diff --git a/CREDITS b/CREDITS index 2ef5dceef324..ec7e6c7fdd1b 100644 --- a/CREDITS +++ b/CREDITS @@ -2049,6 +2049,10 @@ D: pirq addr, CS5535 alsa audio driver S: Gurgaon, India S: Kuala Lumpur, Malaysia +N: Mohit Kumar +D: ST Microelectronics SPEAr13xx PCI host bridge driver +D: Synopsys Designware PCI host bridge driver + N: Gabor Kuti M: seasons@falcon.sch.bme.hu M: seasons@makosteszta.sote.hu @@ -3705,6 +3709,13 @@ N: Dirk Verworner D: Co-author of German book ``Linux-Kernel-Programmierung'' D: Co-founder of Berlin Linux User Group +N: Andrew Victor +E: linux@maxim.org.za +W: http://maxim.org.za/at91_26.html +D: First maintainer of Atmel ARM-based SoC, aka AT91 +D: Introduced support for at91rm9200, the first chip of AT91 family +S: South Africa + N: Riku Voipio E: riku.voipio@iki.fi D: Author of PCA9532 LED and Fintek f75375s hwmon driver diff --git a/Documentation/ABI/testing/sysfs-class-mtd b/Documentation/ABI/testing/sysfs-class-mtd index 76ee192f80a0..3b5c3bca9186 100644 --- a/Documentation/ABI/testing/sysfs-class-mtd +++ b/Documentation/ABI/testing/sysfs-class-mtd @@ -222,3 +222,13 @@ Description: The number of blocks that are marked as reserved, if any, in this partition. These are typically used to store the in-flash bad block table (BBT). + +What: /sys/class/mtd/mtdX/offset +Date: March 2015 +KernelVersion: 4.1 +Contact: linux-mtd@lists.infradead.org +Description: + For a partition, the offset of that partition from the start + of the master device in bytes. This attribute is absent on + main devices, so it can be used to distinguish between + partitions and devices that aren't partitions. diff --git a/Documentation/ABI/testing/sysfs-driver-toshiba_acpi b/Documentation/ABI/testing/sysfs-driver-toshiba_acpi index ca9c71a531c5..eed922ef42e5 100644 --- a/Documentation/ABI/testing/sysfs-driver-toshiba_acpi +++ b/Documentation/ABI/testing/sysfs-driver-toshiba_acpi @@ -8,9 +8,11 @@ Description: This file controls the keyboard backlight operation mode, valid * 0x2 -> AUTO (also called TIMER) * 0x8 -> ON * 0x10 -> OFF - Note that the kernel 3.16 onwards this file accepts all listed + Note that from kernel 3.16 onwards this file accepts all listed parameters, kernel 3.15 only accepts the first two (FN-Z and AUTO). + Also note that toggling this value on type 1 devices, requires + a reboot for changes to take effect. Users: KToshiba What: /sys/devices/LNXSYSTM:00/LNXSYBUS:00/TOS{1900,620{0,7,8}}:00/kbd_backlight_timeout @@ -67,15 +69,72 @@ Description: This file shows the current keyboard backlight type, * 2 -> Type 2, supporting modes TIMER, ON and OFF Users: KToshiba +What: /sys/devices/LNXSYSTM:00/LNXSYBUS:00/TOS{1900,620{0,7,8}}:00/usb_sleep_charge +Date: January 23, 2015 +KernelVersion: 4.0 +Contact: Azael Avalos +Description: This file controls the USB Sleep & Charge charging mode, which + can be: + * 0 -> Disabled (0x00) + * 1 -> Alternate (0x09) + * 2 -> Auto (0x21) + * 3 -> Typical (0x11) + Note that from kernel 4.1 onwards this file accepts all listed + values, kernel 4.0 only supports the first three. + Note that this feature only works when connected to power, if + you want to use it under battery, see the entry named + "sleep_functions_on_battery" +Users: KToshiba + +What: /sys/devices/LNXSYSTM:00/LNXSYBUS:00/TOS{1900,620{0,7,8}}:00/sleep_functions_on_battery +Date: January 23, 2015 +KernelVersion: 4.0 +Contact: Azael Avalos +Description: This file controls the USB Sleep Functions under battery, and + set the level at which point they will be disabled, accepted + values can be: + * 0 -> Disabled + * 1-100 -> Battery level to disable sleep functions + Currently it prints two values, the first one indicates if the + feature is enabled or disabled, while the second one shows the + current battery level set. + Note that when the value is set to disabled, the sleep function + will only work when connected to power. +Users: KToshiba + +What: /sys/devices/LNXSYSTM:00/LNXSYBUS:00/TOS{1900,620{0,7,8}}:00/usb_rapid_charge +Date: January 23, 2015 +KernelVersion: 4.0 +Contact: Azael Avalos +Description: This file controls the USB Rapid Charge state, which can be: + * 0 -> Disabled + * 1 -> Enabled + Note that toggling this value requires a reboot for changes to + take effect. +Users: KToshiba + +What: /sys/devices/LNXSYSTM:00/LNXSYBUS:00/TOS{1900,620{0,7,8}}:00/usb_sleep_music +Date: January 23, 2015 +KernelVersion: 4.0 +Contact: Azael Avalos +Description: This file controls the Sleep & Music state, which values can be: + * 0 -> Disabled + * 1 -> Enabled + Note that this feature only works when connected to power, if + you want to use it under battery, see the entry named + "sleep_functions_on_battery" +Users: KToshiba + What: /sys/devices/LNXSYSTM:00/LNXSYBUS:00/TOS{1900,620{0,7,8}}:00/version -Date: February, 2015 -KernelVersion: 3.20 +Date: February 12, 2015 +KernelVersion: 4.0 Contact: Azael Avalos Description: This file shows the current version of the driver +Users: KToshiba What: /sys/devices/LNXSYSTM:00/LNXSYBUS:00/TOS{1900,620{0,7,8}}:00/fan -Date: February, 2015 -KernelVersion: 3.20 +Date: February 12, 2015 +KernelVersion: 4.0 Contact: Azael Avalos Description: This file controls the state of the internal fan, valid values are: @@ -83,8 +142,8 @@ Description: This file controls the state of the internal fan, valid * 1 -> ON What: /sys/devices/LNXSYSTM:00/LNXSYBUS:00/TOS{1900,620{0,7,8}}:00/kbd_function_keys -Date: February, 2015 -KernelVersion: 3.20 +Date: February 12, 2015 +KernelVersion: 4.0 Contact: Azael Avalos Description: This file controls the Special Functions (hotkeys) operation mode, valid values are: @@ -94,21 +153,29 @@ Description: This file controls the Special Functions (hotkeys) operation and the hotkeys are accessed via FN-F{1-12}. In the "Special Functions" mode, the F{1-12} keys trigger the hotkey and the F{1-12} keys are accessed via FN-F{1-12}. + Note that toggling this value requires a reboot for changes to + take effect. +Users: KToshiba What: /sys/devices/LNXSYSTM:00/LNXSYBUS:00/TOS{1900,620{0,7,8}}:00/panel_power_on -Date: February, 2015 -KernelVersion: 3.20 +Date: February 12, 2015 +KernelVersion: 4.0 Contact: Azael Avalos Description: This file controls whether the laptop should turn ON whenever the LID is opened, valid values are: * 0 -> Disabled * 1 -> Enabled + Note that toggling this value requires a reboot for changes to + take effect. +Users: KToshiba What: /sys/devices/LNXSYSTM:00/LNXSYBUS:00/TOS{1900,620{0,7,8}}:00/usb_three -Date: February, 2015 -KernelVersion: 3.20 +Date: February 12, 2015 +KernelVersion: 4.0 Contact: Azael Avalos -Description: This file controls whether the USB 3 functionality, valid - values are: +Description: This file controls the USB 3 functionality, valid values are: * 0 -> Disabled (Acts as a regular USB 2) * 1 -> Enabled (Full USB 3 functionality) + Note that toggling this value requires a reboot for changes to + take effect. +Users: KToshiba diff --git a/Documentation/ABI/testing/sysfs-platform-dell-laptop b/Documentation/ABI/testing/sysfs-platform-dell-laptop new file mode 100644 index 000000000000..8c6a0b8e1131 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-platform-dell-laptop @@ -0,0 +1,69 @@ +What: /sys/class/leds/dell::kbd_backlight/als_enabled +Date: December 2014 +KernelVersion: 3.19 +Contact: Gabriele Mazzotta , + Pali Rohár +Description: + This file allows to control the automatic keyboard + illumination mode on some systems that have an ambient + light sensor. Write 1 to this file to enable the auto + mode, 0 to disable it. + +What: /sys/class/leds/dell::kbd_backlight/als_setting +Date: December 2014 +KernelVersion: 3.19 +Contact: Gabriele Mazzotta , + Pali Rohár +Description: + This file allows to specifiy the on/off threshold value, + as reported by the ambient light sensor. + +What: /sys/class/leds/dell::kbd_backlight/start_triggers +Date: December 2014 +KernelVersion: 3.19 +Contact: Gabriele Mazzotta , + Pali Rohár +Description: + This file allows to control the input triggers that + turn on the keyboard backlight illumination that is + disabled because of inactivity. + Read the file to see the triggers available. The ones + enabled are preceded by '+', those disabled by '-'. + + To enable a trigger, write its name preceded by '+' to + this file. To disable a trigger, write its name preceded + by '-' instead. + + For example, to enable the keyboard as trigger run: + echo +keyboard > /sys/class/leds/dell::kbd_backlight/start_triggers + To disable it: + echo -keyboard > /sys/class/leds/dell::kbd_backlight/start_triggers + + Note that not all the available triggers can be configured. + +What: /sys/class/leds/dell::kbd_backlight/stop_timeout +Date: December 2014 +KernelVersion: 3.19 +Contact: Gabriele Mazzotta , + Pali Rohár +Description: + This file allows to specify the interval after which the + keyboard illumination is disabled because of inactivity. + The timeouts are expressed in seconds, minutes, hours and + days, for which the symbols are 's', 'm', 'h' and 'd' + respectively. + + To configure the timeout, write to this file a value along + with any the above units. If no unit is specified, the value + is assumed to be expressed in seconds. + + For example, to set the timeout to 10 minutes run: + echo 10m > /sys/class/leds/dell::kbd_backlight/stop_timeout + + Note that when this file is read, the returned value might be + expressed in a different unit than the one used when the timeout + was set. + + Also note that only some timeouts are supported and that + some systems might fall back to a specific timeout in case + an invalid timeout is written to this file. diff --git a/Documentation/DocBook/media/v4l/compat.xml b/Documentation/DocBook/media/v4l/compat.xml index 350dfb3d71ea..a0aef85d33c1 100644 --- a/Documentation/DocBook/media/v4l/compat.xml +++ b/Documentation/DocBook/media/v4l/compat.xml @@ -2491,7 +2491,7 @@ that used it. It was originally scheduled for removal in 2.6.35. Added V4L2_EVENT_CTRL_CH_RANGE control event - changes flag. See . + changes flag. See . diff --git a/Documentation/DocBook/media/v4l/media-ioc-enum-entities.xml b/Documentation/DocBook/media/v4l/media-ioc-enum-entities.xml index 116c301656e0..5872f8bbf774 100644 --- a/Documentation/DocBook/media/v4l/media-ioc-enum-entities.xml +++ b/Documentation/DocBook/media/v4l/media-ioc-enum-entities.xml @@ -143,86 +143,28 @@ struct - v4l + dev - Valid for V4L sub-devices and nodes only. + Valid for (sub-)devices that create a single device node. __u32 major - V4L device node major number. For V4L sub-devices with no - device node, set by the driver to 0. + Device node major number. __u32 minor - V4L device node minor number. For V4L sub-devices with no - device node, set by the driver to 0. - - - - struct - fb - - Valid for frame buffer nodes only. - - - - - __u32 - major - Frame buffer device node major number. - - - - - __u32 - minor - Frame buffer device node minor number. - - - - struct - alsa - - Valid for ALSA devices only. - - - - - __u32 - card - ALSA card number - - - - - __u32 - device - ALSA device number - - - - - __u32 - subdevice - ALSA sub-device number - - - - int - dvb - - DVB card number + Device node minor number. __u8 - raw[180] + raw[184] @@ -253,8 +195,24 @@ ALSA card - MEDIA_ENT_T_DEVNODE_DVB - DVB card + MEDIA_ENT_T_DEVNODE_DVB_FE + DVB frontend devnode + + + MEDIA_ENT_T_DEVNODE_DVB_DEMUX + DVB demux devnode + + + MEDIA_ENT_T_DEVNODE_DVB_DVR + DVB DVR devnode + + + MEDIA_ENT_T_DEVNODE_DVB_CA + DVB CAM devnode + + + MEDIA_ENT_T_DEVNODE_DVB_NET + DVB network devnode MEDIA_ENT_T_V4L2_SUBDEV @@ -282,6 +240,10 @@ it in some digital video standard, with appropriate embedded timing signals. + + MEDIA_ENT_T_V4L2_SUBDEV_TUNER + TV and/or radio tuner + diff --git a/Documentation/DocBook/media/v4l/pixfmt-packed-rgb.xml b/Documentation/DocBook/media/v4l/pixfmt-packed-rgb.xml index 6ab4f0f3db64..b60fb935b91b 100644 --- a/Documentation/DocBook/media/v4l/pixfmt-packed-rgb.xml +++ b/Documentation/DocBook/media/v4l/pixfmt-packed-rgb.xml @@ -303,45 +303,6 @@ for a pixel lie next to each other in memory. b1 b0 - - V4L2_PIX_FMT_BGR666 - 'BGRH' - - b5 - b4 - b3 - b2 - b1 - b0 - g5 - g4 - - g3 - g2 - g1 - g0 - r5 - r4 - r3 - r2 - - r1 - r0 - - - - - - - - - - - - - - - V4L2_PIX_FMT_BGR24 'BGR3' @@ -404,6 +365,46 @@ for a pixel lie next to each other in memory. b1 b0 + + V4L2_PIX_FMT_BGR666 + 'BGRH' + + b5 + b4 + b3 + b2 + b1 + b0 + g5 + g4 + + g3 + g2 + g1 + g0 + r5 + r4 + r3 + r2 + + r1 + r0 + - + - + - + - + - + - + + - + - + - + - + - + - + - + - + V4L2_PIX_FMT_ABGR32 'AR24' diff --git a/Documentation/DocBook/media/v4l/pixfmt-sgrbg8.xml b/Documentation/DocBook/media/v4l/pixfmt-sgrbg8.xml index 19727ab4c757..7803b8c41b45 100644 --- a/Documentation/DocBook/media/v4l/pixfmt-sgrbg8.xml +++ b/Documentation/DocBook/media/v4l/pixfmt-sgrbg8.xml @@ -38,10 +38,10 @@ columns and rows. start + 4: - R10 - B11 - R12 - B13 + B10 + G11 + B12 + G13 start + 8: @@ -52,10 +52,10 @@ columns and rows. start + 12: - R30 - B31 - R32 - B33 + B30 + G31 + B32 + G33 diff --git a/Documentation/DocBook/media/v4l/pixfmt-srggb10p.xml b/Documentation/DocBook/media/v4l/pixfmt-srggb10p.xml index 30aa63581fe3..a8cc102cde4f 100644 --- a/Documentation/DocBook/media/v4l/pixfmt-srggb10p.xml +++ b/Documentation/DocBook/media/v4l/pixfmt-srggb10p.xml @@ -38,7 +38,7 @@ Byte Order. Each cell is one byte. - + diff --git a/Documentation/DocBook/media/v4l/pixfmt-yuv420m.xml b/Documentation/DocBook/media/v4l/pixfmt-yuv420m.xml index 60308f1eefdf..e781cc61786c 100644 --- a/Documentation/DocBook/media/v4l/pixfmt-yuv420m.xml +++ b/Documentation/DocBook/media/v4l/pixfmt-yuv420m.xml @@ -29,12 +29,12 @@ and Cr planes have half as many pad bytes after their rows. In other words, two Cx rows (including padding) is exactly as long as one Y row (including padding). - V4L2_PIX_FMT_NV12M is intended to be + V4L2_PIX_FMT_YUV420M is intended to be used only in drivers and applications that support the multi-planar API, described in . - <constant>V4L2_PIX_FMT_YVU420M</constant> 4 × 4 + <title><constant>V4L2_PIX_FMT_YUV420M</constant> 4 × 4 pixel image diff --git a/Documentation/DocBook/media/v4l/pixfmt.xml b/Documentation/DocBook/media/v4l/pixfmt.xml index 5e0352c50324..fcde4e20205e 100644 --- a/Documentation/DocBook/media/v4l/pixfmt.xml +++ b/Documentation/DocBook/media/v4l/pixfmt.xml @@ -80,9 +80,9 @@ padding bytes after the last line of an image cross a system page boundary. Input devices may write padding bytes, the value is undefined. Output devices ignore the contents of padding bytes.When the image format is planar the -bytesperline value applies to the largest +bytesperline value applies to the first plane and is divided by the same factor as the -width field for any smaller planes. For +width field for the other planes. For example the Cb and Cr planes of a YUV 4:2:0 image have half as many padding bytes following each line as the Y plane. To avoid ambiguities drivers must return a bytesperline value @@ -182,14 +182,14 @@ see . - __u16 + __u32 bytesperline Distance in bytes between the leftmost pixels in two adjacent lines. See &v4l2-pix-format;. __u16 - reserved[7] + reserved[6] Reserved for future extensions. Should be zeroed by the application. @@ -483,8 +483,8 @@ is the Y'CbCr encoding identifier (&v4l2-ycbcr-encoding;) to specify non-standar Y'CbCr encodings and the third is the quantization identifier (&v4l2-quantization;) to specify non-standard quantization methods. Most of the time only the colorspace field of &v4l2-pix-format; or &v4l2-pix-format-mplane; needs to be filled in. Note -that the default R'G'B' quantization is always full range for all colorspaces, -so this won't be mentioned explicitly for each colorspace description. +that the default R'G'B' quantization is full range for all colorspaces except for +BT.2020 which uses limited range R'G'B' quantization. V4L2 Colorspaces @@ -598,7 +598,8 @@ so this won't be mentioned explicitly for each colorspace description. V4L2_QUANTIZATION_DEFAULT Use the default quantization encoding as defined by the colorspace. -This is always full range for R'G'B' and usually limited range for Y'CbCr. +This is always full range for R'G'B' (except for the BT.2020 colorspace) and usually +limited range for Y'CbCr. V4L2_QUANTIZATION_FULL_RANGE @@ -620,8 +621,8 @@ is mapped to [16…235]. Cb and Cr are mapped from [-0.5…0.5] to [16
Detailed Colorspace Descriptions -
- Colorspace SMPTE 170M (<constant>V4L2_COLORSPACE_SMPTE170M</constant>) +
+ Colorspace SMPTE 170M (<constant>V4L2_COLORSPACE_SMPTE170M</constant>) The standard defines the colorspace used by NTSC and PAL and by SDTV in general. The default Y'CbCr encoding is V4L2_YCBCR_ENC_601. The default Y'CbCr quantization is limited range. The chromaticities of the primary colors and @@ -666,8 +667,7 @@ as the SMPTE C set, so this colorspace is sometimes called SMPTE C as well. The transfer function defined for SMPTE 170M is the same as the -one defined in Rec. 709. Normally L is in the range [0…1], but for the extended -gamut xvYCC encoding values outside that range are allowed. +one defined in Rec. 709. L' = -1.099(-L)0.45 + 0.099 for L ≤ -0.018 L' = 4.5L for -0.018 < L < 0.018 @@ -702,29 +702,10 @@ defined in the standard and this colorspace is sometim though BT.601 does not mention any color primaries. The default quantization is limited range, but full range is possible although rarely seen. - The V4L2_YCBCR_ENC_601 encoding as described above is the -default for this colorspace, but it can be overridden with V4L2_YCBCR_ENC_709, -in which case the Rec. 709 Y'CbCr encoding is used. - - - The xvYCC 601 encoding (V4L2_YCBCR_ENC_XV601, ) is similar -to the BT.601 encoding, but it allows for R', G' and B' values that are outside the range -[0…1]. The resulting Y', Cb and Cr values are scaled and offset: - - Y' = (219 / 255) * (0.299R' + 0.587G' + 0.114B') + (16 / 255) - Cb = (224 / 255) * (-0.169R' - 0.331G' + 0.5B') - Cr = (224 / 255) * (0.5R' - 0.419G' - 0.081B') - - - - Y' is clamped to the range [0…1] and Cb and Cr are clamped -to the range [-0.5…0.5]. The non-standard xvYCC 709 encoding can also be used by selecting -V4L2_YCBCR_ENC_XV709. The xvYCC encodings always use full range -quantization.
-
- Colorspace Rec. 709 (<constant>V4L2_COLORSPACE_REC709</constant>) +
+ Colorspace Rec. 709 (<constant>V4L2_COLORSPACE_REC709</constant>) The standard defines the colorspace used by HDTV in general. The default Y'CbCr encoding is V4L2_YCBCR_ENC_709. The default Y'CbCr quantization is limited range. The chromaticities of the primary colors and the white reference are: @@ -803,26 +784,39 @@ rarely seen. The V4L2_YCBCR_ENC_709 encoding described above is the default for this colorspace, but it can be overridden with V4L2_YCBCR_ENC_601, in which case the BT.601 Y'CbCr encoding is used. + Two additional extended gamut Y'CbCr encodings are also possible with this colorspace: The xvYCC 709 encoding (V4L2_YCBCR_ENC_XV709, ) is similar to the Rec. 709 encoding, but it allows for R', G' and B' values that are outside the range [0…1]. The resulting Y', Cb and Cr values are scaled and offset: - Y' = (219 / 255) * (0.2126R' + 0.7152G' + 0.0722B') + (16 / 255) - Cb = (224 / 255) * (-0.1146R' - 0.3854G' + 0.5B') - Cr = (224 / 255) * (0.5R' - 0.4542G' - 0.0458B') + Y' = (219 / 256) * (0.2126R' + 0.7152G' + 0.0722B') + (16 / 256) + Cb = (224 / 256) * (-0.1146R' - 0.3854G' + 0.5B') + Cr = (224 / 256) * (0.5R' - 0.4542G' - 0.0458B') + + + + + + The xvYCC 601 encoding (V4L2_YCBCR_ENC_XV601, ) is similar +to the BT.601 encoding, but it allows for R', G' and B' values that are outside the range +[0…1]. The resulting Y', Cb and Cr values are scaled and offset: + + Y' = (219 / 256) * (0.299R' + 0.587G' + 0.114B') + (16 / 256) + Cb = (224 / 256) * (-0.169R' - 0.331G' + 0.5B') + Cr = (224 / 256) * (0.5R' - 0.419G' - 0.081B') Y' is clamped to the range [0…1] and Cb and Cr are clamped -to the range [-0.5…0.5]. The non-standard xvYCC 601 encoding can also be used by -selecting V4L2_YCBCR_ENC_XV601. The xvYCC encodings always use full -range quantization. +to the range [-0.5…0.5]. The non-standard xvYCC 709 or xvYCC 601 encodings can be used by +selecting V4L2_YCBCR_ENC_XV709 or V4L2_YCBCR_ENC_XV601. +The xvYCC encodings always use full range quantization.
-
- Colorspace sRGB (<constant>V4L2_COLORSPACE_SRGB</constant>) +
+ Colorspace sRGB (<constant>V4L2_COLORSPACE_SRGB</constant>) The standard defines the colorspace used by most webcams and computer graphics. The default Y'CbCr encoding is V4L2_YCBCR_ENC_SYCC. The default Y'CbCr quantization is full range. The chromaticities of the primary colors and the white reference are: @@ -898,8 +892,8 @@ encoding, it is not. The V4L2_YCBCR_ENC_XV601 scales and of values before quantization, but this encoding does not do that.
-
- Colorspace Adobe RGB (<constant>V4L2_COLORSPACE_ADOBERGB</constant>) +
+ Colorspace Adobe RGB (<constant>V4L2_COLORSPACE_ADOBERGB</constant>) The standard defines the colorspace used by computer graphics that use the AdobeRGB colorspace. This is also known as the standard. The default Y'CbCr encoding is V4L2_YCBCR_ENC_601. The default Y'CbCr @@ -970,12 +964,12 @@ clamped to the range [-0.5…0.5]. This transform is identical to one defin SMPTE 170M/BT.601. The Y'CbCr quantization is limited range.
-
- Colorspace BT.2020 (<constant>V4L2_COLORSPACE_BT2020</constant>) +
+ Colorspace BT.2020 (<constant>V4L2_COLORSPACE_BT2020</constant>) The standard defines the colorspace used by Ultra-high definition television (UHDTV). The default Y'CbCr encoding is V4L2_YCBCR_ENC_BT2020. -The default Y'CbCr quantization is limited range. The chromaticities of the primary colors and -the white reference are: +The default R'G'B' quantization is limited range (!), and so is the default Y'CbCr quantization. +The chromaticities of the primary colors and the white reference are:
BT.2020 Chromaticities @@ -1032,7 +1026,7 @@ the white reference are: The luminance (Y') and color difference (Cb and Cr) are obtained with the following V4L2_YCBCR_ENC_BT2020 encoding: - Y' = 0.2627R' + 0.6789G' + 0.0593B' + Y' = 0.2627R' + 0.6780G' + 0.0593B' Cb = -0.1396R' - 0.3604G' + 0.5B' Cr = 0.5R' - 0.4598G' - 0.0402B' @@ -1046,7 +1040,7 @@ clamped to the range [-0.5…0.5]. The Y'CbCr quantization is limited range Luma: - Yc' = (0.2627R + 0.6789G + 0.0593B)' + Yc' = (0.2627R + 0.6780G + 0.0593B)' @@ -1054,7 +1048,7 @@ clamped to the range [-0.5…0.5]. The Y'CbCr quantization is limited range B' - Yc' ≤ 0: - Cbc = (B' - Y') / 1.9404 + Cbc = (B' - Yc') / 1.9404 @@ -1062,7 +1056,7 @@ clamped to the range [-0.5…0.5]. The Y'CbCr quantization is limited range B' - Yc' > 0: - Cbc = (B' - Y') / 1.5816 + Cbc = (B' - Yc') / 1.5816 @@ -1086,8 +1080,8 @@ clamped to the range [-0.5…0.5]. The Y'CbCr quantization is limited range clamped to the range [-0.5…0.5]. The Yc'CbcCrc quantization is limited range. -
- Colorspace SMPTE 240M (<constant>V4L2_COLORSPACE_SMPTE240M</constant>) +
+ Colorspace SMPTE 240M (<constant>V4L2_COLORSPACE_SMPTE240M</constant>) The standard was an interim standard used during the early days of HDTV (1988-1998). It has been superseded by Rec. 709. The default Y'CbCr encoding is V4L2_YCBCR_ENC_SMPTE240M. The default Y'CbCr quantization is limited range. The chromaticities of the primary colors and the @@ -1159,8 +1153,8 @@ following V4L2_YCBCR_ENC_SMPTE240M encoding: clamped to the range [-0.5…0.5]. The Y'CbCr quantization is limited range.
-
- Colorspace NTSC 1953 (<constant>V4L2_COLORSPACE_470_SYSTEM_M</constant>) +
+ Colorspace NTSC 1953 (<constant>V4L2_COLORSPACE_470_SYSTEM_M</constant>) This standard defines the colorspace used by NTSC in 1953. In practice this colorspace is obsolete and SMPTE 170M should be used instead. The default Y'CbCr encoding is V4L2_YCBCR_ENC_601. The default Y'CbCr quantization is limited range. @@ -1237,8 +1231,8 @@ clamped to the range [-0.5…0.5]. The Y'CbCr quantization is limited range This transform is identical to one defined in SMPTE 170M/BT.601.
-
- Colorspace EBU Tech. 3213 (<constant>V4L2_COLORSPACE_470_SYSTEM_BG</constant>) +
+ Colorspace EBU Tech. 3213 (<constant>V4L2_COLORSPACE_470_SYSTEM_BG</constant>) The standard defines the colorspace used by PAL/SECAM in 1975. In practice this colorspace is obsolete and SMPTE 170M should be used instead. The default Y'CbCr encoding is V4L2_YCBCR_ENC_601. The default Y'CbCr quantization is limited range. @@ -1311,8 +1305,8 @@ clamped to the range [-0.5…0.5]. The Y'CbCr quantization is limited range This transform is identical to one defined in SMPTE 170M/BT.601.
-
- Colorspace JPEG (<constant>V4L2_COLORSPACE_JPEG</constant>) +
+ Colorspace JPEG (<constant>V4L2_COLORSPACE_JPEG</constant>) This colorspace defines the colorspace used by most (Motion-)JPEG formats. The chromaticities of the primary colors and the white reference are identical to sRGB. The Y'CbCr encoding is V4L2_YCBCR_ENC_601 with full range quantization where diff --git a/Documentation/DocBook/media/v4l/subdev-formats.xml b/Documentation/DocBook/media/v4l/subdev-formats.xml index 553a38024745..2588ad781242 100644 --- a/Documentation/DocBook/media/v4l/subdev-formats.xml +++ b/Documentation/DocBook/media/v4l/subdev-formats.xml @@ -482,6 +482,36 @@ see . b1 b0 + + MEDIA_BUS_FMT_RBG888_1X24 + 0x100e + + &dash-ent-8; + r7 + r6 + r5 + r4 + r3 + r2 + r1 + r0 + b7 + b6 + b5 + b4 + b3 + b2 + b1 + b0 + g7 + g6 + g5 + g4 + g3 + g2 + g1 + g0 + MEDIA_BUS_FMT_RGB666_1X24_CPADHI 0x1015 @@ -711,6 +741,43 @@ see . b1 b0 + + MEDIA_BUS_FMT_RGB888_1X32_PADHI + 0x100f + + 0 + 0 + 0 + 0 + 0 + 0 + 0 + 0 + r7 + r6 + r5 + r4 + r3 + r2 + r1 + r0 + g7 + g6 + g5 + g4 + g3 + g2 + g1 + g0 + b7 + b6 + b5 + b4 + b3 + b2 + b1 + b0 +
@@ -2575,6 +2642,294 @@ see . y1 y0 + + MEDIA_BUS_FMT_UYVY12_2X12 + 0x201c + + &dash-ent-20; + u11 + u10 + u9 + u8 + u7 + u6 + u5 + u4 + u3 + u2 + u1 + u0 + + + + + + &dash-ent-20; + y11 + y10 + y9 + y8 + y7 + y6 + y5 + y4 + y3 + y2 + y1 + y0 + + + + + + &dash-ent-20; + v11 + v10 + v9 + v8 + v7 + v6 + v5 + v4 + v3 + v2 + v1 + v0 + + + + + + &dash-ent-20; + y11 + y10 + y9 + y8 + y7 + y6 + y5 + y4 + y3 + y2 + y1 + y0 + + + MEDIA_BUS_FMT_VYUY12_2X12 + 0x201d + + &dash-ent-20; + v11 + v10 + v9 + v8 + v7 + v6 + v5 + v4 + v3 + v2 + v1 + v0 + + + + + + &dash-ent-20; + y11 + y10 + y9 + y8 + y7 + y6 + y5 + y4 + y3 + y2 + y1 + y0 + + + + + + &dash-ent-20; + u11 + u10 + u9 + u8 + u7 + u6 + u5 + u4 + u3 + u2 + u1 + u0 + + + + + + &dash-ent-20; + y11 + y10 + y9 + y8 + y7 + y6 + y5 + y4 + y3 + y2 + y1 + y0 + + + MEDIA_BUS_FMT_YUYV12_2X12 + 0x201e + + &dash-ent-20; + y11 + y10 + y9 + y8 + y7 + y6 + y5 + y4 + y3 + y2 + y1 + y0 + + + + + + &dash-ent-20; + u11 + u10 + u9 + u8 + u7 + u6 + u5 + u4 + u3 + u2 + u1 + u0 + + + + + + &dash-ent-20; + y11 + y10 + y9 + y8 + y7 + y6 + y5 + y4 + y3 + y2 + y1 + y0 + + + + + + &dash-ent-20; + v11 + v10 + v9 + v8 + v7 + v6 + v5 + v4 + v3 + v2 + v1 + v0 + + + MEDIA_BUS_FMT_YVYU12_2X12 + 0x201f + + &dash-ent-20; + y11 + y10 + y9 + y8 + y7 + y6 + y5 + y4 + y3 + y2 + y1 + y0 + + + + + + &dash-ent-20; + v11 + v10 + v9 + v8 + v7 + v6 + v5 + v4 + v3 + v2 + v1 + v0 + + + + + + &dash-ent-20; + y11 + y10 + y9 + y8 + y7 + y6 + y5 + y4 + y3 + y2 + y1 + y0 + + + + + + &dash-ent-20; + u11 + u10 + u9 + u8 + u7 + u6 + u5 + u4 + u3 + u2 + u1 + u0 + MEDIA_BUS_FMT_UYVY8_1X16 0x200f @@ -3047,6 +3402,36 @@ see . u1 u0 + + MEDIA_BUS_FMT_VUY8_1X24 + 0x201a + + &dash-ent-8; + v7 + v6 + v5 + v4 + v3 + v2 + v1 + v0 + u7 + u6 + u5 + u4 + u3 + u2 + u1 + u0 + y7 + y6 + y5 + y4 + y3 + y2 + y1 + y0 + MEDIA_BUS_FMT_YUV8_1X24 0x2025 @@ -3084,368 +3469,6 @@ see . v1 v0 - - MEDIA_BUS_FMT_YUV10_1X30 - 0x2016 - - - - - - y9 - y8 - y7 - y6 - y5 - y4 - y3 - y2 - y1 - y0 - u9 - u8 - u7 - u6 - u5 - u4 - u3 - u2 - u1 - u0 - v9 - v8 - v7 - v6 - v5 - v4 - v3 - v2 - v1 - v0 - - - MEDIA_BUS_FMT_AYUV8_1X32 - 0x2017 - - a7 - a6 - a5 - a4 - a3 - a2 - a1 - a0 - y7 - y6 - y5 - y4 - y3 - y2 - y1 - y0 - u7 - u6 - u5 - u4 - u3 - u2 - u1 - u0 - v7 - v6 - v5 - v4 - v3 - v2 - v1 - v0 - - - MEDIA_BUS_FMT_UYVY12_2X12 - 0x201c - - &dash-ent-20; - u11 - u10 - u9 - u8 - u7 - u6 - u5 - u4 - u3 - u2 - u1 - u0 - - - - - - &dash-ent-20; - y11 - y10 - y9 - y8 - y7 - y6 - y5 - y4 - y3 - y2 - y1 - y0 - - - - - - &dash-ent-20; - v11 - v10 - v9 - v8 - v7 - v6 - v5 - v4 - v3 - v2 - v1 - v0 - - - - - - &dash-ent-20; - y11 - y10 - y9 - y8 - y7 - y6 - y5 - y4 - y3 - y2 - y1 - y0 - - - MEDIA_BUS_FMT_VYUY12_2X12 - 0x201d - - &dash-ent-20; - v11 - v10 - v9 - v8 - v7 - v6 - v5 - v4 - v3 - v2 - v1 - v0 - - - - - - &dash-ent-20; - y11 - y10 - y9 - y8 - y7 - y6 - y5 - y4 - y3 - y2 - y1 - y0 - - - - - - &dash-ent-20; - u11 - u10 - u9 - u8 - u7 - u6 - u5 - u4 - u3 - u2 - u1 - u0 - - - - - - &dash-ent-20; - y11 - y10 - y9 - y8 - y7 - y6 - y5 - y4 - y3 - y2 - y1 - y0 - - - MEDIA_BUS_FMT_YUYV12_2X12 - 0x201e - - &dash-ent-20; - y11 - y10 - y9 - y8 - y7 - y6 - y5 - y4 - y3 - y2 - y1 - y0 - - - - - - &dash-ent-20; - u11 - u10 - u9 - u8 - u7 - u6 - u5 - u4 - u3 - u2 - u1 - u0 - - - - - - &dash-ent-20; - y11 - y10 - y9 - y8 - y7 - y6 - y5 - y4 - y3 - y2 - y1 - y0 - - - - - - &dash-ent-20; - v11 - v10 - v9 - v8 - v7 - v6 - v5 - v4 - v3 - v2 - v1 - v0 - - - MEDIA_BUS_FMT_YVYU12_2X12 - 0x201f - - &dash-ent-20; - y11 - y10 - y9 - y8 - y7 - y6 - y5 - y4 - y3 - y2 - y1 - y0 - - - - - - &dash-ent-20; - v11 - v10 - v9 - v8 - v7 - v6 - v5 - v4 - v3 - v2 - v1 - v0 - - - - - - &dash-ent-20; - y11 - y10 - y9 - y8 - y7 - y6 - y5 - y4 - y3 - y2 - y1 - y0 - - - - - - &dash-ent-20; - u11 - u10 - u9 - u8 - u7 - u6 - u5 - u4 - u3 - u2 - u1 - u0 - MEDIA_BUS_FMT_UYVY12_1X24 0x2020 @@ -3686,6 +3709,80 @@ see . u1 u0 + + MEDIA_BUS_FMT_YUV10_1X30 + 0x2016 + + - + - + y9 + y8 + y7 + y6 + y5 + y4 + y3 + y2 + y1 + y0 + u9 + u8 + u7 + u6 + u5 + u4 + u3 + u2 + u1 + u0 + v9 + v8 + v7 + v6 + v5 + v4 + v3 + v2 + v1 + v0 + + + MEDIA_BUS_FMT_AYUV8_1X32 + 0x2017 + + a7 + a6 + a5 + a4 + a3 + a2 + a1 + a0 + y7 + y6 + y5 + y4 + y3 + y2 + y1 + y0 + u7 + u6 + u5 + u4 + u3 + u2 + u1 + u0 + v7 + v6 + v5 + v4 + v3 + v2 + v1 + v0 + diff --git a/Documentation/DocBook/media/v4l/v4l2.xml b/Documentation/DocBook/media/v4l/v4l2.xml index ac0f8d9d2a49..e98caa1c39bd 100644 --- a/Documentation/DocBook/media/v4l/v4l2.xml +++ b/Documentation/DocBook/media/v4l/v4l2.xml @@ -136,6 +136,7 @@ Remote Controller chapter. 2012 2013 2014 + 2015 Bill Dirks, Michael H. Schimek, Hans Verkuil, Martin Rubli, Andy Walls, Muralidharan Karicheri, Mauro Carvalho Chehab, Pawel Osciak @@ -151,6 +152,14 @@ structs, ioctls) must be noted in more detail in the history chapter (compat.xml), along with the possible impact on existing drivers and applications. --> + + 3.21 + 2015-02-13 + mcc + Fix documentation for media controller device nodes and add support for DVB device nodes. +Add support for Tuner sub-device. + + 3.19 2014-12-05 diff --git a/Documentation/DocBook/media/v4l/vidioc-cropcap.xml b/Documentation/DocBook/media/v4l/vidioc-cropcap.xml index 1f5ed64cd75a..50cb940cbe5c 100644 --- a/Documentation/DocBook/media/v4l/vidioc-cropcap.xml +++ b/Documentation/DocBook/media/v4l/vidioc-cropcap.xml @@ -59,6 +59,11 @@ constant except when switching the video standard. Remember this switch can occur implicit when switching the video input or output. +Do not use the multiplanar buffer types. Use V4L2_BUF_TYPE_VIDEO_CAPTURE +instead of V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE +and use V4L2_BUF_TYPE_VIDEO_OUTPUT instead of +V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE. + This ioctl must be implemented for video capture or output devices that support cropping and/or scaling and/or have non-square pixels, and for overlay devices. @@ -73,9 +78,7 @@ support cropping and/or scaling and/or have non-square pixels, and for overlay d Type of the data stream, set by the application. Only these types are valid here: V4L2_BUF_TYPE_VIDEO_CAPTURE, -V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE, -V4L2_BUF_TYPE_VIDEO_OUTPUT, -V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE and +V4L2_BUF_TYPE_VIDEO_OUTPUT and V4L2_BUF_TYPE_VIDEO_OVERLAY. See . diff --git a/Documentation/DocBook/media/v4l/vidioc-dqevent.xml b/Documentation/DocBook/media/v4l/vidioc-dqevent.xml index b036f8963353..50ccd33948c1 100644 --- a/Documentation/DocBook/media/v4l/vidioc-dqevent.xml +++ b/Documentation/DocBook/media/v4l/vidioc-dqevent.xml @@ -64,7 +64,7 @@ __u32 type - Type of the event. + Type of the event, see . union @@ -154,6 +154,113 @@ + + Event Types + + &cs-def; + + + V4L2_EVENT_ALL + 0 + All events. V4L2_EVENT_ALL is valid only for + VIDIOC_UNSUBSCRIBE_EVENT for unsubscribing all events at once. + + + + V4L2_EVENT_VSYNC + 1 + This event is triggered on the vertical sync. + This event has a &v4l2-event-vsync; associated with it. + + + + V4L2_EVENT_EOS + 2 + This event is triggered when the end of a stream is reached. + This is typically used with MPEG decoders to report to the application + when the last of the MPEG stream has been decoded. + + + + V4L2_EVENT_CTRL + 3 + This event requires that the id + matches the control ID from which you want to receive events. + This event is triggered if the control's value changes, if a + button control is pressed or if the control's flags change. + This event has a &v4l2-event-ctrl; associated with it. This struct + contains much of the same information as &v4l2-queryctrl; and + &v4l2-control;. + + If the event is generated due to a call to &VIDIOC-S-CTRL; or + &VIDIOC-S-EXT-CTRLS;, then the event will not be sent to + the file handle that called the ioctl function. This prevents + nasty feedback loops. If you do want to get the + event, then set the V4L2_EVENT_SUB_FL_ALLOW_FEEDBACK + flag. + + + This event type will ensure that no information is lost when + more events are raised than there is room internally. In that + case the &v4l2-event-ctrl; of the second-oldest event is kept, + but the changes field of the + second-oldest event is ORed with the changes + field of the oldest event. + + + + V4L2_EVENT_FRAME_SYNC + 4 + + Triggered immediately when the reception of a + frame has begun. This event has a + &v4l2-event-frame-sync; associated with it. + + If the hardware needs to be stopped in the case of a + buffer underrun it might not be able to generate this event. + In such cases the frame_sequence + field in &v4l2-event-frame-sync; will not be incremented. This + causes two consecutive frame sequence numbers to have n times + frame interval in between them. + + + + V4L2_EVENT_SOURCE_CHANGE + 5 + + This event is triggered when a source parameter change is + detected during runtime by the video device. It can be a + runtime resolution change triggered by a video decoder or the + format change happening on an input connector. + This event requires that the id + matches the input index (when used with a video device node) + or the pad index (when used with a subdevice node) from which + you want to receive events. + + This event has a &v4l2-event-src-change; associated + with it. The changes bitfield denotes + what has changed for the subscribed pad. If multiple events + occurred before application could dequeue them, then the changes + will have the ORed value of all the events generated. + + + + V4L2_EVENT_MOTION_DET + 6 + + Triggered whenever the motion detection state for one or more of the regions + changes. This event has a &v4l2-event-motion-det; associated with it. + + + + V4L2_EVENT_PRIVATE_START + 0x08000000 + Base event number for driver-private events. + + + +
+ struct <structname>v4l2_event_vsync</structname> @@ -177,7 +284,7 @@ __u32 changes - A bitmask that tells what has changed. See . + A bitmask that tells what has changed. See . __u32 @@ -309,8 +416,8 @@
- - Changes +
+ Control Changes &cs-def; @@ -318,9 +425,9 @@ V4L2_EVENT_CTRL_CH_VALUE0x0001This control event was triggered because the value of the control - changed. Special case: if a button control is pressed, then this - event is sent as well, even though there is not explicit value - associated with a button control. + changed. Special cases: Volatile controls do no generate this event; + If a control has the V4L2_CTRL_FLAG_EXECUTE_ON_WRITE + flag set, then this event is sent as well, regardless its value. V4L2_EVENT_CTRL_CH_FLAGS diff --git a/Documentation/DocBook/media/v4l/vidioc-g-crop.xml b/Documentation/DocBook/media/v4l/vidioc-g-crop.xml index 75c6a93de3c1..e6c4efb9e8b4 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-crop.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-crop.xml @@ -70,6 +70,11 @@ structure or returns the &EINVAL; if cropping is not supported. VIDIOC_S_CROP ioctl with a pointer to this structure. +Do not use the multiplanar buffer types. Use V4L2_BUF_TYPE_VIDEO_CAPTURE +instead of V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE +and use V4L2_BUF_TYPE_VIDEO_OUTPUT instead of +V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE. + The driver first adjusts the requested dimensions against hardware limits, &ie; the bounds given by the capture/output window, and it rounds to the closest possible values of horizontal and diff --git a/Documentation/DocBook/media/v4l/vidioc-g-dv-timings.xml b/Documentation/DocBook/media/v4l/vidioc-g-dv-timings.xml index c4336577ff06..764b635ed4cf 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-dv-timings.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-dv-timings.xml @@ -318,10 +318,20 @@ can't generate such frequencies, then the flag will also be cleared. V4L2_DV_FL_HALF_LINE - Specific to interlaced formats: if set, then field 1 (aka the odd field) -is really one half-line longer and field 2 (aka the even field) is really one half-line -shorter, so each field has exactly the same number of half-lines. Whether half-lines can be -detected or used depends on the hardware. + Specific to interlaced formats: if set, then the vertical frontporch +of field 1 (aka the odd field) is really one half-line longer and the vertical backporch +of field 2 (aka the even field) is really one half-line shorter, so each field has exactly +the same number of half-lines. Whether half-lines can be detected or used depends on +the hardware. + + + + V4L2_DV_FL_IS_CE_VIDEO + If set, then this is a Consumer Electronics (CE) video format. +Such formats differ from other formats (commonly called IT formats) in that if +R'G'B' encoding is used then by default the R'G'B' values use limited range +(i.e. 16-235) as opposed to full range (i.e. 0-255). All formats defined in CEA-861 +except for the 640x480p59.94 format are CE formats. diff --git a/Documentation/DocBook/media/v4l/vidioc-g-fbuf.xml b/Documentation/DocBook/media/v4l/vidioc-g-fbuf.xml index 20460730b02c..77607cc19688 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-fbuf.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-fbuf.xml @@ -240,9 +240,9 @@ where padding bytes after the last line of an image cross a system page boundary. Capture devices may write padding bytes, the value is undefined. Output devices ignore the contents of padding bytes.When the image format is planar the -bytesperline value applies to the largest +bytesperline value applies to the first plane and is divided by the same factor as the -width field for any smaller planes. For +width field for the other planes. For example the Cb and Cr planes of a YUV 4:2:0 image have half as many padding bytes following each line as the Y plane. To avoid ambiguities drivers must return a bytesperline value diff --git a/Documentation/DocBook/media/v4l/vidioc-g-selection.xml b/Documentation/DocBook/media/v4l/vidioc-g-selection.xml index 9c04ac8661b1..0bb5c060db27 100644 --- a/Documentation/DocBook/media/v4l/vidioc-g-selection.xml +++ b/Documentation/DocBook/media/v4l/vidioc-g-selection.xml @@ -60,8 +60,8 @@ To query the cropping (composing) rectangle set &v4l2-selection; type field to the respective buffer type. -Do not use multiplanar buffers. Use V4L2_BUF_TYPE_VIDEO_CAPTURE -instead of V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE. Use +Do not use the multiplanar buffer types. Use V4L2_BUF_TYPE_VIDEO_CAPTURE +instead of V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE and use V4L2_BUF_TYPE_VIDEO_OUTPUT instead of V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE. The next step is setting the value of &v4l2-selection; target field diff --git a/Documentation/DocBook/media/v4l/vidioc-querycap.xml b/Documentation/DocBook/media/v4l/vidioc-querycap.xml index d0c5e604f014..20fda75a012d 100644 --- a/Documentation/DocBook/media/v4l/vidioc-querycap.xml +++ b/Documentation/DocBook/media/v4l/vidioc-querycap.xml @@ -102,10 +102,10 @@ The bus_info must start with "PCI:" for PCI boards, "PCIe:" for PCI Express boar __u32 version Version number of the driver. -Starting on kernel 3.1, the version reported is provided per -V4L2 subsystem, following the same Kernel numberation scheme. However, it -should not always return the same version as the kernel, if, for example, -an stable or distribution-modified kernel uses the V4L2 stack from a +Starting with kernel 3.1, the version reported is provided by the +V4L2 subsystem following the kernel numbering scheme. However, it +may not always return the same version as the kernel if, for example, +a stable or distribution-modified kernel uses the V4L2 stack from a newer kernel. The version number is formatted using the KERNEL_VERSION() macro: diff --git a/Documentation/DocBook/media/v4l/vidioc-queryctrl.xml b/Documentation/DocBook/media/v4l/vidioc-queryctrl.xml index 2bd98fd7a4e5..dc83ad70f8dc 100644 --- a/Documentation/DocBook/media/v4l/vidioc-queryctrl.xml +++ b/Documentation/DocBook/media/v4l/vidioc-queryctrl.xml @@ -600,7 +600,9 @@ writing a value will cause the device to carry out a given action changes continuously. A typical example would be the current gain value if the device is in auto-gain mode. In such a case the hardware calculates the gain value based on the lighting conditions which can change over time. Note that setting a new value for -a volatile control will have no effect. The new value will just be ignored. +a volatile control will have no effect and no V4L2_EVENT_CTRL_CH_VALUE +will be sent, unless the V4L2_CTRL_FLAG_EXECUTE_ON_WRITE flag +(see below) is also set. Otherwise the new value will just be ignored. V4L2_CTRL_FLAG_HAS_PAYLOAD @@ -610,6 +612,14 @@ using one of the pointer fields of &v4l2-ext-control;. This flag is set for cont that are an array, string, or have a compound type. In all cases you have to set a pointer to memory containing the payload of the control. + + V4L2_CTRL_FLAG_EXECUTE_ON_WRITE + 0x0200 + The value provided to the control will be propagated to the driver +even if remains constant. This is required when the control represents an action +on the hardware. For example: clearing an error flag or triggering the flash. All the +controls of the type V4L2_CTRL_TYPE_BUTTON have this flag set. +
diff --git a/Documentation/DocBook/media/v4l/vidioc-subdev-enum-frame-interval.xml b/Documentation/DocBook/media/v4l/vidioc-subdev-enum-frame-interval.xml index 2f8f4f0a0235..cff59f5cbf04 100644 --- a/Documentation/DocBook/media/v4l/vidioc-subdev-enum-frame-interval.xml +++ b/Documentation/DocBook/media/v4l/vidioc-subdev-enum-frame-interval.xml @@ -67,9 +67,9 @@ To enumerate frame intervals applications initialize the index, pad, - code, width and - height fields of - &v4l2-subdev-frame-interval-enum; and call the + which, code, + width and height + fields of &v4l2-subdev-frame-interval-enum; and call the VIDIOC_SUBDEV_ENUM_FRAME_INTERVAL ioctl with a pointer to this structure. Drivers fill the rest of the structure or return an &EINVAL; if one of the input fields is invalid. All frame intervals are @@ -123,7 +123,12 @@ __u32 - reserved[9] + which + Frame intervals to be enumerated, from &v4l2-subdev-format-whence;. + + + __u32 + reserved[8] Reserved for future extensions. Applications and drivers must set the array to zero. diff --git a/Documentation/DocBook/media/v4l/vidioc-subdev-enum-frame-size.xml b/Documentation/DocBook/media/v4l/vidioc-subdev-enum-frame-size.xml index 79ce42b7c60c..abd545ede67a 100644 --- a/Documentation/DocBook/media/v4l/vidioc-subdev-enum-frame-size.xml +++ b/Documentation/DocBook/media/v4l/vidioc-subdev-enum-frame-size.xml @@ -61,9 +61,9 @@ ioctl. To enumerate frame sizes applications initialize the - pad, code and - index fields of the - &v4l2-subdev-mbus-code-enum; and call the + pad, which , + code and index + fields of the &v4l2-subdev-mbus-code-enum; and call the VIDIOC_SUBDEV_ENUM_FRAME_SIZE ioctl with a pointer to the structure. Drivers fill the minimum and maximum frame sizes or return an &EINVAL; if one of the input parameters is invalid. @@ -127,7 +127,12 @@ __u32 - reserved[9] + which + Frame sizes to be enumerated, from &v4l2-subdev-format-whence;. + + + __u32 + reserved[8] Reserved for future extensions. Applications and drivers must set the array to zero. diff --git a/Documentation/DocBook/media/v4l/vidioc-subdev-enum-mbus-code.xml b/Documentation/DocBook/media/v4l/vidioc-subdev-enum-mbus-code.xml index a6b3432449f6..0bcb278fd062 100644 --- a/Documentation/DocBook/media/v4l/vidioc-subdev-enum-mbus-code.xml +++ b/Documentation/DocBook/media/v4l/vidioc-subdev-enum-mbus-code.xml @@ -56,8 +56,8 @@ To enumerate media bus formats available at a given sub-device pad - applications initialize the pad and - index fields of &v4l2-subdev-mbus-code-enum; and + applications initialize the pad, which + and index fields of &v4l2-subdev-mbus-code-enum; and call the VIDIOC_SUBDEV_ENUM_MBUS_CODE ioctl with a pointer to this structure. Drivers fill the rest of the structure or return an &EINVAL; if either the pad or @@ -93,7 +93,12 @@ __u32 - reserved[9] + which + Media bus format codes to be enumerated, from &v4l2-subdev-format-whence;. + + + __u32 + reserved[8] Reserved for future extensions. Applications and drivers must set the array to zero. diff --git a/Documentation/DocBook/media/v4l/vidioc-subscribe-event.xml b/Documentation/DocBook/media/v4l/vidioc-subscribe-event.xml index d7c9365ecdbe..d0332f610929 100644 --- a/Documentation/DocBook/media/v4l/vidioc-subscribe-event.xml +++ b/Documentation/DocBook/media/v4l/vidioc-subscribe-event.xml @@ -60,7 +60,9 @@ __u32 type - Type of the event. + Type of the event, see . Note that +V4L2_EVENT_ALL can be used with VIDIOC_UNSUBSCRIBE_EVENT +for unsubscribing all events at once. __u32 @@ -84,113 +86,6 @@ - - Event Types - - &cs-def; - - - V4L2_EVENT_ALL - 0 - All events. V4L2_EVENT_ALL is valid only for - VIDIOC_UNSUBSCRIBE_EVENT for unsubscribing all events at once. - - - - V4L2_EVENT_VSYNC - 1 - This event is triggered on the vertical sync. - This event has a &v4l2-event-vsync; associated with it. - - - - V4L2_EVENT_EOS - 2 - This event is triggered when the end of a stream is reached. - This is typically used with MPEG decoders to report to the application - when the last of the MPEG stream has been decoded. - - - - V4L2_EVENT_CTRL - 3 - This event requires that the id - matches the control ID from which you want to receive events. - This event is triggered if the control's value changes, if a - button control is pressed or if the control's flags change. - This event has a &v4l2-event-ctrl; associated with it. This struct - contains much of the same information as &v4l2-queryctrl; and - &v4l2-control;. - - If the event is generated due to a call to &VIDIOC-S-CTRL; or - &VIDIOC-S-EXT-CTRLS;, then the event will not be sent to - the file handle that called the ioctl function. This prevents - nasty feedback loops. If you do want to get the - event, then set the V4L2_EVENT_SUB_FL_ALLOW_FEEDBACK - flag. - - - This event type will ensure that no information is lost when - more events are raised than there is room internally. In that - case the &v4l2-event-ctrl; of the second-oldest event is kept, - but the changes field of the - second-oldest event is ORed with the changes - field of the oldest event. - - - - V4L2_EVENT_FRAME_SYNC - 4 - - Triggered immediately when the reception of a - frame has begun. This event has a - &v4l2-event-frame-sync; associated with it. - - If the hardware needs to be stopped in the case of a - buffer underrun it might not be able to generate this event. - In such cases the frame_sequence - field in &v4l2-event-frame-sync; will not be incremented. This - causes two consecutive frame sequence numbers to have n times - frame interval in between them. - - - - V4L2_EVENT_SOURCE_CHANGE - 5 - - This event is triggered when a source parameter change is - detected during runtime by the video device. It can be a - runtime resolution change triggered by a video decoder or the - format change happening on an input connector. - This event requires that the id - matches the input index (when used with a video device node) - or the pad index (when used with a subdevice node) from which - you want to receive events. - - This event has a &v4l2-event-src-change; associated - with it. The changes bitfield denotes - what has changed for the subscribed pad. If multiple events - occurred before application could dequeue them, then the changes - will have the ORed value of all the events generated. - - - - V4L2_EVENT_MOTION_DET - 6 - - Triggered whenever the motion detection state for one or more of the regions - changes. This event has a &v4l2-event-motion-det; associated with it. - - - - V4L2_EVENT_PRIVATE_START - 0x08000000 - Base event number for driver-private events. - - - -
- Event Flags diff --git a/Documentation/IPMI.txt b/Documentation/IPMI.txt index 653d5d739d7f..31d1d658827f 100644 --- a/Documentation/IPMI.txt +++ b/Documentation/IPMI.txt @@ -505,7 +505,10 @@ at module load time (for a module) with: The addresses are normal I2C addresses. The adapter is the string name of the adapter, as shown in /sys/class/i2c-adapter/i2c-/name. -It is *NOT* i2c- itself. +It is *NOT* i2c- itself. Also, the comparison is done ignoring +spaces, so if the name is "This is an I2C chip" you can say +adapter_name=ThisisanI2cchip. This is because it's hard to pass in +spaces in kernel parameters. The debug flags are bit flags for each BMC found, they are: IPMI messages: 1, driver state: 2, timing: 4, I2C probe: 8 diff --git a/Documentation/Makefile b/Documentation/Makefile index 6883a1b9b351..bc0548201755 100644 --- a/Documentation/Makefile +++ b/Documentation/Makefile @@ -1,4 +1,4 @@ -subdir-y := accounting arm auxdisplay blackfin connector \ +subdir-y := accounting auxdisplay blackfin connector \ filesystems filesystems ia64 laptops mic misc-devices \ networking pcmcia prctl ptp spi timers vDSO video4linux \ watchdog diff --git a/Documentation/acpi/enumeration.txt b/Documentation/acpi/enumeration.txt index 750401f91341..15dfce708ebf 100644 --- a/Documentation/acpi/enumeration.txt +++ b/Documentation/acpi/enumeration.txt @@ -253,7 +253,7 @@ input driver: GPIO support ~~~~~~~~~~~~ ACPI 5 introduced two new resources to describe GPIO connections: GpioIo -and GpioInt. These resources are used be used to pass GPIO numbers used by +and GpioInt. These resources can be used to pass GPIO numbers used by the device to the driver. ACPI 5.1 extended this with _DSD (Device Specific Data) which made it possible to name the GPIOs among other things. diff --git a/Documentation/acpi/gpio-properties.txt b/Documentation/acpi/gpio-properties.txt index ae36fcf86dc7..f35dad11f0de 100644 --- a/Documentation/acpi/gpio-properties.txt +++ b/Documentation/acpi/gpio-properties.txt @@ -1,9 +1,9 @@ _DSD Device Properties Related to GPIO -------------------------------------- -With the release of ACPI 5.1 and the _DSD configuration objecte names -can finally be given to GPIOs (and other things as well) returned by -_CRS. Previously, we were only able to use an integer index to find +With the release of ACPI 5.1, the _DSD configuration object finally +allows names to be given to GPIOs (and other things as well) returned +by _CRS. Previously, we were only able to use an integer index to find the corresponding GPIO, which is pretty error prone (it depends on the _CRS output ordering, for example). diff --git a/Documentation/arm/00-INDEX b/Documentation/arm/00-INDEX index 8edb9007844e..dea011c8d7c7 100644 --- a/Documentation/arm/00-INDEX +++ b/Documentation/arm/00-INDEX @@ -10,8 +10,6 @@ IXP4xx - Intel IXP4xx Network processor. Makefile - Build sourcefiles as part of the Documentation-build for arm -msm/ - - MSM specific documentation Netwinder - Netwinder specific documentation Porting diff --git a/Documentation/arm/Makefile b/Documentation/arm/Makefile deleted file mode 100644 index 732c77050cff..000000000000 --- a/Documentation/arm/Makefile +++ /dev/null @@ -1 +0,0 @@ -subdir-y := SH-Mobile diff --git a/Documentation/arm/Marvell/README b/Documentation/arm/Marvell/README index 17453794fca5..18a775d10172 100644 --- a/Documentation/arm/Marvell/README +++ b/Documentation/arm/Marvell/README @@ -96,6 +96,11 @@ EBU Armada family 88F6820 88F6828 + Armada 390/398 Flavors: + 88F6920 + 88F6928 + Product infos: http://www.marvell.com/embedded-processors/armada-39x/ + Armada XP Flavors: MV78230 MV78260 diff --git a/Documentation/arm/SH-Mobile/Makefile b/Documentation/arm/SH-Mobile/Makefile deleted file mode 100644 index bca8a7ef6bbe..000000000000 --- a/Documentation/arm/SH-Mobile/Makefile +++ /dev/null @@ -1,7 +0,0 @@ -# List of programs to build -hostprogs-y := vrl4 - -# Tell kbuild to always build the programs -always := $(hostprogs-y) - -HOSTCFLAGS_vrl4.o += -I$(objtree)/usr/include -I$(srctree)/tools/include diff --git a/Documentation/arm/SH-Mobile/vrl4.c b/Documentation/arm/SH-Mobile/vrl4.c deleted file mode 100644 index f4cd8ad4e720..000000000000 --- a/Documentation/arm/SH-Mobile/vrl4.c +++ /dev/null @@ -1,170 +0,0 @@ -/* - * vrl4 format generator - * - * Copyright (C) 2010 Simon Horman - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - */ - -/* - * usage: vrl4 < zImage > out - * dd if=out of=/dev/sdx bs=512 seek=1 # Write the image to sector 1 - * - * Reads a zImage from stdin and writes a vrl4 image to stdout. - * In practice this means writing a padded vrl4 header to stdout followed - * by the zImage. - * - * The padding places the zImage at ALIGN bytes into the output. - * The vrl4 uses ALIGN + START_BASE as the start_address. - * This is where the mask ROM will jump to after verifying the header. - * - * The header sets copy_size to min(sizeof(zImage), MAX_BOOT_PROG_LEN) + ALIGN. - * That is, the mask ROM will load the padded header (ALIGN bytes) - * And then MAX_BOOT_PROG_LEN bytes of the image, or the entire image, - * whichever is smaller. - * - * The zImage is not modified in any way. - */ - -#define _BSD_SOURCE -#include -#include -#include -#include -#include -#include - -struct hdr { - uint32_t magic1; - uint32_t reserved1; - uint32_t magic2; - uint32_t reserved2; - uint16_t copy_size; - uint16_t boot_options; - uint32_t reserved3; - uint32_t start_address; - uint32_t reserved4; - uint32_t reserved5; - char reserved6[308]; -}; - -#define DECLARE_HDR(h) \ - struct hdr (h) = { \ - .magic1 = htole32(0xea000000), \ - .reserved1 = htole32(0x56), \ - .magic2 = htole32(0xe59ff008), \ - .reserved3 = htole16(0x1) } - -/* Align to 512 bytes, the MMCIF sector size */ -#define ALIGN_BITS 9 -#define ALIGN (1 << ALIGN_BITS) - -#define START_BASE 0xe55b0000 - -/* - * With an alignment of 512 the header uses the first sector. - * There is a 128 sector (64kbyte) limit on the data loaded by the mask ROM. - * So there are 127 sectors left for the boot programme. But in practice - * Only a small portion of a zImage is needed, 16 sectors should be more - * than enough. - * - * Note that this sets how much of the zImage is copied by the mask ROM. - * The entire zImage is present after the header and is loaded - * by the code in the boot program (which is the first portion of the zImage). - */ -#define MAX_BOOT_PROG_LEN (16 * 512) - -#define ROUND_UP(x) ((x + ALIGN - 1) & ~(ALIGN - 1)) - -static ssize_t do_read(int fd, void *buf, size_t count) -{ - size_t offset = 0; - ssize_t l; - - while (offset < count) { - l = read(fd, buf + offset, count - offset); - if (!l) - break; - if (l < 0) { - if (errno == EAGAIN || errno == EWOULDBLOCK) - continue; - perror("read"); - return -1; - } - offset += l; - } - - return offset; -} - -static ssize_t do_write(int fd, const void *buf, size_t count) -{ - size_t offset = 0; - ssize_t l; - - while (offset < count) { - l = write(fd, buf + offset, count - offset); - if (l < 0) { - if (errno == EAGAIN || errno == EWOULDBLOCK) - continue; - perror("write"); - return -1; - } - offset += l; - } - - return offset; -} - -static ssize_t write_zero(int fd, size_t len) -{ - size_t i = len; - - while (i--) { - const char x = 0; - if (do_write(fd, &x, 1) < 0) - return -1; - } - - return len; -} - -int main(void) -{ - DECLARE_HDR(hdr); - char boot_program[MAX_BOOT_PROG_LEN]; - size_t aligned_hdr_len, alligned_prog_len; - ssize_t prog_len; - - prog_len = do_read(0, boot_program, sizeof(boot_program)); - if (prog_len <= 0) - return -1; - - aligned_hdr_len = ROUND_UP(sizeof(hdr)); - hdr.start_address = htole32(START_BASE + aligned_hdr_len); - alligned_prog_len = ROUND_UP(prog_len); - hdr.copy_size = htole16(aligned_hdr_len + alligned_prog_len); - - if (do_write(1, &hdr, sizeof(hdr)) < 0) - return -1; - if (write_zero(1, aligned_hdr_len - sizeof(hdr)) < 0) - return -1; - - if (do_write(1, boot_program, prog_len) < 0) - return 1; - - /* Write out the rest of the kernel */ - while (1) { - prog_len = do_read(0, boot_program, sizeof(boot_program)); - if (prog_len < 0) - return 1; - if (prog_len == 0) - break; - if (do_write(1, boot_program, prog_len) < 0) - return 1; - } - - return 0; -} diff --git a/Documentation/arm/SH-Mobile/zboot-rom-mmcif.txt b/Documentation/arm/SH-Mobile/zboot-rom-mmcif.txt deleted file mode 100644 index efff8ae2713d..000000000000 --- a/Documentation/arm/SH-Mobile/zboot-rom-mmcif.txt +++ /dev/null @@ -1,29 +0,0 @@ -ROM-able zImage boot from MMC ------------------------------ - -An ROM-able zImage compiled with ZBOOT_ROM_MMCIF may be written to MMC and -SuperH Mobile ARM will to boot directly from the MMCIF hardware block. - -This is achieved by the mask ROM loading the first portion of the image into -MERAM and then jumping to it. This portion contains loader code which -copies the entire image to SDRAM and jumps to it. From there the zImage -boot code proceeds as normal, uncompressing the image into its final -location and then jumping to it. - -This code has been tested on an AP4EB board using the developer 1A eMMC -boot mode which is configured using the following jumper settings. -The board used for testing required a patched mask ROM in order for -this mode to function. - - 8 7 6 5 4 3 2 1 - x|x|x|x|x| |x| -S4 -+-+-+-+-+-+-+- - | | | | |x| |x on - -The zImage must be written to the MMC card at sector 1 (512 bytes) in -vrl4 format. A utility vrl4 is supplied to accomplish this. - -e.g. - vrl4 < zImage | dd of=/dev/sdX bs=512 seek=1 - -A dual-voltage MMC 4.0 card was used for testing. diff --git a/Documentation/arm/SH-Mobile/zboot-rom-sdhi.txt b/Documentation/arm/SH-Mobile/zboot-rom-sdhi.txt deleted file mode 100644 index 441959846e1a..000000000000 --- a/Documentation/arm/SH-Mobile/zboot-rom-sdhi.txt +++ /dev/null @@ -1,42 +0,0 @@ -ROM-able zImage boot from eSD ------------------------------ - -An ROM-able zImage compiled with ZBOOT_ROM_SDHI may be written to eSD and -SuperH Mobile ARM will to boot directly from the SDHI hardware block. - -This is achieved by the mask ROM loading the first portion of the image into -MERAM and then jumping to it. This portion contains loader code which -copies the entire image to SDRAM and jumps to it. From there the zImage -boot code proceeds as normal, uncompressing the image into its final -location and then jumping to it. - -This code has been tested on an mackerel board using the developer 1A eSD -boot mode which is configured using the following jumper settings. - - 8 7 6 5 4 3 2 1 - x|x|x|x| |x|x| -S4 -+-+-+-+-+-+-+- - | | | |x| | |x on - -The eSD card needs to be present in SDHI slot 1 (CN7). -As such S1 and S33 also need to be configured as per -the notes in arch/arm/mach-shmobile/board-mackerel.c. - -A partial zImage must be written to physical partition #1 (boot) -of the eSD at sector 0 in vrl4 format. A utility vrl4 is supplied to -accomplish this. - -e.g. - vrl4 < zImage | dd of=/dev/sdX bs=512 count=17 - -A full copy of _the same_ zImage should be written to physical partition #1 -(boot) of the eSD at sector 0. This should _not_ be in vrl4 format. - - vrl4 < zImage | dd of=/dev/sdX bs=512 - -Note: The commands above assume that the physical partition has been -switched. No such facility currently exists in the Linux Kernel. - -Physical partitions are described in the eSD specification. At the time of -writing they are not the same as partitions that are typically configured -using fdisk and visible through /proc/partitions diff --git a/Documentation/arm/msm/gpiomux.txt b/Documentation/arm/msm/gpiomux.txt deleted file mode 100644 index 67a81620adf6..000000000000 --- a/Documentation/arm/msm/gpiomux.txt +++ /dev/null @@ -1,176 +0,0 @@ -This document provides an overview of the msm_gpiomux interface, which -is used to provide gpio pin multiplexing and configuration on mach-msm -targets. - -History -======= - -The first-generation API for gpio configuration & multiplexing on msm -is the function gpio_tlmm_config(). This function has a few notable -shortcomings, which led to its deprecation and replacement by gpiomux: - -The 'disable' parameter: Setting the second parameter to -gpio_tlmm_config to GPIO_CFG_DISABLE tells the peripheral -processor in charge of the subsystem to perform a look-up into a -low-power table and apply the low-power/sleep setting for the pin. -As the msm family evolved this became problematic. Not all pins -have sleep settings, not all peripheral processors will accept requests -to apply said sleep settings, and not all msm targets have their gpio -subsystems managed by a peripheral processor. In order to get consistent -behavior on all targets, drivers are forced to ignore this parameter, -rendering it useless. - -The 'direction' flag: for all mux-settings other than raw-gpio (0), -the output-enable bit of a gpio is hard-wired to a known -input (usually VDD or ground). For those settings, the direction flag -is meaningless at best, and deceptive at worst. In addition, using the -direction flag to change output-enable (OE) directly can cause trouble in -gpiolib, which has no visibility into gpio direction changes made -in this way. Direction control in gpio mode should be made through gpiolib. - -Key Features of gpiomux -======================= - -- A consistent interface across all generations of msm. Drivers can expect -the same results on every target. -- gpiomux plays nicely with gpiolib. Functions that should belong to gpiolib -are left to gpiolib and not duplicated here. gpiomux is written with the -intent that gpio_chips will call gpiomux reference-counting methods -from their request() and free() hooks, providing full integration. -- Tabular configuration. Instead of having to call gpio_tlmm_config -hundreds of times, gpio configuration is placed in a single table. -- Per-gpio sleep. Each gpio is individually reference counted, allowing only -those lines which are in use to be put in high-power states. -- 0 means 'do nothing': all flags are designed so that the default memset-zero -equates to a sensible default of 'no configuration', preventing users -from having to provide hundreds of 'no-op' configs for unused or -unwanted lines. - -Usage -===== - -To use gpiomux, provide configuration information for relevant gpio lines -in the msm_gpiomux_configs table. Since a 0 equates to "unconfigured", -only those lines to be managed by gpiomux need to be specified. Here -is a completely fictional example: - -struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS] = { - [12] = { - .active = GPIOMUX_VALID | GPIOMUX_DRV_8MA | GPIOMUX_FUNC_1, - .suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN, - }, - [34] = { - .suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN, - }, -}; - -To indicate that a gpio is in use, call msm_gpiomux_get() to increase -its reference count. To decrease the reference count, call msm_gpiomux_put(). - -The effect of this configuration is as follows: - -When the system boots, gpios 12 and 34 will be initialized with their -'suspended' configurations. All other gpios, which were left unconfigured, -will not be touched. - -When msm_gpiomux_get() is called on gpio 12 to raise its reference count -above 0, its active configuration will be applied. Since no other gpio -line has a valid active configuration, msm_gpiomux_get() will have no -effect on any other line. - -When msm_gpiomux_put() is called on gpio 12 or 34 to drop their reference -count to 0, their suspended configurations will be applied. -Since no other gpio line has a valid suspended configuration, no other -gpio line will be effected by msm_gpiomux_put(). Since gpio 34 has no valid -active configuration, this is effectively a no-op for gpio 34 as well, -with one small caveat, see the section "About Output-Enable Settings". - -All of the GPIOMUX_VALID flags may seem like unnecessary overhead, but -they address some important issues. As unused entries (all those -except 12 and 34) are zero-filled, gpiomux needs a way to distinguish -the used fields from the unused. In addition, the all-zero pattern -is a valid configuration! Therefore, gpiomux defines an additional bit -which is used to indicate when a field is used. This has the pleasant -side-effect of allowing calls to msm_gpiomux_write to use '0' to indicate -that a value should not be changed: - - msm_gpiomux_write(0, GPIOMUX_VALID, 0); - -replaces the active configuration of gpio 0 with an all-zero configuration, -but leaves the suspended configuration as it was. - -Static Configurations -===================== - -To install a static configuration, which is applied at boot and does -not change after that, install a configuration with a suspended component -but no active component, as in the previous example: - - [34] = { - .suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN, - }, - -The suspended setting is applied during boot, and the lack of any valid -active setting prevents any other setting from being applied at runtime. -If other subsystems attempting to access the line is a concern, one could -*really* anchor the configuration down by calling msm_gpiomux_get on the -line at initialization to move the line into active mode. With the line -held, it will never be re-suspended, and with no valid active configuration, -no new configurations will be applied. - -But then, if having other subsystems grabbing for the line is truly a concern, -it should be reserved with gpio_request instead, which carries an implicit -msm_gpiomux_get. - -gpiomux and gpiolib -=================== - -It is expected that msm gpio_chips will call msm_gpiomux_get() and -msm_gpiomux_put() from their request and free hooks, like this fictional -example: - -static int request(struct gpio_chip *chip, unsigned offset) -{ - return msm_gpiomux_get(chip->base + offset); -} - -static void free(struct gpio_chip *chip, unsigned offset) -{ - msm_gpiomux_put(chip->base + offset); -} - - ...somewhere in a gpio_chip declaration... - .request = request, - .free = free, - -This provides important functionality: -- It guarantees that a gpio line will have its 'active' config applied - when the line is requested, and will not be suspended while the line - remains requested; and -- It guarantees that gpio-direction settings from gpiolib behave sensibly. - See "About Output-Enable Settings." - -This mechanism allows for "auto-request" of gpiomux lines via gpiolib -when it is suitable. Drivers wishing more exact control are, of course, -free to also use msm_gpiomux_set and msm_gpiomux_get. - -About Output-Enable Settings -============================ - -Some msm targets do not have the ability to query the current gpio -configuration setting. This means that changes made to the output-enable -(OE) bit by gpiolib cannot be consistently detected and preserved by gpiomux. -Therefore, when gpiomux applies a configuration setting, any direction -settings which may have been applied by gpiolib are lost and the default -input settings are re-applied. - -For this reason, drivers should not assume that gpio direction settings -continue to hold if they free and then re-request a gpio. This seems like -common sense - after all, anybody could have obtained the line in the -meantime - but it needs saying. - -This also means that calls to msm_gpiomux_write will reset the OE bit, -which means that if the gpio line is held by a client of gpiolib and -msm_gpiomux_write is called, the direction setting has been lost and -gpiolib's internal state has been broken. -Release gpio lines before reconfiguring them. diff --git a/Documentation/arm64/acpi_object_usage.txt b/Documentation/arm64/acpi_object_usage.txt new file mode 100644 index 000000000000..a6e1a1805e51 --- /dev/null +++ b/Documentation/arm64/acpi_object_usage.txt @@ -0,0 +1,593 @@ +ACPI Tables +----------- +The expectations of individual ACPI tables are discussed in the list that +follows. + +If a section number is used, it refers to a section number in the ACPI +specification where the object is defined. If "Signature Reserved" is used, +the table signature (the first four bytes of the table) is the only portion +of the table recognized by the specification, and the actual table is defined +outside of the UEFI Forum (see Section 5.2.6 of the specification). + +For ACPI on arm64, tables also fall into the following categories: + + -- Required: DSDT, FADT, GTDT, MADT, MCFG, RSDP, SPCR, XSDT + + -- Recommended: BERT, EINJ, ERST, HEST, SSDT + + -- Optional: BGRT, CPEP, CSRT, DRTM, ECDT, FACS, FPDT, MCHI, MPST, + MSCT, RASF, SBST, SLIT, SPMI, SRAT, TCPA, TPM2, UEFI + + -- Not supported: BOOT, DBG2, DBGP, DMAR, ETDT, HPET, IBFT, IVRS, + LPIT, MSDM, RSDT, SLIC, WAET, WDAT, WDRT, WPBT + + +Table Usage for ARMv8 Linux +----- ---------------------------------------------------------------- +BERT Section 18.3 (signature == "BERT") + == Boot Error Record Table == + Must be supplied if RAS support is provided by the platform. It + is recommended this table be supplied. + +BOOT Signature Reserved (signature == "BOOT") + == simple BOOT flag table == + Microsoft only table, will not be supported. + +BGRT Section 5.2.22 (signature == "BGRT") + == Boot Graphics Resource Table == + Optional, not currently supported, with no real use-case for an + ARM server. + +CPEP Section 5.2.18 (signature == "CPEP") + == Corrected Platform Error Polling table == + Optional, not currently supported, and not recommended until such + time as ARM-compatible hardware is available, and the specification + suitably modified. + +CSRT Signature Reserved (signature == "CSRT") + == Core System Resources Table == + Optional, not currently supported. + +DBG2 Signature Reserved (signature == "DBG2") + == DeBuG port table 2 == + Microsoft only table, will not be supported. + +DBGP Signature Reserved (signature == "DBGP") + == DeBuG Port table == + Microsoft only table, will not be supported. + +DSDT Section 5.2.11.1 (signature == "DSDT") + == Differentiated System Description Table == + A DSDT is required; see also SSDT. + + ACPI tables contain only one DSDT but can contain one or more SSDTs, + which are optional. Each SSDT can only add to the ACPI namespace, + but cannot modify or replace anything in the DSDT. + +DMAR Signature Reserved (signature == "DMAR") + == DMA Remapping table == + x86 only table, will not be supported. + +DRTM Signature Reserved (signature == "DRTM") + == Dynamic Root of Trust for Measurement table == + Optional, not currently supported. + +ECDT Section 5.2.16 (signature == "ECDT") + == Embedded Controller Description Table == + Optional, not currently supported, but could be used on ARM if and + only if one uses the GPE_BIT field to represent an IRQ number, since + there are no GPE blocks defined in hardware reduced mode. This would + need to be modified in the ACPI specification. + +EINJ Section 18.6 (signature == "EINJ") + == Error Injection table == + This table is very useful for testing platform response to error + conditions; it allows one to inject an error into the system as + if it had actually occurred. However, this table should not be + shipped with a production system; it should be dynamically loaded + and executed with the ACPICA tools only during testing. + +ERST Section 18.5 (signature == "ERST") + == Error Record Serialization Table == + On a platform supports RAS, this table must be supplied if it is not + UEFI-based; if it is UEFI-based, this table may be supplied. When this + table is not present, UEFI run time service will be utilized to save + and retrieve hardware error information to and from a persistent store. + +ETDT Signature Reserved (signature == "ETDT") + == Event Timer Description Table == + Obsolete table, will not be supported. + +FACS Section 5.2.10 (signature == "FACS") + == Firmware ACPI Control Structure == + It is unlikely that this table will be terribly useful. If it is + provided, the Global Lock will NOT be used since it is not part of + the hardware reduced profile, and only 64-bit address fields will + be considered valid. + +FADT Section 5.2.9 (signature == "FACP") + == Fixed ACPI Description Table == + Required for arm64. + + The HW_REDUCED_ACPI flag must be set. All of the fields that are + to be ignored when HW_REDUCED_ACPI is set are expected to be set to + zero. + + If an FACS table is provided, the X_FIRMWARE_CTRL field is to be + used, not FIRMWARE_CTRL. + + If PSCI is used (as is recommended), make sure that ARM_BOOT_ARCH is + filled in properly -- that the PSCI_COMPLIANT flag is set and that + PSCI_USE_HVC is set or unset as needed (see table 5-37). + + For the DSDT that is also required, the X_DSDT field is to be used, + not the DSDT field. + +FPDT Section 5.2.23 (signature == "FPDT") + == Firmware Performance Data Table == + Optional, not currently supported. + +GTDT Section 5.2.24 (signature == "GTDT") + == Generic Timer Description Table == + Required for arm64. + +HEST Section 18.3.2 (signature == "HEST") + == Hardware Error Source Table == + Until further error source types are defined, use only types 6 (AER + Root Port), 7 (AER Endpoint), 8 (AER Bridge), or 9 (Generic Hardware + Error Source). Firmware first error handling is possible if and only + if Trusted Firmware is being used on arm64. + + Must be supplied if RAS support is provided by the platform. It + is recommended this table be supplied. + +HPET Signature Reserved (signature == "HPET") + == High Precision Event timer Table == + x86 only table, will not be supported. + +IBFT Signature Reserved (signature == "IBFT") + == iSCSI Boot Firmware Table == + Microsoft defined table, support TBD. + +IVRS Signature Reserved (signature == "IVRS") + == I/O Virtualization Reporting Structure == + x86_64 (AMD) only table, will not be supported. + +LPIT Signature Reserved (signature == "LPIT") + == Low Power Idle Table == + x86 only table as of ACPI 5.1; future versions have been adapted for + use with ARM and will be recommended in order to support ACPI power + management. + +MADT Section 5.2.12 (signature == "APIC") + == Multiple APIC Description Table == + Required for arm64. Only the GIC interrupt controller structures + should be used (types 0xA - 0xE). + +MCFG Signature Reserved (signature == "MCFG") + == Memory-mapped ConFiGuration space == + If the platform supports PCI/PCIe, an MCFG table is required. + +MCHI Signature Reserved (signature == "MCHI") + == Management Controller Host Interface table == + Optional, not currently supported. + +MPST Section 5.2.21 (signature == "MPST") + == Memory Power State Table == + Optional, not currently supported. + +MSDM Signature Reserved (signature == "MSDM") + == Microsoft Data Management table == + Microsoft only table, will not be supported. + +MSCT Section 5.2.19 (signature == "MSCT") + == Maximum System Characteristic Table == + Optional, not currently supported. + +RASF Section 5.2.20 (signature == "RASF") + == RAS Feature table == + Optional, not currently supported. + +RSDP Section 5.2.5 (signature == "RSD PTR") + == Root System Description PoinTeR == + Required for arm64. + +RSDT Section 5.2.7 (signature == "RSDT") + == Root System Description Table == + Since this table can only provide 32-bit addresses, it is deprecated + on arm64, and will not be used. + +SBST Section 5.2.14 (signature == "SBST") + == Smart Battery Subsystem Table == + Optional, not currently supported. + +SLIC Signature Reserved (signature == "SLIC") + == Software LIcensing table == + Microsoft only table, will not be supported. + +SLIT Section 5.2.17 (signature == "SLIT") + == System Locality distance Information Table == + Optional in general, but required for NUMA systems. + +SPCR Signature Reserved (signature == "SPCR") + == Serial Port Console Redirection table == + Required for arm64. + +SPMI Signature Reserved (signature == "SPMI") + == Server Platform Management Interface table == + Optional, not currently supported. + +SRAT Section 5.2.16 (signature == "SRAT") + == System Resource Affinity Table == + Optional, but if used, only the GICC Affinity structures are read. + To support NUMA, this table is required. + +SSDT Section 5.2.11.2 (signature == "SSDT") + == Secondary System Description Table == + These tables are a continuation of the DSDT; these are recommended + for use with devices that can be added to a running system, but can + also serve the purpose of dividing up device descriptions into more + manageable pieces. + + An SSDT can only ADD to the ACPI namespace. It cannot modify or + replace existing device descriptions already in the namespace. + + These tables are optional, however. ACPI tables should contain only + one DSDT but can contain many SSDTs. + +TCPA Signature Reserved (signature == "TCPA") + == Trusted Computing Platform Alliance table == + Optional, not currently supported, and may need changes to fully + interoperate with arm64. + +TPM2 Signature Reserved (signature == "TPM2") + == Trusted Platform Module 2 table == + Optional, not currently supported, and may need changes to fully + interoperate with arm64. + +UEFI Signature Reserved (signature == "UEFI") + == UEFI ACPI data table == + Optional, not currently supported. No known use case for arm64, + at present. + +WAET Signature Reserved (signature == "WAET") + == Windows ACPI Emulated devices Table == + Microsoft only table, will not be supported. + +WDAT Signature Reserved (signature == "WDAT") + == Watch Dog Action Table == + Microsoft only table, will not be supported. + +WDRT Signature Reserved (signature == "WDRT") + == Watch Dog Resource Table == + Microsoft only table, will not be supported. + +WPBT Signature Reserved (signature == "WPBT") + == Windows Platform Binary Table == + Microsoft only table, will not be supported. + +XSDT Section 5.2.8 (signature == "XSDT") + == eXtended System Description Table == + Required for arm64. + + +ACPI Objects +------------ +The expectations on individual ACPI objects are discussed in the list that +follows: + +Name Section Usage for ARMv8 Linux +---- ------------ ------------------------------------------------- +_ADR 6.1.1 Use as needed. + +_BBN 6.5.5 Use as needed; PCI-specific. + +_BDN 6.5.3 Optional; not likely to be used on arm64. + +_CCA 6.2.17 This method should be defined for all bus masters + on arm64. While cache coherency is assumed, making + it explicit ensures the kernel will set up DMA as + it should. + +_CDM 6.2.1 Optional, to be used only for processor devices. + +_CID 6.1.2 Use as needed. + +_CLS 6.1.3 Use as needed. + +_CRS 6.2.2 Required on arm64. + +_DCK 6.5.2 Optional; not likely to be used on arm64. + +_DDN 6.1.4 This field can be used for a device name. However, + it is meant for DOS device names (e.g., COM1), so be + careful of its use across OSes. + +_DEP 6.5.8 Use as needed. + +_DIS 6.2.3 Optional, for power management use. + +_DLM 5.7.5 Optional. + +_DMA 6.2.4 Optional. + +_DSD 6.2.5 To be used with caution. If this object is used, try + to use it within the constraints already defined by the + Device Properties UUID. Only in rare circumstances + should it be necessary to create a new _DSD UUID. + + In either case, submit the _DSD definition along with + any driver patches for discussion, especially when + device properties are used. A driver will not be + considered complete without a corresponding _DSD + description. Once approved by kernel maintainers, + the UUID or device properties must then be registered + with the UEFI Forum; this may cause some iteration as + more than one OS will be registering entries. + +_DSM Do not use this method. It is not standardized, the + return values are not well documented, and it is + currently a frequent source of error. + +_DSW 7.2.1 Use as needed; power management specific. + +_EDL 6.3.1 Optional. + +_EJD 6.3.2 Optional. + +_EJx 6.3.3 Optional. + +_FIX 6.2.7 x86 specific, not used on arm64. + +\_GL 5.7.1 This object is not to be used in hardware reduced + mode, and therefore should not be used on arm64. + +_GLK 6.5.7 This object requires a global lock be defined; there + is no global lock on arm64 since it runs in hardware + reduced mode. Hence, do not use this object on arm64. + +\_GPE 5.3.1 This namespace is for x86 use only. Do not use it + on arm64. + +_GSB 6.2.7 Optional. + +_HID 6.1.5 Use as needed. This is the primary object to use in + device probing, though _CID and _CLS may also be used. + +_HPP 6.2.8 Optional, PCI specific. + +_HPX 6.2.9 Optional, PCI specific. + +_HRV 6.1.6 Optional, use as needed to clarify device behavior; in + some cases, this may be easier to use than _DSD. + +_INI 6.5.1 Not required, but can be useful in setting up devices + when UEFI leaves them in a state that may not be what + the driver expects before it starts probing. + +_IRC 7.2.15 Use as needed; power management specific. + +_LCK 6.3.4 Optional. + +_MAT 6.2.10 Optional; see also the MADT. + +_MLS 6.1.7 Optional, but highly recommended for use in + internationalization. + +_OFF 7.1.2 It is recommended to define this method for any device + that can be turned on or off. + +_ON 7.1.3 It is recommended to define this method for any device + that can be turned on or off. + +\_OS 5.7.3 This method will return "Linux" by default (this is + the value of the macro ACPI_OS_NAME on Linux). The + command line parameter acpi_os= can be used + to set it to some other value. + +_OSC 6.2.11 This method can be a global method in ACPI (i.e., + \_SB._OSC), or it may be associated with a specific + device (e.g., \_SB.DEV0._OSC), or both. When used + as a global method, only capabilities published in + the ACPI specification are allowed. When used as + a device-specific method, the process described for + using _DSD MUST be used to create an _OSC definition; + out-of-process use of _OSC is not allowed. That is, + submit the device-specific _OSC usage description as + part of the kernel driver submission, get it approved + by the kernel community, then register it with the + UEFI Forum. + +\_OSI 5.7.2 Deprecated on ARM64. Any invocation of this method + will print a warning on the console and return false. + That is, as far as ACPI firmware is concerned, _OSI + cannot be used to determine what sort of system is + being used or what functionality is provided. The + _OSC method is to be used instead. + +_OST 6.3.5 Optional. + +_PDC 8.4.1 Deprecated, do not use on arm64. + +\_PIC 5.8.1 The method should not be used. On arm64, the only + interrupt model available is GIC. + +_PLD 6.1.8 Optional. + +\_PR 5.3.1 This namespace is for x86 use only on legacy systems. + Do not use it on arm64. + +_PRS 6.2.12 Optional. + +_PRT 6.2.13 Required as part of the definition of all PCI root + devices. + +_PRW 7.2.13 Use as needed; power management specific. + +_PRx 7.2.8-11 Use as needed; power management specific. If _PR0 is + defined, _PR3 must also be defined. + +_PSC 7.2.6 Use as needed; power management specific. + +_PSE 7.2.7 Use as needed; power management specific. + +_PSW 7.2.14 Use as needed; power management specific. + +_PSx 7.2.2-5 Use as needed; power management specific. If _PS0 is + defined, _PS3 must also be defined. If clocks or + regulators need adjusting to be consistent with power + usage, change them in these methods. + +\_PTS 7.3.1 Use as needed; power management specific. + +_PXM 6.2.14 Optional. + +_REG 6.5.4 Use as needed. + +\_REV 5.7.4 Always returns the latest version of ACPI supported. + +_RMV 6.3.6 Optional. + +\_SB 5.3.1 Required on arm64; all devices must be defined in this + namespace. + +_SEG 6.5.6 Use as needed; PCI-specific. + +\_SI 5.3.1, Optional. + 9.1 + +_SLI 6.2.15 Optional; recommended when SLIT table is in use. + +_STA 6.3.7, It is recommended to define this method for any device + 7.1.4 that can be turned on or off. + +_SRS 6.2.16 Optional; see also _PRS. + +_STR 6.1.10 Recommended for conveying device names to end users; + this is preferred over using _DDN. + +_SUB 6.1.9 Use as needed; _HID or _CID are preferred. + +_SUN 6.1.11 Optional. + +\_Sx 7.3.2 Use as needed; power management specific. + +_SxD 7.2.16-19 Use as needed; power management specific. + +_SxW 7.2.20-24 Use as needed; power management specific. + +_SWS 7.3.3 Use as needed; power management specific; this may + require specification changes for use on arm64. + +\_TTS 7.3.4 Use as needed; power management specific. + +\_TZ 5.3.1 Optional. + +_UID 6.1.12 Recommended for distinguishing devices of the same + class; define it if at all possible. + +\_WAK 7.3.5 Use as needed; power management specific. + + +ACPI Event Model +---------------- +Do not use GPE block devices; these are not supported in the hardware reduced +profile used by arm64. Since there are no GPE blocks defined for use on ARM +platforms, GPIO-signaled interrupts should be used for creating system events. + + +ACPI Processor Control +---------------------- +Section 8 of the ACPI specification is currently undergoing change that +should be completed in the 6.0 version of the specification. Processor +performance control will be handled differently for arm64 