MIPS: sibyte: Remove unused config option SIBYTE_BCM1x55

SIBYTE_BCM1x55 is not selected anywhere, so let's get rid of it.

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

arch/mips/Kbuild.platforms

@@ -29,7 +29,6 @@ platform-$(CONFIG_SGI_IP30)		+= sgi-ip30/
 platform-$(CONFIG_SGI_IP32)		+= sgi-ip32/
 platform-$(CONFIG_SIBYTE_BCM112X)	+= sibyte/
 platform-$(CONFIG_SIBYTE_SB1250)	+= sibyte/
-platform-$(CONFIG_SIBYTE_BCM1x55)	+= sibyte/
 platform-$(CONFIG_SIBYTE_BCM1x80)	+= sibyte/
 platform-$(CONFIG_SNI_RM)		+= sni/
 platform-$(CONFIG_MACH_TX49XX)		+= txx9/

arch/mips/sibyte/Kconfig

@@ -58,16 +58,6 @@ config SIBYTE_BCM1x80
 	select SIBYTE_SB1xxx_SOC
 	select SYS_SUPPORTS_SMP
 
-config SIBYTE_BCM1x55
-	bool
-	select CEVT_BCM1480
-	select CSRC_BCM1480
-	select HAVE_PCI
-	select IRQ_MIPS_CPU
-	select SIBYTE_SB1xxx_SOC
-	select SIBYTE_HAS_ZBUS_PROFILING
-	select SYS_SUPPORTS_SMP
-
 config SIBYTE_SB1xxx_SOC
 	bool
 	select IRQ_MIPS_CPU
@@ -143,8 +133,7 @@ config SIBYTE_CFE_CONSOLE
 config SIBYTE_BUS_WATCHER
 	bool "Support for Bus Watcher statistics"
 	depends on SIBYTE_SB1xxx_SOC && \
-		(SIBYTE_BCM112X || SIBYTE_SB1250 || \
-		 SIBYTE_BCM1x55 || SIBYTE_BCM1x80)
+		(SIBYTE_BCM112X || SIBYTE_SB1250 || SIBYTE_BCM1x80)
 	help
 	  Handle and keep statistics on the bus error interrupts (COR_ECC,
 	  BAD_ECC, IO_BUS).

arch/mips/sibyte/Makefile

@@ -6,8 +6,6 @@ obj-$(CONFIG_SIBYTE_BCM112X)	+= sb1250/
 obj-$(CONFIG_SIBYTE_BCM112X)	+= common/
 obj-$(CONFIG_SIBYTE_SB1250)	+= sb1250/
 obj-$(CONFIG_SIBYTE_SB1250)	+= common/
-obj-$(CONFIG_SIBYTE_BCM1x55)	+= bcm1480/
-obj-$(CONFIG_SIBYTE_BCM1x55)	+= common/
 obj-$(CONFIG_SIBYTE_BCM1x80)	+= bcm1480/
 obj-$(CONFIG_SIBYTE_BCM1x80)	+= common/
 

arch/mips/sibyte/Platform

@@ -13,10 +13,6 @@ cflags-$(CONFIG_SIBYTE_SB1250)	+=					\
 		-I$(srctree)/arch/mips/include/asm/mach-sibyte		\
 		-DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1250_112x_ALL
 
-cflags-$(CONFIG_SIBYTE_BCM1x55) +=					\
-		-I$(srctree)/arch/mips/include/asm/mach-sibyte		\
-		-DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1480_ALL
-
 cflags-$(CONFIG_SIBYTE_BCM1x80) +=					\
 		-I$(srctree)/arch/mips/include/asm/mach-sibyte		\
 		-DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1480_ALL

arch/mips/sibyte/common/bus_watcher.c

@@ -24,7 +24,7 @@
 #include <asm/sibyte/sb1250_regs.h>
 #include <asm/sibyte/sb1250_int.h>
 #include <asm/sibyte/sb1250_scd.h>
-#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#ifdef CONFIG_SIBYTE_BCM1x80
 #include <asm/sibyte/bcm1480_regs.h>
 #endif
 
