diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt new file mode 100644 index 000000000000..9f7a85bb8fca --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt @@ -0,0 +1,130 @@ +ImgTec TZ1090 PDC pin controller + +Required properties: +- compatible: "img,tz1090-pdc-pinctrl" +- reg: Should contain the register physical address and length of the + SOC_GPIO_CONTROL registers in the PDC register region. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +TZ1090-PDC's pin configuration nodes act as a container for an abitrary number +of subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. For this reason, even seemingly boolean +values are actually tristates in this binding: unspecified, off, or on. +Unspecified is represented as an absent property, and off/on are represented as +integer values 0 and 1. + +Required subnode-properties: +- tz1090,pins : An array of strings. Each string contains the name of a pin or + group. Valid values for these names are listed below. + +Optional subnode-properties: +- tz1090,function: A string containing the name of the function to mux to the + pin or group. Valid values for function names are listed below, including + which pingroups can be muxed to them. +- supported generic pinconfig properties (for further details see + Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt): + - bias-disable + - bias-high-impedance + - bias-bus-hold + - bias-pull-up + - bias-pull-down + - input-schmitt-enable + - input-schmitt-disable + - slew-rate: Integer, control slew rate of pins. + 0: slow (half frequency) + 1: fast + - drive-strength: Integer, control drive strength of pins in mA. + 2: 2mA + 4: 4mA + 8: 8mA + 12: 12mA + - low-power-enable: Flag, power-on-start weak pull-down for invalid power. + - low-power-disable: Flag, power-on-start weak pull-down disabled. + +Note that many of these properties are only valid for certain specific pins +or groups. See the TZ1090 TRM for complete details regarding which groups +support which functionality. The Linux pinctrl driver may also be a useful +reference. + +Valid values for pin and group names are: + + pins: + + These all support bias-high-impediance, bias-pull-up, bias-pull-down, and + bias-bus-hold (which can also be provided to any of the groups below to set + it for all gpio pins in that group). + + gpio0, gpio1, sys_wake0, sys_wake1, sys_wake2, ir_data, ext_power. + + mux groups: + + These all support function. + + gpio0 + pins: gpio0. + function: ir_mod_stable_out. + gpio1 + pins: gpio1. + function: ir_mod_power_out. + + drive groups: + + These support input-schmitt-enable, input-schmitt-disable, slew-rate, + drive-strength, low-power-enable, and low-power-disable. + + pdc + pins: gpio0, gpio1, sys_wake0, sys_wake1, sys_wake2, ir_data, + ext_power. + +Example: + + pinctrl_pdc: pinctrl@02006500 { + #gpio-range-cells = <3>; + compatible = "img,tz1090-pdc-pinctrl"; + reg = <0x02006500 0x100>; + }; + +Example board file extracts: + + &pinctrl_pdc { + pinctrl-names = "default"; + pinctrl-0 = <&syswake_default>; + + syswake_default: syswakes { + syswake_cfg { + tz1090,pins = "sys_wake0", + "sys_wake1", + "sys_wake2"; + pull-up; + }; + }; + irmod_default: irmod { + gpio0_cfg { + tz1090,pins = "gpio0"; + tz1090,function = "ir_mod_stable_out"; + }; + gpio1_cfg { + tz1090,pins = "gpio1"; + tz1090,function = "ir_mod_power_out"; + }; + }; + }; + + ir: ir@02006200 { + pinctrl-names = "default"; + pinctrl-0 = <&irmod_default>; + }; diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index acdaa08b325c..74ec8348eed6 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -218,6 +218,12 @@ config PINCTRL_TZ1090 select PINMUX select GENERIC_PINCONF +config PINCTRL_TZ1090_PDC + bool "Toumaz Xenif TZ1090 PDC pin control driver" + depends on SOC_TZ1090 + select PINMUX + select PINCONF + config PINCTRL_U300 bool "U300 pin controller driver" depends on ARCH_U300 diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile index 37ff29e1bba3..cf699a519e9a 100644 --- a/drivers/pinctrl/Makefile +++ b/drivers/pinctrl/Makefile @@ -41,6 +41,7 @@ obj-$(CONFIG_PINCTRL_TEGRA20) += pinctrl-tegra20.o obj-$(CONFIG_PINCTRL_TEGRA30) += pinctrl-tegra30.o obj-$(CONFIG_PINCTRL_TEGRA114) += pinctrl-tegra114.o obj-$(CONFIG_PINCTRL_TZ1090) += pinctrl-tz1090.o +obj-$(CONFIG_PINCTRL_TZ1090_PDC) += pinctrl-tz1090-pdc.o obj-$(CONFIG_PINCTRL_U300) += pinctrl-u300.o obj-$(CONFIG_PINCTRL_COH901) += pinctrl-coh901.o obj-$(CONFIG_PINCTRL_SAMSUNG) += pinctrl-samsung.o diff --git a/drivers/pinctrl/pinctrl-tz1090-pdc.c b/drivers/pinctrl/pinctrl-tz1090-pdc.c new file mode 100644 index 000000000000..12e480869468 --- /dev/null +++ b/drivers/pinctrl/pinctrl-tz1090-pdc.c @@ -0,0 +1,1029 @@ +/* + * Pinctrl driver for the Toumaz Xenif TZ1090 PowerDown Controller pins + * + * Copyright (c) 2013, Imagination Technologies Ltd. + * + * Derived from Tegra code: + * Copyright (c) 2011-2012, NVIDIA CORPORATION. All rights reserved. + * + * Derived from code: + * Copyright (C) 2010 Google, Inc. + * Copyright (C) 2010 NVIDIA Corporation + * Copyright (C) 2009-2011 ST-Ericsson AB + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* + * The registers may be shared with other threads/cores, so we need to use the + * metag global lock2 for atomicity. + */ +#include + +#include "core.h" +#include "pinconf.h" + +/* Register offsets from bank base address */ +#define REG_GPIO_CONTROL0 0x00 +#define REG_GPIO_CONTROL2 0x08 + +/* Register field information */ +#define REG_GPIO_CONTROL2_PU_PD_S 16 +#define REG_GPIO_CONTROL2_PDC_POS_S 4 +#define REG_GPIO_CONTROL2_PDC_DR_S 2 +#define REG_GPIO_CONTROL2_PDC_SR_S 1 +#define REG_GPIO_CONTROL2_PDC_SCHMITT_S 0 + +/* PU_PD field values */ +#define REG_PU_PD_TRISTATE 0 +#define REG_PU_PD_UP 1 +#define REG_PU_PD_DOWN 2 +#define REG_PU_PD_REPEATER 3 + +/* DR field values */ +#define REG_DR_2mA 0 +#define REG_DR_4mA 1 +#define REG_DR_8mA 2 +#define REG_DR_12mA 3 + +/** + * struct tz1090_pdc_function - TZ1090 PDC pinctrl mux function + * @name: The name of the function, exported to pinctrl core. + * @groups: An array of pin groups that may select this function. + * @ngroups: The number of entries in @groups. + */ +struct tz1090_pdc_function { + const char *name; + const char * const *groups; + unsigned int ngroups; +}; + +/** + * struct tz1090_pdc_pingroup - TZ1090 PDC pin group + * @name: Name of pin group. + * @pins: Array of pin numbers in this pin group. + * @npins: Number of pins in this pin group. + * @func: Function enabled by the mux. + * @reg: Mux register offset. + * @bit: Mux register bit. + * @drv: Drive control supported, otherwise it's a mux. + * This means Schmitt, Slew, and Drive strength. + * + * A representation of a group of pins (possibly just one pin) in the TZ1090 + * PDC pin controller. Each group allows some parameter or parameters to be + * configured. The most common is mux function selection. + */ +struct tz1090_pdc_pingroup { + const char *name; + const unsigned int *pins; + unsigned int npins; + int func; + u16 reg; + u8 bit; + bool drv; +}; + +/* + * All PDC pins can be GPIOs. Define these first to match how the GPIO driver + * names/numbers its pins. + */ + +enum tz1090_pdc_pin { + TZ1090_PDC_PIN_GPIO0, + TZ1090_PDC_PIN_GPIO1, + TZ1090_PDC_PIN_SYS_WAKE0, + TZ1090_PDC_PIN_SYS_WAKE1, + TZ1090_PDC_PIN_SYS_WAKE2, + TZ1090_PDC_PIN_IR_DATA, + TZ1090_PDC_PIN_EXT_POWER, +}; + +/* Pin names */ + +static const struct pinctrl_pin_desc tz1090_pdc_pins[] = { + /* PDC GPIOs */ + PINCTRL_PIN(TZ1090_PDC_PIN_GPIO0, "gpio0"), + PINCTRL_PIN(TZ1090_PDC_PIN_GPIO1, "gpio1"), + PINCTRL_PIN(TZ1090_PDC_PIN_SYS_WAKE0, "sys_wake0"), + PINCTRL_PIN(TZ1090_PDC_PIN_SYS_WAKE1, "sys_wake1"), + PINCTRL_PIN(TZ1090_PDC_PIN_SYS_WAKE2, "sys_wake2"), + PINCTRL_PIN(TZ1090_PDC_PIN_IR_DATA, "ir_data"), + PINCTRL_PIN(TZ1090_PDC_PIN_EXT_POWER, "ext_power"), +}; + +/* Pin group pins */ + +static const unsigned int gpio0_pins[] = { + TZ1090_PDC_PIN_GPIO0, +}; + +static const unsigned int gpio1_pins[] = { + TZ1090_PDC_PIN_GPIO1, +}; + +static const unsigned int pdc_pins[] = { + TZ1090_PDC_PIN_GPIO0, + TZ1090_PDC_PIN_GPIO1, + TZ1090_PDC_PIN_SYS_WAKE0, + TZ1090_PDC_PIN_SYS_WAKE1, + TZ1090_PDC_PIN_SYS_WAKE2, + TZ1090_PDC_PIN_IR_DATA, + TZ1090_PDC_PIN_EXT_POWER, +}; + +/* Mux functions */ + +enum tz1090_pdc_mux { + /* PDC_GPIO0 mux */ + TZ1090_PDC_MUX_IR_MOD_STABLE_OUT, + /* PDC_GPIO1 mux */ + TZ1090_PDC_MUX_IR_MOD_POWER_OUT, +}; + +/* Pin groups a function can be muxed to */ + +static const char * const gpio0_groups[] = { + "gpio0", +}; + +static const char * const gpio1_groups[] = { + "gpio1", +}; + +#define FUNCTION(mux, fname, group) \ + [(TZ1090_PDC_MUX_ ## mux)] = { \ + .name = #fname, \ + .groups = group##_groups, \ + .ngroups = ARRAY_SIZE(group##_groups), \ + } + +/* Must correlate with enum tz1090_pdc_mux */ +static const struct tz1090_pdc_function tz1090_pdc_functions[] = { + /* MUX fn pingroups */ + FUNCTION(IR_MOD_STABLE_OUT, ir_mod_stable_out, gpio0), + FUNCTION(IR_MOD_POWER_OUT, ir_mod_power_out, gpio1), +}; + +/** + * MUX_PG() - Initialise a pin group with mux control + * @pg_name: Pin group name (stringified, _pins appended to get pins array) + * @f0: Function 0 (TZ1090_PDC_MUX_ is prepended) + * @mux_r: Mux register (REG_PINCTRL_ is prepended) + * @mux_b: Bit number in register of mux field + */ +#define MUX_PG(pg_name, f0, mux_r, mux_b) \ + { \ + .name = #pg_name, \ + .pins = pg_name##_pins, \ + .npins = ARRAY_SIZE(pg_name##_pins), \ + .func = TZ1090_PDC_MUX_ ## f0, \ + .reg = (REG_ ## mux_r), \ + .bit = (mux_b), \ + } + +/** + * DRV_PG() - Initialise a pin group with drive control + * @pg_name: Pin group name (stringified, _pins appended to get pins array) + */ +#define DRV_PG(pg_name) \ + { \ + .name = #pg_name, \ + .pins = pg_name##_pins, \ + .npins = ARRAY_SIZE(pg_name##_pins), \ + .drv = true, \ + } + +static const struct tz1090_pdc_pingroup tz1090_pdc_groups[] = { + /* Muxing pin groups */ + /* pg_name, f0, mux register, mux bit */ + MUX_PG(gpio0, IR_MOD_STABLE_OUT, GPIO_CONTROL0, 7), + MUX_PG(gpio1, IR_MOD_POWER_OUT, GPIO_CONTROL0, 6), + + /* Drive pin groups */ + /* pg_name */ + DRV_PG(pdc), +}; + +/** + * struct tz1090_pdc_pmx - Private pinctrl data + * @dev: Platform device + * @pctl: Pin control device + * @regs: Register region + * @lock: Lock protecting coherency of mux_en and gpio_en + * @mux_en: Muxes that have been enabled + * @gpio_en: Muxable GPIOs that have been enabled + */ +struct tz1090_pdc_pmx { + struct device *dev; + struct pinctrl_dev *pctl; + void __iomem *regs; + spinlock_t lock; + u32 mux_en; + u32 gpio_en; +}; + +static inline u32 pmx_read(struct tz1090_pdc_pmx *pmx, u32 reg) +{ + return ioread32(pmx->regs + reg); +} + +static inline void pmx_write(struct tz1090_pdc_pmx *pmx, u32 val, u32 reg) +{ + iowrite32(val, pmx->regs + reg); +} + +/* + * Pin control operations + */ + +static int tz1090_pdc_pinctrl_get_groups_count(struct pinctrl_dev *pctldev) +{ + return ARRAY_SIZE(tz1090_pdc_groups); +} + +static const char *tz1090_pdc_pinctrl_get_group_name(struct pinctrl_dev *pctl, + unsigned int group) +{ + return tz1090_pdc_groups[group].name; +} + +static int tz1090_pdc_pinctrl_get_group_pins(struct pinctrl_dev *pctldev, + unsigned int group, + const unsigned int **pins, + unsigned int *num_pins) +{ + *pins = tz1090_pdc_groups[group].pins; + *num_pins = tz1090_pdc_groups[group].npins; + + return 0; +} + +#ifdef CONFIG_DEBUG_FS +static