at that point +in time. Processor aggregator devices (section 8.5) will not be used, +for example, but another similar mechanism instead. + +While UEFI constrains what we can say until the release of 6.0, it is +recommended that CPPC (8.4.5) be used as the primary model. This will +still be useful into the future. C-states and P-states will still be +provided, but most of the current design work appears to favor CPPC. + +Further, it is essential that the ARMv8 SoC provide a fully functional +implementation of PSCI; this will be the only mechanism supported by ACPI +to control CPU power state (including secondary CPU booting). + +More details will be provided on the release of the ACPI 6.0 specification. + + +ACPI System Address Map Interfaces +---------------------------------- +In Section 15 of the ACPI specification, several methods are mentioned as +possible mechanisms for conveying memory resource information to the kernel. +For arm64, we will only support UEFI for booting with ACPI, hence the UEFI +GetMemoryMap() boot service is the only mechanism that will be used. + + +ACPI Platform Error Interfaces (APEI) +------------------------------------- +The APEI tables supported are described above. + +APEI requires the equivalent of an SCI and an NMI on ARMv8. The SCI is used +to notify the OSPM of errors that have occurred but can be corrected and the +system can continue correct operation, even if possibly degraded. The NMI is +used to indicate fatal errors that cannot be corrected, and require immediate +attention. + +Since there is no direct equivalent of the x86 SCI or NMI, arm64 handles +these slightly differently. The SCI is handled as a normal GPIO-signaled +interrupt; given that these are corrected (or correctable) errors being +reported, this is sufficient. The NMI is emulated as the highest priority +GPIO-signaled interrupt possible. This implies some caution must be used +since there could be interrupts at higher privilege levels or even interrupts +at the same priority as the emulated NMI. In Linux, this should not be the +case but one should be aware it could happen. + + +ACPI Objects Not Supported on ARM64 +----------------------------------- +While this may change in the future, there are several classes of objects +that can be defined, but are not currently of general interest to ARM servers. + +These are not supported: + + -- Section 9.2: ambient light sensor devices + + -- Section 9.3: battery devices + + -- Section 9.4: lids (e.g., laptop lids) + + -- Section 9.8.2: IDE controllers + + -- Section 9.9: floppy controllers + + -- Section 9.10: GPE block devices + + -- Section 9.15: PC/AT RTC/CMOS devices + + -- Section 9.16: user presence detection devices + + -- Section 9.17: I/O APIC devices; all GICs must be enumerable via MADT + + -- Section 9.18: time and alarm devices (see 9.15) + + +ACPI Objects Not Yet Implemented +-------------------------------- +While these objects have x86 equivalents, and they do make some sense in ARM +servers, there is either no hardware available at present, or in some cases +there may not yet be a non-ARM implementation. Hence, they are currently not +implemented though that may change in the future. + +Not yet implemented are: + + -- Section 10: power source and power meter devices + + -- Section 11: thermal management + + -- Section 12: embedded controllers interface + + -- Section 13: SMBus interfaces + + -- Section 17: NUMA support (prototypes have been submitted for + review) diff --git a/Documentation/arm64/arm-acpi.txt b/Documentation/arm64/arm-acpi.txt new file mode 100644 index 000000000000..570a4f8e1a01 --- /dev/null +++ b/Documentation/arm64/arm-acpi.txt @@ -0,0 +1,505 @@ +ACPI on ARMv8 Servers +--------------------- +ACPI can be used for ARMv8 general purpose servers designed to follow +the ARM SBSA (Server Base System Architecture) [0] and SBBR (Server +Base Boot Requirements) [1] specifications. Please note that the SBBR +can be retrieved simply by visiting [1], but the SBSA is currently only +available to those with an ARM login due to ARM IP licensing concerns. + +The ARMv8 kernel implements the reduced hardware model of ACPI version +5.1 or later. Links to the specification and all external documents +it refers to are managed by the UEFI Forum. The specification is +available at http://www.uefi.org/specifications and documents referenced +by the specification can be found via http://www.uefi.org/acpi. + +If an ARMv8 system does not meet the requirements of the SBSA and SBBR, +or cannot be described using the mechanisms defined in the required ACPI +specifications, then ACPI may not be a good fit for the hardware. + +While the documents mentioned above set out the requirements for building +industry-standard ARMv8 servers, they also apply to more than one operating +system. The purpose of this document is to describe the interaction between +ACPI and Linux only, on an ARMv8 system -- that is, what Linux expects of +ACPI and what ACPI can expect of Linux. + + +Why ACPI on ARM? +---------------- +Before examining the details of the interface between ACPI and Linux, it is +useful to understand why ACPI is being used. Several technologies already +exist in Linux for describing non-enumerable hardware, after all. In this +section we summarize a blog post [2] from Grant Likely that outlines the +reasoning behind ACPI on ARMv8 servers. Actually, we snitch a good portion +of the summary text almost directly, to be honest. + +The short form of the rationale for ACPI on ARM is: + +-- ACPI’s bytecode (AML) allows the platform to encode hardware behavior, + while DT explicitly does not support this. For hardware vendors, being + able to encode behavior is a key tool used in supporting operating + system releases on new hardware. + +-- ACPI’s OSPM defines a power management model that constrains what the + platform is allowed to do into a specific model, while still providing + flexibility in hardware design. + +-- In the enterprise server environment, ACPI has established bindings (such + as for RAS) which are currently used in production systems. DT does not. + Such bindings could be defined in DT at some point, but doing so means ARM + and x86 would end up using completely different code paths in both firmware + and the kernel. + +-- Choosing a single interface to describe the abstraction between a platform + and an OS is important. Hardware vendors would not be required to implement + both DT and ACPI if they want to support multiple operating systems. And, + agreeing on a single interface instead of being fragmented into per OS + interfaces makes for better interoperability overall. + +-- The new ACPI governance process works well and Linux is now at the same + table as hardware vendors and other OS vendors. In fact, there is no + longer any reason to feel that ACPI is only belongs to Windows or that + Linux is in any way secondary to Microsoft in this arena. The move of + ACPI governance into the UEFI forum has significantly opened up the + specification development process, and currently, a large portion of the + changes being made to ACPI is being driven by Linux. + +Key to the use of ACPI is the support model. For servers in general, the +responsibility for hardware behaviour cannot solely be the domain of the +kernel, but rather must be split between the platform and the kernel, in +order to allow for orderly change over time. ACPI frees the OS from needing +to understand all the minute details of the hardware so that the OS doesn’t +need to be ported to each and every device individually. It allows the +hardware vendors to take responsibility for power management behaviour without +depending on an OS release cycle which is not under their control. + +ACPI is also important because hardware and OS vendors have already worked +out the mechanisms for supporting a general purpose computing ecosystem. The +infrastructure is in place, the bindings are in place, and the processes are +in place. DT does exactly what Linux needs it to when working with vertically +integrated devices, but there are no good processes for supporting what the +server vendors need. Linux could potentially get there with DT, but doing so +really just duplicates something that already works. ACPI already does what +the hardware vendors need, Microsoft won’t collaborate on DT, and hardware +vendors would still end up providing two completely separate firmware +interfaces -- one for Linux and one for Windows. + + +Kernel Compatibility +-------------------- +One of the primary motivations for ACPI is standardization, and using that +to provide backward compatibility for Linux kernels. In the server market, +software and hardware are often used for long periods. ACPI allows the +kernel and firmware to agree on a consistent abstraction that can be +maintained over time, even as hardware or software change. As long as the +abstraction is supported, systems can be updated without necessarily having +to replace the kernel. + +When a Linux driver or subsystem is first implemented using ACPI, it by +definition ends up requiring a specific version of the ACPI specification +-- it's baseline. ACPI firmware must continue to work, even though it may +not be optimal, with the earliest kernel version that first provides support +for that baseline version of ACPI. There may be a need for additional drivers, +but adding new functionality (e.g., CPU power management) should not break +older kernel versions. Further, ACPI firmware must also work with the most +recent version of the kernel. + + +Relationship with Device Tree +----------------------------- +ACPI support in drivers and subsystems for ARMv8 should never be mutually +exclusive with DT support at compile time. + +At boot time the kernel will only use one description method depending on +parameters passed from the bootloader (including kernel bootargs). + +Regardless of whether DT or ACPI is used, the kernel must always be capable +of booting with either scheme (in kernels with both schemes enabled at compile +time). + + +Booting using ACPI tables +------------------------- +The only defined method for passing ACPI tables to the kernel on ARMv8 +is via the UEFI system configuration table. Just so it is explicit, this +means that ACPI is only supported on platforms that boot via UEFI. + +When an ARMv8 system boots, it can either have DT information, ACPI tables, +or in some very unusual cases, both. If no command line parameters are used, +the kernel will try to use DT for device enumeration; if there is no DT +present, the kernel will try to use ACPI tables, but only if they are present. +In neither is available, the kernel will not boot. If acpi=force is used +on the command line, the kernel will attempt to use ACPI tables first, but +fall back to DT if there are no ACPI tables present. The basic idea is that +the kernel will not fail to boot unless it absolutely has no other choice. + +Processing of ACPI tables may be disabled by passing acpi=off on the kernel +command line; this is the default behavior. + +In order for the kernel to load and use ACPI tables, the UEFI implementation +MUST set the ACPI_20_TABLE_GUID to point to the RSDP table (the table with +the ACPI signature "RSD PTR "). If this pointer is incorrect and acpi=force +is used, the kernel will disable ACPI and try to use DT to boot instead; the +kernel has, in effect, determined that ACPI tables are not present at that +point. + +If the pointer to the RSDP table is correct, the table will be mapped into +the kernel by the ACPI core, using the address provided by UEFI. + +The ACPI core will then locate and map in all other ACPI tables provided by +using the addresses in the RSDP table to find the XSDT (eXtended System +Description Table). The XSDT in turn provides the addresses to all other +ACPI tables provided by the system firmware; the ACPI core will then traverse +this table and map in the tables listed. + +The ACPI core will ignore any provided RSDT (Root System Description Table). +RSDTs have been deprecated and are ignored on arm64 since they only allow +for 32-bit addresses. + +Further, the ACPI core will only use the 64-bit address fields in the FADT +(Fixed ACPI Description Table). Any 32-bit address fields in the FADT will +be ignored on arm64. + +Hardware reduced mode (see Section 4.1 of the ACPI 5.1 specification) will +be enforced by the ACPI core on arm64. Doing so allows the ACPI core to +run less complex code since it no longer has to provide support for legacy +hardware from other architectures. Any fields that are not to be used for +hardware reduced mode must be set to zero. + +For the ACPI core to operate properly, and in turn provide the information +the kernel needs to configure devices, it expects to find the following +tables (all section numbers refer to the ACPI 5.1 specfication): + + -- RSDP (Root System Description Pointer), section 5.2.5 + + -- XSDT (eXtended System Description Table), section 5.2.8 + + -- FADT (Fixed ACPI Description Table), section 5.2.9 + + -- DSDT (Differentiated System Description Table), section + 5.2.11.1 + + -- MADT (Multiple APIC Description Table), section 5.2.12 + + -- GTDT (Generic Timer Description Table), section 5.2.24 + + -- If PCI is supported, the MCFG (Memory mapped ConFiGuration + Table), section 5.2.6, specifically Table 5-31. + +If the above tables are not all present, the kernel may or may not be +able to boot properly since it may not be able to configure all of the +devices available. + + +ACPI Detection +-------------- +Drivers should determine their probe() type by checking for a null +value for ACPI_HANDLE, or checking .of_node, or other information in +the device structure. This is detailed further in the "Driver +Recommendations" section. + +In non-driver code, if the presence of ACPI needs to be detected at +runtime, then check the value of acpi_disabled. If CONFIG_ACPI is not +set, acpi_disabled will always be 1. + + +Device Enumeration +------------------ +Device descriptions in ACPI should use standard recognized ACPI interfaces. +These may contain less information than is typically provided via a Device +Tree description for the same device. This is also one of the reasons that +ACPI can be useful -- the driver takes into account that it may have less +detailed information about the device and uses sensible defaults instead. +If done properly in the driver, the hardware can change and improve over +time without the driver having to change at all. + +Clocks provide an excellent example. In DT, clocks need to be specified +and the drivers need to take them into account. In ACPI, the assumption +is that UEFI will leave the device in a reasonable default state, including +any clock settings. If for some reason the driver needs to change a clock +value, this can be done in an ACPI method; all the driver needs to do is +invoke the method and not concern itself with what the method needs to do +to change the clock. Changing the hardware can then take place over time +by changing what the ACPI method does, and not the driver. + +In DT, the parameters needed by the driver to set up clocks as in the example +above are known as "bindings"; in ACPI, these are known as "Device Properties" +and provided to a driver via the _DSD object. + +ACPI tables are described with a formal language called ASL, the ACPI +Source Language (section 19 of the specification). This means that there +are always multiple ways to describe the same thing -- including device +properties. For example, device properties could use an ASL construct +that looks like this: Name(KEY0, "value0"). An ACPI device driver would +then retrieve the value of the property by evaluating the KEY0 object. +However, using Name() this way has multiple problems: (1) ACPI limits +names ("KEY0") to four characters unlike DT; (2) there is no industry +wide registry that maintains a list of names, minimzing re-use; (3) +there is also no registry for the definition of property values ("value0"), +again making re-use difficult; and (4) how does one maintain backward +compatibility as new hardware comes out? The _DSD method was created +to solve precisely these sorts of problems; Linux drivers should ALWAYS +use the _DSD method for device properties and nothing else. + +The _DSM object (ACPI Section 9.14.1) could also be used for conveying +device properties to a driver. Linux drivers should only expect it to +be used if _DSD cannot represent the data required, and there is no way +to create a new UUID for the _DSD object. Note that there is even less +regulation of the use of _DSM than there is of _DSD. Drivers that depend +on the contents of _DSM objects will be more difficult to maintain over +time because of this; as of this writing, the use of _DSM is the cause +of quite a few firmware problems and is not recommended. + +Drivers should look for device properties in the _DSD object ONLY; the _DSD +object is described in the ACPI specification section 6.2.5, but this only +describes how to define the structure of an object returned via _DSD, and +how specific data structures are defined by specific UUIDs. Linux should +only use the _DSD Device Properties UUID [5]: + + -- UUID: daffd814-6eba-4d8c-8a91-bc9bbf4aa301 + + -- http://www.uefi.org/sites/default/files/resources/_DSD-device-properties-UUID.pdf + +The UEFI Forum provides a mechanism for registering device properties [4] +so that they may be used across all operating systems supporting ACPI. +Device properties that have not been registered with the UEFI Forum should +not be used. + +Before creating new device properties, check to be sure that they have not +been defined before and either registered in the Linux kernel documentation +as DT bindings, or the UEFI Forum as device properties. While we do not want +to simply move all DT bindings into ACPI device properties, we can learn from +what has been previously defined. + +If it is necessary to define a new device property, or if it makes sense to +synthesize the definition of a binding so it can be used in any firmware, +both DT bindings and ACPI device properties for device drivers have review +processes. Use them both. When the driver itself is submitted for review +to the Linux mailing lists, the device property definitions needed must be +submitted at the same time. A driver that supports ACPI and uses device +properties will not be considered complete without their definitions. Once +the device property has been accepted by the Linux community, it must be +registered with the UEFI Forum [4], which will review it again for consistency +within the registry. This may require iteration. The UEFI Forum, though, +will always be the canonical site for device property definitions. + +It may make sense to provide notice to the UEFI Forum that there is the +intent to register a previously unused device property name as a means of +reserving the name for later use. Other operating system vendors will +also be submitting registration requests and this may help smooth the +process. + +Once registration and review have been completed, the kernel provides an +interface for looking up device properties in a manner independent of +whether DT or ACPI is being used. This API should be used [6]; it can +eliminate some duplication of code paths in driver probing functions and +discourage divergence between DT bindings and ACPI device properties. + + +Programmable Power Control Resources +------------------------------------ +Programmable power control resources include such resources as voltage/current +providers (regulators) and clock sources. + +With ACPI, the kernel clock and regulator framework is not expected to be used +at all. + +The kernel assumes that power control of these resources is represented with +Power Resource Objects (ACPI section 7.1). The ACPI core will then handle +correctly enabling and disabling resources as they are needed. In order to +get that to work, ACPI assumes each device has defined D-states and that these +can be controlled through the optional ACPI methods _PS0, _PS1, _PS2, and _PS3; +in ACPI, _PS0 is the method to invoke to turn a device full on, and _PS3 is for +turning a device full off. + +There are two options for using those Power Resources. They can: + + -- be managed in a _PSx method which gets called on entry to power + state Dx. + + -- be declared separately as power resources with their own _ON and _OFF + methods. They are then tied back to D-states for a particular device + via _PRx which specifies which power resources a device needs to be on + while in Dx. Kernel then tracks number of devices using a power resource + and calls _ON/_OFF as needed. + +The kernel ACPI code will also assume that the _PSx methods follow the normal +ACPI rules for such methods: + + -- If either _PS0 or _PS3 is implemented, then the other method must also + be implemented. + + -- If a device requires usage or setup of a power resource when on, the ASL + should organize that it is allocated/enabled using the _PS0 method. + + -- Resources allocated or enabled in the _PS0 method should be disabled + or de-allocated in the _PS3 method. + + -- Firmware will leave the resources in a reasonable state before handing + over control to the kernel. + +Such code in _PSx methods will of course be very platform specific. But, +this allows the driver to abstract out the interface for operating the device +and avoid having to read special non-standard values from ACPI tables. Further, +abstracting the use of these resources allows the hardware to change over time +without requiring updates to the driver. + + +Clocks +------ +ACPI makes the assumption that clocks are initialized by the firmware -- +UEFI, in this case -- to some working value before control is handed over +to the kernel. This has implications for devices such as UARTs, or SoC-driven +LCD displays, for example. + +When the kernel boots, the clocks are assumed to be set to reasonable +working values. If for some reason the frequency needs to change -- e.g., +throttling for power management -- the device driver should expect that +process to be abstracted out into some ACPI method that can be invoked +(please see the ACPI specification for further recommendations on standard +methods to be expected). The only exceptions to this are CPU clocks where +CPPC provides a much richer interface than ACPI methods. If the clocks +are not set, there is no direct way for Linux to control them. + +If an SoC vendor wants to provide fine-grained control of the system clocks, +they could do so by providing ACPI methods that could be invoked by Linux +drivers. However, this is NOT recommended and Linux drivers should NOT use +such methods, even if they are provided. Such methods are not currently +standardized in the ACPI specification, and using them could tie a kernel +to a very specific SoC, or tie an SoC to a very specific version of the +kernel, both of which we are trying to avoid. + + +Driver Recommendations +---------------------- +DO NOT remove any DT handling when adding ACPI support for a driver. The +same device may be used on many different systems. + +DO try to structure the driver so that it is data-driven. That is, set up +a struct containing internal per-device state based on defaults and whatever +else must be discovered by the driver probe function. Then, have the rest +of the driver operate off of the contents of that struct. Doing so should +allow most divergence between ACPI and DT functionality to be kept local to +the probe function instead of being scattered throughout the driver. For +example: + +static int device_probe_dt(struct platform_device *pdev) +{ + /* DT specific functionality */ + ... +} + +static int device_probe_acpi(struct platform_device *pdev) +{ + /* ACPI specific functionality */ + ... +} + +static int device_probe(struct platform_device *pdev) +{ + ... + struct device_node node = pdev->dev.of_node; + ... + + if (node) + ret = device_probe_dt(pdev); + else if (ACPI_HANDLE(&pdev->dev)) + ret = device_probe_acpi(pdev); + else + /* other initialization */ + ... + /* Continue with any generic probe operations */ + ... +} + +DO keep the MODULE_DEVICE_TABLE entries together in the driver to make it +clear the different names the driver is probed for, both from DT and from +ACPI: + +static struct of_device_id virtio_mmio_match[] = { + { .compatible = "virtio,mmio", }, + { } +}; +MODULE_DEVICE_TABLE(of, virtio_mmio_match); + +static const struct acpi_device_id virtio_mmio_acpi_match[] = { + { "LNRO0005", }, + { } +}; +MODULE_DEVICE_TABLE(acpi, virtio_mmio_acpi_match); + + +ASWG +---- +The ACPI specification changes regularly. During the year 2014, for instance, +version 5.1 was released and version 6.0 substantially completed, with most of +the changes being driven by ARM-specific requirements. Proposed changes are +presented and discussed in the ASWG (ACPI Specification Working Group) which +is a part of the UEFI Forum. + +Participation in this group is open to all UEFI members. Please see +http://www.uefi.org/workinggroup for details on group membership. + +It is the intent of the ARMv8 ACPI kernel code to follow the ACPI specification +as closely as possible, and to only implement functionality that complies with +the released standards from UEFI ASWG. As a practical matter, there will be +vendors that provide bad ACPI tables or violate the standards in some way. +If this is because of errors, quirks and fixups may be necessary, but will +be avoided if possible. If there are features missing from ACPI that preclude +it from being used on a platform, ECRs (Engineering Change Requests) should be +submitted to ASWG and go through the normal approval process; for those that +are not UEFI members, many other members of the Linux community are and would +likely be willing to assist in submitting ECRs. + + +Linux Code +---------- +Individual items specific to Linux on ARM, contained in the the Linux +source code, are in the list that follows: + +ACPI_OS_NAME This macro defines the string to be returned when + an ACPI method invokes the _OS method. On ARM64 + systems, this macro will be "Linux" by default. + The command line parameter acpi_os= + can be used to set it to some other value. The + default value for other architectures is "Microsoft + Windows NT", for example. + +ACPI Objects +------------ +Detailed expectations for ACPI tables and object are listed in the file +Documentation/arm64/acpi_object_usage.txt. + + +References +---------- +[0] http://silver.arm.com -- document ARM-DEN-0029, or newer + "Server Base System Architecture", version 2.3, dated 27 Mar 2014 + +[1] http://infocenter.arm.com/help/topic/com.arm.doc.den0044a/Server_Base_Boot_Requirements.pdf + Document ARM-DEN-0044A, or newer: "Server Base Boot Requirements, System + Software on ARM Platforms", dated 16 Aug 2014 + +[2] http://www.secretlab.ca/archives/151, 10 Jan 2015, Copyright (c) 2015, + Linaro Ltd., written by Grant Likely. A copy of the verbatim text (apart + from formatting) is also in Documentation/arm64/why_use_acpi.txt. + +[3] AMD ACPI for Seattle platform documentation: + http://amd-dev.wpengine.netdna-cdn.com/wordpress/media/2012/10/Seattle_ACPI_Guide.pdf + +[4] http://www.uefi.org/acpi -- please see the link for the "ACPI _DSD Device + Property Registry Instructions" + +[5] http://www.uefi.org/acpi -- please see the link for the "_DSD (Device + Specific Data) Implementation Guide" + +[6] Kernel code for the unified device property interface can be found in + include/linux/property.h and drivers/base/property.c. + + +Authors +------- +Al Stone +Graeme Gregory +Hanjun Guo + +Grant Likely , for the "Why ACPI on ARM?" section diff --git a/Documentation/devicetree/bindings/arc/pct.txt b/Documentation/devicetree/bindings/arc/pct.txt new file mode 100644 index 000000000000..7b9588444f20 --- /dev/null +++ b/Documentation/devicetree/bindings/arc/pct.txt @@ -0,0 +1,20 @@ +* ARC Performance Counters + +The ARC700 can be configured with a pipeline performance monitor for counting +CPU and cache events like cache misses and hits. Like conventional PCT there +are 100+ hardware conditions dynamically mapped to upto 32 counters + +Note that: + * The ARC 700 PCT does not support interrupts; although HW events may be + counted, the HW events themselves cannot serve as a trigger for a sample. + +Required properties: + +- compatible : should contain + "snps,arc700-pct" + +Example: + +pmu { + compatible = "snps,arc700-pct"; +}; diff --git a/Documentation/devicetree/bindings/arc/pmu.txt b/Documentation/devicetree/bindings/arc/pmu.txt deleted file mode 100644 index 49d517340de3..000000000000 --- a/Documentation/devicetree/bindings/arc/pmu.txt +++ /dev/null @@ -1,24 +0,0 @@ -* ARC Performance Monitor Unit - -The ARC 700 can be configured with a pipeline performance monitor for counting -CPU and cache events like cache misses and hits. - -Note that: - * ARC 700 refers to a family of ARC processor cores; - - There is only one type of PMU available for the whole family; - - The PMU may support different sets of events; supported events are probed - at boot time, as required by the reference manual. - - * The ARC 700 PMU does not support interrupts; although HW events may be - counted, the HW events themselves cannot serve as a trigger for a sample. - -Required properties: - -- compatible : should contain - "snps,arc700-pmu" - -Example: - -pmu { - compatible = "snps,arc700-pmu"; -}; diff --git a/Documentation/devicetree/bindings/arm/al,alpine.txt b/Documentation/devicetree/bindings/arm/al,alpine.txt new file mode 100644 index 000000000000..f404a4f9b165 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/al,alpine.txt @@ -0,0 +1,88 @@ +Annapurna Labs Alpine Platform Device Tree Bindings +--------------------------------------------------------------- + +Boards in the Alpine family shall have the following properties: + +* Required root node properties: +compatible: must contain "al,alpine" + +* Example: + +/ { + model = "Annapurna Labs Alpine Dev Board"; + compatible = "al,alpine"; + + ... +} + +* CPU node: + +The Alpine platform includes cortex-a15 cores. +enable-method: must be "al,alpine-smp" to allow smp [1] + +Example: + +cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "al,alpine-smp"; + + cpu@0 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <0>; + }; + + cpu@1 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <1>; + }; + + cpu@2 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <2>; + }; + + cpu@3 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <3>; + }; +}; + + +* Alpine CPU resume registers + +The CPU resume register are used to define required resume address after +reset. + +Properties: +- compatible : Should contain "al,alpine-cpu-resume". +- reg : Offset and length of the register set for the device + +Example: + +cpu_resume { + compatible = "al,alpine-cpu-resume"; + reg = <0xfbff5ed0 0x30>; +}; + +* Alpine System-Fabric Service Registers + +The System-Fabric Service Registers allow various operation on CPU and +system fabric, like powering CPUs off. + +Properties: +- compatible : Should contain "al,alpine-sysfabric-service" and "syscon". +- reg : Offset and length of the register set for the device + +Example: + +nb_service { + compatible = "al,alpine-sysfabric-service", "syscon"; + reg = <0xfb070000 0x10000>; +}; + +[1] arm/cpu-enable-method/al,alpine-smp diff --git a/Documentation/devicetree/bindings/arm/altera.txt b/Documentation/devicetree/bindings/arm/altera.txt new file mode 100644 index 000000000000..558735aacca8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/altera.txt @@ -0,0 +1,14 @@ +Altera's SoCFPGA platform device tree bindings +--------------------------------------------- + +Boards with Cyclone 5 SoC: +Required root node properties: +compatible = "altr,socfpga-cyclone5", "altr,socfpga"; + +Boards with Arria 5 SoC: +Required root node properties: +compatible = "altr,socfpga-arria5", "altr,socfpga"; + +Boards with Arria 10 SoC: +Required root node properties: +compatible = "altr,socfpga-arria10", "altr,socfpga"; diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 8fe815046140..973884a1bacf 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -8,3 +8,7 @@ Boards with the Amlogic Meson6 SoC shall have the following properties: Boards with the Amlogic Meson8 SoC shall have the following properties: Required root node property: compatible: "amlogic,meson8"; + +Board compatible values: + - "geniatech,atv1200" + - "minix,neo-x8" diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt index 256b4d8bab7b..e774128935d5 100644 --- a/Documentation/devicetree/bindings/arm/arch_timer.txt +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt @@ -17,7 +17,10 @@ to deliver its interrupts via SPIs. - interrupts : Interrupt list for secure, non-secure, virtual and hypervisor timers, in that order. -- clock-frequency : The frequency of the main counter, in Hz. Optional. +- clock-frequency : The frequency of the main counter, in Hz. Should be present + only where necessary to work around broken firmware which does not configure + CNTFRQ on all CPUs to a uniform correct value. Use of this property is + strongly discouraged; fix your firmware unless absolutely impossible. - always-on : a boolean property. If present, the timer is powered through an always-on power domain, therefore it never loses context. @@ -46,7 +49,8 @@ Example: - compatible : Should at least contain "arm,armv7-timer-mem". -- clock-frequency : The frequency of the main counter, in Hz. Optional. +- clock-frequency : The frequency of the main counter, in Hz. Should be present + only when firmware has not configured the MMIO CNTFRQ registers. - reg : The control frame base address. diff --git a/Documentation/devicetree/bindings/arm/armada-39x.txt b/Documentation/devicetree/bindings/arm/armada-39x.txt new file mode 100644 index 000000000000..53d4ff9ea8ad --- /dev/null +++ b/Documentation/devicetree/bindings/arm/armada-39x.txt @@ -0,0 +1,20 @@ +Marvell Armada 39x Platforms Device Tree Bindings +------------------------------------------------- + +Boards with a SoC of the Marvell Armada 39x family shall have the +following property: + +Required root node property: + + - compatible: must contain "marvell,armada390" + +In addition, boards using the Marvell Armada 398 SoC shall have the +following property before the previous one: + +Required root node property: + +compatible: must contain "marvell,armada398" + +Example: + +compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390"; diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index ad319f84f560..2e99b5b57350 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -46,10 +46,12 @@ PIT Timer required properties: shared across all System Controller members. System Timer (ST) required properties: -- compatible: Should be "atmel,at91rm9200-st" +- compatible: Should be "atmel,at91rm9200-st", "syscon", "simple-mfd" - reg: Should contain registers location and length - interrupts: Should contain interrupt for the ST which is the IRQ line shared across all System Controller members. +Its subnodes can be: +- watchdog: compatible should be "atmel,at91rm9200-wdt" TC/TCLIB Timer required properties: - compatible: Should be "atmel,-tcb". diff --git a/Documentation/devicetree/bindings/arm/cci.txt b/Documentation/devicetree/bindings/arm/cci.txt index f28d82bbbc56..3c5c631328d3 100644 --- a/Documentation/devicetree/bindings/arm/cci.txt +++ b/Documentation/devicetree/bindings/arm/cci.txt @@ -94,8 +94,11 @@ specific to ARM. - compatible Usage: required Value type: - Definition: must be "arm,cci-400-pmu" - + Definition: Must contain one of: + "arm,cci-400-pmu,r0" + "arm,cci-400-pmu,r1" + "arm,cci-400-pmu" - DEPRECATED, permitted only where OS has + secure acces to CCI registers - reg: Usage: required Value type: Integer cells. A register entry, expressed diff --git a/Documentation/devicetree/bindings/arm/coresight.txt b/Documentation/devicetree/bindings/arm/coresight.txt index a3089359aaa6..88602b75418e 100644 --- a/Documentation/devicetree/bindings/arm/coresight.txt +++ b/Documentation/devicetree/bindings/arm/coresight.txt @@ -61,7 +61,6 @@ Example: compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0 0x20010000 0 0x1000>; - coresight-default-sink; clocks = <&oscclk6a>; clock-names = "apb_pclk"; port { diff --git a/Documentation/devicetree/bindings/arm/cpu-enable-method/al,alpine-smp b/Documentation/devicetree/bindings/arm/cpu-enable-method/al,alpine-smp new file mode 100644 index 000000000000..c2e0cc5e4cfd --- /dev/null +++ b/Documentation/devicetree/bindings/arm/cpu-enable-method/al,alpine-smp @@ -0,0 +1,52 @@ +======================================================== +Secondary CPU enable-method "al,alpine-smp" binding +======================================================== + +This document describes the "al,alpine-smp" method for +enabling secondary CPUs. To apply to all CPUs, a single +"al,alpine-smp" enable method should be defined in the +"cpus" node. + +Enable method name: "al,alpine-smp" +Compatible machines: "al,alpine" +Compatible CPUs: "arm,cortex-a15" +Related properties: (none) + +Note: +This enable method requires valid nodes compatible with +"al,alpine-cpu-resume" and "al,alpine-nb-service"[1]. + +Example: + +cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "al,alpine-smp"; + + cpu@0 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <0>; + }; + + cpu@1 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <1>; + }; + + cpu@2 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <2>; + }; + + cpu@3 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <3>; + }; +}; + +-- +[1] arm/al,alpine.txt diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 8b9e0a95de31..6aa331d11c5e 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -192,6 +192,7 @@ nodes to be present and contain the properties described below. "brcm,brahma-b15" "marvell,armada-375-smp" "marvell,armada-380-smp" + "marvell,armada-390-smp" "marvell,armada-xp-smp" "qcom,gcc-msm8660" "qcom,kpss-acc-v1" diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt index 1e097037349c..5da38c5ed476 100644 --- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -22,6 +22,9 @@ Optional Properties: - pclkN, clkN: Pairs of parent of input clock and input clock to the devices in this power domain. Maximum of 4 pairs (N = 0 to 3) are supported currently. + - asbN: Clocks required by asynchronous bridges (ASB) present in + the power domain. These clock should be enabled during power + domain on/off operations. - power-domains: phandle pointing to the parent power domain, for more details see Documentation/devicetree/bindings/power/power_domain.txt diff --git a/Documentation/devicetree/bindings/arm/geniatech.txt b/Documentation/devicetree/bindings/arm/geniatech.txt deleted file mode 100644 index 74ccba40b73b..000000000000 --- a/Documentation/devicetree/bindings/arm/geniatech.txt +++ /dev/null @@ -1,5 +0,0 @@ -Geniatech platforms device tree bindings -------------------------------------------- - -Geniatech ATV1200 - - compatible = "geniatech,atv1200" diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt index 1e0d21201d3a..2da059a4790c 100644 --- a/Documentation/devicetree/bindings/arm/gic.txt +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -18,6 +18,8 @@ Main node required properties: "arm,arm11mp-gic" "brcm,brahma-b15-gic" "arm,arm1176jzf-devchip-gic" + "qcom,msm-8660-qgic" + "qcom,msm-qgic2" - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Specifies the number of cells needed to encode an interrupt source. The type shall be a and the value shall be 3. diff --git a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt index 925ecbf6e7b7..4f40ff3fee4b 100644 --- a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt +++ b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt @@ -42,6 +42,7 @@ board. Currently known boards are: "lacie,cloudbox" "lacie,inetspace_v2" "lacie,laplug" +"lacie,nas2big" "lacie,netspace_lite_v2" "lacie,netspace_max_v2" "lacie,netspace_mini_v2" diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt b/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt new file mode 100644 index 000000000000..06df04cc827a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt @@ -0,0 +1,84 @@ +QCOM Idle States for cpuidle driver + +ARM provides idle-state node to define the cpuidle states, as defined in [1]. +cpuidle-qcom is the cpuidle driver for Qualcomm SoCs and uses these idle +states. Idle states have different enter/exit latency and residency values. +The idle states supported by the QCOM SoC are defined as - + + * Standby + * Retention + * Standalone Power Collapse (Standalone PC or SPC) + * Power Collapse (PC) + +Standby: Standby does a little more in addition to architectural clock gating. +When the WFI instruction is executed the ARM core would gate its internal +clocks. In addition to gating the clocks, QCOM cpus use this instruction as a +trigger to execute the SPM state machine. The SPM state machine waits for the +interrupt to trigger the core back in to active. This triggers the cache +hierarchy to enter standby states, when all cpus are idle. An interrupt brings +the SPM state machine out of its wait, the next step is to ensure that the +cache hierarchy is also out of standby, and then the cpu is allowed to resume +execution. This state is defined as a generic ARM WFI state by the ARM cpuidle +driver and is not defined in the DT. The SPM state machine should be +configured to execute this state by default and after executing every other +state below. + +Retention: Retention is a low power state where the core is clock gated and +the memory and the registers associated with the core are retained. The +voltage may be reduced to the minimum value needed to keep the processor +registers active. The SPM should be configured to execute the retention +sequence and would wait for interrupt, before restoring the cpu to execution +state. Retention may have a slightly higher latency than Standby. + +Standalone PC: A cpu can power down and warmboot if there is a sufficient time +between the time it enters idle and the next known wake up. SPC mode is used +to indicate a core entering a power down state without consulting any other +cpu or the system resources. This helps save power only on that core. The SPM +sequence for this idle state is programmed to power down the supply to the +core, wait for the interrupt, restore power to the core, and ensure the +system state including cache hierarchy is ready before allowing core to +resume. Applying power and resetting the core causes the core to warmboot +back into Elevation Level (EL) which trampolines the control back to the +kernel. Entering a power down state for the cpu, needs to be done by trapping +into a EL. Failing to do so, would result in a crash enforced by the warm boot +code in the EL for the SoC. On SoCs with write-back L1 cache, the cache has to +be flushed in s/w, before powering down the core. + +Power Collapse: This state is similar to the SPC mode, but distinguishes +itself in that the cpu acknowledges and permits the SoC to enter deeper sleep +modes. In a hierarchical power domain SoC, this means L2 and other caches can +be flushed, system bus, clocks - lowered, and SoC main XO clock gated and +voltages reduced, provided all cpus enter this state. Since the span of low +power modes possible at this state is vast, the exit latency and the residency +of this low power mode would be considered high even though at a cpu level, +this essentially is cpu power down. The SPM in this state also may handshake +with the Resource power manager (RPM) processor in the SoC to indicate a +complete application processor subsystem shut down. + +The idle-state for QCOM SoCs are distinguished by the compatible property of +the idle-states device node. + +The devicetree representation of the idle state should be - + +Required properties: + +- compatible: Must be one of - + "qcom,idle-state-ret", + "qcom,idle-state-spc", + "qcom,idle-state-pc", + and "arm,idle-state". + +Other required and optional properties are specified in [1]. + +Example: + + idle-states { + CPU_SPC: spc { + compatible = "qcom,idle-state-spc", "arm,idle-state"; + entry-latency-us = <150>; + exit-latency-us = <200>; + min-residency-us = <2000>; + }; + }; + +[1]. Documentation/devicetree/bindings/arm/idle-states.txt diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt index 1505fb8e131a..ae4afc6dcfe0 100644 --- a/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt +++ b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt @@ -2,22 +2,31 @@ SPM AVS Wrapper 2 (SAW2) The SAW2 is a wrapper around the Subsystem Power Manager (SPM) and the Adaptive Voltage Scaling (AVS) hardware. The SPM is a programmable -micro-controller that transitions a piece of hardware (like a processor or +power-controller that transitions a piece of hardware (like a processor or subsystem) into and out of low power modes via a direct connection to the PMIC. It can also be wired up to interact with other processors in the system, notifying them when a low power state is entered or exited. +Multiple revisions of the SAW hardware are supported using these Device Nodes. +SAW2 revisions differ in the register offset and configuration data. Also, the +same revision of the SAW in different SoCs may have different configuration +data due the the differences in hardware capabilities. Hence the SoC name, the +version of the SAW hardware in that SoC and the distinction between cpu (big +or Little) or cache, may be needed to uniquely identify the SAW register +configuration and initialization data. The compatible string is used to +indicate this parameter. + PROPERTIES - compatible: Usage: required Value type: - Definition: shall contain "qcom,saw2". A more specific value should be - one of: - "qcom,saw2-v1" - "qcom,saw2-v1.1" - "qcom,saw2-v2" - "qcom,saw2-v2.1" + Definition: Must have + "qcom,saw2" + A more specific value could be one of: + "qcom,apq8064-saw2-v1.1-cpu" + "qcom,msm8974-saw2-v2.1-cpu" + "qcom,apq8084-saw2-v2.1-cpu" - reg: Usage: required @@ -26,10 +35,23 @@ PROPERTIES the register region. An optional second element specifies the base address and size of the alias register region. +- regulator: + Usage: optional + Value type: boolean + Definition: Indicates that this SPM device acts as a regulator device + device for the core (CPU or Cache) the SPM is attached + to. -Example: +Example 1: - regulator@2099000 { + power-controller@2099000 { compatible = "qcom,saw2"; reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + +Example 2: + saw0: power-controller@f9089000 { + compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2"; + reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/arm/msm/timer.txt b/Documentation/devicetree/bindings/arm/msm/timer.txt index 74607b6c1117..5e10c345548f 100644 --- a/Documentation/devicetree/bindings/arm/msm/timer.txt +++ b/Documentation/devicetree/bindings/arm/msm/timer.txt @@ -9,11 +9,17 @@ Properties: "qcom,scss-timer" - scorpion subsystem - interrupts : Interrupts for the debug timer, the first general purpose - timer, and optionally a second general purpose timer in that - order. + timer, and optionally a second general purpose timer, and + optionally as well, 2 watchdog interrupts, in that order. - reg : Specifies the base address of the timer registers. +- clocks: Reference to the parent clocks, one per output clock. The parents + must appear in the same order as the clock names. + +- clock-names: The name of the clocks as free-form strings. They should be in + the same order as the clocks. + - clock-frequency : The frequency of the debug timer and the general purpose timer(s) in Hz in that order. @@ -29,9 +35,13 @@ Example: compatible = "qcom,scss-timer", "qcom,msm-timer"; interrupts = <1 1 0x301>, <1 2 0x301>, - <1 3 0x301>; + <1 3 0x301>, + <1 4 0x301>, + <1 5 0x301>; reg = <0x0200a000 0x100>; clock-frequency = <19200000>, <32768>; + clocks = <&sleep_clk>; + clock-names = "sleep"; cpu-offset = <0x40000>; }; diff --git a/Documentation/devicetree/bindings/arm/omap/ctrl.txt b/Documentation/devicetree/bindings/arm/omap/ctrl.txt new file mode 100644 index 000000000000..3a4e5901ce31 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/ctrl.txt @@ -0,0 +1,79 @@ +OMAP Control Module bindings + +Control Module contains miscellaneous features under it based on SoC type. +Pincontrol is one common feature, and it has a specialized support +described in [1]. Typically some clock nodes are also under control module. +Syscon is used to share register level access to drivers external to +control module driver itself. + +See [2] for documentation about clock/clockdomain nodes. + +[1] Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt +[2] Documentation/devicetree/bindings/clock/ti/* + +Required properties: +- compatible: Must be one of: + "ti,am3-scm" + "ti,am4-scm" + "ti,dm814-scrm" + "ti,dm816-scrm" + "ti,omap2-scm" + "ti,omap3-scm" + "ti,omap4-scm-core" + "ti,omap4-scm-padconf-core" + "ti,omap5-scm-core" + "ti,omap5-scm-padconf-core" + "ti,dra7-scm-core" +- reg: Contains Control Module register address range + (base address and length) + +Optional properties: +- clocks: clocks for this module +- clockdomains: clockdomains for this module + +Examples: + +scm: scm@2000 { + compatible = "ti,omap3-scm", "simple-bus"; + reg = <0x2000 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2000 0x2000>; + + omap3_pmx_core: pinmux@30 { + compatible = "ti,omap3-padconf", + "pinctrl-single"; + reg = <0x30 0x230>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0xff1f>; + }; + + scm_conf: scm_conf@270 { + compatible = "syscon"; + reg = <0x270 0x330>; + #address-cells = <1>; + #size-cells = <1>; + + scm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + scm_clockdomains: clockdomains { + }; +} + +&scm_clocks { + mcbsp5_mux_fck: mcbsp5_mux_fck { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&core_96m_fck>, <&mcbsp_clks>; + ti,bit-shift = <4>; + reg = <0x02d8>; + }; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt index 974624ea68f6..161448da959d 100644 --- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt +++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt @@ -6,6 +6,7 @@ provided by Arteris. Required properties: - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family Should be "ti,omap4-l3-noc" for OMAP4 family + Should be "ti,omap5-l3-noc" for OMAP5 family Should be "ti,dra7-l3-noc" for DRA7 family Should be "ti,am4372-l3-noc" for AM43 family - reg: Contains L3 register address range for each noc domain. diff --git a/Documentation/devicetree/bindings/arm/omap/l4.txt b/Documentation/devicetree/bindings/arm/omap/l4.txt new file mode 100644 index 000000000000..b4f8a16e7e3b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/l4.txt @@ -0,0 +1,26 @@ +L4 interconnect bindings + +These bindings describe the OMAP SoCs L4 interconnect bus. + +Required properties: +- compatible : Should be "ti,omap2-l4" for OMAP2 family l4 core bus + Should be "ti,omap2-l4-wkup" for OMAP2 family l4 wkup bus + Should be "ti,omap3-l4-core" for OMAP3 family l4 core bus + Should be "ti,omap4-l4-cfg" for OMAP4 family l4 cfg bus + Should be "ti,omap4-l4-wkup" for OMAP4 family l4 wkup bus + Should be "ti,omap5-l4-cfg" for OMAP5 family l4 cfg bus + Should be "ti,omap5-l4-wkup" for OMAP5 family l4 wkup bus + Should be "ti,dra7-l4-cfg" for DRA7 family l4 cfg bus + Should be "ti,dra7-l4-wkup" for DRA7 family l4 wkup bus + Should be "ti,am3-l4-wkup" for AM33xx family l4 wkup bus + Should be "ti,am4-l4-wkup" for AM43xx family l4 wkup bus +- ranges : contains the IO map range for the bus + +Examples: + +l4: l4@48000000 { + compatible "ti,omap2-l4", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x48000000 0x100000>; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/prcm.txt b/Documentation/devicetree/bindings/arm/omap/prcm.txt index 79074dac684a..3eb6d7afff14 100644 --- a/Documentation/devicetree/bindings/arm/omap/prcm.txt +++ b/Documentation/devicetree/bindings/arm/omap/prcm.txt @@ -10,14 +10,10 @@ documentation about the individual clock/clockdomain nodes. Required properties: - compatible: Must be one of: "ti,am3-prcm" - "ti,am3-scrm" "ti,am4-prcm" - "ti,am4-scrm" "ti,omap2-prcm" - "ti,omap2-scrm" "ti,omap3-prm" "ti,omap3-cm" - "ti,omap3-scrm" "ti,omap4-cm1" "ti,omap4-prm" "ti,omap4-cm2" @@ -29,6 +25,8 @@ Required properties: "ti,dra7-prm" "ti,dra7-cm-core-aon" "ti,dra7-cm-core" + "ti,dm814-prcm" + "ti,dm816-prcm" - reg: Contains PRCM module register address range (base address and length) - clocks: clocks for this module diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 6809e4e51ed2..60d4a1e0a9b5 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -22,3 +22,7 @@ Rockchip platforms device tree bindings - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; or - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288"; + +- ChipSPARK PopMetal-RK3288 board: + Required root node properties: + - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 51147cb5c036..c4f19b2e7dd9 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -7,8 +7,6 @@ SoCs: compatible = "renesas,emev2" - RZ/A1H (R7S72100) compatible = "renesas,r7s72100" - - SH-Mobile AP4 (R8A73720/SH7372) - compatible = "renesas,sh7372" - SH-Mobile AG5 (R8A73A00/SH73A0) compatible = "renesas,sh73a0" - R-Mobile APE6 (R8A73A40) @@ -37,8 +35,6 @@ Boards: compatible = "renesas,alt", "renesas,r8a7794" - APE6-EVM compatible = "renesas,ape6evm", "renesas,r8a73a4" - - APE6-EVM - Reference Device Tree Implementation - compatible = "renesas,ape6evm-reference", "renesas,r8a73a4" - Atmark Techno Armadillo-800 EVA compatible = "renesas,armadillo800eva" - BOCK-W @@ -57,12 +53,8 @@ Boards: compatible = "renesas,kzm9d", "renesas,emev2" - Kyoto Microcomputer Co. KZM-A9-GT compatible = "renesas,kzm9g", "renesas,sh73a0" - - Kyoto Microcomputer Co. KZM-A9-GT - Reference Device Tree Implementation - compatible = "renesas,kzm9g-reference", "renesas,sh73a0" - Lager (RTP0RC7790SEB00010S) compatible = "renesas,lager", "renesas,r8a7790" - - Mackerel (R0P7372LC0016RL, AP4 EVM 2nd) - compatible = "renesas,mackerel" - Marzen compatible = "renesas,marzen", "renesas,r8a7779" diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-actmon.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-actmon.txt new file mode 100644 index 000000000000..ea670a5d7ee3 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-actmon.txt @@ -0,0 +1,32 @@ +NVIDIA Tegra Activity Monitor + +The activity monitor block collects statistics about the behaviour of other +components in the system. This information can be used to derive the rate at +which the external memory needs to be clocked in order to serve all requests +from the monitored clients. + +Required properties: +- compatible: should be "nvidia,tegra-actmon" +- reg: offset and length of the register set for the device +- interrupts: standard interrupt property +- clocks: Must contain a phandle and clock specifier pair for each entry in +clock-names. See ../../clock/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - actmon + - emc +- resets: Must contain an entry for each entry in reset-names. See +../../reset/reset.txt for details. +- reset-names: Must include the following entries: + - actmon + +Example: + actmon@6000c800 { + compatible = "nvidia,tegra124-actmon"; + reg = <0x0 0x6000c800 0x0 0x400>; + interrupts = ; + clocks = <&tegra_car TEGRA124_CLK_ACTMON>, + <&tegra_car TEGRA124_CLK_EMC>; + clock-names = "actmon", "emc"; + resets = <&tegra_car 119>; + reset-names = "actmon"; + }; diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt index 63dd8051521c..18729f6fe1e5 100644 --- a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt +++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt @@ -1,7 +1,8 @@ * OMAP OCP2SCP - ocp interface to scp interface properties: -- compatible : Should be "ti,omap-ocp2scp" +- compatible : Should be "ti,am437x-ocp2scp" for AM437x processor + Should be "ti,omap-ocp2scp" for all others - reg : Address and length of the register set for the device - #address-cells, #size-cells : Must be present if the device has sub-nodes - ranges : the child address space are mapped 1:1 onto the parent address space diff --git a/Documentation/devicetree/bindings/bus/renesas,bsc.txt b/Documentation/devicetree/bindings/bus/renesas,bsc.txt new file mode 100644 index 000000000000..90e947269437 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/renesas,bsc.txt @@ -0,0 +1,46 @@ +Renesas Bus State Controller (BSC) +================================== + +The Renesas Bus State Controller (BSC, sometimes called "LBSC within Bus +Bridge", or "External Bus Interface") can be found in several Renesas ARM SoCs. +It provides an external bus for connecting multiple external devices to the +SoC, driving several chip select lines, for e.g. NOR FLASH, Ethernet and USB. + +While the BSC is a fairly simple memory-mapped bus, it may be part of a PM +domain, and may have a gateable functional clock. +Before a device connected to the BSC can be accessed, the PM domain +containing the BSC must be powered on, and the functional clock +driving the BSC must be enabled. + +The bindings for the BSC extend the bindings for "simple-pm-bus". + + +Required properties + - compatible: Must contain an SoC-specific value, and "renesas,bsc" and + "simple-pm-bus" as fallbacks. + SoC-specific values can be: + "renesas,bsc-r8a73a4" for R-Mobile APE6 (r8a73a4) + "renesas,bsc-sh73a0" for SH-Mobile AG5 (sh73a0) + - #address-cells, #size-cells, ranges: Must describe the mapping between + parent address and child address spaces. + - reg: Must contain the base address and length to access the bus controller. + +Optional properties: + - interrupts: Must contain a reference to the BSC interrupt, if available. + - clocks: Must contain a reference to the functional clock, if available. + - power-domains: Must contain a reference to the PM domain, if available. + + +Example: + + bsc: bus@fec10000 { + compatible = "renesas,bsc-sh73a0", "renesas,bsc", + "simple-pm-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x20000000>; + reg = <0xfec10000 0x400>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&zb_clk>; + power-domains = <&pd_a4s>; + }; diff --git a/Documentation/devicetree/bindings/bus/simple-pm-bus.txt b/Documentation/devicetree/bindings/bus/simple-pm-bus.txt new file mode 100644 index 000000000000..d032237512c2 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/simple-pm-bus.txt @@ -0,0 +1,44 @@ +Simple Power-Managed Bus +======================== + +A Simple Power-Managed Bus is a transparent bus that doesn't need a real +driver, as it's typically initialized by the boot loader. + +However, its bus controller is part of a PM domain, or under the control of a +functional clock. Hence, the bus controller's PM domain and/or clock must be +enabled for child devices connected to the bus (either on-SoC or externally) +to function. + +While "simple-pm-bus" follows the "simple-bus" set of properties, as specified +in ePAPR, it is not an extension of "simple-bus". + + +Required properties: + - compatible: Must contain at least "simple-pm-bus". + Must not contain "simple-bus". + It's recommended to let this be preceded by one or more + vendor-specific compatible values. + - #address-cells, #size-cells, ranges: Must describe the mapping between + parent address and child address spaces. + +Optional platform-specific properties for clock or PM domain control (at least +one of them is required): + - clocks: Must contain a reference to the functional clock(s), + - power-domains: Must contain a reference to the PM domain. +Please refer to the binding documentation for the clock and/or PM domain +providers for more details. + + +Example: + + bsc: bus@fec10000 { + compatible = "renesas,bsc-sh73a0", "renesas,bsc", + "simple-pm-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x20000000>; + reg = <0xfec10000 0x400>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&zb_clk>; + power-domains = <&pd_a4s>; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos3250-clock.txt b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt index f57d9dd9ea85..f1738b88c225 100644 --- a/Documentation/devicetree/bindings/clock/exynos3250-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt @@ -9,6 +9,8 @@ Required Properties: - "samsung,exynos3250-cmu" - controller compatible with Exynos3250 SoC. - "samsung,exynos3250-cmu-dmc" - controller compatible with Exynos3250 SoC for Dynamic Memory Controller domain. + - "samsung,exynos3250-cmu-isp" - ISP block clock controller compatible + with Exynos3250 SOC - reg: physical base address of the controller and length of memory mapped region. @@ -36,6 +38,12 @@ Example 1: Examples of clock controller nodes are listed below. #clock-cells = <1>; }; + cmu_isp: clock-controller@10048000 { + compatible = "samsung,exynos3250-cmu-isp"; + reg = <0x10048000 0x1000>; + #clock-cells = <1>; + }; + Example 2: UART controller node that consumes the clock generated by the clock controller. Refer to the standard clock bindings for information about 'clocks' and 'clock-names' property. diff --git a/Documentation/devicetree/bindings/clock/exynos5433-clock.txt b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt new file mode 100644 index 000000000000..63379b04e052 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt @@ -0,0 +1,462 @@ +* Samsung Exynos5433 CMU (Clock Management Units) + +The Exynos5433 clock controller generates and supplies clock to various +controllers within the Exynos5433 SoC. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,exynos5433-cmu-top" - clock controller compatible for CMU_TOP + which generates clocks for IMEM/FSYS/G3D/GSCL/HEVC/MSCL/G2D/MFC/PERIC/PERIS + domains and bus clocks. + - "samsung,exynos5433-cmu-cpif" - clock controller compatible for CMU_CPIF + which generates clocks for LLI (Low Latency Interface) IP. + - "samsung,exynos5433-cmu-mif" - clock controller compatible for CMU_MIF + which generates clocks for DRAM Memory Controller domain. + - "samsung,exynos5433-cmu-peric" - clock controller compatible for CMU_PERIC + which generates clocks for UART/I2C/SPI/I2S/PCM/SPDIF/PWM/SLIMBUS IPs. + - "samsung,exynos5433-cmu-peris" - clock controller compatible for CMU_PERIS + which generates clocks for PMU/TMU/MCT/WDT/RTC/SECKEY/TZPC IPs. + - "samsung,exynos5433-cmu-fsys" - clock controller compatible for CMU_FSYS + which generates clocks for USB/UFS/SDMMC/TSI/PDMA IPs. + - "samsung,exynos5433-cmu-g2d" - clock controller compatible for CMU_G2D + which generates clocks for G2D/MDMA IPs. + - "samsung,exynos5433-cmu-disp" - clock controller compatible for CMU_DISP + which generates clocks for Display (DECON/HDMI/DSIM/MIXER) IPs. + - "samsung,exynos5433-cmu-aud" - clock controller compatible for CMU_AUD + which generates clocks for Cortex-A5/BUS/AUDIO clocks. + - "samsung,exynos5433-cmu-bus0", "samsung,exynos5433-cmu-bus1" + and "samsung,exynos5433-cmu-bus2" - clock controller compatible for CMU_BUS + which generates global data buses clock and global peripheral buses clock. + - "samsung,exynos5433-cmu-g3d" - clock controller compatible for CMU_G3D + which generates clocks for 3D Graphics Engine IP. + - "samsung,exynos5433-cmu-gscl" - clock controller compatible for CMU_GSCL + which generates clocks for GSCALER IPs. + - "samsung,exynos5433-cmu-apollo"- clock controller compatible for CMU_APOLLO + which generates clocks for Cortex-A53 Quad-core processor. + - "samsung,exynos5433-cmu-atlas" - clock controller compatible for CMU_ATLAS + which generates clocks for Cortex-A57 Quad-core processor, CoreSight and + L2 cache controller. + - "samsung,exynos5433-cmu-mscl" - clock controller compatible for CMU_MSCL + which generates clocks for M2M (Memory to Memory) scaler and JPEG IPs. + - "samsung,exynos5433-cmu-mfc" - clock controller compatible for CMU_MFC + which generates clocks for MFC(Multi-Format Codec) IP. + - "samsung,exynos5433-cmu-hevc" - clock controller compatible for CMU_HEVC + which generates clocks for HEVC(High Efficiency Video Codec) decoder IP. + - "samsung,exynos5433-cmu-isp" - clock controller compatible for CMU_ISP + which generates clocks for FIMC-ISP/DRC/SCLC/DIS/3DNR IPs. + - "samsung,exynos5433-cmu-cam0" - clock controller compatible for CMU_CAM0 + which generates clocks for MIPI_CSIS{0|1}/FIMC_LITE_{A|B|D}/FIMC_3AA{0|1} + IPs. + - "samsung,exynos5433-cmu-cam1" - clock controller compatible for CMU_CAM1 + which generates clocks for Cortex-A5/MIPI_CSIS2/FIMC-LITE_C/FIMC-FD IPs. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +- clocks: list of the clock controller input clock identifiers, + from common clock bindings. Please refer the next section + to find the input clocks for a given controller. + +- clock-names: list of the clock controller input clock names, + as described in clock-bindings.txt. + + Input clocks for top clock controller: + - oscclk + - sclk_mphy_pll + - sclk_mfc_pll + - sclk_bus_pll + + Input clocks for cpif clock controller: + - oscclk + + Input clocks for mif clock controller: + - oscclk + - sclk_mphy_pll + + Input clocks for fsys clock controller: + - oscclk + - sclk_ufs_mphy + - div_aclk_fsys_200 + - sclk_pcie_100_fsys + - sclk_ufsunipro_fsys + - sclk_mmc2_fsys + - sclk_mmc1_fsys + - sclk_mmc0_fsys + - sclk_usbhost30_fsys + - sclk_usbdrd30_fsys + + Input clocks for g2d clock controller: + - oscclk + - aclk_g2d_266 + - aclk_g2d_400 + + Input clocks for disp clock controller: + - oscclk + - sclk_dsim1_disp + - sclk_dsim0_disp + - sclk_dsd_disp + - sclk_decon_tv_eclk_disp + - sclk_decon_vclk_disp + - sclk_decon_eclk_disp + - sclk_decon_tv_vclk_disp + - aclk_disp_333 + + Input clocks for bus0 clock controller: + - aclk_bus0_400 + + Input clocks for bus1 clock controller: + - aclk_bus1_400 + + Input clocks for bus2 clock controller: + - oscclk + - aclk_bus2_400 + + Input clocks for g3d clock controller: + - oscclk + - aclk_g3d_400 + + Input clocks for gscl clock controller: + - oscclk + - aclk_gscl_111 + - aclk_gscl_333 + + Input clocks for apollo clock controller: + - oscclk + - sclk_bus_pll_apollo + + Input clocks for atlas clock controller: + - oscclk + - sclk_bus_pll_atlas + + Input clocks for mscl clock controller: + - oscclk + - sclk_jpeg_mscl + - aclk_mscl_400 + + Input clocks for mfc clock controller: + - oscclk + - aclk_mfc_400 + + Input clocks for hevc clock controller: + - oscclk + - aclk_hevc_400 + + Input clocks for isp clock controller: + - oscclk + - aclk_isp_dis_400 + - aclk_isp_400 + + Input clocks for cam0 clock controller: + - oscclk + - aclk_cam0_333 + - aclk_cam0_400 + - aclk_cam0_552 + + Input clocks for cam1 clock controller: + - oscclk + - sclk_isp_uart_cam1 + - sclk_isp_spi1_cam1 + - sclk_isp_spi0_cam1 + - aclk_cam1_333 + - aclk_cam1_400 + - aclk_cam1_552 + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5433.h header and can be used in device +tree sources. + +Example 1: Examples of 'oscclk' source clock node are listed below. + + xxti: xxti { + compatible = "fixed-clock"; + clock-output-names = "oscclk"; + #clock-cells = <0>; + }; + +Example 2: Examples of clock controller nodes are listed below. + + cmu_top: clock-controller@10030000 { + compatible = "samsung,exynos5433-cmu-top"; + reg = <0x10030000 0x0c04>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_mphy_pll", + "sclk_mfc_pll", + "sclk_bus_pll"; + clocks = <&xxti>, + <&cmu_cpif CLK_SCLK_MPHY_PLL>, + <&cmu_mif CLK_SCLK_MFC_PLL>, + <&cmu_mif CLK_SCLK_BUS_PLL>; + }; + + cmu_cpif: clock-controller@10fc0000 { + compatible = "samsung,exynos5433-cmu-cpif"; + reg = <0x10fc0000 0x0c04>; + #clock-cells = <1>; + + clock-names = "oscclk"; + clocks = <&xxti>; + }; + + cmu_mif: clock-controller@105b0000 { + compatible = "samsung,exynos5433-cmu-mif"; + reg = <0x105b0000 0x100c>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_mphy_pll"; + clocks = <&xxti>, + <&cmu_cpif CLK_SCLK_MPHY_PLL>; + }; + + cmu_peric: clock-controller@14c80000 { + compatible = "samsung,exynos5433-cmu-peric"; + reg = <0x14c80000 0x0b08>; + #clock-cells = <1>; + }; + + cmu_peris: clock-controller@10040000 { + compatible = "samsung,exynos5433-cmu-peris"; + reg = <0x10040000 0x0b20>; + #clock-cells = <1>; + }; + + cmu_fsys: clock-controller@156e0000 { + compatible = "samsung,exynos5433-cmu-fsys"; + reg = <0x156e0000 0x0b04>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_ufs_mphy", + "div_aclk_fsys_200", + "sclk_pcie_100_fsys", + "sclk_ufsunipro_fsys", + "sclk_mmc2_fsys", + "sclk_mmc1_fsys", + "sclk_mmc0_fsys", + "sclk_usbhost30_fsys", + "sclk_usbdrd30_fsys"; + clocks = <&xxti>, + <&cmu_cpif CLK_SCLK_UFS_MPHY>, + <&cmu_top CLK_DIV_ACLK_FSYS_200>, + <&cmu_top CLK_SCLK_PCIE_100_FSYS>, + <&cmu_top CLK_SCLK_UFSUNIPRO_FSYS>, + <&cmu_top CLK_SCLK_MMC2_FSYS>, + <&cmu_top CLK_SCLK_MMC1_FSYS>, + <&cmu_top CLK_SCLK_MMC0_FSYS>, + <&cmu_top CLK_SCLK_USBHOST30_FSYS>, + <&cmu_top CLK_SCLK_USBDRD30_FSYS>; + }; + + cmu_g2d: clock-controller@12460000 { + compatible = "samsung,exynos5433-cmu-g2d"; + reg = <0x12460000 0x0b08>; + #clock-cells = <1>; + + clock-names = "oscclk", + "aclk_g2d_266", + "aclk_g2d_400"; + clocks = <&xxti>, + <&cmu_top CLK_ACLK_G2D_266>, + <&cmu_top CLK_ACLK_G2D_400>; + }; + + cmu_disp: clock-controller@13b90000 { + compatible = "samsung,exynos5433-cmu-disp"; + reg = <0x13b90000 0x0c04>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_dsim1_disp", + "sclk_dsim0_disp", + "sclk_dsd_disp", + "sclk_decon_tv_eclk_disp", + "sclk_decon_vclk_disp", + "sclk_decon_eclk_disp", + "sclk_decon_tv_vclk_disp", + "aclk_disp_333"; + clocks = <&xxti>, + <&cmu_mif CLK_SCLK_DSIM1_DISP>, + <&cmu_mif CLK_SCLK_DSIM0_DISP>, + <&cmu_mif CLK_SCLK_DSD_DISP>, + <&cmu_mif CLK_SCLK_DECON_TV_ECLK_DISP>, + <&cmu_mif CLK_SCLK_DECON_VCLK_DISP>, + <&cmu_mif CLK_SCLK_DECON_ECLK_DISP>, + <&cmu_mif CLK_SCLK_DECON_TV_VCLK_DISP>, + <&cmu_mif CLK_ACLK_DISP_333>; + }; + + cmu_aud: clock-controller@114c0000 { + compatible = "samsung,exynos5433-cmu-aud"; + reg = <0x114c0000 0x0b04>; + #clock-cells = <1>; + }; + + cmu_bus0: clock-controller@13600000 { + compatible = "samsung,exynos5433-cmu-bus0"; + reg = <0x13600000 0x0b04>; + #clock-cells = <1>; + + clock-names = "aclk_bus0_400"; + clocks = <&cmu_top CLK_ACLK_BUS0_400>; + }; + + cmu_bus1: clock-controller@14800000 { + compatible = "samsung,exynos5433-cmu-bus1"; + reg = <0x14800000 0x0b04>; + #clock-cells = <1>; + + clock-names = "aclk_bus1_400"; + clocks = <&cmu_top CLK_ACLK_BUS1_400>; + }; + + cmu_bus2: clock-controller@13400000 { + compatible = "samsung,exynos5433-cmu-bus2"; + reg = <0x13400000 0x0b04>; + #clock-cells = <1>; + + clock-names = "oscclk", "aclk_bus2_400"; + clocks = <&xxti>, <&cmu_mif CLK_ACLK_BUS2_400>; + }; + + cmu_g3d: clock-controller@14aa0000 { + compatible = "samsung,exynos5433-cmu-g3d"; + reg = <0x14aa0000 0x1000>; + #clock-cells = <1>; + + clock-names = "oscclk", "aclk_g3d_400"; + clocks = <&xxti>, <&cmu_top CLK_ACLK_G3D_400>; + }; + + cmu_gscl: clock-controller@13cf0000 { + compatible = "samsung,exynos5433-cmu-gscl"; + reg = <0x13cf0000 0x0b10>; + #clock-cells = <1>; + + clock-names = "oscclk", + "aclk_gscl_111", + "aclk_gscl_333"; + clocks = <&xxti>, + <&cmu_top CLK_ACLK_GSCL_111>, + <&cmu_top CLK_ACLK_GSCL_333>; + }; + + cmu_apollo: clock-controller@11900000 { + compatible = "samsung,exynos5433-cmu-apollo"; + reg = <0x11900000 0x1088>; + #clock-cells = <1>; + + clock-names = "oscclk", "sclk_bus_pll_apollo"; + clocks = <&xxti>, <&cmu_mif CLK_SCLK_BUS_PLL_APOLLO>; + }; + + cmu_atlas: clock-controller@11800000 { + compatible = "samsung,exynos5433-cmu-atlas"; + reg = <0x11800000 0x1088>; + #clock-cells = <1>; + + clock-names = "oscclk", "sclk_bus_pll_atlas"; + clocks = <&xxti>, <&cmu_mif CLK_SCLK_BUS_PLL_ATLAS>; + }; + + cmu_mscl: clock-controller@105d0000 { + compatible = "samsung,exynos5433-cmu-mscl"; + reg = <0x105d0000 0x0b10>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_jpeg_mscl", + "aclk_mscl_400"; + clocks = <&xxti>, + <&cmu_top CLK_SCLK_JPEG_MSCL>, + <&cmu_top CLK_ACLK_MSCL_400>; + }; + + cmu_mfc: clock-controller@15280000 { + compatible = "samsung,exynos5433-cmu-mfc"; + reg = <0x15280000 0x0b08>; + #clock-cells = <1>; + + clock-names = "oscclk", "aclk_mfc_400"; + clocks = <&xxti>, <&cmu_top CLK_ACLK_MFC_400>; + }; + + cmu_hevc: clock-controller@14f80000 { + compatible = "samsung,exynos5433-cmu-hevc"; + reg = <0x14f80000 0x0b08>; + #clock-cells = <1>; + + clock-names = "oscclk", "aclk_hevc_400"; + clocks = <&xxti>, <&cmu_top CLK_ACLK_HEVC_400>; + }; + + cmu_isp: clock-controller@146d0000 { + compatible = "samsung,exynos5433-cmu-isp"; + reg = <0x146d0000 0x0b0c>; + #clock-cells = <1>; + + clock-names = "oscclk", + "aclk_isp_dis_400", + "aclk_isp_400"; + clocks = <&xxti>, + <&cmu_top CLK_ACLK_ISP_DIS_400>, + <&cmu_top CLK_ACLK_ISP_400>; + }; + + cmu_cam0: clock-controller@120d0000 { + compatible = "samsung,exynos5433-cmu-cam0"; + reg = <0x120d0000 0x0b0c>; + #clock-cells = <1>; + + clock-names = "oscclk", + "aclk_cam0_333", + "aclk_cam0_400", + "aclk_cam0_552"; + clocks = <&xxti>, + <&cmu_top CLK_ACLK_CAM0_333>, + <&cmu_top CLK_ACLK_CAM0_400>, + <&cmu_top CLK_ACLK_CAM0_552>; + }; + + cmu_cam1: clock-controller@145d0000 { + compatible = "samsung,exynos5433-cmu-cam1"; + reg = <0x145d0000 0x0b08>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_isp_uart_cam1", + "sclk_isp_spi1_cam1", + "sclk_isp_spi0_cam1", + "aclk_cam1_333", + "aclk_cam1_400", + "aclk_cam1_552"; + clocks = <&xxti>, + <&cmu_top CLK_SCLK_ISP_UART_CAM1>, + <&cmu_top CLK_SCLK_ISP_SPI1_CAM1>, + <&cmu_top CLK_SCLK_ISP_SPI0_CAM1>, + <&cmu_top CLK_ACLK_CAM1_333>, + <&cmu_top CLK_ACLK_CAM1_400>, + <&cmu_top CLK_ACLK_CAM1_552>; + }; + +Example 3: UART controller node that consumes the clock generated by the clock + controller. + + serial_0: serial@14C10000 { + compatible = "samsung,exynos5433-uart"; + reg = <0x14C10000 0x100>; + interrupts = <0 421 0>; + clocks = <&cmu_peric CLK_PCLK_UART0>, + <&cmu_peric CLK_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + pinctrl-names = "default"; + pinctrl-0 = <&uart0_bus>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/fujitsu,mb86s70-crg11.txt b/Documentation/devicetree/bindings/clock/fujitsu,mb86s70-crg11.txt new file mode 100644 index 000000000000..332396265689 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/fujitsu,mb86s70-crg11.txt @@ -0,0 +1,26 @@ +Fujitsu CRG11 clock driver bindings +----------------------------------- + +Required properties : +- compatible : Shall contain "fujitsu,mb86s70-crg11" +- #clock-cells : Shall be 3 {cntrlr domain port} + +The consumer specifies the desired clock pointing to its phandle. + +Example: + + clock: crg11 { + compatible = "fujitsu,mb86s70-crg11"; + #clock-cells = <3>; + }; + + mhu: mhu0@2b1f0000 { + #mbox-cells = <1>; + compatible = "arm,mhu"; + reg = <0 0x2B1F0000 0x1000>; + interrupts = <0 36 4>, /* LP Non-Sec */ + <0 35 4>, /* HP Non-Sec */ + <0 37 4>; /* Secure */ + clocks = <&clock 0 2 1>; /* Cntrlr:0 Domain:2 Port:1 */ + clock-names = "clk"; + }; diff --git a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt index dc5ea5b22da9..670c2af3e931 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt @@ -23,6 +23,14 @@ The following is a list of provided IDs and clock names on Armada 380/385: 2 = l2clk (L2 Cache clock) 3 = ddrclk (DDR clock) +The following is a list of provided IDs and clock names on Armada 39x: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = nbclk (Coherent Fabric clock) + 3 = hclk (SDRAM Controller Internal Clock) + 4 = dclk (SDRAM Interface Clock) + 5 = refclk (Reference Clock) + The following is a list of provided IDs and clock names on Kirkwood and Dove: 0 = tclk (Internal Bus clock) 1 = cpuclk (CPU0 clock) @@ -39,6 +47,7 @@ Required properties: "marvell,armada-370-core-clock" - For Armada 370 SoC core clocks "marvell,armada-375-core-clock" - For Armada 375 SoC core clocks "marvell,armada-380-core-clock" - For Armada 380/385 SoC core clocks + "marvell,armada-390-core-clock" - For Armada 39x SoC core clocks "marvell,armada-xp-core-clock" - For Armada XP SoC core clocks "marvell,dove-core-clock" - for Dove SoC core clocks "marvell,kirkwood-core-clock" - for Kirkwood SoC (except mv88f6180) diff --git a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt index 76477be742b2..31c7c0c1ce8f 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt @@ -1,6 +1,6 @@ * Gated Clock bindings for Marvell EBU SoCs -Marvell Armada 370/375/380/385/XP, Dove and Kirkwood allow some +Marvell Armada 370/375/380/385/39x/XP, Dove and Kirkwood allow some peripheral clocks to be gated to save some power. The clock consumer should specify the desired clock by having the clock ID in its "clocks" phandle cell. The clock ID is directly mapped to the @@ -77,6 +77,18 @@ ID Clock Peripheral 28 xor1 XOR 1 30 sata1 SATA 1 +The following is a list of provided IDs for Armada 39x: +ID Clock Peripheral +----------------------------------- +5 pex1 PCIe 1 +6 pex2 PCIe 2 +7 pex3 PCIe 3 +8 pex0 PCIe 0 +9 usb3h0 USB3 Host 0 +17 sdio SDIO +22 xor0 XOR 0 +28 xor1 XOR 1 + The following is a list of provided IDs for Armada XP: ID Clock Peripheral ----------------------------------- @@ -152,6 +164,7 @@ Required properties: "marvell,armada-370-gating-clock" - for Armada 370 SoC clock gating "marvell,armada-375-gating-clock" - for Armada 375 SoC clock gating "marvell,armada-380-gating-clock" - for Armada 380/385 SoC clock gating + "marvell,armada-390-gating-clock" - for Armada 39x SoC clock gating "marvell,armada-xp-gating-clock" - for Armada XP SoC clock gating "marvell,dove-gating-clock" - for Dove SoC clock gating "marvell,kirkwood-gating-clock" - for Kirkwood SoC clock gating diff --git a/Documentation/devicetree/bindings/clock/pwm-clock.txt b/Documentation/devicetree/bindings/clock/pwm-clock.txt new file mode 100644 index 000000000000..83db876b3b90 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/pwm-clock.txt @@ -0,0 +1,26 @@ +Binding for an external clock signal driven by a PWM pin. + +This binding uses the common clock binding[1] and the common PWM binding[2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/pwm/pwm.txt + +Required properties: +- compatible : shall be "pwm-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- pwms : from common PWM binding; this determines the clock frequency + via the period given in the PWM specifier. + +Optional properties: +- clock-output-names : From common clock binding. +- clock-frequency : Exact output frequency, in case the PWM period + is not exact but was rounded to nanoseconds. + +Example: + clock { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + clock-output-names = "mipi_mclk"; + pwms = <&pwm2 0 40>; /* 1 / 40 ns = 25 MHz */ + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt index aba3d254e037..54c23f34f194 100644 --- a/Documentation/devicetree/bindings/clock/qcom,gcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -8,6 +8,7 @@ Required properties : "qcom,gcc-apq8084" "qcom,gcc-ipq8064" "qcom,gcc-msm8660" + "qcom,gcc-msm8916" "qcom,gcc-msm8960" "qcom,gcc-msm8974" "qcom,gcc-msm8974pro" diff --git a/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt new file mode 100644 index 000000000000..2f3747fdcf1c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt @@ -0,0 +1,25 @@ +* Renesas R8A7778 Clock Pulse Generator (CPG) + +The CPG generates core clocks for the R8A7778. It includes two PLLs and +several fixed ratio dividers + +Required Properties: + + - compatible: Must be "renesas,r8a7778-cpg-clocks" + - reg: Base address and length of the memory resource used by the CPG + - #clock-cells: Must be 1 + - clock-output-names: The names of the clocks. Supported clocks are + "plla", "pllb", "b", "out", "p", "s", and "s1". + + +Example +------- + + cpg_clocks: cpg_clocks@ffc80000 { + compatible = "renesas,r8a7778-cpg-clocks"; + reg = <0xffc80000 0x80>; + #clock-cells = <1>; + clocks = <&extal_clk>; + clock-output-names = "plla", "pllb", "b", + "out", "p", "s", "s1"; + }; diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index 60b44285250d..4fa11af3d378 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -20,6 +20,7 @@ Required properties: "allwinner,sun8i-a23-axi-clk" - for the AXI clock on A23 "allwinner,sun4i-a10-axi-gates-clk" - for the AXI gates "allwinner,sun4i-a10-ahb-clk" - for the AHB clock + "allwinner,sun5i-a13-ahb-clk" - for the AHB clock on A13 "allwinner,sun9i-a80-ahb-clk" - for the AHB bus clocks on A80 "allwinner,sun4i-a10-ahb-gates-clk" - for the AHB gates on A10 "allwinner,sun5i-a13-ahb-gates-clk" - for the AHB gates on A13 @@ -66,6 +67,8 @@ Required properties: "allwinner,sun4i-a10-usb-clk" - for usb gates + resets on A10 / A20 "allwinner,sun5i-a13-usb-clk" - for usb gates + resets on A13 "allwinner,sun6i-a31-usb-clk" - for usb gates + resets on A31 + "allwinner,sun9i-a80-usb-mod-clk" - for usb gates + resets on A80 + "allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80 Required properties for all clocks: - reg : shall be the control register address for the clock. diff --git a/Documentation/devicetree/bindings/common-properties.txt b/Documentation/devicetree/bindings/common-properties.txt new file mode 100644 index 000000000000..3193979b1d05 --- /dev/null +++ b/Documentation/devicetree/bindings/common-properties.txt @@ -0,0 +1,60 @@ +Common properties + +The ePAPR specification does not define any properties related to hardware +byteswapping, but endianness issues show up frequently in porting Linux to +different machine types. This document attempts to provide a consistent +way of handling byteswapping across drivers. + +Optional properties: + - big-endian: Boolean; force big endian register accesses + unconditionally (e.g. ioread32be/iowrite32be). Use this if you + know the peripheral always needs to be accessed in BE mode. + - little-endian: Boolean; force little endian register accesses + unconditionally (e.g. readl/writel). Use this if you know the + peripheral always needs to be accessed in LE mode. + - native-endian: Boolean; always use register accesses matched to the + endianness of the kernel binary (e.g. LE vmlinux -> readl/writel, + BE vmlinux -> ioread32be/iowrite32be). In this case no byteswaps + will ever be performed. Use this if the hardware "self-adjusts" + register endianness based on the CPU's configured endianness. + +If a binding supports these properties, then the binding should also +specify the default behavior if none of these properties are present. +In such cases, little-endian is the preferred default, but it is not +a requirement. The of_device_is_big_endian() and of_fdt_is_big_endian() +helper functions do assume that little-endian is the default, because +most existing (PCI-based) drivers implicitly default to LE by using +readl/writel for MMIO accesses. + +Examples: +Scenario 1 : CPU in LE mode & device in LE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... + native-endian; +}; + +Scenario 2 : CPU in LE mode & device in BE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... + big-endian; +}; + +Scenario 3 : CPU in BE mode & device in BE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... + native-endian; +}; + +Scenario 4 : CPU in BE mode & device in LE mode. +dev: dev@40031000 { + compatible = "name"; + reg = <0x40031000 0x1000>; + ... + little-endian; +}; diff --git a/Documentation/devicetree/bindings/cris/axis.txt b/Documentation/devicetree/bindings/cris/axis.txt new file mode 100644 index 000000000000..d209ca2a47c0 --- /dev/null +++ b/Documentation/devicetree/bindings/cris/axis.txt @@ -0,0 +1,9 @@ +Axis Communications AB +ARTPEC series SoC Device Tree Bindings + + +CRISv32 based SoCs are ETRAX FS and ARTPEC-3: + + - compatible = "axis,crisv32"; + + diff --git a/Documentation/devicetree/bindings/cris/boards.txt b/Documentation/devicetree/bindings/cris/boards.txt new file mode 100644 index 000000000000..533dd273ccf7 --- /dev/null +++ b/Documentation/devicetree/bindings/cris/boards.txt @@ -0,0 +1,8 @@ +Boards based on the CRIS SoCs: + +Required root node properties: + - compatible = should be one or more of the following: + - "axis,dev88" - for Axis devboard 88 with ETRAX FS + +Optional: + diff --git a/Documentation/devicetree/bindings/cris/interrupts.txt b/Documentation/devicetree/bindings/cris/interrupts.txt new file mode 100644 index 000000000000..e8b123b0a5e6 --- /dev/null +++ b/Documentation/devicetree/bindings/cris/interrupts.txt @@ -0,0 +1,23 @@ +* CRISv32 Interrupt Controller + +Interrupt controller for the CRISv32 SoCs. + +Main node required properties: + +- compatible : should be: + "axis,crisv32-intc" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The type shall be a and the value shall be 1. +- reg: physical base address and size of the intc registers map. + +Example: + + intc: interrupt-controller { + compatible = "axis,crisv32-intc"; + reg = <0xb001c000 0x1000>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + diff --git a/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt b/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt new file mode 100644 index 000000000000..d3058768b23d --- /dev/null +++ b/Documentation/devicetree/bindings/dma/apm-xgene-dma.txt @@ -0,0 +1,47 @@ +Applied Micro X-Gene SoC DMA nodes + +DMA nodes are defined to describe on-chip DMA interfaces in +APM X-Gene SoC. + +Required properties for DMA interfaces: +- compatible: Should be "apm,xgene-dma". +- device_type: set to "dma". +- reg: Address and length of the register set for the device. + It contains the information of registers in the following order: + 1st - DMA control and status register address space. + 2nd - Descriptor ring control and status register address space. + 3rd - Descriptor ring command register address space. + 4th - Soc efuse register address space. +- interrupts: DMA has 5 interrupts sources. 1st interrupt is + DMA error reporting interrupt. 