w1: add 1-wire master driver for i.MX27 / i.MX31
This patch adds support for the 1-wire master interface for i.MX27 and i.MX31. Signed-off-by: Luotao Fu <l.fu@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit is contained in:
Родитель
09f50c9542
Коммит
a5fd9139f7
|
@ -4,5 +4,7 @@ ds2482
|
|||
- The Maxim/Dallas Semiconductor DS2482 provides 1-wire busses.
|
||||
ds2490
|
||||
- The Maxim/Dallas Semiconductor DS2490 builds USB <-> W1 bridges.
|
||||
mxc_w1
|
||||
- W1 master controller driver found on Freescale MX2/MX3 SoCs
|
||||
w1-gpio
|
||||
- GPIO 1-wire bus master driver.
|
||||
|
|
|
@ -0,0 +1,11 @@
|
|||
Kernel driver mxc_w1
|
||||
====================
|
||||
|
||||
Supported chips:
|
||||
* Freescale MX27, MX31 and probably other i.MX SoCs
|
||||
Datasheets:
|
||||
http://www.freescale.com/files/32bit/doc/data_sheet/MCIMX31.pdf?fpsp=1
|
||||
http://www.freescale.com/files/dsp/MCIMX27.pdf?fpsp=1
|
||||
|
||||
Author: Originally based on Freescale code, prepared for mainline by
|
||||
Sascha Hauer <s.hauer@pengutronix.de>
|
|
@ -34,6 +34,12 @@ config W1_MASTER_DS2482
|
|||
This driver can also be built as a module. If so, the module
|
||||
will be called ds2482.
|
||||
|
||||
config W1_MASTER_MXC
|
||||
tristate "Freescale MXC 1-wire busmaster"
|
||||
depends on W1 && ARCH_MXC
|
||||
help
|
||||
Say Y here to enable MXC 1-wire host
|
||||
|
||||
config W1_MASTER_DS1WM
|
||||
tristate "Maxim DS1WM 1-wire busmaster"
|
||||
depends on W1 && ARM && HAVE_CLK
|
||||
|
|
|
@ -5,6 +5,8 @@
|
|||
obj-$(CONFIG_W1_MASTER_MATROX) += matrox_w1.o
|
||||
obj-$(CONFIG_W1_MASTER_DS2490) += ds2490.o
|
||||
obj-$(CONFIG_W1_MASTER_DS2482) += ds2482.o
|
||||
obj-$(CONFIG_W1_MASTER_MXC) += mxc_w1.o
|
||||
|
||||
obj-$(CONFIG_W1_MASTER_DS1WM) += ds1wm.o
|
||||
obj-$(CONFIG_W1_MASTER_GPIO) += w1-gpio.o
|
||||
obj-$(CONFIG_HDQ_MASTER_OMAP) += omap_hdq.o
|
||||
|
|
|
@ -0,0 +1,211 @@
|
|||
/*
|
||||
* Copyright 2005-2008 Freescale Semiconductor, Inc. All Rights Reserved.
|
||||
* Copyright 2008 Luotao Fu, kernel@pengutronix.de
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or
|
||||
* modify it under the terms of the GNU General Public License
|
||||
* as published by the Free Software Foundation; either version 2
|
||||
* of the License, or (at your option) any later version.
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program; if not, write to the Free Software
|
||||
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
|
||||
*
|
||||
*/
|
||||
|
||||
#include <linux/module.h>
|
||||
#include <linux/interrupt.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/clk.h>
|
||||
#include <linux/delay.h>
|
||||
#include <linux/io.h>
|
||||
|
||||
#include "../w1.h"
|
||||
#include "../w1_int.h"
|
||||
#include "../w1_log.h"
|
||||
|
||||
/* According to the mx27 Datasheet the reset procedure should take up to about
|
||||
* 1350us. We set the timeout to 500*100us = 50ms for sure */
|
||||
#define MXC_W1_RESET_TIMEOUT 500
|
||||
|
||||
/*
|
||||
* MXC W1 Register offsets
|
||||
*/
|
||||
#define MXC_W1_CONTROL 0x00
|
||||
#define MXC_W1_TIME_DIVIDER 0x02
|
||||
#define MXC_W1_RESET 0x04
|
||||
#define MXC_W1_COMMAND 0x06
|
||||
#define MXC_W1_TXRX 0x08
|
||||
#define MXC_W1_INTERRUPT 0x0A
|
||||
#define MXC_W1_INTERRUPT_EN 0x0C
|
||||
|
||||
struct mxc_w1_device {
|
||||
void __iomem *regs;
|
||||
unsigned int clkdiv;
|
||||
struct clk *clk;
|
||||
struct w1_bus_master bus_master;
|
||||
};
|
||||
|
||||
/*
|
||||
* this is the low level routine to
|
||||
* reset the device on the One Wire interface
|
||||
* on the hardware
|
||||
*/
|
||||
static u8 mxc_w1_ds2_reset_bus(void *data)
|
||||
{
|
||||
u8 reg_val;
|
||||
unsigned int timeout_cnt = 0;
|
||||
struct mxc_w1_device *dev = data;
|
||||
|
||||
__raw_writeb(0x80, (dev->regs + MXC_W1_CONTROL));
|
||||
|
||||
while (1) {
|
||||
reg_val = __raw_readb(dev->regs + MXC_W1_CONTROL);
|
||||
|
||||
if (((reg_val >> 7) & 0x1) == 0 ||
|
||||
timeout_cnt > MXC_W1_RESET_TIMEOUT)
|
||||
break;
|
||||
else
|
||||
timeout_cnt++;
|
||||
|
||||
udelay(100);
|
||||
}
|
||||
return (reg_val >> 7) & 0x1;
|
||||
}
|
||||
|
||||
/*
|
||||
* this is the low level routine to read/write a bit on the One Wire
|
||||
* interface on the hardware. It does write 0 if parameter bit is set
|
||||
* to 0, otherwise a write 1/read.