@@ -71,7 +71,7 @@ void check_bus_watcher(void)
 #if defined(CONFIG_SIBYTE_BCM112X) || defined(CONFIG_SIBYTE_SB1250)
 	/* Use non-destructive register */
 	status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS_DEBUG));
-#elif defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#elif defined(CONFIG_SIBYTE_BCM1x80)
 	/* Use non-destructive register */
 	/* Same as 1250 except BUS_ERR_STATUS_DEBUG is in a different place. */
 	status = csr_in32(IOADDR(A_BCM1480_BUS_ERR_STATUS_DEBUG));

arch/mips/sibyte/common/cfe.c

@@ -295,7 +295,7 @@ void __init prom_init(void)
 #if defined(CONFIG_SIBYTE_BCM112X) || defined(CONFIG_SIBYTE_SB1250)
 	register_smp_ops(&sb_smp_ops);
 #endif
-#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#ifdef CONFIG_SIBYTE_BCM1x80
 	register_smp_ops(&bcm1480_smp_ops);
 #endif
 }

arch/mips/sibyte/common/sb_tbprof.c

@@ -23,7 +23,7 @@
 #include <asm/io.h>
 #include <asm/sibyte/sb1250.h>
 
-#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#ifdef CONFIG_SIBYTE_BCM1x80
 #include <asm/sibyte/bcm1480_regs.h>
 #include <asm/sibyte/bcm1480_scd.h>
 #include <asm/sibyte/bcm1480_int.h>
@@ -35,7 +35,7 @@
 #error invalid SiByte UART configuration
 #endif
 
-#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#ifdef CONFIG_SIBYTE_BCM1x80
 #undef K_INT_TRACE_FREEZE
 #define K_INT_TRACE_FREEZE K_BCM1480_INT_TRACE_FREEZE
 #undef K_INT_PERF_CNT
@@ -157,7 +157,7 @@ static void arm_tb(void)
 	 * a previous interrupt request.  This means that bus profiling
 	 * requires ALL of the SCD perf counters.
 	 */
-#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#ifdef CONFIG_SIBYTE_BCM1x80
 	__raw_writeq((scdperfcnt & ~M_SPC_CFG_SRC1) |
 						/* keep counters 0,2,3,4,5,6,7 as is */
 		     V_SPC_CFG_SRC1(1),		/* counter 1 counts cycles */
@@ -290,7 +290,7 @@ static int sbprof_zbprof_start(struct file *filp)
 	 *  pass them through.	I am exploiting my knowledge that
 	 *  cp0_status masks out IP[5]. krw
 	 */
-#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#ifdef CONFIG_SIBYTE_BCM1x80
 	__raw_writeq(K_BCM1480_INT_MAP_I3,
 		     IOADDR(A_BCM1480_IMR_REGISTER(0, R_BCM1480_IMR_INTERRUPT_MAP_BASE_L) +
 			    ((K_BCM1480_INT_PERF_CNT & 0x3f) << 3)));
@@ -343,7 +343,7 @@ static int sbprof_zbprof_start(struct file *filp)
 	__raw_writeq(0, IOADDR(A_SCD_TRACE_SEQUENCE_7));
 
 	/* Now indicate the PERF_CNT interrupt as a trace-relevant interrupt */
-#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#ifdef CONFIG_SIBYTE_BCM1x80
 	__raw_writeq(1ULL << (K_BCM1480_INT_PERF_CNT & 0x3f),
 		     IOADDR(A_BCM1480_IMR_REGISTER(0, R_BCM1480_IMR_INTERRUPT_TRACE_L)));
 #else

arch/mips/sibyte/swarm/setup.c

@@ -24,7 +24,7 @@
 #include <asm/time.h>
 #include <asm/traps.h>
 #include <asm/sibyte/sb1250.h>
-#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#ifdef CONFIG_SIBYTE_BCM1x80
 #include <asm/sibyte/bcm1480_regs.h>
 #elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X)
 #include <asm/sibyte/sb1250_regs.h>
@@ -34,7 +34,7 @@
 #include <asm/sibyte/sb1250_genbus.h>
 #include <asm/sibyte/board.h>
 
-#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#ifdef CONFIG_SIBYTE_BCM1x80
 extern void bcm1480_setup(void);
 #elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X)
 extern void sb1250_setup(void);
@@ -114,7 +114,7 @@ int update_persistent_clock64(struct timespec64 now)
 
 void __init plat_mem_setup(void)
 {
-#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#ifdef CONFIG_SIBYTE_BCM1x80
 	bcm1480_setup();
 #elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X)
 	sb1250_setup();