2nd, 3rd, 4th and 5th interrupts + are completion interrupts for each DMA channels. +- clocks: Reference to the clock entry. + +Optional properties: +- dma-coherent : Present if dma operations are coherent + +Example: + dmaclk: dmaclk@1f27c000 { + compatible = "apm,xgene-device-clock"; + #clock-cells = <1>; + clocks = <&socplldiv2 0>; + reg = <0x0 0x1f27c000 0x0 0x1000>; + reg-names = "csr-reg"; + clock-output-names = "dmaclk"; + }; + + dma: dma@1f270000 { + compatible = "apm,xgene-storm-dma"; + device_type = "dma"; + reg = <0x0 0x1f270000 0x0 0x10000>, + <0x0 0x1f200000 0x0 0x10000>, + <0x0 0x1b008000 0x0 0x2000>, + <0x0 0x1054a000 0x0 0x100>; + interrupts = <0x0 0x82 0x4>, + <0x0 0xb8 0x4>, + <0x0 0xb9 0x4>, + <0x0 0xba 0x4>, + <0x0 0xbb 0x4>; + dma-coherent; + clocks = <&dmaclk 0>; + }; diff --git a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt index a4873e5e3e36..e30e184f50c7 100644 --- a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt @@ -38,7 +38,7 @@ dma_apbx: dma-apbx@80024000 { 80 81 68 69 70 71 72 73 74 75 76 77>; - interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty", + interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty", "saif0", "saif1", "i2c0", "i2c1", "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx", "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx"; diff --git a/Documentation/devicetree/bindings/dma/jz4780-dma.txt b/Documentation/devicetree/bindings/dma/jz4780-dma.txt new file mode 100644 index 000000000000..f25feee62b15 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/jz4780-dma.txt @@ -0,0 +1,56 @@ +* Ingenic JZ4780 DMA Controller + +Required properties: + +- compatible: Should be "ingenic,jz4780-dma" +- reg: Should contain the DMA controller registers location and length. +- interrupts: Should contain the interrupt specifier of the DMA controller. +- interrupt-parent: Should be the phandle of the interrupt controller that +- clocks: Should contain a clock specifier for the JZ4780 PDMA clock. +- #dma-cells: Must be <2>. Number of integer cells in the dmas property of + DMA clients (see below). + +Optional properties: + +- ingenic,reserved-channels: Bitmask of channels to reserve for devices that + need a specific channel. These channels will only be assigned when explicitly + requested by a client. The primary use for this is channels 0 and 1, which + can be configured to have special behaviour for NAND/BCH when using + programmable firmware. + +Example: + +dma: dma@13420000 { + compatible = "ingenic,jz4780-dma"; + reg = <0x13420000 0x10000>; + + interrupt-parent = <&intc>; + interrupts = <10>; + + clocks = <&cgu JZ4780_CLK_PDMA>; + + #dma-cells = <2>; + + ingenic,reserved-channels = <0x3>; +}; + +DMA clients must use the format described in dma.txt, giving a phandle to the +DMA controller plus the following 2 integer cells: + +1. Request type: The DMA request type for transfers to/from the device on + the allocated channel, as defined in the SoC documentation. + +2. Channel: If set to 0xffffffff, any available channel will be allocated for + the client. Otherwise, the exact channel specified will be used. The channel + should be reserved on the DMA controller using the ingenic,reserved-channels + property. + +Example: + +uart0: serial@10030000 { + ... + dmas = <&dma 0x14 0xffffffff + &dma 0x15 0xffffffff>; + dma-names = "tx", "rx"; + ... +}; diff --git a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt index f8c3311b7153..1c9d48ea4914 100644 --- a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt +++ b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt @@ -4,6 +4,7 @@ Required properties: - compatible: must be one of the following: * "qcom,bam-v1.4.0" for MSM8974, APQ8074 and APQ8084 * "qcom,bam-v1.3.0" for APQ8064, IPQ8064 and MSM8960 + * "qcom,bam-v1.7.0" for MSM8916 - reg: Address range for DMA registers - interrupts: Should contain the one interrupt shared by all channels - #dma-cells: must be <1>, the cell in the dmas property of the client device diff --git a/Documentation/devicetree/bindings/dma/rcar-audmapp.txt b/Documentation/devicetree/bindings/dma/rcar-audmapp.txt deleted file mode 100644 index 61bca509d7b9..000000000000 --- a/Documentation/devicetree/bindings/dma/rcar-audmapp.txt +++ /dev/null @@ -1,29 +0,0 @@ -* R-Car Audio DMAC peri peri Device Tree bindings - -Required properties: -- compatible: should be "renesas,rcar-audmapp" -- #dma-cells: should be <1>, see "dmas" property below - -Example: - audmapp: audio-dma-pp@0xec740000 { - compatible = "renesas,rcar-audmapp"; - #dma-cells = <1>; - - reg = <0 0xec740000 0 0x200>; - }; - - -* DMA client - -Required properties: -- dmas: a list of <[DMA multiplexer phandle] [SRS << 8 | DRS]> pairs. - where SRS/DRS are specified in the SoC manual. - It will be written into PDMACHCR as high 16-bit parts. -- dma-names: a list of DMA channel names, one per "dmas" entry - -Example: - - dmas = <&audmapp 0x2d00 - &audmapp 0x3700>; - dma-names = "src0_ssiu0", - "dvc0_ssiu0"; diff --git a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt new file mode 100644 index 000000000000..040f365954cc --- /dev/null +++ b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt @@ -0,0 +1,37 @@ +* Renesas USB DMA Controller Device Tree bindings + +Required Properties: +- compatible: must contain "renesas,usb-dmac" +- reg: base address and length of the registers block for the DMAC +- interrupts: interrupt specifiers for the DMAC, one for each entry in + interrupt-names. +- interrupt-names: one entry per channel, named "ch%u", where %u is the + channel number ranging from zero to the number of channels minus one. +- clocks: a list of phandle + clock-specifier pairs. +- #dma-cells: must be <1>, the cell specifies the channel number of the DMAC + port connected to the DMA client. +- dma-channels: number of DMA channels + +Example: R8A7790 (R-Car H2) USB-DMACs + + usb_dmac0: dma-controller@e65a0000 { + compatible = "renesas,usb-dmac"; + reg = <0 0xe65a0000 0 0x100>; + interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH + 0 109 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ch0", "ch1"; + clocks = <&mstp3_clks R8A7790_CLK_USBDMAC0>; + #dma-cells = <1>; + dma-channels = <2>; + }; + + usb_dmac1: dma-controller@e65b0000 { + compatible = "renesas,usb-dmac"; + reg = <0 0xe65b0000 0 0x100>; + interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH + 0 110 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ch0", "ch1"; + clocks = <&mstp3_clks R8A7790_CLK_USBDMAC1>; + #dma-cells = <1>; + dma-channels = <2>; + }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt new file mode 100644 index 000000000000..af0b903de293 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt @@ -0,0 +1,18 @@ +USB GPIO Extcon device + +This is a virtual device used to generate USB cable states from the USB ID pin +connected to a GPIO pin. + +Required properties: +- compatible: Should be "linux,extcon-usb-gpio" +- id-gpio: gpio for USB ID pin. See gpio binding. + +Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below: + extcon_usb1 { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>; + } + + &omap_dwc3_1 { + extcon = <&extcon_usb1>; + }; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 003bd77b4595..ad0c4ac916dd 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -77,6 +77,7 @@ nxp,pca9556 Octal SMBus and I2C registered interface nxp,pca9557 8-bit I2C-bus and SMBus I/O port with reset nxp,pcf8563 Real-time clock/calendar nxp,pcf85063 Tiny Real-Time Clock +oki,ml86v7667 OKI ML86V7667 video decoder ovti,ov5642 OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI and Embedded TrueFocus pericom,pt7c4338 Real-time Clock Module plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch diff --git a/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt b/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt index bf52ed4a5067..4ef45636ebde 100644 --- a/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt +++ b/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt @@ -4,7 +4,7 @@ Required properties: - compatible : should be one of: "samsung,s5pv210-jpeg", "samsung,exynos4210-jpeg", - "samsung,exynos3250-jpeg"; + "samsung,exynos3250-jpeg", "samsung,exynos5420-jpeg"; - reg : address and length of the JPEG codec IP register set; - interrupts : specifies the JPEG codec IP interrupt; - clock-names : should contain: diff --git a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt new file mode 100644 index 000000000000..202565313e82 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt @@ -0,0 +1,39 @@ +* Aptina 1/3-Inch WVGA CMOS Digital Image Sensor + +The Aptina MT9V032 is a 1/3-inch CMOS active pixel digital image sensor with +an active array size of 752H x 480V. It is programmable through a simple +two-wire serial interface. + +Required Properties: + +- compatible: value should be either one among the following + (a) "aptina,mt9v022" for MT9V022 color sensor + (b) "aptina,mt9v022m" for MT9V022 monochrome sensor + (c) "aptina,mt9v024" for MT9V024 color sensor + (d) "aptina,mt9v024m" for MT9V024 monochrome sensor + (e) "aptina,mt9v032" for MT9V032 color sensor + (f) "aptina,mt9v032m" for MT9V032 monochrome sensor + (g) "aptina,mt9v034" for MT9V034 color sensor + (h) "aptina,mt9v034m" for MT9V034 monochrome sensor + +Optional Properties: + +- link-frequencies: List of allowed link frequencies in Hz. Each frequency is + expressed as a 64-bit big-endian integer. + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + mt9v032@5c { + compatible = "aptina,mt9v032"; + reg = <0x5c>; + + port { + mt9v032_out: endpoint { + link-frequencies = /bits/ 64 + <13000000 26600000 27000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov2640.txt b/Documentation/devicetree/bindings/media/i2c/ov2640.txt new file mode 100644 index 000000000000..c429b5bdcaa0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov2640.txt @@ -0,0 +1,46 @@ +* Omnivision OV2640 CMOS sensor + +The Omnivision OV2640 sensor support multiple resolutions output, such as +CIF, SVGA, UXGA. It also can support YUV422/420, RGB565/555 or raw RGB +output format. + +Required Properties: +- compatible: should be "ovti,ov2640" +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". + +Optional Properties: +- resetb-gpios: reference to the GPIO connected to the resetb pin, if any. +- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c1: i2c@f0018000 { + ov2640: camera@0x30 { + compatible = "ovti,ov2640"; + reg = <0x30>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck1 &pinctrl_ov2640_pwdn &pinctrl_ov2640_resetb>; + + resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>; + pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>; + + clocks = <&pck1>; + clock-names = "xvclk"; + + assigned-clocks = <&pck1>; + assigned-clock-rates = <25000000>; + + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + bus-width = <8>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov2659.txt b/Documentation/devicetree/bindings/media/i2c/ov2659.txt new file mode 100644 index 000000000000..cabc7d827dfb --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov2659.txt @@ -0,0 +1,38 @@ +* OV2659 1/5-Inch 2Mp SOC Camera + +The Omnivision OV2659 is a 1/5-inch SOC camera, with an active array size of +1632H x 1212V. It is programmable through a SCCB. The OV2659 sensor supports +multiple resolutions output, such as UXGA, SVGA, 720p. It also can support +YUV422, RGB565/555 or raw RGB output formats. + +Required Properties: +- compatible: Must be "ovti,ov2659" +- reg: I2C slave address +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". +- link-frequencies: target pixel clock frequency. + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + ov2659@30 { + compatible = "ovti,ov2659"; + reg = <0x30>; + + clocks = <&clk_ov2659 0>; + clock-names = "xvclk"; + + port { + ov2659_0: endpoint { + remote-endpoint = <&vpfe_ep>; + link-frequencies = /bits/ 64 <70000000>; + }; + }; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/ti,omap3isp.txt b/Documentation/devicetree/bindings/media/ti,omap3isp.txt new file mode 100644 index 000000000000..ac23de855641 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti,omap3isp.txt @@ -0,0 +1,71 @@ +OMAP 3 ISP Device Tree bindings +=============================== + +The DT definitions can be found in include/dt-bindings/media/omap3-isp.h. + +Required properties +=================== + +compatible : must contain "ti,omap3-isp" + +reg : the two registers sets (physical address and length) for the + ISP. The first set contains the core ISP registers up to + the end of the SBL block. The second set contains the + CSI PHYs and receivers registers. +interrupts : the ISP interrupt specifier +iommus : phandle and IOMMU specifier for the IOMMU that serves the ISP +syscon : the phandle and register offset to the Complex I/O or CSI-PHY + register +ti,phy-type : 0 -- OMAP3ISP_PHY_TYPE_COMPLEX_IO (e.g. 3430) + 1 -- OMAP3ISP_PHY_TYPE_CSIPHY (e.g. 3630) +#clock-cells : Must be 1 --- the ISP provides two external clocks, + cam_xclka and cam_xclkb, at indices 0 and 1, + respectively. Please find more information on common + clock bindings in ../clock/clock-bindings.txt. + +Port nodes (optional) +--------------------- + +More documentation on these bindings is available in +video-interfaces.txt in the same directory. + +reg : The interface: + 0 - parallel (CCDC) + 1 - CSIPHY1 -- CSI2C / CCP2B on 3630; + CSI1 -- CSIb on 3430 + 2 - CSIPHY2 -- CSI2A / CCP2B on 3630; + CSI2 -- CSIa on 3430 + +Optional properties +=================== + +vdd-csiphy1-supply : voltage supply of the CSI-2 PHY 1 +vdd-csiphy2-supply : voltage supply of the CSI-2 PHY 2 + +Endpoint nodes +-------------- + +lane-polarities : lane polarity (required on CSI-2) + 0 -- not inverted; 1 -- inverted +data-lanes : an array of data lanes from 1 to 3. The length can + be either 1 or 2. (required on CSI-2) +clock-lanes : the clock lane (from 1 to 3). (required on CSI-2) + + +Example +======= + + isp@480bc000 { + compatible = "ti,omap3-isp"; + reg = <0x480bc000 0x12fc + 0x480bd800 0x0600>; + interrupts = <24>; + iommus = <&mmu_isp>; + syscon = <&scm_conf 0x2f0>; + ti,phy-type = ; + #clock-cells = <1>; + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt index 571b4c60665f..9cd2a369125d 100644 --- a/Documentation/devicetree/bindings/media/video-interfaces.txt +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -106,6 +106,12 @@ Optional endpoint properties - link-frequencies: Allowed data bus frequencies. For MIPI CSI-2, for instance, this is the actual frequency of the bus, not bits per clock per lane value. An array of 64-bit unsigned integers. +- lane-polarities: an array of polarities of the lanes starting from the clock + lane and followed by the data lanes in the same order as in data-lanes. + Valid values are 0 (normal) and 1 (inverted). The length of the array + should be the combined length of data-lanes and clock-lanes properties. + If the lane-polarities property is omitted, the value must be interpreted + as 0 (normal). This property is valid for serial busses only. Example diff --git a/Documentation/devicetree/bindings/media/xilinx/video.txt b/Documentation/devicetree/bindings/media/xilinx/video.txt new file mode 100644 index 000000000000..cbd46fa0988f --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/video.txt @@ -0,0 +1,35 @@ +DT bindings for Xilinx video IP cores +------------------------------------- + +Xilinx video IP cores process video streams by acting as video sinks and/or +sources. They are connected by links through their input and output ports, +creating a video pipeline. + +Each video IP core is represented by an AMBA bus child node in the device +tree using bindings documented in this directory. Connections between the IP +cores are represented as defined in ../video-interfaces.txt. + +The whole pipeline is represented by an AMBA bus child node in the device +tree using bindings documented in ./xlnx,video.txt. + +Common properties +----------------- + +The following properties are common to all Xilinx video IP cores. + +- xlnx,video-format: This property represents a video format transmitted on an + AXI bus between video IP cores, using its VF code as defined in "AXI4-Stream + Video IP and System Design Guide" [UG934]. How the format relates to the IP + core is decribed in the IP core bindings documentation. + +- xlnx,video-width: This property qualifies the video format with the sample + width expressed as a number of bits per pixel component. All components must + use the same width. + +- xlnx,cfa-pattern: When the video format is set to Mono/Sensor, this property + describes the sensor's color filter array pattern. Supported values are + "bggr", "gbrg", "grbg", "rggb" and "mono". If not specified, the pattern + defaults to "mono". + + +[UG934] http://www.xilinx.com/support/documentation/ip_documentation/axi_videoip/v1_0/ug934_axi_videoIP.pdf diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt new file mode 100644 index 000000000000..2aed3b4a6cf1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt @@ -0,0 +1,33 @@ +Xilinx Video Timing Controller (VTC) +------------------------------------ + +The Video Timing Controller is a general purpose video timing generator and +detector. + +Required properties: + + - compatible: Must be "xlnx,v-tc-6.1". + + - reg: Physical base address and length of the registers set for the device. + + - clocks: Must contain a clock specifier for the VTC core and timing + interfaces clock. + +Optional properties: + + - xlnx,detector: The VTC has a timing detector + - xlnx,generator: The VTC has a timing generator + + At least one of the xlnx,detector and xlnx,generator properties must be + specified. + + +Example: + + vtc: vtc@43c40000 { + compatible = "xlnx,v-tc-6.1"; + reg = <0x43c40000 0x10000>; + + clocks = <&clkc 15>; + xlnx,generator; + }; diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt new file mode 100644 index 000000000000..9dd86b3db937 --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt @@ -0,0 +1,71 @@ +Xilinx Video Test Pattern Generator (TPG) +----------------------------------------- + +Required properties: + +- compatible: Must contain at least one of + + "xlnx,v-tpg-5.0" (TPG version 5.0) + "xlnx,v-tpg-6.0" (TPG version 6.0) + + TPG versions backward-compatible with previous versions should list all + compatible versions in the newer to older order. + +- reg: Physical base address and length of the registers set for the device. + +- clocks: Reference to the video core clock. + +- xlnx,video-format, xlnx,video-width: Video format and width, as defined in + video.txt. + +- port: Video port, using the DT bindings defined in ../video-interfaces.txt. + The TPG has a single output port numbered 0. + +Optional properties: + +- xlnx,vtc: A phandle referencing the Video Timing Controller that generates + video timings for the TPG test patterns. + +- timing-gpios: Specifier for a GPIO that controls the timing mux at the TPG + input. The GPIO active level corresponds to the selection of VTC-generated + video timings. + +The xlnx,vtc and timing-gpios properties are mandatory when the TPG is +synthesized with two ports and forbidden when synthesized with one port. + +Example: + + tpg_0: tpg@40050000 { + compatible = "xlnx,v-tpg-6.0", "xlnx,v-tpg-5.0"; + reg = <0x40050000 0x10000>; + clocks = <&clkc 15>; + + xlnx,vtc = <&vtc_3>; + timing-gpios = <&ps7_gpio_0 55 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + xlnx,video-format = ; + xlnx,video-width = <8>; + + tpg_in: endpoint { + remote-endpoint = <&adv7611_out>; + }; + }; + port@1 { + reg = <1>; + + xlnx,video-format = ; + xlnx,video-width = <8>; + + tpg1_out: endpoint { + remote-endpoint = <&switch_in0>; + }; + }: + }; + }; diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt new file mode 100644 index 000000000000..5a0227023608 --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt @@ -0,0 +1,55 @@ +Xilinx Video IP Pipeline (VIPP) +------------------------------- + +General concept +--------------- + +Xilinx video IP pipeline processes video streams through one or more Xilinx +video IP cores. Each video IP core is represented as documented in video.txt +and IP core specific documentation, xlnx,v-*.txt, in this directory. The DT +node of the VIPP represents as a top level node of the pipeline and defines +mappings between DMAs and the video IP cores. + +Required properties: + +- compatible: Must be "xlnx,video". + +- dmas, dma-names: List of one DMA specifier and identifier string (as defined + in Documentation/devicetree/bindings/dma/dma.txt) per port. Each port + requires a DMA channel with the identifier string set to "port" followed by + the port index. + +- ports: Video port, using the DT bindings defined in ../video-interfaces.txt. + +Required port properties: + +- direction: should be either "input" or "output" depending on the direction + of stream. + +Example: + + video_cap { + compatible = "xlnx,video"; + dmas = <&vdma_1 1>, <&vdma_3 1>; + dma-names = "port0", "port1"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + direction = "input"; + vcap0_in0: endpoint { + remote-endpoint = <&scaler0_out>; + }; + }; + port@1 { + reg = <1>; + direction = "input"; + vcap0_in1: endpoint { + remote-endpoint = <&switch_out1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt b/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt new file mode 100644 index 000000000000..f936b5589b19 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ingenic,jz4780-nemc.txt @@ -0,0 +1,75 @@ +* Ingenic JZ4780 NAND/external memory controller (NEMC) + +This file documents the device tree bindings for the NEMC external memory +controller in Ingenic JZ4780 + +Required properties: +- compatible: Should be set to one of: + "ingenic,jz4780-nemc" (JZ4780) +- reg: Should specify the NEMC controller registers location and length. +- clocks: Clock for the NEMC controller. +- #address-cells: Must be set to 2. +- #size-cells: Must be set to 1. +- ranges: A set of ranges for each bank describing the physical memory layout. + Each should specify the following 4 integer values: + + 0 + +Each child of the NEMC node describes a device connected to the NEMC. + +Required child node properties: +- reg: Should contain at least one register specifier, given in the following + format: + + + + Multiple registers can be specified across multiple banks. This is needed, + for example, for packaged NAND devices with multiple dies. Such devices + should be grouped into a single node. + +Optional child node properties: +- ingenic,nemc-bus-width: Specifies the bus width in bits. Defaults to 8 bits. +- ingenic,nemc-tAS: Address setup time in nanoseconds. +- ingenic,nemc-tAH: Address hold time in nanoseconds. +- ingenic,nemc-tBP: Burst pitch time in nanoseconds. +- ingenic,nemc-tAW: Access wait time in nanoseconds. +- ingenic,nemc-tSTRV: Static memory recovery time in nanoseconds. + +If a child node references multiple banks in its "reg" property, the same value +for all optional parameters will be configured for all banks. If any optional +parameters are omitted, they will be left unchanged from whatever they are +configured to when the NEMC device is probed (which may be the reset value as +given in the hardware reference manual, or a value configured by the boot +loader). + +Example (NEMC node with a NAND child device attached at CS1): + +nemc: nemc@13410000 { + compatible = "ingenic,jz4780-nemc"; + reg = <0x13410000 0x10000>; + + #address-cells = <2>; + #size-cells = <1>; + + ranges = <1 0 0x1b000000 0x1000000 + 2 0 0x1a000000 0x1000000 + 3 0 0x19000000 0x1000000 + 4 0 0x18000000 0x1000000 + 5 0 0x17000000 0x1000000 + 6 0 0x16000000 0x1000000>; + + clocks = <&cgu JZ4780_CLK_NEMC>; + + nand: nand@1 { + compatible = "ingenic,jz4780-nand"; + reg = <1 0 0x1000000>; + + ingenic,nemc-tAS = <10>; + ingenic,nemc-tAH = <5>; + ingenic,nemc-tBP = <10>; + ingenic,nemc-tAW = <15>; + ingenic,nemc-tSTRV = <100>; + + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/qcom,tcsr.txt b/Documentation/devicetree/bindings/mfd/qcom,tcsr.txt new file mode 100644 index 000000000000..e90519d566a3 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/qcom,tcsr.txt @@ -0,0 +1,22 @@ +QCOM Top Control and Status Register + +Qualcomm devices have a set of registers that provide various control and status +functions for their peripherals. This node is intended to allow access to these +registers via syscon. + +Required properties: +- compatible: Should contain: + "qcom,tcsr-ipq8064", "syscon" for IPQ8064 + "qcom,tcsr-apq8064", "syscon" for APQ8064 + "qcom,tcsr-msm8660", "syscon" for MSM8660 + "qcom,tcsr-msm8960", "syscon" for MSM8960 + "qcom,tcsr-msm8974", "syscon" for MSM8974 + "qcom,tcsr-apq8084", "syscon" for APQ8084 + "qcom,tcsr-msm8916", "syscon" for MSM8916 +- reg: Address range for TCSR registers + +Example: + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-msm8960", "syscon"; + reg = <0x1a400000 0x100>; + }; diff --git a/Documentation/devicetree/bindings/misc/lis302.txt b/Documentation/devicetree/bindings/misc/lis302.txt index 6def86f6b053..2a19bff9693f 100644 --- a/Documentation/devicetree/bindings/misc/lis302.txt +++ b/Documentation/devicetree/bindings/misc/lis302.txt @@ -46,11 +46,18 @@ Optional properties for all bus drivers: interrupt 2 - st,wakeup-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for upper/lower limit + - st,wakeup-threshold: set wakeup threshold + - st,wakeup2-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for + upper/lower limit for second wakeup + engine. + - st,wakeup2-threshold: set wakeup threshold for second wakeup + engine. - st,highpass-cutoff-hz=: 1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of highpass cut-off frequency - st,hipass{1,2}-disable: disable highpass 1/2. - st,default-rate=: set the default rate - - st,axis-{x,y,z}=: set the axis to map to the three coordinates + - st,axis-{x,y,z}=: set the axis to map to the three coordinates. + Negative values can be used for inverted axis. - st,{min,max}-limit-{x,y,z} set the min/max limits for x/y/z axis (used by self-test) diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt similarity index 61% rename from Documentation/devicetree/bindings/mtd/m25p80.txt rename to Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt index 4611aa83531b..2bee68103b01 100644 --- a/Documentation/devicetree/bindings/mtd/m25p80.txt +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt @@ -3,10 +3,13 @@ Required properties: - #address-cells, #size-cells : Must be present if the device has sub-nodes representing partitions. -- compatible : Should be the manufacturer and the name of the chip. Bear in mind - the DT binding is not Linux-only, but in case of Linux, see the - "spi_nor_ids" table in drivers/mtd/spi-nor/spi-nor.c for the list - of supported chips. +- compatible : May include a device-specific string consisting of the + manufacturer and name of the chip. Bear in mind the DT binding + is not Linux-only, but in case of Linux, see the "m25p_ids" + table in drivers/mtd/devices/m25p80.c for the list of supported + chips. + Must also include "jedec,spi-nor" for any SPI NOR flash that can + be identified by the JEDEC READ ID opcode (0x9F). - reg : Chip-Select number - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at @@ -22,7 +25,7 @@ Example: flash: m25p80@0 { #address-cells = <1>; #size-cells = <1>; - compatible = "spansion,m25p80"; + compatible = "spansion,m25p80", "jedec,spi-nor"; reg = <0>; spi-max-frequency = <40000000>; m25p,fast-read; diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt index de8b517a5521..4f833e3c4f51 100644 --- a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt +++ b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt @@ -14,7 +14,7 @@ Optional properties: - marvell,nand-enable-arbiter: Set to enable the bus arbiter - marvell,nand-keep-config: Set to keep the NAND controller config as set by the bootloader - - num-cs: Number of chipselect lines to usw + - num-cs: Number of chipselect lines to use - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false - nand-ecc-strength: number of bits to correct per ECC step diff --git a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt index 0273adb8638c..086d6f44c4b9 100644 --- a/Documentation/devicetree/bindings/mtd/sunxi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/sunxi-nand.txt @@ -21,7 +21,7 @@ Optional properties: - nand-ecc-mode : one of the supported ECC modes ("hw", "hw_syndrome", "soft", "soft_bch" or "none") -see Documentation/devicetree/mtd/nand.txt for generic bindings. +see Documentation/devicetree/bindings/mtd/nand.txt for generic bindings. Examples: diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt new file mode 100644 index 000000000000..2a3d90de18ee --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt @@ -0,0 +1,47 @@ +TI Wilink 6/7/8 (wl12xx/wl18xx) SDIO devices + +This node provides properties for controlling the wilink wireless device. The +node is expected to be specified as a child node to the SDIO controller that +connects the device to the system. + +Required properties: + - compatible: should be one of the following: + * "ti,wl1271" + * "ti,wl1273" + * "ti,wl1281" + * "ti,wl1283" + * "ti,wl1801" + * "ti,wl1805" + * "ti,wl1807" + * "ti,wl1831" + * "ti,wl1835" + * "ti,wl1837" + - interrupts : specifies attributes for the out-of-band interrupt. + +Optional properties: + - interrupt-parent : the phandle for the interrupt controller to which the + device interrupts are connected. + - ref-clock-frequency : ref clock frequency in Hz + - tcxo-clock-frequency : tcxo clock frequency in Hz + +Note: the *-clock-frequency properties assume internal clocks. In case of external +clock, new bindings (for parsing the clock nodes) have to be added. + +Example: + +&mmc3 { + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt b/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt new file mode 100644 index 000000000000..65cc0345747d --- /dev/null +++ b/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt @@ -0,0 +1,59 @@ +Freescale i.MX General Power Controller +======================================= + +The i.MX6Q General Power Control (GPC) block contains DVFS load tracking +counters and Power Gating Control (PGC) for the CPU and PU (GPU/VPU) power +domains. + +Required properties: +- compatible: Should be "fsl,imx6q-gpc" or "fsl,imx6sl-gpc" +- reg: should be register base and length as documented in the + datasheet +- interrupts: Should contain GPC interrupt request 1 +- pu-supply: Link to the LDO regulator powering the PU power domain +- clocks: Clock phandles to devices in the PU power domain that need + to be enabled during domain power-up for reset propagation. +- #power-domain-cells: Should be 1, see below: + +The gpc node is a power-controller as documented by the generic power domain +bindings in Documentation/devicetree/bindings/power/power_domain.txt. + +Example: + + gpc: gpc@020dc000 { + compatible = "fsl,imx6q-gpc"; + reg = <0x020dc000 0x4000>; + interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>, + <0 90 IRQ_TYPE_LEVEL_HIGH>; + pu-supply = <®_pu>; + clocks = <&clks IMX6QDL_CLK_GPU3D_CORE>, + <&clks IMX6QDL_CLK_GPU3D_SHADER>, + <&clks IMX6QDL_CLK_GPU2D_CORE>, + <&clks IMX6QDL_CLK_GPU2D_AXI>, + <&clks IMX6QDL_CLK_OPENVG_AXI>, + <&clks IMX6QDL_CLK_VPU_AXI>; + #power-domain-cells = <1>; + }; + + +Specifying power domain for IP modules +====================================== + +IP cores belonging to a power domain should contain a 'power-domains' property +that is a phandle pointing to the gpc device node and a DOMAIN_INDEX specifying +the power domain the device belongs to. + +Example of a device that is part of the PU power domain: + + vpu: vpu@02040000 { + reg = <0x02040000 0x3c000>; + /* ... */ + power-domains = <&gpc 1>; + /* ... */ + }; + +The following DOMAIN_INDEX values are valid for i.MX6Q: +ARM_DOMAIN 0 +PU_DOMAIN 1 +The following additional DOMAIN_INDEX value is valid for i.MX6SL: +DISPLAY_DOMAIN 2 diff --git a/Documentation/devicetree/bindings/power/renesas,sysc-rmobile.txt b/Documentation/devicetree/bindings/power/renesas,sysc-rmobile.txt index cc3b1f0a9b1a..beda7d2efc30 100644 --- a/Documentation/devicetree/bindings/power/renesas,sysc-rmobile.txt +++ b/Documentation/devicetree/bindings/power/renesas,sysc-rmobile.txt @@ -11,6 +11,7 @@ Required properties: - compatible: Should be "renesas,sysc-", "renesas,sysc-rmobile" as fallback. Examples with soctypes are: + - "renesas,sysc-r8a73a4" (R-Mobile APE6) - "renesas,sysc-r8a7740" (R-Mobile A1) - "renesas,sysc-sh73a0" (SH-Mobile AG5) - reg: Two address start and address range blocks for the device: diff --git a/Documentation/devicetree/bindings/pwm/imx-pwm.txt b/Documentation/devicetree/bindings/pwm/imx-pwm.txt index b50d7a6d9d7f..e00c2e9f484d 100644 --- a/Documentation/devicetree/bindings/pwm/imx-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/imx-pwm.txt @@ -1,10 +1,17 @@ Freescale i.MX PWM controller Required properties: -- compatible: should be "fsl,-pwm" +- compatible : should be "fsl,-pwm" and one of the following + compatible strings: + - "fsl,imx1-pwm" for PWM compatible with the one integrated on i.MX1 + - "fsl,imx27-pwm" for PWM compatible with the one integrated on i.MX27 - reg: physical base address and length of the controller's registers - #pwm-cells: should be 2. See pwm.txt in this directory for a description of the cells format. +- clocks : Clock specifiers for both ipg and per clocks. +- clock-names : Clock names should include both "ipg" and "per" +See the clock consumer binding, + Documentation/devicetree/bindings/clock/clock-bindings.txt - interrupts: The interrupt for the pwm controller Example: @@ -13,5 +20,8 @@ pwm1: pwm@53fb4000 { #pwm-cells = <2>; compatible = "fsl,imx53-pwm", "fsl,imx27-pwm"; reg = <0x53fb4000 0x4000>; + clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>, + <&clks IMX5_CLK_PWM1_HF_GATE>; + clock-names = "ipg", "per"; interrupts = <61>; }; diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt new file mode 100644 index 000000000000..be789685a1c2 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt @@ -0,0 +1,30 @@ +Abracon ABX80X I2C ultra low power RTC/Alarm chip + +The Abracon ABX80X family consist of the ab0801, ab0803, ab0804, ab0805, ab1801, +ab1803, ab1804 and ab1805. The ab0805 is the superset of ab080x and the ab1805 +is the superset of ab180x. + +Required properties: + + - "compatible": should one of: + "abracon,abx80x" + "abracon,ab0801" + "abracon,ab0803" + "abracon,ab0804" + "abracon,ab0805" + "abracon,ab1801" + "abracon,ab1803" + "abracon,ab1804" + "abracon,ab1805" + Using "abracon,abx80x" will enable chip autodetection. + - "reg": I2C bus address of the device + +Optional properties: + +The abx804 and abx805 have a trickle charger that is able to charge the +connected battery or supercap. Both the following properties have to be defined +and valid to enable charging: + + - "abracon,tc-diode": should be "standard" (0.6V) or "schottky" (0.3V) + - "abracon,tc-resistor": should be <0>, <3>, <6> or <11>. 0 disables the output + resistor, the other values are in ohm. diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt index a6391e70a8fd..90787aa2e648 100644 --- a/Documentation/devicetree/bindings/serial/atmel-usart.txt +++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt @@ -1,9 +1,10 @@ * Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART) Required properties: -- compatible: Should be "atmel,-usart" +- compatible: Should be "atmel,-usart" or "atmel,-dbgu" The compatible indicated will be the first SoC to support an additional mode or an USART new feature. + For the dbgu UART, use "atmel,-dbgu", "atmel,-usart" - reg: Should contain registers location and length - interrupts: Should contain interrupt - clock-names: tuple listing input clock names. diff --git a/Documentation/devicetree/bindings/serial/omap_serial.txt b/Documentation/devicetree/bindings/serial/omap_serial.txt index 342eedd10050..54c2a155c783 100644 --- a/Documentation/devicetree/bindings/serial/omap_serial.txt +++ b/Documentation/devicetree/bindings/serial/omap_serial.txt @@ -4,7 +4,27 @@ Required properties: - compatible : should be "ti,omap2-uart" for OMAP2 controllers - compatible : should be "ti,omap3-uart" for OMAP3 controllers - compatible : should be "ti,omap4-uart" for OMAP4 controllers +- reg : address and length of the register space +- interrupts or interrupts-extended : Should contain the uart interrupt + specifier or both the interrupt + controller phandle and interrupt + specifier. - ti,hwmods : Must be "uart", n being the instance number (1-based) Optional properties: - clock-frequency : frequency of the clock input to the UART +- dmas : DMA specifier, consisting of a phandle to the DMA controller + node and a DMA channel number. +- dma-names : "rx" for receive channel, "tx" for transmit channel. + +Example: + + uart4: serial@49042000 { + compatible = "ti,omap3-uart"; + reg = <0x49042000 0x400>; + interrupts = <80>; + dmas = <&sdma 81 &sdma 82>; + dma-names = "tx", "rx"; + ti,hwmods = "uart4"; + clock-frequency = <48000000>; + }; diff --git a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt new file mode 100644 index 000000000000..ddeb5b6a53c1 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt @@ -0,0 +1,58 @@ +MediaTek PMIC Wrapper Driver + +This document describes the binding for the MediaTek PMIC wrapper. + +On MediaTek SoCs the PMIC is connected via SPI. The SPI master interface +is not directly visible to the CPU, but only through the PMIC wrapper +inside the SoC. The communication between the SoC and the PMIC can +optionally be encrypted. Also a non standard Dual IO SPI mode can be +used to increase speed. + +IP Pairing + +on MT8135 the pins of some SoC internal peripherals can be on the PMIC. +The signals of these pins are routed over the SPI bus using the pwrap +bridge. In the binding description below the properties needed for bridging +are marked with "IP Pairing". These are optional on SoCs which do not support +IP Pairing + +Required properties in pwrap device node. +- compatible: + "mediatek,mt8135-pwrap" for MT8135 SoCs + "mediatek,mt8173-pwrap" for MT8173 SoCs +- interrupts: IRQ for pwrap in SOC +- reg-names: Must include the following entries: + "pwrap": Main registers base + "pwrap-bridge": bridge base (IP Pairing) +- reg: Must contain an entry for each entry in reg-names. +- reset-names: Must include the following entries: + "pwrap" + "pwrap-bridge" (IP Pairing) +- resets: Must contain an entry for each entry in reset-names. +- clock-names: Must include the following entries: + "spi": SPI bus clock + "wrap": Main module clock +- clocks: Must contain an entry for each entry in clock-names. + +Optional properities: +- pmic: Mediatek PMIC MFD is the child device of pwrap + See the following for child node definitions: + Documentation/devicetree/bindings/mfd/mt6397.txt + +Example: + pwrap: pwrap@1000f000 { + compatible = "mediatek,mt8135-pwrap"; + reg = <0 0x1000f000 0 0x1000>, + <0 0x11017000 0 0x1000>; + reg-names = "pwrap", "pwrap-bridge"; + interrupts = ; + resets = <&infracfg MT8135_INFRA_PMIC_WRAP_RST>, + <&pericfg MT8135_PERI_PWRAP_BRIDGE_SW_RST>; + reset-names = "pwrap", "pwrap-bridge"; + clocks = <&clk26m>, <&clk26m>; + clock-names = "spi", "wrap"; + + pmic { + compatible = "mediatek,mt6397"; + }; + }; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt index 4ce24d425bf1..2f5ede39bea2 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,gsbi.txt @@ -6,7 +6,8 @@ configuration settings. The mode setting will govern the input/output mode of the 4 GSBI IOs. Required properties: -- compatible: must contain "qcom,gsbi-v1.0.0" for APQ8064/IPQ8064 +- compatible: Should contain "qcom,gsbi-v1.0.0" +- cell-index: Should contain the GSBI index - reg: Address range for GSBI registers - clocks: required clock - clock-names: must contain "iface" entry @@ -16,6 +17,8 @@ Required properties: Optional properties: - qcom,crci : indicates CRCI MUX value for QUP CRCI ports. Please reference dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values. +- syscon-tcsr: indicates phandle of TCSR syscon node. Required if child uses + dma. Required properties if child node exists: - #address-cells: Must be 1 @@ -39,6 +42,7 @@ Example for APQ8064: gsbi4@16300000 { compatible = "qcom,gsbi-v1.0.0"; + cell-index = <4>; reg = <0x16300000 0x100>; clocks = <&gcc GSBI4_H_CLK>; clock-names = "iface"; @@ -48,22 +52,24 @@ Example for APQ8064: qcom,mode = ; qcom,crci = ; + syscon-tcsr = <&tcsr>; + /* child nodes go under here */ i2c_qup4: i2c@16380000 { - compatible = "qcom,i2c-qup-v1.1.1"; - reg = <0x16380000 0x1000>; - interrupts = <0 153 0>; + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x16380000 0x1000>; + interrupts = <0 153 0>; - clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>; - clock-names = "core", "iface"; + clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>; + clock-names = "core", "iface"; - clock-frequency = <200000>; + clock-frequency = <200000>; - #address-cells = <1>; - #size-cells = <0>; + #address-cells = <1>; + #size-cells = <0>; - }; + }; uart4: serial@16340000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; @@ -76,3 +82,7 @@ Example for APQ8064: }; }; + tcsr: syscon@1a400000 { + compatible = "qcom,apq8064-tcsr", "syscon"; + reg = <0x1a400000 0x100>; + }; diff --git a/Documentation/devicetree/bindings/sound/omap-twl4030.txt b/Documentation/devicetree/bindings/sound/omap-twl4030.txt index 1ab6bc8404d5..f6a715e4ef43 100644 --- a/Documentation/devicetree/bindings/sound/omap-twl4030.txt +++ b/Documentation/devicetree/bindings/sound/omap-twl4030.txt @@ -4,9 +4,9 @@ Required properties: - compatible: "ti,omap-twl4030" - ti,model: Name of the sound card (for example "omap3beagle") - ti,mcbsp: phandle for the McBSP node -- ti,codec: phandle for the twl4030 audio node Optional properties: +- ti,codec: phandle for the twl4030 audio node - ti,mcbsp-voice: phandle for the McBSP node connected to the voice port of twl - ti, jack-det-gpio: Jack detect GPIO - ti,audio-routing: List of connections between audio components. @@ -59,5 +59,4 @@ sound { ti,model = "omap3beagle"; ti,mcbsp = <&mcbsp2>; - ti,codec = <&twl_audio>; }; diff --git a/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt index 715d0998af8e..e16b9b5afc70 100644 --- a/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt +++ b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt @@ -1,6 +1,6 @@ Qualcomm SPMI Controller (PMIC Arbiter) -The SPMI PMIC Arbiter is found on the Snapdragon 800 Series. It is an SPMI +The SPMI PMIC Arbiter is found on Snapdragon chipsets. It is an SPMI controller with wrapping arbitration logic to allow for multiple on-chip devices to control a single SPMI master. @@ -19,6 +19,10 @@ Required properties: "core" - core registers "intr" - interrupt controller registers "cnfg" - configuration registers + Registers used only for V2 PMIC Arbiter: + "chnls" - tx-channel per virtual slave registers. + "obsrvr" - rx-channel (called observer) per virtual slave registers. + - reg : address + size pairs describing the PMIC arb register sets; order must correspond with the order of entries in reg-names - #address-cells : must be set to 2 diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 4f8edb205e13..80339192c93e 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -11,6 +11,7 @@ adapteva Adapteva, Inc. adh AD Holdings Plc. adi Analog Devices, Inc. aeroflexgaisler Aeroflex Gaisler AB +al Annapurna Labs allwinner Allwinner Technology Co., Ltd. alphascale AlphaScale Integrated Circuits Systems, Inc. altr Altera Corp. @@ -21,9 +22,11 @@ ampire Ampire Co., Ltd. ams AMS AG amstaos AMS-Taos Inc. apm Applied Micro Circuits Corporation (APM) +aptina Aptina Imaging arasan Arasan Chip Systems arm ARM Ltd. armadeus ARMadeus Systems SARL +artesyn Artesyn Embedded Technologies Inc. asahi-kasei Asahi Kasei Corp. atmel Atmel Corporation auo AU Optronics Corporation @@ -82,6 +85,7 @@ globalscale Globalscale Technologies, Inc. gmt Global Mixed-mode Technology, Inc. goodix Shenzhen Huiding Technology Co., Ltd. google Google, Inc. +grinn Grinn gumstix Gumstix, Inc. gw Gateworks Corporation hannstar HannStar Display Corporation @@ -117,6 +121,7 @@ merrii Merrii Technology Co., Ltd. micrel Micrel Inc. microchip Microchip Technology Inc. micron Micron Technology Inc. +minix MINIX Technology Ltd. mitsubishi Mitsubishi Electric Corporation mosaixtech Mosaix Technologies, Inc. moxa Moxa diff --git a/Documentation/devicetree/bindings/video/atmel,lcdc.txt b/Documentation/devicetree/bindings/video/atmel,lcdc.txt index f059dd0b3d28..ecb8da063d07 100644 --- a/Documentation/devicetree/bindings/video/atmel,lcdc.txt +++ b/Documentation/devicetree/bindings/video/atmel,lcdc.txt @@ -10,7 +10,9 @@ Required properties: "atmel,at91sam9g45es-lcdc" , "atmel,at91sam9rl-lcdc" , "atmel,at32ap-lcdc" -- reg : Should contain 1 register ranges(address and length) +- reg : Should contain 1 register ranges(address and length). + Can contain an additional register range(address and length) + for fixed framebuffer memory. Useful for dedicated memories. - interrupts : framebuffer controller interrupt - display: a phandle pointing to the display node @@ -38,6 +40,14 @@ Example: }; +Example for fixed framebuffer memory: + + fb0: fb@0x00500000 { + compatible = "atmel,at91sam9263-lcdc"; + reg = <0x00700000 0x1000 0x70000000 0x200000>; + [...] + }; + Atmel LCDC Display ----------------------------------------------------- Required properties (as per of_videomode_helper): diff --git a/Documentation/dma-buf-sharing.txt b/Documentation/dma-buf-sharing.txt index bb9753b635a3..480c8de3c2c4 100644 --- a/Documentation/dma-buf-sharing.txt +++ b/Documentation/dma-buf-sharing.txt @@ -49,25 +49,26 @@ The dma_buf buffer sharing API usage contains the following steps: The buffer exporter announces its wish to export a buffer. In this, it connects its own private buffer data, provides implementation for operations that can be performed on the exported dma_buf, and flags for the file - associated with this buffer. + associated with this buffer. All these fields are filled in struct + dma_buf_export_info, defined via the DEFINE_DMA_BUF_EXPORT_INFO macro. Interface: - struct dma_buf *dma_buf_export_named(void *priv, struct dma_buf_ops *ops, - size_t size, int flags, - const char *exp_name) + DEFINE_DMA_BUF_EXPORT_INFO(exp_info) + struct dma_buf *dma_buf_export(struct dma_buf_export_info *exp_info) - If this succeeds, dma_buf_export_named allocates a dma_buf structure, and + If this succeeds, dma_buf_export allocates a dma_buf structure, and returns a pointer to the same. It also associates an anonymous file with this buffer, so it can be exported. On failure to allocate the dma_buf object, it returns NULL. - 'exp_name' is the name of exporter - to facilitate information while - debugging. + 'exp_name' in struct dma_buf_export_info is the name of exporter - to + facilitate information while debugging. It is set to KBUILD_MODNAME by + default, so exporters don't have to provide a specific name, if they don't + wish to. + + DEFINE_DMA_BUF_EXPORT_INFO macro defines the struct dma_buf_export_info, + zeroes it out and pre-populates exp_name in it. - Exporting modules which do not wish to provide any specific name may use the - helper define 'dma_buf_export()', with the same arguments as above, but - without the last argument; a KBUILD_MODNAME pre-processor directive will be - inserted in place of 'exp_name' instead. 2. Userspace gets a handle to pass around to potential buffer-users diff --git a/Documentation/driver-model/devres.txt b/Documentation/driver-model/devres.txt index e1e2bbd7a404..831a5363f6be 100644 --- a/Documentation/driver-model/devres.txt +++ b/Documentation/driver-model/devres.txt @@ -276,6 +276,7 @@ IOMAP devm_ioport_unmap() devm_ioremap() devm_ioremap_nocache() + devm_ioremap_wc() devm_ioremap_resource() : checks resource, requests memory region, ioremaps devm_iounmap() pcim_iomap() diff --git a/Documentation/filesystems/nfs/nfs-rdma.txt b/Documentation/filesystems/nfs/nfs-rdma.txt index 724043858b08..95c13aa575ff 100644 --- a/Documentation/filesystems/nfs/nfs-rdma.txt +++ b/Documentation/filesystems/nfs/nfs-rdma.txt @@ -187,8 +187,10 @@ Check RDMA and NFS Setup To further test the InfiniBand software stack, use IPoIB (this assumes you have two IB hosts named host1 and host2): - host1$ ifconfig ib0 a.b.c.x - host2$ ifconfig ib0 a.b.c.y + host1$ ip link set dev ib0 up + host1$ ip address add dev ib0 a.b.c.x + host2$ ip link set dev ib0 up + host2$ ip address add dev ib0 a.b.c.y host1$ ping a.b.c.y host2$ ping a.b.c.x @@ -229,7 +231,8 @@ NFS/RDMA Setup $ modprobe ib_mthca $ modprobe ib_ipoib - $ ifconfig ib0 a.b.c.d + $ ip li set dev ib0 up + $ ip addr add dev ib0 a.b.c.d NOTE: use unique addresses for the client and server diff --git a/Documentation/filesystems/xfs.txt b/Documentation/filesystems/xfs.txt index 0bfafe108357..5a5a05582b58 100644 --- a/Documentation/filesystems/xfs.txt +++ b/Documentation/filesystems/xfs.txt @@ -228,30 +228,19 @@ default behaviour. Deprecated Mount Options ======================== - delaylog/nodelaylog - Delayed logging is the only logging method that XFS supports - now, so these mount options are now ignored. +None at present. - Due for removal in 3.12. - ihashsize=value - In memory inode hashes have been removed, so this option has - no function as of August 2007. Option is deprecated. +Removed Mount Options +===================== - Due for removal in 3.12. + Name Removed + ---- ------- + delaylog/nodelaylog v3.20 + ihashsize v3.20 + irixsgid v3.20 + osyncisdsync/osyncisosync v3.20 - irixsgid - This behaviour is now controlled by a sysctl, so the mount - option is ignored. - - Due for removal in 3.12. - - osyncisdsync - osyncisosync - O_SYNC and O_DSYNC are fully supported, so there is no need - for these options any more. - - Due for removal in 3.12. sysctls ======= diff --git a/Documentation/input/alps.txt b/Documentation/input/alps.txt index b9d229fee6b9..c86f2f1ae4f6 100644 --- a/Documentation/input/alps.txt +++ b/Documentation/input/alps.txt @@ -94,6 +94,10 @@ PS/2 packet format Note that the device never signals overflow condition. +For protocol version 2 devices when the trackpoint is used, and no fingers +are on the touchpad, the M R L bits signal the combined status of both the +pointingstick and touchpad buttons. + ALPS Absolute Mode - Protocol Version 1 -------------------------------------- @@ -107,7 +111,7 @@ ALPS Absolute Mode - Protocol Version 1 ALPS Absolute Mode - Protocol Version 2 --------------------------------------- - byte 0: 1 ? ? ? 1 ? ? ? + byte 0: 1 ? ? ? 1 PSM PSR PSL byte 1: 0 x6 x5 x4 x3 x2 x1 x0 byte 2: 0 x10 x9 x8 x7 ? fin ges byte 3: 0 y9 y8 y7 1 M R L @@ -115,7 +119,8 @@ ALPS Absolute Mode - Protocol Version 2 byte 5: 0 z6 z5 z4 z3 z2 z1 z0 Protocol Version 2 DualPoint devices send standard PS/2 mouse packets for -the DualPoint Stick. +the DualPoint Stick. For non interleaved dualpoint devices the pointingstick +buttons get reported separately in the PSM, PSR and PSL bits. Dualpoint device -- interleaved packet format --------------------------------------------- diff --git a/Documentation/ioctl/ioctl-number.txt b/Documentation/ioctl/ioctl-number.txt index 8136e1fd30fd..51f4221657bf 100644 --- a/Documentation/ioctl/ioctl-number.txt +++ b/Documentation/ioctl/ioctl-number.txt @@ -321,6 +321,7 @@ Code Seq#(hex) Include File Comments 0xDB 00-0F drivers/char/mwave/mwavepub.h 0xDD 00-3F ZFCP device driver see drivers/s390/scsi/ +0xEC 00-01 drivers/platform/chrome/cros_ec_dev.h ChromeOS EC driver 0xF3 00-3F drivers/usb/misc/sisusbvga/sisusb.h sisfb (in development) 0xF4 00-1F video/mbxfb.h mbxfb diff --git a/Documentation/kasan.txt b/Documentation/kasan.txt index 092fc10961fe..4692241789b1 100644 --- a/Documentation/kasan.txt +++ b/Documentation/kasan.txt @@ -9,7 +9,9 @@ a fast and comprehensive solution for finding use-after-free and out-of-bounds bugs. KASan uses compile-time instrumentation for checking every memory access, -therefore you will need a certain version of GCC > 4.9.2 +therefore you will need a gcc version of 4.9.2 or later. KASan could detect out +of bounds accesses to stack or global variables, but only if gcc 5.0 or later was +used to built the kernel. Currently KASan is supported only for x86_64 architecture and requires that the kernel be built with the SLUB allocator. @@ -23,8 +25,8 @@ To enable KASAN configure kernel with: and choose between CONFIG_KASAN_OUTLINE and CONFIG_KASAN_INLINE. Outline/inline is compiler instrumentation types. The former produces smaller binary the -latter is 1.1 - 2 times faster. Inline instrumentation requires GCC 5.0 or -latter. +latter is 1.1 - 2 times faster. Inline instrumentation requires a gcc version +of 5.0 or later. Currently KASAN works only with the SLUB memory allocator. For better bug detection and nicer report, enable CONFIG_STACKTRACE and put diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 274252f205b7..61ab1628a057 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -165,7 +165,7 @@ multipliers 'Kilo', 'Mega', and 'Giga', equalling 2^10, 2^20, and 2^30 bytes respectively. Such letter suffixes can also be entirely omitted. - acpi= [HW,ACPI,X86] + acpi= [HW,ACPI,X86,ARM64] Advanced Configuration and Power Interface Format: { force | off | strict | noirq | rsdt } force -- enable ACPI if default was off @@ -175,6 +175,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted. strictly ACPI specification compliant. rsdt -- prefer RSDT over (default) XSDT copy_dsdt -- copy DSDT to memory + For ARM64, ONLY "acpi=off" or "acpi=force" are available See also Documentation/power/runtime_pm.txt, pci=noacpi @@ -713,10 +714,18 @@ bytes respectively. Such letter suffixes can also be entirely omitted. uart[8250],io,[,options] uart[8250],mmio,[,options] + uart[8250],mmio32,[,options] + uart[8250],0x[,options] Start an early, polled-mode console on the 8250/16550 UART at the specified I/O port or MMIO address, - switching to the matching ttyS device later. The - options are the same as for ttyS, above. + switching to the matching ttyS device later. + MMIO inter-register address stride is either 8-bit + (mmio) or 32-bit (mmio32). + If none of [io|mmio|mmio32], is assumed to be + equivalent to 'mmio'. 'options' are specified in the + same format described for ttyS above; if unspecified, + the h/w is not re-initialized. + hvc Use the hypervisor console device . This is for both Xen and PowerPC hypervisors. @@ -950,11 +959,15 @@ bytes respectively. Such letter suffixes can also be entirely omitted. uart[8250],io,[,options] uart[8250],mmio,[,options] uart[8250],mmio32,[,options] + uart[8250],0x[,options] Start an early, polled-mode console on the 8250/16550 UART at the specified I/O port or MMIO address. MMIO inter-register address stride is either 8-bit (mmio) or 32-bit (mmio32). - The options are the same as for ttyS, above. + If none of [io|mmio|mmio32], is assumed to be + equivalent to 'mmio'. 'options' are specified in the + same format described for "console=ttyS"; if + unspecified, the h/w is not initialized. pl011, Start an early, polled-mode console on a pl011 serial @@ -3774,6 +3787,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted. READ_CAPACITY_16 command); f = NO_REPORT_OPCODES (don't use report opcodes command, uas only); + g = MAX_SECTORS_240 (don't transfer more than + 240 sectors at a time, uas only); h = CAPACITY_HEURISTICS (decrease the reported device capacity by one sector if the number is odd); diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt index fc04c14de4bb..72a150d8f3df 100644 --- a/Documentation/laptops/thinkpad-acpi.txt +++ b/Documentation/laptops/thinkpad-acpi.txt @@ -1355,6 +1355,24 @@ Sysfs notes: rfkill controller switch "tpacpi_uwb_sw": refer to Documentation/rfkill.txt for details. +Adaptive keyboard +----------------- + +sysfs device attribute: adaptive_kbd_mode + +This sysfs attribute controls the keyboard "face" that will be shown on the +Lenovo X1 Carbon 2nd gen (2014)'s adaptive keyboard. The value can be read +and set. + +1 = Home mode +2 = Web-browser mode +3 = Web-conference mode +4 = Function mode +5 = Layflat mode + +For more details about which buttons will appear depending on the mode, please +review the laptop's user guide: +http://www.lenovo.com/shop/americas/content/user_guides/x1carbon_2_ug_en.pdf Multiple Commands, Module Parameters ------------------------------------ diff --git a/Documentation/md-cluster.txt b/Documentation/md-cluster.txt new file mode 100644 index 000000000000..de1af7db3355 --- /dev/null +++ b/Documentation/md-cluster.txt @@ -0,0 +1,176 @@ +The cluster MD is a shared-device RAID for a cluster. + + +1. On-disk format + +Separate write-intent-bitmap are used for each cluster node. +The bitmaps record all writes that may have been started on that node, +and may not yet have finished. The on-disk layout is: + +0 4k 8k 12k +------------------------------------------------------------------- +| idle | md super | bm super [0] + bits | +| bm bits[0, contd] | bm super[1] + bits | bm bits[1, contd] | +| bm super[2] + bits | bm bits [2, contd] | bm super[3] + bits | +| bm bits [3, contd] | | | + +During "normal" functioning we assume the filesystem ensures that only one +node writes to any given block at a time, so a write +request will + - set the appropriate bit (if not already set) + - commit the write to all mirrors + - schedule the bit to be cleared after a timeout. + +Reads are just handled normally. It is up to the filesystem to +ensure one node doesn't read from a location where another node (or the same +node) is writing. + + +2. DLM Locks for management + +There are two locks for managing the device: + +2.1 Bitmap lock resource (bm_lockres) + + The bm_lockres protects individual node bitmaps. They are named in the + form bitmap001 for node 1, bitmap002 for node and so on. When a node + joins the cluster, it acquires the lock in PW mode and it stays so + during the lifetime the node is part of the cluster. The lock resource + number is based on the slot number returned by the DLM subsystem. Since + DLM starts node count from one and bitmap slots start from zero, one is + subtracted from the DLM slot number to arrive at the bitmap slot number. + +3. Communication + +Each node has to communicate with other nodes when starting or ending +resync, and metadata superblock updates. + +3.1 Message Types + + There are 3 types, of messages which are passed + + 3.1.1 METADATA_UPDATED: informs other nodes that the metadata has been + updated, and the node must re-read the md superblock. This is performed + synchronously. + + 3.1.2 RESYNC: informs other nodes that a resync is initiated or ended + so that each node may suspend or resume the region. + +3.2 Communication mechanism + + The DLM LVB is used to communicate within nodes of the cluster. There + are three resources used for the purpose: + + 3.2.1 Token: The resource which protects the entire communication + system. The node having the token resource is allowed to + communicate. + + 3.2.2 Message: The lock resource which carries the data to + communicate. + + 3.2.3 Ack: The resource, acquiring which means the message has been + acknowledged by all nodes in the cluster. The BAST of the resource + is used to inform the receive node that a node wants to communicate. + +The algorithm is: + + 1. receive status + + sender receiver receiver + ACK:CR ACK:CR ACK:CR + + 2. sender get EX of TOKEN + sender get EX of MESSAGE + sender receiver receiver + TOKEN:EX ACK:CR ACK:CR + MESSAGE:EX + ACK:CR + + Sender checks that it still needs to send a message. Messages received + or other events that happened while waiting for the TOKEN may have made + this message inappropriate or redundant. + + 3. sender write LVB. + sender down-convert MESSAGE from EX to CR + sender try to get EX of ACK + [ wait until all receiver has *processed* the MESSAGE ] + + [ triggered by bast of ACK ] + receiver get CR of MESSAGE + receiver read LVB + receiver processes the message + [ wait finish ] + receiver release ACK + + sender receiver receiver + TOKEN:EX MESSAGE:CR MESSAGE:CR + MESSAGE:CR + ACK:EX + + 4. triggered by grant of EX on ACK (indicating all receivers have processed + message) + sender down-convert ACK from EX to CR + sender release MESSAGE + sender release TOKEN + receiver upconvert to EX of MESSAGE + receiver get CR of ACK + receiver release MESSAGE + + sender receiver receiver + ACK:CR ACK:CR ACK:CR + + +4. Handling Failures + +4.1 Node Failure + When a node fails, the DLM informs the cluster with the slot. The node + starts a cluster recovery thread. The cluster recovery thread: + - acquires the bitmap lock of the failed node + - opens the bitmap + - reads the bitmap of the failed node + - copies the set bitmap to local node + - cleans the bitmap of the failed node + - releases bitmap lock of the failed node + - initiates resync of the bitmap on the current node + + The resync process, is the regular md resync. However, in a clustered + environment when a resync is performed, it needs to tell other nodes + of the areas which are suspended. Before a resync starts, the node + send out RESYNC_START with the (lo,hi) range of the area which needs + to be suspended. Each node maintains a suspend_list, which contains + the list of ranges which are currently suspended. On receiving + RESYNC_START, the node adds the range to the suspend_list. Similarly, + when the node performing resync finishes, it send RESYNC_FINISHED + to other nodes and other nodes remove the corresponding entry from + the suspend_list. + + A helper function, should_suspend() can be used to check if a particular + I/O range should be suspended or not. + +4.2 Device Failure + Device failures are handled and communicated with the metadata update + routine. + +5. Adding a new Device +For adding a new device, it is necessary that all nodes "see" the new device +to be added. For this, the following algorithm is used: + + 1. Node 1 issues mdadm --manage /dev/mdX --add /dev/sdYY which issues + ioctl(ADD_NEW_DISC with disc.state set to MD_DISK_CLUSTER_ADD) + 2. Node 1 sends NEWDISK with uuid and slot number + 3. Other nodes issue kobject_uevent_env with uuid and slot number + (Steps 4,5 could be a udev rule) + 4. In userspace, the node searches for the disk, perhaps + using blkid -t SUB_UUID="" + 5. Other nodes issue either of the following depending on whether the disk + was found: + ioctl(ADD_NEW_DISK with disc.state set to MD_DISK_CANDIDATE and + disc.number set to slot number) + ioctl(CLUSTERED_DISK_NACK) + 6. Other nodes drop lock on no-new-devs (CR) if device is found + 7. Node 1 attempts EX lock on no-new-devs + 8. If node 1 gets the lock, it sends METADATA_UPDATED after unmarking the disk + as SpareLocal + 9. If not (get no-new-dev lock), it fails the operation and sends METADATA_UPDATED + 10. Other nodes get the information whether a disk is added or not + by the following METADATA_UPDATED. diff --git a/Documentation/module-signing.txt b/Documentation/module-signing.txt index 09c2382ad055..c72702ec1ded 100644 --- a/Documentation/module-signing.txt +++ b/Documentation/module-signing.txt @@ -119,9 +119,9 @@ Most notably, in the x509.genkey file, the req_distinguished_name section should be altered from the default: [ req_distinguished_name ] - O = Magrathea - CN = Glacier signing key - emailAddress = slartibartfast@magrathea.h2g2 + #O = Unspecified company + CN = Build time autogenerated kernel key + #emailAddress = unspecified.user@unspecified.company The generated RSA key size can also be set with: diff --git a/Documentation/networking/mpls-sysctl.txt b/Documentation/networking/mpls-sysctl.txt index 639ddf0ece9b..9ed15f86c17c 100644 --- a/Documentation/networking/mpls-sysctl.txt +++ b/Documentation/networking/mpls-sysctl.txt @@ -18,3 +18,12 @@ platform_labels - INTEGER Possible values: 0 - 1048575 Default: 0 + +conf//input - BOOL + Control whether packets can be input on this interface. + + If disabled, packets will be discarded without further + processing. + + 0 - disabled (default) + not 0 - enabled diff --git a/Documentation/networking/scaling.txt b/Documentation/networking/scaling.txt index cbfac0949635..59f4db2a0c85 100644 --- a/Documentation/networking/scaling.txt +++ b/Documentation/networking/scaling.txt @@ -282,7 +282,7 @@ following is true: - The current CPU's queue head counter >= the recorded tail counter value in rps_dev_flow[i] -- The current CPU is unset (equal to RPS_NO_CPU) +- The current CPU is unset (>= nr_cpu_ids) - The current CPU is offline After this check, the packet is sent to the (possibly updated) current diff --git a/Documentation/powerpc/transactional_memory.txt b/Documentation/powerpc/transactional_memory.txt index ba0a2a4a54ba..ded69794a5c0 100644 --- a/Documentation/powerpc/transactional_memory.txt +++ b/Documentation/powerpc/transactional_memory.txt @@ -74,23 +74,22 @@ Causes of transaction aborts Syscalls ======== -Syscalls made from within an active transaction will not be performed and the -transaction will be doomed by the kernel with the failure code TM_CAUSE_SYSCALL -| TM_CAUSE_PERSISTENT. +Performing syscalls from within transaction is not recommended, and can lead +to unpredictable results. -Syscalls made from within a suspended transaction are performed as normal and -the transaction is not explicitly doomed by the kernel. However, what the -kernel does to perform the syscall may result in the transaction being doomed -by the hardware. The syscall is performed in suspended mode so any side -effects will be persistent, independent of transaction success or failure. No -guarantees are provided by the kernel about which syscalls will affect -transaction success. +Syscalls do not by design abort transactions, but beware: The kernel code will +not be running in transactional state. The effect of syscalls will always +remain visible, but depending on the call they may abort your transaction as a +side-effect, read soon-to-be-aborted transactional data that should not remain +invisible, etc. If you constantly retry a transaction that constantly aborts +itself by calling a syscall, you'll have a livelock & make no progress. -Care must be taken when relying on syscalls to abort during active transactions -if the calls are made via a library. Libraries may cache values (which may -give the appearance of success) or perform operations that cause transaction -failure before entering the kernel (which may produce different failure codes). -Examples are glibc's getpid() and lazy symbol resolution. +Simple syscalls (e.g. sigprocmask()) "could" be OK. Even things like write() +from, say, printf() should be OK as long as the kernel does not access any +memory that was accessed transactionally. + +Consider any syscalls that happen to work as debug-only -- not recommended for +production use. Best to queue them up till after the transaction is over. Signals @@ -177,7 +176,8 @@ kernel aborted a transaction: TM_CAUSE_RESCHED Thread was rescheduled. TM_CAUSE_TLBI Software TLB invalid. TM_CAUSE_FAC_UNAV FP/VEC/VSX unavailable trap. - TM_CAUSE_SYSCALL Syscall from active transaction. + TM_CAUSE_SYSCALL Currently unused; future syscalls that must abort + transactions for consistency will use this. TM_CAUSE_SIGNAL Signal delivered. TM_CAUSE_MISC Currently unused. TM_CAUSE_ALIGNMENT Alignment fault. diff --git a/Documentation/serial/tty.txt b/Documentation/serial/tty.txt index 1e52d67d0abf..dbe6623fed1c 100644 --- a/Documentation/serial/tty.txt +++ b/Documentation/serial/tty.txt @@ -198,6 +198,9 @@ TTY_IO_ERROR If set, causes all subsequent userspace read/write TTY_OTHER_CLOSED Device is a pty and the other side has closed. +TTY_OTHER_DONE Device is a pty and the other side has closed and + all pending input processing has been completed. + TTY_NO_WRITE_SPLIT Prevent driver from splitting up writes into smaller chunks. diff --git a/Documentation/target/tcm_mod_builder.py b/Documentation/target/tcm_mod_builder.py index 2b47704f75cb..2ba71cea0172 100755 --- a/Documentation/target/tcm_mod_builder.py +++ b/Documentation/target/tcm_mod_builder.py @@ -237,8 +237,7 @@ def tcm_mod_build_configfs(proto_ident, fabric_mod_dir_var, fabric_mod_name): buf += "#include \"" + fabric_mod_name + "_base.h\"\n" buf += "#include \"" + fabric_mod_name + "_fabric.h\"\n\n" - buf += "/* Local pointer to allocated TCM configfs fabric module */\n" - buf += "struct target_fabric_configfs *" + fabric_mod_name + "_fabric_configfs;\n\n" + buf += "static const struct target_core_fabric_ops " + fabric_mod_name + "_ops;\n\n" buf += "static struct se_node_acl *" + fabric_mod_name + "_make_nodeacl(\n" buf += " struct se_portal_group *se_tpg,\n" @@ -309,8 +308,8 @@ def tcm_mod_build_configfs(proto_ident, fabric_mod_dir_var, fabric_mod_name): buf += " }\n" buf += " tpg->" + fabric_mod_port + " = " + fabric_mod_port + ";\n" buf += " tpg->" + fabric_mod_port + "_tpgt = tpgt;\n\n" - buf += " ret = core_tpg_register(&" + fabric_mod_name + "_fabric_configfs->tf_ops, wwn,\n" - buf += " &tpg->se_tpg, (void *)tpg,\n" + buf += " ret = core_tpg_register(&" + fabric_mod_name + "_ops, wwn,\n" + buf += " &tpg->se_tpg, tpg,\n" buf += " TRANSPORT_TPG_TYPE_NORMAL);\n" buf += " if (ret < 0) {\n" buf += " kfree(tpg);\n" @@ -370,7 +369,10 @@ def tcm_mod_build_configfs(proto_ident, fabric_mod_dir_var, fabric_mod_name): buf += " NULL,\n" buf += "};\n\n" - buf += "static struct target_core_fabric_ops " + fabric_mod_name + "_ops = {\n" + buf += "static const struct target_core_fabric_ops " + fabric_mod_name + "_ops = {\n" + buf += " .module = THIS_MODULE,\n" + buf += " .name = " + fabric_mod_name + ",\n" + buf += " .get_fabric_proto_ident = " + fabric_mod_name + "_get_fabric_proto_ident,\n" buf += " .get_fabric_name = " + fabric_mod_name + "_get_fabric_name,\n" buf += " .get_fabric_proto_ident = " + fabric_mod_name + "_get_fabric_proto_ident,\n" buf += " .tpg_get_wwn = " + fabric_mod_name + "_get_fabric_wwn,\n" @@ -413,75 +415,18 @@ def tcm_mod_build_configfs(proto_ident, fabric_mod_dir_var, fabric_mod_name): buf += " .fabric_drop_np = NULL,\n" buf += " .fabric_make_nodeacl = " + fabric_mod_name + "_make_nodeacl,\n" buf += " .fabric_drop_nodeacl = " + fabric_mod_name + "_drop_nodeacl,\n" - buf += "};\n\n" - - buf += "static int " + fabric_mod_name + "_register_configfs(void)\n" - buf += "{\n" - buf += " struct target_fabric_configfs *fabric;\n" - buf += " int ret;\n\n" - buf += " printk(KERN_INFO \"" + fabric_mod_name.upper() + " fabric module %s on %s/%s\"\n" - buf += " \" on \"UTS_RELEASE\"\\n\"," + fabric_mod_name.upper() + "_VERSION, utsname()->sysname,\n" - buf += " utsname()->machine);\n" - buf += " /*\n" - buf += " * Register the top level struct config_item_type with TCM core\n" - buf += " */\n" - buf += " fabric = target_fabric_configfs_init(THIS_MODULE, \"" + fabric_mod_name + "\");\n" - buf += " if (IS_ERR(fabric)) {\n" - buf += " printk(KERN_ERR \"target_fabric_configfs_init() failed\\n\");\n" - buf += " return PTR_ERR(fabric);\n" - buf += " }\n" - buf += " /*\n" - buf += " * Setup fabric->tf_ops from our local " + fabric_mod_name + "_ops\n" - buf += " */\n" - buf += " fabric->tf_ops = " + fabric_mod_name + "_ops;\n" - buf += " /*\n" - buf += " * Setup default attribute lists for various fabric->tf_cit_tmpl\n" - buf += " */\n" - buf += " fabric->tf_cit_tmpl.tfc_wwn_cit.ct_attrs = " + fabric_mod_name + "_wwn_attrs;\n" - buf += " fabric->tf_cit_tmpl.tfc_tpg_base_cit.ct_attrs = NULL;\n" - buf += " fabric->tf_cit_tmpl.tfc_tpg_attrib_cit.ct_attrs = NULL;\n" - buf += " fabric->tf_cit_tmpl.tfc_tpg_param_cit.ct_attrs = NULL;\n" - buf += " fabric->tf_cit_tmpl.tfc_tpg_np_base_cit.ct_attrs = NULL;\n" - buf += " fabric->tf_cit_tmpl.tfc_tpg_nacl_base_cit.ct_attrs = NULL;\n" - buf += " fabric->tf_cit_tmpl.tfc_tpg_nacl_attrib_cit.ct_attrs = NULL;\n" - buf += " fabric->tf_cit_tmpl.tfc_tpg_nacl_auth_cit.ct_attrs = NULL;\n" - buf += " fabric->tf_cit_tmpl.tfc_tpg_nacl_param_cit.ct_attrs = NULL;\n" - buf += " /*\n" - buf += " * Register the fabric for use within TCM\n" - buf += " */\n" - buf += " ret = target_fabric_configfs_register(fabric);\n" - buf += " if (ret < 0) {\n" - buf += " printk(KERN_ERR \"target_fabric_configfs_register() failed\"\n" - buf += " \" for " + fabric_mod_name.upper() + "\\n\");\n" - buf += " return ret;\n" - buf += " }\n" - buf += " /*\n" - buf += " * Setup our local pointer to *fabric\n" - buf += " */\n" - buf += " " + fabric_mod_name + "_fabric_configfs = fabric;\n" - buf += " printk(KERN_INFO \"" + fabric_mod_name.upper() + "[0] - Set fabric -> " + fabric_mod_name + "_fabric_configfs\\n\");\n" - buf += " return 0;\n" - buf += "};\n\n" - buf += "static void __exit " + fabric_mod_name + "_deregister_configfs(void)\n" - buf += "{\n" - buf += " if (!" + fabric_mod_name + "_fabric_configfs)\n" - buf += " return;\n\n" - buf += " target_fabric_configfs_deregister(" + fabric_mod_name + "_fabric_configfs);\n" - buf += " " + fabric_mod_name + "_fabric_configfs = NULL;\n" - buf += " printk(KERN_INFO \"" + fabric_mod_name.upper() + "[0] - Cleared " + fabric_mod_name + "_fabric_configfs\\n\");\n" + buf += "\n" + buf += " .tfc_wwn_attrs = " + fabric_mod_name + "_wwn_attrs;\n" buf += "};\n\n" buf += "static int __init " + fabric_mod_name + "_init(void)\n" buf += "{\n" - buf += " int ret;\n\n" - buf += " ret = " + fabric_mod_name + "_register_configfs();\n" - buf += " if (ret < 0)\n" - buf += " return ret;\n\n" - buf += " return 0;\n" + buf += " return target_register_template(" + fabric_mod_name + "_ops);\n" buf += "};\n\n" + buf += "static void __exit " + fabric_mod_name + "_exit(void)\n" buf += "{\n" - buf += " " + fabric_mod_name + "_deregister_configfs();\n" + buf += " target_unregister_template(" + fabric_mod_name + "_ops);\n" buf += "};\n\n" buf += "MODULE_DESCRIPTION(\"" + fabric_mod_name.upper() + " series fabric driver\");\n" diff --git a/Documentation/target/tcmu-design.txt b/Documentation/target/tcmu-design.txt index 5518465290bf..43e94ea6d2ca 100644 --- a/Documentation/target/tcmu-design.txt +++ b/Documentation/target/tcmu-design.txt @@ -138,27 +138,40 @@ signals the kernel via a 4-byte write(). When cmd_head equals cmd_tail, the ring is empty -- no commands are currently waiting to be processed by userspace. -TCMU commands start with a common header containing "len_op", a 32-bit -value that stores the length, as well as the opcode in the lowest -unused bits. Currently only two opcodes are defined, TCMU_OP_PAD and -TCMU_OP_CMD. When userspace encounters a command with PAD opcode, it -should skip ahead by the bytes in "length". (The kernel inserts PAD -entries to ensure each CMD entry fits contigously into the circular -buffer.) +TCMU commands are 8-byte aligned. They start with a common header +containing "len_op", a 32-bit value that stores the length, as well as +the opcode in the lowest unused bits. It also contains cmd_id and +flags fields for setting by the kernel (kflags) and userspace +(uflags). -When userspace handles a CMD, it finds the SCSI CDB (Command Data -Block) via tcmu_cmd_entry.req.cdb_off. This is an offset from the -start of the overall shared memory region, not the entry. The data -in/out buffers are accessible via tht req.iov[] array. Note that -each iov.iov_base is also an offset from the start of the region. +Currently only two opcodes are defined, TCMU_OP_CMD and TCMU_OP_PAD. -TCMU currently does not support BIDI operations. +When the opcode is CMD, the entry in the command ring is a struct +tcmu_cmd_entry. Userspace finds the SCSI CDB (Command Data Block) via +tcmu_cmd_entry.req.cdb_off. This is an offset from the start of the +overall shared memory region, not the entry. The data in/out buffers +are accessible via tht req.iov[] array. iov_cnt contains the number of +entries in iov[] needed to describe either the Data-In or Data-Out +buffers. For bidirectional commands, iov_cnt specifies how many iovec +entries cover the Data-Out area, and iov_bidi_count specifies how many +iovec entries immediately after that in iov[] cover the Data-In +area. Just like other fields, iov.iov_base is an offset from the start +of the region. When completing a command, userspace sets rsp.scsi_status, and rsp.sense_buffer if necessary. Userspace then increments mailbox.cmd_tail by entry.hdr.length (mod cmdr_size) and signals the kernel via the UIO method, a 4-byte write to the file descriptor. +When the opcode is PAD, userspace only updates cmd_tail as above -- +it's a no-op. (The kernel inserts PAD entries to ensure each CMD entry +is contiguous within the command ring.) + +More opcodes may be added in the future. If userspace encounters an +opcode it does not handle, it must set UNKNOWN_OP bit (bit 0) in +hdr.uflags, update cmd_tail, and proceed with processing additional +commands, if any. + The Data Area: This is shared-memory space after the command ring. The organization diff --git a/Documentation/trace/coresight.txt b/Documentation/trace/coresight.txt index 02361552a3ea..77d14d51a670 100644 --- a/Documentation/trace/coresight.txt +++ b/Documentation/trace/coresight.txt @@ -14,7 +14,7 @@ document is concerned with the latter. HW assisted tracing is becoming increasingly useful when dealing with systems that have many SoCs and other components like GPU and DMA engines. ARM has developed a HW assisted tracing solution by means of different components, each -being added to a design at systhesis time to cater to specific tracing needs. +being added to a design at synthesis time to cater to specific tracing needs. Compoments are generally categorised as source, link and sinks and are (usually) discovered using the AMBA bus. diff --git a/Documentation/video4linux/v4l2-controls.txt b/Documentation/video4linux/v4l2-controls.txt index 0f84ce8c9a7b..5517db602f37 100644 --- a/Documentation/video4linux/v4l2-controls.txt +++ b/Documentation/video4linux/v4l2-controls.txt @@ -344,7 +344,9 @@ implement g_volatile_ctrl like this: } Note that you use the 'new value' union as well in g_volatile_ctrl. In general -controls that need to implement g_volatile_ctrl are read-only controls. +controls that need to implement g_volatile_ctrl are read-only controls. If they +are not, a V4L2_EVENT_CTRL_CH_VALUE will not be generated when the control +changes. To mark a control as volatile you have to set V4L2_CTRL_FLAG_VOLATILE: diff --git a/Documentation/video4linux/v4l2-framework.txt b/Documentation/video4linux/v4l2-framework.txt index f586e29ce221..59e619f9bbf5 100644 --- a/Documentation/video4linux/v4l2-framework.txt +++ b/Documentation/video4linux/v4l2-framework.txt @@ -793,8 +793,8 @@ video_register_device_no_warn() instead. Whenever a device node is created some attributes are also created for you. If you look in /sys/class/video4linux you see the devices. Go into e.g. -video0 and you will see 'name', 'debug' and 'index' attributes. The 'name' -attribute is the 'name' field of the video_device struct. The 'debug' attribute +video0 and you will see 'name', 'dev_debug' and 'index' attributes. The 'name' +attribute is the 'name' field of the video_device struct. The 'dev_debug' attribute can be used to enable core debugging. See the next section for more detailed information on this. @@ -821,7 +821,7 @@ unregister the device if the registration failed. video device debugging ---------------------- -The 'debug' attribute that is created for each video, vbi, radio or swradio +The 'dev_debug' attribute that is created for each video, vbi, radio or swradio device in /sys/class/video4linux// allows you to enable logging of file operations. diff --git a/Documentation/video4linux/vivid.txt b/Documentation/video4linux/vivid.txt index 6cfc8541a362..cd4b5a1ac529 100644 --- a/Documentation/video4linux/vivid.txt +++ b/Documentation/video4linux/vivid.txt @@ -912,6 +912,11 @@ looped to the video input provided that: sequence and field counting in struct v4l2_buffer on the capture side may not be 100% accurate. +- field settings V4L2_FIELD_SEQ_TB/BT are not supported. While it is possible to + implement this, it would mean a lot of work to get this right. Since these + field values are rarely used the decision was made not to implement this for + now. + - on the input side the "Standard Signal Mode" for the S-Video input or the "DV Timings Signal Mode" for the HDMI input should be configured so that a valid signal is passed to the video input. diff --git a/Documentation/virtual/kvm/api.txt b/Documentation/virtual/kvm/api.txt index bc9f6fe44e27..9fa2bf8c3f6f 100644 --- a/Documentation/virtual/kvm/api.txt +++ b/Documentation/virtual/kvm/api.txt @@ -3573,3 +3573,20 @@ struct { @ar - access register number KVM handlers should exit to userspace with rc = -EREMOTE. + + +8. Other capabilities. +---------------------- + +This section lists capabilities that give information about other +features of the KVM implementation. + +8.1 KVM_CAP_PPC_HWRNG + +Architectures: ppc + +This capability, if KVM_CHECK_EXTENSION indicates that it is +available, means that that the kernel has an implementation of the +H_RANDOM hypercall backed by a hardware random-number generator. +If present, the kernel H_RANDOM handler can be enabled for guest use +with the KVM_CAP_PPC_ENABLE_HCALL capability. diff --git a/MAINTAINERS b/MAINTAINERS index ce3eb0faffe6..f8e0afb708b4 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -886,12 +886,16 @@ S: Maintained F: drivers/media/rc/meson-ir.c N: meson[x68] +ARM/Annapurna Labs ALPINE ARCHITECTURE +M: Tsahee Zidenberg +S: Maintained +F: arch/arm/mach-alpine/ + ARM/ATMEL AT91RM9200 AND AT91SAM ARM ARCHITECTURES -M: Andrew Victor M: Nicolas Ferre +M: Alexandre Belloni M: Jean-Christophe Plagniol-Villard L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) -W: http://maxim.org.za/at91_26.html W: http://www.linux4sam.org S: Supported F: arch/arm/mach-at91/ @@ -958,7 +962,7 @@ ARM/CORESIGHT FRAMEWORK AND DRIVERS M: Mathieu Poirier L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) S: Maintained -F: drivers/coresight/* +F: drivers/hwtracing/coresight/* F: Documentation/trace/coresight.txt F: Documentation/devicetree/bindings/arm/coresight.txt F: Documentation/ABI/testing/sysfs-bus-coresight-devices-* @@ -970,7 +974,7 @@ S: Maintained ARM/CORTINA SYSTEMS GEMINI ARM ARCHITECTURE M: Hans Ulli Kroll L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) -T: git git://git.berlios.de/gemini-board +T: git git://github.com/ulli-kroll/linux.git S: Maintained F: arch/arm/mach-gemini/ @@ -985,6 +989,12 @@ F: drivers/clocksource/timer-prima2.c F: drivers/clocksource/timer-atlas7.c N: [^a-z]sirf +ARM/CONEXANT DIGICOLOR MACHINE SUPPORT +M: Baruch Siach +L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) +S: Maintained +N: digicolor + ARM/EBSA110 MACHINE SUPPORT M: Russell King L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) @@ -1183,7 +1193,7 @@ ARM/MAGICIAN MACHINE SUPPORT M: Philipp Zabel S: Maintained -ARM/Marvell Armada 370 and Armada XP SOC support +ARM/Marvell Kirkwood and Armada 370, 375, 38x, XP SOC support M: Jason Cooper M: Andrew Lunn M: Gregory Clement @@ -1192,12 +1202,17 @@ L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) S: Maintained F: arch/arm/mach-mvebu/ F: drivers/rtc/rtc-armada38x.c +F: arch/arm/boot/dts/armada* +F: arch/arm/boot/dts/kirkwood* + ARM/Marvell Berlin SoC support M: Sebastian Hesselbarth L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) S: Maintained F: arch/arm/mach-berlin/ +F: arch/arm/boot/dts/berlin* + ARM/Marvell Dove/MV78xx0/Orion SOC support M: Jason Cooper @@ -1210,6 +1225,9 @@ F: arch/arm/mach-dove/ F: arch/arm/mach-mv78xx0/ F: arch/arm/mach-orion5x/ F: arch/arm/plat-orion/ +F: arch/arm/boot/dts/dove* +F: arch/arm/boot/dts/orion5x* + ARM/Orion SoC/Technologic Systems TS-78xx platform support M: Alexander Clouter @@ -1261,22 +1279,6 @@ L: openmoko-kernel@lists.openmoko.org (subscribers-only) W: http://wiki.openmoko.org/wiki/Neo_FreeRunner S: Supported -ARM/QUALCOMM MSM MACHINE SUPPORT -M: David Brown -M: Daniel Walker -M: Bryan Huntsman -L: linux-arm-msm@vger.kernel.org -F: arch/arm/mach-msm/ -F: drivers/video/fbdev/msm/ -F: drivers/mmc/host/msm_sdcc.c -F: drivers/mmc/host/msm_sdcc.h -F: drivers/tty/serial/msm_serial.h -F: drivers/tty/serial/msm_serial.c -F: drivers/*/pm8???-* -F: drivers/mfd/ssbi.c -T: git git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm.git -S: Maintained - ARM/TOSA MACHINE SUPPORT M: Dmitry Eremin-Solenikov M: Dirk Opfer @@ -1334,6 +1336,11 @@ L: linux-soc@vger.kernel.org S: Maintained F: arch/arm/mach-qcom/ F: drivers/soc/qcom/ +F: drivers/tty/serial/msm_serial.h +F: drivers/tty/serial/msm_serial.c +F: drivers/*/pm8???-* +F: drivers/mfd/ssbi.c +F: drivers/firmware/qcom_scm.c T: git git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom.git ARM/RADISYS ENP2611 MACHINE SUPPORT @@ -1372,6 +1379,7 @@ N: rockchip ARM/SAMSUNG EXYNOS ARM ARCHITECTURES M: Kukjin Kim +M: Krzysztof Kozlowski L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) L: linux-samsung-soc@vger.kernel.org (moderated for non-subscribers) S: Maintained @@ -1432,11 +1440,9 @@ F: arch/arm/boot/dts/emev2* F: arch/arm/boot/dts/r7s* F: arch/arm/boot/dts/r8a* F: arch/arm/boot/dts/sh* -F: arch/arm/configs/ape6evm_defconfig F: arch/arm/configs/armadillo800eva_defconfig F: arch/arm/configs/bockw_defconfig F: arch/arm/configs/kzm9g_defconfig -F: arch/arm/configs/mackerel_defconfig F: arch/arm/configs/marzen_defconfig F: arch/arm/configs/shmobile_defconfig F: arch/arm/include/debug/renesas-scif.S @@ -1447,9 +1453,10 @@ ARM/SOCFPGA ARCHITECTURE M: Dinh Nguyen S: Maintained F: arch/arm/mach-socfpga/ +F: arch/arm/boot/dts/socfpga* +F: arch/arm/configs/socfpga_defconfig W: http://www.rocketboards.org -T: git://git.rocketboards.org/linux-socfpga.git -T: git://git.rocketboards.org/linux-socfpga-next.git +T: git git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux.git ARM/SOCFPGA CLOCK FRAMEWORK SUPPORT M: Dinh Nguyen @@ -1828,7 +1835,7 @@ S: Supported F: drivers/spi/spi-atmel.* ATMEL SSC DRIVER -M: Bo Shen +M: Nicolas Ferre L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) S: Supported F: drivers/misc/atmel-ssc.c @@ -1937,7 +1944,7 @@ S: Maintained F: drivers/net/wireless/b43legacy/ BACKLIGHT CLASS/SUBSYSTEM -M: Jingoo Han +M: Jingoo Han M: Lee Jones S: Maintained F: drivers/video/backlight/ @@ -2124,8 +2131,9 @@ S: Supported F: drivers/net/ethernet/broadcom/bnx2x/ BROADCOM BCM281XX/BCM11XXX/BCM216XX ARM ARCHITECTURE -M: Christian Daudt M: Florian Fainelli +M: Ray Jui +M: Scott Branden L: bcm-kernel-feedback-list@broadcom.com T: git git://github.com/broadcom/mach-bcm S: Maintained @@ -2176,7 +2184,6 @@ S: Maintained F: drivers/usb/gadget/udc/bcm63xx_udc.