|
||||
*/
|
||||
static u8 mxc_w1_ds2_touch_bit(void *data, u8 bit)
|
||||
{
|
||||
struct mxc_w1_device *mdev = data;
|
||||
void __iomem *ctrl_addr = mdev->regs + MXC_W1_CONTROL;
|
||||
unsigned int timeout_cnt = 400; /* Takes max. 120us according to
|
||||
* datasheet.
|
||||
*/
|
||||
|
||||
__raw_writeb((1 << (5 - bit)), ctrl_addr);
|
||||
|
||||
while (timeout_cnt--) {
|
||||
if (!((__raw_readb(ctrl_addr) >> (5 - bit)) & 0x1))
|
||||
break;
|
||||
|
||||
udelay(1);
|
||||
}
|
||||
|
||||
return ((__raw_readb(ctrl_addr)) >> 3) & 0x1;
|
||||
}
|
||||
|
||||
static int __init mxc_w1_probe(struct platform_device *pdev)
|
||||
{
|
||||
struct mxc_w1_device *mdev;
|
||||
struct resource *res;
|
||||
int err = 0;
|
||||
|
||||
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
||||
if (!res)
|
||||
return -ENODEV;
|
||||
|
||||
mdev = kzalloc(sizeof(struct mxc_w1_device), GFP_KERNEL);
|
||||
if (!mdev)
|
||||
return -ENOMEM;
|
||||
|
||||
mdev->clk = clk_get(&pdev->dev, "owire_clk");
|
||||
if (!mdev->clk) {
|
||||
err = -ENODEV;
|
||||
goto failed_clk;
|
||||
}
|
||||
|
||||
mdev->clkdiv = (clk_get_rate(mdev->clk) / 1000000) - 1;
|
||||
|
||||
res = request_mem_region(res->start, resource_size(res),
|
||||
"mxc_w1");
|
||||
if (!res) {
|
||||
err = -EBUSY;
|
||||
goto failed_req;
|
||||
}
|
||||
|
||||
mdev->regs = ioremap(res->start, resource_size(res));
|
||||
if (!mdev->regs) {
|
||||
printk(KERN_ERR "Cannot map frame buffer registers\n");
|
||||
goto failed_ioremap;
|
||||
}
|
||||
|
||||
clk_enable(mdev->clk);
|
||||
__raw_writeb(mdev->clkdiv, mdev->regs + MXC_W1_TIME_DIVIDER);
|
||||
|
||||
mdev->bus_master.data = mdev;
|
||||
mdev->bus_master.reset_bus = mxc_w1_ds2_reset_bus;
|
||||
mdev->bus_master.touch_bit = mxc_w1_ds2_touch_bit;
|
||||
|
||||
err = w1_add_master_device(&mdev->bus_master);
|
||||
|
||||
if (err)
|
||||
goto failed_add;
|
||||
|
||||
platform_set_drvdata(pdev, mdev);
|
||||
return 0;
|
||||
|
||||
failed_add:
|
||||
iounmap(mdev->regs);
|
||||
failed_ioremap:
|
||||
release_mem_region(res->start, resource_size(res));
|
||||
failed_req:
|
||||
clk_put(mdev->clk);
|
||||
failed_clk:
|
||||
kfree(mdev);
|
||||
return err;
|
||||
}
|
||||
|
||||
/*
|
||||
* disassociate the w1 device from the driver
|
||||
*/
|
||||
static int mxc_w1_remove(struct platform_device *pdev)
|
||||
{
|
||||
struct mxc_w1_device *mdev = platform_get_drvdata(pdev);
|
||||
struct resource *res;
|
||||
|
||||
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
||||
|
||||
w1_remove_master_device(&mdev->bus_master);
|
||||
|
||||
iounmap(mdev->regs);
|
||||
release_mem_region(res->start, resource_size(res));
|
||||
clk_disable(mdev->clk);
|
||||
clk_put(mdev->clk);
|
||||
|
||||
platform_set_drvdata(pdev, NULL);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static struct platform_driver mxc_w1_driver = {
|
||||
.driver = {
|
||||
.name = "mxc_w1",
|
||||
},
|
||||
.probe = mxc_w1_probe,
|
||||
.remove = mxc_w1_remove,
|
||||
};
|
||||
|
||||
static int __init mxc_w1_init(void)
|
||||
{
|
||||
return platform_driver_register(&mxc_w1_driver);
|
||||
}
|
||||
|
||||
static void mxc_w1_exit(void)
|
||||
{
|
||||
platform_driver_unregister(&mxc_w1_driver);
|
||||
}
|
||||
|
||||
module_init(mxc_w1_init);
|
||||
module_exit(mxc_w1_exit);
|
||||
|
||||
MODULE_LICENSE("GPL");
|
||||
MODULE_AUTHOR("Freescale Semiconductors Inc");
|
||||
MODULE_DESCRIPTION("Driver for One-Wire on MXC");
|
Загрузка…
Ссылка в новой задаче