media: Documentation: media: Improve camera sensor documentation
Modernise the documentation to make it more precise and update the use of
pixel rate control and various other changes. In particular:
- Use non-proportional font for file names, properties as well as
controls.
- The unit of the HBLANK control is pixels, not lines.
- The unit of PIXEL_RATE control is pixels per second, not Hz.
- Merge common requirements for CSI-2 and parallel busses.
- Include all DT properties needed for assigned clocks.
- Fix referencing the link rate control.
- SMIA driver's new name is CCS driver.
- The PIXEL_RATE control denotes pixel rate on the pixel array on camera
sensors. Do not suggest it is used to tell the maximum pixel rate on the
bus anymore.
- Improve ReST syntax (plain struct and function names).
- Remove the suggestion to use s_power() in receiver drivers.
- Make MIPI website URL use HTTPS, add Wikipedia links to BT.601 and
BT.656.
Fixes: e4cf8c58af ("media: Documentation: media: Document how to write camera sensor drivers")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This commit is contained in:
Sakari Ailus
Mauro Carvalho Chehab
Родитель
0368e7d2cd
Коммит
b9a5433642
|
|
@ -3,10 +3,10 @@
|
|||
Writing camera sensor drivers
|
||||
=============================
|
||||
|
||||
CSI-2
|
||||
-----
|
||||
CSI-2 and parallel (BT.601 and BT.656) busses
|
||||
---------------------------------------------
|
||||
|
||||
Please see what is written on :ref:`MIPI_CSI_2`.
|
||||
Please see :ref:`transmitter-receiver`.
|
||||
|
||||
Handling clocks
|
||||
---------------
|
||||
|
|
@ -26,15 +26,16 @@ user.
|
|||
ACPI
|
||||
~~~~
|
||||
|
||||
Read the "clock-frequency" _DSD property to denote the frequency. The driver can
|
||||
rely on this frequency being used.
|
||||
Read the ``clock-frequency`` _DSD property to denote the frequency. The driver
|
||||
can rely on this frequency being used.
|
||||
|
||||
Devicetree
|
||||
~~~~~~~~~~
|
||||
|
||||
The currently preferred way to achieve this is using "assigned-clock-rates"
|
||||
property. See Documentation/devicetree/bindings/clock/clock-bindings.txt for
|
||||
more information. The driver then gets the frequency using clk_get_rate().
|
||||
The currently preferred way to achieve this is using ``assigned-clocks``,
|
||||
``assigned-clock-parents`` and ``assigned-clock-rates`` properties. See
|
||||
``Documentation/devicetree/bindings/clock/clock-bindings.txt`` for more
|
||||
information. The driver then gets the frequency using ``clk_get_rate()``.
|
||||
|
||||
This approach has the drawback that there's no guarantee that the frequency
|
||||
hasn't been modified directly or indirectly by another driver, or supported by
|
||||
|
|
@ -55,7 +56,7 @@ processing pipeline as one or more sub-devices with different cropping and
|
|||
scaling configurations. The output size of the device is the result of a series
|
||||
of cropping and scaling operations from the device's pixel array's size.
|
||||
|
||||
An example of such a driver is the smiapp driver (see drivers/media/i2c/smiapp).
|
||||
An example of such a driver is the CCS driver (see ``drivers/media/i2c/ccs``).
|
||||
|
||||
Register list based drivers
|
||||
~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||||
|
|
@ -67,7 +68,7 @@ level are independent. How a driver picks such configuration is based on the
|
|||
format set on a source pad at the end of the device's internal pipeline.
|
||||
|
||||
Most sensor drivers are implemented this way, see e.g.
|
||||
drivers/media/i2c/imx319.c for an example.
|
||||
``drivers/media/i2c/imx319.c`` for an example.
|
||||
|
||||
Frame interval configuration
|
||||
----------------------------
|
||||
|
|
@ -94,9 +95,10 @@ large variety of devices beyond camera sensors. Devices that have no analogue
|
|||
crop, use the full source image size, i.e. pixel array size.
|
||||
|
||||
Horizontal and vertical blanking are specified by ``V4L2_CID_HBLANK`` and
|
||||
``V4L2_CID_VBLANK``, respectively. The unit of these controls are lines. The
|
||||
pixel rate is specified by ``V4L2_CID_PIXEL_RATE`` in the same sub-device. The
|
||||
unit of that control is Hz.