* BROADCOM BCM7XXX ARM ARCHITECTURE -M: Marc Carino M: Brian Norris M: Gregory Fong M: Florian Fainelli @@ -2577,6 +2584,7 @@ F: include/linux/cleancache.h CLK API M: Russell King +L: linux-clk@vger.kernel.org S: Maintained F: include/linux/clk.h @@ -2637,7 +2645,7 @@ F: drivers/media/platform/coda/ COMMON CLK FRAMEWORK M: Mike Turquette M: Stephen Boyd -L: linux-kernel@vger.kernel.org +L: linux-clk@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux.git S: Maintained F: drivers/clk/ @@ -3073,10 +3081,16 @@ F: drivers/net/fddi/defxx.* DELL LAPTOP DRIVER M: Matthew Garrett +M: Pali Rohár L: platform-driver-x86@vger.kernel.org S: Maintained F: drivers/platform/x86/dell-laptop.c +DELL LAPTOP FREEFALL DRIVER +M: Pali Rohár +S: Maintained +F: drivers/platform/x86/dell-smo8800.c + DELL LAPTOP SMM DRIVER M: Guenter Roeck S: Maintained @@ -3091,6 +3105,7 @@ F: drivers/firmware/dcdbas.* DELL WMI EXTRAS DRIVER M: Matthew Garrett +M: Pali Rohár S: Maintained F: drivers/platform/x86/dell-wmi.c @@ -3278,12 +3293,6 @@ F: drivers/firmware/dmi-id.c F: drivers/firmware/dmi_scan.c F: include/linux/dmi.h -DOCKING STATION DRIVER -M: Shaohua Li -L: linux-acpi@vger.kernel.org -S: Supported -F: drivers/acpi/dock.c - DOCUMENTATION M: Jonathan Corbet L: linux-doc@vger.kernel.org @@ -3419,6 +3428,13 @@ F: drivers/gpu/drm/rcar-du/ F: drivers/gpu/drm/shmobile/ F: include/linux/platform_data/shmob_drm.h +DRM DRIVERS FOR ROCKCHIP +M: Mark Yao +L: dri-devel@lists.freedesktop.org +S: Maintained +F: drivers/gpu/drm/rockchip/ +F: Documentation/devicetree/bindings/video/rockchip* + DSBR100 USB FM RADIO DRIVER M: Alexey Klimov L: linux-media@vger.kernel.org @@ -3911,7 +3927,7 @@ F: drivers/extcon/ F: Documentation/extcon/ EXYNOS DP DRIVER -M: Jingoo Han +M: Jingoo Han L: dri-devel@lists.freedesktop.org S: Maintained F: drivers/gpu/drm/exynos/exynos_dp* @@ -4370,11 +4386,10 @@ F: fs/gfs2/ F: include/uapi/linux/gfs2_ondisk.h GIGASET ISDN DRIVERS -M: Hansjoerg Lipp -M: Tilman Schmidt +M: Paul Bolle L: gigaset307x-common@lists.sourceforge.net W: http://gigaset307x.sourceforge.net/ -S: Maintained +S: Odd Fixes F: Documentation/isdn/README.gigaset F: drivers/isdn/gigaset/ F: include/uapi/linux/gigaset_dev.h @@ -4473,7 +4488,7 @@ S: Maintained F: block/partitions/efi.* STK1160 USB VIDEO CAPTURE DRIVER -M: Ezequiel Garcia +M: Ezequiel Garcia L: linux-media@vger.kernel.org T: git git://linuxtv.org/media_tree.git S: Maintained @@ -5016,6 +5031,11 @@ W: http://industrypack.sourceforge.net S: Maintained F: drivers/ipack/ +INGENIC JZ4780 DMA Driver +M: Zubair Lutfullah Kakakhel +S: Maintained +F: drivers/dma/dma-jz4780.c + INTEGRITY MEASUREMENT ARCHITECTURE (IMA) M: Mimi Zohar M: Dmitry Kasatkin @@ -5036,17 +5056,19 @@ S: Orphan F: drivers/video/fbdev/imsttfb.c INFINIBAND SUBSYSTEM -M: Roland Dreier +M: Doug Ledford M: Sean Hefty M: Hal Rosenstock L: linux-rdma@vger.kernel.org W: http://www.openfabrics.org/ Q: http://patchwork.kernel.org/project/linux-rdma/list/ -T: git git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband.git +T: git git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma.git S: Supported F: Documentation/infiniband/ F: drivers/infiniband/ F: include/uapi/linux/if_infiniband.h +F: include/uapi/rdma/ +F: include/rdma/ INOTIFY M: John McCutchan @@ -5799,6 +5821,7 @@ F: drivers/scsi/53c700* LED SUBSYSTEM M: Bryan Wu M: Richard Purdie +M: Jacek Anaszewski L: linux-leds@vger.kernel.org T: git git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds.git S: Maintained @@ -6165,16 +6188,6 @@ Q: http://patchwork.linuxtv.org/project/linux-media/list/ S: Maintained F: drivers/media/dvb-frontends/m88rs2000* -M88TS2022 MEDIA DRIVER -M: Antti Palosaari -L: linux-media@vger.kernel.org -W: http://linuxtv.org/ -W: http://palosaari.fi/linux/ -Q: http://patchwork.linuxtv.org/project/linux-media/list/ -T: git git://linuxtv.org/anttip/media_tree.git -S: Maintained -F: drivers/media/tuners/m88ts2022* - MA901 MASTERKIT USB FM RADIO DRIVER M: Alexey Klimov L: linux-media@vger.kernel.org @@ -6598,6 +6611,7 @@ M: Laurent Pinchart L: linux-media@vger.kernel.org T: git git://linuxtv.org/media_tree.git S: Maintained +F: Documentation/devicetree/bindings/media/i2c/mt9v032.txt F: drivers/media/i2c/mt9v032.c F: include/media/mt9v032.h @@ -6953,6 +6967,17 @@ T: git git://git.rocketboards.org/linux-socfpga-next.git S: Maintained F: arch/nios2/ +NOKIA N900 POWER SUPPLY DRIVERS +M: Pali Rohár +S: Maintained +F: include/linux/power/bq2415x_charger.h +F: include/linux/power/bq27x00_battery.h +F: include/linux/power/isp1704_charger.h +F: drivers/power/bq2415x_charger.c +F: drivers/power/bq27x00_battery.c +F: drivers/power/isp1704_charger.c +F: drivers/power/rx51_battery.c + NTB DRIVER M: Jon Mason M: Dave Jiang @@ -7015,6 +7040,8 @@ Q: http://patchwork.kernel.org/project/linux-omap/list/ T: git git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git S: Maintained F: arch/arm/*omap*/ +F: arch/arm/configs/omap1_defconfig +F: arch/arm/configs/omap2plus_defconfig F: drivers/i2c/busses/i2c-omap.c F: drivers/irqchip/irq-omap-intc.c F: drivers/mfd/*omap*.c @@ -7145,6 +7172,7 @@ OMAP IMAGING SUBSYSTEM (OMAP3 ISP and OMAP4 ISS) M: Laurent Pinchart L: linux-media@vger.kernel.org S: Maintained +F: Documentation/devicetree/bindings/media/ti,omap3isp.txt F: drivers/media/platform/omap3isp/ F: drivers/staging/media/omap4iss/ @@ -7538,7 +7566,7 @@ S: Maintained F: drivers/pci/host/*rcar* PCI DRIVER FOR SAMSUNG EXYNOS -M: Jingoo Han +M: Jingoo Han L: linux-pci@vger.kernel.org L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) L: linux-samsung-soc@vger.kernel.org (moderated for non-subscribers) @@ -7546,8 +7574,7 @@ S: Maintained F: drivers/pci/host/pci-exynos.c PCI DRIVER FOR SYNOPSIS DESIGNWARE -M: Mohit Kumar -M: Jingoo Han +M: Jingoo Han L: linux-pci@vger.kernel.org S: Maintained F: drivers/pci/host/*designware* @@ -7561,9 +7588,8 @@ F: Documentation/devicetree/bindings/pci/host-generic-pci.txt F: drivers/pci/host/pci-host-generic.c PCIE DRIVER FOR ST SPEAR13XX -M: Mohit Kumar L: linux-pci@vger.kernel.org -S: Maintained +S: Orphan F: drivers/pci/host/*spear* PCMCIA SUBSYSTEM @@ -8504,7 +8530,7 @@ S: Supported F: sound/soc/samsung/ SAMSUNG FRAMEBUFFER DRIVER -M: Jingoo Han +M: Jingoo Han L: linux-fbdev@vger.kernel.org S: Maintained F: drivers/video/fbdev/s3c-fb.c @@ -8809,15 +8835,25 @@ W: http://www.emulex.com S: Supported F: drivers/scsi/be2iscsi/ -SERVER ENGINES 10Gbps NIC - BladeEngine 2 DRIVER -M: Sathya Perla -M: Subbu Seetharaman -M: Ajit Khaparde +Emulex 10Gbps NIC BE2, BE3-R, Lancer, Skyhawk-R DRIVER +M: Sathya Perla +M: Ajit Khaparde +M: Padmanabh Ratnakar +M: Sriharsha Basavapatna L: netdev@vger.kernel.org W: http://www.emulex.com S: Supported F: drivers/net/ethernet/emulex/benet/ +EMULEX ONECONNECT ROCE DRIVER +M: Selvin Xavier +M: Devesh Sharma +M: Mitesh Ahuja +L: linux-rdma@vger.kernel.org +W: http://www.emulex.com +S: Supported +F: drivers/infiniband/hw/ocrdma/ + SFC NETWORK DRIVER M: Solarflare linux maintainers M: Shradha Shah @@ -8991,6 +9027,16 @@ T: git git://linuxtv.org/mhadli/v4l-dvb-davinci_devices.git S: Maintained F: drivers/media/platform/am437x/ +OV2659 OMNIVISION SENSOR DRIVER +M: Lad, Prabhakar +L: linux-media@vger.kernel.org +W: http://linuxtv.org/ +Q: http://patchwork.linuxtv.org/project/linux-media/list/ +T: git git://linuxtv.org/mhadli/v4l-dvb-davinci_devices.git +S: Maintained +F: drivers/media/i2c/ov2659.c +F: include/media/ov2659.h + SIS 190 ETHERNET DRIVER M: Francois Romieu L: netdev@vger.kernel.org @@ -9940,10 +9986,23 @@ S: Maintained F: drivers/platform/x86/topstar-laptop.c TOSHIBA ACPI EXTRAS DRIVER +M: Azael Avalos L: platform-driver-x86@vger.kernel.org -S: Orphan +S: Maintained F: drivers/platform/x86/toshiba_acpi.c +TOSHIBA BLUETOOTH DRIVER +M: Azael Avalos +L: platform-driver-x86@vger.kernel.org +S: Maintained +F: drivers/platform/x86/toshiba_bluetooth.c + +TOSHIBA HDD ACTIVE PROTECTION SENSOR DRIVER +M: Azael Avalos +L: platform-driver-x86@vger.kernel.org +S: Maintained +F: drivers/platform/x86/toshiba_haps.c + TOSHIBA SMM DRIVER M: Jonathan Buzzard L: tlinux-users@tce.toshiba-dme.co.jp @@ -10500,7 +10559,6 @@ F: include/linux/virtio_console.h F: include/uapi/linux/virtio_console.h VIRTIO CORE, NET AND BLOCK DRIVERS -M: Rusty Russell M: "Michael S. Tsirkin" L: virtualization@lists.linux-foundation.org S: Maintained @@ -10520,6 +10578,12 @@ S: Maintained F: drivers/vhost/ F: include/uapi/linux/vhost.h +VIRTIO INPUT DRIVER +M: Gerd Hoffmann +S: Maintained +F: drivers/virtio/virtio_input.c +F: include/uapi/linux/virtio_input.h + VIA RHINE NETWORK DRIVER M: Roger Luethi S: Maintained @@ -10595,6 +10659,14 @@ L: linux-kernel@vger.kernel.org S: Maintained F: drivers/misc/vmw_balloon.c +VMWARE VMMOUSE SUBDRIVER +M: "VMware Graphics" +M: "VMware, Inc." +L: linux-input@vger.kernel.org +S: Maintained +F: drivers/input/mouse/vmmouse.c +F: drivers/input/mouse/vmmouse.h + VMWARE VMXNET3 ETHERNET DRIVER M: Shreyas Bhatewara M: "VMware, Inc." @@ -10920,6 +10992,16 @@ L: linux-serial@vger.kernel.org S: Maintained F: drivers/tty/serial/uartlite.c +XILINX VIDEO IP CORES +M: Hyun Kwon +M: Laurent Pinchart +L: linux-media@vger.kernel.org +T: git git://linuxtv.org/media_tree.git +S: Supported +F: Documentation/devicetree/bindings/media/xilinx/ +F: drivers/media/platform/xilinx/ +F: include/uapi/linux/xilinx-v4l2-controls.h + XILLYBUS DRIVER M: Eli Billauer L: linux-kernel@vger.kernel.org @@ -10984,6 +11066,7 @@ F: drivers/media/pci/zoran/ ZRAM COMPRESSED RAM BLOCK DEVICE DRVIER M: Minchan Kim M: Nitin Gupta +R: Sergey Senozhatsky L: linux-kernel@vger.kernel.org S: Maintained F: drivers/block/zram/ diff --git a/Makefile b/Makefile index 6cc5b2434224..dc20bcb9b271 100644 --- a/Makefile +++ b/Makefile @@ -1,7 +1,7 @@ VERSION = 4 -PATCHLEVEL = 0 +PATCHLEVEL = 1 SUBLEVEL = 0 -EXTRAVERSION = +EXTRAVERSION = -rc4 NAME = Hurr durr I'ma sheep # *DOCUMENTATION* diff --git a/arch/arc/Kconfig.debug b/arch/arc/Kconfig.debug index a7fc0da25650..ff6a4b5ce927 100644 --- a/arch/arc/Kconfig.debug +++ b/arch/arc/Kconfig.debug @@ -2,19 +2,6 @@ menu "Kernel hacking" source "lib/Kconfig.debug" -config EARLY_PRINTK - bool "Early printk" if EMBEDDED - default y - help - Write kernel log output directly into the VGA buffer or to a serial - port. - - This is useful for kernel debugging when your machine crashes very - early before the console code is initialized. For normal operation - it is not recommended because it looks ugly and doesn't cooperate - with klogd/syslogd or the X server. You should normally N here, - unless you want to debug such a crash. - config 16KSTACKS bool "Use 16Kb for kernel stacks instead of 8Kb" help diff --git a/arch/arc/boot/dts/angel4.dts b/arch/arc/boot/dts/angel4.dts index 757e0c62c4f9..3b076fbd8366 100644 --- a/arch/arc/boot/dts/angel4.dts +++ b/arch/arc/boot/dts/angel4.dts @@ -64,7 +64,7 @@ }; arcpmu0: pmu { - compatible = "snps,arc700-pmu"; + compatible = "snps,arc700-pct"; }; }; }; diff --git a/arch/arc/configs/nsimosci_defconfig b/arch/arc/configs/nsimosci_defconfig index 278dacf2a3f9..d2ac4e56ba1d 100644 --- a/arch/arc/configs/nsimosci_defconfig +++ b/arch/arc/configs/nsimosci_defconfig @@ -2,6 +2,9 @@ CONFIG_CROSS_COMPILE="arc-linux-uclibc-" # CONFIG_LOCALVERSION_AUTO is not set CONFIG_DEFAULT_HOSTNAME="ARCLinux" # CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +# CONFIG_CROSS_MEMORY_ATTACH is not set +CONFIG_NO_HZ=y CONFIG_HIGH_RES_TIMERS=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y @@ -9,7 +12,7 @@ CONFIG_NAMESPACES=y # CONFIG_UTS_NS is not set # CONFIG_PID_NS is not set CONFIG_BLK_DEV_INITRD=y -CONFIG_INITRAMFS_SOURCE="../arc_initramfs" +CONFIG_INITRAMFS_SOURCE="../arc_initramfs/" CONFIG_KALLSYMS_ALL=y CONFIG_EMBEDDED=y # CONFIG_SLUB_DEBUG is not set @@ -21,12 +24,9 @@ CONFIG_MODULES=y # CONFIG_IOSCHED_DEADLINE is not set # CONFIG_IOSCHED_CFQ is not set CONFIG_ARC_PLAT_FPGA_LEGACY=y -# CONFIG_ARC_IDE is not set -# CONFIG_ARCTANGENT_EMAC is not set # CONFIG_ARC_HAS_RTSC is not set CONFIG_ARC_BUILTIN_DTB_NAME="nsimosci" # CONFIG_COMPACTION is not set -# CONFIG_CROSS_MEMORY_ATTACH is not set CONFIG_NET=y CONFIG_PACKET=y CONFIG_UNIX=y @@ -39,23 +39,23 @@ CONFIG_INET=y # CONFIG_FIRMWARE_IN_KERNEL is not set # CONFIG_BLK_DEV is not set CONFIG_NETDEVICES=y -# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +# CONFIG_INPUT_MOUSEDEV is not set +CONFIG_INPUT_EVDEV=y # CONFIG_MOUSE_PS2_ALPS is not set # CONFIG_MOUSE_PS2_LOGIPS2PP is not set # CONFIG_MOUSE_PS2_SYNAPTICS is not set +# CONFIG_MOUSE_PS2_CYPRESS is not set # CONFIG_MOUSE_PS2_TRACKPOINT is not set CONFIG_MOUSE_PS2_TOUCHKIT=y -# CONFIG_SERIO_I8042 is not set # CONFIG_SERIO_SERPORT is not set CONFIG_SERIO_ARC_PS2=y # CONFIG_LEGACY_PTYS is not set # CONFIG_DEVKMEM is not set CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_DW=y +CONFIG_SERIAL_8250_NR_UARTS=1 +CONFIG_SERIAL_8250_RUNTIME_UARTS=1 CONFIG_SERIAL_OF_PLATFORM=y -CONFIG_SERIAL_ARC=y -CONFIG_SERIAL_ARC_CONSOLE=y # CONFIG_HW_RANDOM is not set # CONFIG_HWMON is not set CONFIG_FB=y @@ -72,4 +72,3 @@ CONFIG_TMPFS=y CONFIG_NFS_FS=y # CONFIG_ENABLE_WARN_DEPRECATED is not set # CONFIG_ENABLE_MUST_CHECK is not set -CONFIG_XZ_DEC=y diff --git a/arch/arc/include/asm/arcregs.h b/arch/arc/include/asm/arcregs.h index be33db8a2ee3..e2b1b1211b0d 100644 --- a/arch/arc/include/asm/arcregs.h +++ b/arch/arc/include/asm/arcregs.h @@ -30,6 +30,7 @@ #define ARC_REG_D_UNCACH_BCR 0x6A #define ARC_REG_BPU_BCR 0xc0 #define ARC_REG_ISA_CFG_BCR 0xc1 +#define ARC_REG_RTT_BCR 0xF2 #define ARC_REG_SMART_BCR 0xFF /* status32 Bits Positions */ @@ -50,11 +51,7 @@ * [15: 8] = Exception Cause Code * [ 7: 0] = Exception Parameters (for certain types only) */ -#define ECR_VEC_MASK 0xff0000 -#define ECR_CODE_MASK 0x00ff00 -#define ECR_PARAM_MASK 0x0000ff - -/* Exception Cause Vector Values */ +#define ECR_V_MEM_ERR 0x01 #define ECR_V_INSN_ERR 0x02 #define ECR_V_MACH_CHK 0x20 #define ECR_V_ITLB_MISS 0x21 @@ -62,7 +59,8 @@ #define ECR_V_PROTV 0x23 #define ECR_V_TRAP 0x25 -/* Protection Violation Exception Cause Code Values */ +/* DTLB Miss and Protection Violation Cause Codes */ + #define ECR_C_PROTV_INST_FETCH 0x00 #define ECR_C_PROTV_LOAD 0x01 #define ECR_C_PROTV_STORE 0x02 @@ -173,11 +171,11 @@ } \ } -#define WRITE_BCR(reg, into) \ +#define WRITE_AUX(reg, into) \ { \ unsigned int tmp; \ if (sizeof(tmp) == sizeof(into)) { \ - tmp = (*(unsigned int *)(into)); \ + tmp = (*(unsigned int *)&(into)); \ write_aux_reg(reg, tmp); \ } else { \ extern void bogus_undefined(void); \ diff --git a/arch/arc/include/asm/atomic.h b/arch/arc/include/asm/atomic.h index 067551b6920a..9917a45fc430 100644 --- a/arch/arc/include/asm/atomic.h +++ b/arch/arc/include/asm/atomic.h @@ -99,7 +99,7 @@ static inline void atomic_##op(int i, atomic_t *v) \ atomic_ops_unlock(flags); \ } -#define ATOMIC_OP_RETURN(op, c_op) \ +#define ATOMIC_OP_RETURN(op, c_op, asm_op) \ static inline int atomic_##op##_return(int i, atomic_t *v) \ { \ unsigned long flags; \ diff --git a/arch/arc/include/asm/bitops.h b/arch/arc/include/asm/bitops.h index 1a5bf07eefe2..4051e9525939 100644 --- a/arch/arc/include/asm/bitops.h +++ b/arch/arc/include/asm/bitops.h @@ -32,6 +32,20 @@ static inline void set_bit(unsigned long nr, volatile unsigned long *m) m += nr >> 5; + /* + * ARC ISA micro-optimization: + * + * Instructions dealing with bitpos only consider lower 5 bits (0-31) + * e.g (x << 33) is handled like (x << 1) by ASL instruction + * (mem pointer still needs adjustment to point to next word) + * + * Hence the masking to clamp @nr arg can be elided in general. + * + * However if @nr is a constant (above assumed it in a register), + * and greater than 31, gcc can optimize away (x << 33) to 0, + * as overflow, given the 32-bit ISA. Thus masking needs to be done + * for constant @nr, but no code is generated due to const prop. + */ if (__builtin_constant_p(nr)) nr &= 0x1f; @@ -374,29 +388,20 @@ __test_and_change_bit(unsigned long nr, volatile unsigned long *m) * This routine doesn't need to be atomic. */ static inline int -__constant_test_bit(unsigned int nr, const volatile unsigned long *addr) -{ - return ((1UL << (nr & 31)) & - (((const volatile unsigned int *)addr)[nr >> 5])) != 0; -} - -static inline int -__test_bit(unsigned int nr, const volatile unsigned long *addr) +test_bit(unsigned int nr, const volatile unsigned long *addr) { unsigned long mask; addr += nr >> 5; - /* ARC700 only considers 5 bits in bit-fiddling insn */ + if (__builtin_constant_p(nr)) + nr &= 0x1f; + mask = 1 << nr; return ((mask & *addr) != 0); } -#define test_bit(nr, addr) (__builtin_constant_p(nr) ? \ - __constant_test_bit((nr), (addr)) : \ - __test_bit((nr), (addr))) - /* * Count the number of zeros, starting from MSB * Helper for fls( ) friends diff --git a/arch/arc/include/asm/perf_event.h b/arch/arc/include/asm/perf_event.h index cbf755e32a03..2b8880e953a2 100644 --- a/arch/arc/include/asm/perf_event.h +++ b/arch/arc/include/asm/perf_event.h @@ -54,29 +54,13 @@ struct arc_reg_cc_build { #define PERF_COUNT_ARC_BPOK (PERF_COUNT_HW_MAX + 3) #define PERF_COUNT_ARC_EDTLB (PERF_COUNT_HW_MAX + 4) #define PERF_COUNT_ARC_EITLB (PERF_COUNT_HW_MAX + 5) -#define PERF_COUNT_ARC_HW_MAX (PERF_COUNT_HW_MAX + 6) +#define PERF_COUNT_ARC_LDC (PERF_COUNT_HW_MAX + 6) +#define PERF_COUNT_ARC_STC (PERF_COUNT_HW_MAX + 7) + +#define PERF_COUNT_ARC_HW_MAX (PERF_COUNT_HW_MAX + 8) /* - * The "generalized" performance events seem to really be a copy - * of the available events on x86 processors; the mapping to ARC - * events is not always possible 1-to-1. Fortunately, there doesn't - * seem to be an exact definition for these events, so we can cheat - * a bit where necessary. - * - * In particular, the following PERF events may behave a bit differently - * compared to other architectures: - * - * PERF_COUNT_HW_CPU_CYCLES - * Cycles not in halted state - * - * PERF_COUNT_HW_REF_CPU_CYCLES - * Reference cycles not in halted state, same as PERF_COUNT_HW_CPU_CYCLES - * for now as we don't do Dynamic Voltage/Frequency Scaling (yet) - * - * PERF_COUNT_HW_BUS_CYCLES - * Unclear what this means, Intel uses 0x013c, which according to - * their datasheet means "unhalted reference cycles". It sounds similar - * to PERF_COUNT_HW_REF_CPU_CYCLES, and we use the same counter for it. + * Some ARC pct quirks: * * PERF_COUNT_HW_STALLED_CYCLES_BACKEND * PERF_COUNT_HW_STALLED_CYCLES_FRONTEND @@ -91,21 +75,38 @@ struct arc_reg_cc_build { * Note that I$ cache misses aren't counted by either of the two! */ +/* + * ARC PCT has hardware conditions with fixed "names" but variable "indexes" + * (based on a specific RTL build) + * Below is the static map between perf generic/arc specific event_id and + * h/w condition names. + * At the time of probe, we loop thru each index and find it's name to + * complete the mapping of perf event_id to h/w index as latter is needed + * to program the counter really + */ static const char * const arc_pmu_ev_hw_map[] = { + /* count cycles */ [PERF_COUNT_HW_CPU_CYCLES] = "crun", [PERF_COUNT_HW_REF_CPU_CYCLES] = "crun", [PERF_COUNT_HW_BUS_CYCLES] = "crun", - [PERF_COUNT_HW_INSTRUCTIONS] = "iall", - [PERF_COUNT_HW_BRANCH_MISSES] = "bpfail", - [PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = "ijmp", + [PERF_COUNT_HW_STALLED_CYCLES_FRONTEND] = "bflush", [PERF_COUNT_HW_STALLED_CYCLES_BACKEND] = "bstall", - [PERF_COUNT_ARC_DCLM] = "dclm", - [PERF_COUNT_ARC_DCSM] = "dcsm", - [PERF_COUNT_ARC_ICM] = "icm", - [PERF_COUNT_ARC_BPOK] = "bpok", - [PERF_COUNT_ARC_EDTLB] = "edtlb", - [PERF_COUNT_ARC_EITLB] = "eitlb", + + /* counts condition */ + [PERF_COUNT_HW_INSTRUCTIONS] = "iall", + [PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = "ijmp", + [PERF_COUNT_ARC_BPOK] = "bpok", /* NP-NT, PT-T, PNT-NT */ + [PERF_COUNT_HW_BRANCH_MISSES] = "bpfail", /* NP-T, PT-NT, PNT-T */ + + [PERF_COUNT_ARC_LDC] = "imemrdc", /* Instr: mem read cached */ + [PERF_COUNT_ARC_STC] = "imemwrc", /* Instr: mem write cached */ + + [PERF_COUNT_ARC_DCLM] = "dclm", /* D-cache Load Miss */ + [PERF_COUNT_ARC_DCSM] = "dcsm", /* D-cache Store Miss */ + [PERF_COUNT_ARC_ICM] = "icm", /* I-cache Miss */ + [PERF_COUNT_ARC_EDTLB] = "edtlb", /* D-TLB Miss */ + [PERF_COUNT_ARC_EITLB] = "eitlb", /* I-TLB Miss */ }; #define C(_x) PERF_COUNT_HW_CACHE_##_x @@ -114,11 +115,11 @@ static const char * const arc_pmu_ev_hw_map[] = { static const unsigned arc_pmu_cache_map[C(MAX)][C(OP_MAX)][C(RESULT_MAX)] = { [C(L1D)] = { [C(OP_READ)] = { - [C(RESULT_ACCESS)] = CACHE_OP_UNSUPPORTED, + [C(RESULT_ACCESS)] = PERF_COUNT_ARC_LDC, [C(RESULT_MISS)] = PERF_COUNT_ARC_DCLM, }, [C(OP_WRITE)] = { - [C(RESULT_ACCESS)] = CACHE_OP_UNSUPPORTED, + [C(RESULT_ACCESS)] = PERF_COUNT_ARC_STC, [C(RESULT_MISS)] = PERF_COUNT_ARC_DCSM, }, [C(OP_PREFETCH)] = { @@ -128,7 +129,7 @@ static const unsigned arc_pmu_cache_map[C(MAX)][C(OP_MAX)][C(RESULT_MAX)] = { }, [C(L1I)] = { [C(OP_READ)] = { - [C(RESULT_ACCESS)] = CACHE_OP_UNSUPPORTED, + [C(RESULT_ACCESS)] = PERF_COUNT_HW_INSTRUCTIONS, [C(RESULT_MISS)] = PERF_COUNT_ARC_ICM, }, [C(OP_WRITE)] = { @@ -156,9 +157,10 @@ static const unsigned arc_pmu_cache_map[C(MAX)][C(OP_MAX)][C(RESULT_MAX)] = { }, [C(DTLB)] = { [C(OP_READ)] = { - [C(RESULT_ACCESS)] = CACHE_OP_UNSUPPORTED, + [C(RESULT_ACCESS)] = PERF_COUNT_ARC_LDC, [C(RESULT_MISS)] = PERF_COUNT_ARC_EDTLB, }, + /* DTLB LD/ST Miss not segregated by h/w*/ [C(OP_WRITE)] = { [C(RESULT_ACCESS)] = CACHE_OP_UNSUPPORTED, [C(RESULT_MISS)] = CACHE_OP_UNSUPPORTED, diff --git a/arch/arc/kernel/perf_event.c b/arch/arc/kernel/perf_event.c index ae1c485cbc68..fd2ec50102f2 100644 --- a/arch/arc/kernel/perf_event.c +++ b/arch/arc/kernel/perf_event.c @@ -16,6 +16,7 @@ #include #include #include +#include struct arc_pmu { struct pmu pmu; @@ -25,6 +26,46 @@ struct arc_pmu { int ev_hw_idx[PERF_COUNT_ARC_HW_MAX]; }; +struct arc_callchain_trace { + int depth; + void *perf_stuff; +}; + +static int callchain_trace(unsigned int addr, void *data) +{ + struct arc_callchain_trace *ctrl = data; + struct perf_callchain_entry *entry = ctrl->perf_stuff; + perf_callchain_store(entry, addr); + + if (ctrl->depth++ < 3) + return 0; + + return -1; +} + +void +perf_callchain_kernel(struct perf_callchain_entry *entry, struct pt_regs *regs) +{ + struct arc_callchain_trace ctrl = { + .depth = 0, + .perf_stuff = entry, + }; + + arc_unwind_core(NULL, regs, callchain_trace, &ctrl); +} + +void +perf_callchain_user(struct perf_callchain_entry *entry, struct pt_regs *regs) +{ + /* + * User stack can't be unwound trivially with kernel dwarf unwinder + * So for now just record the user PC + */ + perf_callchain_store(entry, instruction_pointer(regs)); +} + +static struct arc_pmu *arc_pmu; + /* read counter #idx; note that counter# != event# on ARC! */ static uint64_t arc_pmu_read_counter(int idx) { @@ -47,7 +88,6 @@ static uint64_t arc_pmu_read_counter(int idx) static void arc_perf_event_update(struct perf_event *event, struct hw_perf_event *hwc, int idx) { - struct arc_pmu *arc_pmu = container_of(event->pmu, struct arc_pmu, pmu); uint64_t prev_raw_count, new_raw_count; int64_t delta; @@ -89,13 +129,16 @@ static int arc_pmu_cache_event(u64 config) if (ret == CACHE_OP_UNSUPPORTED) return -ENOENT; + pr_debug("init cache event: type/op/result %d/%d/%d with h/w %d \'%s\'\n", + cache_type, cache_op, cache_result, ret, + arc_pmu_ev_hw_map[ret]); + return ret; } /* initializes hw_perf_event structure if event is supported */ static int arc_pmu_event_init(struct perf_event *event) { - struct arc_pmu *arc_pmu = container_of(event->pmu, struct arc_pmu, pmu); struct hw_perf_event *hwc = &event->hw; int ret; @@ -106,8 +149,9 @@ static int arc_pmu_event_init(struct perf_event *event) if (arc_pmu->ev_hw_idx[event->attr.config] < 0) return -ENOENT; hwc->config = arc_pmu->ev_hw_idx[event->attr.config]; - pr_debug("initializing event %d with cfg %d\n", - (int) event->attr.config, (int) hwc->config); + pr_debug("init event %d with h/w %d \'%s\'\n", + (int) event->attr.config, (int) hwc->config, + arc_pmu_ev_hw_map[event->attr.config]); return 0; case PERF_TYPE_HW_CACHE: ret = arc_pmu_cache_event(event->attr.config); @@ -183,8 +227,6 @@ static void arc_pmu_stop(struct perf_event *event, int flags) static void arc_pmu_del(struct perf_event *event, int flags) { - struct arc_pmu *arc_pmu = container_of(event->pmu, struct arc_pmu, pmu); - arc_pmu_stop(event, PERF_EF_UPDATE); __clear_bit(event->hw.idx, arc_pmu->used_mask); @@ -194,7 +236,6 @@ static void arc_pmu_del(struct perf_event *event, int flags) /* allocate hardware counter and optionally start counting */ static int arc_pmu_add(struct perf_event *event, int flags) { - struct arc_pmu *arc_pmu = container_of(event->pmu, struct arc_pmu, pmu); struct hw_perf_event *hwc = &event->hw; int idx = hwc->idx; @@ -247,10 +288,7 @@ static int arc_pmu_device_probe(struct platform_device *pdev) BUG_ON(pct_bcr.c > ARC_PMU_MAX_HWEVENTS); READ_BCR(ARC_REG_CC_BUILD, cc_bcr); - if (!cc_bcr.v) { - pr_err("Performance counters exist, but no countable conditions?\n"); - return -ENODEV; - } + BUG_ON(!cc_bcr.v); /* Counters exist but No countable conditions ? */ arc_pmu = devm_kzalloc(&pdev->dev, sizeof(struct arc_pmu), GFP_KERNEL); if (!arc_pmu) @@ -263,19 +301,22 @@ static int arc_pmu_device_probe(struct platform_device *pdev) arc_pmu->n_counters, arc_pmu->counter_size, cc_bcr.c); cc_name.str[8] = 0; - for (i = 0; i < PERF_COUNT_HW_MAX; i++) + for (i = 0; i < PERF_COUNT_ARC_HW_MAX; i++) arc_pmu->ev_hw_idx[i] = -1; + /* loop thru all available h/w condition indexes */ for (j = 0; j < cc_bcr.c; j++) { write_aux_reg(ARC_REG_CC_INDEX, j); cc_name.indiv.word0 = read_aux_reg(ARC_REG_CC_NAME0); cc_name.indiv.word1 = read_aux_reg(ARC_REG_CC_NAME1); + + /* See if it has been mapped to a perf event_id */ for (i = 0; i < ARRAY_SIZE(arc_pmu_ev_hw_map); i++) { if (arc_pmu_ev_hw_map[i] && !strcmp(arc_pmu_ev_hw_map[i], cc_name.str) && strlen(arc_pmu_ev_hw_map[i])) { - pr_debug("mapping %d to idx %d with name %s\n", - i, j, cc_name.str); + pr_debug("mapping perf event %2d to h/w event \'%8s\' (idx %d)\n", + i, cc_name.str, j); arc_pmu->ev_hw_idx[i] = j; } } @@ -302,7 +343,7 @@ static int arc_pmu_device_probe(struct platform_device *pdev) #ifdef CONFIG_OF static const struct of_device_id arc_pmu_match[] = { - { .compatible = "snps,arc700-pmu" }, + { .compatible = "snps,arc700-pct" }, {}, }; MODULE_DEVICE_TABLE(of, arc_pmu_match); @@ -310,7 +351,7 @@ MODULE_DEVICE_TABLE(of, arc_pmu_match); static struct platform_driver arc_pmu_driver = { .driver = { - .name = "arc700-pmu", + .name = "arc700-pct", .of_match_table = of_match_ptr(arc_pmu_match), }, .probe = arc_pmu_device_probe, diff --git a/arch/arc/kernel/process.c b/arch/arc/kernel/process.c index f46efd14059d..e095c557afdd 100644 --- a/arch/arc/kernel/process.c +++ b/arch/arc/kernel/process.c @@ -49,7 +49,10 @@ void arch_cpu_idle(void) asmlinkage void ret_from_fork(void); -/* Layout of Child kernel mode stack as setup at the end of this function is +/* + * Copy architecture-specific thread state + * + * Layout of Child kernel mode stack as setup at the end of this function is * * | ... | * | ... | @@ -81,7 +84,7 @@ asmlinkage void ret_from_fork(void); * ------------------ <===== END of PAGE */ int copy_thread(unsigned long clone_flags, - unsigned long usp, unsigned long arg, + unsigned long usp, unsigned long kthread_arg, struct task_struct *p) { struct pt_regs *c_regs; /* child's pt_regs */ @@ -112,7 +115,7 @@ int copy_thread(unsigned long clone_flags, if (unlikely(p->flags & PF_KTHREAD)) { memset(c_regs, 0, sizeof(struct pt_regs)); - c_callee->r13 = arg; /* argument to kernel thread */ + c_callee->r13 = kthread_arg; c_callee->r14 = usp; /* function */ return 0; diff --git a/arch/arc/kernel/setup.c b/arch/arc/kernel/setup.c index 900f68a70088..1d167c6df8ca 100644 --- a/arch/arc/kernel/setup.c +++ b/arch/arc/kernel/setup.c @@ -120,7 +120,10 @@ static void read_arc_build_cfg_regs(void) READ_BCR(ARC_REG_SMART_BCR, bcr); cpu->extn.smart = bcr.ver ? 1 : 0; - cpu->extn.debug = cpu->extn.ap | cpu->extn.smart; + READ_BCR(ARC_REG_RTT_BCR, bcr); + cpu->extn.rtt = bcr.ver ? 1 : 0; + + cpu->extn.debug = cpu->extn.ap | cpu->extn.smart | cpu->extn.rtt; } static const struct cpuinfo_data arc_cpu_tbl[] = { diff --git a/arch/arc/kernel/traps.c b/arch/arc/kernel/traps.c index 3eadfdabc322..c927aa84e652 100644 --- a/arch/arc/kernel/traps.c +++ b/arch/arc/kernel/traps.c @@ -42,7 +42,7 @@ void die(const char *str, struct pt_regs *regs, unsigned long address) * -for kernel, chk if due to copy_(to|from)_user, otherwise die() */ static noinline int -handle_exception(const char *str, struct pt_regs *regs, siginfo_t *info) +unhandled_exception(const char *str, struct pt_regs *regs, siginfo_t *info) { if (user_mode(regs)) { struct task_struct *tsk = current; @@ -71,7 +71,7 @@ int name(unsigned long address, struct pt_regs *regs) \ .si_code = sicode, \ .si_addr = (void __user *)address, \ }; \ - return handle_exception(str, regs, &info);\ + return unhandled_exception(str, regs, &info);\ } /* diff --git a/arch/arc/mm/cache_arc700.c b/arch/arc/mm/cache_arc700.c index 8c3a3e02ba92..12b2100db073 100644 --- a/arch/arc/mm/cache_arc700.c +++ b/arch/arc/mm/cache_arc700.c @@ -266,7 +266,7 @@ static inline void __cache_line_loop(unsigned long paddr, unsigned long vaddr, * Machine specific helpers for Entire D-Cache or Per Line ops */ -static unsigned int __before_dc_op(const int op) +static inline unsigned int __before_dc_op(const int op) { unsigned int reg = reg; @@ -284,7 +284,7 @@ static unsigned int __before_dc_op(const int op) return reg; } -static void __after_dc_op(const int op, unsigned int reg) +static inline void __after_dc_op(const int op, unsigned int reg) { if (op & OP_FLUSH) /* flush / flush-n-inv both wait */ while (read_aux_reg(ARC_REG_DC_CTRL) & DC_CTRL_FLUSH_STATUS); diff --git a/arch/arc/mm/init.c b/arch/arc/mm/init.c index 523412369f70..d44eedd8c322 100644 --- a/arch/arc/mm/init.c +++ b/arch/arc/mm/init.c @@ -71,7 +71,7 @@ early_param("initrd", early_initrd); */ void __init setup_arch_memory(void) { - unsigned long zones_size[MAX_NR_ZONES] = { 0, 0 }; + unsigned long zones_size[MAX_NR_ZONES]; unsigned long end_mem = CONFIG_LINUX_LINK_BASE + arc_mem_sz; init_mm.start_code = (unsigned long)_text; @@ -90,7 +90,7 @@ void __init setup_arch_memory(void) /*------------- externs in mm need setting up ---------------*/ /* first page of system - kernel .vector starts here */ - min_low_pfn = PFN_DOWN(CONFIG_LINUX_LINK_BASE); + min_low_pfn = ARCH_PFN_OFFSET; /* Last usable page of low mem (no HIGHMEM yet for ARC port) */ max_low_pfn = max_pfn = PFN_DOWN(end_mem); @@ -111,7 +111,7 @@ void __init setup_arch_memory(void) /*-------------- node setup --------------------------------*/ memset(zones_size, 0, sizeof(zones_size)); - zones_size[ZONE_NORMAL] = max_low_pfn - min_low_pfn; + zones_size[ZONE_NORMAL] = max_mapnr; /* * We can't use the helper free_area_init(zones[]) because it uses @@ -123,6 +123,8 @@ void __init setup_arch_memory(void) zones_size, /* num pages per zone */ min_low_pfn, /* first pfn of node */ NULL); /* NO holes */ + + high_memory = (void *)end_mem; } /* @@ -133,7 +135,6 @@ void __init setup_arch_memory(void) */ void __init mem_init(void) { - high_memory = (void *)(CONFIG_LINUX_LINK_BASE + arc_mem_sz); free_all_bootmem(); mem_init_print_info(NULL); } diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 392e7ae69452..45df48ba0b12 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -362,19 +362,6 @@ config ARCH_VERSATILE help This enables support for ARM Ltd Versatile board. -config ARCH_AT91 - bool "Atmel AT91" - select ARCH_REQUIRE_GPIOLIB - select CLKDEV_LOOKUP - select IRQ_DOMAIN - select NEED_MACH_IO_H if PCCARD - select PINCTRL - select PINCTRL_AT91 - select USE_OF - help - This enables support for systems based on Atmel - AT91RM9200, AT91SAM9 and SAMA5 processors. - config ARCH_CLPS711X bool "Cirrus Logic CLPS711x/EP721x/EP731x-based" select ARCH_REQUIRE_GPIOLIB @@ -632,18 +619,6 @@ config ARCH_PXA help Support for Intel/Marvell's PXA2xx/PXA3xx processor line. -config ARCH_MSM - bool "Qualcomm MSM (non-multiplatform)" - select ARCH_REQUIRE_GPIOLIB - select COMMON_CLK - select GENERIC_CLOCKEVENTS - help - Support for Qualcomm MSM/QSD based systems. This runs on the - apps processor of the MSM/QSD and depends on a shared memory - interface to the modem processor which runs the baseband - stack and controls some vital subsystems - (clock and power control, etc). - config ARCH_SHMOBILE_LEGACY bool "Renesas ARM SoCs (non-multiplatform)" select ARCH_SHMOBILE @@ -653,7 +628,6 @@ config ARCH_SHMOBILE_LEGACY select GENERIC_CLOCKEVENTS select HAVE_ARM_SCU if SMP select HAVE_ARM_TWD if SMP - select HAVE_MACH_CLKDEV select HAVE_SMP select MIGHT_HAVE_CACHE_L2X0 select MULTI_IRQ_HANDLER @@ -851,6 +825,8 @@ config ARCH_VIRT # source "arch/arm/mach-mvebu/Kconfig" +source "arch/arm/mach-alpine/Kconfig" + source "arch/arm/mach-asm9260/Kconfig" source "arch/arm/mach-at91/Kconfig" @@ -897,8 +873,6 @@ source "arch/arm/mach-ks8695/Kconfig" source "arch/arm/mach-meson/Kconfig" -source "arch/arm/mach-msm/Kconfig" - source "arch/arm/mach-moxart/Kconfig" source "arch/arm/mach-mv78xx0/Kconfig" @@ -1523,7 +1497,7 @@ config HZ_FIXED int default 200 if ARCH_EBSA110 || ARCH_S3C24XX || \ ARCH_S5PV210 || ARCH_EXYNOS4 - default AT91_TIMER_HZ if ARCH_AT91 + default 128 if SOC_AT91RM9200 default SHMOBILE_TIMER_HZ if ARCH_SHMOBILE_LEGACY default 0 @@ -1856,35 +1830,6 @@ config ZBOOT_ROM Say Y here if you intend to execute your compressed kernel image (zImage) directly from ROM or flash. If unsure, say N. -choice - prompt "Include SD/MMC loader in zImage (EXPERIMENTAL)" - depends on ZBOOT_ROM && ARCH_SH7372 - default ZBOOT_ROM_NONE - help - Include experimental SD/MMC loading code in the ROM-able zImage. - With this enabled it is possible to write the ROM-able zImage - kernel image to an MMC or SD card and boot the kernel straight - from the reset vector. At reset the processor Mask ROM will load - the first part of the ROM-able zImage which in turn loads the - rest the kernel image to RAM. - -config ZBOOT_ROM_NONE - bool "No SD/MMC loader in zImage (EXPERIMENTAL)" - help - Do not load image from SD or MMC - -config ZBOOT_ROM_MMCIF - bool "Include MMCIF loader in zImage (EXPERIMENTAL)" - help - Load image from MMCIF hardware block. - -config ZBOOT_ROM_SH_MOBILE_SDHI - bool "Include SuperH Mobile SDHI loader in zImage (EXPERIMENTAL)" - help - Load image from SDHI hardware block - -endchoice - config ARM_APPENDED_DTB bool "Use appended device tree blob to zImage (EXPERIMENTAL)" depends on OF @@ -2158,6 +2103,8 @@ source "net/Kconfig" source "drivers/Kconfig" +source "drivers/firmware/Kconfig" + source "fs/Kconfig" source "arch/arm/Kconfig.debug" diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index 970de7518341..0c12ffb155a2 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -93,6 +93,14 @@ choice prompt "Kernel low-level debugging port" depends on DEBUG_LL + config DEBUG_ALPINE_UART0 + bool "Kernel low-level debugging messages via Alpine UART0" + depends on ARCH_ALPINE + select DEBUG_UART_8250 + help + Say Y here if you want kernel low-level debugging support + on Alpine based platforms. + config DEBUG_ASM9260_UART bool "Kernel low-level debugging via asm9260 UART" depends on MACH_ASM9260 @@ -448,25 +456,6 @@ choice Say Y here if you want kernel low-level debugging support on MMP UART3. - config DEBUG_MSM_UART - bool "Kernel low-level debugging messages via MSM UART" - depends on ARCH_MSM - help - Say Y here if you want the debug print routines to direct - their output to the serial port on MSM devices. - - ARCH DEBUG_UART_PHYS DEBUG_UART_VIRT # - MSM7X00A, QSD8X50 0xa9a00000 0xe1000000 UART1 - MSM7X00A, QSD8X50 0xa9b00000 0xe1000000 UART2 - MSM7X00A, QSD8X50 0xa9c00000 0xe1000000 UART3 - - MSM7X30 0xaca00000 0xe1000000 UART1 - MSM7X30 0xacb00000 0xe1000000 UART2 - MSM7X30 0xacc00000 0xe1000000 UART3 - - Please adjust DEBUG_UART_PHYS and DEBUG_UART_BASE configuration - options based on your needs. - config DEBUG_QCOM_UARTDM bool "Kernel low-level debugging messages via QCOM UARTDM" depends on ARCH_QCOM @@ -806,7 +795,7 @@ choice via SCIF2 on Renesas R-Car H1 (R8A7779). config DEBUG_RCAR_GEN2_SCIF0 - bool "Kernel low-level debugging messages via SCIF0 on R8A7790/R8A7791/R8A7793)" + bool "Kernel low-level debugging messages via SCIF0 on R8A7790/R8A7791/R8A7793" depends on ARCH_R8A7790 || ARCH_R8A7791 || ARCH_R8A7793 help Say Y here if you want kernel low-level debugging support @@ -821,12 +810,11 @@ choice via SCIF2 on Renesas R-Car E2 (R8A7794). config DEBUG_RMOBILE_SCIFA0 - bool "Kernel low-level debugging messages via SCIFA0 on R8A73A4/SH7372" - depends on ARCH_R8A73A4 || ARCH_SH7372 + bool "Kernel low-level debugging messages via SCIFA0 on R8A73A4" + depends on ARCH_R8A73A4 help Say Y here if you want kernel low-level debugging support - via SCIFA0 on Renesas R-Mobile APE6 (R8A73A4) or SH-Mobile - AP4 (SH7372). + via SCIFA0 on Renesas R-Mobile APE6 (R8A73A4). config DEBUG_RMOBILE_SCIFA1 bool "Kernel low-level debugging messages via SCIFA1 on R8A7740" @@ -1295,7 +1283,7 @@ config DEBUG_LL_INCLUDE DEBUG_IMX6SL_UART || \ DEBUG_IMX6SX_UART default "debug/ks8695.S" if DEBUG_KS8695_UART - default "debug/msm.S" if DEBUG_MSM_UART || DEBUG_QCOM_UARTDM + default "debug/msm.S" if DEBUG_QCOM_UARTDM default "debug/netx.S" if DEBUG_NETX_UART default "debug/omap2plus.S" if DEBUG_OMAP2PLUS_UART default "debug/renesas-scif.S" if DEBUG_R7S72100_SCIF2 @@ -1388,7 +1376,6 @@ config DEBUG_UART_PHYS default 0x80230000 if DEBUG_PICOXCELL_UART default 0x808c0000 if ARCH_EP93XX default 0x90020000 if DEBUG_NSPIRE_CLASSIC_UART || DEBUG_NSPIRE_CX_UART - default 0xa9a00000 if DEBUG_MSM_UART default 0xb0060000 if DEBUG_SIRFPRIMA2_UART1 default 0xb0090000 if DEBUG_VEXPRESS_UART0_CRX default 0xc0013000 if DEBUG_U300_UART @@ -1417,6 +1404,7 @@ config DEBUG_UART_PHYS default 0xf8b00000 if DEBUG_HIX5HD2_UART default 0xf991e000 if DEBUG_QCOM_UARTDM default 0xfcb00000 if DEBUG_HI3620_UART + default 0xfd883000 if DEBUG_ALPINE_UART0 default 0xfe800000 if ARCH_IOP32X default 0xff690000 if DEBUG_RK32_UART2 default 0xffc02000 if DEBUG_SOCFPGA_UART @@ -1433,7 +1421,7 @@ config DEBUG_UART_PHYS DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \ DEBUG_LL_UART_EFM32 || \ DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_MESON_UARTAO || \ - DEBUG_MSM_UART || DEBUG_NETX_UART || \ + DEBUG_NETX_UART || \ DEBUG_QCOM_UARTDM || DEBUG_R7S72100_SCIF2 || \ DEBUG_RCAR_GEN1_SCIF0 || DEBUG_RCAR_GEN1_SCIF2 || \ DEBUG_RCAR_GEN2_SCIF0 || DEBUG_RCAR_GEN2_SCIF2 || \ @@ -1446,7 +1434,6 @@ config DEBUG_UART_VIRT hex "Virtual base address of debug UART" default 0xe0000a00 if DEBUG_NETX_UART default 0xe0010fe0 if ARCH_RPC - default 0xe1000000 if DEBUG_MSM_UART default 0xf0000be0 if ARCH_EBSA110 default 0xf0010000 if DEBUG_ASM9260_UART default 0xf01fb000 if DEBUG_NOMADIK_UART @@ -1483,6 +1470,7 @@ config DEBUG_UART_VIRT default 0xfd000000 if ARCH_SPEAR3XX || ARCH_SPEAR6XX default 0xfd000000 if ARCH_SPEAR13XX default 0xfd012000 if ARCH_MV78XX0 + default 0xfd883000 if DEBUG_ALPINE_UART0 default 0xfde12000 if ARCH_DOVE default 0xfe012000 if ARCH_ORION5X default 0xf31004c0 if DEBUG_MESON_UARTAO @@ -1526,7 +1514,7 @@ config DEBUG_UART_VIRT default DEBUG_UART_PHYS if !MMU depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \ DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_MESON_UARTAO || \ - DEBUG_MSM_UART || DEBUG_NETX_UART || \ + DEBUG_NETX_UART || \ DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART || \ DEBUG_UART_BCM63XX || DEBUG_ASM9260_UART || \ DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0 @@ -1543,7 +1531,7 @@ config DEBUG_UART_8250_WORD depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250 depends on DEBUG_UART_8250_SHIFT >= 2 default y if DEBUG_PICOXCELL_UART || DEBUG_SOCFPGA_UART || \ - ARCH_KEYSTONE || \ + ARCH_KEYSTONE || DEBUG_ALPINE_UART0 || \ DEBUG_DAVINCI_DMx_UART0 || DEBUG_DAVINCI_DA8XX_UART1 || \ DEBUG_DAVINCI_DA8XX_UART2 || \ DEBUG_BCM_KONA_UART || DEBUG_RK32_UART2 || \ @@ -1556,7 +1544,7 @@ config DEBUG_UART_8250_FLOW_CONTROL config DEBUG_UNCOMPRESS bool - depends on ARCH_MULTIPLATFORM || ARCH_MSM || PLAT_SAMSUNG + depends on ARCH_MULTIPLATFORM || PLAT_SAMSUNG default y if DEBUG_LL && !DEBUG_OMAP2PLUS_UART && \ (!DEBUG_TEGRA_UART || !ZBOOT_ROM) help @@ -1573,7 +1561,8 @@ config DEBUG_UNCOMPRESS config UNCOMPRESS_INCLUDE string default "debug/uncompress.h" if ARCH_MULTIPLATFORM || ARCH_MSM || \ - PLAT_SAMSUNG || ARCH_EFM32 + PLAT_SAMSUNG || ARCH_EFM32 || \ + ARCH_SHMOBILE_LEGACY default "mach/uncompress.h" config EARLY_PRINTK @@ -1610,59 +1599,6 @@ config DEBUG_SET_MODULE_RONX against certain classes of kernel exploits. If in doubt, say "N". -menuconfig CORESIGHT - bool "CoreSight Tracing Support" - select ARM_AMBA - help - This framework provides a kernel interface for the CoreSight debug - and trace drivers to register themselves with. It's intended to build - a topological view of the CoreSight components based on a DT - specification and configure the right serie of components when a - trace source gets enabled. +source "drivers/hwtracing/coresight/Kconfig" -if CORESIGHT -config CORESIGHT_LINKS_AND_SINKS - bool "CoreSight Link and Sink drivers" - help - This enables support for CoreSight link and sink drivers that are - responsible for transporting and collecting the trace data - respectively. Link and sinks are dynamically aggregated with a trace - entity at run time to form a complete trace path. - -config CORESIGHT_LINK_AND_SINK_TMC - bool "Coresight generic TMC driver" - depends on CORESIGHT_LINKS_AND_SINKS - help - This enables support for the Trace Memory Controller driver. Depending - on its configuration the device can act as a link (embedded trace router - - ETR) or sink (embedded trace FIFO). The driver complies with the - generic implementation of the component without special enhancement or - added features. - -config CORESIGHT_SINK_TPIU - bool "Coresight generic TPIU driver" - depends on CORESIGHT_LINKS_AND_SINKS - help - This enables support for the Trace Port Interface Unit driver, responsible - for bridging the gap between the on-chip coresight components and a trace - port collection engine, typically connected to an external host for use - case capturing more traces than the on-board coresight memory can handle. - -config CORESIGHT_SINK_ETBV10 - bool "Coresight ETBv1.0 driver" - depends on CORESIGHT_LINKS_AND_SINKS - help - This enables support for the Embedded Trace Buffer version 1.0 driver - that complies with the generic implementation of the component without - special enhancement or added features. - -config CORESIGHT_SOURCE_ETM3X - bool "CoreSight Embedded Trace Macrocell 3.x driver" - select CORESIGHT_LINKS_AND_SINKS - help - This driver provides support for processor ETM3.x and PTM1.x modules, - which allows tracing the instructions that a processor is executing - This is primarily useful for instruction level tracing. Depending - the ETM version data tracing may also be available. -endif endmenu diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 5575d9fa8806..985227cbbd1b 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -136,13 +136,13 @@ textofs-$(CONFIG_PM_H1940) := 0x00108000 ifeq ($(CONFIG_ARCH_SA1100),y) textofs-$(CONFIG_SA1111) := 0x00208000 endif -textofs-$(CONFIG_ARCH_MSM7X30) := 0x00208000 textofs-$(CONFIG_ARCH_MSM8X60) := 0x00208000 textofs-$(CONFIG_ARCH_MSM8960) := 0x00208000 textofs-$(CONFIG_ARCH_AXXIA) := 0x00308000 # Machine directory name. This list is sorted alphanumerically # by CONFIG_* macro name. +machine-$(CONFIG_ARCH_ALPINE) += alpine machine-$(CONFIG_ARCH_AT91) += at91 machine-$(CONFIG_ARCH_AXXIA) += axxia machine-$(CONFIG_ARCH_BCM) += bcm @@ -171,7 +171,6 @@ machine-$(CONFIG_ARCH_LPC32XX) += lpc32xx machine-$(CONFIG_ARCH_MESON) += meson machine-$(CONFIG_ARCH_MMP) += mmp machine-$(CONFIG_ARCH_MOXART) += moxart -machine-$(CONFIG_ARCH_MSM) += msm machine-$(CONFIG_ARCH_MV78XX0) += mv78xx0 machine-$(CONFIG_ARCH_MVEBU) += mvebu machine-$(CONFIG_ARCH_MXC) += imx diff --git a/arch/arm/boot/compressed/Makefile b/arch/arm/boot/compressed/Makefile index 3ea230aa94b7..6e1fb2b2ecc7 100644 --- a/arch/arm/boot/compressed/Makefile +++ b/arch/arm/boot/compressed/Makefile @@ -6,21 +6,6 @@ OBJS = -# Ensure that MMCIF loader code appears early in the image -# to minimise that number of bocks that have to be read in -# order to load it. -ifeq ($(CONFIG_ZBOOT_ROM_MMCIF),y) -OBJS += mmcif-sh7372.o -endif - -# Ensure that SDHI loader code appears early in the image -# to minimise that number of bocks that have to be read in -# order to load it. -ifeq ($(CONFIG_ZBOOT_ROM_SH_MOBILE_SDHI),y) -OBJS += sdhi-shmobile.o -OBJS += sdhi-sh7372.o -endif - AFLAGS_head.o += -DTEXT_OFFSET=$(TEXT_OFFSET) HEAD = head.o OBJS += misc.o decompress.o diff --git a/arch/arm/boot/compressed/head-shmobile.S b/arch/arm/boot/compressed/head-shmobile.S index e7f80928949c..22a75259faa3 100644 --- a/arch/arm/boot/compressed/head-shmobile.S +++ b/arch/arm/boot/compressed/head-shmobile.S @@ -25,36 +25,6 @@ /* load board-specific initialization code */ #include -#if defined(CONFIG_ZBOOT_ROM_MMCIF) || defined(CONFIG_ZBOOT_ROM_SH_MOBILE_SDHI) - /* Load image from MMC/SD */ - adr sp, __tmp_stack + 256 - ldr r0, __image_start - ldr r1, __image_end - subs r1, r1, r0 - ldr r0, __load_base - bl mmc_loader - - /* Jump to loaded code */ - ldr r0, __loaded - ldr r1, __image_start - sub r0, r0, r1 - ldr r1, __load_base - add pc, r0, r1 - -__image_start: - .long _start -__image_end: - .long _got_end -__load_base: - .long MEMORY_START + 0x02000000 @ Load at 32Mb into SDRAM -__loaded: - .long __continue - .align -__tmp_stack: - .space 256 -__continue: -#endif /* CONFIG_ZBOOT_ROM_MMC || CONFIG_ZBOOT_ROM_SH_MOBILE_SDHI */ - adr r0, dtb_info ldmia r0, {r1, r3, r4, r5, r7} diff --git a/arch/arm/boot/compressed/mmcif-sh7372.c b/arch/arm/boot/compressed/mmcif-sh7372.c deleted file mode 100644 index 672ae95db5c3..000000000000 --- a/arch/arm/boot/compressed/mmcif-sh7372.c +++ /dev/null @@ -1,88 +0,0 @@ -/* - * sh7372 MMCIF loader - * - * Copyright (C) 2010 Magnus Damm - * Copyright (C) 2010 Simon Horman - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - */ - -#include -#include -#include - -#define MMCIF_BASE (void __iomem *)0xe6bd0000 - -#define PORT84CR (void __iomem *)0xe6050054 -#define PORT85CR (void __iomem *)0xe6050055 -#define PORT86CR (void __iomem *)0xe6050056 -#define PORT87CR (void __iomem *)0xe6050057 -#define PORT88CR (void __iomem *)0xe6050058 -#define PORT89CR (void __iomem *)0xe6050059 -#define PORT90CR (void __iomem *)0xe605005a -#define PORT91CR (void __iomem *)0xe605005b -#define PORT92CR (void __iomem *)0xe605005c -#define PORT99CR (void __iomem *)0xe6050063 - -#define SMSTPCR3 (void __iomem *)0xe615013c - -/* SH7372 specific MMCIF loader - * - * loads the zImage from an MMC card starting from block 1. - * - * The image must be start with a vrl4 header and - * the zImage must start at offset 512 of the image. That is, - * at block 2 (=byte 1024) on the media - * - * Use the following line to write the vrl4 formated zImage - * to an MMC card - * # dd if=vrl4.out of=/dev/sdx bs=512 seek=1 - */ -asmlinkage void mmc_loader(unsigned char *buf, unsigned long len) -{ - mmc_init_progress(); - mmc_update_progress(MMC_PROGRESS_ENTER); - - /* Initialise MMC - * registers: PORT84CR-PORT92CR - * (MMCD0_0-MMCD0_7,MMCCMD0 Control) - * value: 0x04 - select function 4 - */ - __raw_writeb(0x04, PORT84CR); - __raw_writeb(0x04, PORT85CR); - __raw_writeb(0x04, PORT86CR); - __raw_writeb(0x04, PORT87CR); - __raw_writeb(0x04, PORT88CR); - __raw_writeb(0x04, PORT89CR); - __raw_writeb(0x04, PORT90CR); - __raw_writeb(0x04, PORT91CR); - __raw_writeb(0x04, PORT92CR); - - /* Initialise MMC - * registers: PORT99CR (MMCCLK0 Control) - * value: 0x10 | 0x04 - enable output | select function 4 - */ - __raw_writeb(0x14, PORT99CR); - - /* Enable clock to MMC hardware block */ - __raw_writel(__raw_readl(SMSTPCR3) & ~(1 << 12), SMSTPCR3); - - mmc_update_progress(MMC_PROGRESS_INIT); - - /* setup MMCIF hardware */ - sh_mmcif_boot_init(MMCIF_BASE); - - mmc_update_progress(MMC_PROGRESS_LOAD); - - /* load kernel via MMCIF interface */ - sh_mmcif_boot_do_read(MMCIF_BASE, 2, /* Kernel is at block 2 */ - (len + SH_MMCIF_BBS - 1) / SH_MMCIF_BBS, buf); - - - /* Disable clock to MMC hardware block */ - __raw_writel(__raw_readl(SMSTPCR3) | (1 << 12), SMSTPCR3); - - mmc_update_progress(MMC_PROGRESS_DONE); -} diff --git a/arch/arm/boot/compressed/sdhi-sh7372.c b/arch/arm/boot/compressed/sdhi-sh7372.c deleted file mode 100644 index d279294f2381..000000000000 --- a/arch/arm/boot/compressed/sdhi-sh7372.c +++ /dev/null @@ -1,95 +0,0 @@ -/* - * SuperH Mobile SDHI - * - * Copyright (C) 2010 Magnus Damm - * Copyright (C) 2010 Kuninori Morimoto - * Copyright (C) 2010 Simon Horman - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Parts inspired by u-boot - */ - -#include -#include -#include -#include - -#include "sdhi-shmobile.h" - -#define PORT179CR 0xe60520b3 -#define PORT180CR 0xe60520b4 -#define PORT181CR 0xe60520b5 -#define PORT182CR 0xe60520b6 -#define PORT183CR 0xe60520b7 -#define PORT184CR 0xe60520b8 - -#define SMSTPCR3 0xe615013c - -#define CR_INPUT_ENABLE 0x10 -#define CR_FUNCTION1 0x01 - -#define SDHI1_BASE (void __iomem *)0xe6860000 -#define SDHI_BASE SDHI1_BASE - -/* SuperH Mobile SDHI loader - * - * loads the zImage from an SD card starting from block 0 - * on physical partition 1 - * - * The image must be start with a vrl4 header and - * the zImage must start at offset 512 of the image. That is, - * at block 1 (=byte 512) of physical partition 1 - * - * Use the following line to write the vrl4 formated zImage - * to an SD card - * # dd if=vrl4.out of=/dev/sdx bs=512 - */ -asmlinkage void mmc_loader(unsigned short *buf, unsigned long len) -{ - int high_capacity; - - mmc_init_progress(); - - mmc_update_progress(MMC_PROGRESS_ENTER); - /* Initialise SDHI1 */ - /* PORT184CR: GPIO_FN_SDHICMD1 Control */ - __raw_writeb(CR_FUNCTION1, PORT184CR); - /* PORT179CR: GPIO_FN_SDHICLK1 Control */ - __raw_writeb(CR_INPUT_ENABLE|CR_FUNCTION1, PORT179CR); - /* PORT181CR: GPIO_FN_SDHID1_3 Control */ - __raw_writeb(CR_FUNCTION1, PORT183CR); - /* PORT182CR: GPIO_FN_SDHID1_2 Control */ - __raw_writeb(CR_FUNCTION1, PORT182CR); - /* PORT183CR: GPIO_FN_SDHID1_1 Control */ - __raw_writeb(CR_FUNCTION1, PORT181CR); - /* PORT180CR: GPIO_FN_SDHID1_0 Control */ - __raw_writeb(CR_FUNCTION1, PORT180CR); - - /* Enable clock to SDHI1 hardware block */ - __raw_writel(__raw_readl(SMSTPCR3) & ~(1 << 13), SMSTPCR3); - - /* setup SDHI hardware */ - mmc_update_progress(MMC_PROGRESS_INIT); - high_capacity = sdhi_boot_init(SDHI_BASE); - if (high_capacity < 0) - goto err; - - mmc_update_progress(MMC_PROGRESS_LOAD); - /* load kernel */ - if (sdhi_boot_do_read(SDHI_BASE, high_capacity, - 0, /* Kernel is at block 1 */ - (len + TMIO_BBS - 1) / TMIO_BBS, buf)) - goto err; - - /* Disable clock to SDHI1 hardware block */ - __raw_writel(__raw_readl(SMSTPCR3) | (1 << 13), SMSTPCR3); - - mmc_update_progress(MMC_PROGRESS_DONE); - - return; -err: - for(;;); -} diff --git a/arch/arm/boot/compressed/sdhi-shmobile.c b/arch/arm/boot/compressed/sdhi-shmobile.c deleted file mode 100644 index bd3d46980955..000000000000 --- a/arch/arm/boot/compressed/sdhi-shmobile.c +++ /dev/null @@ -1,449 +0,0 @@ -/* - * SuperH Mobile SDHI - * - * Copyright (C) 2010 Magnus Damm - * Copyright (C) 2010 Kuninori Morimoto - * Copyright (C) 2010 Simon Horman - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Parts inspired by u-boot - */ - -#include -#include -#include -#include -#include -#include -#include - -#define OCR_FASTBOOT (1<<29) -#define OCR_HCS (1<<30) -#define OCR_BUSY (1<<31) - -#define RESP_CMD12 0x00000030 - -static inline u16 sd_ctrl_read16(void __iomem *base, int addr) -{ - return __raw_readw(base + addr); -} - -static inline u32 sd_ctrl_read32(void __iomem *base, int addr) -{ - return __raw_readw(base + addr) | - __raw_readw(base + addr + 2) << 16; -} - -static inline void sd_ctrl_write16(void __iomem *base, int addr, u16 val) -{ - __raw_writew(val, base + addr); -} - -static inline void sd_ctrl_write32(void __iomem *base, int addr, u32 val) -{ - __raw_writew(val, base + addr); - __raw_writew(val >> 16, base + addr + 2); -} - -#define ALL_ERROR (TMIO_STAT_CMD_IDX_ERR | TMIO_STAT_CRCFAIL | \ - TMIO_STAT_STOPBIT_ERR | TMIO_STAT_DATATIMEOUT | \ - TMIO_STAT_RXOVERFLOW | TMIO_STAT_TXUNDERRUN | \ - TMIO_STAT_CMDTIMEOUT | TMIO_STAT_ILL_ACCESS | \ - TMIO_STAT_ILL_FUNC) - -static int sdhi_intr(void __iomem *base) -{ - unsigned long state = sd_ctrl_read32(base, CTL_STATUS); - - if (state & ALL_ERROR) { - sd_ctrl_write32(base, CTL_STATUS, ~ALL_ERROR); - sd_ctrl_write32(base, CTL_IRQ_MASK, - ALL_ERROR | - sd_ctrl_read32(base, CTL_IRQ_MASK)); - return -EINVAL; - } - if (state & TMIO_STAT_CMDRESPEND) { - sd_ctrl_write32(base, CTL_STATUS, ~TMIO_STAT_CMDRESPEND); - sd_ctrl_write32(base, CTL_IRQ_MASK, - TMIO_STAT_CMDRESPEND | - sd_ctrl_read32(base, CTL_IRQ_MASK)); - return 0; - } - if (state & TMIO_STAT_RXRDY) { - sd_ctrl_write32(base, CTL_STATUS, ~TMIO_STAT_RXRDY); - sd_ctrl_write32(base, CTL_IRQ_MASK, - TMIO_STAT_RXRDY | TMIO_STAT_TXUNDERRUN | - sd_ctrl_read32(base, CTL_IRQ_MASK)); - return 0; - } - if (state & TMIO_STAT_DATAEND) { - sd_ctrl_write32(base, CTL_STATUS, ~TMIO_STAT_DATAEND); - sd_ctrl_write32(base, CTL_IRQ_MASK, - TMIO_STAT_DATAEND | - sd_ctrl_read32(base, CTL_IRQ_MASK)); - return 0; - } - - return -EAGAIN; -} - -static int sdhi_boot_wait_resp_end(void __iomem *base) -{ - int err = -EAGAIN, timeout = 10000000; - - while (timeout--) { - err = sdhi_intr(base); - if (err != -EAGAIN) - break; - udelay(1); - } - - return err; -} - -/* SDHI_CLK_CTRL */ -#define CLK_MMC_ENABLE (1 << 8) -#define CLK_MMC_INIT (1 << 6) /* clk / 256 */ - -static void sdhi_boot_mmc_clk_stop(void __iomem *base) -{ - sd_ctrl_write16(base, CTL_CLK_AND_WAIT_CTL, 0x0000); - msleep(10); - sd_ctrl_write16(base, CTL_SD_CARD_CLK_CTL, ~CLK_MMC_ENABLE & - sd_ctrl_read16(base, CTL_SD_CARD_CLK_CTL)); - msleep(10); -} - -static void sdhi_boot_mmc_clk_start(void __iomem *base) -{ - sd_ctrl_write16(base, CTL_SD_CARD_CLK_CTL, CLK_MMC_ENABLE | - sd_ctrl_read16(base, CTL_SD_CARD_CLK_CTL)); - msleep(10); - sd_ctrl_write16(base, CTL_CLK_AND_WAIT_CTL, CLK_MMC_ENABLE); - msleep(10); -} - -static void sdhi_boot_reset(void __iomem *base) -{ - sd_ctrl_write16(base, CTL_RESET_SD, 0x0000); - msleep(10); - sd_ctrl_write16(base, CTL_RESET_SD, 0x0001); - msleep(10); -} - -/* Set MMC clock / power. - * Note: This controller uses a simple divider scheme therefore it cannot - * run a MMC card at full speed (20MHz). The max clock is 24MHz on SD, but as - * MMC wont run that fast, it has to be clocked at 12MHz which is the next - * slowest setting. - */ -static int sdhi_boot_mmc_set_ios(void __iomem *base, struct mmc_ios *ios) -{ - if (sd_ctrl_read32(base, CTL_STATUS) & TMIO_STAT_CMD_BUSY) - return -EBUSY; - - if (ios->clock) - sd_ctrl_write16(base, CTL_SD_CARD_CLK_CTL, - ios->clock | CLK_MMC_ENABLE); - - /* Power sequence - OFF -> ON -> UP */ - switch (ios->power_mode) { - case MMC_POWER_OFF: /* power down SD bus */ - sdhi_boot_mmc_clk_stop(base); - break; - case MMC_POWER_ON: /* power up SD bus */ - break; - case MMC_POWER_UP: /* start bus clock */ - sdhi_boot_mmc_clk_start(base); - break; - } - - switch (ios->bus_width) { - case MMC_BUS_WIDTH_1: - sd_ctrl_write16(base, CTL_SD_MEM_CARD_OPT, 0x80e0); - break; - case MMC_BUS_WIDTH_4: - sd_ctrl_write16(base, CTL_SD_MEM_CARD_OPT, 0x00e0); - break; - } - - /* Let things settle. delay taken from winCE driver */ - udelay(140); - - return 0; -} - -/* These are the bitmasks the tmio chip requires to implement the MMC response - * types. Note that R1 and R6 are the same in this scheme. */ -#define RESP_NONE 0x0300 -#define RESP_R1 0x0400 -#define RESP_R1B 0x0500 -#define RESP_R2 0x0600 -#define RESP_R3 0x0700 -#define DATA_PRESENT 0x0800 -#define TRANSFER_READ 0x1000 - -static int sdhi_boot_request(void __iomem *base, struct mmc_command *cmd) -{ - int err, c = cmd->opcode; - - switch (mmc_resp_type(cmd)) { - case MMC_RSP_NONE: c |= RESP_NONE; break; - case MMC_RSP_R1: c |= RESP_R1; break; - case MMC_RSP_R1B: c |= RESP_R1B; break; - case MMC_RSP_R2: c |= RESP_R2; break; - case MMC_RSP_R3: c |= RESP_R3; break; - default: - return -EINVAL; - } - - /* No interrupts so this may not be cleared */ - sd_ctrl_write32(base, CTL_STATUS, ~TMIO_STAT_CMDRESPEND); - - sd_ctrl_write32(base, CTL_IRQ_MASK, TMIO_STAT_CMDRESPEND | - sd_ctrl_read32(base, CTL_IRQ_MASK)); - sd_ctrl_write32(base, CTL_ARG_REG, cmd->arg); - sd_ctrl_write16(base, CTL_SD_CMD, c); - - - sd_ctrl_write32(base, CTL_IRQ_MASK, - ~(TMIO_STAT_CMDRESPEND | ALL_ERROR) & - sd_ctrl_read32(base, CTL_IRQ_MASK)); - - err = sdhi_boot_wait_resp_end(base); - if (err) - return err; - - cmd->resp[0] = sd_ctrl_read32(base, CTL_RESPONSE); - - return 0; -} - -static int sdhi_boot_do_read_single(void __iomem *base, int high_capacity, - unsigned long block, unsigned short *buf) -{ - int err, i; - - /* CMD17 - Read */ - { - struct mmc_command cmd; - - cmd.opcode = MMC_READ_SINGLE_BLOCK | \ - TRANSFER_READ | DATA_PRESENT; - if (high_capacity) - cmd.arg = block; - else - cmd.arg = block * TMIO_BBS; - cmd.flags = MMC_RSP_R1; - err = sdhi_boot_request(base, &cmd); - if (err) - return err; - } - - sd_ctrl_write32(base, CTL_IRQ_MASK, - ~(TMIO_STAT_DATAEND | TMIO_STAT_RXRDY | - TMIO_STAT_TXUNDERRUN) & - sd_ctrl_read32(base, CTL_IRQ_MASK)); - err = sdhi_boot_wait_resp_end(base); - if (err) - return err; - - sd_ctrl_write16(base, CTL_SD_XFER_LEN, TMIO_BBS); - for (i = 0; i < TMIO_BBS / sizeof(*buf); i++) - *buf++ = sd_ctrl_read16(base, RESP_CMD12); - - err = sdhi_boot_wait_resp_end(base); - if (err) - return err; - - return 0; -} - -int sdhi_boot_do_read(void __iomem *base, int high_capacity, - unsigned long offset, unsigned short count, - unsigned short *buf) -{ - unsigned long i; - int err = 0; - - for (i = 0; i < count; i++) { - err = sdhi_boot_do_read_single(base, high_capacity, offset + i, - buf + (i * TMIO_BBS / - sizeof(*buf))); - if (err) - return err; - } - - return 0; -} - -#define VOLTAGES (MMC_VDD_32_33 | MMC_VDD_33_34) - -int sdhi_boot_init(void __iomem *base) -{ - bool sd_v2 = false, sd_v1_0 = false; - unsigned short cid; - int err, high_capacity = 0; - - sdhi_boot_mmc_clk_stop(base); - sdhi_boot_reset(base); - - /* mmc0: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0 */ - { - struct mmc_ios ios; - ios.power_mode = MMC_POWER_ON; - ios.bus_width = MMC_BUS_WIDTH_1; - ios.clock = CLK_MMC_INIT; - err = sdhi_boot_mmc_set_ios(base, &ios); - if (err) - return err; - } - - /* CMD0 */ - { - struct mmc_command cmd; - msleep(1); - cmd.opcode = MMC_GO_IDLE_STATE; - cmd.arg = 0; - cmd.flags = MMC_RSP_NONE; - err = sdhi_boot_request(base, &cmd); - if (err) - return err; - msleep(2); - } - - /* CMD8 - Test for SD version 2 */ - { - struct mmc_command cmd; - cmd.opcode = SD_SEND_IF_COND; - cmd.arg = (VOLTAGES != 0) << 8 | 0xaa; - cmd.flags = MMC_RSP_R1; - err = sdhi_boot_request(base, &cmd); /* Ignore error */ - if ((cmd.resp[0] & 0xff) == 0xaa) - sd_v2 = true; - } - - /* CMD55 - Get OCR (SD) */ - { - int timeout = 1000; - struct mmc_command cmd; - - cmd.arg = 0; - - do { - cmd.opcode = MMC_APP_CMD; - cmd.flags = MMC_RSP_R1; - cmd.arg = 0; - err = sdhi_boot_request(base, &cmd); - if (err) - break; - - cmd.opcode = SD_APP_OP_COND; - cmd.flags = MMC_RSP_R3; - cmd.arg = (VOLTAGES & 0xff8000); - if (sd_v2) - cmd.arg |= OCR_HCS; - cmd.arg |= OCR_FASTBOOT; - err = sdhi_boot_request(base, &cmd); - if (err) - break; - - msleep(1); - } while((!(cmd.resp[0] & OCR_BUSY)) && --timeout); - - if (!err && timeout) { - if (!sd_v2) - sd_v1_0 = true; - high_capacity = (cmd.resp[0] & OCR_HCS) == OCR_HCS; - } - } - - /* CMD1 - Get OCR (MMC) */ - if (!sd_v2 && !sd_v1_0) { - int timeout = 1000; - struct mmc_command cmd; - - do { - cmd.opcode = MMC_SEND_OP_COND; - cmd.arg = VOLTAGES | OCR_HCS; - cmd.flags = MMC_RSP_R3; - err = sdhi_boot_request(base, &cmd); - if (err) - return err; - - msleep(1); - } while((!(cmd.resp[0] & OCR_BUSY)) && --timeout); - - if (!timeout) - return -EAGAIN; - - high_capacity = (cmd.resp[0] & OCR_HCS) == OCR_HCS; - } - - /* CMD2 - Get CID */ - { - struct mmc_command cmd; - cmd.opcode = MMC_ALL_SEND_CID; - cmd.arg = 0; - cmd.flags = MMC_RSP_R2; - err = sdhi_boot_request(base, &cmd); - if (err) - return err; - } - - /* CMD3 - * MMC: Set the relative address - * SD: Get the relative address - * Also puts the card into the standby state - */ - { - struct mmc_command cmd; - cmd.opcode = MMC_SET_RELATIVE_ADDR; - cmd.arg = 0; - cmd.flags = MMC_RSP_R1; - err = sdhi_boot_request(base, &cmd); - if (err) - return err; - cid = cmd.resp[0] >> 16; - } - - /* CMD9 - Get CSD */ - { - struct mmc_command cmd; - cmd.opcode = MMC_SEND_CSD; - cmd.arg = cid << 16; - cmd.flags = MMC_RSP_R2; - err = sdhi_boot_request(base, &cmd); - if (err) - return err; - } - - /* CMD7 - Select the card */ - { - struct mmc_command cmd; - cmd.opcode = MMC_SELECT_CARD; - //cmd.arg = rca << 16; - cmd.arg = cid << 16; - //cmd.flags = MMC_RSP_R1B; - cmd.flags = MMC_RSP_R1; - err = sdhi_boot_request(base, &cmd); - if (err) - return err; - } - - /* CMD16 - Set the block size */ - { - struct mmc_command cmd; - cmd.opcode = MMC_SET_BLOCKLEN; - cmd.arg = TMIO_BBS; - cmd.flags = MMC_RSP_R1; - err = sdhi_boot_request(base, &cmd); - if (err) - return err; - } - - return high_capacity; -} diff --git a/arch/arm/boot/compressed/sdhi-shmobile.h b/arch/arm/boot/compressed/sdhi-shmobile.h deleted file mode 100644 index 92eaa09f985e..000000000000 --- a/arch/arm/boot/compressed/sdhi-shmobile.h +++ /dev/null @@ -1,11 +0,0 @@ -#ifndef SDHI_MOBILE_H -#define SDHI_MOBILE_H - -#include - -int sdhi_boot_do_read(void __iomem *base, int high_capacity, - unsigned long offset, unsigned short count, - unsigned short *buf); -int sdhi_boot_init(void __iomem *base); - -#endif diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index a1c776b8dcec..86217db2937a 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1,5 +1,7 @@ ifeq ($(CONFIG_OF),y) +dtb-$(CONFIG_ARCH_ALPINE) += \ + alpine-db.dtb dtb-$(CONFIG_MACH_ASM9260) += \ alphascale-asm9260-devkit.dtb # Keep at91 dtb files sorted alphabetically for each SoC @@ -42,6 +44,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \ sama5d34ek.dtb \ sama5d35ek.dtb \ sama5d36ek.dtb \ + at91-sama5d4_xplained.dtb \ at91-sama5d4ek.dtb dtb-$(CONFIG_ARCH_ATLAS6) += \ atlas6-evb.dtb @@ -59,13 +62,15 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ bcm4708-netgear-r6300-v2.dtb \ bcm47081-asus-rt-n18u.dtb \ bcm47081-buffalo-wzr-600dhp2.dtb \ - bcm47081-buffalo-wzr-900dhp.dtb + bcm47081-buffalo-wzr-900dhp.dtb \ + bcm4709-netgear-r8000.dtb dtb-$(CONFIG_ARCH_BCM_63XX) += \ bcm963138dvt.dtb dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \ bcm911360_entphn.dtb \ bcm911360k.dtb \ - bcm958300k.dtb + bcm958300k.dtb \ + bcm958305k.dtb dtb-$(CONFIG_ARCH_BCM_MOBILE) += \ bcm28155-ap.dtb \ bcm21664-garnet.dtb @@ -165,6 +170,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ kirkwood-lsxhl.dtb \ kirkwood-mplcec4.dtb \ kirkwood-mv88f6281gtw-ge.dtb \ + kirkwood-nas2big.dtb \ kirkwood-net2big.dtb \ kirkwood-net5big.dtb \ kirkwood-netgear_readynas_duo_v2.dtb \ @@ -199,6 +205,8 @@ dtb-$(CONFIG_ARCH_LPC32XX) += \ ea3250.dtb phy3250.dtb dtb-$(CONFIG_MACH_MESON6) += \ meson6-atv1200.dtb +dtb-$(CONFIG_MACH_MESON8) += \ + meson8-minix-neo-x8.dtb dtb-$(CONFIG_ARCH_MMP) += \ pxa168-aspenite.dtb \ pxa910-dkb.dtb \ @@ -299,9 +307,11 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-wandboard.dtb \ imx6q-wandboard-revb1.dtb dtb-$(CONFIG_SOC_IMX6SL) += \ - imx6sl-evk.dtb + imx6sl-evk.dtb \ + imx6sl-warp.dtb dtb-$(CONFIG_SOC_IMX6SX) += \ imx6sx-sabreauto.dtb \ + imx6sx-sdb-reva.dtb \ imx6sx-sdb.dtb dtb-$(CONFIG_SOC_LS1021A) += \ ls1021a-qds.dtb \ @@ -386,6 +396,8 @@ dtb-$(CONFIG_ARCH_OMAP3) += \ omap3-overo-storm-tobi.dtb \ omap3-overo-summit.dtb \ omap3-overo-tobi.dtb \ + omap3-pandora-600mhz.dtb \ + omap3-pandora-1ghz.dtb \ omap3-sbc-t3517.dtb \ omap3-sbc-t3530.dtb \ omap3-sbc-t3730.dtb \ @@ -401,7 +413,8 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-evmsk.dtb \ am335x-nano.dtb \ am335x-pepper.dtb \ - am335x-lxm.dtb + am335x-lxm.dtb \ + am335x-chiliboard.dtb dtb-$(CONFIG_ARCH_OMAP4) += \ omap4-duovero-parlor.dtb \ omap4-panda.dtb \ @@ -464,25 +477,23 @@ dtb-$(CONFIG_ARCH_S5PV210) += \ s5pv210-smdkv210.dtb \ s5pv210-torbreck.dtb dtb-$(CONFIG_ARCH_SHMOBILE_LEGACY) += \ - r8a73a4-ape6evm.dtb \ - r8a73a4-ape6evm-reference.dtb \ r8a7740-armadillo800eva.dtb \ r8a7778-bockw.dtb \ r8a7778-bockw-reference.dtb \ r8a7779-marzen.dtb \ - sh7372-mackerel.dtb \ - sh73a0-kzm9g.dtb \ - sh73a0-kzm9g-reference.dtb + sh73a0-kzm9g.dtb dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \ emev2-kzm9d.dtb \ r7s72100-genmai.dtb \ r8a73a4-ape6evm.dtb \ r8a7740-armadillo800eva.dtb \ + r8a7778-bockw.dtb \ r8a7779-marzen.dtb \ r8a7790-lager.dtb \ r8a7791-henninger.dtb \ r8a7791-koelsch.dtb \ - r8a7794-alt.dtb + r8a7794-alt.dtb \ + sh73a0-kzm9g.dtb dtb-$(CONFIG_ARCH_SOCFPGA) += \ socfpga_arria5_socdk.dtb \ socfpga_arria10_socdk.dtb \ @@ -577,6 +588,7 @@ dtb-$(CONFIG_ARCH_TEGRA_114_SOC) += \ dtb-$(CONFIG_ARCH_TEGRA_124_SOC) += \ tegra124-jetson-tk1.dtb \ tegra124-nyan-big.dtb \ + tegra124-nyan-blaze.dtb \ tegra124-venice2.dtb dtb-$(CONFIG_ARCH_U300) += \ ste-u300.dtb @@ -624,11 +636,14 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \ armada-388-db.dtb \ armada-388-gp.dtb \ armada-388-rd.dtb +dtb-$(CONFIG_MACH_ARMADA_39X) += \ + armada-398-db.dtb dtb-$(CONFIG_MACH_ARMADA_XP) += \ armada-xp-axpwifiap.dtb \ armada-xp-db.dtb \ armada-xp-gp.dtb \ armada-xp-lenovo-ix4-300d.dtb \ + armada-xp-linksys-mamba.dtb \ armada-xp-matrix.dtb \ armada-xp-netgear-rn2120.dtb \ armada-xp-openblocks-ax3-4.dtb \ diff --git a/arch/arm/boot/dts/alpine-db.dts b/arch/arm/boot/dts/alpine-db.dts new file mode 100644 index 000000000000..dfb5a0802273 --- /dev/null +++ b/arch/arm/boot/dts/alpine-db.dts @@ -0,0 +1,35 @@ +/* + * Copyright 2015 Annapurna Labs Ltd. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * Alternatively, redistribution and use in source and binary forms, with or + * without modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + */ + +/dts-v1/; + +#include "alpine.dtsi" + +/ { + model = "Annapurna Labs Alpine Dev Board"; + /* no need for anything outside SOC */ +}; + diff --git a/arch/arm/boot/dts/alpine.dtsi b/arch/arm/boot/dts/alpine.dtsi new file mode 100644 index 000000000000..9af2d60e9a7f --- /dev/null +++ b/arch/arm/boot/dts/alpine.dtsi @@ -0,0 +1,160 @@ +/* + * Copyright 2015 Annapurna Labs Ltd. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * Alternatively, redistribution and use in source and binary forms, with or + * without modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + */ + +#include +#include "skeleton64.dtsi" + +/ { + /* SOC compatibility */ + compatible = "al,alpine"; + + /* CPU Configuration */ + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "al,alpine-smp"; + + cpu@0 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <0>; + clock-frequency = <0>; /* Filled by loader */ + }; + + cpu@1 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <1>; + clock-frequency = <0>; /* Filled by loader */ + }; + + cpu@2 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <2>; + clock-frequency = <0>; /* Filled by loader */ + }; + + cpu@3 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <3>; + clock-frequency = <0>; /* Filled by loader */ + }; + }; + + soc { + #address-cells = <2>; + #size-cells = <2>; + compatible = "simple-bus"; + interrupt-parent = <&gic>; + ranges; + + arch-timer { + compatible = "arm,cortex-a15-timer", + "arm,armv7-timer"; + interrupts = + , + , + , + ; + clock-frequency = <0>; /* Filled by loader */ + }; + + /* Interrupt Controller */ + gic: gic@fb001000 { + compatible = "arm,cortex-a15-gic"; + #interrupt-cells = <3>; + #size-cells = <0>; + #address-cells = <0>; + interrupt-controller; + reg = <0x0 0xfb001000 0x0 0x1000>, + <0x0 0xfb002000 0x0 0x2000>, + <0x0 0xfb004000 0x0 0x1000>, + <0x0 0xfb006000 0x0 0x2000>; + interrupts = + ; + }; + + /* CPU Resume registers */ + cpu-resume@fbff5ec0 { + compatible = "al,alpine-cpu-resume"; + reg = <0x0 0xfbff5ec0 0x0 0x30>; + }; + + /* North Bridge Service Registers */ + sysfabric-service@fb070000 { + compatible = "al,alpine-sysfabric-service", "syscon"; + reg = <0x0 0xfb070000 0x0 0x10000>; + }; + + /* Performance Monitor Unit */ + pmu { + compatible = "arm,cortex-a15-pmu"; + interrupts = , + , + , + ; + }; + + uart0:uart@fd883000 { + compatible = "ns16550a"; + reg = <0x0 0xfd883000 0x0 0x1000>; + clock-frequency = <0>; /* Filled by loader */ + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + }; + + uart1:uart@0xfd884000 { + compatible = "ns16550a"; + reg = <0x0 0xfd884000 0x0 0x1000>; + clock-frequency = <0>; /* Filled by loader */ + interrupts = ; + reg-shift = <2>; + reg-io-width = <4>; + }; + + /* Internal PCIe Controller */ + pcie-internal@0xfbc00000 { + compatible = "pci-host-ecam-generic"; + device_type = "pci"; + #size-cells = <2>; + #address-cells = <3>; + #interrupt-cells = <1>; + reg = <0x0 0xfbc00000 0x0 0x100000>; + interrupt-map-mask = <0xf800 0 0 7>; + /* Add legacy interrupts for SATA devices only */ + interrupt-map = <0x4000 0 0 1 &gic 0 43 4>, + <0x4800 0 0 1 &gic 0 44 4>; + + /* 32 bit non prefetchable memory space */ + ranges = <0x02000000 0x0 0xfe000000 0x0 0xfe000000 0x0 0x1000000>; + + bus-range = <0x00 0x00>; + }; + }; +}; diff --git a/arch/arm/boot/dts/am335x-chiliboard.dts b/arch/arm/boot/dts/am335x-chiliboard.dts new file mode 100644 index 000000000000..310da20a8aa7 --- /dev/null +++ b/arch/arm/boot/dts/am335x-chiliboard.dts @@ -0,0 +1,112 @@ +/* + * Copyright (C) 2015 Jablotron s.r.o. -- http://www.jablotron.com/ + * Author: Rostislav Lisovy + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; +#include "am335x-chilisom.dtsi" + +/ { + model = "AM335x Chiliboard"; + compatible = "grinn,am335x-chiliboard", "grinn,am335x-chilisom", + "ti,am33xx"; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_gpio_pins>; + + led0 { + label = "led0"; + gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; + default-state = "keep"; + linux,default-trigger = "heartbeat"; + }; + + led1 { + label = "led1"; + gpios = <&gpio3 8 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + }; +}; + +&am33xx_pinmux { + usb1_drvvbus: usb1_drvvbus { + pinctrl-single,pins = < + 0x234 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* usb1_drvvbus.usb1_drvvbus */ + >; + }; + + sd_pins: pinmux_sd_card { + pinctrl-single,pins = < + 0xf0 (PIN_INPUT | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + 0xf4 (PIN_INPUT | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + 0xf8 (PIN_INPUT | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + 0xfc (PIN_INPUT | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + 0x100 (PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + 0x104 (PIN_INPUT | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + >; + }; + + led_gpio_pins: led_gpio_pins { + pinctrl-single,pins = < + 0x1e4 (PIN_OUTPUT | MUX_MODE7) /* emu0.gpio3_7 */ + 0x1e8 (PIN_OUTPUT | MUX_MODE7) /* emu1.gpio3_8 */ + >; + }; +}; + +&ldo4_reg { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; +}; + +/* Ethernet */ +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rmii"; +}; + +&phy_sel { + rmii-clock-ext; +}; + +/* USB */ +&usb { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb1 { + pinctrl-names = "default"; + pinctrl-0 = <&usb1_drvvbus>; + + status = "okay"; + dr_mode = "host"; +}; + +&cppi41dma { + status = "okay"; +}; + +/* microSD */ +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&sd_pins>; + vmmc-supply = <&ldo4_reg>; + bus-width = <0x4>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/am335x-chilisom.dtsi b/arch/arm/boot/dts/am335x-chilisom.dtsi new file mode 100644 index 000000000000..7e9a34dffe21 --- /dev/null +++ b/arch/arm/boot/dts/am335x-chilisom.dtsi @@ -0,0 +1,239 @@ +/* + * Copyright (C) 2015 Jablotron s.r.o. -- http://www.jablotron.com/ + * Author: Rostislav Lisovy + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include "am33xx.dtsi" + +/ { + model = "Grinn AM335x ChiliSOM"; + compatible = "grinn,am335x-chilisom", "ti,am33xx"; + + cpus { + cpu@0 { + cpu0-supply = <&dcdc2_reg>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x20000000>; /* 512 MB */ + }; +}; + +&am33xx_pinmux { + pinctrl-names = "default"; + + i2c0_pins: pinmux_i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + cpsw_default: cpsw_default { + pinctrl-single,pins = < + /* Slave 1 */ + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs */ + 0x110 (PIN_INPUT_PULLUP | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ + 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txen.rmii1_txen */ + 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ + 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ + 0x13c (PIN_INPUT_PULLUP | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ + 0x140 (PIN_INPUT_PULLUP | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_ref_clk.rmii_ref_clk */ + >; + }; + + cpsw_sleep: cpsw_sleep { + pinctrl-single,pins = < + /* Slave 1 reset value */ + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + davinci_mdio_default: davinci_mdio_default { + pinctrl-single,pins = < + /* mdio_data.mdio_data */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) + /* mdio_clk.mdio_clk */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) + >; + }; + + davinci_mdio_sleep: davinci_mdio_sleep { + pinctrl-single,pins = < + /* MDIO reset value */ + 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + + nandflash_pins: nandflash_pins { + pinctrl-single,pins = < + 0x00 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x04 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x08 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0x0c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x7c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x90 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + >; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + + status = "okay"; + clock-frequency = <400000>; + + tps: tps@24 { + reg = <0x24>; + }; + +}; + +/include/ "tps65217.dtsi" + +&tps { + regulators { + dcdc1_reg: regulator@0 { + regulator-name = "vdds_dpr"; + regulator-always-on; + }; + + dcdc2_reg: regulator@1 { + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1325000>; + regulator-boot-on; + regulator-always-on; + }; + + dcdc3_reg: regulator@2 { + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: regulator@3 { + regulator-name = "vio,vrtc,vdds"; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: regulator@4 { + regulator-name = "vdd_3v3aux"; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: regulator@5 { + regulator-name = "vdd_1v8"; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: regulator@6 { + regulator-name = "vdd_3v3d"; + regulator-boot-on; + regulator-always-on; + }; + }; +}; + +/* Ethernet MAC */ +&mac { + slaves = <1>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cpsw_default>; + pinctrl-1 = <&cpsw_sleep>; + status = "okay"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; +}; + +/* NAND Flash */ +&elm { + status = "okay"; +}; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nandflash_pins>; + ranges = <0 0 0x08000000 0x01000000>; /* CS0 0 @addr 0x08000000, size 0x01000000 */ + nand@0,0 { + reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ + ti,nand-ecc-opt = "bch8"; + ti,elm-id = <&elm>; + nand-bus-width = <8>; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <40>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + }; +}; diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts index df5fee6b6b4b..87fc7a35e802 100644 --- a/arch/arm/boot/dts/am335x-evmsk.dts +++ b/arch/arm/boot/dts/am335x-evmsk.dts @@ -15,6 +15,7 @@ #include "am33xx.dtsi" #include +#include / { model = "TI AM335x EVM-SK"; @@ -647,6 +648,16 @@ cap-power-off-card; pinctrl-names = "default"; pinctrl-0 = <&mmc2_pins>; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1271"; + reg = <2>; + interrupt-parent = <&gpio1>; + interrupts = <31 IRQ_TYPE_LEVEL_HIGH>; /* gpio 31 */ + ref-clock-frequency = <38400000>; + }; }; &mcasp1 { diff --git a/arch/arm/boot/dts/am335x-nano.dts b/arch/arm/boot/dts/am335x-nano.dts index a3466455b171..5ed4ca6eaf55 100644 --- a/arch/arm/boot/dts/am335x-nano.dts +++ b/arch/arm/boot/dts/am335x-nano.dts @@ -213,7 +213,9 @@ pinctrl-0 = <&i2c0_pins>; gpio@20 { - compatible = "mcp,mcp23017"; + compatible = "microchip,mcp23017"; + gpio-controller; + #gpio-cells = <2>; reg = <0x20>; }; @@ -222,7 +224,7 @@ }; eeprom@53 { - compatible = "mcp,24c02"; + compatible = "microchip,24c02"; reg = <0x53>; pagesize = <8>; }; @@ -297,8 +299,8 @@ | |-->0x004FFFFF-> Kernel end | |-->0x00500000-> File system start | | - | |-->0x014FFFFF-> File system end - | |-->0x01500000-> User data start + | |-->0x01FFFFFF-> File system end + | |-->0x02000000-> User data start | | | |-->0x03FFFFFF-> User data end | |-->0x04000000-> Data storage start @@ -327,12 +329,12 @@ partition@4 { label = "rootfs"; - reg = <0x00500000 0x01000000>; /* 16MB */ + reg = <0x00500000 0x01b00000>; /* 27MB */ }; partition@5 { label = "user"; - reg = <0x01500000 0x02b00000>; /* 43MB */ + reg = <0x02000000 0x02000000>; /* 32MB */ }; partition@6 { @@ -343,7 +345,7 @@ }; &mac { - dual_emac = <1>; + dual_emac; status = "okay"; }; @@ -353,11 +355,13 @@ &cpsw_emac0 { phy_id = <&davinci_mdio>, <0>; + phy-mode = "mii"; dual_emac_res_vlan = <1>; }; &cpsw_emac1 { phy_id = <&davinci_mdio>, <1>; + phy-mode = "mii"; dual_emac_res_vlan = <2>; }; diff --git a/arch/arm/boot/dts/am33xx-clocks.dtsi b/arch/arm/boot/dts/am33xx-clocks.dtsi index 071b56aa0c7e..afb4b3a7bab4 100644 --- a/arch/arm/boot/dts/am33xx-clocks.dtsi +++ b/arch/arm/boot/dts/am33xx-clocks.dtsi @@ -7,7 +7,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -&scrm_clocks { +&scm_clocks { sys_clkin_ck: sys_clkin_ck { #clock-cells = <0>; compatible = "ti,mux-clock"; diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index acd37057bca9..21fcc440fc1a 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -83,20 +83,6 @@ }; }; - am33xx_control_module: control_module@4a002000 { - compatible = "syscon"; - reg = <0x44e10000 0x7fc>; - }; - - am33xx_pinmux: pinmux@44e10800 { - compatible = "pinctrl-single"; - reg = <0x44e10800 0x0238>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-single,register-width = <32>; - pinctrl-single,function-mask = <0x7f>; - }; - /* * XXX: Use a flat representation of the AM33XX interconnect. * The real AM33XX interconnect network is quite complex. Since @@ -111,35 +97,56 @@ ranges; ti,hwmods = "l3_main"; - prcm: prcm@44e00000 { - compatible = "ti,am3-prcm"; - reg = <0x44e00000 0x4000>; + l4_wkup: l4_wkup@44c00000 { + compatible = "ti,am3-l4-wkup", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x44c00000 0x280000>; - prcm_clocks: clocks { + prcm: prcm@200000 { + compatible = "ti,am3-prcm"; + reg = <0x200000 0x4000>; + + prcm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + prcm_clockdomains: clockdomains { + }; + }; + + scm: scm@210000 { + compatible = "ti,am3-scm", "simple-bus"; + reg = <0x210000 0x2000>; #address-cells = <1>; - #size-cells = <0>; + #size-cells = <1>; + ranges = <0 0x210000 0x2000>; + + am33xx_pinmux: pinmux@800 { + compatible = "pinctrl-single"; + reg = <0x800 0x238>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x7f>; + }; + + scm_conf: scm_conf@0 { + compatible = "syscon"; + reg = <0x0 0x800>; + #address-cells = <1>; + #size-cells = <1>; + + scm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + scm_clockdomains: clockdomains { + }; }; - - prcm_clockdomains: clockdomains { - }; - }; - - scrm: scrm@44e10000 { - compatible = "ti,am3-scrm"; - reg = <0x44e10000 0x2000>; - - scrm_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - scrm_clockdomains: clockdomains { - }; - }; - - cm: syscon@44e10000 { - compatible = "ti,am33xx-controlmodule", "syscon"; - reg = <0x44e10000 0x800>; }; intc: interrupt-controller@48200000 { @@ -350,7 +357,7 @@ reg = <0x481cc000 0x2000>; clocks = <&dcan0_fck>; clock-names = "fck"; - syscon-raminit = <&am33xx_control_module 0x644 0>; + syscon-raminit = <&scm_conf 0x644 0>; interrupts = <52>; status = "disabled"; }; @@ -361,7 +368,7 @@ reg = <0x481d0000 0x2000>; clocks = <&dcan1_fck>; clock-names = "fck"; - syscon-raminit = <&am33xx_control_module 0x644 1>; + syscon-raminit = <&scm_conf 0x644 1>; interrupts = <55>; status = "disabled"; }; @@ -720,7 +727,7 @@ */ interrupts = <40 41 42 43>; ranges; - syscon = <&cm>; + syscon = <&scm_conf>; status = "disabled"; davinci_mdio: mdio@4a101000 { diff --git a/arch/arm/boot/dts/am3517.dtsi b/arch/arm/boot/dts/am3517.dtsi index c90724bded10..f164dce08755 100644 --- a/arch/arm/boot/dts/am3517.dtsi +++ b/arch/arm/boot/dts/am3517.dtsi @@ -31,7 +31,7 @@ status = "disabled"; reg = <0x5c000000 0x30000>; interrupts = <67 68 69 70>; - syscon = <&omap3_scm_general>; + syscon = <&scm_conf>; ti,davinci-ctrl-reg-offset = <0x10000>; ti,davinci-ctrl-mod-reg-offset = <0>; ti,davinci-ctrl-ram-offset = <0x20000>; diff --git a/arch/arm/boot/dts/am35xx-clocks.dtsi b/arch/arm/boot/dts/am35xx-clocks.dtsi index df489d310b50..518b8fde88b0 100644 --- a/arch/arm/boot/dts/am35xx-clocks.dtsi +++ b/arch/arm/boot/dts/am35xx-clocks.dtsi @@ -7,7 +7,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -&scrm_clocks { +&scm_clocks { emac_ick: emac_ick { #clock-cells = <0>; compatible = "ti,am35xx-gate-clock"; diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index 8a099bc10c1e..c80a3e233792 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -66,22 +66,6 @@ cache-level = <2>; }; - am43xx_control_module: control_module@4a002000 { - compatible = "syscon"; - reg = <0x44e10000 0x7f4>; - }; - - am43xx_pinmux: pinmux@44e10800 { - compatible = "ti,am437-padconf", "pinctrl-single"; - reg = <0x44e10800 0x31c>; - #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - pinctrl-single,register-width = <32>; - pinctrl-single,function-mask = <0xffffffff>; - }; - ocp { compatible = "ti,am4372-l3-noc", "simple-bus"; #address-cells = <1>; @@ -93,29 +77,58 @@ interrupts = , ; - prcm: prcm@44df0000 { - compatible = "ti,am4-prcm"; - reg = <0x44df0000 0x11000>; + l4_wkup: l4_wkup@44c00000 { + compatible = "ti,am4-l4-wkup", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x44c00000 0x287000>; - prcm_clocks: clocks { + prcm: prcm@1f0000 { + compatible = "ti,am4-prcm"; + reg = <0x1f0000 0x11000>; + + prcm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + prcm_clockdomains: clockdomains { + }; + }; + + scm: scm@210000 { + compatible = "ti,am4-scm", "simple-bus"; + reg = <0x210000 0x4000>; #address-cells = <1>; - #size-cells = <0>; - }; + #size-cells = <1>; + ranges = <0 0x210000 0x4000>; - prcm_clockdomains: clockdomains { - }; - }; + am43xx_pinmux: pinmux@800 { + compatible = "ti,am437-padconf", + "pinctrl-single"; + reg = <0x800 0x31c>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0xffffffff>; + }; - scrm: scrm@44e10000 { - compatible = "ti,am4-scrm"; - reg = <0x44e10000 0x2000>; + scm_conf: scm_conf@0 { + compatible = "syscon"; + reg = <0x0 0x800>; + #address-cells = <1>; + #size-cells = <1>; - scrm_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; + scm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + }; - scrm_clockdomains: clockdomains { + scm_clockdomains: clockdomains { + }; }; }; @@ -796,7 +809,7 @@ }; ocp2scp0: ocp2scp@483a8000 { - compatible = "ti,omap-ocp2scp"; + compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp"; #address-cells = <1>; #size-cells = <1>; ranges; @@ -815,7 +828,7 @@ }; ocp2scp1: ocp2scp@483e8000 { - compatible = "ti,omap-ocp2scp"; + compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp"; #address-cells = <1>; #size-cells = <1>; ranges; @@ -893,7 +906,7 @@ }; hdq: hdq@48347000 { - compatible = "ti,am43xx-hdq"; + compatible = "ti,am4372-hdq"; reg = <0x48347000 0x1000>; interrupts = ; clocks = <&func_12m_clk>; @@ -942,7 +955,7 @@ clocks = <&dcan0_fck>; clock-names = "fck"; reg = <0x481cc000 0x2000>; - syscon-raminit = <&am43xx_control_module 0x644 0>; + syscon-raminit = <&scm_conf 0x644 0>; interrupts = ; status = "disabled"; }; @@ -953,7 +966,7 @@ clocks = <&dcan1_fck>; clock-names = "fck"; reg = <0x481d0000 0x2000>; - syscon-raminit = <&am43xx_control_module 0x644 1>; + syscon-raminit = <&scm_conf 0x644 1>; interrupts = ; status = "disabled"; }; diff --git a/arch/arm/boot/dts/am437x-idk-evm.dts b/arch/arm/boot/dts/am437x-idk-evm.dts index 0198f5a62b96..378344271746 100644 --- a/arch/arm/boot/dts/am437x-idk-evm.dts +++ b/arch/arm/boot/dts/am437x-idk-evm.dts @@ -133,6 +133,20 @@ >; }; + i2c2_pins_default: i2c2_pins_default { + pinctrl-single,pins = < + 0x1e8 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE3) /* cam1_data1.i2c2_scl */ + 0x1ec (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE3) /* cam1_data0.i2c2_sda */ + >; + }; + + i2c2_pins_sleep: i2c2_pins_sleep { + pinctrl-single,pins = < + 0x1e8 (PIN_INPUT_PULLDOWN | MUX_MODE7) + 0x1ec (PIN_INPUT_PULLDOWN | MUX_MODE7) + >; + }; + mmc1_pins_default: pinmux_mmc1_pins_default { pinctrl-single,pins = < 0x100 (PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */ @@ -263,6 +277,14 @@ }; }; +&i2c2 { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c2_pins_default>; + pinctrl-1 = <&i2c2_pins_sleep>; + clock-frequency = <100000>; +}; + &epwmss0 { status = "okay"; }; diff --git a/arch/arm/boot/dts/am437x-sk-evm.dts b/arch/arm/boot/dts/am437x-sk-evm.dts index 8ae29c955c11..c17097d2c167 100644 --- a/arch/arm/boot/dts/am437x-sk-evm.dts +++ b/arch/arm/boot/dts/am437x-sk-evm.dts @@ -49,7 +49,7 @@ pinctrl-0 = <&matrix_keypad_pins>; debounce-delay-ms = <5>; - col-scan-delay-us = <1500>; + col-scan-delay-us = <5>; row-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH /* Bank5, pin5 */ &gpio5 6 GPIO_ACTIVE_HIGH>; /* Bank5, pin6 */ @@ -473,7 +473,7 @@ interrupt-parent = <&gpio0>; interrupts = <31 0>; - wake-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>; touchscreen-size-x = <480>; touchscreen-size-y = <272>; diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts index 1d7109196872..795d68af6df9 100644 --- a/arch/arm/boot/dts/am43x-epos-evm.dts +++ b/arch/arm/boot/dts/am43x-epos-evm.dts @@ -69,7 +69,48 @@ }; }; - am43xx_pinmux: pinmux@44e10800 { + matrix_keypad: matrix_keypad@0 { + compatible = "gpio-matrix-keypad"; + debounce-delay-ms = <5>; + col-scan-delay-us = <2>; + + row-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH /* Bank0, pin12 */ + &gpio0 13 GPIO_ACTIVE_HIGH /* Bank0, pin13 */ + &gpio0 14 GPIO_ACTIVE_HIGH /* Bank0, pin14 */ + &gpio0 15 GPIO_ACTIVE_HIGH>; /* Bank0, pin15 */ + + col-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH /* Bank3, pin9 */ + &gpio3 10 GPIO_ACTIVE_HIGH /* Bank3, pin10 */ + &gpio2 18 GPIO_ACTIVE_HIGH /* Bank2, pin18 */ + &gpio2 19 GPIO_ACTIVE_HIGH>; /* Bank2, pin19 */ + + linux,keymap = <0x00000201 /* P1 */ + 0x01000204 /* P4 */ + 0x02000207 /* P7 */ + 0x0300020a /* NUMERIC_STAR */ + 0x00010202 /* P2 */ + 0x01010205 /* P5 */ + 0x02010208 /* P8 */ + 0x03010200 /* P0 */ + 0x00020203 /* P3 */ + 0x01020206 /* P6 */ + 0x02020209 /* P9 */ + 0x0302020b /* NUMERIC_POUND */ + 0x00030067 /* UP */ + 0x0103006a /* RIGHT */ + 0x0203006c /* DOWN */ + 0x03030069>; /* LEFT */ + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <0 51 53 56 62 75 101 152 255>; + default-brightness-level = <8>; + }; +}; + +&am43xx_pinmux { cpsw_default: cpsw_default { pinctrl-single,pins = < /* Slave 1 */ @@ -279,47 +320,6 @@ 0x204 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7) >; }; - }; - - matrix_keypad: matrix_keypad@0 { - compatible = "gpio-matrix-keypad"; - debounce-delay-ms = <5>; - col-scan-delay-us = <2>; - - row-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH /* Bank0, pin12 */ - &gpio0 13 GPIO_ACTIVE_HIGH /* Bank0, pin13 */ - &gpio0 14 GPIO_ACTIVE_HIGH /* Bank0, pin14 */ - &gpio0 15 GPIO_ACTIVE_HIGH>; /* Bank0, pin15 */ - - col-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH /* Bank3, pin9 */ - &gpio3 10 GPIO_ACTIVE_HIGH /* Bank3, pin10 */ - &gpio2 18 GPIO_ACTIVE_HIGH /* Bank2, pin18 */ - &gpio2 19 GPIO_ACTIVE_HIGH>; /* Bank2, pin19 */ - - linux,keymap = <0x00000201 /* P1 */ - 0x01000204 /* P4 */ - 0x02000207 /* P7 */ - 0x0300020a /* NUMERIC_STAR */ - 0x00010202 /* P2 */ - 0x01010205 /* P5 */ - 0x02010208 /* P8 */ - 0x03010200 /* P0 */ - 0x00020203 /* P3 */ - 0x01020206 /* P6 */ - 0x02020209 /* P9 */ - 0x0302020b /* NUMERIC_POUND */ - 0x00030067 /* UP */ - 0x0103006a /* RIGHT */ - 0x0203006c /* DOWN */ - 0x03030069>; /* LEFT */ - }; - - backlight { - compatible = "pwm-backlight"; - pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>; - brightness-levels = <0 51 53 56 62 75 101 152 255>; - default-brightness-level = <8>; - }; }; &mmc1 { diff --git a/arch/arm/boot/dts/am43xx-clocks.dtsi b/arch/arm/boot/dts/am43xx-clocks.dtsi index cfb49686ab6a..d0c0dfa4ec48 100644 --- a/arch/arm/boot/dts/am43xx-clocks.dtsi +++ b/arch/arm/boot/dts/am43xx-clocks.dtsi @@ -7,7 +7,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -&scrm_clocks { +&scm_clocks { sys_clkin_ck: sys_clkin_ck { #clock-cells = <0>; compatible = "ti,mux-clock"; diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index bd48dba16748..7128fad991ac 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -8,7 +8,6 @@ /dts-v1/; #include "dra74x.dtsi" -#include #include #include @@ -19,6 +18,7 @@ aliases { rtc0 = &mcp_rtc; rtc1 = &tps659038_rtc; + rtc2 = &rtc; }; memory { @@ -84,9 +84,10 @@ gpio_fan: gpio_fan { /* Based on 5v 500mA AFB02505HHB */ compatible = "gpio-fan"; - gpios = <&tps659038_gpio 1 GPIO_ACTIVE_HIGH>; + gpios = <&tps659038_gpio 2 GPIO_ACTIVE_HIGH>; gpio-fan,speed-map = <0 0>, <13000 1>; + #cooling-cells = <2>; }; extcon_usb1: extcon_usb1 { @@ -130,8 +131,8 @@ uart3_pins_default: uart3_pins_default { pinctrl-single,pins = < - 0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd.rxd */ - 0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd.txd */ + 0x3f8 (PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */ + 0x3fc (PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */ >; }; @@ -442,6 +443,7 @@ pinctrl-0 = <&tmp102_pins_default>; interrupt-parent = <&gpio7>; interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + #thermal-sensor-cells = <1>; }; }; @@ -454,7 +456,7 @@ mcp_rtc: rtc@6f { compatible = "microchip,mcp7941x"; reg = <0x6f>; - interrupts = ; /* IRQ_SYS_1N */ + interrupts = ; /* IRQ_SYS_1N */ pinctrl-names = "default"; pinctrl-0 = <&mcp79410_pins_default>; @@ -477,7 +479,7 @@ &uart3 { status = "okay"; interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, - <&dra7_pmx_core 0x248>; + <&dra7_pmx_core 0x3f8>; pinctrl-names = "default"; pinctrl-0 = <&uart3_pins_default>; @@ -548,6 +550,61 @@ pinctrl-0 = <&usb1_pins>; }; +&omap_dwc3_1 { + extcon = <&extcon_usb1>; +}; + +&omap_dwc3_2 { + extcon = <&extcon_usb2>; +}; + &usb2 { dr_mode = "peripheral"; }; + +&cpu_trips { + cpu_alert1: cpu_alert1 { + temperature = <50000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "active"; + }; +}; + +&cpu_cooling_maps { + map1 { + trip = <&cpu_alert1>; + cooling-device = <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; +}; + +&thermal_zones { + board_thermal: board_thermal { + polling-delay-passive = <1250>; /* milliseconds */ + polling-delay = <1500>; /* milliseconds */ + + /* sensor ID */ + thermal-sensors = <&tmp102 0>; + + board_trips: trips { + board_alert0: board_alert { + temperature = <40000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "active"; + }; + + board_crit: board_crit { + temperature = <105000>; /* millicelsius */ + hysteresis = <0>; /* millicelsius */ + type = "critical"; + }; + }; + + board_cooling_maps: cooling-maps { + map0 { + trip = <&board_alert0>; + cooling-device = + <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts index e993c46bd472..19f3bf271915 100644 --- a/arch/arm/boot/dts/armada-370-db.dts +++ b/arch/arm/boot/dts/armada-370-db.dts @@ -45,6 +45,15 @@ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR * OTHER DEALINGS IN THE SOFTWARE. + * + * Note: this Device Tree assumes that the bootloader has remapped the + * internal registers to 0xf1000000 (instead of the default + * 0xd0000000). The 0xf1000000 is the default used by the recent, + * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier + * boards were delivered with an older version of the bootloader that + * left internal registers mapped at 0xd0000000. If you are in this + * situation, you should either update your bootloader (preferred + * solution) or the below Device Tree should be adjusted. */ /dts-v1/; @@ -55,7 +64,7 @@ compatible = "marvell,a370-db", "marvell,armada370", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { @@ -64,7 +73,7 @@ }; soc { - ranges = ; internal-regs { diff --git a/arch/arm/boot/dts/armada-370-mirabox.dts b/arch/arm/boot/dts/armada-370-mirabox.dts index b10ceb488efe..0f40d5da28c3 100644 --- a/arch/arm/boot/dts/armada-370-mirabox.dts +++ b/arch/arm/boot/dts/armada-370-mirabox.dts @@ -51,7 +51,7 @@ compatible = "globalscale,mirabox", "marvell,armada370", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/armada-370-netgear-rn102.dts index 3f8cc3845a5e..a31207860f34 100644 --- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts +++ b/arch/arm/boot/dts/armada-370-netgear-rn102.dts @@ -53,7 +53,7 @@ compatible = "netgear,readynas-102", "marvell,armada370", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-370-netgear-rn104.dts b/arch/arm/boot/dts/armada-370-netgear-rn104.dts index 99eb8a014ac6..00540f292979 100644 --- a/arch/arm/boot/dts/armada-370-netgear-rn104.dts +++ b/arch/arm/boot/dts/armada-370-netgear-rn104.dts @@ -53,7 +53,7 @@ compatible = "netgear,readynas-104", "marvell,armada370", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-370-rd.dts b/arch/arm/boot/dts/armada-370-rd.dts index 6ae36a38beb2..19475e68b8e9 100644 --- a/arch/arm/boot/dts/armada-370-rd.dts +++ b/arch/arm/boot/dts/armada-370-rd.dts @@ -64,7 +64,7 @@ compatible = "marvell,a370-rd", "marvell,armada370", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-370-synology-ds213j.dts b/arch/arm/boot/dts/armada-370-synology-ds213j.dts index 59f74e66963f..b42b767763aa 100644 --- a/arch/arm/boot/dts/armada-370-synology-ds213j.dts +++ b/arch/arm/boot/dts/armada-370-synology-ds213j.dts @@ -67,8 +67,7 @@ "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; - stdout-path = &uart0; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi index 8a322ad57e5f..ec96f0b36346 100644 --- a/arch/arm/boot/dts/armada-370-xp.dtsi +++ b/arch/arm/boot/dts/armada-370-xp.dtsi @@ -59,8 +59,8 @@ compatible = "marvell,armada-370-xp"; aliases { - eth0 = ð0; - eth1 = ð1; + serial0 = &uart0; + serial1 = &uart1; }; cpus { @@ -73,6 +73,11 @@ }; }; + pmu { + compatible = "arm,cortex-a9-pmu"; + interrupts-extended = <&mpic 3>; + }; + soc { #address-cells = <2>; #size-cells = <1>; @@ -223,7 +228,7 @@ <0x20250 0x8>; }; - mpic: interrupt-controller@20000 { + mpic: interrupt-controller@20a00 { compatible = "marvell,mpic"; #interrupt-cells = <1>; #size-cells = <1>; diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/armada-370.dtsi index 27397f151def..00b50db57c9c 100644 --- a/arch/arm/boot/dts/armada-370.dtsi +++ b/arch/arm/boot/dts/armada-370.dtsi @@ -129,6 +129,7 @@ compatible = "marvell,aurora-outer-cache"; reg = <0x08000 0x1000>; cache-id-part = <0x100>; + cache-level = <2>; cache-unified; wt-override; }; @@ -232,7 +233,7 @@ reg = <0x18330 0x4>; }; - interrupt-controller@20000 { + interrupt-controller@20a00 { reg = <0x20a00 0x1d0>, <0x21870 0x58>; }; diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts index 0440891425c0..4eabc9c21f8d 100644 --- a/arch/arm/boot/dts/armada-375-db.dts +++ b/arch/arm/boot/dts/armada-375-db.dts @@ -55,7 +55,7 @@ compatible = "marvell,a375-db", "marvell,armada375"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi index ba3c57e0af72..f076ff856d8b 100644 --- a/arch/arm/boot/dts/armada-375.dtsi +++ b/arch/arm/boot/dts/armada-375.dtsi @@ -60,8 +60,8 @@ gpio0 = &gpio0; gpio1 = &gpio1; gpio2 = &gpio2; - ethernet0 = ð0; - ethernet1 = ð1; + serial0 = &uart0; + serial1 = &uart1; }; clocks { @@ -69,7 +69,7 @@ mainpll: mainpll { compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency = <2000000000>; + clock-frequency = <1000000000>; }; /* 25 MHz reference crystal */ refclk: oscillator { @@ -96,6 +96,11 @@ }; }; + pmu { + compatible = "arm,cortex-a9-pmu"; + interrupts-extended = <&mpic 3>; + }; + soc { compatible = "marvell,armada375-mbus", "simple-bus"; #address-cells = <2>; @@ -276,7 +281,7 @@ status = "disabled"; }; - serial@12000 { + uart0: serial@12000 { compatible = "snps,dw-apb-uart"; reg = <0x12000 0x100>; reg-shift = <2>; @@ -286,7 +291,7 @@ status = "disabled"; }; - serial@12100 { + uart1: serial@12100 { compatible = "snps,dw-apb-uart"; reg = <0x12100 0x100>; reg-shift = <2>; @@ -394,7 +399,7 @@ reg = <0x20000 0x100>, <0x20180 0x20>; }; - mpic: interrupt-controller@20000 { + mpic: interrupt-controller@20a00 { compatible = "marvell,mpic"; reg = <0x20a00 0x2d0>, <0x21070 0x58>; #interrupt-cells = <1>; diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/armada-385-db-ap.dts index 57b9119fb3e0..7219ac3a3d90 100644 --- a/arch/arm/boot/dts/armada-385-db-ap.dts +++ b/arch/arm/boot/dts/armada-385-db-ap.dts @@ -49,8 +49,7 @@ compatible = "marvell,a385-db-ap", "marvell,armada385", "marvell,armada38x"; chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &uart1; + stdout-path = "serial1:115200n8"; }; memory { @@ -126,6 +125,13 @@ status = "okay"; }; + pinctrl@18000 { + xhci0_vbus_pins: xhci0-vbus-pins { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + }; + ethernet@30000 { status = "okay"; phy = <&phy2>; @@ -150,6 +156,24 @@ phy = <&phy0>; phy-mode = "rgmii-id"; }; + + nfc: flash@d0000 { + status = "okay"; + #address-cells = <1>; + #size-cells = <1>; + + num-cs = <1>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + marvell,nand-keep-config; + marvell,nand-enable-arbiter; + nand-on-flash-bbt; + }; + + usb3@f0000 { + status = "okay"; + usb-phy = <&usb3_phy>; + }; }; pcie-controller { @@ -175,4 +199,20 @@ }; }; }; + + usb3_phy: usb3_phy { + compatible = "usb-nop-xceiv"; + vcc-supply = <®_xhci0_vbus>; + }; + + reg_xhci0_vbus: xhci0-vbus { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&xhci0_vbus_pins>; + regulator-name = "xhci0-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + }; }; diff --git a/arch/arm/boot/dts/armada-388-db.dts b/arch/arm/boot/dts/armada-388-db.dts index 16512efcd32c..51d1623de53e 100644 --- a/arch/arm/boot/dts/armada-388-db.dts +++ b/arch/arm/boot/dts/armada-388-db.dts @@ -54,7 +54,7 @@ "marvell,armada385", "marvell,armada380"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { @@ -99,7 +99,7 @@ phy-mode = "rgmii-id"; }; - usb@50000 { + usb@58000 { status = "ok"; }; diff --git a/arch/arm/boot/dts/armada-388-gp.dts b/arch/arm/boot/dts/armada-388-gp.dts index 590b383db323..78514ab0b47a 100644 --- a/arch/arm/boot/dts/armada-388-gp.dts +++ b/arch/arm/boot/dts/armada-388-gp.dts @@ -48,8 +48,7 @@ compatible = "marvell,a385-gp", "marvell,armada388", "marvell,armada380"; chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &uart0; + stdout-path = "serial0:115200n8"; }; memory { @@ -135,7 +134,7 @@ }; /* CON4 */ - usb@50000 { + usb@58000 { vcc-supply = <®_usb2_0_vbus>; status = "okay"; }; diff --git a/arch/arm/boot/dts/armada-388-rd.dts b/arch/arm/boot/dts/armada-388-rd.dts index d99baac72081..1dc6e2341cc2 100644 --- a/arch/arm/boot/dts/armada-388-rd.dts +++ b/arch/arm/boot/dts/armada-388-rd.dts @@ -55,7 +55,7 @@ "marvell,armada385","marvell,armada380"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { @@ -85,6 +85,16 @@ clock-frequency = <100000>; }; + sdhci@d8000 { + pinctrl-names = "default"; + pinctrl-0 = <&sdhci_pins>; + broken-cd; + no-1-8-v; + wp-inverted; + bus-width = <8>; + status = "okay"; + }; + serial@12000 { status = "okay"; }; diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi index 1dff30a81e24..218a2acd36e5 100644 --- a/arch/arm/boot/dts/armada-38x.dtsi +++ b/arch/arm/boot/dts/armada-38x.dtsi @@ -59,9 +59,13 @@ aliases { gpio0 = &gpio0; gpio1 = &gpio1; - ethernet0 = ð0; - ethernet1 = ð1; - ethernet2 = ð2; + serial0 = &uart0; + serial1 = &uart1; + }; + + pmu { + compatible = "arm,cortex-a9-pmu"; + interrupts-extended = <&mpic 3>; }; soc { @@ -216,7 +220,7 @@ status = "disabled"; }; - serial@12100 { + uart1: serial@12100 { compatible = "snps,dw-apb-uart"; reg = <0x12100 0x100>; reg-shift = <2>; @@ -368,7 +372,7 @@ reg = <0x20000 0x100>, <0x20180 0x20>; }; - mpic: interrupt-controller@20000 { + mpic: interrupt-controller@20a00 { compatible = "marvell,mpic"; reg = <0x20a00 0x2d0>, <0x21070 0x58>; #interrupt-cells = <1>; @@ -435,7 +439,7 @@ status = "disabled"; }; - usb@50000 { + usb@58000 { compatible = "marvell,orion-ehci"; reg = <0x58000 0x500>; interrupts = ; @@ -548,8 +552,11 @@ sdhci@d8000 { compatible = "marvell,armada-380-sdhci"; - reg = <0xd8000 0x1000>, <0xdc000 0x100>; - interrupts = <0 25 0x4>; + reg-names = "sdhci", "mbus", "conf-sdio3"; + reg = <0xd8000 0x1000>, + <0xdc000 0x100>, + <0x18454 0x4>; + interrupts = ; clocks = <&gateclk 17>; mrvl,clk-delay-cycles = <0x1F>; status = "disabled"; @@ -578,7 +585,7 @@ mainpll: mainpll { compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency = <2000000000>; + clock-frequency = <1000000000>; }; /* 25 MHz reference crystal */ diff --git a/arch/arm/boot/dts/armada-390.dtsi b/arch/arm/boot/dts/armada-390.dtsi new file mode 100644 index 000000000000..094e39c66039 --- /dev/null +++ b/arch/arm/boot/dts/armada-390.dtsi @@ -0,0 +1,57 @@ +/* + * Device Tree Include file for Marvell Armada 390 SoC. + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "armada-39x.dtsi" + +/ { + soc { + internal-regs { + pinctrl@18000 { + compatible = "marvell,mv88f6920-pinctrl"; + reg = <0x18000 0x20>; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-398-db.dts b/arch/arm/boot/dts/armada-398-db.dts new file mode 100644 index 000000000000..bbf83756c43c --- /dev/null +++ b/arch/arm/boot/dts/armada-398-db.dts @@ -0,0 +1,153 @@ +/* + * Device Tree Include file for Marvell Armada 398 Development Board + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "armada-398.dtsi" + +/ { + model = "Marvell Armada 398 Development Board"; + compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x80000000>; /* 2 GB */ + }; + + soc { + ranges = ; + + internal-regs { + spi@10680 { + status = "okay"; + pinctrl-0 = <&spi1_pins>; + pinctrl-names = "default"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "n25q128a13"; + reg = <0>; + spi-max-frequency = <108000000>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x400000>; + }; + + partition@400000 { + label = "Filesystem"; + reg = <0x400000 0x1000000>; + }; + }; + }; + + i2c@11000 { + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + status = "okay"; + clock-frequency = <100000>; + }; + + serial@12000 { + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + serial@12100 { + pinctrl-0 = <&uart1_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + flash@d0000 { + status = "okay"; + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + num-cs = <1>; + marvell,nand-keep-config; + marvell,nand-enable-arbiter; + nand-on-flash-bbt; + nand-ecc-strength = <8>; + nand-ecc-step-size = <512>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x800000>; + }; + partition@800000 { + label = "Linux"; + reg = <0x800000 0x800000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; + }; + }; + + pcie-controller { + status = "okay"; + + pcie@1,0 { + status = "okay"; + }; + + pcie@2,0 { + status = "okay"; + }; + + pcie@3,0 { + status = "okay"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-398.dtsi b/arch/arm/boot/dts/armada-398.dtsi new file mode 100644 index 000000000000..fdc25914e3a3 --- /dev/null +++ b/arch/arm/boot/dts/armada-398.dtsi @@ -0,0 +1,60 @@ +/* + * Device Tree Include file for Marvell Armada 398 SoC. + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "armada-39x.dtsi" + +/ { + compatible = "marvell,armada398", "marvell,armada390"; + + soc { + internal-regs { + pinctrl@18000 { + compatible = "marvell,mv88f6928-pinctrl"; + reg = <0x18000 0x20>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/armada-39x.dtsi new file mode 100644 index 000000000000..ecd1318109ba --- /dev/null +++ b/arch/arm/boot/dts/armada-39x.dtsi @@ -0,0 +1,508 @@ +/* + * Device Tree Include file for Marvell Armada 39x family of SoCs. + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "skeleton.dtsi" +#include +#include + +#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) + +/ { + model = "Marvell Armada 39x family SoC"; + compatible = "marvell,armada390"; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "marvell,armada-390-smp"; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <0>; + }; + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <1>; + }; + }; + + soc { + compatible = "marvell,armada390-mbus", "marvell,armadaxp-mbus", + "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + controller = <&mbusc>; + interrupt-parent = <&gic>; + pcie-mem-aperture = <0xe0000000 0x8000000>; + pcie-io-aperture = <0xe8000000 0x100000>; + + bootrom { + compatible = "marvell,bootrom"; + reg = ; + }; + + internal-regs { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>; + + L2: cache-controller@8000 { + compatible = "arm,pl310-cache"; + reg = <0x8000 0x1000>; + cache-unified; + cache-level = <2>; + }; + + scu@c000 { + compatible = "arm,cortex-a9-scu"; + reg = <0xc000 0x100>; + }; + + timer@c600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0xc600 0x20>; + interrupts = ; + clocks = <&coreclk 2>; + }; + + gic: interrupt-controller@d000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #size-cells = <0>; + interrupt-controller; + reg = <0xd000 0x1000>, + <0xc100 0x100>; + }; + + spi0: spi@10600 { + compatible = "marvell,orion-spi"; + reg = <0x10600 0x50>; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + interrupts = ; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + spi1: spi@10680 { + compatible = "marvell,orion-spi"; + reg = <0x10680 0x50>; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <1>; + interrupts = ; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c0: i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = ; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c1: i2c@11100 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11100 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = ; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c2: i2c@11200 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11200 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = ; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c3: i2c@11300 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11300 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = ; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + uart0: serial@12000 { + compatible = "snps,dw-apb-uart"; + reg = <0x12000 0x100>; + reg-shift = <2>; + interrupts = ; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + uart1: serial@12100 { + compatible = "snps,dw-apb-uart"; + reg = <0x12100 0x100>; + reg-shift = <2>; + interrupts = ; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + uart2: serial@12200 { + compatible = "snps,dw-apb-uart"; + reg = <0x12200 0x100>; + reg-shift = <2>; + interrupts = ; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + uart3: serial@12300 { + compatible = "snps,dw-apb-uart"; + reg = <0x12300 0x100>; + reg-shift = <2>; + interrupts = ; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + pinctrl@18000 { + i2c0_pins: i2c0-pins { + marvell,pins = "mpp2", "mpp3"; + marvell,function = "i2c0"; + }; + + uart0_pins: uart0-pins { + marvell,pins = "mpp0", "mpp1"; + marvell,function = "ua0"; + }; + + uart1_pins: uart1-pins { + marvell,pins = "mpp19", "mpp20"; + marvell,function = "ua1"; + }; + + spi1_pins: spi1-pins { + marvell,pins = "mpp56", "mpp57", "mpp58", "mpp59"; + marvell,function = "spi1"; + }; + + nand_pins: nand-pins { + marvell,pins = "mpp22", "mpp34", "mpp23", "mpp33", + "mpp38", "mpp28", "mpp40", "mpp42", + "mpp35", "mpp36", "mpp25", "mpp30", + "mpp32"; + marvell,function = "dev"; + }; + }; + + system-controller@18200 { + compatible = "marvell,armada-390-system-controller", + "marvell,armada-370-xp-system-controller"; + reg = <0x18200 0x100>; + }; + + gateclk: clock-gating-control@18220 { + compatible = "marvell,armada-390-gating-clock"; + reg = <0x18220 0x4>; + clocks = <&coreclk 0>; + #clock-cells = <1>; + }; + + coreclk: mvebu-sar@18600 { + compatible = "marvell,armada-390-core-clock"; + reg = <0x18600 0x04>; + #clock-cells = <1>; + }; + + mbusc: mbus-controller@20000 { + compatible = "marvell,mbus-controller"; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; + }; + + mpic: interrupt-controller@20a00 { + compatible = "marvell,mpic"; + reg = <0x20a00 0x2d0>, <0x21070 0x58>; + #interrupt-cells = <1>; + #size-cells = <1>; + interrupt-controller; + msi-controller; + interrupts = ; + }; + + timer@20300 { + compatible = "marvell,armada-380-timer", + "marvell,armada-xp-timer"; + reg = <0x20300 0x30>, <0x21040 0x30>; + interrupts-extended = <&gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, + <&mpic 5>, + <&mpic 6>; + clocks = <&coreclk 2>, <&coreclk 5>; + clock-names = "nbclk", "fixed"; + }; + + cpurst@20800 { + compatible = "marvell,armada-370-cpu-reset"; + reg = <0x20800 0x10>; + }; + + pmsu@22000 { + compatible = "marvell,armada-390-pmsu", + "marvell,armada-380-pmsu"; + reg = <0x22000 0x1000>; + }; + + xor@60800 { + compatible = "marvell,orion-xor"; + reg = <0x60800 0x100 + 0x60a00 0x100>; + clocks = <&gateclk 22>; + status = "okay"; + + xor00 { + interrupts = ; + dmacap,memcpy; + dmacap,xor; + }; + xor01 { + interrupts = ; + dmacap,memcpy; + dmacap,xor; + dmacap,memset; + }; + }; + + xor@60900 { + compatible = "marvell,orion-xor"; + reg = <0x60900 0x100 + 0x60b00 0x100>; + clocks = <&gateclk 28>; + status = "okay"; + + xor10 { + interrupts = ; + dmacap,memcpy; + dmacap,xor; + }; + xor11 { + interrupts = ; + dmacap,memcpy; + dmacap,xor; + dmacap,memset; + }; + }; + + flash@d0000 { + compatible = "marvell,armada370-nand"; + reg = <0xd0000 0x54>; + #address-cells = <1>; + #size-cells = <1>; + interrupts = ; + clocks = <&coredivclk 0>; + status = "disabled"; + }; + + sdhci@d8000 { + compatible = "marvell,armada-380-sdhci"; + reg = <0xd8000 0x1000>, <0xdc000 0x100>; + interrupts = ; + clocks = <&gateclk 17>; + mrvl,clk-delay-cycles = <0x1F>; + status = "disabled"; + }; + + coredivclk: clock@e4250 { + compatible = "marvell,armada-390-corediv-clock", + "marvell,armada-380-corediv-clock"; + reg = <0xe4250 0xc>; + #clock-cells = <1>; + clocks = <&mainpll>; + clock-output-names = "nand"; + }; + }; + + pcie-controller { + compatible = "marvell,armada-370-pcie"; + status = "disabled"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + msi-parent = <&mpic>; + bus-range = <0x00 0xff>; + + ranges = + <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 + 0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 + 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 + 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 + 0x82000000 0x1 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */ + 0x81000000 0x1 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO */ + 0x82000000 0x2 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */ + 0x81000000 0x2 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO */ + 0x82000000 0x3 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */ + 0x81000000 0x3 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO */ + 0x82000000 0x4 0 MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */ + 0x81000000 0x4 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO */>; + + /* + * This port can be either x4 or x1. When + * configured in x4 by the bootloader, then + * pcie@4,0 is not available. + */ + pcie@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x80000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 + 0x81000000 0 0 0x81000000 0x1 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 8>; + status = "disabled"; + }; + + /* x1 port */ + pcie@2,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 + 0x81000000 0 0 0x81000000 0x2 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 5>; + status = "disabled"; + }; + + /* x1 port */ + pcie@3,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x44000 0 0x2000>; + reg = <0x1800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0 + 0x81000000 0 0 0x81000000 0x3 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <2>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 6>; + status = "disabled"; + }; + + /* + * x1 port only available when pcie@1,0 is + * configured as a x1 port + */ + pcie@4,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x48000 0 0x2000>; + reg = <0x2000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0 + 0x81000000 0 0 0x81000000 0x4 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <3>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 7>; + status = "disabled"; + }; + }; + }; + + clocks { + /* 2 GHz fixed main PLL */ + mainpll: mainpll { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <1000000000>; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-xp-axpwifiap.dts b/arch/arm/boot/dts/armada-xp-axpwifiap.dts index c1fbab243609..dfd782b44e50 100644 --- a/arch/arm/boot/dts/armada-xp-axpwifiap.dts +++ b/arch/arm/boot/dts/armada-xp-axpwifiap.dts @@ -59,7 +59,7 @@ compatible = "marvell,rd-axpwifiap", "marvell,armadaxp-mv78230", "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts index 48bdafe17526..103782407618 100644 --- a/arch/arm/boot/dts/armada-xp-db.dts +++ b/arch/arm/boot/dts/armada-xp-db.dts @@ -64,7 +64,7 @@ compatible = "marvell,axp-db", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts index 206aebba01be..565227eacf06 100644 --- a/arch/arm/boot/dts/armada-xp-gp.dts +++ b/arch/arm/boot/dts/armada-xp-gp.dts @@ -65,7 +65,7 @@ compatible = "marvell,axp-gp", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts index 5fb3c8b687cf..06a6a6c1fdf7 100644 --- a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts +++ b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts @@ -54,8 +54,7 @@ "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; - stdout-path = &uart0; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts new file mode 100644 index 000000000000..a2cf2154dcdb --- /dev/null +++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts @@ -0,0 +1,393 @@ +/* + * Device Tree file for the Linksys WRT1900AC (Mamba). + * + * Note: this board is shipped with a new generation boot loader that + * remaps internal registers at 0xf1000000. Therefore, if earlyprintk + * is used, the CONFIG_DEBUG_MVEBU_UART0_ALTERNATE option should be + * used. + * + * Copyright (C) 2014 Imre Kaloz + * + * Based on armada-xp-axpwifiap.dts: + * + * Copyright (C) 2013 Marvell + * + * Thomas Petazzoni + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without + * any warranty of any kind, whether express or implied. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include +#include +#include "armada-xp-mv78230.dtsi" + +/ { + model = "Linksys WRT1900AC"; + compatible = "linksys,mamba", "marvell,armadaxp-mv78230", + "marvell,armadaxp", "marvell,armada-370-xp"; + + chosen { + bootargs = "console=ttyS0,115200"; + stdout-path = &uart0; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x00000000 0x00000000 0x10000000>; /* 256MB */ + }; + + soc { + ranges = ; + + pcie-controller { + status = "okay"; + + /* Etron EJ168 USB 3.0 controller */ + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + + /* First mini-PCIe port */ + pcie@2,0 { + /* Port 0, Lane 1 */ + status = "okay"; + }; + + /* Second mini-PCIe port */ + pcie@3,0 { + /* Port 0, Lane 3 */ + status = "okay"; + }; + }; + + internal-regs { + + /* J10: VCC, NC, RX, NC, TX, GND */ + serial@12000 { + status = "okay"; + }; + + sata@a0000 { + nr-ports = <1>; + status = "okay"; + }; + + ethernet@70000 { + pinctrl-0 = <&ge0_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii-id"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + ethernet@74000 { + pinctrl-0 = <&ge1_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii-id"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + /* USB part of the eSATA/USB 2.0 port */ + usb@50000 { + status = "okay"; + }; + + i2c@11000 { + status = "okay"; + clock-frequency = <100000>; + + tmp421@4c { + compatible = "ti,tmp421"; + reg = <0x4c>; + }; + + tlc59116@68 { + #address-cells = <1>; + #size-cells = <0>; + #gpio-cells = <2>; + compatible = "ti,tlc59116"; + reg = <0x68>; + + wan_amber@0 { + label = "mamba:amber:wan"; + reg = <0x0>; + }; + + wan_white@1 { + label = "mamba:white:wan"; + reg = <0x1>; + }; + + wlan_2g@2 { + label = "mamba:white:wlan_2g"; + reg = <0x2>; + }; + + wlan_5g@3 { + label = "mamba:white:wlan_5g"; + reg = <0x3>; + }; + + esata@4 { + label = "mamba:white:esata"; + reg = <0x4>; + }; + + usb2@5 { + label = "mamba:white:usb2"; + reg = <0x5>; + }; + + usb3_1@6 { + label = "mamba:white:usb3_1"; + reg = <0x6>; + }; + + usb3_2@7 { + label = "mamba:white:usb3_2"; + reg = <0x7>; + }; + + wps_white@8 { + label = "mamba:white:wps"; + reg = <0x8>; + }; + + wps_amber@9 { + label = "mamba:amber:wps"; + reg = <0x9>; + }; + }; + }; + + nand@d0000 { + status = "okay"; + num-cs = <1>; + marvell,nand-keep-config; + marvell,nand-enable-arbiter; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; /* 1MB */ + read-only; + }; + + partition@100000 { + label = "u_env"; + reg = <0x100000 0x40000>; /* 256KB */ + }; + + partition@140000 { + label = "s_env"; + reg = <0x140000 0x40000>; /* 256KB */ + }; + + partition@900000 { + label = "devinfo"; + reg = <0x900000 0x100000>; /* 1MB */ + read-only; + }; + + /* kernel1 overlaps with rootfs1 by design */ + partition@a00000 { + label = "kernel1"; + reg = <0xa00000 0x2800000>; /* 40MB */ + }; + + partition@d00000 { + label = "rootfs1"; + reg = <0xd00000 0x2500000>; /* 37MB */ + }; + + /* kernel2 overlaps with rootfs2 by design */ + partition@3200000 { + label = "kernel2"; + reg = <0x3200000 0x2800000>; /* 40MB */ + }; + + partition@3500000 { + label = "rootfs2"; + reg = <0x3500000 0x2500000>; /* 37MB */ + }; + + /* + * 38MB, last MB is for the BBT, not writable + */ + partition@5a00000 { + label = "syscfg"; + reg = <0x5a00000 0x2600000>; + }; + + /* + * Unused area between "s_env" and "devinfo". + * Moved here because otherwise the renumbered + * partitions would break the bootloader + * supplied bootargs + */ + partition@180000 { + label = "unused_area"; + reg = <0x180000 0x780000>; /* 7.5MB */ + }; + }; + + spi0: spi@10600 { + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "everspin,mr25h256"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <40000000>; + }; + }; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&keys_pin>; + pinctrl-names = "default"; + + button@1 { + label = "WPS"; + linux,code = ; + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>; + }; + + button@2 { + label = "Factory Reset Button"; + linux,code = ; + gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&power_led_pin>; + pinctrl-names = "default"; + + power { + label = "mamba:white:power"; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + gpio_fan { + /* SUNON HA4010V4-0000-C99 */ + compatible = "gpio-fan"; + gpios = <&gpio0 24 0>; + + gpio-fan,speed-map = <0 0 + 4500 1>; + }; + + dsa@0 { + compatible = "marvell,dsa"; + #address-cells = <2>; + #size-cells = <0>; + + dsa,ethernet = <ð0>; + dsa,mii-bus = <&mdio>; + + switch@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0>; /* MDIO address 0, switch 0 in tree */ + + port@0 { + reg = <0>; + label = "lan4"; + }; + + port@1 { + reg = <1>; + label = "lan3"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan1"; + }; + + port@4 { + reg = <4>; + label = "internet"; + }; + + port@5 { + reg = <5>; + label = "cpu"; + }; + }; + }; +}; + +&pinctrl { + + keys_pin: keys-pin { + marvell,pins = "mpp32", "mpp33"; + marvell,function = "gpio"; + }; + + power_led_pin: power-led-pin { + marvell,pins = "mpp40"; + marvell,function = "gpio"; + }; + + gpio_fan_pin: gpio-fan-pin { + marvell,pins = "mpp24"; + marvell,function = "gpio"; + }; +}; diff --git a/arch/arm/boot/dts/armada-xp-matrix.dts b/arch/arm/boot/dts/armada-xp-matrix.dts index 56f958eb1ede..f894bc83e957 100644 --- a/arch/arm/boot/dts/armada-xp-matrix.dts +++ b/arch/arm/boot/dts/armada-xp-matrix.dts @@ -52,7 +52,7 @@ compatible = "marvell,axp-matrix", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi index 4a7cbed79b07..8479fdc9e9c2 100644 --- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi @@ -57,7 +57,6 @@ gpio0 = &gpio0; gpio1 = &gpio1; gpio2 = &gpio2; - eth3 = ð3; }; cpus { diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/armada-xp-mv78460.dtsi index 36ce63a96cc9..661d54c81580 100644 --- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi @@ -57,7 +57,6 @@ gpio0 = &gpio0; gpio1 = &gpio1; gpio2 = &gpio2; - eth3 = ð3; }; diff --git a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts index 99cb9a8401b4..1516fc2627f9 100644 --- a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts +++ b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts @@ -53,7 +53,7 @@ compatible = "netgear,readynas-2120", "marvell,armadaxp-mv78230", "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts index 0c76d9f05fd0..990e8a2100f0 100644 --- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts +++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts @@ -54,7 +54,7 @@ compatible = "plathome,openblocks-ax3-4", "marvell,armadaxp-mv78260", "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { @@ -105,6 +105,10 @@ }; internal-regs { + rtc@10300 { + /* No crystal connected to the internal RTC */ + status = "disabled"; + }; serial@12000 { status = "okay"; }; diff --git a/arch/arm/boot/dts/armada-xp-synology-ds414.dts b/arch/arm/boot/dts/armada-xp-synology-ds414.dts index e9fb225169aa..6063428fa6a0 100644 --- a/arch/arm/boot/dts/armada-xp-synology-ds414.dts +++ b/arch/arm/boot/dts/armada-xp-synology-ds414.dts @@ -67,8 +67,7 @@ "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; - stdout-path = &uart0; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp.dtsi b/arch/arm/boot/dts/armada-xp.dtsi index 82917236a2fb..013d63f69e36 100644 --- a/arch/arm/boot/dts/armada-xp.dtsi +++ b/arch/arm/boot/dts/armada-xp.dtsi @@ -57,7 +57,8 @@ compatible = "marvell,armadaxp", "marvell,armada-370-xp"; aliases { - eth2 = ð2; + serial2 = &uart2; + serial3 = &uart3; }; soc { @@ -78,6 +79,7 @@ compatible = "marvell,aurora-system-cache"; reg = <0x08000 0x1000>; cache-id-part = <0x100>; + cache-level = <2>; cache-unified; wt-override; }; @@ -149,11 +151,11 @@ cpuclk: clock-complex@18700 { #clock-cells = <1>; compatible = "marvell,armada-xp-cpu-clock"; - reg = <0x18700 0xA0>, <0x1c054 0x10>; + reg = <0x18700 0x24>, <0x1c054 0x10>; clocks = <&coreclk 1>; }; - interrupt-controller@20000 { + interrupt-controller@20a00 { reg = <0x20a00 0x2d0>, <0x21070 0x58>; }; diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts index fec1fca2ad66..9991240b7438 100644 --- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts @@ -167,7 +167,13 @@ macb1: ethernet@f802c000 { phy-mode = "rmii"; + #address-cells = <1>; + #size-cells = <0>; status = "okay"; + + ethernet-phy@1 { + reg = <0x1>; + }; }; dbgu: serial@ffffee00 { @@ -188,6 +194,11 @@ ; }; + pinctrl_key_gpio: key_gpio_0 { + atmel,pins = + ; + }; + pinctrl_mmc0_cd: mmc0_cd { atmel,pins = ; @@ -276,6 +287,9 @@ gpio_keys { compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_key_gpio>; + bp3 { label = "PB_USER"; gpios = <&pioE 29 GPIO_ACTIVE_LOW>; diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts new file mode 100644 index 000000000000..c740e1a2a3a5 --- /dev/null +++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts @@ -0,0 +1,241 @@ +/* + * at91-sama5d4_xplained.dts - Device Tree file for SAMA5D4 Xplained board + * + * Copyright (C) 2015 Atmel, + * 2015 Josh Wu + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +/dts-v1/; +#include "sama5d4.dtsi" + +/ { + model = "Atmel SAMA5D4 Xplained"; + compatible = "atmel,sama5d4-xplained", "atmel,sama5d4", "atmel,sama5"; + + chosen { + bootargs = "console=ttyS0,115200 ignore_loglevel earlyprintk"; + }; + + memory { + reg = <0x20000000 0x20000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <12000000>; + }; + + slow_xtal { + clock-frequency = <32768>; + }; + + main_xtal { + clock-frequency = <12000000>; + }; + }; + + ahb { + apb { + spi0: spi@f8010000 { + cs-gpios = <&pioC 3 0>, <0>, <0>, <0>; + status = "okay"; + m25p80@0 { + compatible = "atmel,at25df321a"; + spi-max-frequency = <50000000>; + reg = <0>; + }; + }; + + i2c0: i2c@f8014000 { + status = "okay"; + }; + + macb0: ethernet@f8020000 { + phy-mode = "rmii"; + status = "okay"; + + phy0: ethernet-phy@1 { + interrupt-parent = <&pioE>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + reg = <1>; + }; + }; + + mmc1: mmc@fc000000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>; + status = "okay"; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioE 3 0>; + }; + }; + + usart3: serial@fc00c000 { + status = "okay"; + }; + + usart4: serial@fc010000 { + status = "okay"; + }; + + adc0: adc@fc034000 { + atmel,adc-vref = <3300>; + status = "okay"; + }; + + watchdog@fc068640 { + status = "okay"; + }; + + pinctrl@fc06a000 { + board { + pinctrl_mmc1_cd: mmc1_cd { + atmel,pins = + ; + }; + pinctrl_usba_vbus: usba_vbus { + atmel,pins = + ; + }; + pinctrl_key_gpio: key_gpio_0 { + atmel,pins = + ; + }; + }; + }; + }; + + usb0: gadget@00400000 { + atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usba_vbus>; + status = "okay"; + }; + + usb1: ohci@00500000 { + num-ports = <3>; + atmel,vbus-gpio = <0 + &pioE 11 GPIO_ACTIVE_HIGH + &pioE 14 GPIO_ACTIVE_HIGH + >; + status = "okay"; + }; + + usb2: ehci@00600000 { + status = "okay"; + }; + + nand0: nand@80000000 { + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + atmel,has-pmecc; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x40000>; + }; + + bootloader@40000 { + label = "bootloader"; + reg = <0x40000 0x80000>; + }; + + bootloaderenv@c0000 { + label = "bootloader env"; + reg = <0xc0000 0xc0000>; + }; + + dtb@180000 { + label = "device tree"; + reg = <0x180000 0x80000>; + }; + + kernel@200000 { + label = "kernel"; + reg = <0x200000 0x600000>; + }; + + rootfs@800000 { + label = "rootfs"; + reg = <0x800000 0x0f800000>; + }; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_key_gpio>; + + pb_user1 { + label = "pb_user1"; + gpios = <&pioE 8 GPIO_ACTIVE_HIGH>; + linux,code = <0x100>; + gpio-key,wakeup; + }; + }; + + leds { + compatible = "gpio-leds"; + status = "okay"; + + d8 { + label = "d8"; + gpios = <&pioD 30 GPIO_ACTIVE_HIGH>; + status = "disabled"; + }; + + d10 { + label = "d10"; + gpios = <&pioE 15 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/at91-sama5d4ek.dts index 9198b719d0ef..89ef4a540db5 100644 --- a/arch/arm/boot/dts/at91-sama5d4ek.dts +++ b/arch/arm/boot/dts/at91-sama5d4ek.dts @@ -115,6 +115,10 @@ }; }; + ssc0: ssc@f8008000 { + status = "okay"; + }; + spi0: spi@f8010000 { cs-gpios = <&pioC 3 0>, <0>, <0>, <0>; status = "okay"; @@ -127,6 +131,13 @@ i2c0: i2c@f8014000 { status = "okay"; + + wm8904: codec@1a { + compatible = "wlf,wm8904"; + reg = <0x1a>; + clocks = <&pck2>; + clock-names = "mclk"; + }; }; macb0: ethernet@f8020000 { @@ -171,6 +182,10 @@ atmel,pins = ; }; + pinctrl_pck2_as_audio_mck: pck2_as_audio_mck { + atmel,pins = + ; + }; pinctrl_usba_vbus: usba_vbus { atmel,pins = ; @@ -244,8 +259,6 @@ gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_key_gpio>; @@ -257,4 +270,42 @@ gpio-key,wakeup; }; }; + + leds { + compatible = "gpio-leds"; + status = "okay"; + + d8 { + label = "d8"; + /* PE28, conflicts with usart4 rts pin */ + gpios = <&pioE 28 GPIO_ACTIVE_LOW>; + }; + + d9 { + label = "d9"; + gpios = <&pioE 9 GPIO_ACTIVE_HIGH>; + }; + + d10 { + label = "d10"; + gpios = <&pioE 8 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; + + sound { + compatible = "atmel,asoc-wm8904"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck2_as_audio_mck>; + + atmel,model = "wm8904 @ SAMA5D4EK"; + atmel,audio-routing = + "Headphone Jack", "HPOUTL", + "Headphone Jack", "HPOUTR", + "IN1L", "Line In Jack", + "IN1R", "Line In Jack"; + + atmel,ssc-controller = <&ssc0>; + atmel,audio-codec = <&wm8904>; + }; }; diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi index 21c2b504f977..4fb333bd1f85 100644 --- a/arch/arm/boot/dts/at91rm9200.dtsi +++ b/arch/arm/boot/dts/at91rm9200.dtsi @@ -356,9 +356,13 @@ }; st: timer@fffffd00 { - compatible = "atmel,at91rm9200-st"; + compatible = "atmel,at91rm9200-st", "syscon", "simple-mfd"; reg = <0xfffffd00 0x100>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; + + watchdog { + compatible = "atmel,at91rm9200-wdt"; + }; }; rtc: rtc@fffffe00 { @@ -830,7 +834,7 @@ }; dbgu: serial@fffff200 { - compatible = "atmel,at91rm9200-usart"; + compatible = "atmel,at91rm9200-dbgu", "atmel,at91rm9200-usart"; reg = <0xfffff200 0x200>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi index 62d25b14deb8..d88fe62a2b2e 100644 --- a/arch/arm/boot/dts/at91sam9260.dtsi +++ b/arch/arm/boot/dts/at91sam9260.dtsi @@ -753,7 +753,7 @@ }; dbgu: serial@fffff200 { - compatible = "atmel,at91sam9260-usart"; + compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"; reg = <0xfffff200 0x200>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi index d55fdf2487ef..bf8d1856a55a 100644 --- a/arch/arm/boot/dts/at91sam9261.dtsi +++ b/arch/arm/boot/dts/at91sam9261.dtsi @@ -276,7 +276,7 @@ }; dbgu: serial@fffff200 { - compatible = "atmel,at91sam9260-usart"; + compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"; reg = <0xfffff200 0x200>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi index e4f61a979a57..111889b556cf 100644 --- a/arch/arm/boot/dts/at91sam9263.dtsi +++ b/arch/arm/boot/dts/at91sam9263.dtsi @@ -762,7 +762,7 @@ }; dbgu: serial@ffffee00 { - compatible = "atmel,at91sam9260-usart"; + compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"; reg = <0xffffee00 0x200>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/at91sam9g25.dtsi b/arch/arm/boot/dts/at91sam9g25.dtsi index 17b879990914..a7da0dd0c98f 100644 --- a/arch/arm/boot/dts/at91sam9g25.dtsi +++ b/arch/arm/boot/dts/at91sam9g25.dtsi @@ -7,6 +7,7 @@ */ #include "at91sam9x5.dtsi" +#include "at91sam9x5_isi.dtsi" #include "at91sam9x5_usart3.dtsi" #include "at91sam9x5_macb0.dtsi" diff --git a/arch/arm/boot/dts/at91sam9g25ek.dts b/arch/arm/boot/dts/at91sam9g25ek.dts index 1e4c49c584d3..707fd4ea58f5 100644 --- a/arch/arm/boot/dts/at91sam9g25ek.dts +++ b/arch/arm/boot/dts/at91sam9g25ek.dts @@ -16,10 +16,28 @@ ahb { apb { + spi0: spi@f0000000 { + status = "disabled"; + }; + + mmc1: mmc@f000c000 { + status = "disabled"; + }; + + i2c0: i2c@f8010000 { + ov2640: camera@0x30 { + status = "okay"; + }; + }; + macb0: ethernet@f802c000 { phy-mode = "rmii"; status = "okay"; }; + + isi: isi@f8048000 { + status = "okay"; + }; }; }; }; diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi index 8ec05b11298a..70e59c5ceb2f 100644 --- a/arch/arm/boot/dts/at91sam9g45.dtsi +++ b/arch/arm/boot/dts/at91sam9g45.dtsi @@ -893,7 +893,7 @@ }; dbgu: serial@ffffee00 { - compatible = "atmel,at91sam9260-usart"; + compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"; reg = <0xffffee00 0x200>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi index 0c53a375ba99..a9e35dfc12d9 100644 --- a/arch/arm/boot/dts/at91sam9n12.dtsi +++ b/arch/arm/boot/dts/at91sam9n12.dtsi @@ -757,7 +757,7 @@ }; dbgu: serial@fffff200 { - compatible = "atmel,at91sam9260-usart"; + compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"; reg = <0xfffff200 0x200>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; @@ -912,6 +912,15 @@ clocks = <&pwm_clk>; status = "disabled"; }; + + usb1: gadget@f803c000 { + compatible = "atmel,at91sam9260-udc"; + reg = <0xf803c000 0x4000>; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>; + clocks = <&udphs_clk>, <&udpck>; + clock-names = "pclk", "hclk"; + status = "disabled"; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts index 9575c0d895c9..6e067c8a3502 100644 --- a/arch/arm/boot/dts/at91sam9n12ek.dts +++ b/arch/arm/boot/dts/at91sam9n12ek.dts @@ -108,6 +108,13 @@ ; }; }; + + usb1 { + pinctrl_usb1_vbus_sense: usb1_vbus_sense { + atmel,pins = + ; /* PB16 gpio usb vbus sense, no pull up and deglitch */ + }; + }; }; spi0: spi@f0000000 { @@ -120,9 +127,20 @@ }; }; + usb1: gadget@f803c000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1_vbus_sense>; + atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + watchdog@fffffe40 { status = "okay"; }; + + rtc@fffffeb0 { + status = "okay"; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi index 40f645b8fe25..ebfd5ce9cb38 100644 --- a/arch/arm/boot/dts/at91sam9rl.dtsi +++ b/arch/arm/boot/dts/at91sam9rl.dtsi @@ -377,7 +377,7 @@ }; dbgu: serial@fffff200 { - compatible = "atmel,at91sam9260-usart"; + compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"; reg = <0xfffff200 0x200>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index d221179d0f1a..3aa56ae3410a 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -860,7 +860,7 @@ }; dbgu: serial@fffff200 { - compatible = "atmel,at91sam9260-usart"; + compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"; reg = <0xfffff200 0x200>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/at91sam9x5_isi.dtsi b/arch/arm/boot/dts/at91sam9x5_isi.dtsi index 98bc877a68ef..8fc45ca4dcb5 100644 --- a/arch/arm/boot/dts/at91sam9x5_isi.dtsi +++ b/arch/arm/boot/dts/at91sam9x5_isi.dtsi @@ -13,6 +13,37 @@ / { ahb { apb { + pinctrl@fffff400 { + isi { + pinctrl_isi_data_0_7: isi-0-data-0-7 { + atmel,pins = + ; /* ISI_VSYNC, conflicts with LCDDAT13 */ + }; + + pinctrl_isi_data_8_9: isi-0-data-8-9 { + atmel,pins = + ; /* ISI_D9, conflicts with LCDDAT9 */ + }; + + pinctrl_isi_data_10_11: isi-0-data-10-11 { + atmel,pins = + ; /* ISI_D11, conflicts with LCDDAT11 */ + }; + }; + }; + pmc: pmc@fffffc00 { periphck { isi_clk: isi_clk { @@ -21,6 +52,21 @@ }; }; }; + + isi: isi@f8048000 { + compatible = "atmel,at91sam9g45-isi"; + reg = <0xf8048000 0x4000>; + interrupts = <25 IRQ_TYPE_LEVEL_HIGH 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_isi_data_0_7>; + clocks = <&isi_clk>; + clock-names = "isi_clk"; + status = "disabled"; + port { + #address-cells = <1>; + #size-cells = <0>; + }; + }; }; }; }; diff --git a/arch/arm/boot/dts/at91sam9x5cm.dtsi b/arch/arm/boot/dts/at91sam9x5cm.dtsi index 229d6c24a9c4..26112ebd15fc 100644 --- a/arch/arm/boot/dts/at91sam9x5cm.dtsi +++ b/arch/arm/boot/dts/at91sam9x5cm.dtsi @@ -42,6 +42,10 @@ }; }; }; + + rtc@fffffeb0 { + status = "okay"; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9x5ek.dtsi b/arch/arm/boot/dts/at91sam9x5ek.dtsi index bd16bd360272..cc83a37a7311 100644 --- a/arch/arm/boot/dts/at91sam9x5ek.dtsi +++ b/arch/arm/boot/dts/at91sam9x5ek.dtsi @@ -59,6 +59,16 @@ status = "okay"; }; + isi: isi@f8048000 { + status = "disabled"; + port { + isi_0: endpoint@0 { + remote-endpoint = <&ov2640_0>; + bus-width = <8>; + }; + }; + }; + i2c0: i2c@f8010000 { status = "okay"; @@ -66,9 +76,47 @@ compatible = "wm8731"; reg = <0x1a>; }; + + ov2640: camera@0x30 { + compatible = "ovti,ov2640"; + reg = <0x30>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; + resetb-gpios = <&pioA 7 GPIO_ACTIVE_LOW>; + pwdn-gpios = <&pioA 13 GPIO_ACTIVE_HIGH>; + clocks = <&pck0>; + clock-names = "xvclk"; + assigned-clocks = <&pck0>; + assigned-clock-rates = <25000000>; + status = "disabled"; + + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + bus-width = <8>; + }; + }; + }; }; pinctrl@fffff400 { + camera_sensor { + pinctrl_pck0_as_isi_mck: pck0_as_isi_mck-0 { + atmel,pins = + ; /* ISI_MCK */ + }; + + pinctrl_sensor_power: sensor_power-0 { + atmel,pins = + ; + }; + + pinctrl_sensor_reset: sensor_reset-0 { + atmel,pins = + ; + }; + }; + mmc0 { pinctrl_board_mmc0: mmc0-board { atmel,pins = diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi index ff5fb6ab0b97..7b52c33ea69a 100644 --- a/arch/arm/boot/dts/bcm-cygnus.dtsi +++ b/arch/arm/boot/dts/bcm-cygnus.dtsi @@ -54,6 +54,42 @@ /include/ "bcm-cygnus-clock.dtsi" + pinctrl: pinctrl@0x0301d0c8 { + compatible = "brcm,cygnus-pinmux"; + reg = <0x0301d0c8 0x30>, + <0x0301d24c 0x2c>; + }; + + gpio_crmu: gpio@03024800 { + compatible = "brcm,cygnus-crmu-gpio"; + reg = <0x03024800 0x50>, + <0x03024008 0x18>; + #gpio-cells = <2>; + gpio-controller; + }; + + gpio_ccm: gpio@1800a000 { + compatible = "brcm,cygnus-ccm-gpio"; + reg = <0x1800a000 0x50>, + <0x0301d164 0x20>; + #gpio-cells = <2>; + gpio-controller; + interrupts = ; + interrupt-controller; + }; + + gpio_asiu: gpio@180a5000 { + compatible = "brcm,cygnus-asiu-gpio"; + reg = <0x180a5000 0x668>; + #gpio-cells = <2>; + gpio-controller; + + pinmux = <&pinctrl>; + + interrupt-controller; + interrupts = ; + }; + amba { #address-cells = <1>; #size-cells = <1>; @@ -90,6 +126,48 @@ status = "disabled"; }; + pcie0: pcie@18012000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18012000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>; + + linux,pci-domain = <0>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x28000000 0 0x00010000 + 0x82000000 0 0x20000000 0x20000000 0 0x04000000>; + + status = "disabled"; + }; + + pcie1: pcie@18013000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18013000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>; + + linux,pci-domain = <1>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x48000000 0 0x00010000 + 0x82000000 0 0x40000000 0x40000000 0 0x04000000>; + + status = "disabled"; + }; + uart0: serial@18020000 { compatible = "snps,dw-apb-uart"; reg = <0x18020000 0x100>; diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts index f18c9d9b2f2c..2ed9e5794785 100644 --- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts +++ b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts @@ -45,13 +45,13 @@ power0 { label = "bcm53xx:green:power"; gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>; - linux,default-trigger = "default-off"; + linux,default-trigger = "default-on"; }; power1 { label = "bcm53xx:amber:power"; gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; - linux,default-trigger = "default-on"; + linux,default-trigger = "default-off"; }; usb { diff --git a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts new file mode 100644 index 000000000000..ea26dd3ec03a --- /dev/null +++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts @@ -0,0 +1,77 @@ +/* + * Broadcom BCM470X / BCM5301X ARM platform code. + * DTS for Netgear R8000 + * + * Copyright (C) 2015 Rafał Miłecki + * + * Licensed under the GNU/GPL. See COPYING for details. + */ + +/dts-v1/; + +#include "bcm4708.dtsi" + +/ { + compatible = "netgear,r8000", "brcm,bcm4709", "brcm,bcm4708"; + model = "Netgear R8000 (BCM4709)"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + reg = <0x00000000 0x08000000>; + }; + + leds { + compatible = "gpio-leds"; + + power0 { + label = "bcm53xx:white:power"; + gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-on"; + }; + + power1 { + label = "bcm53xx:amber:power"; + gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; + + 5ghz-1 { + label = "bcm53xx:white:5ghz-1"; + gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; + + 2ghz { + label = "bcm53xx:white:2ghz"; + gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + rfkill { + label = "WiFi"; + linux,code = ; + gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "WPS"; + linux,code = ; + gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>; + }; + + restart { + label = "Reset"; + linux,code = ; + gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>; + }; + }; +}; diff --git a/arch/arm/boot/dts/bcm7445.dtsi b/arch/arm/boot/dts/bcm7445.dtsi index 0ca0f4e523d0..39ac7840d7ee 100644 --- a/arch/arm/boot/dts/bcm7445.dtsi +++ b/arch/arm/boot/dts/bcm7445.dtsi @@ -76,7 +76,7 @@ reg-shift = <2>; reg-io-width = <4>; interrupts = ; - clock-frequency = <0x4d3f640>; + clock-frequency = <81000000>; }; sun_top_ctrl: syscon@404000 { @@ -96,6 +96,18 @@ "syscon"; reg = <0x452000 0x100>; }; + + irq0_intc: interrupt-controller@40a780 { + compatible = "brcm,bcm7120-l2-intc"; + interrupt-parent = <&gic>; + #interrupt-cells = <1>; + reg = <0x40a780 0x8>; + interrupt-controller; + interrupts = , + ; + brcm,int-map-mask = <0x25c>, <0x7000000>; + brcm,int-fwd-mask = <0x70000>; + }; }; smpboot { diff --git a/arch/arm/boot/dts/bcm911360_entphn.dts b/arch/arm/boot/dts/bcm911360_entphn.dts index d2ee95280548..7db484323fd6 100644 --- a/arch/arm/boot/dts/bcm911360_entphn.dts +++ b/arch/arm/boot/dts/bcm911360_entphn.dts @@ -33,6 +33,7 @@ /dts-v1/; #include "bcm-cygnus.dtsi" +#include "dt-bindings/input/input.h" / { model = "Cygnus Enterprise Phone (BCM911360_ENTPHN)"; @@ -50,4 +51,16 @@ uart3: serial@18023000 { status = "okay"; }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + hook { + label = "HOOK"; + linux,code = ; + gpios = <&gpio_asiu 48 0>; + }; + }; }; diff --git a/arch/arm/boot/dts/bcm958300k.dts b/arch/arm/boot/dts/bcm958300k.dts index f1bb36f3975c..c9eb8565eac5 100644 --- a/arch/arm/boot/dts/bcm958300k.dts +++ b/arch/arm/boot/dts/bcm958300k.dts @@ -47,6 +47,14 @@ bootargs = "console=ttyS0,115200"; }; + pcie0: pcie@18012000 { + status = "okay"; + }; + + pcie1: pcie@18013000 { + status = "okay"; + }; + uart3: serial@18023000 { status = "okay"; }; diff --git a/arch/arm/boot/dts/bcm958305k.dts b/arch/arm/boot/dts/bcm958305k.dts new file mode 100644 index 000000000000..56b429abbedb --- /dev/null +++ b/arch/arm/boot/dts/bcm958305k.dts @@ -0,0 +1,53 @@ +/* + * BSD LICENSE + * + * Copyright(c) 2015 Broadcom Corporation. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Broadcom Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +/dts-v1/; + +#include "bcm-cygnus.dtsi" + +/ { + model = "Cygnus Wireless Audio (BCM958305K)"; + compatible = "brcm,bcm58305", "brcm,cygnus"; + + aliases { + serial0 = &uart3; + }; + + chosen { + stdout-path = &uart3; + bootargs = "console=ttyS0,115200"; + }; + + uart3: serial@18023000 { + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/dm8168-evm.dts index afe678f6d2e9..169a85578fc9 100644 --- a/arch/arm/boot/dts/dm8168-evm.dts +++ b/arch/arm/boot/dts/dm8168-evm.dts @@ -29,10 +29,10 @@ &dm816x_pinmux { mcspi1_pins: pinmux_mcspi1_pins { pinctrl-single,pins = < - DM816X_IOPAD(0x0a94, PIN_INPUT | MUX_MODE0) /* SPI_SCLK */ - DM816X_IOPAD(0x0a98, PIN_OUTPUT | MUX_MODE0) /* SPI_SCS0 */ - DM816X_IOPAD(0x0aa8, PIN_INPUT | MUX_MODE0) /* SPI_D0 */ - DM816X_IOPAD(0x0aac, PIN_INPUT | MUX_MODE0) /* SPI_D1 */ + DM816X_IOPAD(0x0a94, MUX_MODE0) /* SPI_SCLK */ + DM816X_IOPAD(0x0a98, MUX_MODE0) /* SPI_SCS0 */ + DM816X_IOPAD(0x0aa8, MUX_MODE0) /* SPI_D0 */ + DM816X_IOPAD(0x0aac, MUX_MODE0) /* SPI_D1 */ >; }; @@ -52,13 +52,13 @@ usb0_pins: pinmux_usb0_pins { pinctrl-single,pins = < - DM816X_IOPAD(0x0d00, MUX_MODE0) /* USB0_DRVVBUS */ + DM816X_IOPAD(0x0d04, MUX_MODE0) /* USB0_DRVVBUS */ >; }; - usb1_pins: pinmux_usb0_pins { + usb1_pins: pinmux_usb1_pins { pinctrl-single,pins = < - DM816X_IOPAD(0x0d04, MUX_MODE0) /* USB1_DRVVBUS */ + DM816X_IOPAD(0x0d08, MUX_MODE0) /* USB1_DRVVBUS */ >; }; }; diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi index f35715bc6992..de8427be830a 100644 --- a/arch/arm/boot/dts/dm816x.dtsi +++ b/arch/arm/boot/dts/dm816x.dtsi @@ -396,6 +396,29 @@ mentor,num-eps = <16>; mentor,ram-bits = <12>; mentor,power = <500>; + + dmas = <&cppi41dma 0 0 &cppi41dma 1 0 + &cppi41dma 2 0 &cppi41dma 3 0 + &cppi41dma 4 0 &cppi41dma 5 0 + &cppi41dma 6 0 &cppi41dma 7 0 + &cppi41dma 8 0 &cppi41dma 9 0 + &cppi41dma 10 0 &cppi41dma 11 0 + &cppi41dma 12 0 &cppi41dma 13 0 + &cppi41dma 14 0 &cppi41dma 0 1 + &cppi41dma 1 1 &cppi41dma 2 1 + &cppi41dma 3 1 &cppi41dma 4 1 + &cppi41dma 5 1 &cppi41dma 6 1 + &cppi41dma 7 1 &cppi41dma 8 1 + &cppi41dma 9 1 &cppi41dma 10 1 + &cppi41dma 11 1 &cppi41dma 12 1 + &cppi41dma 13 1 &cppi41dma 14 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; }; usb1: usb@47401800 { @@ -413,6 +436,43 @@ mentor,num-eps = <16>; mentor,ram-bits = <12>; mentor,power = <500>; + + dmas = <&cppi41dma 15 0 &cppi41dma 16 0 + &cppi41dma 17 0 &cppi41dma 18 0 + &cppi41dma 19 0 &cppi41dma 20 0 + &cppi41dma 21 0 &cppi41dma 22 0 + &cppi41dma 23 0 &cppi41dma 24 0 + &cppi41dma 25 0 &cppi41dma 26 0 + &cppi41dma 27 0 &cppi41dma 28 0 + &cppi41dma 29 0 &cppi41dma 15 1 + &cppi41dma 16 1 &cppi41dma 17 1 + &cppi41dma 18 1 &cppi41dma 19 1 + &cppi41dma 20 1 &cppi41dma 21 1 + &cppi41dma 22 1 &cppi41dma 23 1 + &cppi41dma 24 1 &cppi41dma 25 1 + &cppi41dma 26 1 &cppi41dma 27 1 + &cppi41dma 28 1 &cppi41dma 29 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + cppi41dma: dma-controller@47402000 { + compatible = "ti,am3359-cppi41"; + reg = <0x47400000 0x1000 + 0x47402000 0x1000 + 0x47403000 0x1000 + 0x47404000 0x4000>; + reg-names = "glue", "controller", "scheduler", "queuemgr"; + interrupts = <17>; + interrupt-names = "glue"; + #dma-cells = <2>; + #dma-channels = <30>; + #dma-requests = <256>; }; }; diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/dove-cubox.dts index aae7efc09b0b..e6fa251e17b9 100644 --- a/arch/arm/boot/dts/dove-cubox.dts +++ b/arch/arm/boot/dts/dove-cubox.dts @@ -87,6 +87,7 @@ /* connect xtal input to 25MHz reference */ clocks = <&ref25>; + clock-names = "xtal"; /* connect xtal input as source of pll0 and pll1 */ silabs,pll-source = <0 0>, <1 0>; diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi index a5441d5482a6..9ad829523a13 100644 --- a/arch/arm/boot/dts/dove.dtsi +++ b/arch/arm/boot/dts/dove.dtsi @@ -1,5 +1,8 @@ /include/ "skeleton.dtsi" +#include +#include + #define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) / { @@ -61,7 +64,7 @@ 0x82000000 0x2 0x0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 Mem */ 0x81000000 0x2 0x0 MBUS_ID(0x08, 0xe0) 0 1 0>; /* Port 1.0 I/O */ - pcie-port@0 { + pcie0: pcie-port@0 { device_type = "pci"; status = "disabled"; assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; @@ -79,7 +82,7 @@ interrupt-map = <0 0 0 0 &intc 16>; }; - pcie-port@1 { + pcie1: pcie-port@1 { device_type = "pci"; status = "disabled"; assigned-addresses = <0x82002800 0 0x80000 0 0x2000>; @@ -154,7 +157,7 @@ uart2: serial@12200 { compatible = "ns16550a"; - reg = <0x12000 0x100>; + reg = <0x12200 0x100>; reg-shift = <2>; interrupts = <9>; clocks = <&core_clk 0>; @@ -163,7 +166,7 @@ uart3: serial@12300 { compatible = "ns16550a"; - reg = <0x12100 0x100>; + reg = <0x12300 0x100>; reg-shift = <2>; interrupts = <10>; clocks = <&core_clk 0>; @@ -448,6 +451,11 @@ marvell,function = "gpio"; }; + pmx_pcie1_clkreq: pmx-pcie1-clkreq { + marvell,pins = "mpp9"; + marvell,function = "pex1"; + }; + pmx_gpio_10: pmx-gpio-10 { marvell,pins = "mpp10"; marvell,function = "gpio"; @@ -458,6 +466,11 @@ marvell,function = "gpio"; }; + pmx_pcie0_clkreq: pmx-pcie0-clkreq { + marvell,pins = "mpp11"; + marvell,function = "pex0"; + }; + pmx_gpio_12: pmx-gpio-12 { marvell,pins = "mpp12"; marvell,function = "gpio"; @@ -563,6 +576,18 @@ marvell,function = "gpio"; }; + pmx_spi1_4_7: pmx-spi1-4-7 { + marvell,pins = "mpp4", "mpp5", + "mpp6", "mpp7"; + marvell,function = "spi1"; + }; + + pmx_spi1_20_23: pmx-spi1-20-23 { + marvell,pins = "mpp20", "mpp21", + "mpp22", "mpp23"; + marvell,function = "spi1"; + }; + pmx_uart1: pmx-uart1 { marvell,pins = "mpp_uart1"; marvell,function = "uart1"; @@ -582,6 +607,36 @@ marvell,pins = "mpp_nand"; marvell,function = "gpo"; }; + + pmx_i2c1: pmx-i2c1 { + marvell,pins = "mpp17", "mpp19"; + marvell,function = "twsi"; + }; + + pmx_i2c2: pmx-i2c2 { + marvell,pins = "mpp_audio1"; + marvell,function = "twsi"; + }; + + pmx_ssp_i2c2: pmx-ssp-i2c2 { + marvell,pins = "mpp_audio1"; + marvell,function = "ssp/twsi"; + }; + + pmx_i2cmux_0: pmx-i2cmux-0 { + marvell,pins = "twsi"; + marvell,function = "twsi-opt1"; + }; + + pmx_i2cmux_1: pmx-i2cmux-1 { + marvell,pins = "twsi"; + marvell,function = "twsi-opt2"; + }; + + pmx_i2cmux_2: pmx-i2cmux-2 { + marvell,pins = "twsi"; + marvell,function = "twsi-opt3"; + }; }; core_clk: core-clocks@d0214 { diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index b1bd06c6c2a8..aa465904f6cc 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -541,6 +541,14 @@ }; }; +&omap_dwc3_1 { + extcon = <&extcon_usb1>; +}; + +&omap_dwc3_2 { + extcon = <&extcon_usb2>; +}; + &usb1 { dr_mode = "peripheral"; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index a0afce7ad482..f03a091cd076 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -102,17 +102,101 @@ interrupts-extended = <&crossbar_mpu GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, <&wakeupgen GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; - prm: prm@4ae06000 { - compatible = "ti,dra7-prm"; - reg = <0x4ae06000 0x3000>; - interrupts = ; + l4_cfg: l4@4a000000 { + compatible = "ti,dra7-l4-cfg", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x4a000000 0x22c000>; - prm_clocks: clocks { + scm: scm@2000 { + compatible = "ti,dra7-scm-core", "simple-bus"; + reg = <0x2000 0x2000>; #address-cells = <1>; - #size-cells = <0>; + #size-cells = <1>; + ranges = <0 0x2000 0x2000>; + + scm_conf: scm_conf@0 { + compatible = "syscon"; + reg = <0x0 0x1400>; + #address-cells = <1>; + #size-cells = <1>; + + pbias_regulator: pbias_regulator { + compatible = "ti,pbias-omap"; + reg = <0xe00 0x4>; + syscon = <&scm_conf>; + pbias_mmc_reg: pbias_mmc_omap5 { + regulator-name = "pbias_mmc_omap5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; + }; + }; + + dra7_pmx_core: pinmux@1400 { + compatible = "ti,dra7-padconf", + "pinctrl-single"; + reg = <0x1400 0x0464>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x3fffffff>; + }; }; - prm_clockdomains: clockdomains { + cm_core_aon: cm_core_aon@5000 { + compatible = "ti,dra7-cm-core-aon"; + reg = <0x5000 0x2000>; + + cm_core_aon_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + cm_core_aon_clockdomains: clockdomains { + }; + }; + + cm_core: cm_core@8000 { + compatible = "ti,dra7-cm-core"; + reg = <0x8000 0x3000>; + + cm_core_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + cm_core_clockdomains: clockdomains { + }; + }; + }; + + l4_wkup: l4@4ae00000 { + compatible = "ti,dra7-l4-wkup", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x4ae00000 0x3f000>; + + counter32k: counter@4000 { + compatible = "ti,omap-counter32k"; + reg = <0x4000 0x40>; + ti,hwmods = "counter_32k"; + }; + + prm: prm@6000 { + compatible = "ti,dra7-prm"; + reg = <0x6000 0x3000>; + interrupts = ; + + prm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + prm_clockdomains: clockdomains { + }; }; }; @@ -185,36 +269,16 @@ }; }; - cm_core_aon: cm_core_aon@4a005000 { - compatible = "ti,dra7-cm-core-aon"; - reg = <0x4a005000 0x2000>; - - cm_core_aon_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - cm_core_aon_clockdomains: clockdomains { - }; - }; - - cm_core: cm_core@4a008000 { - compatible = "ti,dra7-cm-core"; - reg = <0x4a008000 0x3000>; - - cm_core_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - cm_core_clockdomains: clockdomains { - }; - }; - - counter32k: counter@4ae04000 { - compatible = "ti,omap-counter32k"; - reg = <0x4ae04000 0x40>; - ti,hwmods = "counter_32k"; + bandgap: bandgap@4a0021e0 { + reg = <0x4a0021e0 0xc + 0x4a00232c 0xc + 0x4a002380 0x2c + 0x4a0023C0 0x3c + 0x4a002564 0x8 + 0x4a002574 0x50>; + compatible = "ti,dra752-bandgap"; + interrupts = ; + #thermal-sensor-cells = <1>; }; dra7_ctrl_core: ctrl_core@4a002000 { @@ -227,28 +291,6 @@ reg = <0x4a002e00 0x7c>; }; - pbias_regulator: pbias_regulator { - compatible = "ti,pbias-omap"; - reg = <0 0x4>; - syscon = <&dra7_ctrl_general>; - pbias_mmc_reg: pbias_mmc_omap5 { - regulator-name = "pbias_mmc_omap5"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3000000>; - }; - }; - - dra7_pmx_core: pinmux@4a003400 { - compatible = "ti,dra7-padconf", "pinctrl-single"; - reg = <0x4a003400 0x0464>; - #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - pinctrl-single,register-width = <32>; - pinctrl-single,function-mask = <0x3fffffff>; - }; - sdma: dma-controller@4a056000 { compatible = "ti,omap4430-sdma"; reg = <0x4a056000 0x1000>; @@ -666,7 +708,6 @@ reg = <0x48820000 0x80>; interrupts = ; ti,hwmods = "timer5"; - ti,timer-dsp; }; timer6: timer@48822000 { @@ -674,8 +715,6 @@ reg = <0x48822000 0x80>; interrupts = ; ti,hwmods = "timer6"; - ti,timer-dsp; - ti,timer-pwm; }; timer7: timer@48824000 { @@ -683,7 +722,6 @@ reg = <0x48824000 0x80>; interrupts = ; ti,hwmods = "timer7"; - ti,timer-dsp; }; timer8: timer@48826000 { @@ -691,8 +729,6 @@ reg = <0x48826000 0x80>; interrupts = ; ti,hwmods = "timer8"; - ti,timer-dsp; - ti,timer-pwm; }; timer9: timer@4803e000 { @@ -714,7 +750,6 @@ reg = <0x48088000 0x80>; interrupts = ; ti,hwmods = "timer11"; - ti,timer-pwm; }; timer13: timer@48828000 { @@ -876,7 +911,7 @@ ti,clock-cycles = <16>; reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>, - <0x4ae06014 0x4>, <0x4a003b20 0x8>, + <0x4ae06014 0x4>, <0x4a003b20 0xc>, <0x4ae0c158 0x4>; reg-names = "setup-address", "control-address", "int-address", "efuse-address", @@ -909,7 +944,7 @@ ti,clock-cycles = <16>; reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>, - <0x4ae06010 0x4>, <0x4a0025cc 0x8>, + <0x4ae06010 0x4>, <0x4a0025cc 0xc>, <0x4a002470 0x4>; reg-names = "setup-address", "control-address", "int-address", "efuse-address", @@ -942,7 +977,7 @@ ti,clock-cycles = <16>; reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>, - <0x4ae06010 0x4>, <0x4a0025e0 0x8>, + <0x4ae06010 0x4>, <0x4a0025e0 0xc>, <0x4a00246c 0x4>; reg-names = "setup-address", "control-address", "int-address", "efuse-address", @@ -975,7 +1010,7 @@ ti,clock-cycles = <16>; reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>, - <0x4ae06010 0x4>, <0x4a003b08 0x8>, + <0x4ae06010 0x4>, <0x4a003b08 0xc>, <0x4ae0c154 0x4>; reg-names = "setup-address", "control-address", "int-address", "efuse-address", @@ -1168,7 +1203,7 @@ status = "disabled"; }; - rtc@48838000 { + rtc: rtc@48838000 { compatible = "ti,am3352-rtc"; reg = <0x48838000 0x100>; interrupts = , @@ -1419,7 +1454,7 @@ compatible = "ti,dra7-d_can"; ti,hwmods = "dcan1"; reg = <0x4ae3c000 0x2000>; - syscon-raminit = <&dra7_ctrl_core 0x558 0>; + syscon-raminit = <&scm_conf 0x558 0>; interrupts = ; clocks = <&dcan1_sys_clk_mux>; status = "disabled"; @@ -1429,12 +1464,23 @@ compatible = "ti,dra7-d_can"; ti,hwmods = "dcan2"; reg = <0x48480000 0x2000>; - syscon-raminit = <&dra7_ctrl_core 0x558 1>; + syscon-raminit = <&scm_conf 0x558 1>; interrupts = ; clocks = <&sys_clkin1>; status = "disabled"; }; }; + + thermal_zones: thermal-zones { + #include "omap4-cpu-thermal.dtsi" + #include "omap5-gpu-thermal.dtsi" + #include "omap5-core-thermal.dtsi" + }; + +}; + +&cpu_thermal { + polling-delay = <500>; /* milliseconds */ }; /include/ "dra7xx-clocks.dtsi" diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index daf28110d487..ce0390f081d9 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -377,6 +377,14 @@ phy-supply = <&ldo4_reg>; }; +&omap_dwc3_1 { + extcon = <&extcon_usb1>; +}; + +&omap_dwc3_2 { + extcon = <&extcon_usb2>; +}; + &usb1 { dr_mode = "peripheral"; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/dra72x.dtsi b/arch/arm/boot/dts/dra72x.dtsi index f7fb0d0ef25a..03d742f8d572 100644 --- a/arch/arm/boot/dts/dra72x.dtsi +++ b/arch/arm/boot/dts/dra72x.dtsi @@ -20,6 +20,11 @@ device_type = "cpu"; compatible = "arm,cortex-a15"; reg = <0>; + + /* cooling options */ + cooling-min-level = <0>; + cooling-max-level = <2>; + #cooling-cells = <2>; /* min followed by max */ }; }; diff --git a/arch/arm/boot/dts/dra74x.dtsi b/arch/arm/boot/dts/dra74x.dtsi index 00eeed789b4b..cc560a70926f 100644 --- a/arch/arm/boot/dts/dra74x.dtsi +++ b/arch/arm/boot/dts/dra74x.dtsi @@ -31,6 +31,11 @@ clock-names = "cpu"; clock-latency = <300000>; /* From omap-cpufreq driver */ + + /* cooling options */ + cooling-min-level = <0>; + cooling-max-level = <2>; + #cooling-cells = <2>; /* min followed by max */ }; cpu@1 { device_type = "cpu"; diff --git a/arch/arm/boot/dts/dra7xx-clocks.dtsi b/arch/arm/boot/dts/dra7xx-clocks.dtsi index 99b09a44e269..3b933f74d000 100644 --- a/arch/arm/boot/dts/dra7xx-clocks.dtsi +++ b/arch/arm/boot/dts/dra7xx-clocks.dtsi @@ -1493,6 +1493,14 @@ ti,dividers = <1>, <8>; }; + clkout2_clk: clkout2_clk { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&clkoutmux2_clk_mux>; + ti,bit-shift = <8>; + reg = <0x06b0>; + }; + l3init_960m_gfclk: l3init_960m_gfclk { #clock-cells = <0>; compatible = "ti,gate-clock"; diff --git a/arch/arm/boot/dts/emev2-kzm9d.dts b/arch/arm/boot/dts/emev2-kzm9d.dts index 667d323e80a3..19446273e4a7 100644 --- a/arch/arm/boot/dts/emev2-kzm9d.dts +++ b/arch/arm/boot/dts/emev2-kzm9d.dts @@ -94,3 +94,16 @@ vdd33a-supply = <®_3p3v>; }; }; + +&pfc { + uart1_pins: uart@e1030000 { + renesas,groups = "uart1_ctrl", "uart1_data"; + renesas,function = "uart1"; + }; +}; + +&uart1 { + pinctrl-0 = <&uart1_pins>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/emev2.dtsi b/arch/arm/boot/dts/emev2.dtsi index cc7bfe0ba40a..bb45694d91bc 100644 --- a/arch/arm/boot/dts/emev2.dtsi +++ b/arch/arm/boot/dts/emev2.dtsi @@ -169,12 +169,18 @@ clock-names = "sclk"; }; + pfc: pfc@e0140200 { + compatible = "renesas,pfc-emev2"; + reg = <0xe0140200 0x100>; + }; + gpio0: gpio@e0050000 { compatible = "renesas,em-gio"; reg = <0xe0050000 0x2c>, <0xe0050040 0x20>; interrupts = <0 67 IRQ_TYPE_LEVEL_HIGH>, <0 68 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; + gpio-ranges = <&pfc 0 0 32>; #gpio-cells = <2>; ngpios = <32>; interrupt-controller; @@ -186,6 +192,7 @@ interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>, <0 70 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; + gpio-ranges = <&pfc 0 32 32>; #gpio-cells = <2>; ngpios = <32>; interrupt-controller; @@ -197,6 +204,7 @@ interrupts = <0 71 IRQ_TYPE_LEVEL_HIGH>, <0 72 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; + gpio-ranges = <&pfc 0 64 32>; #gpio-cells = <2>; ngpios = <32>; interrupt-controller; @@ -208,6 +216,7 @@ interrupts = <0 73 IRQ_TYPE_LEVEL_HIGH>, <0 74 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; + gpio-ranges = <&pfc 0 96 32>; #gpio-cells = <2>; ngpios = <32>; interrupt-controller; @@ -219,6 +228,7 @@ interrupts = <0 75 IRQ_TYPE_LEVEL_HIGH>, <0 76 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; + gpio-ranges = <&pfc 0 128 31>; #gpio-cells = <2>; ngpios = <31>; interrupt-controller; diff --git a/arch/arm/boot/dts/exynos3250.dtsi b/arch/arm/boot/dts/exynos3250.dtsi index 14ab515aa83c..e3bfb11c6ef8 100644 --- a/arch/arm/boot/dts/exynos3250.dtsi +++ b/arch/arm/boot/dts/exynos3250.dtsi @@ -176,6 +176,10 @@ compatible = "samsung,exynos3250-cmu"; reg = <0x10030000 0x20000>; #clock-cells = <1>; + assigned-clocks = <&cmu CLK_MOUT_ACLK_400_MCUISP_SUB>, + <&cmu CLK_MOUT_ACLK_266_SUB>; + assigned-clock-parents = <&cmu CLK_FIN_PLL>, + <&cmu CLK_FIN_PLL>; }; cmu_dmc: clock-controller@105C0000 { diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi index adb4f6a97a1d..d6b49e5b32e9 100644 --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi @@ -9,6 +9,7 @@ #include #include +#include #include "exynos4412.dtsi" / { @@ -75,10 +76,18 @@ }; }; + emmc_pwrseq: pwrseq { + pinctrl-0 = <&sd1_cd>; + pinctrl-names = "default"; + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpk1 2 1>; + }; + mmc@12550000 { pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; pinctrl-names = "default"; vmmc-supply = <&ldo20_reg &buck8_reg>; + mmc-pwrseq = <&emmc_pwrseq>; status = "okay"; num-slots = <1>; @@ -97,6 +106,8 @@ rtc@10070000 { status = "okay"; + clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; + clock-names = "rtc", "rtc_src"; }; g2d@10800000 { @@ -472,6 +483,12 @@ }; }; +/* RSTN signal for eMMC */ +&sd1_cd { + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; +}; + &pinctrl_1 { gpio_power_key: power_key { samsung,pins = "gpx1-3"; diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts index b9aeec430527..1eca97ee4bd6 100644 --- a/arch/arm/boot/dts/exynos5250-snow.dts +++ b/arch/arm/boot/dts/exynos5250-snow.dts @@ -29,6 +29,7 @@ chosen { bootargs = "console=tty1"; + stdout-path = "serial3:115200n8"; }; gpio-keys { @@ -183,7 +184,20 @@ powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>; reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>; edid-emulation = <5>; - panel = <&panel>; + + ports { + port@0 { + bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + + port@1 { + bridge_in: endpoint { + remote-endpoint = <&dp_out>; + }; + }; + }; }; }; @@ -228,6 +242,20 @@ compatible = "auo,b116xw03"; power-supply = <&fet6>; backlight = <&backlight>; + + port { + panel_in: endpoint { + remote-endpoint = <&bridge_out>; + }; + }; + }; + + mmc3_pwrseq: mmc3_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpx0 2 GPIO_ACTIVE_LOW>, /* WIFI_RSTn */ + <&gpx0 1 GPIO_ACTIVE_LOW>; /* WIFI_EN */ + clocks = <&max77686 MAX77686_CLK_PMIC>; + clock-names = "ext_clock"; }; }; @@ -242,7 +270,14 @@ samsung,link-rate = <0x0a>; samsung,lane-count = <2>; samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>; - bridge = <&ptn3460>; + + ports { + port@0 { + dp_out: endpoint { + remote-endpoint = <&bridge_in>; + }; + }; + }; }; &ehci { @@ -531,17 +566,34 @@ status = "okay"; num-slots = <1>; broken-cd; + cap-sdio-irq; + keep-power-in-suspend; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <2 3>; samsung,dw-mshc-ddr-timing = <1 2>; pinctrl-names = "default"; - pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>; + pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4 &wifi_en &wifi_rst>; bus-width = <4>; cap-sd-highspeed; + mmc-pwrseq = <&mmc3_pwrseq>; }; &pinctrl_0 { + wifi_en: wifi-en { + samsung,pins = "gpx0-1"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + wifi_rst: wifi-rst { + samsung,pins = "gpx0-2"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + power_key_irq: power-key-irq { samsung,pins = "gpx1-3"; samsung,pin-function = <0xf>; diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts index f02775487cd4..d03f9b8d376d 100644 --- a/arch/arm/boot/dts/exynos5250-spring.dts +++ b/arch/arm/boot/dts/exynos5250-spring.dts @@ -25,6 +25,7 @@ chosen { bootargs = "console=tty1"; + stdout-path = "serial3:115200n8"; }; gpio-keys { @@ -429,7 +430,6 @@ &mmc_0 { status = "okay"; num-slots = <1>; - supports-highspeed; broken-cd; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; @@ -437,11 +437,8 @@ samsung,dw-mshc-ddr-timing = <1 2>; pinctrl-names = "default"; pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>; - - slot@0 { - reg = <0>; - bus-width = <8>; - }; + bus-width = <8>; + cap-mmc-highspeed; }; /* @@ -451,7 +448,6 @@ &mmc_1 { status = "okay"; num-slots = <1>; - supports-highspeed; broken-cd; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; @@ -459,11 +455,8 @@ samsung,dw-mshc-ddr-timing = <1 2>; pinctrl-names = "default"; pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_cd &sd1_bus4>; - - slot@0 { - reg = <0>; - bus-width = <4>; - }; + bus-width = <4>; + cap-sd-highspeed; }; &pinctrl_0 { @@ -490,7 +483,7 @@ power_key_irq: power-key-irq { samsung,pins = "gpx1-3"; - samsung,pin-function = <0>; + samsung,pin-function = <0xf>; samsung,pin-pud = <0>; samsung,pin-drv = <0>; }; @@ -518,7 +511,7 @@ lid_irq: lid-irq { samsung,pins = "gpx3-5"; - samsung,pin-function = <0>; + samsung,pin-function = <0xf>; samsung,pin-pud = <0>; samsung,pin-drv = <0>; }; diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi index 77f656eb8e6b..257e2f10525d 100644 --- a/arch/arm/boot/dts/exynos5250.dtsi +++ b/arch/arm/boot/dts/exynos5250.dtsi @@ -143,7 +143,7 @@ compatible = "samsung,exynos4210-mct"; reg = <0x101C0000 0x800>; interrupt-controller; - #interrups-cells = <2>; + #interrupt-cells = <2>; interrupt-parent = <&mct_map>; interrupts = <0 0>, <1 0>, <2 0>, <3 0>, <4 0>, <5 0>; diff --git a/arch/arm/boot/dts/exynos5420-arndale-octa.dts b/arch/arm/boot/dts/exynos5420-arndale-octa.dts index db2c1c4cd900..b82b6fa15f48 100644 --- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts +++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts @@ -55,7 +55,7 @@ samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; pinctrl-names = "default"; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>; vmmc-supply = <&ldo10_reg>; bus-width = <8>; cap-mmc-highspeed; @@ -68,7 +68,7 @@ samsung,dw-mshc-sdr-timing = <2 3>; samsung,dw-mshc-ddr-timing = <1 2>; pinctrl-names = "default"; - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; vmmc-supply = <&ldo19_reg>; vqmmc-supply = <&ldo13_reg>; bus-width = <4>; diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts index c47bb70665c1..146e71118a72 100644 --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts @@ -43,6 +43,10 @@ pinctrl-names = "default"; }; + chosen { + stdout-path = "serial3:115200n8"; + }; + fixed-rate-clocks { oscclk { compatible = "samsung,exynos5420-oscclk"; @@ -118,6 +122,19 @@ compatible = "auo,b116xw03"; power-supply = <&tps65090_fet6>; backlight = <&backlight>; + + port { + panel_in: endpoint { + remote-endpoint = <&bridge_out>; + }; + }; + }; + + mmc1_pwrseq: mmc1_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpx0 0 GPIO_ACTIVE_LOW>; /* WIFI_EN */ + clocks = <&max77802 MAX77802_CLK_32K_CP>; + clock-names = "ext_clock"; }; }; @@ -137,7 +154,14 @@ samsung,link-rate = <0x06>; samsung,lane-count = <2>; samsung,hpd-gpio = <&gpx2 6 0>; - bridge = <&ps8625>; + + ports { + port@0 { + dp_out: endpoint { + remote-endpoint = <&bridge_in>; + }; + }; + }; }; &fimd { @@ -581,6 +605,8 @@ interrupt-parent = <&gpx0>; pinctrl-names = "default"; pinctrl-0 = <&max98090_irq>; + clocks = <&pmu_system_controller 0>; + clock-names = "mclk"; }; light-sensor@44 { @@ -595,8 +621,22 @@ sleep-gpios = <&gpx3 5 GPIO_ACTIVE_HIGH>; reset-gpios = <&gpy7 7 GPIO_ACTIVE_HIGH>; lane-count = <2>; - panel = <&panel>; use-external-pwm; + + ports { + port@0 { + bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + + port@1 { + bridge_in: endpoint { + remote-endpoint = <&dp_out>; + }; + }; + }; + }; }; @@ -659,11 +699,33 @@ samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; + samsung,dw-mshc-hs400-timing = <0 2>; + samsung,read-strobe-delay = <90>; pinctrl-names = "default"; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_rclk>; bus-width = <8>; }; +&mmc_1 { + status = "okay"; + num-slots = <1>; + broken-cd; + cap-sdio-irq; + keep-power-in-suspend; + card-detect-delay = <200>; + clock-frequency = <400000000>; + samsung,dw-mshc-ciu-div = <1>; + samsung,dw-mshc-sdr-timing = <0 1>; + samsung,dw-mshc-ddr-timing = <0 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd1_clk>, <&sd1_cmd>, <&sd1_int>, <&sd1_bus1>, + <&sd1_bus4>, <&sd1_bus8>, <&wifi_en>; + bus-width = <4>; + cap-sd-highspeed; + mmc-pwrseq = <&mmc1_pwrseq>; + vqmmc-supply = <&buck10_reg>; +}; + &mmc_2 { status = "okay"; num-slots = <1>; @@ -674,7 +736,7 @@ samsung,dw-mshc-sdr-timing = <2 3>; samsung,dw-mshc-ddr-timing = <1 2>; pinctrl-names = "default"; - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; bus-width = <4>; }; @@ -683,6 +745,13 @@ pinctrl-names = "default"; pinctrl-0 = <&mask_tpm_reset>; + wifi_en: wifi-en { + samsung,pins = "gpx0-0"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + max98090_irq: max98090-irq { samsung,pins = "gpx0-2"; samsung,pin-function = <0>; @@ -770,6 +839,29 @@ }; }; +&pinctrl_1 { + /* Adjust WiFi drive strengths lower for EMI */ + sd1_clk: sd1-clk { + samsung,pin-drv = <2>; + }; + + sd1_cmd: sd1-cmd { + samsung,pin-drv = <2>; + }; + + sd1_bus1: sd1-bus-width1 { + samsung,pin-drv = <2>; + }; + + sd1_bus4: sd1-bus-width4 { + samsung,pin-drv = <2>; + }; + + sd1_bus8: sd1-bus-width8 { + samsung,pin-drv = <2>; + }; +}; + &pinctrl_2 { pmic_dvs_2: pmic-dvs-2 { samsung,pins = "gpj4-2"; diff --git a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi index ba686e40eac7..8b153166ebdb 100644 --- a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi +++ b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi @@ -201,6 +201,13 @@ samsung,pin-drv = <3>; }; + sd0_rclk: sd0-rclk { + samsung,pins = "gpc0-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <1>; + samsung,pin-drv = <3>; + }; + sd1_cmd: sd1-cmd { samsung,pins = "gpc1-1"; samsung,pin-function = <2>; diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts index 8be3d7b489ff..9103f2381a6d 100644 --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts @@ -80,8 +80,11 @@ samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; + samsung,dw-mshc-hs400-timing = <0 2>; + samsung,read-strobe-delay = <90>; pinctrl-names = "default"; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 + &sd0_rclk>; bus-width = <8>; cap-mmc-highspeed; }; @@ -93,7 +96,7 @@ samsung,dw-mshc-sdr-timing = <2 3>; samsung,dw-mshc-ddr-timing = <1 2>; pinctrl-names = "default"; - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; bus-width = <4>; cap-sd-highspeed; }; diff --git a/arch/arm/boot/dts/exynos5420-trip-points.dtsi b/arch/arm/boot/dts/exynos5420-trip-points.dtsi index 5d31fc140823..2180a0152c9b 100644 --- a/arch/arm/boot/dts/exynos5420-trip-points.dtsi +++ b/arch/arm/boot/dts/exynos5420-trip-points.dtsi @@ -28,7 +28,7 @@ trips { type = "active"; }; cpu-crit-0 { - temperature = <1200000>; /* millicelsius */ + temperature = <120000>; /* millicelsius */ hysteresis = <0>; /* millicelsius */ type = "critical"; }; diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi index b3d2d53820e3..45317538bbae 100644 --- a/arch/arm/boot/dts/exynos5420.dtsi +++ b/arch/arm/boot/dts/exynos5420.dtsi @@ -221,7 +221,7 @@ compatible = "samsung,exynos4210-mct"; reg = <0x101C0000 0x800>; interrupt-controller; - #interrups-cells = <1>; + #interrupt-cells = <1>; interrupt-parent = <&mct_map>; interrupts = <0>, <1>, <2>, <3>, <4>, <5>, <6>, <7>, <8>, <9>, <10>, <11>; @@ -251,6 +251,8 @@ compatible = "samsung,exynos4210-pd"; reg = <0x10044000 0x20>; #power-domain-cells = <0>; + clocks = <&clock CLK_GSCL0>, <&clock CLK_GSCL1>; + clock-names = "asb0", "asb1"; }; isp_pd: power-domain@10044020 { @@ -283,9 +285,11 @@ <&clock CLK_MOUT_SW_ACLK300>, <&clock CLK_MOUT_USER_ACLK300_DISP1>, <&clock CLK_MOUT_SW_ACLK400>, - <&clock CLK_MOUT_USER_ACLK400_DISP1>; + <&clock CLK_MOUT_USER_ACLK400_DISP1>, + <&clock CLK_FIMD1>, <&clock CLK_MIXER>; clock-names = "oscclk", "pclk0", "clk0", - "pclk1", "clk1", "pclk2", "clk2"; + "pclk1", "clk1", "pclk2", "clk2", + "asb0", "asb1"; }; pinctrl_0: pinctrl@13400000 { @@ -532,6 +536,7 @@ clock-names = "dp"; phys = <&dp_phy>; phy-names = "dp"; + power-domains = <&disp_pd>; }; mipi_phy: video-phy@10040714 { diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3.dts b/arch/arm/boot/dts/exynos5422-odroidxu3.dts index a519c863248d..edc25cf1d717 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts +++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts @@ -264,6 +264,13 @@ }; }; + emmc_pwrseq: pwrseq { + pinctrl-0 = <&emmc_nrst_pin>; + pinctrl-names = "default"; + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpd1 0 1>; + }; + i2c_2: i2c@12C80000 { samsung,i2c-sda-delay = <100>; samsung,i2c-max-bus-freq = <66000>; @@ -298,13 +305,14 @@ &mmc_0 { status = "okay"; + mmc-pwrseq = <&emmc_pwrseq>; broken-cd; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; pinctrl-names = "default"; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>; bus-width = <8>; cap-mmc-highspeed; }; @@ -316,7 +324,7 @@ samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; pinctrl-names = "default"; - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; bus-width = <4>; cap-sd-highspeed; }; @@ -330,6 +338,15 @@ }; }; +&pinctrl_1 { + emmc_nrst_pin: emmc-nrst { + samsung,pins = "gpd1-0"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; +}; + &usbdrd_dwc3_0 { dr_mode = "host"; }; diff --git a/arch/arm/boot/dts/exynos5440-trip-points.dtsi b/arch/arm/boot/dts/exynos5440-trip-points.dtsi index 48adfa8f4300..356e963edf11 100644 --- a/arch/arm/boot/dts/exynos5440-trip-points.dtsi +++ b/arch/arm/boot/dts/exynos5440-trip-points.dtsi @@ -18,7 +18,7 @@ trips { type = "active"; }; cpu-crit-0 { - temperature = <1050000>; /* millicelsius */ + temperature = <105000>; /* millicelsius */ hysteresis = <0>; /* millicelsius */ type = "critical"; }; diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts index 06737c60d333..02eb8b15374f 100644 --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts @@ -42,6 +42,10 @@ pinctrl-names = "default"; }; + chosen { + stdout-path = "serial3:115200n8"; + }; + fixed-rate-clocks { oscclk { compatible = "samsung,exynos5420-oscclk"; @@ -119,6 +123,13 @@ power-supply = <&tps65090_fet6>; backlight = <&backlight>; }; + + mmc1_pwrseq: mmc1_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpx0 0 GPIO_ACTIVE_LOW>; /* WIFI_EN */ + clocks = <&max77802 MAX77802_CLK_32K_CP>; + clock-names = "ext_clock"; + }; }; &adc { @@ -581,6 +592,8 @@ interrupt-parent = <&gpx0>; pinctrl-names = "default"; pinctrl-0 = <&max98091_irq>; + clocks = <&pmu_system_controller 0>; + clock-names = "mclk"; }; light-sensor@44 { @@ -641,18 +654,41 @@ num-slots = <1>; broken-cd; mmc-hs200-1_8v; + mmc-hs400-1_8v; cap-mmc-highspeed; non-removable; card-detect-delay = <200>; - clock-frequency = <400000000>; + clock-frequency = <800000000>; samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; + samsung,dw-mshc-hs400-timing = <0 2>; + samsung,read-strobe-delay = <90>; pinctrl-names = "default"; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_rclk>; bus-width = <8>; }; +&mmc_1 { + status = "okay"; + num-slots = <1>; + broken-cd; + cap-sdio-irq; + keep-power-in-suspend; + card-detect-delay = <200>; + clock-frequency = <400000000>; + samsung,dw-mshc-ciu-div = <1>; + samsung,dw-mshc-sdr-timing = <0 1>; + samsung,dw-mshc-ddr-timing = <0 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd1_clk>, <&sd1_cmd>, <&sd1_int>, <&sd1_bus1>, + <&sd1_bus4>, <&sd1_bus8>, <&wifi_en>; + bus-width = <4>; + cap-sd-highspeed; + mmc-pwrseq = <&mmc1_pwrseq>; + vqmmc-supply = <&buck10_reg>; +}; + &mmc_2 { status = "okay"; num-slots = <1>; @@ -663,7 +699,7 @@ samsung,dw-mshc-sdr-timing = <2 3>; samsung,dw-mshc-ddr-timing = <1 2>; pinctrl-names = "default"; - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; bus-width = <4>; }; @@ -672,6 +708,13 @@ pinctrl-names = "default"; pinctrl-0 = <&mask_tpm_reset>; + wifi_en: wifi-en { + samsung,pins = "gpx0-0"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + max98091_irq: max98091-irq { samsung,pins = "gpx0-2"; samsung,pin-function = <0>; @@ -759,6 +802,29 @@ }; }; +&pinctrl_1 { + /* Adjust WiFi drive strengths lower for EMI */ + sd1_clk: sd1-clk { + samsung,pin-drv = <2>; + }; + + sd1_cmd: sd1-cmd { + samsung,pin-drv = <2>; + }; + + sd1_bus1: sd1-bus-width1 { + samsung,pin-drv = <2>; + }; + + sd1_bus4: sd1-bus-width4 { + samsung,pin-drv = <2>; + }; + + sd1_bus8: sd1-bus-width8 { + samsung,pin-drv = <2>; + }; +}; + &pinctrl_2 { pmic_dvs_2: pmic-dvs-2 { samsung,pins = "gpj4-2"; diff --git a/arch/arm/boot/dts/hip04.dtsi b/arch/arm/boot/dts/hip04.dtsi index 238814596a87..44044f275115 100644 --- a/arch/arm/boot/dts/hip04.dtsi +++ b/arch/arm/boot/dts/hip04.dtsi @@ -275,7 +275,6 @@ compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0 0xe3c42000 0 0x1000>; - coresight-default-sink; clocks = <&clk_375m>; clock-names = "apb_pclk"; port { diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/imx23-olinuxino.dts index 7e6eef2488e8..82045398bf1f 100644 --- a/arch/arm/boot/dts/imx23-olinuxino.dts +++ b/arch/arm/boot/dts/imx23-olinuxino.dts @@ -12,6 +12,7 @@ */ /dts-v1/; +#include #include "imx23.dtsi" / { @@ -93,6 +94,7 @@ ahb@80080000 { usb0: usb@80080000 { + dr_mode = "host"; vbus-supply = <®_usb0_vbus>; status = "okay"; }; @@ -122,7 +124,7 @@ user { label = "green"; - gpios = <&gpio2 1 1>; + gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>; }; }; }; diff --git a/arch/arm/boot/dts/imx25-pdk.dts b/arch/arm/boot/dts/imx25-pdk.dts index 9c21b1583762..dd45e6971bc3 100644 --- a/arch/arm/boot/dts/imx25-pdk.dts +++ b/arch/arm/boot/dts/imx25-pdk.dts @@ -75,6 +75,27 @@ mux-int-port = <1>; mux-ext-port = <4>; }; + + wvga: display { + model = "CLAA057VC01CW"; + bits-per-pixel = <16>; + fsl,pcr = <0xfa208b80>; + bus-width = <18>; + native-mode = <&wvga_timings>; + display-timings { + wvga_timings: 640x480 { + hactive = <640>; + vactive = <480>; + hback-porch = <45>; + hfront-porch = <114>; + hsync-len = <1>; + vback-porch = <33>; + vfront-porch = <11>; + vsync-len = <1>; + clock-frequency = <25200000>; + }; + }; + }; }; &audmux { @@ -190,6 +211,33 @@ >; }; + pinctrl_lcd: lcdgrp { + fsl,pins = < + MX25_PAD_LD0__LD0 0xe0 + MX25_PAD_LD1__LD1 0xe0 + MX25_PAD_LD2__LD2 0xe0 + MX25_PAD_LD3__LD3 0xe0 + MX25_PAD_LD4__LD4 0xe0 + MX25_PAD_LD5__LD5 0xe0 + MX25_PAD_LD6__LD6 0xe0 + MX25_PAD_LD7__LD7 0xe0 + MX25_PAD_LD8__LD8 0xe0 + MX25_PAD_LD9__LD9 0xe0 + MX25_PAD_LD10__LD10 0xe0 + MX25_PAD_LD11__LD11 0xe0 + MX25_PAD_LD12__LD12 0xe0 + MX25_PAD_LD13__LD13 0xe0 + MX25_PAD_LD14__LD14 0xe0 + MX25_PAD_LD15__LD15 0xe0 + MX25_PAD_GPIO_E__LD16 0xe0 + MX25_PAD_GPIO_F__LD17 0xe0 + MX25_PAD_HSYNC__HSYNC 0xe0 + MX25_PAD_VSYNC__VSYNC 0xe0 + MX25_PAD_LSCLK__LSCLK 0xe0 + MX25_PAD_OE_ACD__OE_ACD 0xe0 + MX25_PAD_CONTRAST__CONTRAST 0xe0 + >; + }; pinctrl_uart1: uart1grp { fsl,pins = < @@ -202,6 +250,16 @@ }; }; +&lcdc { + display = <&wvga>; + fsl,lpccr = <0x00a903ff>; + fsl,lscr1 = <0x00120300>; + fsl,dmacr = <0x00020010>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd>; + status = "okay"; +}; + &nfc { nand-on-flash-bbt; status = "okay"; diff --git a/arch/arm/boot/dts/imx25-pinfunc.h b/arch/arm/boot/dts/imx25-pinfunc.h index 88eebb15da6a..7c4b9f2f9aad 100644 --- a/arch/arm/boot/dts/imx25-pinfunc.h +++ b/arch/arm/boot/dts/imx25-pinfunc.h @@ -17,48 +17,69 @@ * */ +#define MX25_PAD_TDO__TDO 0x000 0x3e8 0x000 0x00 0x000 + #define MX25_PAD_A10__A10 0x008 0x000 0x000 0x00 0x000 #define MX25_PAD_A10__GPIO_4_0 0x008 0x000 0x000 0x05 0x000 #define MX25_PAD_A13__A13 0x00c 0x22C 0x000 0x00 0x000 #define MX25_PAD_A13__GPIO_4_1 0x00c 0x22C 0x000 0x05 0x000 +#define MX25_PAD_A13__LCDC_CLS 0x00c 0x22C 0x000 0x07 0x000 #define MX25_PAD_A14__A14 0x010 0x230 0x000 0x10 0x000 #define MX25_PAD_A14__GPIO_2_0 0x010 0x230 0x000 0x15 0x000 +#define MX25_PAD_A14__SIM1_CLK1 0x010 0x230 0x000 0x16 0x000 +#define MX25_PAD_A14__LCDC_SPL 0x010 0x230 0x000 0x17 0x000 #define MX25_PAD_A15__A15 0x014 0x234 0x000 0x10 0x000 #define MX25_PAD_A15__GPIO_2_1 0x014 0x234 0x000 0x15 0x000 +#define MX25_PAD_A15__SIM1_RST1 0x014 0x234 0x000 0x16 0x000 +#define MX25_PAD_A15__LCDC_PS 0x014 0x234 0x000 0x17 0x000 #define MX25_PAD_A16__A16 0x018 0x000 0x000 0x10 0x000 #define MX25_PAD_A16__GPIO_2_2 0x018 0x000 0x000 0x15 0x000 +#define MX25_PAD_A16__SIM1_VEN1 0x018 0x000 0x000 0x16 0x000 +#define MX25_PAD_A16__LCDC_REV 0x018 0x000 0x000 0x17 0x000 #define MX25_PAD_A17__A17 0x01c 0x238 0x000 0x10 0x000 #define MX25_PAD_A17__GPIO_2_3 0x01c 0x238 0x000 0x15 0x000 +#define MX25_PAD_A17__SIM1_TX 0x01c 0x238 0x554 0x16 0x000 +#define MX25_PAD_A17__FEC_TX_ERR 0x01c 0x238 0x000 0x17 0x000 #define MX25_PAD_A18__A18 0x020 0x23c 0x000 0x10 0x000 #define MX25_PAD_A18__GPIO_2_4 0x020 0x23c 0x000 0x15 0x000 +#define MX25_PAD_A18__SIM1_PD1 0x020 0x23c 0x550 0x16 0x000 #define MX25_PAD_A18__FEC_COL 0x020 0x23c 0x504 0x17 0x000 #define MX25_PAD_A19__A19 0x024 0x240 0x000 0x10 0x000 -#define MX25_PAD_A19__FEC_RX_ER 0x024 0x240 0x518 0x17 0x000 #define MX25_PAD_A19__GPIO_2_5 0x024 0x240 0x000 0x15 0x000 +#define MX25_PAD_A19__SIM1_RX1 0x024 0x240 0x54c 0x16 0x000 +#define MX25_PAD_A19__FEC_RX_ERR 0x024 0x240 0x518 0x17 0x000 #define MX25_PAD_A20__A20 0x028 0x244 0x000 0x10 0x000 #define MX25_PAD_A20__GPIO_2_6 0x028 0x244 0x000 0x15 0x000 +#define MX25_PAD_A20__SIM2_CLK1 0x028 0x244 0x000 0x16 0x000 #define MX25_PAD_A20__FEC_RDATA2 0x028 0x244 0x50c 0x17 0x000 #define MX25_PAD_A21__A21 0x02c 0x248 0x000 0x10 0x000 #define MX25_PAD_A21__GPIO_2_7 0x02c 0x248 0x000 0x15 0x000 +#define MX25_PAD_A21__SIM2_RST1 0x02c 0x248 0x000 0x16 0x000 #define MX25_PAD_A21__FEC_RDATA3 0x02c 0x248 0x510 0x17 0x000 #define MX25_PAD_A22__A22 0x030 0x000 0x000 0x10 0x000 #define MX25_PAD_A22__GPIO_2_8 0x030 0x000 0x000 0x15 0x000 +#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x17 0x000 +#define MX25_PAD_A22__SIM2_VEN1 0x030 0x000 0x000 0x16 0x000 +#define MX25_PAD_A22__FEC_TDATA2 0x030 0x000 0x000 0x17 0x000 #define MX25_PAD_A23__A23 0x034 0x24c 0x000 0x10 0x000 #define MX25_PAD_A23__GPIO_2_9 0x034 0x24c 0x000 0x15 0x000 +#define MX25_PAD_A23__SIM2_TX1 0x034 0x24c 0x560 0x16 0x000 +#define MX25_PAD_A23__FEC_TDATA3 0x034 0x24c 0x000 0x17 0x000 #define MX25_PAD_A24__A24 0x038 0x250 0x000 0x10 0x000 #define MX25_PAD_A24__GPIO_2_10 0x038 0x250 0x000 0x15 0x000 +#define MX25_PAD_A24__SIM2_PD1 0x038 0x250 0x55c 0x16 0x000 #define MX25_PAD_A24__FEC_RX_CLK 0x038 0x250 0x514 0x17 0x000 #define MX25_PAD_A25__A25 0x03c 0x254 0x000 0x10 0x000 @@ -133,20 +154,25 @@ #define MX25_PAD_D15__D15 0x088 0x280 0x000 0x00 0x000 #define MX25_PAD_D15__LD16 0x088 0x280 0x000 0x01 0x000 #define MX25_PAD_D15__GPIO_4_5 0x088 0x280 0x000 0x05 0x000 +#define MX25_PAD_D15__SDHC1_DAT7 0x088 0x280 0x4d8 0x06 0x000 #define MX25_PAD_D14__D14 0x08c 0x284 0x000 0x00 0x000 #define MX25_PAD_D14__LD17 0x08c 0x284 0x000 0x01 0x000 #define MX25_PAD_D14__GPIO_4_6 0x08c 0x284 0x000 0x05 0x000 +#define MX25_PAD_D14__SDHC1_DAT6 0x08c 0x284 0x4d4 0x06 0x000 #define MX25_PAD_D13__D13 0x090 0x288 0x000 0x00 0x000 #define MX25_PAD_D13__LD18 0x090 0x288 0x000 0x01 0x000 #define MX25_PAD_D13__GPIO_4_7 0x090 0x288 0x000 0x05 0x000 +#define MX25_PAD_D13__SDHC1_DAT5 0x090 0x288 0x4d0 0x06 0x000 #define MX25_PAD_D12__D12 0x094 0x28c 0x000 0x00 0x000 #define MX25_PAD_D12__GPIO_4_8 0x094 0x28c 0x000 0x05 0x000 +#define MX25_PAD_D12__SDHC1_DAT4 0x094 0x28c 0x4cc 0x06 0x000 #define MX25_PAD_D11__D11 0x098 0x290 0x000 0x00 0x000 #define MX25_PAD_D11__GPIO_4_9 0x098 0x290 0x000 0x05 0x000 +#define MX25_PAD_D11__USBOTG_PWR 0x098 0x290 0x000 0x06 0x000 #define MX25_PAD_D10__D10 0x09c 0x294 0x000 0x00 0x000 #define MX25_PAD_D10__GPIO_4_10 0x09c 0x294 0x000 0x05 0x000 @@ -212,26 +238,33 @@ #define MX25_PAD_LD8__LD8 0x0e8 0x2e0 0x000 0x10 0x000 #define MX25_PAD_LD8__FEC_TX_ERR 0x0e8 0x2e0 0x000 0x15 0x000 +#define MX25_PAD_LD8__SDHC2_CMD 0x0e8 0x2e0 0x4e0 0x06 0x000 #define MX25_PAD_LD9__LD9 0x0ec 0x2e4 0x000 0x10 0x000 #define MX25_PAD_LD9__FEC_COL 0x0ec 0x2e4 0x504 0x15 0x001 +#define MX25_PAD_LD9__SDHC2_CLK 0x0ec 0x2e4 0x4dc 0x06 0x000 #define MX25_PAD_LD10__LD10 0x0f0 0x2e8 0x000 0x10 0x000 -#define MX25_PAD_LD10__FEC_RX_ER 0x0f0 0x2e8 0x518 0x15 0x001 +#define MX25_PAD_LD10__FEC_RX_ERR 0x0f0 0x2e8 0x518 0x15 0x001 #define MX25_PAD_LD11__LD11 0x0f4 0x2ec 0x000 0x10 0x000 #define MX25_PAD_LD11__FEC_RDATA2 0x0f4 0x2ec 0x50c 0x15 0x001 +#define MX25_PAD_LD11__SDHC2_DAT1 0x0f4 0x2ec 0x4e8 0x06 0x000 #define MX25_PAD_LD12__LD12 0x0f8 0x2f0 0x000 0x10 0x000 +#define MX25_PAD_LD12__CSPI2_MOSI 0x0f8 0x2f0 0x4a0 0x02 0x000 #define MX25_PAD_LD12__FEC_RDATA3 0x0f8 0x2f0 0x510 0x15 0x001 #define MX25_PAD_LD13__LD13 0x0fc 0x2f4 0x000 0x10 0x000 +#define MX25_PAD_LD13__CSPI2_MISO 0x0fc 0x2f4 0x49c 0x02 0x000 #define MX25_PAD_LD13__FEC_TDATA2 0x0fc 0x2f4 0x000 0x15 0x000 #define MX25_PAD_LD14__LD14 0x100 0x2f8 0x000 0x10 0x000 +#define MX25_PAD_LD14__CSPI2_SCLK 0x100 0x2f8 0x494 0x02 0x000 #define MX25_PAD_LD14__FEC_TDATA3 0x100 0x2f8 0x000 0x15 0x000 #define MX25_PAD_LD15__LD15 0x104 0x2fc 0x000 0x10 0x000 +#define MX25_PAD_LD15__CSPI2_RDY 0x104 0x2fc 0x498 0x02 0x000 #define MX25_PAD_LD15__FEC_RX_CLK 0x104 0x2fc 0x514 0x15 0x001 #define MX25_PAD_HSYNC__HSYNC 0x108 0x300 0x000 0x10 0x000 @@ -244,6 +277,7 @@ #define MX25_PAD_LSCLK__GPIO_1_24 0x110 0x308 0x000 0x15 0x000 #define MX25_PAD_OE_ACD__OE_ACD 0x114 0x30c 0x000 0x10 0x000 +#define MX25_PAD_OE_ACD__CSPI2_SS0 0x114 0x30c 0x4a4 0x02 0x000 #define MX25_PAD_OE_ACD__GPIO_1_25 0x114 0x30c 0x000 0x15 0x000 #define MX25_PAD_CONTRAST__CONTRAST 0x118 0x310 0x000 0x10 0x000 @@ -257,26 +291,31 @@ #define MX25_PAD_CSI_D2__CSI_D2 0x120 0x318 0x000 0x10 0x000 #define MX25_PAD_CSI_D2__UART5_RXD_MUX 0x120 0x318 0x578 0x11 0x001 +#define MX25_PAD_CSI_D2__SIM1_CLK0 0x120 0x318 0x000 0x04 0x000 #define MX25_PAD_CSI_D2__GPIO_1_27 0x120 0x318 0x000 0x15 0x000 #define MX25_PAD_CSI_D2__CSPI3_MOSI 0x120 0x318 0x000 0x17 0x000 #define MX25_PAD_CSI_D3__CSI_D3 0x124 0x31c 0x000 0x10 0x000 #define MX25_PAD_CSI_D3__UART5_TXD_MUX 0x124 0x31c 0x000 0x11 0x000 +#define MX25_PAD_CSI_D3__SIM1_RST0 0x124 0x31c 0x000 0x04 0x000 #define MX25_PAD_CSI_D3__GPIO_1_28 0x124 0x31c 0x000 0x15 0x000 #define MX25_PAD_CSI_D3__CSPI3_MISO 0x124 0x31c 0x4b4 0x17 0x001 #define MX25_PAD_CSI_D4__CSI_D4 0x128 0x320 0x000 0x10 0x000 #define MX25_PAD_CSI_D4__UART5_RTS 0x128 0x320 0x574 0x11 0x001 +#define MX25_PAD_CSI_D4__SIM1_VEN0 0x128 0x320 0x000 0x04 0x000 #define MX25_PAD_CSI_D4__GPIO_1_29 0x128 0x320 0x000 0x15 0x000 #define MX25_PAD_CSI_D4__CSPI3_SCLK 0x128 0x320 0x000 0x17 0x000 #define MX25_PAD_CSI_D5__CSI_D5 0x12c 0x324 0x000 0x10 0x000 -#define MX25_PAD_CSI_D5__UART5_CTS 0x12c 0x324 0x000 0x11 0x001 +#define MX25_PAD_CSI_D5__UART5_CTS 0x12c 0x324 0x000 0x11 0x000 +#define MX25_PAD_CSI_D5__SIM1_TX0 0x12c 0x324 0x000 0x04 0x000 #define MX25_PAD_CSI_D5__GPIO_1_30 0x12c 0x324 0x000 0x15 0x000 #define MX25_PAD_CSI_D5__CSPI3_RDY 0x12c 0x324 0x000 0x17 0x000 #define MX25_PAD_CSI_D6__CSI_D6 0x130 0x328 0x000 0x10 0x000 #define MX25_PAD_CSI_D6__SDHC2_CMD 0x130 0x328 0x4e0 0x12 0x001 +#define MX25_PAD_CSI_D6__SIM1_PD0 0x130 0x328 0x000 0x04 0x000 #define MX25_PAD_CSI_D6__GPIO_1_31 0x130 0x328 0x000 0x15 0x000 #define MX25_PAD_CSI_D7__CSI_D7 0x134 0x32c 0x000 0x10 0x000 @@ -284,32 +323,32 @@ #define MX25_PAD_CSI_D7__GPIO_1_6 0x134 0x32c 0x000 0x15 0x000 #define MX25_PAD_CSI_D8__CSI_D8 0x138 0x330 0x000 0x10 0x000 -#define MX25_PAD_CSI_D8__AUD6_RXC 0x138 0x330 0x000 0x12 0x001 +#define MX25_PAD_CSI_D8__AUD6_RXC 0x138 0x330 0x000 0x12 0x000 #define MX25_PAD_CSI_D8__GPIO_1_7 0x138 0x330 0x000 0x15 0x000 #define MX25_PAD_CSI_D8__CSPI3_SS2 0x138 0x330 0x4c4 0x17 0x000 #define MX25_PAD_CSI_D9__CSI_D9 0x13c 0x334 0x000 0x10 0x000 -#define MX25_PAD_CSI_D9__AUD6_RXFS 0x13c 0x334 0x000 0x12 0x001 +#define MX25_PAD_CSI_D9__AUD6_RXFS 0x13c 0x334 0x000 0x12 0x000 #define MX25_PAD_CSI_D9__GPIO_4_21 0x13c 0x334 0x000 0x15 0x000 #define MX25_PAD_CSI_D9__CSPI3_SS3 0x13c 0x334 0x4c8 0x17 0x000 #define MX25_PAD_CSI_MCLK__CSI_MCLK 0x140 0x338 0x000 0x10 0x000 -#define MX25_PAD_CSI_MCLK__AUD6_TXD 0x140 0x338 0x000 0x11 0x001 +#define MX25_PAD_CSI_MCLK__AUD6_TXD 0x140 0x338 0x000 0x11 0x000 #define MX25_PAD_CSI_MCLK__SDHC2_DAT0 0x140 0x338 0x4e4 0x12 0x001 #define MX25_PAD_CSI_MCLK__GPIO_1_8 0x140 0x338 0x000 0x15 0x000 #define MX25_PAD_CSI_VSYNC__CSI_VSYNC 0x144 0x33c 0x000 0x10 0x000 -#define MX25_PAD_CSI_VSYNC__AUD6_RXD 0x144 0x33c 0x000 0x11 0x001 +#define MX25_PAD_CSI_VSYNC__AUD6_RXD 0x144 0x33c 0x000 0x11 0x000 #define MX25_PAD_CSI_VSYNC__SDHC2_DAT1 0x144 0x33c 0x4e8 0x12 0x001 #define MX25_PAD_CSI_VSYNC__GPIO_1_9 0x144 0x33c 0x000 0x15 0x000 #define MX25_PAD_CSI_HSYNC__CSI_HSYNC 0x148 0x340 0x000 0x10 0x000 -#define MX25_PAD_CSI_HSYNC__AUD6_TXC 0x148 0x340 0x000 0x11 0x001 +#define MX25_PAD_CSI_HSYNC__AUD6_TXC 0x148 0x340 0x000 0x11 0x000 #define MX25_PAD_CSI_HSYNC__SDHC2_DAT2 0x148 0x340 0x4ec 0x12 0x001 #define MX25_PAD_CSI_HSYNC__GPIO_1_10 0x148 0x340 0x000 0x15 0x000 #define MX25_PAD_CSI_PIXCLK__CSI_PIXCLK 0x14c 0x344 0x000 0x10 0x000 -#define MX25_PAD_CSI_PIXCLK__AUD6_TXFS 0x14c 0x344 0x000 0x11 0x001 +#define MX25_PAD_CSI_PIXCLK__AUD6_TXFS 0x14c 0x344 0x000 0x11 0x000 #define MX25_PAD_CSI_PIXCLK__SDHC2_DAT3 0x14c 0x344 0x4f0 0x12 0x001 #define MX25_PAD_CSI_PIXCLK__GPIO_1_11 0x14c 0x344 0x000 0x15 0x000 @@ -369,8 +408,8 @@ #define MX25_PAD_UART2_RTS__CC1 0x188 0x380 0x000 0x13 0x000 #define MX25_PAD_UART2_RTS__GPIO_4_28 0x188 0x380 0x000 0x15 0x000 -#define MX25_PAD_UART2_CTS__FEC_RX_ER 0x18c 0x384 0x518 0x12 0x002 #define MX25_PAD_UART2_CTS__UART2_CTS 0x18c 0x384 0x000 0x10 0x000 +#define MX25_PAD_UART2_CTS__FEC_RX_ERR 0x18c 0x384 0x518 0x12 0x002 #define MX25_PAD_UART2_CTS__GPIO_4_29 0x18c 0x384 0x000 0x15 0x000 #define MX25_PAD_SD1_CMD__SD1_CMD 0x190 0x388 0x000 0x10 0x000 @@ -392,11 +431,11 @@ #define MX25_PAD_SD1_DATA1__GPIO_2_26 0x19c 0x394 0x000 0x15 0x000 #define MX25_PAD_SD1_DATA2__SD1_DATA2 0x1a0 0x398 0x000 0x10 0x000 -#define MX25_PAD_SD1_DATA2__FEC_RX_CLK 0x1a0 0x398 0x514 0x15 0x002 +#define MX25_PAD_SD1_DATA2__FEC_RX_CLK 0x1a0 0x398 0x514 0x12 0x002 #define MX25_PAD_SD1_DATA2__GPIO_2_27 0x1a0 0x398 0x000 0x15 0x000 #define MX25_PAD_SD1_DATA3__SD1_DATA3 0x1a4 0x39c 0x000 0x10 0x000 -#define MX25_PAD_SD1_DATA3__FEC_CRS 0x1a4 0x39c 0x508 0x10 0x002 +#define MX25_PAD_SD1_DATA3__FEC_CRS 0x1a4 0x39c 0x508 0x12 0x002 #define MX25_PAD_SD1_DATA3__GPIO_2_28 0x1a4 0x39c 0x000 0x15 0x000 #define MX25_PAD_KPP_ROW0__KPP_ROW0 0x1a8 0x3a0 0x000 0x10 0x000 @@ -410,7 +449,7 @@ #define MX25_PAD_KPP_ROW2__GPIO_2_31 0x1b0 0x3a8 0x000 0x15 0x000 #define MX25_PAD_KPP_ROW3__KPP_ROW3 0x1b4 0x3ac 0x000 0x10 0x000 -#define MX25_PAD_KPP_ROW3__CSI_LD1 0x1b4 0x3ac 0x48c 0x13 0x002 +#define MX25_PAD_KPP_ROW3__CSI_D1 0x1b4 0x3ac 0x48c 0x13 0x002 #define MX25_PAD_KPP_ROW3__GPIO_3_0 0x1b4 0x3ac 0x000 0x15 0x000 #define MX25_PAD_KPP_COL0__KPP_COL0 0x1b8 0x3b0 0x000 0x10 0x000 @@ -455,9 +494,18 @@ #define MX25_PAD_FEC_RDATA0__GPIO_3_10 0x1dc 0x3d4 0x000 0x15 0x000 #define MX25_PAD_FEC_RDATA1__FEC_RDATA1 0x1e0 0x3d8 0x000 0x10 0x000 +/* + * According to the i.MX25 Reference manual (IMX25RM, Rev. 2, + * 01/2011) this is CAN1_TX but that's wrong. + */ +#define MX25_PAD_FEC_RDATA1__CAN2_TX 0x1e0 0x3d8 0x000 0x14 0x000 #define MX25_PAD_FEC_RDATA1__GPIO_3_11 0x1e0 0x3d8 0x000 0x15 0x000 #define MX25_PAD_FEC_RX_DV__FEC_RX_DV 0x1e4 0x3dc 0x000 0x10 0x000 +/* + * According to the i.MX25 Reference manual (IMX25RM, Rev. 2, + * 01/2011) this is CAN1_RX but that's wrong. + */ #define MX25_PAD_FEC_RX_DV__CAN2_RX 0x1e4 0x3dc 0x484 0x14 0x000 #define MX25_PAD_FEC_RX_DV__GPIO_3_12 0x1e4 0x3dc 0x000 0x15 0x000 @@ -471,30 +519,34 @@ #define MX25_PAD_DE_B__DE_B 0x1f0 0x3ec 0x000 0x10 0x000 #define MX25_PAD_DE_B__GPIO_2_20 0x1f0 0x3ec 0x000 0x15 0x000 -#define MX25_PAD_TDO__TDO 0x000 0x3e8 0x000 0x00 0x000 - #define MX25_PAD_GPIO_A__GPIO_A 0x1f4 0x3f0 0x000 0x10 0x000 #define MX25_PAD_GPIO_A__CAN1_TX 0x1f4 0x3f0 0x000 0x16 0x000 #define MX25_PAD_GPIO_A__USBOTG_PWR 0x1f4 0x3f0 0x000 0x12 0x000 #define MX25_PAD_GPIO_B__GPIO_B 0x1f8 0x3f4 0x000 0x10 0x000 -#define MX25_PAD_GPIO_B__CAN1_RX 0x1f8 0x3f4 0x480 0x16 0x001 #define MX25_PAD_GPIO_B__USBOTG_OC 0x1f8 0x3f4 0x57c 0x12 0x001 +#define MX25_PAD_GPIO_B__CAN1_RX 0x1f8 0x3f4 0x480 0x16 0x001 #define MX25_PAD_GPIO_C__GPIO_C 0x1fc 0x3f8 0x000 0x10 0x000 +#define MX25_PAD_GPIO_C__PWM4_PWMO 0x1fc 0x3f8 0x000 0x11 0x000 +#define MX25_PAD_GPIO_C__I2C2_SCL 0x1fc 0x3f8 0x51c 0x12 0x001 +#define MX25_PAD_GPIO_C__KPP_COL4 0x1fc 0x3f8 0x52c 0x13 0x001 #define MX25_PAD_GPIO_C__CAN2_TX 0x1fc 0x3f8 0x000 0x16 0x000 #define MX25_PAD_GPIO_D__GPIO_D 0x200 0x3fc 0x000 0x10 0x000 +#define MX25_PAD_GPIO_D__I2C2_SDA 0x200 0x3fc 0x520 0x12 0x001 #define MX25_PAD_GPIO_D__CAN2_RX 0x200 0x3fc 0x484 0x16 0x001 #define MX25_PAD_GPIO_E__GPIO_E 0x204 0x400 0x000 0x10 0x000 #define MX25_PAD_GPIO_E__I2C3_CLK 0x204 0x400 0x524 0x11 0x002 #define MX25_PAD_GPIO_E__LD16 0x204 0x400 0x000 0x12 0x000 #define MX25_PAD_GPIO_E__AUD7_TXD 0x204 0x400 0x000 0x14 0x000 +#define MX25_PAD_GPIO_E__UART4_RXD 0x204 0x400 0x570 0x16 0x002 #define MX25_PAD_GPIO_F__GPIO_F 0x208 0x404 0x000 0x10 0x000 #define MX25_PAD_GPIO_F__LD17 0x208 0x404 0x000 0x12 0x000 #define MX25_PAD_GPIO_F__AUD7_TXC 0x208 0x404 0x000 0x14 0x000 +#define MX25_PAD_GPIO_F__UART4_TXD 0x208 0x404 0x000 0x16 0x000 #define MX25_PAD_EXT_ARMCLK__EXT_ARMCLK 0x20c 0x000 0x000 0x10 0x000 #define MX25_PAD_EXT_ARMCLK__GPIO_3_15 0x20c 0x000 0x000 0x15 0x000 @@ -505,6 +557,7 @@ #define MX25_PAD_VSTBY_REQ__VSTBY_REQ 0x214 0x408 0x000 0x10 0x000 #define MX25_PAD_VSTBY_REQ__AUD7_TXFS 0x214 0x408 0x000 0x14 0x000 #define MX25_PAD_VSTBY_REQ__GPIO_3_17 0x214 0x408 0x000 0x15 0x000 + #define MX25_PAD_VSTBY_ACK__VSTBY_ACK 0x218 0x40c 0x000 0x10 0x000 #define MX25_PAD_VSTBY_ACK__GPIO_3_18 0x218 0x40c 0x000 0x15 0x000 @@ -517,6 +570,7 @@ #define MX25_PAD_BOOT_MODE0__BOOT_MODE0 0x224 0x000 0x000 0x00 0x000 #define MX25_PAD_BOOT_MODE0__GPIO_4_30 0x224 0x000 0x000 0x05 0x000 + #define MX25_PAD_BOOT_MODE1__BOOT_MODE1 0x228 0x000 0x000 0x00 0x000 #define MX25_PAD_BOOT_MODE1__GPIO_4_31 0x228 0x000 0x000 0x05 0x000 diff --git a/arch/arm/boot/dts/imx25.dtsi b/arch/arm/boot/dts/imx25.dtsi index e4d3aecc4ed2..677f81d9dcd5 100644 --- a/arch/arm/boot/dts/imx25.dtsi +++ b/arch/arm/boot/dts/imx25.dtsi @@ -428,6 +428,7 @@ pwm4: pwm@53fc8000 { compatible = "fsl,imx25-pwm", "fsl,imx27-pwm"; + #pwm-cells = <2>; reg = <0x53fc8000 0x4000>; clocks = <&clks 108>, <&clks 52>; clock-names = "ipg", "per"; diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi index 4b063b68db44..6951b66d1ab7 100644 --- a/arch/arm/boot/dts/imx27.dtsi +++ b/arch/arm/boot/dts/imx27.dtsi @@ -488,6 +488,7 @@ interrupts = <54>; clocks = <&clks IMX27_CLK_USB_IPG_GATE>; fsl,usbmisc = <&usbmisc 1>; + dr_mode = "host"; status = "disabled"; }; @@ -497,6 +498,7 @@ interrupts = <55>; clocks = <&clks IMX27_CLK_USB_IPG_GATE>; fsl,usbmisc = <&usbmisc 2>; + dr_mode = "host"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx28-apf28.dts b/arch/arm/boot/dts/imx28-apf28.dts index 7198fe3798c6..070e59cbdd8b 100644 --- a/arch/arm/boot/dts/imx28-apf28.dts +++ b/arch/arm/boot/dts/imx28-apf28.dts @@ -78,7 +78,7 @@ phy-mode = "rmii"; pinctrl-names = "default"; pinctrl-0 = <&mac0_pins_a>; - phy-reset-gpios = <&gpio4 13 0>; + phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts index 1f38a052ad4b..7ac4f1af16ac 100644 --- a/arch/arm/boot/dts/imx28-apf28dev.dts +++ b/arch/arm/boot/dts/imx28-apf28dev.dts @@ -110,6 +110,13 @@ }; }; }; + + can0: can@80032000 { + pinctrl-names = "default"; + pinctrl-0 = <&can0_pins_a>; + xceiver-supply = <®_can0_vcc>; + status = "okay"; + }; }; apbx@80040000 { @@ -130,6 +137,13 @@ status = "okay"; }; + auart0: serial@8006a000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart0_pins_a>; + fsl,uart-has-rtscts; + status = "okay"; + }; + usbphy0: usbphy@8007c000 { status = "okay"; }; @@ -143,7 +157,8 @@ ahb@80080000 { usb0: usb@80080000 { pinctrl-names = "default"; - pinctrl-0 = <&usb0_otg_apf28dev>; + pinctrl-0 = <&usb0_otg_apf28dev + &usb0_id_pins_b>; vbus-supply = <®_usb0_vbus>; status = "okay"; }; @@ -156,7 +171,7 @@ phy-mode = "rmii"; pinctrl-names = "default"; pinctrl-0 = <&mac1_pins_a>; - phy-reset-gpios = <&gpio0 23 0>; + phy-reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; status = "okay"; }; }; @@ -175,6 +190,14 @@ gpio = <&gpio1 23 1>; enable-active-high; }; + + reg_can0_vcc: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "can0_vcc"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; }; leds { @@ -200,8 +223,9 @@ user-button { label = "User button"; - gpios = <&gpio0 17 0>; + gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; linux,code = <0x100>; + gpio-key,wakeup; }; }; }; diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index 47f68ac868d4..4e073e854742 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -829,6 +829,19 @@ fsl,pull-up = ; }; + spi3_pins_b: spi3@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_SSP3_SCK__SSP3_SCK + MX28_PAD_SSP3_MOSI__SSP3_CMD + MX28_PAD_SSP3_MISO__SSP3_D0 + MX28_PAD_SSP3_SS0__SSP3_D3 + >; + fsl,drive-strength = ; + fsl,voltage = ; + fsl,pull-up = ; + }; + usb0_pins_a: usb0@0 { reg = <0>; fsl,pinmux-ids = < @@ -900,7 +913,7 @@ 80 81 68 69 70 71 72 73 74 75 76 77>; - interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty", + interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty", "saif0", "saif1", "i2c0", "i2c1", "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx", "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx"; @@ -1197,6 +1210,7 @@ interrupts = <92>; clocks = <&clks 61>; fsl,usbphy = <&usbphy1>; + dr_mode = "host"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx35.dtsi b/arch/arm/boot/dts/imx35.dtsi index 6932928f3b45..b6478e97d6a7 100644 --- a/arch/arm/boot/dts/imx35.dtsi +++ b/arch/arm/boot/dts/imx35.dtsi @@ -318,6 +318,7 @@ clocks = <&clks 73>; fsl,usbmisc = <&usbmisc 1>; fsl,usbphy = <&usbphy1>; + dr_mode = "host"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx50.dtsi b/arch/arm/boot/dts/imx50.dtsi index 620b0f030591..e2457138311f 100644 --- a/arch/arm/boot/dts/imx50.dtsi +++ b/arch/arm/boot/dts/imx50.dtsi @@ -197,6 +197,7 @@ reg = <0x53f80200 0x0200>; interrupts = <14>; clocks = <&clks IMX5_CLK_USB_PHY2_GATE>; + dr_mode = "host"; status = "disabled"; }; @@ -205,6 +206,7 @@ reg = <0x53f80400 0x0200>; interrupts = <16>; clocks = <&clks IMX5_CLK_USBOH3_GATE>; + dr_mode = "host"; status = "disabled"; }; @@ -213,6 +215,7 @@ reg = <0x53f80600 0x0200>; interrupts = <17>; clocks = <&clks IMX5_CLK_USBOH3_GATE>; + dr_mode = "host"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx51.dtsi b/arch/arm/boot/dts/imx51.dtsi index c0116cffc513..f46fe9bf0bcb 100644 --- a/arch/arm/boot/dts/imx51.dtsi +++ b/arch/arm/boot/dts/imx51.dtsi @@ -265,6 +265,7 @@ interrupts = <14>; clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 1>; + dr_mode = "host"; status = "disabled"; }; @@ -274,6 +275,7 @@ interrupts = <16>; clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 2>; + dr_mode = "host"; status = "disabled"; }; @@ -283,6 +285,7 @@ interrupts = <17>; clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 3>; + dr_mode = "host"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi index ff4fa7ecacd8..c3e3ca9362fb 100644 --- a/arch/arm/boot/dts/imx53.dtsi +++ b/arch/arm/boot/dts/imx53.dtsi @@ -309,6 +309,7 @@ clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 1>; fsl,usbphy = <&usbphy1>; + dr_mode = "host"; status = "disabled"; }; @@ -318,6 +319,7 @@ interrupts = <16>; clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 2>; + dr_mode = "host"; status = "disabled"; }; @@ -327,6 +329,7 @@ interrupts = <17>; clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 3>; + dr_mode = "host"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx6dl-aristainetos_4.dts b/arch/arm/boot/dts/imx6dl-aristainetos_4.dts index 9cd06e5e59f0..d4c4a22db488 100644 --- a/arch/arm/boot/dts/imx6dl-aristainetos_4.dts +++ b/arch/arm/boot/dts/imx6dl-aristainetos_4.dts @@ -83,3 +83,7 @@ &ipu1_di0_disp0 { remote-endpoint = <&display0_in>; }; + +&pwm1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6dl-aristainetos_7.dts b/arch/arm/boot/dts/imx6dl-aristainetos_7.dts index b413e24288dc..15203f0e9725 100644 --- a/arch/arm/boot/dts/imx6dl-aristainetos_7.dts +++ b/arch/arm/boot/dts/imx6dl-aristainetos_7.dts @@ -72,3 +72,7 @@ &ipu1_di0_disp0 { remote-endpoint = <&display0_in>; }; + +&pwm3 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6dl-cubox-i.dts b/arch/arm/boot/dts/imx6dl-cubox-i.dts index 58aa8f2b0f26..e0b7fe8e18f8 100644 --- a/arch/arm/boot/dts/imx6dl-cubox-i.dts +++ b/arch/arm/boot/dts/imx6dl-cubox-i.dts @@ -1,5 +1,43 @@ /* * Copyright (C) 2014 Russell King + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/imx6dl-hummingboard.dts b/arch/arm/boot/dts/imx6dl-hummingboard.dts index 44a0e6736bb1..7369d2d7da3e 100644 --- a/arch/arm/boot/dts/imx6dl-hummingboard.dts +++ b/arch/arm/boot/dts/imx6dl-hummingboard.dts @@ -1,6 +1,44 @@ /* * Copyright (C) 2014 Rabeeh Khoury (rabeeh@solid-run.com) * Based on dt work by Russell King + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/imx6q-cubox-i.dts b/arch/arm/boot/dts/imx6q-cubox-i.dts index 9efd8b0c8011..670bd8c4c847 100644 --- a/arch/arm/boot/dts/imx6q-cubox-i.dts +++ b/arch/arm/boot/dts/imx6q-cubox-i.dts @@ -1,5 +1,43 @@ /* * Copyright (C) 2014 Russell King + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/imx6q-hummingboard.dts b/arch/arm/boot/dts/imx6q-hummingboard.dts index c2bf8476ce45..0f6044553a24 100644 --- a/arch/arm/boot/dts/imx6q-hummingboard.dts +++ b/arch/arm/boot/dts/imx6q-hummingboard.dts @@ -1,6 +1,44 @@ /* * Copyright (C) 2014 Rabeeh Khoury (rabeeh@solid-run.com) * Based on dt work by Russell King + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ /dts-v1/; diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi index 93ec79bb6b35..399103b8e2c9 100644 --- a/arch/arm/boot/dts/imx6q.dtsi +++ b/arch/arm/boot/dts/imx6q.dtsi @@ -294,19 +294,21 @@ }; &mipi_dsi { - port@2 { - reg = <2>; + ports { + port@2 { + reg = <2>; - mipi_mux_2: endpoint { - remote-endpoint = <&ipu2_di0_mipi>; + mipi_mux_2: endpoint { + remote-endpoint = <&ipu2_di0_mipi>; + }; }; - }; - port@3 { - reg = <3>; + port@3 { + reg = <3>; - mipi_mux_3: endpoint { - remote-endpoint = <&ipu2_di1_mipi>; + mipi_mux_3: endpoint { + remote-endpoint = <&ipu2_di1_mipi>; + }; }; }; }; diff --git a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi b/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi index 6a524ca011e7..d033bb182060 100644 --- a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi +++ b/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi @@ -1,8 +1,48 @@ /* * Copyright (C) 2014 Russell King + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ #include "imx6qdl-microsom.dtsi" #include "imx6qdl-microsom-ar8035.dtsi" +#include +#include / { ir_recv: ir-receiver { @@ -66,6 +106,18 @@ spdif-controller = <&spdif>; spdif-out; }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-0 = <&pinctrl_gpio_key>; + pinctrl-names = "default"; + + button_0 { + label = "Button 0"; + gpios = <&gpio3 8 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; }; &hdmi { @@ -170,9 +222,19 @@ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059 >; }; + + pinctrl_gpio_key: gpio-key { + fsl,pins = < + MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x17059 + >; + }; }; }; +&pwm1 { + status = "okay"; +}; + &spdif { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_cubox_i_spdif>; diff --git a/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi b/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi index 62841e85a91e..151a3db2aea9 100644 --- a/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi +++ b/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi @@ -1,5 +1,43 @@ /* * Copyright (C) 2013,2014 Russell King + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ #include "imx6qdl-microsom.dtsi" #include "imx6qdl-microsom-ar8035.dtsi" @@ -50,6 +88,19 @@ }; }; + sound-sgtl5000 { + audio-codec = <&sgtl5000>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + compatible = "fsl,imx-audio-sgtl5000"; + model = "On-board Codec"; + mux-ext-port = <5>; + mux-int-port = <1>; + ssi-controller = <&ssi1>; + }; + sound-spdif { compatible = "fsl,imx-audio-spdif"; model = "On-board SPDIF"; @@ -59,6 +110,10 @@ }; }; +&audmux { + status = "okay"; +}; + &can1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hummingboard_flexcan1>; @@ -75,16 +130,24 @@ &i2c1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hummingboard_i2c1>; - - /* - * Not fitted on Carrier-1 board... yet status = "okay"; + /* Pro baseboard model */ rtc: pcf8523@68 { compatible = "nxp,pcf8523"; reg = <0x68>; }; - */ + + /* Pro baseboard model */ + sgtl5000: sgtl5000@0a { + clocks = <&clks IMX6QDL_CLK_CKO>; + compatible = "fsl,sgtl5000"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hummingboard_sgtl5000>; + reg = <0x0a>; + VDDA-supply = <®_3p3v>; + VDDIO-supply = <®_3p3v>; + }; }; &i2c2 { @@ -129,6 +192,20 @@ >; }; + pinctrl_hummingboard_pwm1: pwm1grp { + fsl,pins = ; + }; + + pinctrl_hummingboard_sgtl5000: hummingboard-sgtl5000 { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0 + MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0 + MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x110b0 + MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x130b0 + MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x130b0 + >; + }; + pinctrl_hummingboard_spdif: hummingboard-spdif { fsl,pins = ; }; @@ -168,12 +245,28 @@ }; }; +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hummingboard_pwm1>; + status = "okay"; +}; + +&pwm2 { + pinctrl-names = "default"; + status = "okay"; +}; + &spdif { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hummingboard_spdif>; status = "okay"; }; +&ssi1 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + &usbh1 { disable-over-current; vbus-supply = <®_usbh1_vbus>; diff --git a/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi b/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi index db9f45b2c573..4a1820309cdb 100644 --- a/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi +++ b/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi @@ -3,6 +3,44 @@ * * This describes the hookup for an AR8035 to the iMX6 on the SolidRun * MicroSOM. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ &fec { pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/imx6qdl-microsom.dtsi b/arch/arm/boot/dts/imx6qdl-microsom.dtsi index 79eac6849d4c..349f82be816e 100644 --- a/arch/arm/boot/dts/imx6qdl-microsom.dtsi +++ b/arch/arm/boot/dts/imx6qdl-microsom.dtsi @@ -1,5 +1,43 @@ /* * Copyright (C) 2013,2014 Russell King + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */ &iomuxc { diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi index 19cc269a08d4..1ce6133b67f5 100644 --- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi +++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi @@ -31,6 +31,7 @@ regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; gpio = <&gpio4 15 0>; + enable-active-high; }; reg_usb_h1_vbus: regulator@1 { @@ -40,6 +41,7 @@ regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; gpio = <&gpio1 0 0>; + enable-active-high; }; }; diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi index 009abd69385d..3b24b12651b2 100644 --- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi @@ -182,6 +182,33 @@ }; }; +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + max7310_a: gpio@30 { + compatible = "maxim,max7310"; + reg = <0x30>; + gpio-controller; + #gpio-cells = <2>; + }; + + max7310_b: gpio@32 { + compatible = "maxim,max7310"; + reg = <0x32>; + gpio-controller; + #gpio-cells = <2>; + }; + + max7310_c: gpio@34 { + compatible = "maxim,max7310"; + reg = <0x34>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + &iomuxc { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; @@ -265,6 +292,13 @@ >; }; + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 + >; + }; + pinctrl_pwm3: pwm1grp { fsl,pins = < MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1 diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index d6c69ec44314..f74a8ded515f 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -53,6 +53,7 @@ interrupt-controller; reg = <0x00a01000 0x1000>, <0x00a00100 0x100>; + interrupt-parent = <&intc>; }; clocks { @@ -82,7 +83,7 @@ #address-cells = <1>; #size-cells = <1>; compatible = "simple-bus"; - interrupt-parent = <&intc>; + interrupt-parent = <&gpc>; ranges; dma_apbh: dma-apbh@00110000 { @@ -122,6 +123,7 @@ compatible = "arm,cortex-a9-twd-timer"; reg = <0x00a00600 0x20>; interrupts = <1 13 0xf01>; + interrupt-parent = <&intc>; clocks = <&clks IMX6QDL_CLK_TWD>; }; @@ -357,6 +359,7 @@ clocks = <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_PWM1>; clock-names = "ipg", "per"; + status = "disabled"; }; pwm2: pwm@02084000 { @@ -367,6 +370,7 @@ clocks = <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_PWM2>; clock-names = "ipg", "per"; + status = "disabled"; }; pwm3: pwm@02088000 { @@ -377,6 +381,7 @@ clocks = <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_PWM3>; clock-names = "ipg", "per"; + status = "disabled"; }; pwm4: pwm@0208c000 { @@ -387,6 +392,7 @@ clocks = <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_PWM4>; clock-names = "ipg", "per"; + status = "disabled"; }; can1: flexcan@02090000 { @@ -598,7 +604,7 @@ regulator-name = "vddpu"; regulator-min-microvolt = <725000>; regulator-max-microvolt = <1450000>; - regulator-always-on; + regulator-enable-ramp-delay = <150>; anatop-reg-offset = <0x140>; anatop-vol-bit-shift = <9>; anatop-vol-bit-width = <5>; @@ -658,7 +664,7 @@ #size-cells = <1>; ranges = <0 0x020cc000 0x4000>; - snvs-rtc-lp@34 { + snvs_rtc: snvs-rtc-lp@34 { compatible = "fsl,sec-v4.0-mon-rtc-lp"; reg = <0x34 0x58>; interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>, @@ -693,8 +699,19 @@ gpc: gpc@020dc000 { compatible = "fsl,imx6q-gpc"; reg = <0x020dc000 0x4000>; + interrupt-controller; + #interrupt-cells = <3>; interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>, <0 90 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&intc>; + pu-supply = <®_pu>; + clocks = <&clks IMX6QDL_CLK_GPU3D_CORE>, + <&clks IMX6QDL_CLK_GPU3D_SHADER>, + <&clks IMX6QDL_CLK_GPU2D_CORE>, + <&clks IMX6QDL_CLK_GPU2D_AXI>, + <&clks IMX6QDL_CLK_OPENVG_AXI>, + <&clks IMX6QDL_CLK_VPU_AXI>; + #power-domain-cells = <1>; }; gpr: iomuxc-gpr@020e0000 { @@ -845,6 +862,7 @@ clocks = <&clks IMX6QDL_CLK_USBOH3>; fsl,usbphy = <&usbphy2>; fsl,usbmisc = <&usbmisc 1>; + dr_mode = "host"; status = "disabled"; }; @@ -854,6 +872,7 @@ interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; fsl,usbmisc = <&usbmisc 2>; + dr_mode = "host"; status = "disabled"; }; @@ -863,6 +882,7 @@ interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6QDL_CLK_USBOH3>; fsl,usbmisc = <&usbmisc 3>; + dr_mode = "host"; status = "disabled"; }; @@ -1022,19 +1042,24 @@ reg = <0x021e0000 0x4000>; status = "disabled"; - port@0 { - reg = <0>; + ports { + #address-cells = <1>; + #size-cells = <0>; - mipi_mux_0: endpoint { - remote-endpoint = <&ipu1_di0_mipi>; + port@0 { + reg = <0>; + + mipi_mux_0: endpoint { + remote-endpoint = <&ipu1_di0_mipi>; + }; }; - }; - port@1 { - reg = <1>; + port@1 { + reg = <1>; - mipi_mux_1: endpoint { - remote-endpoint = <&ipu1_di1_mipi>; + mipi_mux_1: endpoint { + remote-endpoint = <&ipu1_di1_mipi>; + }; }; }; }; diff --git a/arch/arm/boot/dts/imx6sl-warp.dts b/arch/arm/boot/dts/imx6sl-warp.dts new file mode 100644 index 000000000000..64f7decf1fdc --- /dev/null +++ b/arch/arm/boot/dts/imx6sl-warp.dts @@ -0,0 +1,262 @@ +/* + * Copyright 2014, 2015 O.S. Systems Software LTDA. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this file; if not, write to the Free + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include +#include "imx6sl.dtsi" + +/ { + model = "WaRP Board"; + compatible = "warp,imx6sl-warp", "fsl,imx6sl"; + + memory { + reg = <0x80000000 0x20000000>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_usb_otg1_vbus: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "usb_otg1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio4 0 0>; + enable-active-high; + }; + + reg_usb_otg2_vbus: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "usb_otg2_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio4 2 0>; + enable-active-high; + }; + + reg_1p8v: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "1P8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + + usdhc3_pwrseq: usdhc3_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>, /* WL_REG_ON */ + <&gpio3 25 GPIO_ACTIVE_LOW>, /* BT_REG_ON */ + <&gpio4 4 GPIO_ACTIVE_LOW>, /* BT_WAKE */ + <&gpio4 6 GPIO_ACTIVE_LOW>; /* BT_RST_N */ + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&usbotg1 { + vbus-supply = <®_usb_otg1_vbus>; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usbotg2 { + vbus-supply = <®_usb_otg2_vbus>; + disable-over-current; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <4>; + non-removable; + keep-power-in-suspend; + enable-sdio-wakeup; + mmc-pwrseq = <&usdhc3_pwrseq>; + status = "okay"; +}; + +&iomuxc { + imx6sl-warp { + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x41b0b1 + MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x41b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6SL_PAD_EPDC_D12__UART2_RX_DATA 0x41b0b1 + MX6SL_PAD_EPDC_D13__UART2_TX_DATA 0x41b0b1 + MX6SL_PAD_EPDC_D14__UART2_RTS_B 0x4130B1 + MX6SL_PAD_EPDC_D15__UART2_CTS_B 0x4130B1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6SL_PAD_AUD_RXC__UART3_RX_DATA 0x41b0b1 + MX6SL_PAD_AUD_RXC__UART3_TX_DATA 0x41b0b1 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6SL_PAD_SD2_CMD__SD2_CMD 0x417059 + MX6SL_PAD_SD2_CLK__SD2_CLK 0x410059 + MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x417059 + MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x417059 + MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x417059 + MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x417059 + MX6SL_PAD_SD2_DAT4__SD2_DATA4 0x417059 + MX6SL_PAD_SD2_DAT5__SD2_DATA5 0x417059 + MX6SL_PAD_SD2_DAT6__SD2_DATA6 0x417059 + MX6SL_PAD_SD2_DAT7__SD2_DATA7 0x417059 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + MX6SL_PAD_SD2_CMD__SD2_CMD 0x4170b9 + MX6SL_PAD_SD2_CLK__SD2_CLK 0x4100b9 + MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x4170b9 + MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x4170b9 + MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x4170b9 + MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x4170b9 + MX6SL_PAD_SD2_DAT4__SD2_DATA4 0x4170b9 + MX6SL_PAD_SD2_DAT5__SD2_DATA5 0x4170b9 + MX6SL_PAD_SD2_DAT6__SD2_DATA6 0x4170b9 + MX6SL_PAD_SD2_DAT7__SD2_DATA7 0x4170b9 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + MX6SL_PAD_SD2_CMD__SD2_CMD 0x4170f9 + MX6SL_PAD_SD2_CLK__SD2_CLK 0x4100f9 + MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x4170f9 + MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x4170f9 + MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x4170f9 + MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x4170f9 + MX6SL_PAD_SD2_DAT4__SD2_DATA4 0x4170f9 + MX6SL_PAD_SD2_DAT5__SD2_DATA5 0x4170f9 + MX6SL_PAD_SD2_DAT6__SD2_DATA6 0x4170f9 + MX6SL_PAD_SD2_DAT7__SD2_DATA7 0x4170f9 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6SL_PAD_SD3_CMD__SD3_CMD 0x417059 + MX6SL_PAD_SD3_CLK__SD3_CLK 0x410059 + MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x417059 + MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x417059 + MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x417059 + MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x417059 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3grp100mhz { + fsl,pins = < + MX6SL_PAD_SD3_CMD__SD3_CMD 0x4170b9 + MX6SL_PAD_SD3_CLK__SD3_CLK 0x4100b9 + MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x4170b9 + MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x4170b9 + MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x4170b9 + MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x4170b9 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3grp200mhz { + fsl,pins = < + MX6SL_PAD_SD3_CMD__SD3_CMD 0x4170f9 + MX6SL_PAD_SD3_CLK__SD3_CLK 0x4100f9 + MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x4170f9 + MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x4170f9 + MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x4170f9 + MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x4170f9 + >; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi index 36ab8e054cee..a78e715e3982 100644 --- a/arch/arm/boot/dts/imx6sl.dtsi +++ b/arch/arm/boot/dts/imx6sl.dtsi @@ -72,6 +72,7 @@ interrupt-controller; reg = <0x00a01000 0x1000>, <0x00a00100 0x100>; + interrupt-parent = <&intc>; }; clocks { @@ -95,7 +96,7 @@ #address-cells = <1>; #size-cells = <1>; compatible = "simple-bus"; - interrupt-parent = <&intc>; + interrupt-parent = <&gpc>; ranges; ocram: sram@00900000 { @@ -568,7 +569,7 @@ #size-cells = <1>; ranges = <0 0x020cc000 0x4000>; - snvs-rtc-lp@34 { + snvs_rtc: snvs-rtc-lp@34 { compatible = "fsl,sec-v4.0-mon-rtc-lp"; reg = <0x34 0x58>; interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>, @@ -603,7 +604,14 @@ gpc: gpc@020dc000 { compatible = "fsl,imx6sl-gpc", "fsl,imx6q-gpc"; reg = <0x020dc000 0x4000>; + interrupt-controller; + #interrupt-cells = <3>; interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&intc>; + pu-supply = <®_pu>; + clocks = <&clks IMX6SL_CLK_GPU2D_OVG>, + <&clks IMX6SL_CLK_GPU2D_PODF>; + #power-domain-cells = <1>; }; gpr: iomuxc-gpr@020e0000 { @@ -699,6 +707,7 @@ interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_USBOH3>; fsl,usbmisc = <&usbmisc 2>; + dr_mode = "host"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx6sx-sdb-reva.dts b/arch/arm/boot/dts/imx6sx-sdb-reva.dts new file mode 100644 index 000000000000..c76b87cba275 --- /dev/null +++ b/arch/arm/boot/dts/imx6sx-sdb-reva.dts @@ -0,0 +1,143 @@ +/* + * Copyright (C) 2015 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "imx6sx-sdb.dtsi" + +/ { + model = "Freescale i.MX6 SoloX SDB RevA Board"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic: pfuze100@08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + regulator-always-on; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; +}; + +&qspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi2>; + status = "okay"; + + flash0: s25fl128s@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,s25fl128s"; + spi-max-frequency = <66000000>; + }; + + flash1: s25fl128s@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,s25fl128s"; + spi-max-frequency = <66000000>; + }; +}; diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-sdb.dts index 32f07d6b4042..0bfc4e7865b2 100644 --- a/arch/arm/boot/dts/imx6sx-sdb.dts +++ b/arch/arm/boot/dts/imx6sx-sdb.dts @@ -1,197 +1,40 @@ /* - * Copyright (C) 2014 Freescale Semiconductor, Inc. + * Copyright (C) 2015 Freescale Semiconductor, Inc. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -/dts-v1/; - -#include -#include -#include "imx6sx.dtsi" +#include "imx6sx-sdb.dtsi" / { - model = "Freescale i.MX6 SoloX SDB Board"; - compatible = "fsl,imx6sx-sdb", "fsl,imx6sx"; - - chosen { - stdout-path = &uart1; - }; - - memory { - reg = <0x80000000 0x40000000>; - }; - - backlight { - compatible = "pwm-backlight"; - pwms = <&pwm3 0 5000000>; - brightness-levels = <0 4 8 16 32 64 128 255>; - default-brightness-level = <6>; - }; - - gpio-keys { - compatible = "gpio-keys"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gpio_keys>; - - volume-up { - label = "Volume Up"; - gpios = <&gpio1 18 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - volume-down { - label = "Volume Down"; - gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - - vcc_sd3: regulator@0 { - compatible = "regulator-fixed"; - reg = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_vcc_sd3>; - regulator-name = "VCC_SD3"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - reg_usb_otg1_vbus: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usb_otg1>; - regulator-name = "usb_otg1_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - reg_usb_otg2_vbus: regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usb_otg2>; - regulator-name = "usb_otg2_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - reg_psu_5v: regulator@3 { - compatible = "regulator-fixed"; - reg = <3>; - regulator-name = "PSU-5V0"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - }; - - reg_lcd_3v3: regulator@4 { - compatible = "regulator-fixed"; - reg = <4>; - regulator-name = "lcd-3v3"; - gpio = <&gpio3 27 0>; - enable-active-high; - }; - - reg_peri_3v3: regulator@5 { - compatible = "regulator-fixed"; - reg = <5>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_peri_3v3>; - regulator-name = "peri_3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>; - enable-active-high; - regulator-always-on; - }; - - reg_enet_3v3: regulator@6 { - compatible = "regulator-fixed"; - reg = <6>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_enet_3v3>; - regulator-name = "enet_3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; - }; - }; - - sound { - compatible = "fsl,imx6sx-sdb-wm8962", "fsl,imx-audio-wm8962"; - model = "wm8962-audio"; - ssi-controller = <&ssi2>; - audio-codec = <&codec>; - audio-routing = - "Headphone Jack", "HPOUTL", - "Headphone Jack", "HPOUTR", - "Ext Spk", "SPKOUTL", - "Ext Spk", "SPKOUTR", - "AMIC", "MICBIAS", - "IN3R", "AMIC"; - mux-int-port = <2>; - mux-ext-port = <6>; - }; + model = "Freescale i.MX6 SoloX SDB RevB Board"; }; -&audmux { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_audmux>; - status = "okay"; -}; - -&fec1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_enet1>; - phy-supply = <®_enet_3v3>; - phy-mode = "rgmii"; - phy-handle = <ðphy1>; - status = "okay"; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - ethphy1: ethernet-phy@1 { - reg = <1>; - }; - - ethphy2: ethernet-phy@2 { - reg = <2>; - }; - }; -}; - -&fec2 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_enet2>; - phy-mode = "rgmii"; - phy-handle = <ðphy2>; - status = "okay"; +&cpu0 { + operating-points = < + /* kHz uV */ + 996000 1250000 + 792000 1175000 + 396000 1175000 + >; + fsl,soc-operating-points = < + /* ARM kHz SOC uV */ + 996000 1250000 + 792000 1175000 + 396000 1175000 + >; }; &i2c1 { - clock-frequency = <100000>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1>; - status = "okay"; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; pmic: pfuze100@08 { - compatible = "fsl,pfuze100"; + compatible = "fsl,pfuze200"; reg = <0x08>; regulators { @@ -203,14 +46,6 @@ regulator-ramp-delay = <6250>; }; - sw1c_reg: sw1c { - regulator-min-microvolt = <300000>; - regulator-max-microvolt = <1875000>; - regulator-boot-on; - regulator-always-on; - regulator-ramp-delay = <6250>; - }; - sw2_reg: sw2 { regulator-min-microvolt = <800000>; regulator-max-microvolt = <3300000>; @@ -232,11 +67,6 @@ regulator-always-on; }; - sw4_reg: sw4 { - regulator-min-microvolt = <800000>; - regulator-max-microvolt = <3300000>; - }; - swbst_reg: swbst { regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5150000>; @@ -292,401 +122,24 @@ }; }; -&i2c4 { - clock-frequency = <100000>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c4>; - status = "okay"; - - codec: wm8962@1a { - compatible = "wlf,wm8962"; - reg = <0x1a>; - clocks = <&clks IMX6SX_CLK_AUDIO>; - DCVDD-supply = <&vgen4_reg>; - DBVDD-supply = <&vgen4_reg>; - AVDD-supply = <&vgen4_reg>; - CPVDD-supply = <&vgen4_reg>; - MICVDD-supply = <&vgen3_reg>; - PLLVDD-supply = <&vgen4_reg>; - SPKVDD1-supply = <®_psu_5v>; - SPKVDD2-supply = <®_psu_5v>; - }; -}; - -&lcdif1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_lcd>; - lcd-supply = <®_lcd_3v3>; - display = <&display0>; - status = "okay"; - - display0: display0 { - bits-per-pixel = <16>; - bus-width = <24>; - - display-timings { - native-mode = <&timing0>; - timing0: timing0 { - clock-frequency = <33500000>; - hactive = <800>; - vactive = <480>; - hback-porch = <89>; - hfront-porch = <164>; - vback-porch = <23>; - vfront-porch = <10>; - hsync-len = <10>; - vsync-len = <10>; - hsync-active = <0>; - vsync-active = <0>; - de-active = <1>; - pixelclk-active = <0>; - }; - }; - }; -}; - -&pwm3 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_pwm3>; - status = "okay"; -}; - -&snvs_poweroff { - status = "okay"; -}; - &qspi2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_qspi2>; status = "okay"; - flash0: s25fl128s@0 { + flash0: n25q256a@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q256a"; + spi-max-frequency = <29000000>; reg = <0>; - #address-cells = <1>; - #size-cells = <1>; - compatible = "spansion,s25fl128s"; - spi-max-frequency = <66000000>; }; - flash1: s25fl128s@1 { + flash1: n25q256a@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q256a"; + spi-max-frequency = <29000000>; reg = <1>; - #address-cells = <1>; - #size-cells = <1>; - compatible = "spansion,s25fl128s"; - spi-max-frequency = <66000000>; - }; -}; - -&ssi2 { - status = "okay"; -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1>; - status = "okay"; -}; - -&uart5 { /* for bluetooth */ - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart5>; - fsl,uart-has-rtscts; - status = "okay"; -}; - -&usbotg1 { - vbus-supply = <®_usb_otg1_vbus>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usb_otg1_id>; - status = "okay"; -}; - -&usbotg2 { - vbus-supply = <®_usb_otg2_vbus>; - dr_mode = "host"; - status = "okay"; -}; - -&usdhc2 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc2>; - non-removable; - no-1-8-v; - keep-power-in-suspend; - enable-sdio-wakeup; - status = "okay"; -}; - -&usdhc3 { - pinctrl-names = "default", "state_100mhz", "state_200mhz"; - pinctrl-0 = <&pinctrl_usdhc3>; - pinctrl-1 = <&pinctrl_usdhc3_100mhz>; - pinctrl-2 = <&pinctrl_usdhc3_200mhz>; - bus-width = <8>; - cd-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>; - wp-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>; - keep-power-in-suspend; - enable-sdio-wakeup; - vmmc-supply = <&vcc_sd3>; - status = "okay"; -}; - -&usdhc4 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc4>; - cd-gpios = <&gpio6 21 GPIO_ACTIVE_HIGH>; - wp-gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>; - status = "okay"; -}; - -&iomuxc { - imx6x-sdb { - pinctrl_audmux: audmuxgrp { - fsl,pins = < - MX6SX_PAD_CSI_DATA00__AUDMUX_AUD6_TXC 0x130b0 - MX6SX_PAD_CSI_DATA01__AUDMUX_AUD6_TXFS 0x130b0 - MX6SX_PAD_CSI_HSYNC__AUDMUX_AUD6_TXD 0x120b0 - MX6SX_PAD_CSI_VSYNC__AUDMUX_AUD6_RXD 0x130b0 - MX6SX_PAD_CSI_PIXCLK__AUDMUX_MCLK 0x130b0 - >; - }; - - pinctrl_enet1: enet1grp { - fsl,pins = < - MX6SX_PAD_ENET1_MDIO__ENET1_MDIO 0xa0b1 - MX6SX_PAD_ENET1_MDC__ENET1_MDC 0xa0b1 - MX6SX_PAD_RGMII1_TXC__ENET1_RGMII_TXC 0xa0b1 - MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0 0xa0b1 - MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1 0xa0b1 - MX6SX_PAD_RGMII1_TD2__ENET1_TX_DATA_2 0xa0b1 - MX6SX_PAD_RGMII1_TD3__ENET1_TX_DATA_3 0xa0b1 - MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN 0xa0b1 - MX6SX_PAD_RGMII1_RXC__ENET1_RX_CLK 0x3081 - MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0 0x3081 - MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 0x3081 - MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2 0x3081 - MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3 0x3081 - MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x3081 - MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M 0x91 - >; - }; - - pinctrl_enet_3v3: enet3v3grp { - fsl,pins = < - MX6SX_PAD_ENET2_COL__GPIO2_IO_6 0x80000000 - >; - }; - - pinctrl_enet2: enet2grp { - fsl,pins = < - MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC 0xa0b9 - MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 0xa0b1 - MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 0xa0b1 - MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2 0xa0b1 - MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3 0xa0b1 - MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN 0xa0b1 - MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK 0x3081 - MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 0x3081 - MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 0x3081 - MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2 0x3081 - MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3 0x3081 - MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN 0x3081 - >; - }; - - pinctrl_gpio_keys: gpio_keysgrp { - fsl,pins = < - MX6SX_PAD_CSI_DATA04__GPIO1_IO_18 0x17059 - MX6SX_PAD_CSI_DATA05__GPIO1_IO_19 0x17059 - >; - }; - - pinctrl_i2c1: i2c1grp { - fsl,pins = < - MX6SX_PAD_GPIO1_IO01__I2C1_SDA 0x4001b8b1 - MX6SX_PAD_GPIO1_IO00__I2C1_SCL 0x4001b8b1 - >; - }; - - pinctrl_i2c4: i2c4grp { - fsl,pins = < - MX6SX_PAD_CSI_DATA07__I2C4_SDA 0x4001b8b1 - MX6SX_PAD_CSI_DATA06__I2C4_SCL 0x4001b8b1 - >; - }; - - pinctrl_lcd: lcdgrp { - fsl,pins = < - MX6SX_PAD_LCD1_DATA00__LCDIF1_DATA_0 0x4001b0b0 - MX6SX_PAD_LCD1_DATA01__LCDIF1_DATA_1 0x4001b0b0 - MX6SX_PAD_LCD1_DATA02__LCDIF1_DATA_2 0x4001b0b0 - MX6SX_PAD_LCD1_DATA03__LCDIF1_DATA_3 0x4001b0b0 - MX6SX_PAD_LCD1_DATA04__LCDIF1_DATA_4 0x4001b0b0 - MX6SX_PAD_LCD1_DATA05__LCDIF1_DATA_5 0x4001b0b0 - MX6SX_PAD_LCD1_DATA06__LCDIF1_DATA_6 0x4001b0b0 - MX6SX_PAD_LCD1_DATA07__LCDIF1_DATA_7 0x4001b0b0 - MX6SX_PAD_LCD1_DATA08__LCDIF1_DATA_8 0x4001b0b0 - MX6SX_PAD_LCD1_DATA09__LCDIF1_DATA_9 0x4001b0b0 - MX6SX_PAD_LCD1_DATA10__LCDIF1_DATA_10 0x4001b0b0 - MX6SX_PAD_LCD1_DATA11__LCDIF1_DATA_11 0x4001b0b0 - MX6SX_PAD_LCD1_DATA12__LCDIF1_DATA_12 0x4001b0b0 - MX6SX_PAD_LCD1_DATA13__LCDIF1_DATA_13 0x4001b0b0 - MX6SX_PAD_LCD1_DATA14__LCDIF1_DATA_14 0x4001b0b0 - MX6SX_PAD_LCD1_DATA15__LCDIF1_DATA_15 0x4001b0b0 - MX6SX_PAD_LCD1_DATA16__LCDIF1_DATA_16 0x4001b0b0 - MX6SX_PAD_LCD1_DATA17__LCDIF1_DATA_17 0x4001b0b0 - MX6SX_PAD_LCD1_DATA18__LCDIF1_DATA_18 0x4001b0b0 - MX6SX_PAD_LCD1_DATA19__LCDIF1_DATA_19 0x4001b0b0 - MX6SX_PAD_LCD1_DATA20__LCDIF1_DATA_20 0x4001b0b0 - MX6SX_PAD_LCD1_DATA21__LCDIF1_DATA_21 0x4001b0b0 - MX6SX_PAD_LCD1_DATA22__LCDIF1_DATA_22 0x4001b0b0 - MX6SX_PAD_LCD1_DATA23__LCDIF1_DATA_23 0x4001b0b0 - MX6SX_PAD_LCD1_CLK__LCDIF1_CLK 0x4001b0b0 - MX6SX_PAD_LCD1_ENABLE__LCDIF1_ENABLE 0x4001b0b0 - MX6SX_PAD_LCD1_VSYNC__LCDIF1_VSYNC 0x4001b0b0 - MX6SX_PAD_LCD1_HSYNC__LCDIF1_HSYNC 0x4001b0b0 - MX6SX_PAD_LCD1_RESET__GPIO3_IO_27 0x4001b0b0 - >; - }; - - pinctrl_peri_3v3: peri3v3grp { - fsl,pins = < - MX6SX_PAD_QSPI1A_DATA0__GPIO4_IO_16 0x80000000 - >; - }; - - pinctrl_pwm3: pwm3grp-1 { - fsl,pins = < - MX6SX_PAD_SD1_DATA2__PWM3_OUT 0x110b0 - >; - }; - - pinctrl_qspi2: qspi2grp { - fsl,pins = < - MX6SX_PAD_NAND_WP_B__QSPI2_A_DATA_0 0x70f1 - MX6SX_PAD_NAND_READY_B__QSPI2_A_DATA_1 0x70f1 - MX6SX_PAD_NAND_CE0_B__QSPI2_A_DATA_2 0x70f1 - MX6SX_PAD_NAND_CE1_B__QSPI2_A_DATA_3 0x70f1 - MX6SX_PAD_NAND_CLE__QSPI2_A_SCLK 0x70f1 - MX6SX_PAD_NAND_ALE__QSPI2_A_SS0_B 0x70f1 - MX6SX_PAD_NAND_DATA01__QSPI2_B_DATA_0 0x70f1 - MX6SX_PAD_NAND_DATA00__QSPI2_B_DATA_1 0x70f1 - MX6SX_PAD_NAND_WE_B__QSPI2_B_DATA_2 0x70f1 - MX6SX_PAD_NAND_RE_B__QSPI2_B_DATA_3 0x70f1 - MX6SX_PAD_NAND_DATA02__QSPI2_B_SCLK 0x70f1 - MX6SX_PAD_NAND_DATA03__QSPI2_B_SS0_B 0x70f1 - >; - }; - - pinctrl_vcc_sd3: vccsd3grp { - fsl,pins = < - MX6SX_PAD_KEY_COL1__GPIO2_IO_11 0x17059 - >; - }; - - pinctrl_uart1: uart1grp { - fsl,pins = < - MX6SX_PAD_GPIO1_IO04__UART1_TX 0x1b0b1 - MX6SX_PAD_GPIO1_IO05__UART1_RX 0x1b0b1 - >; - }; - - pinctrl_uart5: uart5grp { - fsl,pins = < - MX6SX_PAD_KEY_ROW3__UART5_RX 0x1b0b1 - MX6SX_PAD_KEY_COL3__UART5_TX 0x1b0b1 - MX6SX_PAD_KEY_ROW2__UART5_CTS_B 0x1b0b1 - MX6SX_PAD_KEY_COL2__UART5_RTS_B 0x1b0b1 - >; - }; - - pinctrl_usb_otg1: usbotg1grp { - fsl,pins = < - MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9 0x10b0 - >; - }; - - pinctrl_usb_otg1_id: usbotg1idgrp { - fsl,pins = < - MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID 0x17059 - >; - }; - - pinctrl_usb_otg2: usbot2ggrp { - fsl,pins = < - MX6SX_PAD_GPIO1_IO12__GPIO1_IO_12 0x10b0 - >; - }; - - pinctrl_usdhc2: usdhc2grp { - fsl,pins = < - MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x17059 - MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x10059 - MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x17059 - MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x17059 - MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x17059 - MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x17059 - >; - }; - - pinctrl_usdhc3: usdhc3grp { - fsl,pins = < - MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x17059 - MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x10059 - MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x17059 - MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x17059 - MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x17059 - MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x17059 - MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x17059 - MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x17059 - MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x17059 - MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x17059 - MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x17059 /* CD */ - MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x17059 /* WP */ - >; - }; - - pinctrl_usdhc3_100mhz: usdhc3grp-100mhz { - fsl,pins = < - MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170b9 - MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100b9 - MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170b9 - MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170b9 - MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170b9 - MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170b9 - MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170b9 - MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170b9 - MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170b9 - MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170b9 - >; - }; - - pinctrl_usdhc3_200mhz: usdhc3grp-200mhz { - fsl,pins = < - MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170f9 - MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100f9 - MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170f9 - MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170f9 - MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170f9 - MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170f9 - MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170f9 - MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170f9 - MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170f9 - MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170f9 - >; - }; - - pinctrl_usdhc4: usdhc4grp { - fsl,pins = < - MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x17059 - MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x10059 - MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x17059 - MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x17059 - MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x17059 - MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x17059 - MX6SX_PAD_SD4_DATA7__GPIO6_IO_21 0x17059 /* CD */ - MX6SX_PAD_SD4_DATA6__GPIO6_IO_20 0x17059 /* WP */ - >; - }; }; }; diff --git a/arch/arm/boot/dts/imx6sx-sdb.dtsi b/arch/arm/boot/dts/imx6sx-sdb.dtsi new file mode 100644 index 000000000000..cef04cef3a80 --- /dev/null +++ b/arch/arm/boot/dts/imx6sx-sdb.dtsi @@ -0,0 +1,562 @@ +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include +#include +#include "imx6sx.dtsi" + +/ { + model = "Freescale i.MX6 SoloX SDB Board"; + compatible = "fsl,imx6sx-sdb", "fsl,imx6sx"; + + chosen { + stdout-path = &uart1; + }; + + memory { + reg = <0x80000000 0x40000000>; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm3 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys>; + + volume-up { + label = "Volume Up"; + gpios = <&gpio1 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + volume-down { + label = "Volume Down"; + gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + vcc_sd3: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_vcc_sd3>; + regulator-name = "VCC_SD3"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_otg1_vbus: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg1>; + regulator-name = "usb_otg1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_otg2_vbus: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg2>; + regulator-name = "usb_otg2_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_psu_5v: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "PSU-5V0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_lcd_3v3: regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "lcd-3v3"; + gpio = <&gpio3 27 0>; + enable-active-high; + }; + + reg_peri_3v3: regulator@5 { + compatible = "regulator-fixed"; + reg = <5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_peri_3v3>; + regulator-name = "peri_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + reg_enet_3v3: regulator@6 { + compatible = "regulator-fixed"; + reg = <6>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_3v3>; + regulator-name = "enet_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; + }; + }; + + sound { + compatible = "fsl,imx6sx-sdb-wm8962", "fsl,imx-audio-wm8962"; + model = "wm8962-audio"; + ssi-controller = <&ssi2>; + audio-codec = <&codec>; + audio-routing = + "Headphone Jack", "HPOUTL", + "Headphone Jack", "HPOUTR", + "Ext Spk", "SPKOUTL", + "Ext Spk", "SPKOUTR", + "AMIC", "MICBIAS", + "IN3R", "AMIC"; + mux-int-port = <2>; + mux-ext-port = <6>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1>; + phy-supply = <®_enet_3v3>; + phy-mode = "rgmii"; + phy-handle = <ðphy1>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + reg = <1>; + }; + + ethphy2: ethernet-phy@2 { + reg = <2>; + }; + }; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2>; + phy-mode = "rgmii"; + phy-handle = <ðphy2>; + status = "okay"; +}; + +&i2c4 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + codec: wm8962@1a { + compatible = "wlf,wm8962"; + reg = <0x1a>; + clocks = <&clks IMX6SX_CLK_AUDIO>; + DCVDD-supply = <&vgen4_reg>; + DBVDD-supply = <&vgen4_reg>; + AVDD-supply = <&vgen4_reg>; + CPVDD-supply = <&vgen4_reg>; + MICVDD-supply = <&vgen3_reg>; + PLLVDD-supply = <&vgen4_reg>; + SPKVDD1-supply = <®_psu_5v>; + SPKVDD2-supply = <®_psu_5v>; + }; +}; + +&lcdif1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd>; + lcd-supply = <®_lcd_3v3>; + display = <&display0>; + status = "okay"; + + display0: display0 { + bits-per-pixel = <16>; + bus-width = <24>; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <33500000>; + hactive = <800>; + vactive = <480>; + hback-porch = <89>; + hfront-porch = <164>; + vback-porch = <23>; + vfront-porch = <10>; + hsync-len = <10>; + vsync-len = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "okay"; +}; + +&snvs_poweroff { + status = "okay"; +}; + +&ssi2 { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart5 { /* for bluetooth */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +&usbotg1 { + vbus-supply = <®_usb_otg1_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg1_id>; + status = "okay"; +}; + +&usbotg2 { + vbus-supply = <®_usb_otg2_vbus>; + dr_mode = "host"; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + non-removable; + no-1-8-v; + keep-power-in-suspend; + enable-sdio-wakeup; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + cd-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>; + wp-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>; + keep-power-in-suspend; + enable-sdio-wakeup; + vmmc-supply = <&vcc_sd3>; + status = "okay"; +}; + +&usdhc4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc4>; + cd-gpios = <&gpio6 21 GPIO_ACTIVE_HIGH>; + wp-gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&iomuxc { + imx6x-sdb { + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6SX_PAD_CSI_DATA00__AUDMUX_AUD6_TXC 0x130b0 + MX6SX_PAD_CSI_DATA01__AUDMUX_AUD6_TXFS 0x130b0 + MX6SX_PAD_CSI_HSYNC__AUDMUX_AUD6_TXD 0x120b0 + MX6SX_PAD_CSI_VSYNC__AUDMUX_AUD6_RXD 0x130b0 + MX6SX_PAD_CSI_PIXCLK__AUDMUX_MCLK 0x130b0 + >; + }; + + pinctrl_enet1: enet1grp { + fsl,pins = < + MX6SX_PAD_ENET1_MDIO__ENET1_MDIO 0xa0b1 + MX6SX_PAD_ENET1_MDC__ENET1_MDC 0xa0b1 + MX6SX_PAD_RGMII1_TXC__ENET1_RGMII_TXC 0xa0b1 + MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0 0xa0b1 + MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1 0xa0b1 + MX6SX_PAD_RGMII1_TD2__ENET1_TX_DATA_2 0xa0b1 + MX6SX_PAD_RGMII1_TD3__ENET1_TX_DATA_3 0xa0b1 + MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN 0xa0b1 + MX6SX_PAD_RGMII1_RXC__ENET1_RX_CLK 0x3081 + MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0 0x3081 + MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 0x3081 + MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2 0x3081 + MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3 0x3081 + MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x3081 + MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M 0x91 + >; + }; + + pinctrl_enet_3v3: enet3v3grp { + fsl,pins = < + MX6SX_PAD_ENET2_COL__GPIO2_IO_6 0x80000000 + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC 0xa0b9 + MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 0xa0b1 + MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 0xa0b1 + MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2 0xa0b1 + MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3 0xa0b1 + MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN 0xa0b1 + MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK 0x3081 + MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 0x3081 + MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 0x3081 + MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2 0x3081 + MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3 0x3081 + MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN 0x3081 + >; + }; + + pinctrl_gpio_keys: gpio_keysgrp { + fsl,pins = < + MX6SX_PAD_CSI_DATA04__GPIO1_IO_18 0x17059 + MX6SX_PAD_CSI_DATA05__GPIO1_IO_19 0x17059 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6SX_PAD_GPIO1_IO01__I2C1_SDA 0x4001b8b1 + MX6SX_PAD_GPIO1_IO00__I2C1_SCL 0x4001b8b1 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX6SX_PAD_CSI_DATA07__I2C4_SDA 0x4001b8b1 + MX6SX_PAD_CSI_DATA06__I2C4_SCL 0x4001b8b1 + >; + }; + + pinctrl_lcd: lcdgrp { + fsl,pins = < + MX6SX_PAD_LCD1_DATA00__LCDIF1_DATA_0 0x4001b0b0 + MX6SX_PAD_LCD1_DATA01__LCDIF1_DATA_1 0x4001b0b0 + MX6SX_PAD_LCD1_DATA02__LCDIF1_DATA_2 0x4001b0b0 + MX6SX_PAD_LCD1_DATA03__LCDIF1_DATA_3 0x4001b0b0 + MX6SX_PAD_LCD1_DATA04__LCDIF1_DATA_4 0x4001b0b0 + MX6SX_PAD_LCD1_DATA05__LCDIF1_DATA_5 0x4001b0b0 + MX6SX_PAD_LCD1_DATA06__LCDIF1_DATA_6 0x4001b0b0 + MX6SX_PAD_LCD1_DATA07__LCDIF1_DATA_7 0x4001b0b0 + MX6SX_PAD_LCD1_DATA08__LCDIF1_DATA_8 0x4001b0b0 + MX6SX_PAD_LCD1_DATA09__LCDIF1_DATA_9 0x4001b0b0 + MX6SX_PAD_LCD1_DATA10__LCDIF1_DATA_10 0x4001b0b0 + MX6SX_PAD_LCD1_DATA11__LCDIF1_DATA_11 0x4001b0b0 + MX6SX_PAD_LCD1_DATA12__LCDIF1_DATA_12 0x4001b0b0 + MX6SX_PAD_LCD1_DATA13__LCDIF1_DATA_13 0x4001b0b0 + MX6SX_PAD_LCD1_DATA14__LCDIF1_DATA_14 0x4001b0b0 + MX6SX_PAD_LCD1_DATA15__LCDIF1_DATA_15 0x4001b0b0 + MX6SX_PAD_LCD1_DATA16__LCDIF1_DATA_16 0x4001b0b0 + MX6SX_PAD_LCD1_DATA17__LCDIF1_DATA_17 0x4001b0b0 + MX6SX_PAD_LCD1_DATA18__LCDIF1_DATA_18 0x4001b0b0 + MX6SX_PAD_LCD1_DATA19__LCDIF1_DATA_19 0x4001b0b0 + MX6SX_PAD_LCD1_DATA20__LCDIF1_DATA_20 0x4001b0b0 + MX6SX_PAD_LCD1_DATA21__LCDIF1_DATA_21 0x4001b0b0 + MX6SX_PAD_LCD1_DATA22__LCDIF1_DATA_22 0x4001b0b0 + MX6SX_PAD_LCD1_DATA23__LCDIF1_DATA_23 0x4001b0b0 + MX6SX_PAD_LCD1_CLK__LCDIF1_CLK 0x4001b0b0 + MX6SX_PAD_LCD1_ENABLE__LCDIF1_ENABLE 0x4001b0b0 + MX6SX_PAD_LCD1_VSYNC__LCDIF1_VSYNC 0x4001b0b0 + MX6SX_PAD_LCD1_HSYNC__LCDIF1_HSYNC 0x4001b0b0 + MX6SX_PAD_LCD1_RESET__GPIO3_IO_27 0x4001b0b0 + >; + }; + + pinctrl_peri_3v3: peri3v3grp { + fsl,pins = < + MX6SX_PAD_QSPI1A_DATA0__GPIO4_IO_16 0x80000000 + >; + }; + + pinctrl_pwm3: pwm3grp-1 { + fsl,pins = < + MX6SX_PAD_SD1_DATA2__PWM3_OUT 0x110b0 + >; + }; + + pinctrl_qspi2: qspi2grp { + fsl,pins = < + MX6SX_PAD_NAND_WP_B__QSPI2_A_DATA_0 0x70f1 + MX6SX_PAD_NAND_READY_B__QSPI2_A_DATA_1 0x70f1 + MX6SX_PAD_NAND_CE0_B__QSPI2_A_DATA_2 0x70f1 + MX6SX_PAD_NAND_CE1_B__QSPI2_A_DATA_3 0x70f1 + MX6SX_PAD_NAND_CLE__QSPI2_A_SCLK 0x70f1 + MX6SX_PAD_NAND_ALE__QSPI2_A_SS0_B 0x70f1 + MX6SX_PAD_NAND_DATA01__QSPI2_B_DATA_0 0x70f1 + MX6SX_PAD_NAND_DATA00__QSPI2_B_DATA_1 0x70f1 + MX6SX_PAD_NAND_WE_B__QSPI2_B_DATA_2 0x70f1 + MX6SX_PAD_NAND_RE_B__QSPI2_B_DATA_3 0x70f1 + MX6SX_PAD_NAND_DATA02__QSPI2_B_SCLK 0x70f1 + MX6SX_PAD_NAND_DATA03__QSPI2_B_SS0_B 0x70f1 + >; + }; + + pinctrl_vcc_sd3: vccsd3grp { + fsl,pins = < + MX6SX_PAD_KEY_COL1__GPIO2_IO_11 0x17059 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6SX_PAD_GPIO1_IO04__UART1_TX 0x1b0b1 + MX6SX_PAD_GPIO1_IO05__UART1_RX 0x1b0b1 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6SX_PAD_KEY_ROW3__UART5_RX 0x1b0b1 + MX6SX_PAD_KEY_COL3__UART5_TX 0x1b0b1 + MX6SX_PAD_KEY_ROW2__UART5_CTS_B 0x1b0b1 + MX6SX_PAD_KEY_COL2__UART5_RTS_B 0x1b0b1 + >; + }; + + pinctrl_usb_otg1: usbotg1grp { + fsl,pins = < + MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9 0x10b0 + >; + }; + + pinctrl_usb_otg1_id: usbotg1idgrp { + fsl,pins = < + MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID 0x17059 + >; + }; + + pinctrl_usb_otg2: usbot2ggrp { + fsl,pins = < + MX6SX_PAD_GPIO1_IO12__GPIO1_IO_12 0x10b0 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x17059 + MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x10059 + MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x17059 + MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x17059 + MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x17059 + MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x17059 + MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x10059 + MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x17059 + MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x17059 + MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x17059 + MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x17059 + MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x17059 + MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x17059 + MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x17059 + MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x17059 + MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x17059 /* CD */ + MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x17059 /* WP */ + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3grp-100mhz { + fsl,pins = < + MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170b9 + MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100b9 + MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170b9 + MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170b9 + MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170b9 + MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170b9 + MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170b9 + MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170b9 + MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170b9 + MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170b9 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3grp-200mhz { + fsl,pins = < + MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170f9 + MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100f9 + MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170f9 + MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170f9 + MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170f9 + MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170f9 + MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170f9 + MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170f9 + MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170f9 + MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170f9 + >; + }; + + pinctrl_usdhc4: usdhc4grp { + fsl,pins = < + MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x17059 + MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x10059 + MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x17059 + MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x17059 + MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x17059 + MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x17059 + MX6SX_PAD_SD4_DATA7__GPIO6_IO_21 0x17059 /* CD */ + MX6SX_PAD_SD4_DATA6__GPIO6_IO_20 0x17059 /* WP */ + >; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi index 7a24fee1e7ae..708175d59b9c 100644 --- a/arch/arm/boot/dts/imx6sx.dtsi +++ b/arch/arm/boot/dts/imx6sx.dtsi @@ -88,6 +88,7 @@ interrupt-controller; reg = <0x00a01000 0x1000>, <0x00a00100 0x100>; + interrupt-parent = <&intc>; }; clocks { @@ -131,7 +132,7 @@ #address-cells = <1>; #size-cells = <1>; compatible = "simple-bus"; - interrupt-parent = <&intc>; + interrupt-parent = <&gpc>; ranges; pmu { @@ -666,7 +667,7 @@ #size-cells = <1>; ranges = <0 0x020cc000 0x4000>; - snvs-rtc-lp@34 { + snvs_rtc: snvs-rtc-lp@34 { compatible = "fsl,sec-v4.0-mon-rtc-lp"; reg = <0x34 0x58>; interrupts = , ; @@ -700,7 +701,10 @@ gpc: gpc@020dc000 { compatible = "fsl,imx6sx-gpc", "fsl,imx6q-gpc"; reg = <0x020dc000 0x4000>; + interrupt-controller; + #interrupt-cells = <3>; interrupts = ; + interrupt-parent = <&intc>; }; iomuxc: iomuxc@020e0000 { @@ -763,6 +767,7 @@ fsl,usbmisc = <&usbmisc 2>; phy_type = "hsic"; fsl,anatop = <&anatop>; + dr_mode = "host"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/kirkwood-nas2big.dts b/arch/arm/boot/dts/kirkwood-nas2big.dts new file mode 100644 index 000000000000..7427ec50b829 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-nas2big.dts @@ -0,0 +1,143 @@ +/* + * Device Tree file for LaCie 2Big NAS + * + * Copyright (C) 2015 Seagate + * + * Author: Simon Guinot + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. +*/ + +/dts-v1/; + +#include "kirkwood-netxbig.dtsi" + +/ { + model = "LaCie 2Big NAS"; + compatible = "lacie,nas2big", "lacie,netxbig", "marvell,kirkwood-88f6282", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = &uart0; + }; + + mbus { + pcie-controller { + status = "okay"; + + pcie@1,0 { + status = "okay"; + }; + }; + }; + + ocp@f1000000 { + rtc@10300 { + /* The on-chip RTC is not powered (no supercap). */ + status = "disabled"; + }; + spi@10600 { + /* + * A NAND flash is used instead of an SPI flash for + * the other netxbig-compatible boards. + */ + status = "disabled"; + }; + }; + + fan { + /* + * An I2C fan controller (GMT G762) is used but alarm is + * wired to a separate GPIO. + */ + compatible = "gpio-fan"; + alarm-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; + }; + + regulators: regulators { + status = "okay"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + + regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "hdd1power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 17 GPIO_ACTIVE_HIGH>; + }; + clocks { + g762_clk: g762-oscillator { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +&i2c0 { + status = "okay"; + + /* + * An external I2C RTC (Dallas DS1337S+) is used. This allows + * to power-up the board on an RTC alarm. The external RTC can + * be kept powered, even when the SoC is off. + */ + rtc@68 { + compatible = "dallas,ds1307"; + reg = <0x68>; + interrupts = <43>; + }; + g762@3e { + compatible = "gmt,g762"; + reg = <0x3e>; + clocks = <&g762_clk>; + }; +}; + +&nand { + chip-delay = <50>; + status = "okay"; + + partition@0 { + label = "U-Boot"; + reg = <0x0 0x100000>; + }; + + partition@100000 { + label = "uImage"; + reg = <0x100000 0x1000000>; + }; + + partition@1100000 { + label = "root"; + reg = <0x1100000 0x8000000>; + }; + + partition@9100000 { + label = "unused"; + reg = <0x9100000 0x6f00000>; + }; +}; diff --git a/arch/arm/boot/dts/kirkwood-net2big.dts b/arch/arm/boot/dts/kirkwood-net2big.dts index 53dc37a3b687..13a44773b6df 100644 --- a/arch/arm/boot/dts/kirkwood-net2big.dts +++ b/arch/arm/boot/dts/kirkwood-net2big.dts @@ -27,6 +27,11 @@ device_type = "memory"; reg = <0x00000000 0x10000000>; }; + + fan { + compatible = "gpio-fan"; + alarm-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; + }; }; ®ulators { diff --git a/arch/arm/boot/dts/meson.dtsi b/arch/arm/boot/dts/meson.dtsi index b67ede515bcd..548441384d2a 100644 --- a/arch/arm/boot/dts/meson.dtsi +++ b/arch/arm/boot/dts/meson.dtsi @@ -150,5 +150,25 @@ interrupts = <0 15 1>; status = "disabled"; }; + + spifc: spi@c1108c80 { + compatible = "amlogic,meson6-spifc"; + reg = <0xc1108c80 0x80>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk81>; + status = "disabled"; + }; + + ethmac: ethernet@c9410000 { + compatible = "amlogic,meson6-dwmac", "snps,dwmac"; + reg = <0xc9410000 0x10000 + 0xc1108108 0x4>; + interrupts = <0 8 1>; + interrupt-names = "macirq"; + clocks = <&clk81>; + clock-names = "stmmaceth"; + status = "disabled"; + }; }; }; /* end of / */ diff --git a/arch/arm/boot/dts/meson6-atv1200.dts b/arch/arm/boot/dts/meson6-atv1200.dts index d7d351a68944..1237faa63ce6 100644 --- a/arch/arm/boot/dts/meson6-atv1200.dts +++ b/arch/arm/boot/dts/meson6-atv1200.dts @@ -64,3 +64,7 @@ &uart_AO { status = "okay"; }; + +ðmac { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/meson8-minix-neo-x8.dts b/arch/arm/boot/dts/meson8-minix-neo-x8.dts new file mode 100644 index 000000000000..4f536bb1f002 --- /dev/null +++ b/arch/arm/boot/dts/meson8-minix-neo-x8.dts @@ -0,0 +1,128 @@ +/* + * Copyright 2014 Beniamino Galvani + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include +#include "meson8.dtsi" + +/ { + model = "MINIX NEO-X8"; + compatible = "minix,neo-x8", "amlogic,meson8"; + + aliases { + serial0 = &uart_AO; + }; + + memory { + reg = <0x40000000 0x80000000>; + }; + + gpio-leds { + compatible = "gpio-leds"; + + blue { + label = "x8:blue:power"; + gpios = <&gpio_ao GPIO_TEST_N GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&i2c_AO { + status = "okay"; + pinctrl-0 = <&i2c_ao_pins>; + pinctrl-names = "default"; + + pmic@32 { + compatible = "ricoh,rn5t618"; + reg = <0x32>; + + regulators { + }; + }; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +&spifc { + status = "okay"; + pinctrl-0 = <&spi_nor_pins>; + pinctrl-names = "default"; + + spi-flash@0 { + compatible = "mxicy,mx25l1606e"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-max-frequency = <30000000>; + + partition@0 { + label = "boot"; + reg = <0x0 0x100000>; + }; + + partition@100000 { + label = "env"; + reg = <0x100000 0x10000>; + }; + }; +}; + +&ir_receiver { + status = "okay"; + pinctrl-0 = <&ir_recv_pins>; + pinctrl-names = "default"; +}; + +ðmac { + status = "okay"; + pinctrl-0 = <ð_pins>; + pnictrl-names = "default"; +}; diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi index 1f442a7fe03b..a2ddcb8c545a 100644 --- a/arch/arm/boot/dts/meson8.dtsi +++ b/arch/arm/boot/dts/meson8.dtsi @@ -43,6 +43,7 @@ * OTHER DEALINGS IN THE SOFTWARE. */ +#include /include/ "meson.dtsi" / { @@ -89,4 +90,71 @@ compatible = "fixed-clock"; clock-frequency = <141666666>; }; + + pinctrl: pinctrl@c1109880 { + compatible = "amlogic,meson8-pinctrl"; + reg = <0xc1109880 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio: banks@c11080b0 { + reg = <0xc11080b0 0x28>, + <0xc11080e8 0x18>, + <0xc1108120 0x18>, + <0xc1108030 0x30>; + reg-names = "mux", "pull", "pull-enable", "gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio_ao: ao-bank@c1108030 { + reg = <0xc8100014 0x4>, + <0xc810002c 0x4>, + <0xc8100024 0x8>; + reg-names = "mux", "pull", "gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + uart_ao_a_pins: uart_ao_a { + mux { + groups = "uart_tx_ao_a", "uart_rx_ao_a"; + function = "uart_ao"; + }; + }; + + i2c_ao_pins: i2c_mst_ao { + mux { + groups = "i2c_mst_sck_ao", "i2c_mst_sda_ao"; + function = "i2c_mst_ao"; + }; + }; + + spi_nor_pins: nor { + mux { + groups = "nor_d", "nor_q", "nor_c", "nor_cs"; + function = "nor"; + }; + }; + + ir_recv_pins: remote { + mux { + groups = "remote_input"; + function = "remote"; + }; + }; + + eth_pins: ethernet { + mux { + groups = "eth_tx_clk_50m", "eth_tx_en", + "eth_txd1", "eth_txd0", + "eth_rx_clk_in", "eth_rx_dv", + "eth_rxd1", "eth_rxd0", "eth_mdio", + "eth_mdc"; + function = "ethernet"; + }; + }; + }; + }; /* end of / */ diff --git a/arch/arm/boot/dts/mt6589.dtsi b/arch/arm/boot/dts/mt6589.dtsi index 106b61b10030..88b3cb128698 100644 --- a/arch/arm/boot/dts/mt6589.dtsi +++ b/arch/arm/boot/dts/mt6589.dtsi @@ -138,5 +138,10 @@ clocks = <&uart_clk>; status = "disabled"; }; + + wdt: watchdog@010000000 { + compatible = "mediatek,mt6589-wdt"; + reg = <0x10000000 0x44>; + }; }; }; diff --git a/arch/arm/boot/dts/nspire-classic.dtsi b/arch/arm/boot/dts/nspire-classic.dtsi index 9565199bce7a..4907c5085d4b 100644 --- a/arch/arm/boot/dts/nspire-classic.dtsi +++ b/arch/arm/boot/dts/nspire-classic.dtsi @@ -51,6 +51,11 @@ compatible = "lsi,nspire-classic-ahb-divider"; }; + +&vbus_reg { + gpio = <&gpio 5 0>; +}; + / { memory { device_type = "memory"; diff --git a/arch/arm/boot/dts/nspire-cx.dts b/arch/arm/boot/dts/nspire-cx.dts index 375b924f60d8..08e0b81b3385 100644 --- a/arch/arm/boot/dts/nspire-cx.dts +++ b/arch/arm/boot/dts/nspire-cx.dts @@ -69,6 +69,10 @@ 0x0709001d 0x070a0033 >; }; +&vbus_reg { + gpio = <&gpio 2 0>; +}; + / { model = "TI-NSPIRE CX"; compatible = "ti,nspire-cx"; diff --git a/arch/arm/boot/dts/nspire.dtsi b/arch/arm/boot/dts/nspire.dtsi index a22ffe633b49..390c91aea16d 100644 --- a/arch/arm/boot/dts/nspire.dtsi +++ b/arch/arm/boot/dts/nspire.dtsi @@ -54,6 +54,20 @@ clocks = <&ahb_clk>; }; + usb_phy: usb_phy { + compatible = "usb-nop-xceiv"; + }; + + vbus_reg: vbus_reg { + compatible = "regulator-fixed"; + + regulator-name = "USB VBUS output"; + regulator-type = "voltage"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + ahb { compatible = "simple-bus"; #address-cells = <1>; @@ -65,8 +79,12 @@ }; usb0: usb@B0000000 { + compatible = "lsi,zevio-usb"; reg = <0xB0000000 0x1000>; interrupts = <8>; + + usb-phy = <&usb_phy>; + vbus-supply = <&vbus_reg>; }; usb1: usb@B4000000 { @@ -105,8 +123,11 @@ ranges; gpio: gpio@90000000 { + compatible = "lsi,zevio-gpio"; reg = <0x90000000 0x1000>; interrupts = <7>; + gpio-controller; + #gpio-cells = <2>; }; fast_timer: timer@90010000 { diff --git a/arch/arm/boot/dts/omap2420.dtsi b/arch/arm/boot/dts/omap2420.dtsi index e2b2e93d7b61..5b9a376cc31e 100644 --- a/arch/arm/boot/dts/omap2420.dtsi +++ b/arch/arm/boot/dts/omap2420.dtsi @@ -14,45 +14,63 @@ compatible = "ti,omap2420", "ti,omap2"; ocp { - prcm: prcm@48008000 { - compatible = "ti,omap2-prcm"; - reg = <0x48008000 0x1000>; - - prcm_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - prcm_clockdomains: clockdomains { - }; - }; - - scrm: scrm@48000000 { - compatible = "ti,omap2-scrm"; - reg = <0x48000000 0x1000>; - - scrm_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - scrm_clockdomains: clockdomains { - }; - }; - - counter32k: counter@48004000 { - compatible = "ti,omap-counter32k"; - reg = <0x48004000 0x20>; - ti,hwmods = "counter_32k"; - }; - - omap2420_pmx: pinmux@48000030 { - compatible = "ti,omap2420-padconf", "pinctrl-single"; - reg = <0x48000030 0x0113>; + l4: l4@48000000 { + compatible = "ti,omap2-l4", "simple-bus"; #address-cells = <1>; - #size-cells = <0>; - pinctrl-single,register-width = <8>; - pinctrl-single,function-mask = <0x3f>; + #size-cells = <1>; + ranges = <0 0x48000000 0x100000>; + + prcm: prcm@8000 { + compatible = "ti,omap2-prcm"; + reg = <0x8000 0x1000>; + + prcm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + prcm_clockdomains: clockdomains { + }; + }; + + scm: scm@0 { + compatible = "ti,omap2-scm", "simple-bus"; + reg = <0x0 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0 0x1000>; + + omap2420_pmx: pinmux@30 { + compatible = "ti,omap2420-padconf", + "pinctrl-single"; + reg = <0x30 0x0113>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-single,register-width = <8>; + pinctrl-single,function-mask = <0x3f>; + }; + + scm_conf: scm_conf@270 { + compatible = "syscon"; + reg = <0x270 0x100>; + #address-cells = <1>; + #size-cells = <1>; + + scm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + scm_clockdomains: clockdomains { + }; + }; + + counter32k: counter@4000 { + compatible = "ti,omap-counter32k"; + reg = <0x4000 0x20>; + ti,hwmods = "counter_32k"; + }; }; gpio1: gpio@48018000 { diff --git a/arch/arm/boot/dts/omap2430-clocks.dtsi b/arch/arm/boot/dts/omap2430-clocks.dtsi index 805f75df1cf2..93fed68839b9 100644 --- a/arch/arm/boot/dts/omap2430-clocks.dtsi +++ b/arch/arm/boot/dts/omap2430-clocks.dtsi @@ -8,12 +8,12 @@ * published by the Free Software Foundation. */ -&scrm_clocks { +&scm_clocks { mcbsp3_mux_fck: mcbsp3_mux_fck { #clock-cells = <0>; compatible = "ti,composite-mux-clock"; clocks = <&func_96m_ck>, <&mcbsp_clks>; - reg = <0x02e8>; + reg = <0x78>; }; mcbsp3_fck: mcbsp3_fck { @@ -27,7 +27,7 @@ compatible = "ti,composite-mux-clock"; clocks = <&func_96m_ck>, <&mcbsp_clks>; ti,bit-shift = <2>; - reg = <0x02e8>; + reg = <0x78>; }; mcbsp4_fck: mcbsp4_fck { @@ -41,7 +41,7 @@ compatible = "ti,composite-mux-clock"; clocks = <&func_96m_ck>, <&mcbsp_clks>; ti,bit-shift = <4>; - reg = <0x02e8>; + reg = <0x78>; }; mcbsp5_fck: mcbsp5_fck { diff --git a/arch/arm/boot/dts/omap2430.dtsi b/arch/arm/boot/dts/omap2430.dtsi index 0dc8de2782b1..11a7963be003 100644 --- a/arch/arm/boot/dts/omap2430.dtsi +++ b/arch/arm/boot/dts/omap2430.dtsi @@ -14,60 +14,73 @@ compatible = "ti,omap2430", "ti,omap2"; ocp { - prcm: prcm@49006000 { - compatible = "ti,omap2-prcm"; - reg = <0x49006000 0x1000>; - - prcm_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - prcm_clockdomains: clockdomains { - }; - }; - - scrm: scrm@49002000 { - compatible = "ti,omap2-scrm"; - reg = <0x49002000 0x1000>; - - scrm_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - scrm_clockdomains: clockdomains { - }; - }; - - counter32k: counter@49020000 { - compatible = "ti,omap-counter32k"; - reg = <0x49020000 0x20>; - ti,hwmods = "counter_32k"; - }; - - omap2430_pmx: pinmux@49002030 { - compatible = "ti,omap2430-padconf", "pinctrl-single"; - reg = <0x49002030 0x0154>; + l4_wkup: l4_wkup@49000000 { + compatible = "ti,omap2-l4-wkup", "simple-bus"; #address-cells = <1>; - #size-cells = <0>; - pinctrl-single,register-width = <8>; - pinctrl-single,function-mask = <0x3f>; - }; + #size-cells = <1>; + ranges = <0 0x49000000 0x31000>; - omap2_scm_general: tisyscon@49002270 { - compatible = "syscon"; - reg = <0x49002270 0x240>; - }; + prcm: prcm@6000 { + compatible = "ti,omap2-prcm"; + reg = <0x6000 0x1000>; - pbias_regulator: pbias_regulator { - compatible = "ti,pbias-omap"; - reg = <0x230 0x4>; - syscon = <&omap2_scm_general>; - pbias_mmc_reg: pbias_mmc_omap2430 { - regulator-name = "pbias_mmc_omap2430"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3000000>; + prcm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + prcm_clockdomains: clockdomains { + }; + }; + + scm: scm@2000 { + compatible = "ti,omap2-scm", "simple-bus"; + reg = <0x2000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2000 0x1000>; + + omap2430_pmx: pinmux@30 { + compatible = "ti,omap2430-padconf", + "pinctrl-single"; + reg = <0x30 0x0154>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-single,register-width = <8>; + pinctrl-single,function-mask = <0x3f>; + }; + + scm_conf: scm_conf@270 { + compatible = "syscon"; + reg = <0x270 0x240>; + #address-cells = <1>; + #size-cells = <1>; + + scm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + pbias_regulator: pbias_regulator { + compatible = "ti,pbias-omap"; + reg = <0x230 0x4>; + syscon = <&scm_conf>; + pbias_mmc_reg: pbias_mmc_omap2430 { + regulator-name = "pbias_mmc_omap2430"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; + }; + }; + + scm_clockdomains: clockdomains { + }; + }; + + counter32k: counter@20000 { + compatible = "ti,omap-counter32k"; + reg = <0x20000 0x20>; + ti,hwmods = "counter_32k"; }; }; diff --git a/arch/arm/boot/dts/omap24xx-clocks.dtsi b/arch/arm/boot/dts/omap24xx-clocks.dtsi index a1365ca926eb..63965b876973 100644 --- a/arch/arm/boot/dts/omap24xx-clocks.dtsi +++ b/arch/arm/boot/dts/omap24xx-clocks.dtsi @@ -7,13 +7,13 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -&scrm_clocks { +&scm_clocks { mcbsp1_mux_fck: mcbsp1_mux_fck { #clock-cells = <0>; compatible = "ti,composite-mux-clock"; clocks = <&func_96m_ck>, <&mcbsp_clks>; ti,bit-shift = <2>; - reg = <0x0274>; + reg = <0x4>; }; mcbsp1_fck: mcbsp1_fck { @@ -27,7 +27,7 @@ compatible = "ti,composite-mux-clock"; clocks = <&func_96m_ck>, <&mcbsp_clks>; ti,bit-shift = <6>; - reg = <0x0274>; + reg = <0x4>; }; mcbsp2_fck: mcbsp2_fck { diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index 25f7b0a22114..7c4dca122a91 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -60,7 +60,6 @@ ti,model = "omap3beagle"; ti,mcbsp = <&mcbsp2>; - ti,codec = <&twl_audio>; }; gpio_keys { @@ -150,7 +149,6 @@ compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0x5401b000 0x1000>; - coresight-default-sink; clocks = <&emu_src_ck>; clock-names = "apb_pclk"; port { diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index c792391ef090..a5474113cd50 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -71,7 +71,6 @@ ti,model = "omap3beagle"; ti,mcbsp = <&mcbsp2>; - ti,codec = <&twl_audio>; }; gpio_keys { @@ -145,7 +144,6 @@ compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0x5401b000 0x1000>; - coresight-default-sink; clocks = <&emu_src_ck>; clock-names = "apb_pclk"; port { @@ -379,3 +377,55 @@ }; }; }; + +&gpmc { + status = "ok"; + ranges = <0 0 0x30000000 0x1000000>; /* CS0 space, 16MB */ + + /* Chip select 0 */ + nand@0,0 { + reg = <0 0 4>; /* NAND I/O window, 4 bytes */ + interrupts = <20>; + ti,nand-ecc-opt = "ham1"; + nand-bus-width = <16>; + #address-cells = <1>; + #size-cells = <1>; + + gpmc,device-width = <2>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <36>; + gpmc,cs-wr-off-ns = <36>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <24>; + gpmc,adv-wr-off-ns = <36>; + gpmc,oe-on-ns = <6>; + gpmc,oe-off-ns = <48>; + gpmc,we-on-ns = <6>; + gpmc,we-off-ns = <30>; + gpmc,rd-cycle-ns = <72>; + gpmc,wr-cycle-ns = <72>; + gpmc,access-ns = <54>; + gpmc,wr-access-ns = <30>; + + partition@0 { + label = "X-Loader"; + reg = <0 0x80000>; + }; + partition@80000 { + label = "U-Boot"; + reg = <0x80000 0x1e0000>; + }; + partition@1c0000 { + label = "U-Boot Env"; + reg = <0x260000 0x20000>; + }; + partition@280000 { + label = "Kernel"; + reg = <0x280000 0x400000>; + }; + partition@780000 { + label = "Filesystem"; + reg = <0x680000 0xf980000>; + }; + }; +}; diff --git a/arch/arm/boot/dts/omap3-cm-t3517.dts b/arch/arm/boot/dts/omap3-cm-t3517.dts index 0ab748cf7749..f5b5a1d96cd7 100644 --- a/arch/arm/boot/dts/omap3-cm-t3517.dts +++ b/arch/arm/boot/dts/omap3-cm-t3517.dts @@ -133,6 +133,16 @@ non-removable; bus-width = <4>; cap-power-off-card; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1271"; + reg = <2>; + interrupt-parent = <&gpio5>; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; /* gpio 145 */ + ref-clock-frequency = <38400000>; + }; }; &dss { diff --git a/arch/arm/boot/dts/omap3-cm-t3730.dts b/arch/arm/boot/dts/omap3-cm-t3730.dts index 46eadb21b5ef..2294f5b0aa10 100644 --- a/arch/arm/boot/dts/omap3-cm-t3730.dts +++ b/arch/arm/boot/dts/omap3-cm-t3730.dts @@ -73,6 +73,16 @@ non-removable; bus-width = <4>; cap-power-off-card; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1271"; + reg = <2>; + interrupt-parent = <&gpio5>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; /* gpio 136 */ + ref-clock-frequency = <38400000>; + }; }; &dss { diff --git a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi index d9e92b654f85..046cd7733c4f 100644 --- a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi +++ b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi @@ -16,7 +16,6 @@ ti,model = "cm-t35"; ti,mcbsp = <&mcbsp2>; - ti,codec = <&twl_audio>; }; }; diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts b/arch/arm/boot/dts/omap3-devkit8000.dts index 169037e5ff53..134d3f27a8ec 100644 --- a/arch/arm/boot/dts/omap3-devkit8000.dts +++ b/arch/arm/boot/dts/omap3-devkit8000.dts @@ -48,7 +48,6 @@ ti,model = "devkit8000"; ti,mcbsp = <&mcbsp2>; - ti,codec = <&twl_audio>; ti,audio-routing = "Ext Spk", "PREDRIVEL", "Ext Spk", "PREDRIVER", diff --git a/arch/arm/boot/dts/omap3-evm-common.dtsi b/arch/arm/boot/dts/omap3-evm-common.dtsi index 127f3e7c10c4..346552b94d9f 100644 --- a/arch/arm/boot/dts/omap3-evm-common.dtsi +++ b/arch/arm/boot/dts/omap3-evm-common.dtsi @@ -106,6 +106,16 @@ non-removable; bus-width = <4>; cap-power-off-card; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1271"; + reg = <2>; + interrupt-parent = <&gpio5>; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* gpio 149 */ + ref-clock-frequency = <38400000>; + }; }; &twl_gpio { diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi index fb3a69604ed5..b9f68817bd6e 100644 --- a/arch/arm/boot/dts/omap3-gta04.dtsi +++ b/arch/arm/boot/dts/omap3-gta04.dtsi @@ -46,7 +46,6 @@ ti,model = "gta04"; ti,mcbsp = <&mcbsp2>; - ti,codec = <&twl_audio>; }; spi_lcd { diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index 8a63ad2286aa..d5e5cd449b16 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -22,7 +22,6 @@ compatible = "ti,omap-twl4030"; ti,model = "igep2"; ti,mcbsp = <&mcbsp2>; - ti,codec = <&twl_audio>; }; vdd33: regulator-vdd33 { diff --git a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts b/arch/arm/boot/dts/omap3-igep0020-rev-f.dts index cc8bd0cd8cf8..72f7cdc091fb 100644 --- a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts +++ b/arch/arm/boot/dts/omap3-igep0020-rev-f.dts @@ -42,4 +42,13 @@ vmmc-supply = <&lbep5clwmc_wlen>; bus-width = <4>; non-removable; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio6>; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; /* gpio 177 */ + }; }; diff --git a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts b/arch/arm/boot/dts/omap3-igep0030-rev-g.dts index 9326b282c94a..b899e341874a 100644 --- a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts +++ b/arch/arm/boot/dts/omap3-igep0030-rev-g.dts @@ -64,4 +64,13 @@ vmmc-supply = <&lbep5clwmc_wlen>; bus-width = <4>; non-removable; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio5>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; /* gpio 136 */ + }; }; diff --git a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi index e81fb651d5d0..e63133304a34 100644 --- a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi +++ b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi @@ -38,7 +38,6 @@ ti,model = "lilly-a83x"; ti,mcbsp = <&mcbsp2>; - ti,codec = <&twl_audio>; }; reg_vcc3: vcc3 { diff --git a/arch/arm/boot/dts/omap3-n9.dts b/arch/arm/boot/dts/omap3-n9.dts index 9938b5dc1909..f2e213931e09 100644 --- a/arch/arm/boot/dts/omap3-n9.dts +++ b/arch/arm/boot/dts/omap3-n9.dts @@ -16,3 +16,40 @@ model = "Nokia N9"; compatible = "nokia,omap3-n9", "ti,omap36xx", "ti,omap3"; }; + +&i2c2 { + smia_1: camera@10 { + compatible = "nokia,smia"; + reg = <0x10>; + /* No reset gpio */ + vana-supply = <&vaux3>; + clocks = <&isp 0>; + clock-frequency = <9600000>; + nokia,nvm-size = <(16 * 64)>; + port { + smia_1_1: endpoint { + link-frequencies = /bits/ 64 <199200000 210000000 499200000>; + clock-lanes = <0>; + data-lanes = <1 2>; + remote-endpoint = <&csi2a_ep>; + }; + }; + }; +}; + +&isp { + vdd-csiphy1-supply = <&vaux2>; + vdd-csiphy2-supply = <&vaux2>; + ports { + port@2 { + reg = <2>; + csi2a_ep: endpoint { + remote-endpoint = <&smia_1_1>; + clock-lanes = <2>; + data-lanes = <1 3>; + crc = <1>; + lane-polarities = <1 1 1>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index db80f9d376fa..5c16145920ea 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -9,9 +9,23 @@ /dts-v1/; -#include "omap34xx-hs.dtsi" +#include "omap34xx.dtsi" #include +/* + * Default secure signed bootloader (Nokia X-Loader) does not enable L3 firewall + * for omap AES HW crypto support. When linux kernel try to access memory of AES + * blocks then kernel receive "Unhandled fault: external abort on non-linefetch" + * and crash. Until somebody fix omap-aes.c and omap_hwmod_3xxx_data.c code (no + * crash anymore) omap AES support will be disabled for all Nokia N900 devices. + * There is "unofficial" version of bootloader which enables AES in L3 firewall + * but it is not widely used and to prevent kernel crash rather AES is disabled. + * There is also no runtime detection code if AES is disabled in L3 firewall... + */ +&aes { + status = "disabled"; +}; + / { model = "Nokia N900"; compatible = "nokia,omap3-n900", "ti,omap3430", "ti,omap3"; @@ -484,6 +498,8 @@ DRVDD-supply = <&vmmc2>; IOVDD-supply = <&vio>; DVDD-supply = <&vio>; + + ai3x-micbias-vg = <1>; }; tlv320aic3x_aux: tlv320aic3x@19 { @@ -495,6 +511,8 @@ DRVDD-supply = <&vmmc2>; IOVDD-supply = <&vio>; DVDD-supply = <&vio>; + + ai3x-micbias-vg = <2>; }; tsl2563: tsl2563@29 { @@ -609,6 +627,58 @@ pinctrl-0 = <&i2c3_pins>; clock-frequency = <400000>; + + lis302dl: lis3lv02d@1d { + compatible = "st,lis3lv02d"; + reg = <0x1d>; + + Vdd-supply = <&vaux1>; + Vdd_IO-supply = <&vio>; + + interrupt-parent = <&gpio6>; + interrupts = <21 20>; /* 181 and 180 */ + + /* click flags */ + st,click-single-x; + st,click-single-y; + st,click-single-z; + + /* Limits are 0.5g * value */ + st,click-threshold-x = <8>; + st,click-threshold-y = <8>; + st,click-threshold-z = <10>; + + /* Click must be longer than time limit */ + st,click-time-limit = <9>; + + /* Kind of debounce filter */ + st,click-latency = <50>; + + /* Interrupt line 2 for click detection */ + st,irq2-click; + + st,wakeup-x-hi; + st,wakeup-y-hi; + st,wakeup-threshold = <(800/18)>; /* millig-value / 18 to get HW values */ + + st,wakeup2-z-hi; + st,wakeup2-threshold = <(900/18)>; /* millig-value / 18 to get HW values */ + + st,hipass1-disable; + st,hipass2-disable; + + st,axis-x = <1>; /* LIS3_DEV_X */ + st,axis-y = <(-2)>; /* LIS3_INV_DEV_Y */ + st,axis-z = <(-3)>; /* LIS3_INV_DEV_Z */ + + st,min-limit-x = <(-32)>; + st,min-limit-y = <3>; + st,min-limit-z = <3>; + + st,max-limit-x = <(-3)>; + st,max-limit-y = <32>; + st,max-limit-z = <32>; + }; }; &mmc1 { diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/omap3-n950-n9.dtsi index c41db94ee9c2..800b379d368d 100644 --- a/arch/arm/boot/dts/omap3-n950-n9.dtsi +++ b/arch/arm/boot/dts/omap3-n950-n9.dtsi @@ -8,7 +8,7 @@ * published by the Free Software Foundation. */ -#include "omap36xx-hs.dtsi" +#include "omap36xx.dtsi" / { cpus { diff --git a/arch/arm/boot/dts/omap3-n950.dts b/arch/arm/boot/dts/omap3-n950.dts index 261c5589bfa3..0885b34d5d7d 100644 --- a/arch/arm/boot/dts/omap3-n950.dts +++ b/arch/arm/boot/dts/omap3-n950.dts @@ -16,3 +16,40 @@ model = "Nokia N950"; compatible = "nokia,omap3-n950", "ti,omap36xx", "ti,omap3"; }; + +&i2c2 { + smia_1: camera@10 { + compatible = "nokia,smia"; + reg = <0x10>; + /* No reset gpio */ + vana-supply = <&vaux3>; + clocks = <&isp 0>; + clock-frequency = <9600000>; + nokia,nvm-size = <(16 * 64)>; + port { + smia_1_1: endpoint { + link-frequencies = /bits/ 64 <210000000 333600000 398400000>; + clock-lanes = <0>; + data-lanes = <1 2>; + remote-endpoint = <&csi2a_ep>; + }; + }; + }; +}; + +&isp { + vdd-csiphy1-supply = <&vaux2>; + vdd-csiphy2-supply = <&vaux2>; + ports { + port@2 { + reg = <2>; + csi2a_ep: endpoint { + remote-endpoint = <&smia_1_1>; + clock-lanes = <2>; + data-lanes = <3 1>; + crc = <1>; + lane-polarities = <1 1 1>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/omap3-overo-base.dtsi b/arch/arm/boot/dts/omap3-overo-base.dtsi index d36bf0250a05..18e1649681c1 100644 --- a/arch/arm/boot/dts/omap3-overo-base.dtsi +++ b/arch/arm/boot/dts/omap3-overo-base.dtsi @@ -27,7 +27,6 @@ ti,model = "overo"; ti,mcbsp = <&mcbsp2>; - ti,codec = <&twl_audio>; }; /* HS USB Port 2 Power */ diff --git a/arch/arm/boot/dts/omap3-pandora-1ghz.dts b/arch/arm/boot/dts/omap3-pandora-1ghz.dts new file mode 100644 index 000000000000..9619a28dfd7d --- /dev/null +++ b/arch/arm/boot/dts/omap3-pandora-1ghz.dts @@ -0,0 +1,70 @@ +/* + * Copyright (C) 2015 + * Nikolaus Schaller + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * device tree for OpenPandora 1GHz with DM3730 + */ + +/dts-v1/; + +#include "omap36xx.dtsi" +#include "omap3-pandora-common.dtsi" + +/ { + model = "Pandora Handheld Console 1GHz"; + + compatible = "ti,omap36xx", "ti,omap3"; +}; + +&omap3_pmx_core2 { + + pinctrl-names = "default"; + pinctrl-0 = < + &hsusb2_2_pins + &control_pins + >; + + hsusb2_2_pins: pinmux_hsusb2_2_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ + OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ + OMAP3630_CORE2_IOPAD(0x25e2, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d3.sdmmc3_dat3 */ + OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d4.sdmmc3_dat0 */ + OMAP3630_CORE2_IOPAD(0x25e6, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d5.sdmmc3_dat1 */ + OMAP3630_CORE2_IOPAD(0x25e8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d6.sdmmc3_dat2 */ + >; + }; + + control_pins: pinmux_control_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT_PULLDOWN | MUX_MODE4) /* etk_d0.gpio_14 = HP_SHUTDOWN */ + OMAP3630_CORE2_IOPAD(0x25de, PIN_OUTPUT | MUX_MODE4) /* etk_d1.gpio_15 = BT_SHUTDOWN */ + OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 = RESET_USB_HOST */ + OMAP3630_CORE2_IOPAD(0x25ea, PIN_INPUT | MUX_MODE4) /* etk_d7.gpio_21 = WIFI IRQ */ + OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4) /* etk_d8.gpio_22 = MSECURE */ + OMAP3630_CORE2_IOPAD(0x25ee, PIN_OUTPUT | MUX_MODE4) /* etk_d9.gpio_23 = WIFI_POWER */ + OMAP3_WKUP_IOPAD(0x2a54, PIN_INPUT | MUX_MODE4) /* reserved.gpio_127 = MMC2_WP */ + OMAP3_WKUP_IOPAD(0x2a56, PIN_INPUT | MUX_MODE4) /* reserved.gpio_126 = MMC1_WP */ + OMAP3_WKUP_IOPAD(0x2a58, PIN_OUTPUT | MUX_MODE4) /* reserved.gpio_128 = LED_MMC1 */ + OMAP3_WKUP_IOPAD(0x2a5a, PIN_OUTPUT | MUX_MODE4) /* reserved.gpio_129 = LED_MMC2 */ + + >; + }; +}; diff --git a/arch/arm/boot/dts/omap3-pandora-600mhz.dts b/arch/arm/boot/dts/omap3-pandora-600mhz.dts new file mode 100644 index 000000000000..fb803a70a2bb --- /dev/null +++ b/arch/arm/boot/dts/omap3-pandora-600mhz.dts @@ -0,0 +1,65 @@ +/* + * Copyright (C) 2015 + * Nikolaus Schaller + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * device tree for OpenPandora with OMAP3530 + */ + +/dts-v1/; + +#include "omap34xx.dtsi" +#include "omap3-pandora-common.dtsi" + +/ { + model = "Pandora Handheld Console"; + + compatible = "ti,omap3"; +}; + +&omap3_pmx_core2 { + + pinctrl-names = "default"; + pinctrl-0 = < + &hsusb2_2_pins + &control_pins + >; + + hsusb2_2_pins: pinmux_hsusb2_2_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ + OMAP3430_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ + OMAP3430_CORE2_IOPAD(0x25e2, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d3.sdmmc3_dat3 */ + OMAP3430_CORE2_IOPAD(0x25e4, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d4.sdmmc3_dat0 */ + OMAP3430_CORE2_IOPAD(0x25e6, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d5.sdmmc3_dat1 */ + OMAP3430_CORE2_IOPAD(0x25e8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d6.sdmmc3_dat2 */ + >; + }; + + control_pins: pinmux_control_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25dc, PIN_INPUT_PULLDOWN | MUX_MODE4) /* etk_d0.gpio_14 = HP_SHUTDOWN */ + OMAP3430_CORE2_IOPAD(0x25de, PIN_OUTPUT | MUX_MODE4) /* etk_d1.gpio_15 = BT_SHUTDOWN */ + OMAP3430_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 = RESET_USB_HOST */ + OMAP3430_CORE2_IOPAD(0x25ea, PIN_INPUT | MUX_MODE4) /* etk_d7.gpio_21 = WIFI IRQ */ + OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4) /* etk_d8.gpio_22 = MSECURE */ + OMAP3430_CORE2_IOPAD(0x25ee, PIN_OUTPUT | MUX_MODE4) /* etk_d9.gpio_23 = WIFI_POWER */ + >; + }; +}; diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/omap3-pandora-common.dtsi new file mode 100644 index 000000000000..782ab1ff1d08 --- /dev/null +++ b/arch/arm/boot/dts/omap3-pandora-common.dtsi @@ -0,0 +1,640 @@ +/* + * Copyright (C) 2015 + * Nikolaus Schaller + * + * Common device tree include for OpenPandora devices. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include + +/ { + cpus { + cpu@0 { + cpu0-supply = <&vcc>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x20000000>; /* 512 MB */ + }; + + aliases { + display0 = &lcd; + }; + + tv: connector@1 { + compatible = "connector-analog-tv"; + label = "tv"; + + port { + tv_connector_in: endpoint { + remote-endpoint = <&venc_out>; + }; + }; + }; + + gpio-leds { + + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + + led@1 { + label = "pandora::sd1"; + gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>; /* GPIO_128 */ + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led@2 { + label = "pandora::sd2"; + gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; /* GPIO_129 */ + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + led@3 { + label = "pandora::bluetooth"; + gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>; /* GPIO_158 */ + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led@4 { + label = "pandora::wifi"; + gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>; /* GPIO_159 */ + linux,default-trigger = "mmc2"; + default-state = "off"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&button_pins>; + + up-button { + label = "up"; + linux,code = ; + gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* GPIO_110 */ + gpio-key,wakeup; + }; + + down-button { + label = "down"; + linux,code = ; + gpios = <&gpio4 7 GPIO_ACTIVE_LOW>; /* GPIO_103 */ + gpio-key,wakeup; + }; + + left-button { + label = "left"; + linux,code = ; + gpios = <&gpio4 0 GPIO_ACTIVE_LOW>; /* GPIO_96 */ + gpio-key,wakeup; + }; + + right-button { + label = "right"; + linux,code = ; + gpios = <&gpio4 2 GPIO_ACTIVE_LOW>; /* GPIO_98 */ + gpio-key,wakeup; + }; + + pageup-button { + label = "game 1"; + linux,code = ; + gpios = <&gpio4 13 GPIO_ACTIVE_LOW>; /* GPIO_109 */ + gpio-key,wakeup; + }; + + pagedown-button { + label = "game 3"; + linux,code = ; + gpios = <&gpio4 10 GPIO_ACTIVE_LOW>; /* GPIO_106 */ + gpio-key,wakeup; + }; + + home-button { + label = "game 4"; + linux,code = ; + gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* GPIO_101 */ + gpio-key,wakeup; + }; + + end-button { + label = "game 2"; + linux,code = ; + gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* GPIO_111 */ + gpio-key,wakeup; + }; + + right-shift { + label = "l"; + linux,code = ; + gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* GPIO_102 */ + gpio-key,wakeup; + }; + + kp-plus { + label = "l2"; + linux,code = ; + gpios = <&gpio4 1 GPIO_ACTIVE_LOW>; /* GPIO_97 */ + gpio-key,wakeup; + }; + + right-ctrl { + label = "r"; + linux,code = ; + gpios = <&gpio4 9 GPIO_ACTIVE_LOW>; /* GPIO_105 */ + gpio-key,wakeup; + }; + + kp-minus { + label = "r2"; + linux,code = ; + gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; /* GPIO_107 */ + gpio-key,wakeup; + }; + + left-ctrl { + label = "ctrl"; + linux,code = ; + gpios = <&gpio4 8 GPIO_ACTIVE_LOW>; /* GPIO_104 */ + gpio-key,wakeup; + }; + + menu { + label = "menu"; + linux,code = ; + gpios = <&gpio4 3 GPIO_ACTIVE_LOW>; /* GPIO_99 */ + gpio-key,wakeup; + }; + + hold { + label = "hold"; + linux,code = ; + gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; /* GPIO_176 */ + gpio-key,wakeup; + }; + + left-alt { + label = "alt"; + linux,code = ; + gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>; /* GPIO_100 */ + gpio-key,wakeup; + }; + + lid { + label = "lid"; + linux,code = <0x00>; /* SW_LID lid shut */ + linux,input-type = <0x05>; /* EV_SW */ + gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; /* GPIO_108 */ + }; + }; +}; + +&omap3_pmx_core { + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dirdat0 */ + OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dirdat1 */ + OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dircmd */ + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */ + >; + }; + + dss_dpi_pins: pinmux_dss_dpi_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ + OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ + OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ + OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ + OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ + OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ + OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ + OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* GPIO_157 = lcd reset */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + >; + }; + + led_pins: pinmux_leds_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2154, PIN_OUTPUT | MUX_MODE4) /* GPIO_128 */ + OMAP3_CORE1_IOPAD(0x2156, PIN_OUTPUT | MUX_MODE4) /* GPIO_129 */ + OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE4) /* GPIO_158 */ + OMAP3_CORE1_IOPAD(0x2192, PIN_OUTPUT | MUX_MODE4) /* GPIO_159 */ + >; + }; + + button_pins: pinmux_button_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT | MUX_MODE4) /* GPIO_96 */ + OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT | MUX_MODE4) /* GPIO_97 */ + OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT | MUX_MODE4) /* GPIO_98 */ + OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT | MUX_MODE4) /* GPIO_99 */ + OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT | MUX_MODE4) /* GPIO_100 */ + OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT | MUX_MODE4) /* GPIO_101 */ + OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE4) /* GPIO_102 */ + OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT | MUX_MODE4) /* GPIO_103 */ + OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT | MUX_MODE4) /* GPIO_104 */ + OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE4) /* GPIO_105 */ + OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE4) /* GPIO_106 */ + OMAP3_CORE1_IOPAD(0x2126, PIN_INPUT | MUX_MODE4) /* GPIO_107 */ + OMAP3_CORE1_IOPAD(0x2128, PIN_INPUT | MUX_MODE4) /* GPIO_108 */ + OMAP3_CORE1_IOPAD(0x212a, PIN_INPUT | MUX_MODE4) /* GPIO_109 */ + OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT | MUX_MODE4) /* GPIO_110 */ + OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT | MUX_MODE4) /* GPIO_111 */ + OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4) /* GPIO_176 */ + >; + }; + + penirq_pins: pinmux_penirq_pins { + pinctrl-single,pins = < + /* here we could enable to wakeup the cpu from suspend by a pen touch */ + OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE4) /* GPIO_94 */ + >; + }; + +}; + +&omap3_pmx_core2 { + /* define in CPU specific file that includes this one + * use either OMAP3430_CORE2_IOPAD() or OMAP3630_CORE2_IOPAD() + */ +}; + +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + twl_power: power { + compatible = "ti,twl4030-power-reset"; + ti,use_poweroff; + }; + + twl_audio: audio { + compatible = "ti,twl4030-audio"; + + codec { + ti,ramp_delay_value = <3>; + }; + }; + }; +}; + +#include "twl4030.dtsi" +#include "twl4030_omap3.dtsi" + +&twl_keypad { + keypad,num-rows = <8>; + keypad,num-columns = <6>; + linux,keymap = < + MATRIX_KEY(0, 0, KEY_9) + MATRIX_KEY(0, 1, KEY_8) + MATRIX_KEY(0, 2, KEY_I) + MATRIX_KEY(0, 3, KEY_J) + MATRIX_KEY(0, 4, KEY_N) + MATRIX_KEY(0, 5, KEY_M) + MATRIX_KEY(1, 0, KEY_0) + MATRIX_KEY(1, 1, KEY_7) + MATRIX_KEY(1, 2, KEY_U) + MATRIX_KEY(1, 3, KEY_H) + MATRIX_KEY(1, 4, KEY_B) + MATRIX_KEY(1, 5, KEY_SPACE) + MATRIX_KEY(2, 0, KEY_BACKSPACE) + MATRIX_KEY(2, 1, KEY_6) + MATRIX_KEY(2, 2, KEY_Y) + MATRIX_KEY(2, 3, KEY_G) + MATRIX_KEY(2, 4, KEY_V) + MATRIX_KEY(2, 5, KEY_FN) + MATRIX_KEY(3, 0, KEY_O) + MATRIX_KEY(3, 1, KEY_5) + MATRIX_KEY(3, 2, KEY_T) + MATRIX_KEY(3, 3, KEY_F) + MATRIX_KEY(3, 4, KEY_C) + MATRIX_KEY(4, 0, KEY_P) + MATRIX_KEY(4, 1, KEY_4) + MATRIX_KEY(4, 2, KEY_R) + MATRIX_KEY(4, 3, KEY_D) + MATRIX_KEY(4, 4, KEY_X) + MATRIX_KEY(5, 0, KEY_K) + MATRIX_KEY(5, 1, KEY_3) + MATRIX_KEY(5, 2, KEY_E) + MATRIX_KEY(5, 3, KEY_S) + MATRIX_KEY(5, 4, KEY_Z) + MATRIX_KEY(6, 0, KEY_L) + MATRIX_KEY(6, 1, KEY_2) + MATRIX_KEY(6, 2, KEY_W) + MATRIX_KEY(6, 3, KEY_A) + MATRIX_KEY(6, 4, KEY_RIGHTBRACE) + MATRIX_KEY(7, 0, KEY_ENTER) + MATRIX_KEY(7, 1, KEY_1) + MATRIX_KEY(7, 2, KEY_Q) + MATRIX_KEY(7, 3, KEY_LEFTSHIFT) + MATRIX_KEY(7, 4, KEY_LEFTBRACE ) + >; +}; + +/* backup battery charger */ +&charger { + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; + +/* MMC2 */ +&vmmc2 { + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <3150000>; +}; + +/* LCD */ +&vaux1 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; +}; + +/* USB Host PHY */ +&vaux2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +/* available on expansion connector */ +&vaux3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + +/* ADS7846 and nubs */ +&vaux4 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + +/* power audio DAC and LID sensor */ +&vsim { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; +}; + +&i2c2 { + clock-frequency = <100000>; + /* no clients so we should disable clock */ +}; + +&i2c3 { + clock-frequency = <100000>; + + bq27500@55 { + compatible = "ti,bq27500"; + reg = <0x55>; + }; + +}; + +&usb_otg_hs { + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&vmmc1>; + bus-width = <4>; + cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; /* GPIO_126 */ +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&vmmc2>; + bus-width = <4>; + cd-gpios = <&twl_gpio 1 GPIO_ACTIVE_HIGH>; + wp-gpios = <&gpio4 31 GPIO_ACTIVE_LOW>; /* GPIO_127 */ +}; + +/* bluetooth*/ +&uart1 { +}; + +/* spare (expansion connector) */ +&uart2 { +}; + +/* console (expansion connector) */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>; +}; + +&usbhshost { + port2-mode = "ehci-phy"; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */ + + nand@0,0 { + reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ + nand-bus-width = <16>; + ti,nand-ecc-opt = "sw"; + + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-off-ns = <40>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + gpmc,device-width = <2>; + + #address-cells = <1>; + #size-cells = <1>; + + /* u-boot uses mtdparts=nand:512k(xloader),1920k(uboot),128k(uboot-env),10m(boot),-(rootfs) */ + + x-loader@0 { + label = "xloader"; + reg = <0 0x80000>; + }; + + bootloaders@80000 { + label = "uboot"; + reg = <0x80000 0x1e0000>; + }; + + bootloaders_env@260000 { + label = "uboot-env"; + reg = <0x260000 0x20000>; + }; + + kernel@280000 { + label = "boot"; + reg = <0x280000 0xa00000>; + }; + + filesystem@680000 { + label = "rootfs"; + reg = <0xc80000 0>; /* 0 = MTDPART_SIZ_FULL */ + }; + }; +}; + +&mcspi1 { + tsc2046@0 { + reg = <0>; /* CS0 */ + compatible = "ti,tsc2046"; + spi-max-frequency = <1000000>; + pinctrl-names = "default"; + pinctrl-0 = <&penirq_pins>; + interrupt-parent = <&gpio3>; + interrupts = <30 0>; /* GPIO_94 */ + pendown-gpio = <&gpio3 30 0>; + vcc-supply = <&vaux4>; + + ti,x-min = /bits/ 16 <0>; + ti,x-max = /bits/ 16 <8000>; + ti,y-min = /bits/ 16 <0>; + ti,y-max = /bits/ 16 <4800>; + ti,x-plate-ohms = /bits/ 16 <40>; + ti,pressure-max = /bits/ 16 <255>; + + linux,wakeup; + }; + + lcd: lcd@1 { + reg = <1>; /* CS1 */ + compatible = "omapdss,tpo,td043mtea1"; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + label = "lcd"; + reset-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>; /* GPIO_157 */ + vcc-supply = <&vaux1>; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + }; + + +}; + +/* n/a - used as GPIOs */ +&mcbsp1 { +}; + +/* audio DAC */ +&mcbsp2 { +}; + +/* bluetooth */ +&mcbsp3 { +}; + +/* to twl4030*/ +&mcbsp4 { +}; + +&venc { + status = "ok"; + + vdda-supply = <&vdac>; + + port { + venc_out: endpoint { + remote-endpoint = <&tv_connector_in>; + ti,channels = <2>; + }; + }; +}; + +&dss { + pinctrl-names = "default"; + pinctrl-0 = < &dss_dpi_pins >; + + status = "ok"; + vdds_dsi-supply = <&vpll2>; + + port { + dpi_out: endpoint { + remote-endpoint = <&lcd_in>; + data-lines = <24>; + }; + }; +}; diff --git a/arch/arm/boot/dts/omap3-tao3530.dtsi b/arch/arm/boot/dts/omap3-tao3530.dtsi index e89820a6776e..7bd8d9a4f67f 100644 --- a/arch/arm/boot/dts/omap3-tao3530.dtsi +++ b/arch/arm/boot/dts/omap3-tao3530.dtsi @@ -8,7 +8,16 @@ */ /dts-v1/; -#include "omap34xx-hs.dtsi" +#include "omap34xx.dtsi" + +/* Secure omaps have some devices inaccessible depending on the firmware */ +&aes { + status = "disabled"; +}; + +&sham { + status = "disabled"; +}; / { cpus { @@ -45,7 +54,6 @@ /* McBSP2 is used for onboard sound, same as on beagle */ ti,mcbsp = <&mcbsp2>; - ti,codec = <&twl_audio>; }; /* Regulator to enable/switch the vcc of the Wifi module */ diff --git a/arch/arm/boot/dts/omap3-zoom3.dts b/arch/arm/boot/dts/omap3-zoom3.dts index 6644f516a42b..131448d86e67 100644 --- a/arch/arm/boot/dts/omap3-zoom3.dts +++ b/arch/arm/boot/dts/omap3-zoom3.dts @@ -195,6 +195,16 @@ cap-power-off-card; pinctrl-names = "default"; pinctrl-0 = <&mmc3_pins &mmc3_2_pins>; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1271"; + reg = <2>; + interrupt-parent = <&gpio6>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; /* gpio 162 */ + ref-clock-frequency = <26000000>; + }; }; &uart1 { diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index 3fdc84fddb70..69a40cfc1f29 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -87,6 +87,60 @@ ranges; ti,hwmods = "l3_main"; + l4_core: l4@48000000 { + compatible = "ti,omap3-l4-core", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x48000000 0x1000000>; + + scm: scm@2000 { + compatible = "ti,omap3-scm", "simple-bus"; + reg = <0x2000 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2000 0x2000>; + + omap3_pmx_core: pinmux@30 { + compatible = "ti,omap3-padconf", + "pinctrl-single"; + reg = <0x30 0x238>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0xff1f>; + }; + + scm_conf: scm_conf@270 { + compatible = "syscon"; + reg = <0x270 0x330>; + #address-cells = <1>; + #size-cells = <1>; + + scm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + scm_clockdomains: clockdomains { + }; + + omap3_pmx_wkup: pinmux@a00 { + compatible = "ti,omap3-padconf", + "pinctrl-single"; + reg = <0xa00 0x5c>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0xff1f>; + }; + }; + }; + aes: aes@480c5000 { compatible = "ti,omap3-aes"; ti,hwmods = "aes"; @@ -123,19 +177,6 @@ }; }; - scrm: scrm@48002000 { - compatible = "ti,omap3-scrm"; - reg = <0x48002000 0x2000>; - - scrm_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - scrm_clockdomains: clockdomains { - }; - }; - counter32k: counter@48320000 { compatible = "ti,omap-counter32k"; reg = <0x48320000 0x20>; @@ -161,37 +202,10 @@ dma-requests = <96>; }; - omap3_pmx_core: pinmux@48002030 { - compatible = "ti,omap3-padconf", "pinctrl-single"; - reg = <0x48002030 0x0238>; - #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - pinctrl-single,register-width = <16>; - pinctrl-single,function-mask = <0xff1f>; - }; - - omap3_pmx_wkup: pinmux@48002a00 { - compatible = "ti,omap3-padconf", "pinctrl-single"; - reg = <0x48002a00 0x5c>; - #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - pinctrl-single,register-width = <16>; - pinctrl-single,function-mask = <0xff1f>; - }; - - omap3_scm_general: tisyscon@48002270 { - compatible = "syscon"; - reg = <0x48002270 0x2f0>; - }; - pbias_regulator: pbias_regulator { compatible = "ti,pbias-omap"; reg = <0x2b0 0x4>; - syscon = <&omap3_scm_general>; + syscon = <&scm_conf>; pbias_mmc_reg: pbias_mmc_omap2430 { regulator-name = "pbias_mmc_omap2430"; regulator-min-microvolt = <1800000>; @@ -442,6 +456,7 @@ }; mmu_isp: mmu@480bd400 { + #iommu-cells = <0>; compatible = "ti,omap2-iommu"; reg = <0x480bd400 0x80>; interrupts = <24>; @@ -450,6 +465,7 @@ }; mmu_iva: mmu@5d000000 { + #iommu-cells = <0>; compatible = "ti,omap2-iommu"; reg = <0x5d000000 0x80>; interrupts = <28>; diff --git a/arch/arm/boot/dts/omap34xx-hs.dtsi b/arch/arm/boot/dts/omap34xx-hs.dtsi deleted file mode 100644 index 1ff626489546..000000000000 --- a/arch/arm/boot/dts/omap34xx-hs.dtsi +++ /dev/null @@ -1,16 +0,0 @@ -/* Disabled modules for secure omaps */ - -#include "omap34xx.dtsi" - -/* Secure omaps have some devices inaccessible depending on the firmware */ -&aes { - status = "disabled"; -}; - -&sham { - status = "disabled"; -}; - -&timer12 { - status = "disabled"; -}; diff --git a/arch/arm/boot/dts/omap34xx.dtsi b/arch/arm/boot/dts/omap34xx.dtsi index 3819c1e91591..4f6b2d5b1902 100644 --- a/arch/arm/boot/dts/omap34xx.dtsi +++ b/arch/arm/boot/dts/omap34xx.dtsi @@ -8,6 +8,8 @@ * kind, whether express or implied. */ +#include + #include "omap3.dtsi" / { @@ -37,6 +39,21 @@ pinctrl-single,register-width = <16>; pinctrl-single,function-mask = <0xff1f>; }; + + isp: isp@480bc000 { + compatible = "ti,omap3-isp"; + reg = <0x480bc000 0x12fc + 0x480bd800 0x017c>; + interrupts = <24>; + iommus = <&mmu_isp>; + syscon = <&scm_conf 0xdc>; + ti,phy-type = ; + #clock-cells = <1>; + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; }; }; diff --git a/arch/arm/boot/dts/omap36xx-hs.dtsi b/arch/arm/boot/dts/omap36xx-hs.dtsi deleted file mode 100644 index 2c7febb0e016..000000000000 --- a/arch/arm/boot/dts/omap36xx-hs.dtsi +++ /dev/null @@ -1,16 +0,0 @@ -/* Disabled modules for secure omaps */ - -#include "omap36xx.dtsi" - -/* Secure omaps have some devices inaccessible depending on the firmware */ -&aes { - status = "disabled"; -}; - -&sham { - status = "disabled"; -}; - -&timer12 { - status = "disabled"; -}; diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi index 541704a59a5a..86253de5a97a 100644 --- a/arch/arm/boot/dts/omap36xx.dtsi +++ b/arch/arm/boot/dts/omap36xx.dtsi @@ -8,6 +8,8 @@ * kind, whether express or implied. */ +#include + #include "omap3.dtsi" / { @@ -69,6 +71,21 @@ pinctrl-single,register-width = <16>; pinctrl-single,function-mask = <0xff1f>; }; + + isp: isp@480bc000 { + compatible = "ti,omap3-isp"; + reg = <0x480bc000 0x12fc + 0x480bd800 0x0600>; + interrupts = <24>; + iommus = <&mmu_isp>; + syscon = <&scm_conf 0x2f0>; + ti,phy-type = ; + #clock-cells = <1>; + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; }; }; diff --git a/arch/arm/boot/dts/omap3xxx-clocks.dtsi b/arch/arm/boot/dts/omap3xxx-clocks.dtsi index 5c375003bad1..bbba5bdc4bc9 100644 --- a/arch/arm/boot/dts/omap3xxx-clocks.dtsi +++ b/arch/arm/boot/dts/omap3xxx-clocks.dtsi @@ -79,13 +79,14 @@ clock-div = <1>; }; }; -&scrm_clocks { + +&scm_clocks { mcbsp5_mux_fck: mcbsp5_mux_fck { #clock-cells = <0>; compatible = "ti,composite-mux-clock"; clocks = <&core_96m_fck>, <&mcbsp_clks>; ti,bit-shift = <4>; - reg = <0x02d8>; + reg = <0x68>; }; mcbsp5_fck: mcbsp5_fck { @@ -99,7 +100,7 @@ compatible = "ti,composite-mux-clock"; clocks = <&core_96m_fck>, <&mcbsp_clks>; ti,bit-shift = <2>; - reg = <0x0274>; + reg = <0x04>; }; mcbsp1_fck: mcbsp1_fck { @@ -113,7 +114,7 @@ compatible = "ti,composite-mux-clock"; clocks = <&per_96m_fck>, <&mcbsp_clks>; ti,bit-shift = <6>; - reg = <0x0274>; + reg = <0x04>; }; mcbsp2_fck: mcbsp2_fck { @@ -126,7 +127,7 @@ #clock-cells = <0>; compatible = "ti,composite-mux-clock"; clocks = <&per_96m_fck>, <&mcbsp_clks>; - reg = <0x02d8>; + reg = <0x68>; }; mcbsp3_fck: mcbsp3_fck { @@ -140,7 +141,7 @@ compatible = "ti,composite-mux-clock"; clocks = <&per_96m_fck>, <&mcbsp_clks>; ti,bit-shift = <2>; - reg = <0x02d8>; + reg = <0x68>; }; mcbsp4_fck: mcbsp4_fck { diff --git a/arch/arm/boot/dts/omap4-cpu-thermal.dtsi b/arch/arm/boot/dts/omap4-cpu-thermal.dtsi index cb9458feb2e3..ab7f87ae96f0 100644 --- a/arch/arm/boot/dts/omap4-cpu-thermal.dtsi +++ b/arch/arm/boot/dts/omap4-cpu-thermal.dtsi @@ -18,7 +18,7 @@ cpu_thermal: cpu_thermal { /* sensor ID */ thermal-sensors = <&bandgap 0>; - trips { + cpu_trips: trips { cpu_alert0: cpu_alert { temperature = <100000>; /* millicelsius */ hysteresis = <2000>; /* millicelsius */ @@ -31,7 +31,7 @@ cpu_thermal: cpu_thermal { }; }; - cooling-maps { + cpu_cooling_maps: cooling-maps { map0 { trip = <&cpu_alert0>; cooling-device = diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 7c15fb2e2fe4..f1507bc8737e 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -448,6 +448,16 @@ non-removable; bus-width = <4>; cap-power-off-card; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1271"; + reg = <2>; + interrupt-parent = <&gpio2>; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* gpio 53 */ + ref-clock-frequency = <38400000>; + }; }; &emif1 { diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index 8aca8dae968a..dac86ed7481f 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -485,6 +485,17 @@ non-removable; bus-width = <4>; cap-power-off-card; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1281"; + reg = <2>; + interrupt-parent = <&gpio1>; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* gpio 53 */ + ref-clock-frequency = <26000000>; + tcxo-clock-frequency = <26000000>; + }; }; &emif1 { diff --git a/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi b/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi index cc66af419236..9bceeb7e1f03 100644 --- a/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi +++ b/arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi @@ -65,4 +65,14 @@ bus-width = <4>; cap-power-off-card; status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1271"; + reg = <2>; + interrupt-parent = <&gpio2>; + interrupts = <9 IRQ_TYPE_LEVEL_HIGH>; /* gpio 41 */ + ref-clock-frequency = <38400000>; + }; }; diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index f2091d1c9c36..f884d6adb71e 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -124,99 +124,141 @@ interrupts = , ; - cm1: cm1@4a004000 { - compatible = "ti,omap4-cm1"; - reg = <0x4a004000 0x2000>; - - cm1_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - cm1_clockdomains: clockdomains { - }; - }; - - prm: prm@4a306000 { - compatible = "ti,omap4-prm"; - reg = <0x4a306000 0x3000>; - interrupts = ; - - prm_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - prm_clockdomains: clockdomains { - }; - }; - - cm2: cm2@4a008000 { - compatible = "ti,omap4-cm2"; - reg = <0x4a008000 0x3000>; - - cm2_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - cm2_clockdomains: clockdomains { - }; - }; - - scrm: scrm@4a30a000 { - compatible = "ti,omap4-scrm"; - reg = <0x4a30a000 0x2000>; - - scrm_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - scrm_clockdomains: clockdomains { - }; - }; - - counter32k: counter@4a304000 { - compatible = "ti,omap-counter32k"; - reg = <0x4a304000 0x20>; - ti,hwmods = "counter_32k"; - }; - - omap4_pmx_core: pinmux@4a100040 { - compatible = "ti,omap4-padconf", "pinctrl-single"; - reg = <0x4a100040 0x0196>; + l4_cfg: l4@4a000000 { + compatible = "ti,omap4-l4-cfg", "simple-bus"; #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - pinctrl-single,register-width = <16>; - pinctrl-single,function-mask = <0x7fff>; - }; - omap4_pmx_wkup: pinmux@4a31e040 { - compatible = "ti,omap4-padconf", "pinctrl-single"; - reg = <0x4a31e040 0x0038>; - #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - pinctrl-single,register-width = <16>; - pinctrl-single,function-mask = <0x7fff>; - }; + #size-cells = <1>; + ranges = <0 0x4a000000 0x1000000>; - omap4_padconf_global: tisyscon@4a1005a0 { - compatible = "syscon"; - reg = <0x4a1005a0 0x170>; - }; + cm1: cm1@4000 { + compatible = "ti,omap4-cm1"; + reg = <0x4000 0x2000>; - pbias_regulator: pbias_regulator { - compatible = "ti,pbias-omap"; - reg = <0x60 0x4>; - syscon = <&omap4_padconf_global>; - pbias_mmc_reg: pbias_mmc_omap4 { - regulator-name = "pbias_mmc_omap4"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3000000>; + cm1_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + cm1_clockdomains: clockdomains { + }; + }; + + cm2: cm2@8000 { + compatible = "ti,omap4-cm2"; + reg = <0x8000 0x3000>; + + cm2_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + cm2_clockdomains: clockdomains { + }; + }; + + omap4_scm_core: scm@2000 { + compatible = "ti,omap4-scm-core", "simple-bus"; + reg = <0x2000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2000 0x1000>; + + scm_conf: scm_conf@0 { + compatible = "syscon"; + reg = <0x0 0x800>; + #address-cells = <1>; + #size-cells = <1>; + }; + }; + + omap4_padconf_core: scm@100000 { + compatible = "ti,omap4-scm-padconf-core", + "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x100000 0x1000>; + + omap4_pmx_core: pinmux@40 { + compatible = "ti,omap4-padconf", + "pinctrl-single"; + reg = <0x40 0x0196>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0x7fff>; + }; + + omap4_padconf_global: omap4_padconf_global@5a0 { + compatible = "syscon"; + reg = <0x5a0 0x170>; + #address-cells = <1>; + #size-cells = <1>; + + pbias_regulator: pbias_regulator { + compatible = "ti,pbias-omap"; + reg = <0x60 0x4>; + syscon = <&omap4_padconf_global>; + pbias_mmc_reg: pbias_mmc_omap4 { + regulator-name = "pbias_mmc_omap4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; + }; + }; + }; + + l4_wkup: l4@300000 { + compatible = "ti,omap4-l4-wkup", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x300000 0x40000>; + + counter32k: counter@4000 { + compatible = "ti,omap-counter32k"; + reg = <0x4000 0x20>; + ti,hwmods = "counter_32k"; + }; + + prm: prm@6000 { + compatible = "ti,omap4-prm"; + reg = <0x6000 0x3000>; + interrupts = ; + + prm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + prm_clockdomains: clockdomains { + }; + }; + + scrm: scrm@a000 { + compatible = "ti,omap4-scrm"; + reg = <0xa000 0x2000>; + + scrm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + scrm_clockdomains: clockdomains { + }; + }; + + omap4_pmx_wkup: pinmux@1e040 { + compatible = "ti,omap4-padconf", + "pinctrl-single"; + reg = <0x1e040 0x0038>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0x7fff>; + }; }; }; diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index 77b5f70d0ebc..7d24ae0306b5 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -128,7 +128,7 @@ * hierarchy. */ ocp { - compatible = "ti,omap4-l3-noc", "simple-bus"; + compatible = "ti,omap5-l3-noc", "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges; @@ -139,99 +139,141 @@ interrupts = , ; - prm: prm@4ae06000 { - compatible = "ti,omap5-prm"; - reg = <0x4ae06000 0x3000>; - interrupts = ; - - prm_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - prm_clockdomains: clockdomains { - }; - }; - - cm_core_aon: cm_core_aon@4a004000 { - compatible = "ti,omap5-cm-core-aon"; - reg = <0x4a004000 0x2000>; - - cm_core_aon_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - cm_core_aon_clockdomains: clockdomains { - }; - }; - - scrm: scrm@4ae0a000 { - compatible = "ti,omap5-scrm"; - reg = <0x4ae0a000 0x2000>; - - scrm_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - scrm_clockdomains: clockdomains { - }; - }; - - cm_core: cm_core@4a008000 { - compatible = "ti,omap5-cm-core"; - reg = <0x4a008000 0x3000>; - - cm_core_clocks: clocks { - #address-cells = <1>; - #size-cells = <0>; - }; - - cm_core_clockdomains: clockdomains { - }; - }; - - counter32k: counter@4ae04000 { - compatible = "ti,omap-counter32k"; - reg = <0x4ae04000 0x40>; - ti,hwmods = "counter_32k"; - }; - - omap5_pmx_core: pinmux@4a002840 { - compatible = "ti,omap5-padconf", "pinctrl-single"; - reg = <0x4a002840 0x01b6>; + l4_cfg: l4@4a000000 { + compatible = "ti,omap5-l4-cfg", "simple-bus"; #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - pinctrl-single,register-width = <16>; - pinctrl-single,function-mask = <0x7fff>; + #size-cells = <1>; + ranges = <0 0x4a000000 0x22a000>; + + scm_core: scm@2000 { + compatible = "ti,omap5-scm-core", "simple-bus"; + reg = <0x2000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2000 0x800>; + + scm_conf: scm_conf@0 { + compatible = "syscon"; + reg = <0x0 0x800>; + #address-cells = <1>; + #size-cells = <1>; + }; + }; + + scm_padconf_core: scm@2800 { + compatible = "ti,omap5-scm-padconf-core", + "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2800 0x800>; + + omap5_pmx_core: pinmux@40 { + compatible = "ti,omap5-padconf", + "pinctrl-single"; + reg = <0x40 0x01b6>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0x7fff>; + }; + + omap5_padconf_global: omap5_padconf_global@5a0 { + compatible = "syscon"; + reg = <0x5a0 0xec>; + #address-cells = <1>; + #size-cells = <1>; + + pbias_regulator: pbias_regulator { + compatible = "ti,pbias-omap"; + reg = <0x60 0x4>; + syscon = <&omap5_padconf_global>; + pbias_mmc_reg: pbias_mmc_omap5 { + regulator-name = "pbias_mmc_omap5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; + }; + }; + }; + + cm_core_aon: cm_core_aon@4000 { + compatible = "ti,omap5-cm-core-aon"; + reg = <0x4000 0x2000>; + + cm_core_aon_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + cm_core_aon_clockdomains: clockdomains { + }; + }; + + cm_core: cm_core@8000 { + compatible = "ti,omap5-cm-core"; + reg = <0x8000 0x3000>; + + cm_core_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + cm_core_clockdomains: clockdomains { + }; + }; }; - omap5_pmx_wkup: pinmux@4ae0c840 { - compatible = "ti,omap5-padconf", "pinctrl-single"; - reg = <0x4ae0c840 0x0038>; + + l4_wkup: l4@4ae00000 { + compatible = "ti,omap5-l4-wkup", "simple-bus"; #address-cells = <1>; - #size-cells = <0>; - #interrupt-cells = <1>; - interrupt-controller; - pinctrl-single,register-width = <16>; - pinctrl-single,function-mask = <0x7fff>; - }; + #size-cells = <1>; + ranges = <0 0x4ae00000 0x2b000>; - omap5_padconf_global: tisyscon@4a002da0 { - compatible = "syscon"; - reg = <0x4A002da0 0xec>; - }; + counter32k: counter@4000 { + compatible = "ti,omap-counter32k"; + reg = <0x4000 0x40>; + ti,hwmods = "counter_32k"; + }; - pbias_regulator: pbias_regulator { - compatible = "ti,pbias-omap"; - reg = <0x60 0x4>; - syscon = <&omap5_padconf_global>; - pbias_mmc_reg: pbias_mmc_omap5 { - regulator-name = "pbias_mmc_omap5"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3000000>; + prm: prm@6000 { + compatible = "ti,omap5-prm"; + reg = <0x6000 0x3000>; + interrupts = ; + + prm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + prm_clockdomains: clockdomains { + }; + }; + + scrm: scrm@a000 { + compatible = "ti,omap5-scrm"; + reg = <0xa000 0x2000>; + + scrm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + scrm_clockdomains: clockdomains { + }; + }; + + omap5_pmx_wkup: pinmux@c840 { + compatible = "ti,omap5-padconf", + "pinctrl-single"; + reg = <0xc840 0x0038>; + #address-cells = <1>; + #size-cells = <0>; + #interrupt-cells = <1>; + interrupt-controller; + pinctrl-single,register-width = <16>; + pinctrl-single,function-mask = <0x7fff>; }; }; diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index b3154c071652..6c1511263a55 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -23,6 +23,7 @@ next-level-cache = <&L2>; qcom,acc = <&acc0>; qcom,saw = <&saw0>; + cpu-idle-states = <&CPU_SPC>; }; cpu@1 { @@ -33,6 +34,7 @@ next-level-cache = <&L2>; qcom,acc = <&acc1>; qcom,saw = <&saw1>; + cpu-idle-states = <&CPU_SPC>; }; cpu@2 { @@ -43,6 +45,7 @@ next-level-cache = <&L2>; qcom,acc = <&acc2>; qcom,saw = <&saw2>; + cpu-idle-states = <&CPU_SPC>; }; cpu@3 { @@ -53,12 +56,23 @@ next-level-cache = <&L2>; qcom,acc = <&acc3>; qcom,saw = <&saw3>; + cpu-idle-states = <&CPU_SPC>; }; L2: l2-cache { compatible = "cache"; cache-level = <2>; }; + + idle-states { + CPU_SPC: spc { + compatible = "qcom,idle-state-spc", + "arm,idle-state"; + entry-latency-us = <400>; + exit-latency-us = <900>; + min-residency-us = <3000>; + }; + }; }; cpu-pmu { @@ -139,26 +153,26 @@ reg = <0x020b8000 0x1000>, <0x02008000 0x1000>; }; - saw0: regulator@2089000 { - compatible = "qcom,saw2"; + saw0: power-controller@2089000 { + compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2"; reg = <0x02089000 0x1000>, <0x02009000 0x1000>; regulator; }; - saw1: regulator@2099000 { - compatible = "qcom,saw2"; + saw1: power-controller@2099000 { + compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2"; reg = <0x02099000 0x1000>, <0x02009000 0x1000>; regulator; }; - saw2: regulator@20a9000 { - compatible = "qcom,saw2"; + saw2: power-controller@20a9000 { + compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2"; reg = <0x020a9000 0x1000>, <0x02009000 0x1000>; regulator; }; - saw3: regulator@20b9000 { - compatible = "qcom,saw2"; + saw3: power-controller@20b9000 { + compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2"; reg = <0x020b9000 0x1000>, <0x02009000 0x1000>; regulator; }; @@ -166,6 +180,7 @@ gsbi1: gsbi@12440000 { status = "disabled"; compatible = "qcom,gsbi-v1.0.0"; + cell-index = <1>; reg = <0x12440000 0x100>; clocks = <&gcc GSBI1_H_CLK>; clock-names = "iface"; @@ -173,6 +188,8 @@ #size-cells = <1>; ranges; + syscon-tcsr = <&tcsr>; + i2c1: i2c@12460000 { compatible = "qcom,i2c-qup-v1.1.1"; reg = <0x12460000 0x1000>; @@ -187,6 +204,7 @@ gsbi2: gsbi@12480000 { status = "disabled"; compatible = "qcom,gsbi-v1.0.0"; + cell-index = <2>; reg = <0x12480000 0x100>; clocks = <&gcc GSBI2_H_CLK>; clock-names = "iface"; @@ -194,6 +212,8 @@ #size-cells = <1>; ranges; + syscon-tcsr = <&tcsr>; + i2c2: i2c@124a0000 { compatible = "qcom,i2c-qup-v1.1.1"; reg = <0x124a0000 0x1000>; @@ -208,6 +228,7 @@ gsbi7: gsbi@16600000 { status = "disabled"; compatible = "qcom,gsbi-v1.0.0"; + cell-index = <7>; reg = <0x16600000 0x100>; clocks = <&gcc GSBI7_H_CLK>; clock-names = "iface"; @@ -215,6 +236,8 @@ #size-cells = <1>; ranges; + syscon-tcsr = <&tcsr>; + serial@16640000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x16640000 0x1000>, @@ -239,6 +262,13 @@ #reset-cells = <1>; }; + lcc: clock-controller@28000000 { + compatible = "qcom,lcc-apq8064"; + reg = <0x28000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + mmcc: clock-controller@4000000 { compatible = "qcom,mmcc-apq8064"; reg = <0x4000000 0x1000>; @@ -349,5 +379,10 @@ pinctrl-0 = <&sdc4_gpios>; }; }; + + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-apq8064", "syscon"; + reg = <0x1a400000 0x100>; + }; }; }; diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts index 47370494d0f8..d484d08163e9 100644 --- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts +++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts @@ -1,4 +1,6 @@ #include "qcom-msm8974.dtsi" +#include "qcom-pm8841.dtsi" +#include "qcom-pm8941.dtsi" / { model = "Qualcomm APQ8074 Dragonboard"; diff --git a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts b/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts index c9ff10821ad9..f7725b96612c 100644 --- a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts +++ b/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts @@ -1,4 +1,5 @@ #include "qcom-apq8084.dtsi" +#include "qcom-pma8084.dtsi" / { model = "Qualcomm APQ8084/IFC6540"; diff --git a/arch/arm/boot/dts/qcom-apq8084-mtp.dts b/arch/arm/boot/dts/qcom-apq8084-mtp.dts index 8ecec58a9ff6..cb43acfc5d1d 100644 --- a/arch/arm/boot/dts/qcom-apq8084-mtp.dts +++ b/arch/arm/boot/dts/qcom-apq8084-mtp.dts @@ -1,4 +1,5 @@ #include "qcom-apq8084.dtsi" +#include "qcom-pma8084.dtsi" / { model = "Qualcomm APQ 8084-MTP"; diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi index 1f130bc16858..7084010ee61b 100644 --- a/arch/arm/boot/dts/qcom-apq8084.dtsi +++ b/arch/arm/boot/dts/qcom-apq8084.dtsi @@ -21,6 +21,8 @@ enable-method = "qcom,kpss-acc-v2"; next-level-cache = <&L2>; qcom,acc = <&acc0>; + qcom,saw = <&saw0>; + cpu-idle-states = <&CPU_SPC>; }; cpu@1 { @@ -30,6 +32,8 @@ enable-method = "qcom,kpss-acc-v2"; next-level-cache = <&L2>; qcom,acc = <&acc1>; + qcom,saw = <&saw1>; + cpu-idle-states = <&CPU_SPC>; }; cpu@2 { @@ -39,6 +43,8 @@ enable-method = "qcom,kpss-acc-v2"; next-level-cache = <&L2>; qcom,acc = <&acc2>; + qcom,saw = <&saw2>; + cpu-idle-states = <&CPU_SPC>; }; cpu@3 { @@ -48,6 +54,8 @@ enable-method = "qcom,kpss-acc-v2"; next-level-cache = <&L2>; qcom,acc = <&acc3>; + qcom,saw = <&saw3>; + cpu-idle-states = <&CPU_SPC>; }; L2: l2-cache { @@ -55,6 +63,16 @@ cache-level = <2>; qcom,saw = <&saw_l2>; }; + + idle-states { + CPU_SPC: spc { + compatible = "qcom,idle-state-spc", + "arm,idle-state"; + entry-latency-us = <150>; + exit-latency-us = <200>; + min-residency-us = <2000>; + }; + }; }; cpu-pmu { @@ -144,7 +162,27 @@ }; }; - saw_l2: regulator@f9012000 { + saw0: power-controller@f9089000 { + compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2"; + reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>; + }; + + saw1: power-controller@f9099000 { + compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2"; + reg = <0xf9099000 0x1000>, <0xf9009000 0x1000>; + }; + + saw2: power-controller@f90a9000 { + compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2"; + reg = <0xf90a9000 0x1000>, <0xf9009000 0x1000>; + }; + + saw3: power-controller@f90b9000 { + compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2"; + reg = <0xf90b9000 0x1000>, <0xf9009000 0x1000>; + }; + + saw_l2: power-controller@f9012000 { compatible = "qcom,saw2"; reg = <0xf9012000 0x1000>; regulator; @@ -226,5 +264,21 @@ clock-names = "core", "iface"; status = "disabled"; }; + + spmi_bus: spmi@fc4cf000 { + compatible = "qcom,spmi-pmic-arb"; + reg-names = "core", "intr", "cnfg"; + reg = <0xfc4cf000 0x1000>, + <0xfc4cb000 0x1000>, + <0xfc4ca000 0x1000>; + interrupt-names = "periph_irq"; + interrupts = <0 190 0>; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + }; }; }; diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi index cb225dafe97c..9f727d8eadf6 100644 --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi @@ -2,6 +2,7 @@ #include "skeleton.dtsi" #include +#include #include / { @@ -60,12 +61,35 @@ }; }; + clocks { + sleep_clk: sleep_clk { + compatible = "fixed-clock"; + clock-frequency = <32768>; + #clock-cells = <0>; + }; + }; + soc: soc { #address-cells = <1>; #size-cells = <1>; ranges; compatible = "simple-bus"; + lpass@28100000 { + compatible = "qcom,lpass-cpu"; + status = "disabled"; + clocks = <&lcc AHBIX_CLK>, + <&lcc MI2S_OSR_CLK>, + <&lcc MI2S_BIT_CLK>; + clock-names = "ahbix-clk", + "mi2s-osr-clk", + "mi2s-bit-clk"; + interrupts = <0 85 1>; + interrupt-names = "lpass-irq-lpaif"; + reg = <0x28100000 0x10000>; + reg-names = "lpass-lpaif"; + }; + qcom_pinmux: pinmux@800000 { compatible = "qcom,ipq8064-pinctrl"; reg = <0x800000 0x4000>; @@ -89,10 +113,14 @@ compatible = "qcom,kpss-timer", "qcom,msm-timer"; interrupts = <1 1 0x301>, <1 2 0x301>, - <1 3 0x301>; + <1 3 0x301>, + <1 4 0x301>, + <1 5 0x301>; reg = <0x0200a000 0x100>; clock-frequency = <25000000>, <32768>; + clocks = <&sleep_clk>; + clock-names = "sleep"; cpu-offset = <0x80000>; }; @@ -120,6 +148,7 @@ gsbi2: gsbi@12480000 { compatible = "qcom,gsbi-v1.0.0"; + cell-index = <2>; reg = <0x12480000 0x100>; clocks = <&gcc GSBI2_H_CLK>; clock-names = "iface"; @@ -128,6 +157,8 @@ ranges; status = "disabled"; + syscon-tcsr = <&tcsr>; + serial@12490000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x12490000 0x1000>, @@ -155,6 +186,7 @@ gsbi4: gsbi@16300000 { compatible = "qcom,gsbi-v1.0.0"; + cell-index = <4>; reg = <0x16300000 0x100>; clocks = <&gcc GSBI4_H_CLK>; clock-names = "iface"; @@ -163,6 +195,8 @@ ranges; status = "disabled"; + syscon-tcsr = <&tcsr>; + serial@16340000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x16340000 0x1000>, @@ -189,6 +223,7 @@ gsbi5: gsbi@1a200000 { compatible = "qcom,gsbi-v1.0.0"; + cell-index = <5>; reg = <0x1a200000 0x100>; clocks = <&gcc GSBI5_H_CLK>; clock-names = "iface"; @@ -197,6 +232,8 @@ ranges; status = "disabled"; + syscon-tcsr = <&tcsr>; + serial@1a240000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x1a240000 0x1000>, @@ -279,5 +316,18 @@ #clock-cells = <1>; #reset-cells = <1>; }; + + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-ipq8064", "syscon"; + reg = <0x1a400000 0x100>; + }; + + lcc: clock-controller@28000000 { + compatible = "qcom,lcc-ipq8064"; + reg = <0x28000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + }; }; diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi index 0affd6193f56..20bbd19b996e 100644 --- a/arch/arm/boot/dts/qcom-msm8660.dtsi +++ b/arch/arm/boot/dts/qcom-msm8660.dtsi @@ -82,6 +82,7 @@ gsbi12: gsbi@19c00000 { compatible = "qcom,gsbi-v1.0.0"; + cell-index = <12>; reg = <0x19c00000 0x100>; clocks = <&gcc GSBI12_H_CLK>; clock-names = "iface"; @@ -89,6 +90,8 @@ #size-cells = <1>; ranges; + syscon-tcsr = <&tcsr>; + serial@19c40000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x19c40000 0x1000>, @@ -196,6 +199,11 @@ vmmc-supply = <&vsdcc_fixed>; }; }; + + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-msm8660", "syscon"; + reg = <0x1a400000 0x100>; + }; }; }; diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi index e1b0d5cd9e3c..a02b984cc68d 100644 --- a/arch/arm/boot/dts/qcom-msm8960.dtsi +++ b/arch/arm/boot/dts/qcom-msm8960.dtsi @@ -91,6 +91,13 @@ reg = <0x900000 0x4000>; }; + lcc: clock-controller@28000000 { + compatible = "qcom,lcc-msm8960"; + reg = <0x28000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + clock-controller@4000000 { compatible = "qcom,mmcc-msm8960"; reg = <0x4000000 0x1000>; @@ -122,6 +129,7 @@ gsbi5: gsbi@16400000 { compatible = "qcom,gsbi-v1.0.0"; + cell-index = <5>; reg = <0x16400000 0x100>; clocks = <&gcc GSBI5_H_CLK>; clock-names = "iface"; @@ -129,6 +137,8 @@ #size-cells = <1>; ranges; + syscon-tcsr = <&tcsr>; + serial@16440000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x16440000 0x1000>, @@ -238,5 +248,10 @@ vmmc-supply = <&vsdcc_fixed>; }; }; + + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-msm8960", "syscon"; + reg = <0x1a400000 0x100>; + }; }; }; diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts index cccc21b7c8fd..bd35b0674ff6 100644 --- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts +++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts @@ -1,4 +1,6 @@ #include "qcom-msm8974.dtsi" +#include "qcom-pm8841.dtsi" +#include "qcom-pm8941.dtsi" / { model = "Sony Xperia Z1"; diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi index e265ec16a787..37b47b5538b8 100644 --- a/arch/arm/boot/dts/qcom-msm8974.dtsi +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi @@ -21,6 +21,8 @@ reg = <0>; next-level-cache = <&L2>; qcom,acc = <&acc0>; + qcom,saw = <&saw0>; + cpu-idle-states = <&CPU_SPC>; }; cpu@1 { @@ -30,6 +32,8 @@ reg = <1>; next-level-cache = <&L2>; qcom,acc = <&acc1>; + qcom,saw = <&saw1>; + cpu-idle-states = <&CPU_SPC>; }; cpu@2 { @@ -39,6 +43,8 @@ reg = <2>; next-level-cache = <&L2>; qcom,acc = <&acc2>; + qcom,saw = <&saw2>; + cpu-idle-states = <&CPU_SPC>; }; cpu@3 { @@ -48,6 +54,8 @@ reg = <3>; next-level-cache = <&L2>; qcom,acc = <&acc3>; + qcom,saw = <&saw3>; + cpu-idle-states = <&CPU_SPC>; }; L2: l2-cache { @@ -55,6 +63,16 @@ cache-level = <2>; qcom,saw = <&saw_l2>; }; + + idle-states { + CPU_SPC: spc { + compatible = "qcom,idle-state-spc", + "arm,idle-state"; + entry-latency-us = <150>; + exit-latency-us = <200>; + min-residency-us = <2000>; + }; + }; }; cpu-pmu { @@ -144,7 +162,27 @@ }; }; - saw_l2: regulator@f9012000 { + saw0: power-controller@f9089000 { + compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2"; + reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>; + }; + + saw1: power-controller@f9099000 { + compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2"; + reg = <0xf9099000 0x1000>, <0xf9009000 0x1000>; + }; + + saw2: power-controller@f90a9000 { + compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2"; + reg = <0xf90a9000 0x1000>, <0xf9009000 0x1000>; + }; + + saw3: power-controller@f90b9000 { + compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2"; + reg = <0xf90b9000 0x1000>, <0xf9009000 0x1000>; + }; + + saw_l2: power-controller@f9012000 { compatible = "qcom,saw2"; reg = <0xf9012000 0x1000>; regulator; @@ -247,5 +285,21 @@ #address-cells = <1>; #size-cells = <0>; }; + + spmi_bus: spmi@fc4cf000 { + compatible = "qcom,spmi-pmic-arb"; + reg-names = "core", "intr", "cnfg"; + reg = <0xfc4cf000 0x1000>, + <0xfc4cb000 0x1000>, + <0xfc4ca000 0x1000>; + interrupt-names = "periph_irq"; + interrupts = <0 190 0>; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + }; }; }; diff --git a/arch/arm/boot/dts/qcom-pm8841.dtsi b/arch/arm/boot/dts/qcom-pm8841.dtsi new file mode 100644 index 000000000000..73813cc118f9 --- /dev/null +++ b/arch/arm/boot/dts/qcom-pm8841.dtsi @@ -0,0 +1,18 @@ +#include + +&spmi_bus { + + usid4: pm8841@4 { + compatible = "qcom,spmi-pmic"; + reg = <0x4 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; + + usid5: pm8841@5 { + compatible = "qcom,spmi-pmic"; + reg = <0x5 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; +}; diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi new file mode 100644 index 000000000000..24c5088acea2 --- /dev/null +++ b/arch/arm/boot/dts/qcom-pm8941.dtsi @@ -0,0 +1,18 @@ +#include + +&spmi_bus { + + usid0: pm8941@0 { + compatible ="qcom,spmi-pmic"; + reg = <0x0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; + + usid1: pm8941@1 { + compatible ="qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; +}; diff --git a/arch/arm/boot/dts/qcom-pma8084.dtsi b/arch/arm/boot/dts/qcom-pma8084.dtsi new file mode 100644 index 000000000000..a5a4fe695a46 --- /dev/null +++ b/arch/arm/boot/dts/qcom-pma8084.dtsi @@ -0,0 +1,18 @@ +#include + +&spmi_bus { + + usid0: pma8084@0 { + compatible = "qcom,spmi-pmic"; + reg = <0x0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; + + usid1: pma8084@1 { + compatible = "qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; +}; diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm-reference.dts b/arch/arm/boot/dts/r8a73a4-ape6evm-reference.dts deleted file mode 100644 index b3d8f844b57a..000000000000 --- a/arch/arm/boot/dts/r8a73a4-ape6evm-reference.dts +++ /dev/null @@ -1,156 +0,0 @@ -/* - * Device Tree Source for the APE6EVM board - * - * Copyright (C) 2013 Renesas Solutions Corp. - * - * This file is licensed under the terms of the GNU General Public License - * version 2. This program is licensed "as is" without any warranty of any - * kind, whether express or implied. - */ - -/dts-v1/; -#include "r8a73a4.dtsi" -#include - -/ { - model = "APE6EVM"; - compatible = "renesas,ape6evm-reference", "renesas,r8a73a4"; - - aliases { - serial0 = &scifa0; - }; - - chosen { - bootargs = "ignore_loglevel rw"; - stdout-path = &scifa0; - }; - - memory@40000000 { - device_type = "memory"; - reg = <0 0x40000000 0 0x40000000>; - }; - - memory@200000000 { - device_type = "memory"; - reg = <2 0x00000000 0 0x40000000>; - }; - - vcc_mmc0: regulator@0 { - compatible = "regulator-fixed"; - regulator-name = "MMC0 Vcc"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - regulator-always-on; - }; - - vcc_sdhi0: regulator@1 { - compatible = "regulator-fixed"; - - regulator-name = "SDHI0 Vcc"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - - gpio = <&pfc 76 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - /* Common 3.3V rail, used by several devices on APE6EVM */ - ape6evm_fixed_3v3: regulator@2 { - compatible = "regulator-fixed"; - regulator-name = "3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - lbsc { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0 0 0x20000000>; - }; -}; - -&i2c5 { - status = "okay"; - vdd_dvfs: max8973@1b { - compatible = "maxim,max8973"; - reg = <0x1b>; - - regulator-min-microvolt = <935000>; - regulator-max-microvolt = <1200000>; - regulator-boot-on; - regulator-always-on; - }; -}; - -&cpu0 { - cpu0-supply = <&vdd_dvfs>; - operating-points = < - /* kHz uV */ - 1950000 1115000 - 1462500 995000 - >; - voltage-tolerance = <1>; /* 1% */ -}; - -&cmt1 { - status = "okay"; -}; - -&pfc { - scifa0_pins: serial0 { - renesas,groups = "scifa0_data"; - renesas,function = "scifa0"; - }; - - mmc0_pins: mmc { - renesas,groups = "mmc0_data8", "mmc0_ctrl"; - renesas,function = "mmc0"; - }; - - sdhi0_pins: sd0 { - renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_cd"; - renesas,function = "sdhi0"; - }; - - sdhi1_pins: sd1 { - renesas,groups = "sdhi1_data4", "sdhi1_ctrl"; - renesas,function = "sdhi1"; - }; -}; - -&mmcif0 { - vmmc-supply = <&vcc_mmc0>; - bus-width = <8>; - non-removable; - pinctrl-names = "default"; - pinctrl-0 = <&mmc0_pins>; - status = "okay"; -}; - -&scifa0 { - pinctrl-0 = <&scifa0_pins>; - pinctrl-names = "default"; - - status = "okay"; -}; - -&sdhi0 { - vmmc-supply = <&vcc_sdhi0>; - bus-width = <4>; - toshiba,mmc-wrprotect-disable; - pinctrl-names = "default"; - pinctrl-0 = <&sdhi0_pins>; - status = "okay"; -}; - -&sdhi1 { - vmmc-supply = <&ape6evm_fixed_3v3>; - bus-width = <4>; - broken-cd; - toshiba,mmc-wrprotect-disable; - pinctrl-names = "default"; - pinctrl-0 = <&sdhi1_pins>; - status = "okay"; -}; diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm.dts b/arch/arm/boot/dts/r8a73a4-ape6evm.dts index 0d50bef01234..81a38ceee098 100644 --- a/arch/arm/boot/dts/r8a73a4-ape6evm.dts +++ b/arch/arm/boot/dts/r8a73a4-ape6evm.dts @@ -22,7 +22,7 @@ }; chosen { - bootargs = "console=ttySC0,115200 ignore_loglevel root=/dev/nfs ip=dhcp rw"; + bootargs = "ignore_loglevel root=/dev/nfs ip=dhcp rw"; stdout-path = &scifa0; }; @@ -72,50 +72,30 @@ regulator-always-on; }; - lbsc { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0 0 0x20000000>; - - ethernet@8000000 { - compatible = "smsc,lan9220", "smsc,lan9115"; - reg = <0x08000000 0x1000>; - interrupt-parent = <&irqc1>; - interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; - phy-mode = "mii"; - reg-io-width = <4>; - smsc,irq-active-high; - smsc,irq-push-pull; - vdd33a-supply = <&ape6evm_fixed_3v3>; - vddvario-supply = <&ape6evm_fixed_1v8>; - }; - }; - leds { compatible = "gpio-leds"; led1 { - gpios = <&pfc 28 GPIO_ACTIVE_LOW>; + gpios = <&pfc 28 GPIO_ACTIVE_HIGH>; label = "GNSS_EN"; }; led2 { - gpios = <&pfc 126 GPIO_ACTIVE_LOW>; + gpios = <&pfc 126 GPIO_ACTIVE_HIGH>; label = "NFC_NRST"; }; led3 { - gpios = <&pfc 132 GPIO_ACTIVE_LOW>; + gpios = <&pfc 132 GPIO_ACTIVE_HIGH>; label = "GNSS_NRST"; }; led4 { - gpios = <&pfc 232 GPIO_ACTIVE_LOW>; + gpios = <&pfc 232 GPIO_ACTIVE_HIGH>; label = "BT_WAKEUP"; }; led5 { - gpios = <&pfc 250 GPIO_ACTIVE_LOW>; + gpios = <&pfc 250 GPIO_ACTIVE_HIGH>; label = "STROBE"; }; led6 { - gpios = <&pfc 288 GPIO_ACTIVE_LOW>; + gpios = <&pfc 288 GPIO_ACTIVE_HIGH>; label = "BBRESETOUT"; }; }; @@ -123,10 +103,14 @@ keyboard { compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&keyboard_pins>; + zero-key { gpios = <&pfc 324 GPIO_ACTIVE_LOW>; linux,code = ; label = "S16"; + gpio-key,wakeup; }; menu-key { @@ -184,6 +168,21 @@ voltage-tolerance = <1>; /* 1% */ }; +&bsc { + ethernet@8000000 { + compatible = "smsc,lan9220", "smsc,lan9115"; + reg = <0x08000000 0x1000>; + interrupt-parent = <&irqc1>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; + phy-mode = "mii"; + reg-io-width = <4>; + smsc,irq-active-high; + smsc,irq-push-pull; + vdd33a-supply = <&ape6evm_fixed_3v3>; + vddvario-supply = <&ape6evm_fixed_1v8>; + }; +}; + &cmt1 { status = "okay"; }; @@ -208,6 +207,12 @@ renesas,groups = "sdhi1_data4", "sdhi1_ctrl"; renesas,function = "sdhi1"; }; + + keyboard_pins: keyboard { + renesas,pins = "PORT324", "PORT325", "PORT326", "PORT327", + "PORT328", "PORT329"; + bias-pull-up; + }; }; &mmcif0 { diff --git a/arch/arm/boot/dts/r8a73a4.dtsi b/arch/arm/boot/dts/r8a73a4.dtsi index 38136d9f6d95..0fd889f88109 100644 --- a/arch/arm/boot/dts/r8a73a4.dtsi +++ b/arch/arm/boot/dts/r8a73a4.dtsi @@ -9,6 +9,7 @@ * kind, whether express or implied. */ +#include #include #include @@ -27,9 +28,15 @@ compatible = "arm,cortex-a15"; reg = <0>; clock-frequency = <1500000000>; + power-domains = <&pd_a2sl>; }; }; + ptm { + compatible = "arm,coresight-etm3x"; + power-domains = <&pd_d4>; + }; + timer { compatible = "arm,armv7-timer"; interrupts = <1 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, @@ -41,11 +48,13 @@ dbsc1: memory-controller@e6790000 { compatible = "renesas,dbsc-r8a73a4"; reg = <0 0xe6790000 0 0x10000>; + power-domains = <&pd_a3bc>; }; dbsc2: memory-controller@e67a0000 { compatible = "renesas,dbsc-r8a73a4"; reg = <0 0xe67a0000 0 0x10000>; + power-domains = <&pd_a3bc>; }; dmac: dma-multiplexer { @@ -87,38 +96,19 @@ "ch8", "ch9", "ch10", "ch11", "ch12", "ch13", "ch14", "ch15", "ch16", "ch17", "ch18", "ch19"; + clocks = <&mstp2_clks R8A73A4_CLK_DMAC>; + power-domains = <&pd_a3sp>; }; }; - pfc: pfc@e6050000 { - compatible = "renesas,pfc-r8a73a4"; - reg = <0 0xe6050000 0 0x9000>; - gpio-controller; - #gpio-cells = <2>; - interrupts-extended = - <&irqc0 0 0>, <&irqc0 1 0>, <&irqc0 2 0>, <&irqc0 3 0>, - <&irqc0 4 0>, <&irqc0 5 0>, <&irqc0 6 0>, <&irqc0 7 0>, - <&irqc0 8 0>, <&irqc0 9 0>, <&irqc0 10 0>, <&irqc0 11 0>, - <&irqc0 12 0>, <&irqc0 13 0>, <&irqc0 14 0>, <&irqc0 15 0>, - <&irqc0 16 0>, <&irqc0 17 0>, <&irqc0 18 0>, <&irqc0 19 0>, - <&irqc0 20 0>, <&irqc0 21 0>, <&irqc0 22 0>, <&irqc0 23 0>, - <&irqc0 24 0>, <&irqc0 25 0>, <&irqc0 26 0>, <&irqc0 27 0>, - <&irqc0 28 0>, <&irqc0 29 0>, <&irqc0 30 0>, <&irqc0 31 0>, - <&irqc1 0 0>, <&irqc1 1 0>, <&irqc1 2 0>, <&irqc1 3 0>, - <&irqc1 4 0>, <&irqc1 5 0>, <&irqc1 6 0>, <&irqc1 7 0>, - <&irqc1 8 0>, <&irqc1 9 0>, <&irqc1 10 0>, <&irqc1 11 0>, - <&irqc1 12 0>, <&irqc1 13 0>, <&irqc1 14 0>, <&irqc1 15 0>, - <&irqc1 16 0>, <&irqc1 17 0>, <&irqc1 18 0>, <&irqc1 19 0>, - <&irqc1 20 0>, <&irqc1 21 0>, <&irqc1 22 0>, <&irqc1 23 0>, - <&irqc1 24 0>, <&irqc1 25 0>; - }; - i2c5: i2c@e60b0000 { #address-cells = <1>; #size-cells = <0>; compatible = "renesas,iic-r8a73a4", "renesas,rmobile-iic"; reg = <0 0xe60b0000 0 0x428>; interrupts = <0 179 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp4_clks R8A73A4_CLK_IIC5>; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -127,6 +117,9 @@ compatible = "renesas,cmt-48-r8a73a4", "renesas,cmt-48-gen2"; reg = <0 0xe6130000 0 0x1004>; interrupts = <0 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A73A4_CLK_CMT1>; + clock-names = "fck"; + power-domains = <&pd_c5>; renesas,channels-mask = <0xff>; @@ -170,6 +163,7 @@ <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>, <0 31 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&pd_c4>; }; irqc1: interrupt-controller@e61c0200 { @@ -203,6 +197,31 @@ <0 55 IRQ_TYPE_LEVEL_HIGH>, <0 56 IRQ_TYPE_LEVEL_HIGH>, <0 57 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&pd_c4>; + }; + + pfc: pfc@e6050000 { + compatible = "renesas,pfc-r8a73a4"; + reg = <0 0xe6050000 0 0x9000>; + gpio-controller; + #gpio-cells = <2>; + interrupts-extended = + <&irqc0 0 0>, <&irqc0 1 0>, <&irqc0 2 0>, <&irqc0 3 0>, + <&irqc0 4 0>, <&irqc0 5 0>, <&irqc0 6 0>, <&irqc0 7 0>, + <&irqc0 8 0>, <&irqc0 9 0>, <&irqc0 10 0>, <&irqc0 11 0>, + <&irqc0 12 0>, <&irqc0 13 0>, <&irqc0 14 0>, <&irqc0 15 0>, + <&irqc0 16 0>, <&irqc0 17 0>, <&irqc0 18 0>, <&irqc0 19 0>, + <&irqc0 20 0>, <&irqc0 21 0>, <&irqc0 22 0>, <&irqc0 23 0>, + <&irqc0 24 0>, <&irqc0 25 0>, <&irqc0 26 0>, <&irqc0 27 0>, + <&irqc0 28 0>, <&irqc0 29 0>, <&irqc0 30 0>, <&irqc0 31 0>, + <&irqc1 0 0>, <&irqc1 1 0>, <&irqc1 2 0>, <&irqc1 3 0>, + <&irqc1 4 0>, <&irqc1 5 0>, <&irqc1 6 0>, <&irqc1 7 0>, + <&irqc1 8 0>, <&irqc1 9 0>, <&irqc1 10 0>, <&irqc1 11 0>, + <&irqc1 12 0>, <&irqc1 13 0>, <&irqc1 14 0>, <&irqc1 15 0>, + <&irqc1 16 0>, <&irqc1 17 0>, <&irqc1 18 0>, <&irqc1 19 0>, + <&irqc1 20 0>, <&irqc1 21 0>, <&irqc1 22 0>, <&irqc1 23 0>, + <&irqc1 24 0>, <&irqc1 25 0>; + power-domains = <&pd_c5>; }; thermal@e61f0000 { @@ -210,6 +229,8 @@ reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>, <0 0xe61f0200 0 0x38>, <0 0xe61f0300 0 0x38>; interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks R8A73A4_CLK_THERMAL>; + power-domains = <&pd_c5>; }; i2c0: i2c@e6500000 { @@ -218,6 +239,8 @@ compatible = "renesas,iic-r8a73a4", "renesas,rmobile-iic"; reg = <0 0xe6500000 0 0x428>; interrupts = <0 174 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A73A4_CLK_IIC0>; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -227,6 +250,8 @@ compatible = "renesas,iic-r8a73a4", "renesas,rmobile-iic"; reg = <0 0xe6510000 0 0x428>; interrupts = <0 175 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A73A4_CLK_IIC1>; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -236,6 +261,8 @@ compatible = "renesas,iic-r8a73a4", "renesas,rmobile-iic"; reg = <0 0xe6520000 0 0x428>; interrupts = <0 176 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A73A4_CLK_IIC2>; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -245,6 +272,8 @@ compatible = "renesas,iic-r8a73a4", "renesas,rmobile-iic"; reg = <0 0xe6530000 0 0x428>; interrupts = <0 177 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp4_clks R8A73A4_CLK_IIC3>; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -254,6 +283,8 @@ compatible = "renesas,iic-r8a73a4", "renesas,rmobile-iic"; reg = <0 0xe6540000 0 0x428>; interrupts = <0 178 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp4_clks R8A73A4_CLK_IIC4>; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -263,6 +294,8 @@ compatible = "renesas,iic-r8a73a4", "renesas,rmobile-iic"; reg = <0 0xe6550000 0 0x428>; interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A73A4_CLK_IIC6>; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -272,6 +305,8 @@ compatible = "renesas,iic-r8a73a4", "renesas,rmobile-iic"; reg = <0 0xe6560000 0 0x428>; interrupts = <0 185 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A73A4_CLK_IIC7>; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -281,6 +316,8 @@ compatible = "renesas,iic-r8a73a4", "renesas,rmobile-iic"; reg = <0 0xe6570000 0 0x428>; interrupts = <0 173 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks R8A73A4_CLK_IIC8>; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -288,6 +325,9 @@ compatible = "renesas,scifb-r8a73a4", "renesas,scifb"; reg = <0 0xe6c20000 0 0x100>; interrupts = <0 148 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A73A4_CLK_SCIFB0>; + clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -295,6 +335,9 @@ compatible = "renesas,scifb-r8a73a4", "renesas,scifb"; reg = <0 0xe6c30000 0 0x100>; interrupts = <0 149 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A73A4_CLK_SCIFB1>; + clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -302,6 +345,9 @@ compatible = "renesas,scifa-r8a73a4", "renesas,scifa"; reg = <0 0xe6c40000 0 0x100>; interrupts = <0 144 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A73A4_CLK_SCIFA0>; + clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -309,6 +355,9 @@ compatible = "renesas,scifa-r8a73a4", "renesas,scifa"; reg = <0 0xe6c50000 0 0x100>; interrupts = <0 145 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A73A4_CLK_SCIFA1>; + clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -316,6 +365,9 @@ compatible = "renesas,scifb-r8a73a4", "renesas,scifb"; reg = <0 0xe6ce0000 0 0x100>; interrupts = <0 150 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A73A4_CLK_SCIFB2>; + clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -323,6 +375,9 @@ compatible = "renesas,scifb-r8a73a4", "renesas,scifb"; reg = <0 0xe6cf0000 0 0x100>; interrupts = <0 151 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A73A4_CLK_SCIFB3>; + clock-names = "sci_ick"; + power-domains = <&pd_c4>; status = "disabled"; }; @@ -330,6 +385,8 @@ compatible = "renesas,sdhi-r8a73a4"; reg = <0 0xee100000 0 0x100>; interrupts = <0 165 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A73A4_CLK_SDHI0>; + power-domains = <&pd_a3sp>; cap-sd-highspeed; status = "disabled"; }; @@ -338,6 +395,8 @@ compatible = "renesas,sdhi-r8a73a4"; reg = <0 0xee120000 0 0x100>; interrupts = <0 166 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A73A4_CLK_SDHI1>; + power-domains = <&pd_a3sp>; cap-sd-highspeed; status = "disabled"; }; @@ -346,6 +405,8 @@ compatible = "renesas,sdhi-r8a73a4"; reg = <0 0xee140000 0 0x100>; interrupts = <0 167 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A73A4_CLK_SDHI2>; + power-domains = <&pd_a3sp>; cap-sd-highspeed; status = "disabled"; }; @@ -354,6 +415,8 @@ compatible = "renesas,sh-mmcif"; reg = <0 0xee200000 0 0x80>; interrupts = <0 169 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A73A4_CLK_MMCIF0>; + power-domains = <&pd_a3sp>; reg-io-width = <4>; status = "disabled"; }; @@ -362,6 +425,8 @@ compatible = "renesas,sh-mmcif"; reg = <0 0xee220000 0 0x80>; interrupts = <0 170 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A73A4_CLK_MMCIF1>; + power-domains = <&pd_a3sp>; reg-io-width = <4>; status = "disabled"; }; @@ -377,4 +442,450 @@ <0 0xf1006000 0 0x2000>; interrupts = <1 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; }; + + bsc: bus@fec10000 { + compatible = "renesas,bsc-r8a73a4", "renesas,bsc", + "simple-pm-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0x20000000>; + reg = <0 0xfec10000 0 0x400>; + clocks = <&zb_clk>; + power-domains = <&pd_c4>; + }; + + clocks { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* External root clocks */ + extalr_clk: extalr_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "extalr"; + }; + extal1_clk: extal1_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + clock-output-names = "extal1"; + }; + extal2_clk: extal2_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; + clock-output-names = "extal2"; + }; + fsiack_clk: fsiack_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* This value must be overridden by the board. */ + clock-frequency = <0>; + clock-output-names = "fsiack"; + }; + fsibck_clk: fsibck_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* This value must be overridden by the board. */ + clock-frequency = <0>; + clock-output-names = "fsibck"; + }; + + /* Special CPG clocks */ + cpg_clocks: cpg_clocks@e6150000 { + compatible = "renesas,r8a73a4-cpg-clocks"; + reg = <0 0xe6150000 0 0x10000>; + clocks = <&extal1_clk>, <&extal2_clk>; + #clock-cells = <1>; + clock-output-names = "main", "pll0", "pll1", "pll2", + "pll2s", "pll2h", "z", "z2", + "i", "m3", "b", "m1", "m2", + "zx", "zs", "hp"; + }; + + /* Variable factor clocks (DIV6) */ + zb_clk: zb_clk@e6150010 { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe6150010 0 4>; + clocks = <&pll1_div2_clk>, <0>, + <&cpg_clocks R8A73A4_CLK_PLL2S>, <0>; + #clock-cells = <0>; + clock-output-names = "zb"; + }; + sdhi0_clk: sdhi0_clk@e6150074 { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe6150074 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <0>, <&extal2_clk>; + #clock-cells = <0>; + clock-output-names = "sdhi0ck"; + }; + sdhi1_clk: sdhi1_clk@e6150078 { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe6150078 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <0>, <&extal2_clk>; + #clock-cells = <0>; + clock-output-names = "sdhi1ck"; + }; + sdhi2_clk: sdhi2_clk@e615007c { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe615007c 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <0>, <&extal2_clk>; + #clock-cells = <0>; + clock-output-names = "sdhi2ck"; + }; + mmc0_clk: mmc0_clk@e6150240 { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe6150240 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <0>, <&extal2_clk>; + #clock-cells = <0>; + clock-output-names = "mmc0"; + }; + mmc1_clk: mmc1_clk@e6150244 { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe6150244 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <0>, <&extal2_clk>; + #clock-cells = <0>; + clock-output-names = "mmc1"; + }; + vclk1_clk: vclk1_clk@e6150008 { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe6150008 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <0>, <&extal2_clk>, <&main_div2_clk>, + <&extalr_clk>, <0>, <0>; + #clock-cells = <0>; + clock-output-names = "vclk1"; + }; + vclk2_clk: vclk2_clk@e615000c { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe615000c 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <0>, <&extal2_clk>, <&main_div2_clk>, + <&extalr_clk>, <0>, <0>; + #clock-cells = <0>; + clock-output-names = "vclk2"; + }; + vclk3_clk: vclk3_clk@e615001c { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe615001c 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <0>, <&extal2_clk>, <&main_div2_clk>, + <&extalr_clk>, <0>, <0>; + #clock-cells = <0>; + clock-output-names = "vclk3"; + }; + vclk4_clk: vclk4_clk@e6150014 { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe6150014 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <0>, <&extal2_clk>, <&main_div2_clk>, + <&extalr_clk>, <0>, <0>; + #clock-cells = <0>; + clock-output-names = "vclk4"; + }; + vclk5_clk: vclk5_clk@e6150034 { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe6150034 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <0>, <&extal2_clk>, <&main_div2_clk>, + <&extalr_clk>, <0>, <0>; + #clock-cells = <0>; + clock-output-names = "vclk5"; + }; + fsia_clk: fsia_clk@e6150018 { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe6150018 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <&fsiack_clk>, <0>; + #clock-cells = <0>; + clock-output-names = "fsia"; + }; + fsib_clk: fsib_clk@e6150090 { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe6150090 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <&fsibck_clk>, <0>; + #clock-cells = <0>; + clock-output-names = "fsib"; + }; + mp_clk: mp_clk@e6150080 { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe6150080 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <&extal2_clk>, <&extal2_clk>; + #clock-cells = <0>; + clock-output-names = "mp"; + }; + m4_clk: m4_clk@e6150098 { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe6150098 0 4>; + clocks = <&cpg_clocks R8A73A4_CLK_PLL2S>; + #clock-cells = <0>; + clock-output-names = "m4"; + }; + hsi_clk: hsi_clk@e615026c { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe615026c 0 4>; + clocks = <&cpg_clocks R8A73A4_CLK_PLL2H>, <&pll1_div2_clk>, + <&cpg_clocks R8A73A4_CLK_PLL2S>, <0>; + #clock-cells = <0>; + clock-output-names = "hsi"; + }; + spuv_clk: spuv_clk@e6150094 { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe6150094 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <&extal2_clk>, <&extal2_clk>; + #clock-cells = <0>; + clock-output-names = "spuv"; + }; + + /* Fixed factor clocks */ + main_div2_clk: main_div2_clk { + compatible = "fixed-factor-clock"; + clocks = <&cpg_clocks R8A73A4_CLK_MAIN>; + #clock-cells = <0>; + clock-div = <2>; + clock-mult = <1>; + clock-output-names = "main_div2"; + }; + pll0_div2_clk: pll0_div2_clk { + compatible = "fixed-factor-clock"; + clocks = <&cpg_clocks R8A73A4_CLK_PLL0>; + #clock-cells = <0>; + clock-div = <2>; + clock-mult = <1>; + clock-output-names = "pll0_div2"; + }; + pll1_div2_clk: pll1_div2_clk { + compatible = "fixed-factor-clock"; + clocks = <&cpg_clocks R8A73A4_CLK_PLL1>; + #clock-cells = <0>; + clock-div = <2>; + clock-mult = <1>; + clock-output-names = "pll1_div2"; + }; + extal1_div2_clk: extal1_div2_clk { + compatible = "fixed-factor-clock"; + clocks = <&extal1_clk>; + #clock-cells = <0>; + clock-div = <2>; + clock-mult = <1>; + clock-output-names = "extal1_div2"; + }; + + /* Gate clocks */ + mstp2_clks: mstp2_clks@e6150138 { + compatible = "renesas,r8a73a4-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0 0xe6150138 0 4>, <0 0xe6150040 0 4>; + clocks = <&mp_clk>, <&mp_clk>, <&mp_clk>, <&mp_clk>, + <&mp_clk>, <&mp_clk>, <&cpg_clocks R8A73A4_CLK_HP>; + #clock-cells = <1>; + clock-indices = < + R8A73A4_CLK_SCIFA0 