void tz1090_pdc_pinctrl_pin_dbg_show(struct pinctrl_dev *pctldev, + struct seq_file *s, + unsigned int offset) +{ + seq_printf(s, " %s", dev_name(pctldev->dev)); +} +#endif + +static int reserve_map(struct device *dev, struct pinctrl_map **map, + unsigned int *reserved_maps, unsigned int *num_maps, + unsigned int reserve) +{ + unsigned int old_num = *reserved_maps; + unsigned int new_num = *num_maps + reserve; + struct pinctrl_map *new_map; + + if (old_num >= new_num) + return 0; + + new_map = krealloc(*map, sizeof(*new_map) * new_num, GFP_KERNEL); + if (!new_map) { + dev_err(dev, "krealloc(map) failed\n"); + return -ENOMEM; + } + + memset(new_map + old_num, 0, (new_num - old_num) * sizeof(*new_map)); + + *map = new_map; + *reserved_maps = new_num; + + return 0; +} + +static int add_map_mux(struct pinctrl_map **map, unsigned int *reserved_maps, + unsigned int *num_maps, const char *group, + const char *function) +{ + if (WARN_ON(*num_maps == *reserved_maps)) + return -ENOSPC; + + (*map)[*num_maps].type = PIN_MAP_TYPE_MUX_GROUP; + (*map)[*num_maps].data.mux.group = group; + (*map)[*num_maps].data.mux.function = function; + (*num_maps)++; + + return 0; +} + +/** + * get_group_selector() - returns the group selector for a group + * @pin_group: the pin group to look up + * + * This is the same as pinctrl_get_group_selector except it doesn't produce an + * error message if the group isn't found or debug messages. + */ +static int get_group_selector(const char *pin_group) +{ + unsigned int group; + + for (group = 0; group < ARRAY_SIZE(tz1090_pdc_groups); ++group) + if (!strcmp(tz1090_pdc_groups[group].name, pin_group)) + return group; + + return -EINVAL; +} + +static int add_map_configs(struct device *dev, + struct pinctrl_map **map, + unsigned int *reserved_maps, unsigned int *num_maps, + const char *group, unsigned long *configs, + unsigned int num_configs) +{ + unsigned long *dup_configs; + enum pinctrl_map_type type; + + if (WARN_ON(*num_maps == *reserved_maps)) + return -ENOSPC; + + dup_configs = kmemdup(configs, num_configs * sizeof(*dup_configs), + GFP_KERNEL); + if (!dup_configs) { + dev_err(dev, "kmemdup(configs) failed\n"); + return -ENOMEM; + } + + /* + * We support both pins and pin groups, but we need to figure out which + * one we have. + */ + if (get_group_selector(group) >= 0) + type = PIN_MAP_TYPE_CONFIGS_GROUP; + else + type = PIN_MAP_TYPE_CONFIGS_PIN; + (*map)[*num_maps].type = type; + (*map)[*num_maps].data.configs.group_or_pin = group; + (*map)[*num_maps].data.configs.configs = dup_configs; + (*map)[*num_maps].data.configs.num_configs = num_configs; + (*num_maps)++; + + return 0; +} + +static void tz1090_pdc_pinctrl_dt_free_map(struct pinctrl_dev *pctldev, + struct pinctrl_map *map, + unsigned int num_maps) +{ + int i; + + for (i = 0; i < num_maps; i++) + if (map[i].type == PIN_MAP_TYPE_CONFIGS_GROUP) + kfree(map[i].data.configs.configs); + + kfree(map); +} + +static int tz1090_pdc_pinctrl_dt_subnode_to_map(struct device *dev, + struct device_node *np, + struct pinctrl_map **map, + unsigned int *reserved_maps, + unsigned int *num_maps) +{ + int ret; + const char *function; + unsigned long *configs = NULL; + unsigned int num_configs = 0; + unsigned int reserve; + struct property *prop; + const char *group; + + ret = of_property_read_string(np, "tz1090,function", &function); + if (ret < 0) { + /* EINVAL=missing, which is fine since it's optional */ + if (ret != -EINVAL) + dev_err(dev, + "could not parse property function\n"); + function = NULL; + } + + ret = pinconf_generic_parse_dt_config(np, &configs, &num_configs); + if (ret) + return ret; + + reserve = 0; + if (function != NULL) + reserve++; + if (num_configs) + reserve++; + ret = of_property_count_strings(np, "tz1090,pins"); + if (ret < 0) { + dev_err(dev, "could not