compatible: ti,am335x-usb-ctrl-module
|
||||
- reg: offset and length of the "USB control registers" in the "Control
|
||||
Module" block. A second offset and length for the USB wake up control
|
||||
in the same memory block.
|
||||
- reg-names: "phy_ctrl" for the "USB control registers" and "wakeup" for
|
||||
the USB wake up control register.
|
||||
|
||||
USB PHY
|
||||
~~~~~~~
|
||||
compatible: ti,am335x-usb-phy
|
||||
reg: offset and length of the "USB PHY" register space
|
||||
ti,ctrl_mod: reference to the "reset module" node
|
||||
reg-names: phy
|
||||
The PHY should have a "phy" alias numbered properly in the alias
|
||||
node.
|
||||
|
||||
USB
|
||||
~~~
|
||||
- compatible: ti,musb-am33xx
|
||||
- reg: offset and length of "USB Controller Registers", and offset and
|
||||
length of "USB Core" register space.
|
||||
- reg-names: control for the ""USB Controller Registers" and "mc" for
|
||||
"USB Core" register space
|
||||
- interrupts: USB interrupt number
|
||||
- interrupt-names: mc
|
||||
- dr_mode: Should be one of "host", "peripheral" or "otg".
|
||||
- mentor,multipoint: Should be "1" indicating the musb controller supports
|
||||
multipoint. This is a MUSB configuration-specific setting.
|
||||
- mentor,num-eps: Specifies the number of endpoints. This is also a
|
||||
MUSB configuration-specific setting. Should be set to "16"
|
||||
- mentor,ram-bits: Specifies the ram address size. Should be set to "12"
|
||||
- mentor,power: Should be "500". This signifies the controller can supply up to
|
||||
500mA when operating in host mode.
|
||||
- phys: reference to the USB phy
|
||||
- dmas: specifies the dma channels
|
||||
- dma-names: specifies the names of the channels. Use "rxN" for receive
|
||||
and "txN" for transmit endpoints. N specifies the endpoint number.
|
||||
|
||||
The controller should have an "usb" alias numbered properly in the alias
|
||||
node.
|
||||
|
||||
DMA
|
||||
~~~
|
||||
- compatible: ti,am3359-cppi41
|
||||
- reg: offset and length of the following register spaces: USBSS, USB
|
||||
CPPI DMA Controller, USB CPPI DMA Scheduler, USB Queue Manager
|
||||
- reg-names: glue, controller, scheduler, queuemgr
|
||||
- #dma-cells: should be set to 2. The first number represents the
|
||||
endpoint number (0 … 14 for endpoints 1 … 15 on instance 0 and 15 … 29
|
||||
for endpoints 1 … 15 on instance 1). The second number is 0 for RX and
|
||||
1 for TX transfers.
|
||||
- #dma-channels: should be set to 30 representing the 15 endpoints for
|
||||
each USB instance.
|
||||
|
||||
Example:
|
||||
~~~~~~~~
|
||||
The following example contains all the nodes as used on am335x-evm:
|
||||
|
||||
usb@47400000 {
|
||||
compatible = "ti,musb-am33xx";
|
||||
reg = <0x47400000 0x1000 /* usbss */
|
||||
0x47401000 0x800 /* musb instance 0 */
|
||||
0x47401800 0x800>; /* musb instance 1 */
|
||||
interrupts = <17 /* usbss */
|
||||
18 /* musb instance 0 */
|
||||
19>; /* musb instance 1 */
|
||||
multipoint = <1>;
|
||||
num-eps = <16>;
|
||||
ram-bits = <12>;
|
||||
port0-mode = <3>;
|
||||
port1-mode = <3>;
|
||||
power = <250>;
|
||||
ti,hwmods = "usb_otg_hs";
|
||||
aliases {
|
||||
usb0 = &usb0;
|
||||
usb1 = &usb1;
|
||||
phy0 = &usb0_phy;
|
||||
phy1 = &usb1_phy;
|
||||
};
|
||||
|
||||
usb: usb@47400000 {
|
||||
compatible = "ti,am33xx-usb";
|
||||
reg = <0x47400000 0x1000>;
|
||||
ranges;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ti,hwmods = "usb_otg_hs";
|
||||
|
||||
ctrl_mod: control@44e10000 {
|
||||
compatible = "ti,am335x-usb-ctrl-module";
|
||||