|
||||
``V4L2_CID_VBLANK``, respectively. The unit of the ``V4L2_CID_HBLANK`` control
|
||||
is pixels and the unit of the ``V4L2_CID_VBLANK`` is lines. The pixel rate in
|
||||
the sensor's **pixel array** is specified by ``V4L2_CID_PIXEL_RATE`` in the same
|
||||
sub-device. The unit of that control is pixels per second.
|
||||
|
||||
Register list based drivers need to implement read-only sub-device nodes for the
|
||||
purpose. Devices that are not register list based need these to configure the
|
||||
|
|
@ -125,14 +127,14 @@ general, the device must be powered on at least when its registers are being
|
|||
accessed and when it is streaming.
|
||||
|
||||
Existing camera sensor drivers may rely on the old
|
||||
:c:type:`v4l2_subdev_core_ops`->s_power() callback for bridge or ISP drivers to
|
||||
struct v4l2_subdev_core_ops->s_power() callback for bridge or ISP drivers to
|
||||
manage their power state. This is however **deprecated**. If you feel you need
|
||||
to begin calling an s_power from an ISP or a bridge driver, instead please add
|
||||
runtime PM support to the sensor driver you are using. Likewise, new drivers
|
||||
should not use s_power.
|
||||
|
||||
Please see examples in e.g. ``drivers/media/i2c/ov8856.c`` and
|
||||
``drivers/media/i2c/smiapp/smiapp-core.c``. The two drivers work in both ACPI
|
||||
``drivers/media/i2c/ccs/ccs-core.c``. The two drivers work in both ACPI
|
||||
and DT based systems.
|
||||
|
||||
Control framework
|
||||
|
|
@ -149,16 +151,3 @@ used to obtain device's power state after the power state transition:
|
|||
The function returns a non-zero value if it succeeded getting the power count or
|
||||
runtime PM was disabled, in either of which cases the driver may proceed to
|
||||
access the device.
|
||||
|
||||
Controls
|
||||
--------
|
||||
|
||||
For camera sensors that are connected to a bus where transmitter and receiver
|
||||
require common configuration set by drivers, such as CSI-2 or parallel (BT.601
|
||||
or BT.656) bus, the ``V4L2_CID_LINK_FREQ`` control is mandatory on transmitter
|
||||
drivers. Receiver drivers can use the ``V4L2_CID_LINK_FREQ`` to query the
|
||||
frequency used on the bus.
|
||||
|
||||
The transmitter drivers should also implement ``V4L2_CID_PIXEL_RATE`` control in
|
||||
order to tell the maximum pixel rate to the receiver. This is required on raw
|
||||
camera sensors.
|
||||
|
|
|
|||
|
|
@ -1,94 +0,0 @@
|
|||
.. SPDX-License-Identifier: GPL-2.0
|
||||
|
||||
.. _MIPI_CSI_2:
|
||||
|
||||
MIPI CSI-2
|
||||
==========
|
||||
|
||||
CSI-2 is a data bus intended for transferring images from cameras to
|
||||
the host SoC. It is defined by the `MIPI alliance`_.
|
||||
|
||||
.. _`MIPI alliance`: http://www.mipi.org/
|
||||
|
||||
Media bus formats
|
||||
-----------------
|
||||
|
||||
See :ref:`v4l2-mbus-pixelcode` for details on which media bus formats should
|
||||
be used for CSI-2 interfaces.
|
||||
|
||||
Transmitter drivers
|
||||
-------------------
|
||||
|
||||
CSI-2 transmitter, such as a sensor or a TV tuner, drivers need to
|
||||
provide the CSI-2 receiver with information on the CSI-2 bus
|
||||
configuration. These include the V4L2_CID_LINK_FREQ and
|
||||
V4L2_CID_PIXEL_RATE controls and
|
||||
(:c:type:`v4l2_subdev_video_ops`->s_stream() callback). These
|
||||
interface elements must be present on the sub-device represents the
|
||||
CSI-2 transmitter.
|
||||
|
||||
The V4L2_CID_LINK_FREQ control is used to tell the receiver driver the
|
||||
frequency (and not the symbol rate) of the link. The V4L2_CID_PIXEL_RATE
|
||||
control may be used by the receiver to obtain the pixel rate the transmitter
|
||||
uses. The :c:type:`v4l2_subdev_video_ops`->s_stream() callback provides an
|
||||
ability to start and stop the stream.