parse property pins\n"); + goto exit; + } + reserve *= ret; + + ret = reserve_map(dev, map, reserved_maps, num_maps, reserve); + if (ret < 0) + goto exit; + + of_property_for_each_string(np, "tz1090,pins", prop, group) { + if (function) { + ret = add_map_mux(map, reserved_maps, num_maps, + group, function); + if (ret < 0) + goto exit; + } + + if (num_configs) { + ret = add_map_configs(dev, map, reserved_maps, + num_maps, group, configs, + num_configs); + if (ret < 0) + goto exit; + } + } + + ret = 0; + +exit: + kfree(configs); + return ret; +} + +static int tz1090_pdc_pinctrl_dt_node_to_map(struct pinctrl_dev *pctldev, + struct device_node *np_config, + struct pinctrl_map **map, + unsigned int *num_maps) +{ + unsigned int reserved_maps; + struct device_node *np; + int ret; + + reserved_maps = 0; + *map = NULL; + *num_maps = 0; + + for_each_child_of_node(np_config, np) { + ret = tz1090_pdc_pinctrl_dt_subnode_to_map(pctldev->dev, np, + map, &reserved_maps, + num_maps); + if (ret < 0) { + tz1090_pdc_pinctrl_dt_free_map(pctldev, *map, + *num_maps); + return ret; + } + } + + return 0; +} + +static struct pinctrl_ops tz1090_pdc_pinctrl_ops = { + .get_groups_count = tz1090_pdc_pinctrl_get_groups_count, + .get_group_name = tz1090_pdc_pinctrl_get_group_name, + .get_group_pins = tz1090_pdc_pinctrl_get_group_pins, +#ifdef CONFIG_DEBUG_FS + .pin_dbg_show = tz1090_pdc_pinctrl_pin_dbg_show, +#endif + .dt_node_to_map = tz1090_pdc_pinctrl_dt_node_to_map, + .dt_free_map = tz1090_pdc_pinctrl_dt_free_map, +}; + +/* + * Pin mux operations + */ + +static int tz1090_pdc_pinctrl_get_funcs_count(struct pinctrl_dev *pctldev) +{ + return ARRAY_SIZE(tz1090_pdc_functions); +} + +static const char *tz1090_pdc_pinctrl_get_func_name(struct pinctrl_dev *pctldev, + unsigned int function) +{ + return tz1090_pdc_functions[function].name; +} + +static int tz1090_pdc_pinctrl_get_func_groups(struct pinctrl_dev *pctldev, + unsigned int function, + const char * const **groups, + unsigned int * const num_groups) +{ + *groups = tz1090_pdc_functions[function].groups; + *num_groups = tz1090_pdc_functions[function].ngroups; + + return 0; +} + +/** + * tz1090_pdc_pinctrl_mux() - update mux bit + * @pmx: Pinmux data + * @grp: Pin mux group + */ +static void tz1090_pdc_pinctrl_mux(struct tz1090_pdc_pmx *pmx, + const struct tz1090_pdc_pingroup *grp) +{ + u32 reg, select; + unsigned int pin_shift = grp->pins[0]; + unsigned long flags; + + /* select = mux && !gpio */ + select = ((pmx->mux_en & ~pmx->gpio_en) >> pin_shift) & 1; + + /* set up the mux */ + __global_lock2(flags); + reg = pmx_read(pmx, grp->reg); + reg &= ~BIT(grp->bit); + reg |= select << grp->bit; + pmx_write(pmx, reg, grp->reg); + __global_unlock2(flags); +} + +static int tz1090_pdc_pinctrl_enable(struct pinctrl_dev *pctldev, + unsigned int function, unsigned int group) +{ + struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev); + const struct tz1090_pdc_pingroup *grp = &tz1090_pdc_groups[group]; + + dev_dbg(pctldev->dev, "%s(func=%u (%s), group=%u (%s))\n", + __func__, + function, tz1090_pdc_functions[function].name, + group, tz1090_pdc_groups[group].name); + + /* is it even a mux? */ + if (grp->drv) + return -EINVAL; + + /* does this group even control the function? */ + if (function != grp->func) + return -EINVAL; + + /* record the pin being muxed and update mux bit */ + spin_lock(&pmx->lock); + pmx->mux_en |= BIT(grp->pins[0]); + tz1090_pdc_pinctrl_mux(pmx, grp); + spin_unlock(&pmx->lock); + return 0; +} + +static void tz1090_pdc_pinctrl_disable(struct pinctrl_dev *pctldev, + unsigned int function, + unsigned int group) +{ + struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev); + const struct tz1090_pdc_pingroup *grp = &tz1090_pdc_groups[group]; + + dev_dbg(pctldev->dev, "%s(func=%u (%s), group=%u (%s))\n", + __func__, + function, tz1090_pdc_functions[function].name, + group, tz1090_pdc_groups[group].name); + + /* is it even a mux? */ + if (grp->drv) + return; + + /* does this group even control the function? */ + if (function != grp->func) + return; + + /* record the pin being unmuxed and update mux bit */ + spin_lock(&pmx->lock); + pmx->mux_en &= ~BIT(grp->pins[0]); + tz1090_pdc_pinctrl_mux(pmx, grp); + spin_unlock(&pmx->lock); +} + +static const struct tz1090_pdc_pingroup *find_mux_group( + struct tz1090_pdc_pmx *pmx, + unsigned int pin) +{ + const struct tz1090_pdc_pingroup *grp; + unsigned int group; + + grp = tz1090_pdc_groups; + for (group = 0; group < ARRAY_SIZE(tz1090_pdc_groups); ++group, ++grp) { + /* only match muxes */ + if (grp->drv) + continue; + + /* with a matching pin */ + if (grp->pins[0] == pin) + return grp; + } + + return NULL; +} + +static int tz1090_pdc_pinctrl_gpio_request_enable( + struct pinctrl_dev *pctldev, + struct pinctrl_gpio_range *range, + unsigned int pin) +{ + struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev); + const struct tz1090_pdc_pingroup *grp = find_mux_group(pmx, pin); + + if (grp) { + /* record the pin in GPIO use and update mux bit */ + spin_lock(&pmx->lock); + pmx->gpio_en |= BIT(pin); + tz1090_pdc_pinctrl_mux(pmx, grp); + spin_unlock(&pmx->lock); + } + return 0; +} + +static void tz1090_pdc_pinctrl_gpio_disable_free( + struct pinctrl_dev *pctldev, + struct pinctrl_gpio_range *range, + unsigned int pin) +{ + struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev); + const struct tz1090_pdc_pingroup *grp = find_mux_group(pmx, pin); + + if (grp) { + /* record the pin not in GPIO use and update mux bit */ + spin_lock(&pmx->lock); + pmx->gpio_en &= ~BIT(pin); + tz1090_pdc_pinctrl_mux(pmx, grp); + spin_unlock(&pmx->lock); + } +} + +static struct pinmux_ops tz1090_pdc_pinmux_ops = { + .get_functions_count = tz1090_pdc_pinctrl_get_funcs_count, + .get_function_name = tz1090_pdc_pinctrl_get_func_name, + .get_function_groups = tz1090_pdc_pinctrl_get_func_groups, + .enable = tz1090_pdc_pinctrl_enable, + .disable = tz1090_pdc_pinctrl_disable, + .gpio_request_enable = tz1090_pdc_pinctrl_gpio_request_enable, + .gpio_disable_free = tz1090_pdc_pinctrl_gpio_disable_free, +}; + +/* + * Pin config operations + */ + +static int tz1090_pdc_pinconf_reg(struct pinctrl_dev *pctldev, + unsigned int pin, + enum pin_config_param param, + bool report_err, + u32 *reg, u32 *width, u32 *mask, u32 *shift, + u32 *val) +{ + /* Find information about parameter's register */ + switch (param) { + case PIN_CONFIG_BIAS_DISABLE: + case PIN_CONFIG_BIAS_HIGH_IMPEDANCE: + *val = REG_PU_PD_TRISTATE; + break; + case PIN_CONFIG_BIAS_PULL_UP: + *val = REG_PU_PD_UP; + break; + case PIN_CONFIG_BIAS_PULL_DOWN: + *val = REG_PU_PD_DOWN; + break; + case PIN_CONFIG_BIAS_BUS_HOLD: + *val = REG_PU_PD_REPEATER; + break; + default: + return -ENOTSUPP; + }; + + /* Only input bias parameters supported */ + *reg = REG_GPIO_CONTROL2; + *shift = REG_GPIO_CONTROL2_PU_PD_S + pin*2; + *width = 2; + + /* Calculate field information */ + *mask = (BIT(*width) - 1) << *shift; + + return 0; +} + +static int tz1090_pdc_pinconf_get(struct pinctrl_dev *pctldev, + unsigned int pin, unsigned long *config) +{ + struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev); + enum pin_config_param param = pinconf_to_config_param(*config); + int ret; + u32 reg, width, mask, shift, val, tmp, arg; + + /* Get register information */ + ret = tz1090_pdc_pinconf_reg(pctldev, pin, param, true, + ®, &width, &mask, &shift, &val); + if (ret < 0) + return ret; + + /* Extract field from register */ + tmp = pmx_read(pmx, reg); + arg = ((tmp & mask) >> shift) == val; + + /* Config not active */ + if (!arg) + return -EINVAL; + + /* And pack config */ + *config = pinconf_to_config_packed(param, arg); + + return 0; +} + +static int tz1090_pdc_pinconf_set(struct pinctrl_dev *pctldev, + unsigned int pin, unsigned long config) +{ + struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev); + enum pin_config_param param = pinconf_to_config_param(config); + unsigned int arg = pinconf_to_config_argument(config); + int ret; + u32 reg, width, mask, shift, val, tmp; + unsigned long flags; + + dev_dbg(pctldev->dev, "%s(pin=%s, config=%#lx)\n", + __func__, tz1090_pdc_pins[pin].name, config); + + /* Get register information */ + ret = tz1090_pdc_pinconf_reg(pctldev, pin, param, true, + ®, &width, &mask, &shift, &val); + if (ret < 0) + return ret; + + /* Unpack argument and range check it */ + if (arg > 1) { + dev_dbg(pctldev->dev, "%s: arg %u out of range\n", + __func__, arg); + return -EINVAL; + } + + /* Write register field */ + __global_lock2(flags); + tmp = pmx_read(pmx, reg); + tmp &= ~mask; + if (arg) + tmp |= val << shift; + pmx_write(pmx, tmp, reg); + __global_unlock2(flags); + + return 0; +} + +static const int tz1090_pdc_boolean_map[] = { + [0] = -EINVAL, + [1] = 1, +}; + +static const int tz1090_pdc_dr_map[] = { + [REG_DR_2mA] = 2, + [REG_DR_4mA] = 4, + [REG_DR_8mA] = 8, + [REG_DR_12mA] = 12, +}; + +static int tz1090_pdc_pinconf_group_reg(struct pinctrl_dev *pctldev, + const struct tz1090_pdc_pingroup *g, + enum pin_config_param param, + bool report_err, u32 *reg, u32 *width, + u32 *mask, u32 *shift, const int **map) +{ + /* Drive configuration applies in groups, but not to all groups. */ + if (!g->drv) { + if (report_err) + dev_dbg(pctldev->dev, + "%s: group %s has no drive control\n", + __func__, g->name); + return -ENOTSUPP; + } + + /* Find information about drive parameter's register */ + *reg = REG_GPIO_CONTROL2; + switch (param) { + case PIN_CONFIG_INPUT_SCHMITT_ENABLE: + *shift = REG_GPIO_CONTROL2_PDC_SCHMITT_S; + *width = 1; + *map = tz1090_pdc_boolean_map; + break; + case PIN_CONFIG_SLEW_RATE: + *shift = REG_GPIO_CONTROL2_PDC_SR_S; + *width = 1; + *map = tz1090_pdc_boolean_map; + break; + case PIN_CONFIG_DRIVE_STRENGTH: + *shift = REG_GPIO_CONTROL2_PDC_DR_S; + *width = 2; + *map = tz1090_pdc_dr_map; + break; + case PIN_CONFIG_LOW_POWER_MODE: + *shift = REG_GPIO_CONTROL2_PDC_POS_S; + *width = 1; + *map = tz1090_pdc_boolean_map; + break; + default: + return -ENOTSUPP; + }; + + /* Calculate field information */ + *mask = (BIT(*width) - 1) << *shift; + + return 0; +} + +static int tz1090_pdc_pinconf_group_get(struct pinctrl_dev *pctldev, + unsigned int group, + unsigned long *config) +{ + struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev); + const struct tz1090_pdc_pingroup *g = &tz1090_pdc_groups[group]; + enum pin_config_param param = pinconf_to_config_param(*config); + int ret, arg; + u32 reg, width, mask, shift, val; + const int *map; + + /* Get register information */ + ret = tz1090_pdc_pinconf_group_reg(pctldev, g, param, true, + ®, &width, &mask, &shift, &map); + if (ret < 0) + return ret; + + /* Extract field from register */ + val = pmx_read(pmx, reg); + arg = map[(val & mask) >> shift]; + if (arg < 0) + return arg; + + /* And pack config */ + *config = pinconf_to_config_packed(param, arg); + + return 0; +} + +static int tz1090_pdc_pinconf_group_set(struct pinctrl_dev *pctldev, + unsigned int group, + unsigned long config) +{ + struct tz1090_pdc_pmx *pmx = pinctrl_dev_get_drvdata(pctldev); + const struct tz1090_pdc_pingroup *g = &tz1090_pdc_groups[group]; + enum pin_config_param param = pinconf_to_config_param(config); + const unsigned int *pit; + unsigned int i; + int ret, arg; + u32 reg, width, mask, shift, val; + unsigned long flags; + const int *map; + + dev_dbg(pctldev->dev, "%s(group=%s, config=%#lx)\n", + __func__, g->name, config); + + /* Get register information */ + ret = tz1090_pdc_pinconf_group_reg(pctldev, g, param, true, + ®, &width, &mask, &shift, &map); + if (ret < 0) { + /* + * Maybe we're trying to set a per-pin configuration of a group, + * so do the pins one by one. This is mainly as a convenience. + */ + for (i = 0, pit = g->pins; i < g->npins; ++i, ++pit) { + ret = tz1090_pdc_pinconf_set(pctldev, *pit, config); + if (ret) + return ret; + } + return 0; + } + + /* Unpack argument and map it to register value */ + arg = pinconf_to_config_argument(config); + for (i = 0; i < BIT(width); ++i) { + if (map[i] == arg || (map[i] == -EINVAL && !arg)) { + /* Write register field */ + __global_lock2(flags); + val = pmx_read(pmx, reg); + val &= ~mask; + val |= i << shift; + pmx_write(pmx, val, reg); + __global_unlock2(flags); + return 0; + } + } + + dev_dbg(pctldev->dev, "%s: arg %u not supported\n", + __func__, arg); + return 0; +} + +static struct pinconf_ops tz1090_pdc_pinconf_ops = { + .is_generic = true, + .pin_config_get = tz1090_pdc_pinconf_get, + .pin_config_set = tz1090_pdc_pinconf_set, + .pin_config_group_get = tz1090_pdc_pinconf_group_get, + .pin_config_group_set = tz1090_pdc_pinconf_group_set, + .pin_config_config_dbg_show = pinconf_generic_dump_config, +}; + +/* + * Pin control driver setup + */ + +static struct pinctrl_desc tz1090_pdc_pinctrl_desc = { + .pctlops = &tz1090_pdc_pinctrl_ops, + .pmxops = &tz1090_pdc_pinmux_ops, + .confops = &tz1090_pdc_pinconf_ops, + .owner = THIS_MODULE, +}; + +static int tz1090_pdc_pinctrl_probe(struct platform_device *pdev) +{ + struct tz1090_pdc_pmx *pmx; + struct resource *res; + + pmx = devm_kzalloc(&pdev->dev, sizeof(*pmx), GFP_KERNEL); + if (!pmx) { + dev_err(&pdev->dev, "Can't alloc tz1090_pdc_pmx\n"); + return -ENOMEM; + } + pmx->dev = &pdev->dev; + spin_lock_init(&pmx->lock); + + tz1090_pdc_pinctrl_desc.name = dev_name(&pdev->dev); + tz1090_pdc_pinctrl_desc.pins = tz1090_pdc_pins; + tz1090_pdc_pinctrl_desc.npins = ARRAY_SIZE(tz1090_pdc_pins); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "Missing MEM resource\n"); + return -ENODEV; + } + + if (!devm_request_mem_region(&pdev->dev, res->start, + resource_size(res), + dev_name(&pdev->dev))) { + dev_err(&pdev->dev, + "Couldn't request MEM resource\n"); + return -ENODEV; + } + + pmx->regs = devm_ioremap(&pdev->dev, res->start, + resource_size(res)); + if (!pmx->regs) { + dev_err(&pdev->dev, "Couldn't ioremap regs\n"); + return -ENODEV; + } + + pmx->pctl = pinctrl_register(&tz1090_pdc_pinctrl_desc, &pdev->dev, pmx); + if (!pmx->pctl) { + dev_err(&pdev->dev, "Couldn't register pinctrl driver\n"); + return -ENODEV; + } + + platform_set_drvdata(pdev, pmx); + + dev_info(&pdev->dev, "TZ1090 PDC pinctrl driver initialised\n"); + + return 0; +} + +static int tz1090_pdc_pinctrl_remove(struct platform_device *pdev) +{ + struct tz1090_pdc_pmx *pmx = platform_get_drvdata(pdev); + + pinctrl_unregister(pmx->pctl); + + return 0; +} + +static struct of_device_id tz1090_pdc_pinctrl_of_match[] = { + { .compatible = "img,tz1090-pdc-pinctrl", }, + { }, +}; + +static struct platform_driver tz1090_pdc_pinctrl_driver = { + .driver = { + .name = "tz1090-pdc-pinctrl", + .owner = THIS_MODULE, + .of_match_table = tz1090_pdc_pinctrl_of_match, + }, + .probe = tz1090_pdc_pinctrl_probe, + .remove = tz1090_pdc_pinctrl_remove, +}; + +static int __init tz1090_pdc_pinctrl_init(void) +{ + return platform_driver_register(&tz1090_pdc_pinctrl_driver); +} +arch_initcall(tz1090_pdc_pinctrl_init); + +static void __exit tz1090_pdc_pinctrl_exit(void) +{ + platform_driver_unregister(&tz1090_pdc_pinctrl_driver); +} +module_exit(tz1090_pdc_pinctrl_exit); + +MODULE_AUTHOR("Imagination Technologies Ltd."); +MODULE_DESCRIPTION("Toumaz Xenif TZ1090 PDC pinctrl driver"); +MODULE_LICENSE("GPL v2"); +MODULE_DEVICE_TABLE(of, tz1090_pdc_pinctrl_of_match);