reg = <0x44e10620 0x10
|
||||
0x44e10648 0x4>;
|
||||
reg-names = "phy_ctrl", "wakeup";
|
||||
};
|
||||
|
||||
usb0_phy: usb-phy@47401300 {
|
||||
compatible = "ti,am335x-usb-phy";
|
||||
reg = <0x47401300 0x100>;
|
||||
reg-names = "phy";
|
||||
ti,ctrl_mod = <&ctrl_mod>;
|
||||
};
|
||||
|
||||
usb0: usb@47401000 {
|
||||
compatible = "ti,musb-am33xx";
|
||||
reg = <0x47401400 0x400
|
||||
0x47401000 0x200>;
|
||||
reg-names = "mc", "control";
|
||||
|
||||
interrupts = <18>;
|
||||
interrupt-names = "mc";
|
||||
dr_mode = "otg"
|
||||
mentor,multipoint = <1>;
|
||||
mentor,num-eps = <16>;
|
||||
mentor,ram-bits = <12>;
|
||||
mentor,power = <500>;
|
||||
phys = <&usb0_phy>;
|
||||
|
||||
dmas = <&cppi41dma 0 0 &cppi41dma 1 0
|
||||
&cppi41dma 2 0 &cppi41dma 3 0
|
||||
&cppi41dma 4 0 &cppi41dma 5 0
|
||||
&cppi41dma 6 0 &cppi41dma 7 0
|
||||
&cppi41dma 8 0 &cppi41dma 9 0
|
||||
&cppi41dma 10 0 &cppi41dma 11 0
|
||||
&cppi41dma 12 0 &cppi41dma 13 0
|
||||
&cppi41dma 14 0 &cppi41dma 0 1
|
||||
&cppi41dma 1 1 &cppi41dma 2 1
|
||||
&cppi41dma 3 1 &cppi41dma 4 1
|
||||
&cppi41dma 5 1 &cppi41dma 6 1
|
||||
&cppi41dma 7 1 &cppi41dma 8 1
|
||||
&cppi41dma 9 1 &cppi41dma 10 1
|
||||
&cppi41dma 11 1 &cppi41dma 12 1
|
||||
&cppi41dma 13 1 &cppi41dma 14 1>;
|
||||
dma-names =
|
||||
"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
|
||||
"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
|
||||
"rx14", "rx15",
|
||||
"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
|
||||
"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
|
||||
"tx14", "tx15";
|
||||
};
|
||||
|
||||
usb1_phy: usb-phy@47401b00 {
|
||||
compatible = "ti,am335x-usb-phy";
|
||||
reg = <0x47401b00 0x100>;
|
||||
reg-names = "phy";
|
||||
ti,ctrl_mod = <&ctrl_mod>;
|
||||
};
|
||||
|
||||
usb1: usb@47401800 {
|
||||
compatible = "ti,musb-am33xx";
|
||||
reg = <0x47401c00 0x400
|
||||
0x47401800 0x200>;
|
||||
reg-names = "mc", "control";
|
||||
interrupts = <19>;
|
||||
interrupt-names = "mc";
|
||||
dr_mode = "host"
|
||||
mentor,multipoint = <1>;
|
||||
mentor,num-eps = <16>;
|
||||
mentor,ram-bits = <12>;
|
||||
mentor,power = <500>;
|
||||
phys = <&usb1_phy>;
|
||||
|
||||
dmas = <&cppi41dma 15 0 &cppi41dma 16 0
|
||||
&cppi41dma 17 0 &cppi41dma 18 0
|
||||
&cppi41dma 19 0 &cppi41dma 20 0
|
||||
&cppi41dma 21 0 &cppi41dma 22 0
|
||||
&cppi41dma 23 0 &cppi41dma 24 0
|
||||
&cppi41dma 25 0 &cppi41dma 26 0
|
||||
&cppi41dma 27 0 &cppi41dma 28 0
|
||||
&cppi41dma 29 0 &cppi41dma 15 1
|
||||
&cppi41dma 16 1 &cppi41dma 17 1
|
||||
&cppi41dma 18 1 &cppi41dma 19 1
|
||||
&cppi41dma 20 1 &cppi41dma 21 1
|
||||
&cppi41dma 22 1 &cppi41dma 23 1
|
||||
&cppi41dma 24 1 &cppi41dma 25 1
|
||||
&cppi41dma 26 1 &cppi41dma 27 1
|
||||
&cppi41dma 28 1 &cppi41dma 29 1>;
|
||||
dma-names =
|
||||
"rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
|
||||
"rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
|
||||
"rx14", "rx15",
|
||||
"tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
|
||||
"tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
|
||||
"tx14", "tx15";
|
||||
};
|
||||
|
||||
cppi41dma: dma-controller@07402000 {
|
||||
compatible = "ti,am3359-cppi41";
|
||||
reg = <0x47400000 0x1000
|
||||
0x47402000 0x1000
|
||||
0x47403000 0x1000
|
||||
0x47404000 0x4000>;
|
||||
reg-names = "glue", "controller", "scheduler", "queuemgr";
|
||||
interrupts = <17>;
|
||||
interrupt-names = "glue";
|
||||
#dma-cells = <2>;
|
||||
#dma-channels = <30>;
|
||||
#dma-requests = <256>;
|
||||
};
|
||||
};
|
||||
|
|
|
|||
Загрузка…
Ссылка в новой задаче