|
||||
|
||||
The value of the V4L2_CID_PIXEL_RATE is calculated as follows::
|
||||
|
||||
pixel_rate = link_freq * 2 * nr_of_lanes * 16 / k / bits_per_sample
|
||||
|
||||
where
|
||||
|
||||
.. list-table:: variables in pixel rate calculation
|
||||
:header-rows: 1
|
||||
|
||||
* - variable or constant
|
||||
- description
|
||||
* - link_freq
|
||||
- The value of the V4L2_CID_LINK_FREQ integer64 menu item.
|
||||
* - nr_of_lanes
|
||||
- Number of data lanes used on the CSI-2 link. This can
|
||||
be obtained from the OF endpoint configuration.
|
||||
* - 2
|
||||
- Two bits are transferred per clock cycle per lane.
|
||||
* - bits_per_sample
|
||||
- Number of bits per sample.
|
||||
* - k
|
||||
- 16 for D-PHY and 7 for C-PHY
|
||||
|
||||
The transmitter drivers must, if possible, configure the CSI-2
|
||||
transmitter to *LP-11 mode* whenever the transmitter is powered on but
|
||||
not active, and maintain *LP-11 mode* until stream on. Only at stream
|
||||
on should the transmitter activate the clock on the clock lane and
|
||||
transition to *HS mode*.
|
||||
|
||||
Some transmitters do this automatically but some have to be explicitly
|
||||
programmed to do so, and some are unable to do so altogether due to
|
||||
hardware constraints.
|
||||
|
||||
Stopping the transmitter
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
A transmitter stops sending the stream of images as a result of
|
||||
calling the ``.s_stream()`` callback. Some transmitters may stop the
|
||||
stream at a frame boundary whereas others stop immediately,
|
||||
effectively leaving the current frame unfinished. The receiver driver
|
||||
should not make assumptions either way, but function properly in both
|
||||
cases.
|
||||
|
||||
Receiver drivers
|
||||
----------------
|
||||
|
||||
Before the receiver driver may enable the CSI-2 transmitter by using
|
||||
the :c:type:`v4l2_subdev_video_ops`->s_stream(), it must have powered
|
||||
the transmitter up by using the
|
||||
:c:type:`v4l2_subdev_core_ops`->s_power() callback. This may take
|
||||
place either indirectly by using :c:func:`v4l2_pipeline_pm_get` or
|
||||
directly.
|
||||
|
||||
Formats
|
||||
-------
|
||||
|
||||
The media bus pixel codes document parallel formats. Should the pixel data be
|
||||
transported over a serial bus, the media bus pixel code that describes a
|
||||
parallel format that transfers a sample on a single clock cycle is used.
|
||||
|
|
@ -37,7 +37,7 @@ Documentation/userspace-api/media/index.rst
|
|||
rc-core
|
||||
mc-core
|
||||
cec-core
|
||||
csi2
|
||||
tx-rx
|
||||
camera-sensor
|
||||
|
||||
drivers/index
|
||||
|
|
|
|||
|
|
@ -0,0 +1,117 @@
|
|||
.. SPDX-License-Identifier: GPL-2.0
|
||||
|
||||
.. _transmitter-receiver:
|
||||
|
||||
Pixel data transmitter and receiver drivers
|
||||
===========================================
|
||||
|
||||
V4L2 supports various devices that transmit and receiver pixel data. Examples of
|
||||
these devices include a camera sensor, a TV tuner and a parallel or a CSI-2
|
||||
receiver in an SoC.
|
||||
|
||||
Bus types
|
||||
---------
|
||||
|
||||
The following busses are the most common. This section discusses these two only.
|
||||
|
||||
MIPI CSI-2
|
||||
^^^^^^^^^^
|
||||
|
||||
CSI-2 is a data bus intended for transferring images from cameras to
|
||||
the host SoC. It is defined by the `MIPI alliance`_.
|
||||
|
||||
.. _`MIPI alliance`: https://www.mipi.org/
|
||||
|
||||
Parallel
|
||||
^^^^^^^^
|
||||
|
||||
`BT.601`_ and `BT.656`_ are the most common parallel busses.
|
||||
|
||||
.. _`BT.601`: https://en.wikipedia.org/wiki/Rec._601
|
||||
.. _`BT.656`: https://en.wikipedia.org/wiki/ITU-R_BT.656
|
||||
|
||||
Transmitter drivers
|
||||
-------------------
|
||||
|
||||
Transmitter drivers generally need to provide the receiver drivers with the
|
||||
configuration of the transmitter. What is required depends on the type of the
|
||||
bus. These are common for both busses.
|
||||
|
||||
Media bus pixel code
|
||||
^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
See :ref:`v4l2-mbus-pixelcode`.
|
||||
|
||||
Link frequency
|
||||
^^^^^^^^^^^^^^
|
||||
|
||||
The :ref:`V4L2_CID_LINK_FREQ <v4l2-cid-link-freq>` control is used to tell the
|
||||
receiver the frequency of the bus (i.e. it is not the same as the symbol rate).
|
||||
|
||||
``.s_stream()`` callback
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
The struct struct v4l2_subdev_video_ops->s_stream() callback is used by the
|
||||
receiver driver to control the transmitter driver's streaming state.
|
||||
|
||||
|
||||
CSI-2 transmitter drivers
|
||||
-------------------------
|
||||
|
||||
Pixel rate
|
||||
^^^^^^^^^^
|
||||
|
||||
The pixel rate on the bus is calculated as follows::
|
||||
|
||||
pixel_rate = link_freq * 2 * nr_of_lanes * 16 / k / bits_per_sample
|
||||
|
||||
where
|
||||
|
||||
.. list-table:: variables in pixel rate calculation
|
||||
:header-rows: 1
|
||||
|
||||
* - variable or constant
|
||||
- description
|
||||
* - link_freq
|
||||
- The value of the ``V4L2_CID_LINK_FREQ`` integer64 menu item.
|
||||
* - nr_of_lanes
|
||||
- Number of data lanes used on the CSI-2 link. This can
|
||||
be obtained from the OF endpoint configuration.
|
||||
* - 2
|
||||
- Data is transferred on both rising and falling edge of the signal.
|
||||
* - bits_per_sample
|
||||
- Number of bits per sample.
|
||||
* - k
|
||||
- 16 for D-PHY and 7 for C-PHY
|
||||
|
||||
.. note::
|
||||
|
||||
The pixel rate calculated this way is **not** the same thing as the
|
||||
pixel rate on the camera sensor's pixel array which is indicated by the
|
||||
:ref:`V4L2_CID_PIXEL_RATE <v4l2-cid-pixel-rate>` control.
|
||||
|
||||
LP-11 and LP-111 modes
|
||||
^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
The transmitter drivers must, if possible, configure the CSI-2 transmitter to
|
||||
*LP-11 or LP-111 mode* whenever the transmitter is powered on but not active,
|
||||
and maintain *LP-11 or LP-111 mode* until stream on. Only at stream on should
|
||||
the transmitter activate the clock on the clock lane and transition to *HS
|
||||
mode*.
|
||||
|
||||
Some transmitters do this automatically but some have to be explicitly
|
||||
programmed to do so, and some are unable to do so altogether due to
|
||||
hardware constraints.
|
||||
|
||||
The receiver thus need to be configured to expect LP-11 or LP-111 mode from the
|
||||
transmitter before the transmitter driver's ``.s_stream()`` op is called.
|
||||
|
||||
Stopping the transmitter
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
A transmitter stops sending the stream of images as a result of
|
||||
calling the ``.s_stream()`` callback. Some transmitters may stop the
|
||||
stream at a frame boundary whereas others stop immediately,
|
||||
effectively leaving the current frame unfinished. The receiver driver
|
||||
should not make assumptions either way, but function properly in both
|
||||
cases.
|
||||
|
|
@ -20,6 +20,8 @@ Image Process Control IDs
|
|||
``V4L2_CID_IMAGE_PROC_CLASS (class)``
|
||||
The IMAGE_PROC class descriptor.
|
||||
|
||||
.. _v4l2-cid-link-freq:
|
||||
|
||||
``V4L2_CID_LINK_FREQ (integer menu)``
|
||||
Data bus frequency. Together with the media bus pixel code, bus type
|
||||
(clock cycles per sample), the data bus frequency defines the pixel
|
||||
|
|
|
|||
Загрузка…
Ссылка в новой задаче