R8A73A4_CLK_SCIFA1 + R8A73A4_CLK_SCIFB0 R8A73A4_CLK_SCIFB1 + R8A73A4_CLK_SCIFB2 R8A73A4_CLK_SCIFB3 + R8A73A4_CLK_DMAC + >; + clock-output-names = + "scifa0", "scifa1", "scifb0", "scifb1", + "scifb2", "scifb3", "dmac"; + }; + mstp3_clks: mstp3_clks@e615013c { + compatible = "renesas,r8a73a4-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0 0xe615013c 0 4>, <0 0xe6150048 0 4>; + clocks = <&cpg_clocks R8A73A4_CLK_HP>, <&mmc1_clk>, + <&sdhi2_clk>, <&sdhi1_clk>, <&sdhi0_clk>, + <&mmc0_clk>, <&cpg_clocks R8A73A4_CLK_HP>, + <&cpg_clocks R8A73A4_CLK_HP>, <&cpg_clocks + R8A73A4_CLK_HP>, <&cpg_clocks + R8A73A4_CLK_HP>, <&extalr_clk>; + #clock-cells = <1>; + clock-indices = < + R8A73A4_CLK_IIC2 R8A73A4_CLK_MMCIF1 + R8A73A4_CLK_SDHI2 R8A73A4_CLK_SDHI1 + R8A73A4_CLK_SDHI0 R8A73A4_CLK_MMCIF0 + R8A73A4_CLK_IIC6 R8A73A4_CLK_IIC7 + R8A73A4_CLK_IIC0 R8A73A4_CLK_IIC1 + R8A73A4_CLK_CMT1 + >; + clock-output-names = + "iic2", "mmcif1", "sdhi2", "sdhi1", "sdhi0", + "mmcif0", "iic6", "iic7", "iic0", "iic1", + "cmt1"; + }; + mstp4_clks: mstp4_clks@e6150140 { + compatible = "renesas,r8a73a4-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0 0xe6150140 0 4>, <0 0xe615004c 0 4>; + clocks = <&main_div2_clk>, <&cpg_clocks R8A73A4_CLK_HP>, + <&cpg_clocks R8A73A4_CLK_HP>; + #clock-cells = <1>; + clock-indices = < + R8A73A4_CLK_IIC5 R8A73A4_CLK_IIC4 + R8A73A4_CLK_IIC3 + >; + clock-output-names = + "iic5", "iic4", "iic3"; + }; + mstp5_clks: mstp5_clks@e6150144 { + compatible = "renesas,r8a73a4-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0 0xe6150144 0 4>, <0 0xe615003c 0 4>; + clocks = <&extal2_clk>, <&cpg_clocks R8A73A4_CLK_HP>; + #clock-cells = <1>; + clock-indices = < + R8A73A4_CLK_THERMAL R8A73A4_CLK_IIC8 + >; + clock-output-names = + "thermal", "iic8"; + }; + }; + + sysc: system-controller@e6180000 { + compatible = "renesas,sysc-r8a73a4", "renesas,sysc-rmobile"; + reg = <0 0xe6180000 0 0x8000>, <0 0xe6188000 0 0x8000>; + + pm-domains { + pd_c5: c5 { + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_c4: c4@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_a3sg: a3sg@16 { + reg = <16>; + #power-domain-cells = <0>; + }; + + pd_a3ex: a3ex@17 { + reg = <17>; + #power-domain-cells = <0>; + }; + + pd_a3sp: a3sp@18 { + reg = <18>; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_a2us: a2us@19 { + reg = <19>; + #power-domain-cells = <0>; + }; + }; + + pd_a3sm: a3sm@20 { + reg = <20>; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_a2sl: a2sl@21 { + reg = <21>; + #power-domain-cells = <0>; + }; + }; + + pd_a3km: a3km@22 { + reg = <22>; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_a2kl: a2kl@23 { + reg = <23>; + #power-domain-cells = <0>; + }; + }; + }; + + pd_c4ma: c4ma@1 { + reg = <1>; + #power-domain-cells = <0>; + }; + + pd_c4cl: c4cl@2 { + reg = <2>; + #power-domain-cells = <0>; + }; + + pd_d4: d4@3 { + reg = <3>; + #power-domain-cells = <0>; + }; + + pd_a4bc: a4bc@4 { + reg = <4>; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_a3bc: a3bc@5 { + reg = <5>; + #power-domain-cells = <0>; + }; + }; + + pd_a4l: a4l@6 { + reg = <6>; + #power-domain-cells = <0>; + }; + + pd_a4lc: a4lc@7 { + reg = <7>; + #power-domain-cells = <0>; + }; + + pd_a4mp: a4mp@8 { + reg = <8>; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_a3mp: a3mp@9 { + reg = <9>; + #power-domain-cells = <0>; + }; + + pd_a3vc: a3vc@10 { + reg = <10>; + #power-domain-cells = <0>; + }; + }; + + pd_a4sf: a4sf@11 { + reg = <11>; + #power-domain-cells = <0>; + }; + + pd_a3r: a3r@12 { + reg = <12>; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_a2rv: a2rv@13 { + reg = <13>; + #power-domain-cells = <0>; + }; + + pd_a2is: a2is@14 { + reg = <14>; + #power-domain-cells = <0>; + }; + }; + }; + }; + }; }; diff --git a/arch/arm/boot/dts/r8a7740.dtsi b/arch/arm/boot/dts/r8a7740.dtsi index 8a092605d641..83c1c3ca1b8f 100644 --- a/arch/arm/boot/dts/r8a7740.dtsi +++ b/arch/arm/boot/dts/r8a7740.dtsi @@ -431,6 +431,18 @@ clock-frequency = <27000000>; clock-output-names = "dv"; }; + fmsick_clk: fmsick_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "fmsick"; + }; + fmsock_clk: fmsock_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "fmsock"; + }; fsiack_clk: fsiack_clk { compatible = "fixed-clock"; #clock-cells = <0>; @@ -459,13 +471,78 @@ }; /* Variable factor clocks (DIV6) */ + vclk1_clk: vclk1_clk@e6150008 { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe6150008 4>; + clocks = <&pllc1_div2_clk>, <0>, <&dv_clk>, + <&cpg_clocks R8A7740_CLK_USB24S>, + <&extal1_div2_clk>, <&extalr_clk>, <0>, + <0>; + #clock-cells = <0>; + clock-output-names = "vclk1"; + }; + vclk2_clk: vclk2_clk@e615000c { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe615000c 4>; + clocks = <&pllc1_div2_clk>, <0>, <&dv_clk>, + <&cpg_clocks R8A7740_CLK_USB24S>, + <&extal1_div2_clk>, <&extalr_clk>, <0>, + <0>; + #clock-cells = <0>; + clock-output-names = "vclk2"; + }; + fmsi_clk: fmsi_clk@e6150010 { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe6150010 4>; + clocks = <&pllc1_div2_clk>, <&fmsick_clk>, <0>, <0>; + #clock-cells = <0>; + clock-output-names = "fmsi"; + }; + fmso_clk: fmso_clk@e6150014 { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe6150014 4>; + clocks = <&pllc1_div2_clk>, <&fmsock_clk>, <0>, <0>; + #clock-cells = <0>; + clock-output-names = "fmso"; + }; + fsia_clk: fsia_clk@e6150018 { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe6150018 4>; + clocks = <&pllc1_div2_clk>, <&fsiack_clk>, <0>, <0>; + #clock-cells = <0>; + clock-output-names = "fsia"; + }; sub_clk: sub_clk@e6150080 { compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150080 4>; - clocks = <&pllc1_div2_clk>; + clocks = <&pllc1_div2_clk>, + <&cpg_clocks R8A7740_CLK_USB24S>, <0>, <0>; #clock-cells = <0>; clock-output-names = "sub"; }; + spu_clk: spu_clk@e6150084 { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe6150084 4>; + clocks = <&pllc1_div2_clk>, + <&cpg_clocks R8A7740_CLK_USB24S>, <0>, <0>; + #clock-cells = <0>; + clock-output-names = "spu"; + }; + vou_clk: vou_clk@e6150088 { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe6150088 4>; + clocks = <&pllc1_div2_clk>, <&extal1_clk>, <&dv_clk>, + <0>; + #clock-cells = <0>; + clock-output-names = "vou"; + }; + stpro_clk: stpro_clk@e615009c { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe615009c 4>; + clocks = <&cpg_clocks R8A7740_CLK_PLLC0>; + #clock-cells = <0>; + clock-output-names = "stpro"; + }; /* Fixed factor clocks */ pllc1_div2_clk: pllc1_div2_clk { diff --git a/arch/arm/boot/dts/r8a7778-bockw.dts b/arch/arm/boot/dts/r8a7778-bockw.dts index 46a884d45175..787fa6f9f46d 100644 --- a/arch/arm/boot/dts/r8a7778-bockw.dts +++ b/arch/arm/boot/dts/r8a7778-bockw.dts @@ -16,17 +16,191 @@ /dts-v1/; #include "r8a7778.dtsi" +#include +#include / { model = "bockw"; compatible = "renesas,bockw", "renesas,r8a7778"; + aliases { + serial0 = &scif0; + }; + chosen { bootargs = "console=ttySC0,115200 ignore_loglevel ip=dhcp root=/dev/nfs rw"; + stdout-path = &scif0; }; memory { device_type = "memory"; reg = <0x60000000 0x10000000>; }; + + fixedregulator3v3: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sound { + compatible = "simple-audio-card"; + + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&sndcodec>; + simple-audio-card,frame-master = <&sndcodec>; + + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + }; + + sndcodec: simple-audio-card,codec { + sound-dai = <&ak4643>; + system-clock-frequency = <11289600>; + }; + }; +}; + +&bsc { + ethernet@18300000 { + compatible = "smsc,lan9220", "smsc,lan9115"; + reg = <0x18300000 0x1000>; + + phy-mode = "mii"; + interrupt-parent = <&irqpin>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + reg-io-width = <4>; + vddvario-supply = <&fixedregulator3v3>; + vdd33a-supply = <&fixedregulator3v3>; + }; +}; + +&extal_clk { + clock-frequency = <33333333>; +}; + +&i2c0 { + status = "okay"; + + ak4643: sound-codec@12 { + compatible = "asahi-kasei,ak4643"; + #sound-dai-cells = <0>; + reg = <0x12>; + }; + + camera@41 { + compatible = "oki,ml86v7667"; + reg = <0x41>; + }; + + camera@43 { + compatible = "oki,ml86v7667"; + reg = <0x43>; + }; + + rx8581: rtc@51 { + compatible = "epson,rx8581"; + reg = <0x51>; + }; +}; + +&mmcif { + pinctrl-0 = <&mmc_pins>; + pinctrl-names = "default"; + + vmmc-supply = <&fixedregulator3v3>; + bus-width = <8>; + broken-cd; + status = "okay"; +}; + +&irqpin { + status = "okay"; +}; + +&tmu0 { + status = "okay"; +}; + +&pfc { + scif0_pins: serial0 { + renesas,groups = "scif0_data_a", "scif0_ctrl"; + renesas,function = "scif0"; + }; + + mmc_pins: mmc { + renesas,groups = "mmc_data8", "mmc_ctrl"; + renesas,function = "mmc"; + }; + + sdhi0_pins: sd0 { + renesas,groups = "sdhi0_data4", "sdhi0_ctrl", + "sdhi0_cd"; + renesas,function = "sdhi0"; + }; + + hspi0_pins: hspi0 { + renesas,groups = "hspi0_a"; + renesas,function = "hspi0"; + }; + + usb0_pins: usb0 { + renesas,groups = "usb0"; + renesas,function = "usb0"; + }; + + usb1_pins: usb1 { + renesas,groups = "usb1"; + renesas,function = "usb1"; + }; + + vin0_pins: vin0 { + renesas,groups = "vin0_data8", "vin0_clk"; + renesas,function = "vin0"; + }; + + vin1_pins: vin1 { + renesas,groups = "vin1_data8", "vin1_clk"; + renesas,function = "vin1"; + }; +}; + +&sdhi0 { + pinctrl-0 = <&sdhi0_pins>; + pinctrl-names = "default"; + + vmmc-supply = <&fixedregulator3v3>; + bus-width = <4>; + status = "okay"; + wp-gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>; +}; + +&hspi0 { + pinctrl-0 = <&hspi0_pins>; + pinctrl-names = "default"; + status = "okay"; + + flash: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,s25fl008k"; + reg = <0>; + spi-max-frequency = <104000000>; + m25p,fast-read; + + partition@0 { + label = "data(spi)"; + reg = <0x00000000 0x00100000>; + }; + }; +}; + +&scif0 { + pinctrl-0 = <&scif0_pins>; + pinctrl-names = "default"; + + status = "okay"; }; diff --git a/arch/arm/boot/dts/r8a7778.dtsi b/arch/arm/boot/dts/r8a7778.dtsi index ef8533910029..868f97309533 100644 --- a/arch/arm/boot/dts/r8a7778.dtsi +++ b/arch/arm/boot/dts/r8a7778.dtsi @@ -16,6 +16,7 @@ /include/ "skeleton.dtsi" +#include #include / { @@ -40,6 +41,24 @@ spi2 = &hspi2; }; + bsc: bus@1c000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x1c000000>; + }; + + ether: ethernet@fde00000 { + compatible = "renesas,ether-r8a7778"; + reg = <0xfde00000 0x400>; + interrupts = <0 105 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp1_clks R8A7778_CLK_ETHER>; + phy-mode = "rmii"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + gic: interrupt-controller@fe438000 { compatible = "arm,cortex-a9-gic"; #interrupt-cells = <3>; @@ -132,6 +151,7 @@ compatible = "renesas,i2c-r8a7778"; reg = <0xffc70000 0x1000>; interrupts = <0 67 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_I2C0>; status = "disabled"; }; @@ -141,6 +161,7 @@ compatible = "renesas,i2c-r8a7778"; reg = <0xffc71000 0x1000>; interrupts = <0 78 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_I2C1>; status = "disabled"; }; @@ -150,6 +171,7 @@ compatible = "renesas,i2c-r8a7778"; reg = <0xffc72000 0x1000>; interrupts = <0 76 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_I2C2>; status = "disabled"; }; @@ -159,6 +181,7 @@ compatible = "renesas,i2c-r8a7778"; reg = <0xffc73000 0x1000>; interrupts = <0 77 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_I2C3>; status = "disabled"; }; @@ -168,6 +191,8 @@ interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>, <0 33 IRQ_TYPE_LEVEL_HIGH>, <0 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_TMU0>; + clock-names = "fck"; #renesas,channels = <3>; @@ -180,6 +205,8 @@ interrupts = <0 36 IRQ_TYPE_LEVEL_HIGH>, <0 37 IRQ_TYPE_LEVEL_HIGH>, <0 38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_TMU1>; + clock-names = "fck"; #renesas,channels = <3>; @@ -192,16 +219,75 @@ interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>, <0 41 IRQ_TYPE_LEVEL_HIGH>, <0 42 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_TMU2>; + clock-names = "fck"; #renesas,channels = <3>; status = "disabled"; }; + rcar_sound: sound@ffd90000 { + #sound-dai-cells = <1>; + compatible = "renesas,rcar_sound-r8a7778", "renesas,rcar_sound-gen1"; + reg = <0xffd90000 0x1000>, /* SRU */ + <0xffd91000 0x1240>, /* SSI */ + <0xfffe0000 0x24>; /* ADG */ + clocks = <&mstp3_clks R8A7778_CLK_SSI8>, + <&mstp3_clks R8A7778_CLK_SSI7>, + <&mstp3_clks R8A7778_CLK_SSI6>, + <&mstp3_clks R8A7778_CLK_SSI5>, + <&mstp3_clks R8A7778_CLK_SSI4>, + <&mstp0_clks R8A7778_CLK_SSI3>, + <&mstp0_clks R8A7778_CLK_SSI2>, + <&mstp0_clks R8A7778_CLK_SSI1>, + <&mstp0_clks R8A7778_CLK_SSI0>, + <&mstp5_clks R8A7778_CLK_SRU_SRC8>, + <&mstp5_clks R8A7778_CLK_SRU_SRC7>, + <&mstp5_clks R8A7778_CLK_SRU_SRC6>, + <&mstp5_clks R8A7778_CLK_SRU_SRC5>, + <&mstp5_clks R8A7778_CLK_SRU_SRC4>, + <&mstp5_clks R8A7778_CLK_SRU_SRC3>, + <&mstp5_clks R8A7778_CLK_SRU_SRC2>, + <&mstp5_clks R8A7778_CLK_SRU_SRC1>, + <&mstp5_clks R8A7778_CLK_SRU_SRC0>, + <&audio_clk_a>, <&audio_clk_b>, <&audio_clk_c>, + <&cpg_clocks R8A7778_CLK_S1>; + clock-names = "ssi.8", "ssi.7", "ssi.6", "ssi.5", "ssi.4", + "ssi.3", "ssi.2", "ssi.1", "ssi.0", + "src.8", "src.7", "src.6", "src.5", "src.4", + "src.3", "src.2", "src.1", "src.0", + "clk_a", "clk_b", "clk_c", "clk_i"; + + status = "disabled"; + + rcar_sound,src { + src3: src@3 { }; + src4: src@4 { }; + src5: src@5 { }; + src6: src@6 { }; + src7: src@7 { }; + src8: src@8 { }; + src9: src@9 { }; + }; + + rcar_sound,ssi { + ssi3: ssi@3 { interrupts = <0 0x85 IRQ_TYPE_LEVEL_HIGH>; }; + ssi4: ssi@4 { interrupts = <0 0x85 IRQ_TYPE_LEVEL_HIGH>; }; + ssi5: ssi@5 { interrupts = <0 0x86 IRQ_TYPE_LEVEL_HIGH>; }; + ssi6: ssi@6 { interrupts = <0 0x86 IRQ_TYPE_LEVEL_HIGH>; }; + ssi7: ssi@7 { interrupts = <0 0x86 IRQ_TYPE_LEVEL_HIGH>; }; + ssi8: ssi@8 { interrupts = <0 0x86 IRQ_TYPE_LEVEL_HIGH>; }; + ssi9: ssi@9 { interrupts = <0 0x86 IRQ_TYPE_LEVEL_HIGH>; }; + }; + }; + scif0: serial@ffe40000 { compatible = "renesas,scif-r8a7778", "renesas,scif"; reg = <0xffe40000 0x100>; interrupts = <0 70 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_SCIF0>; + clock-names = "sci_ick"; status = "disabled"; }; @@ -209,6 +295,8 @@ compatible = "renesas,scif-r8a7778", "renesas,scif"; reg = <0xffe41000 0x100>; interrupts = <0 71 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_SCIF1>; + clock-names = "sci_ick"; status = "disabled"; }; @@ -216,6 +304,8 @@ compatible = "renesas,scif-r8a7778", "renesas,scif"; reg = <0xffe42000 0x100>; interrupts = <0 72 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_SCIF2>; + clock-names = "sci_ick"; status = "disabled"; }; @@ -223,6 +313,8 @@ compatible = "renesas,scif-r8a7778", "renesas,scif"; reg = <0xffe43000 0x100>; interrupts = <0 73 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_SCIF3>; + clock-names = "sci_ick"; status = "disabled"; }; @@ -230,6 +322,8 @@ compatible = "renesas,scif-r8a7778", "renesas,scif"; reg = <0xffe44000 0x100>; interrupts = <0 74 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_SCIF4>; + clock-names = "sci_ick"; status = "disabled"; }; @@ -237,6 +331,8 @@ compatible = "renesas,scif-r8a7778", "renesas,scif"; reg = <0xffe45000 0x100>; interrupts = <0 75 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_SCIF5>; + clock-names = "sci_ick"; status = "disabled"; }; @@ -244,6 +340,7 @@ compatible = "renesas,sh-mmcif"; reg = <0xffe4e000 0x100>; interrupts = <0 61 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7778_CLK_MMC>; status = "disabled"; }; @@ -251,6 +348,7 @@ compatible = "renesas,sdhi-r8a7778"; reg = <0xffe4c000 0x100>; interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7778_CLK_SDHI0>; status = "disabled"; }; @@ -258,6 +356,7 @@ compatible = "renesas,sdhi-r8a7778"; reg = <0xffe4d000 0x100>; interrupts = <0 88 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7778_CLK_SDHI1>; status = "disabled"; }; @@ -265,6 +364,7 @@ compatible = "renesas,sdhi-r8a7778"; reg = <0xffe4f000 0x100>; interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7778_CLK_SDHI2>; status = "disabled"; }; @@ -272,6 +372,7 @@ compatible = "renesas,hspi-r8a7778", "renesas,hspi"; reg = <0xfffc7000 0x18>; interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_HSPI>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -281,6 +382,7 @@ compatible = "renesas,hspi-r8a7778", "renesas,hspi"; reg = <0xfffc8000 0x18>; interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_HSPI>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -290,8 +392,199 @@ compatible = "renesas,hspi-r8a7778", "renesas,hspi"; reg = <0xfffc6000 0x18>; interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7778_CLK_HSPI>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + /* External input clock */ + extal_clk: extal_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "extal"; + }; + + /* Special CPG clocks */ + cpg_clocks: cpg_clocks@ffc80000 { + compatible = "renesas,r8a7778-cpg-clocks"; + reg = <0xffc80000 0x80>; + #clock-cells = <1>; + clocks = <&extal_clk>; + clock-output-names = "plla", "pllb", "b", + "out", "p", "s", "s1"; + }; + + /* Audio clocks; frequencies are set by boards if applicable. */ + audio_clk_a: audio_clk_a { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-output-names = "audio_clk_a"; + }; + audio_clk_b: audio_clk_b { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-output-names = "audio_clk_b"; + }; + audio_clk_c: audio_clk_c { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-output-names = "audio_clk_c"; + }; + + /* Fixed ratio clocks */ + g_clk: g_clk { + compatible = "fixed-factor-clock"; + clocks = <&cpg_clocks R8A7778_CLK_PLLA>; + #clock-cells = <0>; + clock-div = <12>; + clock-mult = <1>; + clock-output-names = "g"; + }; + i_clk: i_clk { + compatible = "fixed-factor-clock"; + clocks = <&cpg_clocks R8A7778_CLK_PLLA>; + #clock-cells = <0>; + clock-div = <1>; + clock-mult = <1>; + clock-output-names = "i"; + }; + s3_clk: s3_clk { + compatible = "fixed-factor-clock"; + clocks = <&cpg_clocks R8A7778_CLK_PLLA>; + #clock-cells = <0>; + clock-div = <4>; + clock-mult = <1>; + clock-output-names = "s3"; + }; + s4_clk: s4_clk { + compatible = "fixed-factor-clock"; + clocks = <&cpg_clocks R8A7778_CLK_PLLA>; + #clock-cells = <0>; + clock-div = <8>; + clock-mult = <1>; + clock-output-names = "s4"; + }; + z_clk: z_clk { + compatible = "fixed-factor-clock"; + clocks = <&cpg_clocks R8A7778_CLK_PLLB>; + #clock-cells = <0>; + clock-div = <1>; + clock-mult = <1>; + clock-output-names = "z"; + }; + + /* Gate clocks */ + mstp0_clks: mstp0_clks@ffc80030 { + compatible = "renesas,r8a7778-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0xffc80030 4>; + clocks = <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_S>; + #clock-cells = <1>; + clock-indices = < + R8A7778_CLK_I2C0 R8A7778_CLK_I2C1 + R8A7778_CLK_I2C2 R8A7778_CLK_I2C3 + R8A7778_CLK_SCIF0 R8A7778_CLK_SCIF1 + R8A7778_CLK_SCIF2 R8A7778_CLK_SCIF3 + R8A7778_CLK_SCIF4 R8A7778_CLK_SCIF5 + R8A7778_CLK_TMU0 R8A7778_CLK_TMU1 + R8A7778_CLK_TMU2 R8A7778_CLK_SSI0 + R8A7778_CLK_SSI1 R8A7778_CLK_SSI2 + R8A7778_CLK_SSI3 R8A7778_CLK_SRU + R8A7778_CLK_HSPI + >; + clock-output-names = + "i2c0", "i2c1", "i2c2", "i2c3", "scif0", + "scif1", "scif2", "scif3", "scif4", "scif5", + "tmu0", "tmu1", "tmu2", "ssi0", "ssi1", + "ssi2", "ssi3", "sru", "hspi"; + }; + mstp1_clks: mstp1_clks@ffc80034 { + compatible = "renesas,r8a7778-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0xffc80034 4>, <0xffc80044 4>; + clocks = <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_S>, + <&cpg_clocks R8A7778_CLK_S>, + <&cpg_clocks R8A7778_CLK_P>; + #clock-cells = <1>; + clock-indices = < + R8A7778_CLK_ETHER R8A7778_CLK_VIN0 + R8A7778_CLK_VIN1 R8A7778_CLK_USB + >; + clock-output-names = + "ether", "vin0", "vin1", "usb"; + }; + mstp3_clks: mstp3_clks@ffc8003c { + compatible = "renesas,r8a7778-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0xffc8003c 4>; + clocks = <&s4_clk>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>; + #clock-cells = <1>; + clock-indices = < + R8A7778_CLK_MMC R8A7778_CLK_SDHI0 + R8A7778_CLK_SDHI1 R8A7778_CLK_SDHI2 + R8A7778_CLK_SSI4 R8A7778_CLK_SSI5 + R8A7778_CLK_SSI6 R8A7778_CLK_SSI7 + R8A7778_CLK_SSI8 + >; + clock-output-names = + "mmc", "sdhi0", "sdhi1", "sdhi2", "ssi4", + "ssi5", "ssi6", "ssi7", "ssi8"; + }; + mstp5_clks: mstp5_clks@ffc80054 { + compatible = "renesas,r8a7778-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0xffc80054 4>; + clocks = <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>, + <&cpg_clocks R8A7778_CLK_P>; + #clock-cells = <1>; + clock-indices = < + R8A7778_CLK_SRU_SRC0 R8A7778_CLK_SRU_SRC1 + R8A7778_CLK_SRU_SRC2 R8A7778_CLK_SRU_SRC3 + R8A7778_CLK_SRU_SRC4 R8A7778_CLK_SRU_SRC5 + R8A7778_CLK_SRU_SRC6 R8A7778_CLK_SRU_SRC7 + R8A7778_CLK_SRU_SRC8 + >; + clock-output-names = + "sru-src0", "sru-src1", "sru-src2", + "sru-src3", "sru-src4", "sru-src5", + "sru-src6", "sru-src7", "sru-src8"; + }; + }; }; diff --git a/arch/arm/boot/dts/r8a7779-marzen.dts b/arch/arm/boot/dts/r8a7779-marzen.dts index e83d40e24bcd..540756cdf391 100644 --- a/arch/arm/boot/dts/r8a7779-marzen.dts +++ b/arch/arm/boot/dts/r8a7779-marzen.dts @@ -122,6 +122,12 @@ }; }; }; + + x3_clk: x3-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <65000000>; + }; }; &du { @@ -129,6 +135,9 @@ pinctrl-names = "default"; status = "okay"; + clocks = <&mstp1_clks R8A7779_CLK_DU>, <&x3_clk>; + clock-names = "du", "dclkin.0"; + ports { port@0 { endpoint { diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts index 0c3b6783b72a..aaa4f258e279 100644 --- a/arch/arm/boot/dts/r8a7790-lager.dts +++ b/arch/arm/boot/dts/r8a7790-lager.dts @@ -222,6 +222,29 @@ }; }; }; + + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&adv7511_out>; + }; + }; + }; + + x2_clk: x2-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <148500000>; + }; + + x13_clk: x13-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <148500000>; + }; }; &du { @@ -229,12 +252,26 @@ pinctrl-names = "default"; status = "okay"; + clocks = <&mstp7_clks R8A7790_CLK_DU0>, + <&mstp7_clks R8A7790_CLK_DU1>, + <&mstp7_clks R8A7790_CLK_DU2>, + <&mstp7_clks R8A7790_CLK_LVDS0>, + <&mstp7_clks R8A7790_CLK_LVDS1>, + <&x13_clk>, <&x2_clk>; + clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1", + "dclkin.0", "dclkin.1"; + ports { port@0 { endpoint { remote-endpoint = <&adv7123_in>; }; }; + port@1 { + endpoint { + remote-endpoint = <&adv7511_in>; + }; + }; port@2 { lvds_connector: endpoint { }; @@ -506,6 +543,38 @@ }; }; }; + + hdmi@39 { + compatible = "adi,adv7511w"; + reg = <0x39>; + interrupt-parent = <&gpio1>; + interrupts = <15 IRQ_TYPE_EDGE_FALLING>; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7511_in: endpoint { + remote-endpoint = <&du_out_lvds0>; + }; + }; + + port@1 { + reg = <1>; + adv7511_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; }; &iic3 { @@ -513,9 +582,27 @@ pinctrl-0 = <&iic3_pins>; status = "okay"; + pmic@58 { + compatible = "dlg,da9063"; + reg = <0x58>; + interrupt-parent = <&irqc0>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + + rtc { + compatible = "dlg,da9063-rtc"; + }; + + wdt { + compatible = "dlg,da9063-watchdog"; + }; + }; + vdd_dvfs: regulator@68 { compatible = "dlg,da9210"; reg = <0x68>; + interrupt-parent = <&irqc0>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi index 4b38fc920114..4bb2f4c17321 100644 --- a/arch/arm/boot/dts/r8a7790.dtsi +++ b/arch/arm/boot/dts/r8a7790.dtsi @@ -1,6 +1,7 @@ /* * Device Tree Source for the r8a7790 SoC * + * Copyright (C) 2015 Renesas Electronics Corporation * Copyright (C) 2013-2014 Renesas Solutions Corp. * Copyright (C) 2014 Cogent Embedded Inc. * @@ -369,13 +370,6 @@ dma-channels = <13>; }; - audmapp: dma-controller@ec740000 { - compatible = "renesas,rcar-audmapp"; - #dma-cells = <1>; - - reg = <0 0xec740000 0 0x200>; - }; - i2c0: i2c@e6508000 { #address-cells = <1>; #size-cells = <0>; @@ -493,17 +487,21 @@ sdhi0: sd@ee100000 { compatible = "renesas,sdhi-r8a7790"; - reg = <0 0xee100000 0 0x200>; + reg = <0 0xee100000 0 0x328>; interrupts = <0 165 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_SDHI0>; + dmas = <&dmac1 0xcd>, <&dmac1 0xce>; + dma-names = "tx", "rx"; status = "disabled"; }; sdhi1: sd@ee120000 { compatible = "renesas,sdhi-r8a7790"; - reg = <0 0xee120000 0 0x200>; + reg = <0 0xee120000 0 0x328>; interrupts = <0 166 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_SDHI1>; + dmas = <&dmac1 0xc9>, <&dmac1 0xca>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -512,6 +510,8 @@ reg = <0 0xee140000 0 0x100>; interrupts = <0 167 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_SDHI2>; + dmas = <&dmac1 0xc1>, <&dmac1 0xc2>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -520,6 +520,8 @@ reg = <0 0xee160000 0 0x100>; interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_SDHI3>; + dmas = <&dmac1 0xd3>, <&dmac1 0xd4>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -792,6 +794,26 @@ }; }; + can0: can@e6e80000 { + compatible = "renesas,can-r8a7790"; + reg = <0 0xe6e80000 0 0x1000>; + interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7790_CLK_RCAN0>, + <&cpg_clocks R8A7790_CLK_RCAN>, <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + status = "disabled"; + }; + + can1: can@e6e88000 { + compatible = "renesas,can-r8a7790"; + reg = <0 0xe6e88000 0 0x1000>; + interrupts = <0 187 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7790_CLK_RCAN1>, + <&cpg_clocks R8A7790_CLK_RCAN>, <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + status = "disabled"; + }; + clocks { #address-cells = <2>; #size-cells = <2>; @@ -838,16 +860,34 @@ clock-output-names = "audio_clk_c"; }; + /* External USB clock - can be overridden by the board */ + usb_extal_clk: usb_extal_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; + clock-output-names = "usb_extal"; + }; + + /* External CAN clock */ + can_clk: can_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* This value must be overridden by the board. */ + clock-frequency = <0>; + clock-output-names = "can_clk"; + status = "disabled"; + }; + /* Special CPG clocks */ cpg_clocks: cpg_clocks@e6150000 { compatible = "renesas,r8a7790-cpg-clocks", "renesas,rcar-gen2-cpg-clocks"; reg = <0 0xe6150000 0 0x1000>; - clocks = <&extal_clk>; + clocks = <&extal_clk &usb_extal_clk>; #clock-cells = <1>; clock-output-names = "main", "pll0", "pll1", "pll3", "lb", "qspi", "sdh", "sd0", "sd1", - "z"; + "z", "rcan", "adsp"; }; /* Variable factor clocks */ @@ -1121,18 +1161,21 @@ mstp5_clks: mstp5_clks@e6150144 { compatible = "renesas,r8a7790-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe6150144 0 4>, <0 0xe615003c 0 4>; - clocks = <&hp_clk>, <&hp_clk>, <&extal_clk>, <&p_clk>; + clocks = <&hp_clk>, <&hp_clk>, <&cpg_clocks R8A7790_CLK_ADSP>, + <&extal_clk>, <&p_clk>; #clock-cells = <1>; clock-indices = < R8A7790_CLK_AUDIO_DMAC0 R8A7790_CLK_AUDIO_DMAC1 - R8A7790_CLK_THERMAL R8A7790_CLK_PWM + R8A7790_CLK_ADSP_MOD R8A7790_CLK_THERMAL + R8A7790_CLK_PWM >; - clock-output-names = "audmac0", "audmac1", "thermal", "pwm"; + clock-output-names = "audmac0", "audmac1", "adsp_mod", + "thermal", "pwm"; }; mstp7_clks: mstp7_clks@e615014c { compatible = "renesas,r8a7790-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe615014c 0 4>, <0 0xe61501c4 0 4>; - clocks = <&mp_clk>, <&mp_clk>, <&zs_clk>, <&zs_clk>, <&p_clk>, + clocks = <&mp_clk>, <&hp_clk>, <&zs_clk>, <&zs_clk>, <&p_clk>, <&p_clk>, <&zx_clk>, <&zx_clk>, <&zx_clk>, <&zx_clk>, <&zx_clk>; #clock-cells = <1>; @@ -1410,7 +1453,10 @@ reg = <0 0xec500000 0 0x1000>, /* SCU */ <0 0xec5a0000 0 0x100>, /* ADG */ <0 0xec540000 0 0x1000>, /* SSIU */ - <0 0xec541000 0 0x1280>; /* SSI */ + <0 0xec541000 0 0x1280>, /* SSI */ + <0 0xec740000 0 0x200>; /* Audio DMAC peri peri*/ + reg-names = "scu", "adg", "ssiu", "ssi", "audmapp"; + clocks = <&mstp10_clks R8A7790_CLK_SSI_ALL>, <&mstp10_clks R8A7790_CLK_SSI9>, <&mstp10_clks R8A7790_CLK_SSI8>, <&mstp10_clks R8A7790_CLK_SSI7>, <&mstp10_clks R8A7790_CLK_SSI6>, @@ -1435,34 +1481,171 @@ status = "disabled"; rcar_sound,dvc { - dvc0: dvc@0 { }; - dvc1: dvc@1 { }; + dvc0: dvc@0 { + dmas = <&audma0 0xbc>; + dma-names = "tx"; + }; + dvc1: dvc@1 { + dmas = <&audma0 0xbe>; + dma-names = "tx"; + }; }; rcar_sound,src { - src0: src@0 { interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; }; - src1: src@1 { interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>; }; - src2: src@2 { interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>; }; - src3: src@3 { interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>; }; - src4: src@4 { interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>; }; - src5: src@5 { interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>; }; - src6: src@6 { interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>; }; - src7: src@7 { interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>; }; - src8: src@8 { interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>; }; - src9: src@9 { interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>; }; + src0: src@0 { + interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x85>, <&audma1 0x9a>; + dma-names = "rx", "tx"; + }; + src1: src@1 { + interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x87>, <&audma1 0x9c>; + dma-names = "rx", "tx"; + }; + src2: src@2 { + interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x89>, <&audma1 0x9e>; + dma-names = "rx", "tx"; + }; + src3: src@3 { + interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8b>, <&audma1 0xa0>; + dma-names = "rx", "tx"; + }; + src4: src@4 { + interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8d>, <&audma1 0xb0>; + dma-names = "rx", "tx"; + }; + src5: src@5 { + interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8f>, <&audma1 0xb2>; + dma-names = "rx", "tx"; + }; + src6: src@6 { + interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x91>, <&audma1 0xb4>; + dma-names = "rx", "tx"; + }; + src7: src@7 { + interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x93>, <&audma1 0xb6>; + dma-names = "rx", "tx"; + }; + src8: src@8 { + interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x95>, <&audma1 0xb8>; + dma-names = "rx", "tx"; + }; + src9: src@9 { + interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x97>, <&audma1 0xba>; + dma-names = "rx", "tx"; + }; }; rcar_sound,ssi { - ssi0: ssi@0 { interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; }; - ssi1: ssi@1 { interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; }; - ssi2: ssi@2 { interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; }; - ssi3: ssi@3 { interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; }; - ssi4: ssi@4 { interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; }; - ssi5: ssi@5 { interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; }; - ssi6: ssi@6 { interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; }; - ssi7: ssi@7 { interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; }; - ssi8: ssi@8 { interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; }; - ssi9: ssi@9 { interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; }; + ssi0: ssi@0 { + interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi1: ssi@1 { + interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi2: ssi@2 { + interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi3: ssi@3 { + interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi4: ssi@4 { + interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi5: ssi@5 { + interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi6: ssi@6 { + interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi7: ssi@7 { + interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi8: ssi@8 { + interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi9: ssi@9 { + interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>; + dma-names = "rx", "tx", "rxu", "txu"; + }; }; }; + + ipmmu_sy0: mmu@e6280000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6280000 0 0x1000>; + interrupts = <0 223 IRQ_TYPE_LEVEL_HIGH>, + <0 224 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_sy1: mmu@e6290000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6290000 0 0x1000>; + interrupts = <0 225 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_ds: mmu@e6740000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6740000 0 0x1000>; + interrupts = <0 198 IRQ_TYPE_LEVEL_HIGH>, + <0 199 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_mp: mmu@ec680000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xec680000 0 0x1000>; + interrupts = <0 226 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_mx: mmu@fe951000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xfe951000 0 0x1000>; + interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, + <0 221 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_rt: mmu@ffc80000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xffc80000 0 0x1000>; + interrupts = <0 307 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; }; diff --git a/arch/arm/boot/dts/r8a7791-henninger.dts b/arch/arm/boot/dts/r8a7791-henninger.dts index d2ebf11f9881..e33e4047b0b0 100644 --- a/arch/arm/boot/dts/r8a7791-henninger.dts +++ b/arch/arm/boot/dts/r8a7791-henninger.dts @@ -141,6 +141,11 @@ renesas,groups = "vin0_data8", "vin0_clk"; renesas,function = "vin0"; }; + + can0_pins: can0 { + renesas,groups = "can0_data"; + renesas,function = "can0"; + }; }; &scif0 { @@ -307,3 +312,9 @@ }; }; }; + +&can0 { + pinctrl-0 = <&can0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts index a3c27807f6c5..824ddab9c3ad 100644 --- a/arch/arm/boot/dts/r8a7791-koelsch.dts +++ b/arch/arm/boot/dts/r8a7791-koelsch.dts @@ -258,6 +258,29 @@ system-clock-frequency = <11289600>; }; }; + + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&adv7511_out>; + }; + }; + }; + + x2_clk: x2-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <148500000>; + }; + + x13_clk: x13-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <148500000>; + }; }; &du { @@ -265,7 +288,19 @@ pinctrl-names = "default"; status = "okay"; + clocks = <&mstp7_clks R8A7791_CLK_DU0>, + <&mstp7_clks R8A7791_CLK_DU1>, + <&mstp7_clks R8A7791_CLK_LVDS0>, + <&x13_clk>, <&x2_clk>; + clock-names = "du.0", "du.1", "lvds.0", + "dclkin.0", "dclkin.1"; + ports { + port@0 { + endpoint { + remote-endpoint = <&adv7511_in>; + }; + }; port@1 { lvds_connector: endpoint { }; @@ -284,7 +319,7 @@ }; du_pins: du { - renesas,groups = "du_rgb666", "du_sync", "du_clk_out_0"; + renesas,groups = "du_rgb666", "du_sync", "du_disp", "du_clk_out_0"; renesas,function = "du"; }; @@ -506,6 +541,38 @@ }; }; + hdmi@39 { + compatible = "adi,adv7511w"; + reg = <0x39>; + interrupt-parent = <&gpio3>; + interrupts = <29 IRQ_TYPE_LEVEL_LOW>; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7511_in: endpoint { + remote-endpoint = <&du_out_rgb>; + }; + }; + + port@1 { + reg = <1>; + adv7511_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; + eeprom@50 { compatible = "renesas,24c02"; reg = <0x50>; @@ -517,9 +584,27 @@ status = "okay"; clock-frequency = <100000>; + pmic@58 { + compatible = "dlg,da9063"; + reg = <0x58>; + interrupt-parent = <&irqc0>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + + rtc { + compatible = "dlg,da9063-rtc"; + }; + + wdt { + compatible = "dlg,da9063-watchdog"; + }; + }; + vdd_dvfs: regulator@68 { compatible = "dlg,da9210"; reg = <0x68>; + interrupt-parent = <&irqc0>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index e35812a0d8d4..4696062f6dde 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -1,7 +1,7 @@ /* * Device Tree Source for the r8a7791 SoC * - * Copyright (C) 2013-2014 Renesas Electronics Corporation + * Copyright (C) 2013-2015 Renesas Electronics Corporation * Copyright (C) 2013-2014 Renesas Solutions Corp. * Copyright (C) 2014 Cogent Embedded Inc. * @@ -357,13 +357,6 @@ dma-channels = <13>; }; - audmapp: dma-controller@ec740000 { - compatible = "renesas,rcar-audmapp"; - #dma-cells = <1>; - - reg = <0 0xec740000 0 0x200>; - }; - /* The memory map in the User's Manual maps the cores to bus numbers */ i2c0: i2c@e6508000 { #address-cells = <1>; @@ -482,9 +475,11 @@ sdhi0: sd@ee100000 { compatible = "renesas,sdhi-r8a7791"; - reg = <0 0xee100000 0 0x200>; + reg = <0 0xee100000 0 0x328>; interrupts = <0 165 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7791_CLK_SDHI0>; + dmas = <&dmac1 0xcd>, <&dmac1 0xce>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -493,6 +488,8 @@ reg = <0 0xee140000 0 0x100>; interrupts = <0 167 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7791_CLK_SDHI1>; + dmas = <&dmac1 0xc1>, <&dmac1 0xc2>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -501,6 +498,8 @@ reg = <0 0xee160000 0 0x100>; interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7791_CLK_SDHI2>; + dmas = <&dmac1 0xd3>, <&dmac1 0xd4>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -816,6 +815,26 @@ }; }; + can0: can@e6e80000 { + compatible = "renesas,can-r8a7791"; + reg = <0 0xe6e80000 0 0x1000>; + interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_RCAN0>, + <&cpg_clocks R8A7791_CLK_RCAN>, <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + status = "disabled"; + }; + + can1: can@e6e88000 { + compatible = "renesas,can-r8a7791"; + reg = <0 0xe6e88000 0 0x1000>; + interrupts = <0 187 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_RCAN1>, + <&cpg_clocks R8A7791_CLK_RCAN>, <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + status = "disabled"; + }; + clocks { #address-cells = <2>; #size-cells = <2>; @@ -862,31 +881,50 @@ status = "disabled"; }; + /* External USB clock - can be overridden by the board */ + usb_extal_clk: usb_extal_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; + clock-output-names = "usb_extal"; + }; + + /* External CAN clock */ + can_clk: can_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* This value must be overridden by the board. */ + clock-frequency = <0>; + clock-output-names = "can_clk"; + status = "disabled"; + }; + /* Special CPG clocks */ cpg_clocks: cpg_clocks@e6150000 { compatible = "renesas,r8a7791-cpg-clocks", "renesas,rcar-gen2-cpg-clocks"; reg = <0 0xe6150000 0 0x1000>; - clocks = <&extal_clk>; + clocks = <&extal_clk &usb_extal_clk>; #clock-cells = <1>; clock-output-names = "main", "pll0", "pll1", "pll3", - "lb", "qspi", "sdh", "sd0", "z"; + "lb", "qspi", "sdh", "sd0", "z", + "rcan", "adsp"; }; /* Variable factor clocks */ - sd1_clk: sd2_clk@e6150078 { + sd2_clk: sd2_clk@e6150078 { compatible = "renesas,r8a7791-div6-clock", "renesas,cpg-div6-clock"; reg = <0 0xe6150078 0 4>; clocks = <&pll1_div2_clk>; #clock-cells = <0>; - clock-output-names = "sd1"; + clock-output-names = "sd2"; }; - sd2_clk: sd3_clk@e615026c { + sd3_clk: sd3_clk@e615026c { compatible = "renesas,r8a7791-div6-clock", "renesas,cpg-div6-clock"; reg = <0 0xe615026c 0 4>; clocks = <&pll1_div2_clk>; #clock-cells = <0>; - clock-output-names = "sd2"; + clock-output-names = "sd3"; }; mmc0_clk: mmc0_clk@e6150240 { compatible = "renesas,r8a7791-div6-clock", "renesas,cpg-div6-clock"; @@ -1107,7 +1145,7 @@ mstp3_clks: mstp3_clks@e615013c { compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe615013c 0 4>, <0 0xe6150048 0 4>; - clocks = <&cp_clk>, <&sd2_clk>, <&sd1_clk>, <&cpg_clocks R8A7791_CLK_SD0>, + clocks = <&cp_clk>, <&sd3_clk>, <&sd2_clk>, <&cpg_clocks R8A7791_CLK_SD0>, <&mmc0_clk>, <&hp_clk>, <&mp_clk>, <&hp_clk>, <&mp_clk>, <&rclk_clk>, <&hp_clk>, <&hp_clk>; #clock-cells = <1>; @@ -1125,18 +1163,21 @@ mstp5_clks: mstp5_clks@e6150144 { compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe6150144 0 4>, <0 0xe615003c 0 4>; - clocks = <&hp_clk>, <&hp_clk>, <&extal_clk>, <&p_clk>; + clocks = <&hp_clk>, <&hp_clk>, <&cpg_clocks R8A7791_CLK_ADSP>, + <&extal_clk>, <&p_clk>; #clock-cells = <1>; clock-indices = < R8A7791_CLK_AUDIO_DMAC0 R8A7791_CLK_AUDIO_DMAC1 - R8A7791_CLK_THERMAL R8A7791_CLK_PWM + R8A7791_CLK_ADSP_MOD R8A7791_CLK_THERMAL + R8A7791_CLK_PWM >; - clock-output-names = "audmac0", "audmac1", "thermal", "pwm"; + clock-output-names = "audmac0", "audmac1", "adsp_mod", + "thermal", "pwm"; }; mstp7_clks: mstp7_clks@e615014c { compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe615014c 0 4>, <0 0xe61501c4 0 4>; - clocks = <&mp_clk>, <&mp_clk>, <&zs_clk>, <&p_clk>, <&p_clk>, <&zs_clk>, + clocks = <&mp_clk>, <&hp_clk>, <&zs_clk>, <&p_clk>, <&p_clk>, <&zs_clk>, <&zs_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&zx_clk>, <&zx_clk>, <&zx_clk>; #clock-cells = <1>; @@ -1154,7 +1195,7 @@ mstp8_clks: mstp8_clks@e6150990 { compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe6150990 0 4>, <0 0xe61509a0 0 4>; - clocks = <&zg_clk>, <&hp_clk>, <&zg_clk>, <&zg_clk>, + clocks = <&zx_clk>, <&hp_clk>, <&zg_clk>, <&zg_clk>, <&zg_clk>, <&p_clk>, <&zs_clk>, <&zs_clk>; #clock-cells = <1>; clock-indices = < @@ -1384,6 +1425,66 @@ status = "disabled"; }; + ipmmu_sy0: mmu@e6280000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6280000 0 0x1000>; + interrupts = <0 223 IRQ_TYPE_LEVEL_HIGH>, + <0 224 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_sy1: mmu@e6290000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6290000 0 0x1000>; + interrupts = <0 225 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_ds: mmu@e6740000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6740000 0 0x1000>; + interrupts = <0 198 IRQ_TYPE_LEVEL_HIGH>, + <0 199 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_mp: mmu@ec680000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xec680000 0 0x1000>; + interrupts = <0 226 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_mx: mmu@fe951000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xfe951000 0 0x1000>; + interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, + <0 221 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_rt: mmu@ffc80000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xffc80000 0 0x1000>; + interrupts = <0 307 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_gp: mmu@e62a0000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe62a0000 0 0x1000>; + interrupts = <0 260 IRQ_TYPE_LEVEL_HIGH>, + <0 261 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + rcar_sound: rcar_sound@ec500000 { /* * #sound-dai-cells is required @@ -1395,7 +1496,10 @@ reg = <0 0xec500000 0 0x1000>, /* SCU */ <0 0xec5a0000 0 0x100>, /* ADG */ <0 0xec540000 0 0x1000>, /* SSIU */ - <0 0xec541000 0 0x1280>; /* SSI */ + <0 0xec541000 0 0x1280>, /* SSI */ + <0 0xec740000 0 0x200>; /* Audio DMAC peri peri*/ + reg-names = "scu", "adg", "ssiu", "ssi", "audmapp"; + clocks = <&mstp10_clks R8A7791_CLK_SSI_ALL>, <&mstp10_clks R8A7791_CLK_SSI9>, <&mstp10_clks R8A7791_CLK_SSI8>, <&mstp10_clks R8A7791_CLK_SSI7>, <&mstp10_clks R8A7791_CLK_SSI6>, @@ -1420,34 +1524,120 @@ status = "disabled"; rcar_sound,dvc { - dvc0: dvc@0 { }; - dvc1: dvc@1 { }; + dvc0: dvc@0 { + dmas = <&audma0 0xbc>; + dma-names = "tx"; + }; + dvc1: dvc@1 { + dmas = <&audma0 0xbe>; + dma-names = "tx"; + }; }; rcar_sound,src { - src0: src@0 { interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; }; - src1: src@1 { interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>; }; - src2: src@2 { interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>; }; - src3: src@3 { interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>; }; - src4: src@4 { interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>; }; - src5: src@5 { interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>; }; - src6: src@6 { interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>; }; - src7: src@7 { interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>; }; - src8: src@8 { interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>; }; - src9: src@9 { interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>; }; + src0: src@0 { + interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x85>, <&audma1 0x9a>; + dma-names = "rx", "tx"; + }; + src1: src@1 { + interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x87>, <&audma1 0x9c>; + dma-names = "rx", "tx"; + }; + src2: src@2 { + interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x89>, <&audma1 0x9e>; + dma-names = "rx", "tx"; + }; + src3: src@3 { + interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8b>, <&audma1 0xa0>; + dma-names = "rx", "tx"; + }; + src4: src@4 { + interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8d>, <&audma1 0xb0>; + dma-names = "rx", "tx"; + }; + src5: src@5 { + interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8f>, <&audma1 0xb2>; + dma-names = "rx", "tx"; + }; + src6: src@6 { + interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x91>, <&audma1 0xb4>; + dma-names = "rx", "tx"; + }; + src7: src@7 { + interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x93>, <&audma1 0xb6>; + dma-names = "rx", "tx"; + }; + src8: src@8 { + interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x95>, <&audma1 0xb8>; + dma-names = "rx", "tx"; + }; + src9: src@9 { + interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x97>, <&audma1 0xba>; + dma-names = "rx", "tx"; + }; }; rcar_sound,ssi { - ssi0: ssi@0 { interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; }; - ssi1: ssi@1 { interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; }; - ssi2: ssi@2 { interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; }; - ssi3: ssi@3 { interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; }; - ssi4: ssi@4 { interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; }; - ssi5: ssi@5 { interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; }; - ssi6: ssi@6 { interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; }; - ssi7: ssi@7 { interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; }; - ssi8: ssi@8 { interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; }; - ssi9: ssi@9 { interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; }; + ssi0: ssi@0 { + interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi1: ssi@1 { + interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi2: ssi@2 { + interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi3: ssi@3 { + interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi4: ssi@4 { + interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi5: ssi@5 { + interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi6: ssi@6 { + interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi7: ssi@7 { + interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi8: ssi@8 { + interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi9: ssi@9 { + interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>; + dma-names = "rx", "tx", "rxu", "txu"; + }; }; }; }; diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts index 0d848e605071..928cfa641475 100644 --- a/arch/arm/boot/dts/r8a7794-alt.dts +++ b/arch/arm/boot/dts/r8a7794-alt.dts @@ -43,6 +43,19 @@ status = "okay"; }; +ðer { + phy-handle = <&phy1>; + renesas,ether-link-active-low; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&irqc0>; + interrupts = <8 IRQ_TYPE_LEVEL_LOW>; + micrel,led-mode = <1>; + }; +}; + &scif2 { status = "okay"; }; diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi index 8f78da5ef10b..7a3ffa51a8bf 100644 --- a/arch/arm/boot/dts/r8a7794.dtsi +++ b/arch/arm/boot/dts/r8a7794.dtsi @@ -107,6 +107,66 @@ <0 17 IRQ_TYPE_LEVEL_HIGH>; }; + dmac0: dma-controller@e6700000 { + compatible = "renesas,rcar-dmac"; + reg = <0 0xe6700000 0 0x20000>; + interrupts = <0 197 IRQ_TYPE_LEVEL_HIGH + 0 200 IRQ_TYPE_LEVEL_HIGH + 0 201 IRQ_TYPE_LEVEL_HIGH + 0 202 IRQ_TYPE_LEVEL_HIGH + 0 203 IRQ_TYPE_LEVEL_HIGH + 0 204 IRQ_TYPE_LEVEL_HIGH + 0 205 IRQ_TYPE_LEVEL_HIGH + 0 206 IRQ_TYPE_LEVEL_HIGH + 0 207 IRQ_TYPE_LEVEL_HIGH + 0 208 IRQ_TYPE_LEVEL_HIGH + 0 209 IRQ_TYPE_LEVEL_HIGH + 0 210 IRQ_TYPE_LEVEL_HIGH + 0 211 IRQ_TYPE_LEVEL_HIGH + 0 212 IRQ_TYPE_LEVEL_HIGH + 0 213 IRQ_TYPE_LEVEL_HIGH + 0 214 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14"; + clocks = <&mstp2_clks R8A7794_CLK_SYS_DMAC0>; + clock-names = "fck"; + #dma-cells = <1>; + dma-channels = <15>; + }; + + dmac1: dma-controller@e6720000 { + compatible = "renesas,rcar-dmac"; + reg = <0 0xe6720000 0 0x20000>; + interrupts = <0 220 IRQ_TYPE_LEVEL_HIGH + 0 216 IRQ_TYPE_LEVEL_HIGH + 0 217 IRQ_TYPE_LEVEL_HIGH + 0 218 IRQ_TYPE_LEVEL_HIGH + 0 219 IRQ_TYPE_LEVEL_HIGH + 0 308 IRQ_TYPE_LEVEL_HIGH + 0 309 IRQ_TYPE_LEVEL_HIGH + 0 310 IRQ_TYPE_LEVEL_HIGH + 0 311 IRQ_TYPE_LEVEL_HIGH + 0 312 IRQ_TYPE_LEVEL_HIGH + 0 313 IRQ_TYPE_LEVEL_HIGH + 0 314 IRQ_TYPE_LEVEL_HIGH + 0 315 IRQ_TYPE_LEVEL_HIGH + 0 316 IRQ_TYPE_LEVEL_HIGH + 0 317 IRQ_TYPE_LEVEL_HIGH + 0 318 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14"; + clocks = <&mstp2_clks R8A7794_CLK_SYS_DMAC1>; + clock-names = "fck"; + #dma-cells = <1>; + dma-channels = <15>; + }; + scifa0: serial@e6c40000 { compatible = "renesas,scifa-r8a7794", "renesas,scifa"; reg = <0 0xe6c40000 0 64>; @@ -269,6 +329,41 @@ status = "disabled"; }; + ether: ethernet@ee700000 { + compatible = "renesas,ether-r8a7794"; + reg = <0 0xee700000 0 0x400>; + interrupts = <0 162 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7794_CLK_ETHER>; + phy-mode = "rmii"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + sdhi0: sd@ee100000 { + compatible = "renesas,sdhi-r8a7794"; + reg = <0 0xee100000 0 0x200>; + interrupts = <0 165 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7794_CLK_SDHI0>; + status = "disabled"; + }; + + sdhi1: sd@ee140000 { + compatible = "renesas,sdhi-r8a7794"; + reg = <0 0xee140000 0 0x100>; + interrupts = <0 167 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7794_CLK_SDHI1>; + status = "disabled"; + }; + + sdhi2: sd@ee160000 { + compatible = "renesas,sdhi-r8a7794"; + reg = <0 0xee160000 0 0x100>; + interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7794_CLK_SDHI2>; + status = "disabled"; + }; + clocks { #address-cells = <2>; #size-cells = <2>; @@ -294,19 +389,19 @@ "lb", "qspi", "sdh", "sd0", "z"; }; /* Variable factor clocks */ - sd1_clk: sd2_clk@e6150078 { + sd2_clk: sd2_clk@e6150078 { compatible = "renesas,r8a7794-div6-clock", "renesas,cpg-div6-clock"; reg = <0 0xe6150078 0 4>; clocks = <&pll1_div2_clk>; #clock-cells = <0>; - clock-output-names = "sd1"; + clock-output-names = "sd2"; }; - sd2_clk: sd3_clk@e615007c { + sd3_clk: sd3_clk@e615026c { compatible = "renesas,r8a7794-div6-clock", "renesas,cpg-div6-clock"; - reg = <0 0xe615007c 0 4>; + reg = <0 0xe615026c 0 4>; clocks = <&pll1_div2_clk>; #clock-cells = <0>; - clock-output-names = "sd2"; + clock-output-names = "sd3"; }; mmc0_clk: mmc0_clk@e6150240 { compatible = "renesas,r8a7794-div6-clock", "renesas,cpg-div6-clock"; @@ -518,7 +613,7 @@ mstp3_clks: mstp3_clks@e615013c { compatible = "renesas,r8a7794-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe615013c 0 4>, <0 0xe6150048 0 4>; - clocks = <&sd2_clk>, <&sd1_clk>, <&cpg_clocks R8A7794_CLK_SD0>, + clocks = <&sd3_clk>, <&sd2_clk>, <&cpg_clocks R8A7794_CLK_SD0>, <&mmc0_clk>, <&rclk_clk>, <&hp_clk>, <&hp_clk>; #clock-cells = <1>; clock-indices = < @@ -585,4 +680,54 @@ clock-output-names = "scifa3", "scifa4", "scifa5"; }; }; + + ipmmu_sy0: mmu@e6280000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6280000 0 0x1000>; + interrupts = <0 223 IRQ_TYPE_LEVEL_HIGH>, + <0 224 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_sy1: mmu@e6290000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6290000 0 0x1000>; + interrupts = <0 225 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_ds: mmu@e6740000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6740000 0 0x1000>; + interrupts = <0 198 IRQ_TYPE_LEVEL_HIGH>, + <0 199 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + }; + + ipmmu_mp: mmu@ec680000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xec680000 0 0x1000>; + interrupts = <0 226 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_mx: mmu@fe951000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xfe951000 0 0x1000>; + interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, + <0 221 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + }; + + ipmmu_gp: mmu@e62a0000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe62a0000 0 0x1000>; + interrupts = <0 260 IRQ_TYPE_LEVEL_HIGH>, + <0 261 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; }; diff --git a/arch/arm/boot/dts/rk3188-radxarock.dts b/arch/arm/boot/dts/rk3188-radxarock.dts index 9a09579b8309..bdf85701987d 100644 --- a/arch/arm/boot/dts/rk3188-radxarock.dts +++ b/arch/arm/boot/dts/rk3188-radxarock.dts @@ -103,6 +103,14 @@ regulator-always-on; regulator-boot-on; }; + + vsys: vsys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vsys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; }; &emac { @@ -148,6 +156,14 @@ pinctrl-names = "default"; pinctrl-0 = <&act8846_dvs0_ctl>; + vp1-supply = <&vsys>; + vp2-supply = <&vsys>; + vp3-supply = <&vsys>; + vp4-supply = <&vsys>; + inl1-supply = <&vcc_io>; + inl2-supply = <&vsys>; + inl3-supply = <&vsys>; + regulators { vcc_ddr: REG1 { regulator-name = "VCC_DDR"; diff --git a/arch/arm/boot/dts/rk3288-evb-act8846.dts b/arch/arm/boot/dts/rk3288-evb-act8846.dts index d7b8bbc0c25f..1687e8336994 100644 --- a/arch/arm/boot/dts/rk3288-evb-act8846.dts +++ b/arch/arm/boot/dts/rk3288-evb-act8846.dts @@ -33,6 +33,7 @@ regulator-max-microvolt = <1350000>; regulator-always-on; regulator-boot-on; + vin-supply = <&vcc_sys>; }; vdd_gpu: syr828@41 { @@ -43,6 +44,7 @@ regulator-min-microvolt = <850000>; regulator-max-microvolt = <1350000>; regulator-always-on; + vin-supply = <&vcc_sys>; }; hym8563@51 { @@ -64,6 +66,14 @@ reg = <0x5a>; status = "okay"; + vp1-supply = <&vcc_sys>; + vp2-supply = <&vcc_sys>; + vp3-supply = <&vcc_sys>; + vp4-supply = <&vcc_sys>; + inl1-supply = <&vcc_io>; + inl2-supply = <&vcc_sys>; + inl3-supply = <&vcc_20>; + regulators { vcc_ddr: REG1 { regulator-name = "VCC_DDR"; diff --git a/arch/arm/boot/dts/rk3288-evb-rk808.dts b/arch/arm/boot/dts/rk3288-evb-rk808.dts index a1c294bf7fed..f62ea78754a9 100644 --- a/arch/arm/boot/dts/rk3288-evb-rk808.dts +++ b/arch/arm/boot/dts/rk3288-evb-rk808.dts @@ -43,9 +43,16 @@ #clock-cells = <1>; clock-output-names = "xin32k", "rk808-clkout2"; + vcc1-supply = <&vcc_sys>; + vcc2-supply = <&vcc_sys>; + vcc3-supply = <&vcc_sys>; + vcc4-supply = <&vcc_sys>; + vcc6-supply = <&vcc_sys>; + vcc7-supply = <&vcc_sys>; vcc8-supply = <&vcc_18>; vcc9-supply = <&vcc_io>; vcc10-supply = <&vcc_io>; + vcc11-supply = <&vcc_sys>; vcc12-supply = <&vcc_io>; vddio-supply = <&vccio_pmu>; diff --git a/arch/arm/boot/dts/rk3288-evb.dtsi b/arch/arm/boot/dts/rk3288-evb.dtsi index 5e895a514a0b..4a457518d861 100644 --- a/arch/arm/boot/dts/rk3288-evb.dtsi +++ b/arch/arm/boot/dts/rk3288-evb.dtsi @@ -103,6 +103,15 @@ regulator-always-on; regulator-boot-on; }; + + vcc_sys: vsys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; }; &emmc { @@ -238,6 +247,10 @@ }; }; +&usbphy { + status = "okay"; +}; + &usb_host0_ehci { status = "okay"; }; diff --git a/arch/arm/boot/dts/rk3288-firefly.dtsi b/arch/arm/boot/dts/rk3288-firefly.dtsi index e6f873abbe0d..b54dd78580c1 100644 --- a/arch/arm/boot/dts/rk3288-firefly.dtsi +++ b/arch/arm/boot/dts/rk3288-firefly.dtsi @@ -179,6 +179,22 @@ status = "okay"; }; +&gmac { + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + clock_in_out = "input"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>; + phy-supply = <&vcc_lan>; + phy-mode = "rgmii"; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>; + tx_delay = <0x30>; + rx_delay = <0x10>; + status = "ok"; +}; + &hdmi { ddc-i2c-bus = <&i2c5>; status = "okay"; @@ -459,6 +475,10 @@ status = "okay"; }; +&usbphy { + status = "okay"; +}; + &usb_host1 { pinctrl-names = "default"; pinctrl-0 = <&usbhub_rst>; diff --git a/arch/arm/boot/dts/rk3288-popmetal.dts b/arch/arm/boot/dts/rk3288-popmetal.dts new file mode 100644 index 000000000000..d081f0e0da36 --- /dev/null +++ b/arch/arm/boot/dts/rk3288-popmetal.dts @@ -0,0 +1,447 @@ +/* + * Copyright (c) 2014, 2015 Andy Yan + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "rk3288.dtsi" + +/ { + model = "PopMetal-RK3288"; + compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; + + memory{ + reg = <0 0x80000000>; + }; + + ext_gmac: external-gmac-clock { + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "ext_gmac"; + #clock-cells = <0>; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&pwrbtn>; + + button@0 { + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + linux,code = <116>; + label = "GPIO Key Power"; + linux,input-type = <1>; + gpio-key,wakeup = <1>; + debounce-interval = <100>; + }; + }; + + ir: ir-receiver { + compatible = "gpio-ir-receiver"; + gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ir_int>; + }; + + vcc_sys: vsys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; +}; + +&cpu0 { + cpu0-supply = <&vdd_cpu>; +}; + +&emmc { + broken-cd; + bus-width = <8>; + cap-mmc-highspeed; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>; + status = "okay"; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + card-detect-delay = <200>; + disable-wp; /* wp not hooked up */ + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; + status = "okay"; +}; + +&gmac { + phy-supply = <&vcc_lan>; + phy-mode = "rgmii"; + clock_in_out = "input"; + snps,reset-gpio = <&gpio4 7 0>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 1000000>; + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + tx_delay = <0x30>; + rx_delay = <0x10>; + status = "ok"; +}; + +&hdmi { + ddc-i2c-bus = <&i2c5>; + status = "okay"; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <400000>; + + rk808: pmic@1b { + compatible = "rockchip,rk808"; + reg = <0x1b>; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int &global_pwroff>; + rockchip,system-power-controller; + wakeup-source; + #clock-cells = <1>; + clock-output-names = "xin32k", "rk808-clkout2"; + + vcc1-supply = <&vcc_sys>; + vcc2-supply = <&vcc_sys>; + vcc3-supply = <&vcc_sys>; + vcc4-supply = <&vcc_sys>; + vcc6-supply = <&vcc_sys>; + vcc7-supply = <&vcc_sys>; + vcc8-supply = <&vcc_18>; + vcc9-supply = <&vcc_io>; + vcc10-supply = <&vcc_io>; + vcc11-supply = <&vcc_sys>; + vcc12-supply = <&vcc_io>; + vddio-supply = <&vcc_io>; + + regulators { + vdd_cpu: DCDC_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1350000>; + regulator-name = "vdd_arm"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_gpu: DCDC_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd_gpu"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_ddr"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_io: DCDC_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_io"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_lan: LDO_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_lan"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vccio_sd: LDO_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_10: LDO_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd_10"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc18_lcd: LDO_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc18_lcd"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + ldo5: LDO_REG5 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "ldo5"; + }; + + vdd10_lcd: LDO_REG6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd10_lcd"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc_18: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_18"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcca_codec: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcca_codec"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_wl: SWITCH_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_wl"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_lcd: SWITCH_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_lcd"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + }; + }; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + ak8963: ak8963@0d { + compatible = "asahi-kasei,ak8975"; + reg = <0x0d>; + interrupt-parent = <&gpio8>; + interrupts = <1 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&comp_int>; + }; + + l3g4200d: l3g4200d@68 { + compatible = "st,l3g4200d-gyro"; + st,drdy-int-pin = <2>; + reg = <0x6b>; + }; + + mma8452: mma8452@1d { + compatible = "fsl,mma8452"; + reg = <0x1d>; + interrupt-parent = <&gpio8>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&gsensor_int>; + }; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +&i2c4 { + status = "okay"; +}; + +&i2c5 { + status = "okay"; +}; + +&pinctrl { + ak8963 { + comp_int: comp-int { + rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + buttons { + pwrbtn: pwrbtn { + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + ir { + ir_int: ir-int { + rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + mma8452 { + gsensor_int: gsensor-int { + rockchip,pins = <8 0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + pmic { + pmic_int: pmic-int { + rockchip,pins = ; + }; + }; +}; + +&vopb { + status = "okay"; +}; + +&vopb_mmu { + status = "okay"; +}; + +&vopl { + status = "okay"; +}; + +&vopl_mmu { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index eccc78d3220b..165968d51d8f 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -420,6 +420,8 @@ interrupts = ; clocks = <&cru HCLK_USBHOST0>; clock-names = "usbhost"; + phys = <&usbphy1>; + phy-names = "usb"; status = "disabled"; }; @@ -432,6 +434,8 @@ interrupts = ; clocks = <&cru HCLK_USBHOST1>; clock-names = "otg"; + phys = <&usbphy2>; + phy-names = "usb2-phy"; status = "disabled"; }; @@ -442,6 +446,8 @@ interrupts = ; clocks = <&cru HCLK_OTG0>; clock-names = "otg"; + phys = <&usbphy0>; + phy-names = "usb2-phy"; status = "disabled"; }; @@ -698,6 +704,35 @@ interrupts = ; }; + usbphy: phy { + compatible = "rockchip,rk3288-usb-phy"; + rockchip,grf = <&grf>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + usbphy0: usb-phy0 { + #phy-cells = <0>; + reg = <0x320>; + clocks = <&cru SCLK_OTGPHY0>; + clock-names = "phyclk"; + }; + + usbphy1: usb-phy1 { + #phy-cells = <0>; + reg = <0x334>; + clocks = <&cru SCLK_OTGPHY1>; + clock-names = "phyclk"; + }; + + usbphy2: usb-phy2 { + #phy-cells = <0>; + reg = <0x348>; + clocks = <&cru SCLK_OTGPHY2>; + clock-names = "phyclk"; + }; + }; + pinctrl: pinctrl { compatible = "rockchip,rk3288-pinctrl"; rockchip,grf = <&grf>; diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi index 367af53c1b84..57ab8587f7b9 100644 --- a/arch/arm/boot/dts/sama5d3.dtsi +++ b/arch/arm/boot/dts/sama5d3.dtsi @@ -26,6 +26,7 @@ serial2 = &usart1; serial3 = &usart2; serial4 = &usart3; + serial5 = &uart0; gpio0 = &pioA; gpio1 = &pioB; gpio2 = &pioC; @@ -206,6 +207,17 @@ status = "disabled"; }; + uart0: serial@f0024000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xf0024000 0x100>; + interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart0>; + clocks = <&uart0_clk>; + clock-names = "usart"; + status = "disabled"; + }; + pwm0: pwm@f002c000 { compatible = "atmel,sama5d3-pwm"; reg = <0xf002c000 0x300>; @@ -439,7 +451,7 @@ }; dbgu: serial@ffffee00 { - compatible = "atmel,at91sam9260-usart"; + compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"; reg = <0xffffee00 0x200>; interrupts = <2 IRQ_TYPE_LEVEL_HIGH 7>; dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(13)>, @@ -764,6 +776,22 @@ }; }; + uart0 { + pinctrl_uart0: uart0-0 { + atmel,pins = + ; /* conflicts with ISI_PCK */ + }; + }; + + uart1 { + pinctrl_uart1: uart1-0 { + atmel,pins = + ; /* conflicts with TWCK0, ISI_HSYNC */ + }; + }; + usart0 { pinctrl_usart0: usart0-0 { atmel,pins = @@ -1098,6 +1126,12 @@ atmel,clk-output-range = <0 66000000>; }; + uart0_clk: uart0_clk { + #clock-cells = <0>; + reg = <16>; + atmel,clk-output-range = <0 66000000>; + }; + twi0_clk: twi0_clk { reg = <18>; #clock-cells = <0>; diff --git a/arch/arm/boot/dts/sama5d35ek.dts b/arch/arm/boot/dts/sama5d35ek.dts index 9089c7c6cea8..d9a9aca1ccfd 100644 --- a/arch/arm/boot/dts/sama5d35ek.dts +++ b/arch/arm/boot/dts/sama5d35ek.dts @@ -44,8 +44,6 @@ gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; pb_user1 { label = "pb_user1"; diff --git a/arch/arm/boot/dts/sama5d3_can.dtsi b/arch/arm/boot/dts/sama5d3_can.dtsi index eaf41451ad0c..c5a3772741bf 100644 --- a/arch/arm/boot/dts/sama5d3_can.dtsi +++ b/arch/arm/boot/dts/sama5d3_can.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_can.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_can.dtsi - Device Tree Include file for SAMA5D3 SoC with * CAN support * * Copyright (C) 2013 Boris BREZILLON diff --git a/arch/arm/boot/dts/sama5d3_emac.dtsi b/arch/arm/boot/dts/sama5d3_emac.dtsi index b4544cf11bad..7cb235ef0fb6 100644 --- a/arch/arm/boot/dts/sama5d3_emac.dtsi +++ b/arch/arm/boot/dts/sama5d3_emac.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_emac.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_emac.dtsi - Device Tree Include file for SAMA5D3 SoC with * Ethernet. * * Copyright (C) 2013 Boris BREZILLON diff --git a/arch/arm/boot/dts/sama5d3_gmac.dtsi b/arch/arm/boot/dts/sama5d3_gmac.dtsi index de5ed59fb446..23f225fbb756 100644 --- a/arch/arm/boot/dts/sama5d3_gmac.dtsi +++ b/arch/arm/boot/dts/sama5d3_gmac.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_gmac.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_gmac.dtsi - Device Tree Include file for SAMA5D3 SoC with * Gigabit Ethernet. * * Copyright (C) 2013 Boris BREZILLON diff --git a/arch/arm/boot/dts/sama5d3_lcd.dtsi b/arch/arm/boot/dts/sama5d3_lcd.dtsi index 85d302701565..be7cfefc6c31 100644 --- a/arch/arm/boot/dts/sama5d3_lcd.dtsi +++ b/arch/arm/boot/dts/sama5d3_lcd.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_lcd.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_lcd.dtsi - Device Tree Include file for SAMA5D3 SoC with * LCD support * * Copyright (C) 2013 Boris BREZILLON @@ -13,40 +13,183 @@ / { ahb { apb { + hlcdc: hlcdc@f0030000 { + compatible = "atmel,sama5d3-hlcdc"; + reg = <0xf0030000 0x2000>; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; + clock-names = "periph_clk","sys_clk", "slow_clk"; + status = "disabled"; + + hlcdc-display-controller { + compatible = "atmel,hlcdc-display-controller"; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + }; + + hlcdc_pwm: hlcdc-pwm { + compatible = "atmel,hlcdc-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_pwm>; + #pwm-cells = <3>; + }; + }; + pinctrl@fffff200 { lcd { - pinctrl_lcd: lcd-0 { + pinctrl_lcd_base: lcd-base-0 { atmel,pins = - ; /* PE28 periph C LCDD23 pin */ + ; /* LCDPCK */ + }; + + pinctrl_lcd_pwm: lcd-pwm-0 { + atmel,pins = ; /* LCDPWM */ + }; + + pinctrl_lcd_rgb444: lcd-rgb-0 { + atmel,pins = + ; /* LCDD11 pin */ + }; + + pinctrl_lcd_rgb565: lcd-rgb-1 { + atmel,pins = + ; /* LCDD15 pin */ + }; + + pinctrl_lcd_rgb666: lcd-rgb-2 { + atmel,pins = + ; /* LCDD17 pin */ + }; + + pinctrl_lcd_rgb666_alt: lcd-rgb-2-alt { + atmel,pins = + ; /* LCDD17 pin */ + }; + + pinctrl_lcd_rgb888: lcd-rgb-3 { + atmel,pins = + ; /* LCDD23 pin */ + }; + + pinctrl_lcd_rgb888_alt: lcd-rgb-3-alt { + atmel,pins = + ; /* LCDD23 pin */ }; }; }; diff --git a/arch/arm/boot/dts/sama5d3_mci2.dtsi b/arch/arm/boot/dts/sama5d3_mci2.dtsi index 1b02208ea6ff..026b252f09b3 100644 --- a/arch/arm/boot/dts/sama5d3_mci2.dtsi +++ b/arch/arm/boot/dts/sama5d3_mci2.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_mci2.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_mci2.dtsi - Device Tree Include file for SAMA5D3 SoC with * 3 MMC ports * * Copyright (C) 2013 Boris BREZILLON diff --git a/arch/arm/boot/dts/sama5d3_tcb1.dtsi b/arch/arm/boot/dts/sama5d3_tcb1.dtsi index 02848453ca0c..f7fa58fe09f1 100644 --- a/arch/arm/boot/dts/sama5d3_tcb1.dtsi +++ b/arch/arm/boot/dts/sama5d3_tcb1.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_tcb1.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_tcb1.dtsi - Device Tree Include file for SAMA5D3 SoC with * 2 TC blocks. * * Copyright (C) 2013 Boris BREZILLON diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/sama5d3_uart.dtsi index 7a8d4c6115f7..2511d748867b 100644 --- a/arch/arm/boot/dts/sama5d3_uart.dtsi +++ b/arch/arm/boot/dts/sama5d3_uart.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_uart.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_uart.dtsi - Device Tree Include file for SAMA5D3 SoC with * UART support * * Copyright (C) 2013 Boris BREZILLON diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi index 4303874889c6..6b1bb58f9c0b 100644 --- a/arch/arm/boot/dts/sama5d4.dtsi +++ b/arch/arm/boot/dts/sama5d4.dtsi @@ -64,9 +64,13 @@ gpio2 = &pioC; gpio3 = &pioD; gpio4 = &pioE; + pwm0 = &pwm0; + ssc0 = &ssc0; + ssc1 = &ssc1; tcb0 = &tcb0; tcb1 = &tcb1; i2c0 = &i2c0; + i2c1 = &i2c1; i2c2 = &i2c2; }; cpus { @@ -310,6 +314,34 @@ #size-cells = <1>; ranges; + hlcdc: hlcdc@f0000000 { + compatible = "atmel,sama5d4-hlcdc"; + reg = <0xf0000000 0x4000>; + interrupts = <51 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; + clock-names = "periph_clk","sys_clk", "slow_clk"; + status = "disabled"; + + hlcdc-display-controller { + compatible = "atmel,hlcdc-display-controller"; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + }; + + hlcdc_pwm: hlcdc-pwm { + compatible = "atmel,hlcdc-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_pwm>; + #pwm-cells = <3>; + }; + }; + dma1: dma-controller@f0004000 { compatible = "atmel,sama5d4-dma"; reg = <0xf0004000 0x200>; @@ -319,6 +351,21 @@ clock-names = "dma_clk"; }; + isi: isi@f0008000 { + compatible = "atmel,at91sam9g45-isi"; + reg = <0xf0008000 0x4000>; + interrupts = <52 IRQ_TYPE_LEVEL_HIGH 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_isi_data_0_7>; + clocks = <&isi_clk>; + clock-names = "isi_clk"; + status = "disabled"; + port { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + ramc0: ramc@f0010000 { compatible = "atmel,sama5d3-ddramc"; reg = <0xf0010000 0x200>; @@ -800,6 +847,33 @@ clock-names = "mci_clk"; }; + ssc0: ssc@f8008000 { + compatible = "atmel,at91sam9g45-ssc"; + reg = <0xf8008000 0x4000>; + interrupts = <48 IRQ_TYPE_LEVEL_HIGH 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; + dmas = <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(26))>, + <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(27))>; + dma-names = "tx", "rx"; + clocks = <&ssc0_clk>; + clock-names = "pclk"; + status = "disabled"; + }; + + pwm0: pwm@f800c000 { + compatible = "atmel,sama5d3-pwm"; + reg = <0xf800c000 0x300>; + interrupts = <43 IRQ_TYPE_LEVEL_HIGH 4>; + #pwm-cells = <3>; + clocks = <&pwm_clk>; + status = "disabled"; + }; + spi0: spi@f8010000 { #address-cells = <1>; #size-cells = <0>; @@ -839,6 +913,25 @@ status = "disabled"; }; + i2c1: i2c@f8018000 { + compatible = "atmel,at91sam9x5-i2c"; + reg = <0xf8018000 0x4000>; + interrupts = <33 IRQ_TYPE_LEVEL_HIGH 6>; + dmas = <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(4)>, + <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(5)>; + dma-names = "tx", "rx"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&twi1_clk>; + status = "disabled"; + }; + tcb0: timer@f801c000 { compatible = "atmel,at91sam9x5-tcb"; reg = <0xf801c000 0x100>; @@ -853,6 +946,8 @@ interrupts = <54 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_macb0_rmii>; + #address-cells = <1>; + #size-cells = <0>; clocks = <&macb0_clk>, <&macb0_clk>; clock-names = "hclk", "pclk"; status = "disabled"; @@ -953,6 +1048,24 @@ status = "disabled"; }; + ssc1: ssc@fc014000 { + compatible = "atmel,at91sam9g45-ssc"; + reg = <0xfc014000 0x4000>; + interrupts = <49 IRQ_TYPE_LEVEL_HIGH 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; + dmas = <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(28))>, + <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(29))>; + dma-names = "tx", "rx"; + clocks = <&ssc1_clk>; + clock-names = "pclk"; + status = "disabled"; + }; + tcb1: timer@fc020000 { compatible = "atmel,at91sam9x5-tcb"; reg = <0xfc020000 0x100>; @@ -1008,6 +1121,46 @@ }; }; + aes@fc044000 { + compatible = "atmel,at91sam9g46-aes"; + reg = <0xfc044000 0x100>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>; + dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(41)>, + <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(40)>; + dma-names = "tx", "rx"; + clocks = <&aes_clk>; + clock-names = "aes_clk"; + status = "disabled"; + }; + + tdes@fc04c000 { + compatible = "atmel,at91sam9g46-tdes"; + reg = <0xfc04c000 0x100>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 0>; + dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(42)>, + <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(43)>; + dma-names = "tx", "rx"; + clocks = <&tdes_clk>; + clock-names = "tdes_clk"; + status = "disabled"; + }; + + sha@fc050000 { + compatible = "atmel,at91sam9g46-sha"; + reg = <0xfc050000 0x100>; + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 0>; + dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(44)>; + dma-names = "tx"; + clocks = <&sha_clk>; + clock-names = "sha_clk"; + status = "disabled"; + }; + rstc@fc068600 { compatible = "atmel,at91sam9g45-rstc"; reg = <0xfc068600 0x10>; @@ -1064,7 +1217,7 @@ }; dbgu: serial@fc069000 { - compatible = "atmel,at91sam9260-usart"; + compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart"; reg = <0xfc069000 0x200>; interrupts = <2 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; @@ -1190,6 +1343,14 @@ }; }; + i2c1 { + pinctrl_i2c1: i2c1-0 { + atmel,pins = + ; /* TWCK1, conflicts with UART0 TX and DIBN */ + }; + }; + i2c2 { pinctrl_i2c2: i2c2-0 { atmel,pins = @@ -1198,6 +1359,155 @@ }; }; + isi { + pinctrl_isi_data_0_7: isi-0-data-0-7 { + atmel,pins = + ; /* ISI_HSYNC */ + }; + pinctrl_isi_data_8_9: isi-0-data-8-9 { + atmel,pins = + ; /* ISI_D9, conflicts with SPI0_MOSI, PWML2 */ + }; + pinctrl_isi_data_10_11: isi-0-data-10-11 { + atmel,pins = + ; /* ISI_D11, conflicts with SPI0_NPCS0, PWML3 */ + }; + }; + + lcd { + pinctrl_lcd_base: lcd-base-0 { + atmel,pins = + ; /* LCDPCK */ + }; + pinctrl_lcd_pwm: lcd-pwm-0 { + atmel,pins = ; /* LCDPWM */ + }; + pinctrl_lcd_rgb444: lcd-rgb-0 { + atmel,pins = + ; /* LCDD11 pin */ + }; + pinctrl_lcd_rgb565: lcd-rgb-1 { + atmel,pins = + ; /* LCDD15 pin */ + }; + pinctrl_lcd_rgb666: lcd-rgb-2 { + atmel,pins = + ; /* LCDD23 pin */ + }; + pinctrl_lcd_rgb777: lcd-rgb-3 { + atmel,pins = + /* LCDDAT0 conflicts with TMS */ + ; /* LCDD23 pin */ + }; + pinctrl_lcd_rgb888: lcd-rgb-4 { + atmel,pins = + ; /* LCDD23 pin */ + }; + }; + macb0 { pinctrl_macb0_rmii: macb0_rmii-0 { atmel,pins = @@ -1281,6 +1591,38 @@ }; }; + ssc0 { + pinctrl_ssc0_tx: ssc0_tx { + atmel,pins = + ; /* TD0 */ + }; + + pinctrl_ssc0_rx: ssc0_rx { + atmel,pins = + ; /* RD0 */ + }; + }; + + ssc1 { + pinctrl_ssc1_tx: ssc1_tx { + atmel,pins = + ; /* TD1 */ + }; + + pinctrl_ssc1_rx: ssc1_rx { + atmel,pins = + ; /* RD1 */ + }; + }; + usart2 { pinctrl_usart2: usart2-0 { atmel,pins = diff --git a/arch/arm/boot/dts/sh7372-mackerel.dts b/arch/arm/boot/dts/sh7372-mackerel.dts deleted file mode 100644 index a759a276c9a9..000000000000 --- a/arch/arm/boot/dts/sh7372-mackerel.dts +++ /dev/null @@ -1,26 +0,0 @@ -/* - * Device Tree Source for the mackerel board - * - * Copyright (C) 2012 Renesas Solutions Corp. - * - * This file is licensed under the terms of the GNU General Public License - * version 2. This program is licensed "as is" without any warranty of any - * kind, whether express or implied. - */ - -/dts-v1/; -#include "sh7372.dtsi" - -/ { - model = "Mackerel (AP4 EVM 2nd)"; - compatible = "renesas,mackerel"; - - chosen { - bootargs = "console=tty0, console=ttySC0,115200 earlyprintk=sh-sci.0,115200 root=/dev/nfs nfsroot=,tcp,v3 ip=dhcp mem=240m rw"; - }; - - memory { - device_type = "memory"; - reg = <0x40000000 0x10000000>; - }; -}; diff --git a/arch/arm/boot/dts/sh7372.dtsi b/arch/arm/boot/dts/sh7372.dtsi deleted file mode 100644 index f863a10cb1b2..000000000000 --- a/arch/arm/boot/dts/sh7372.dtsi +++ /dev/null @@ -1,35 +0,0 @@ -/* - * Device Tree Source for the sh7372 SoC - * - * Copyright (C) 2012 Renesas Solutions Corp. - * - * This file is licensed under the terms of the GNU General Public License - * version 2. This program is licensed "as is" without any warranty of any - * kind, whether express or implied. - */ - -/include/ "skeleton.dtsi" - -/ { - compatible = "renesas,sh7372"; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - cpu@0 { - compatible = "arm,cortex-a8"; - device_type = "cpu"; - reg = <0x0>; - clock-frequency = <800000000>; - }; - }; - - pfc: pfc@e6050000 { - compatible = "renesas,pfc-sh7372"; - reg = <0xe6050000 0x8000>, - <0xe605801c 0x1c>; - gpio-controller; - #gpio-cells = <2>; - }; -}; diff --git a/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts b/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts deleted file mode 100644 index 6d32c87632d4..000000000000 --- a/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts +++ /dev/null @@ -1,366 +0,0 @@ -/* - * Device Tree Source for the KZM-A9-GT board - * - * Copyright (C) 2012 Horms Solutions Ltd. - * - * Based on sh73a0-kzm9g.dts - * Copyright (C) 2012 Renesas Solutions Corp. - * - * This file is licensed under the terms of the GNU General Public License - * version 2. This program is licensed "as is" without any warranty of any - * kind, whether express or implied. - */ - -/dts-v1/; -#include "sh73a0.dtsi" -#include -#include -#include - -/ { - model = "KZM-A9-GT"; - compatible = "renesas,kzm9g-reference", "renesas,sh73a0"; - - aliases { - serial4 = &scifa4; - }; - - cpus { - cpu@0 { - cpu0-supply = <&vdd_dvfs>; - operating-points = < - /* kHz uV */ - 1196000 1315000 - 598000 1175000 - 398667 1065000 - >; - voltage-tolerance = <1>; /* 1% */ - }; - }; - - chosen { - bootargs = "console=tty0 console=ttySC4,115200 root=/dev/nfs ip=dhcp ignore_loglevel rw"; - stdout-path = &scifa4; - }; - - memory { - device_type = "memory"; - reg = <0x41000000 0x1e800000>; - }; - - reg_1p8v: regulator@0 { - compatible = "regulator-fixed"; - regulator-name = "fixed-1.8V"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - reg_3p3v: regulator@1 { - compatible = "regulator-fixed"; - regulator-name = "fixed-3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - }; - - vmmc_sdhi0: regulator@2 { - compatible = "regulator-fixed"; - regulator-name = "SDHI0 Vcc"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&pfc 15 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - vmmc_sdhi2: regulator@3 { - compatible = "regulator-fixed"; - regulator-name = "SDHI2 Vcc"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&pfc 14 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - lan9220@10000000 { - compatible = "smsc,lan9220", "smsc,lan9115"; - reg = <0x10000000 0x100>; - phy-mode = "mii"; - interrupt-parent = <&irqpin0>; - interrupts = <3 IRQ_TYPE_EDGE_FALLING>; - reg-io-width = <4>; - smsc,irq-push-pull; - smsc,save-mac-address; - vddvario-supply = <®_1p8v>; - vdd33a-supply = <®_3p3v>; - }; - - leds { - compatible = "gpio-leds"; - led1 { - gpios = <&pfc 20 GPIO_ACTIVE_LOW>; - label = "LED1"; - }; - led2 { - gpios = <&pfc 21 GPIO_ACTIVE_LOW>; - label = "LED2"; - }; - led3 { - gpios = <&pfc 22 GPIO_ACTIVE_LOW>; - label = "LED3"; - }; - led4 { - gpios = <&pfc 23 GPIO_ACTIVE_LOW>; - label = "LED4"; - }; - }; - - keyboard { - compatible = "gpio-keys"; - - back-key { - gpios = <&pcf8575 8 GPIO_ACTIVE_LOW>; - linux,code = ; - label = "SW3"; - }; - - right-key { - gpios = <&pcf8575 9 GPIO_ACTIVE_LOW>; - linux,code = ; - label = "SW2-R"; - }; - - left-key { - gpios = <&pcf8575 10 GPIO_ACTIVE_LOW>; - linux,code = ; - label = "SW2-L"; - }; - - enter-key { - gpios = <&pcf8575 11 GPIO_ACTIVE_LOW>; - linux,code = ; - label = "SW2-P"; - }; - - up-key { - gpios = <&pcf8575 12 GPIO_ACTIVE_LOW>; - linux,code = ; - label = "SW2-U"; - }; - - down-key { - gpios = <&pcf8575 13 GPIO_ACTIVE_LOW>; - linux,code = ; - label = "SW2-D"; - }; - - home-key { - gpios = <&pcf8575 14 GPIO_ACTIVE_LOW>; - linux,code = ; - label = "SW1"; - }; - }; - - sound { - compatible = "simple-audio-card"; - simple-audio-card,format = "left_j"; - simple-audio-card,cpu { - sound-dai = <&sh_fsi2 0>; - }; - simple-audio-card,codec { - sound-dai = <&ak4648>; - bitclock-master; - frame-master; - system-clock-frequency = <11289600>; - }; - }; -}; - -&cmt1 { - status = "okay"; -}; - -&extal2_clk { - clock-frequency = <48000000>; -}; - -&i2c0 { - status = "okay"; - as3711@40 { - compatible = "ams,as3711"; - reg = <0x40>; - - regulators { - vdd_dvfs: sd1 { - regulator-name = "1.315V CPU"; - regulator-min-microvolt = <1050000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-boot-on; - }; - sd2 { - regulator-name = "1.8V"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - sd4 { - regulator-name = "1.215V"; - regulator-min-microvolt = <1215000>; - regulator-max-microvolt = <1235000>; - regulator-always-on; - regulator-boot-on; - }; - ldo2 { - regulator-name = "2.8V CPU"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - regulator-always-on; - regulator-boot-on; - }; - ldo3 { - regulator-name = "3.0V CPU"; - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3000000>; - regulator-always-on; - regulator-boot-on; - }; - ldo4 { - regulator-name = "2.8V"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - regulator-always-on; - regulator-boot-on; - }; - ldo5 { - regulator-name = "2.8V #2"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - regulator-always-on; - regulator-boot-on; - }; - ldo7 { - regulator-name = "1.15V CPU"; - regulator-min-microvolt = <1150000>; - regulator-max-microvolt = <1150000>; - regulator-always-on; - regulator-boot-on; - }; - ldo8 { - regulator-name = "1.15V CPU #2"; - regulator-min-microvolt = <1150000>; - regulator-max-microvolt = <1150000>; - regulator-always-on; - regulator-boot-on; - }; - }; - }; - - ak4648: ak4648@12 { - #sound-dai-cells = <0>; - compatible = "asahi-kasei,ak4648"; - reg = <0x12>; - }; -}; - -&i2c3 { - pinctrl-0 = <&i2c3_pins>; - pinctrl-names = "default"; - status = "okay"; - - pcf8575: gpio@20 { - compatible = "nxp,pcf8575"; - reg = <0x20>; - interrupt-parent = <&irqpin2>; - interrupts = <3 IRQ_TYPE_EDGE_FALLING>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - }; -}; - -&mmcif { - pinctrl-0 = <&mmcif_pins>; - pinctrl-names = "default"; - - bus-width = <8>; - vmmc-supply = <®_1p8v>; - status = "okay"; -}; - -&pfc { - i2c3_pins: i2c3 { - renesas,groups = "i2c3_1"; - renesas,function = "i2c3"; - }; - - mmcif_pins: mmc { - mux { - renesas,groups = "mmc0_data8_0", "mmc0_ctrl_0"; - renesas,function = "mmc0"; - }; - cfg { - renesas,groups = "mmc0_data8_0"; - renesas,pins = "PORT279"; - bias-pull-up; - }; - }; - - scifa4_pins: serial4 { - renesas,groups = "scifa4_data", "scifa4_ctrl"; - renesas,function = "scifa4"; - }; - - sdhi0_pins: sd0 { - renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_cd", "sdhi0_wp"; - renesas,function = "sdhi0"; - }; - - sdhi2_pins: sd2 { - renesas,groups = "sdhi2_data4", "sdhi2_ctrl"; - renesas,function = "sdhi2"; - }; - - fsia_pins: sounda { - renesas,groups = "fsia_mclk_in", "fsia_sclk_in", - "fsia_data_in", "fsia_data_out"; - renesas,function = "fsia"; - }; -}; - -&scifa4 { - pinctrl-0 = <&scifa4_pins>; - pinctrl-names = "default"; - - status = "okay"; -}; - -&sdhi0 { - pinctrl-0 = <&sdhi0_pins>; - pinctrl-names = "default"; - - vmmc-supply = <&vmmc_sdhi0>; - bus-width = <4>; - status = "okay"; -}; - -&sdhi2 { - pinctrl-0 = <&sdhi2_pins>; - pinctrl-names = "default"; - - vmmc-supply = <&vmmc_sdhi2>; - bus-width = <4>; - broken-cd; - status = "okay"; -}; - -&sh_fsi2 { - pinctrl-0 = <&fsia_pins>; - pinctrl-names = "default"; - - status = "okay"; -}; diff --git a/arch/arm/boot/dts/sh73a0-kzm9g.dts b/arch/arm/boot/dts/sh73a0-kzm9g.dts index 27c5f426d172..022ba505f573 100644 --- a/arch/arm/boot/dts/sh73a0-kzm9g.dts +++ b/arch/arm/boot/dts/sh73a0-kzm9g.dts @@ -1,6 +1,9 @@ /* * Device Tree Source for the KZM-A9-GT board * + * Copyright (C) 2012 Horms Solutions Ltd. + * + * Based on sh73a0-kzm9g.dts * Copyright (C) 2012 Renesas Solutions Corp. * * This file is licensed under the terms of the GNU General Public License @@ -10,17 +13,388 @@ /dts-v1/; #include "sh73a0.dtsi" +#include +#include +#include / { model = "KZM-A9-GT"; compatible = "renesas,kzm9g", "renesas,sh73a0"; + aliases { + serial4 = &scifa4; + }; + + cpus { + cpu@0 { + cpu0-supply = <&vdd_dvfs>; + operating-points = < + /* kHz uV */ + 1196000 1315000 + 598000 1175000 + 398667 1065000 + >; + voltage-tolerance = <1>; /* 1% */ + }; + }; + chosen { - bootargs = "console=tty0 console=ttySC4,115200 root=/dev/nfs ip=dhcp ignore_loglevel earlyprintk=sh-sci.4,115200 rw"; + bootargs = "console=tty0 console=ttySC4,115200 root=/dev/nfs ip=dhcp ignore_loglevel rw"; + stdout-path = &scifa4; }; memory { device_type = "memory"; - reg = <0x41000000 0x1e800000>; + reg = <0x40000000 0x20000000>; + }; + + reg_1p8v: regulator@0 { + compatible = "regulator-fixed"; + regulator-name = "fixed-1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + reg_3p3v: regulator@1 { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + vmmc_sdhi0: regulator@2 { + compatible = "regulator-fixed"; + regulator-name = "SDHI0 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pfc 15 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vmmc_sdhi2: regulator@3 { + compatible = "regulator-fixed"; + regulator-name = "SDHI2 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pfc 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + leds { + compatible = "gpio-leds"; + led1 { + gpios = <&pfc 20 GPIO_ACTIVE_LOW>; + label = "LED1"; + }; + led2 { + gpios = <&pfc 21 GPIO_ACTIVE_LOW>; + label = "LED2"; + }; + led3 { + gpios = <&pfc 22 GPIO_ACTIVE_LOW>; + label = "LED3"; + }; + led4 { + gpios = <&pfc 23 GPIO_ACTIVE_LOW>; + label = "LED4"; + }; + }; + + keyboard { + compatible = "gpio-keys"; + + back-key { + gpios = <&pcf8575 8 GPIO_ACTIVE_LOW>; + linux,code = ; + label = "SW3"; + }; + + right-key { + gpios = <&pcf8575 9 GPIO_ACTIVE_LOW>; + linux,code = ; + label = "SW2-R"; + }; + + left-key { + gpios = <&pcf8575 10 GPIO_ACTIVE_LOW>; + linux,code = ; + label = "SW2-L"; + }; + + enter-key { + gpios = <&pcf8575 11 GPIO_ACTIVE_LOW>; + linux,code = ; + label = "SW2-P"; + }; + + up-key { + gpios = <&pcf8575 12 GPIO_ACTIVE_LOW>; + linux,code = ; + label = "SW2-U"; + }; + + down-key { + gpios = <&pcf8575 13 GPIO_ACTIVE_LOW>; + linux,code = ; + label = "SW2-D"; + }; + + home-key { + gpios = <&pcf8575 14 GPIO_ACTIVE_LOW>; + linux,code = ; + label = "SW1"; + }; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,format = "left_j"; + simple-audio-card,cpu { + sound-dai = <&sh_fsi2 0>; + }; + simple-audio-card,codec { + sound-dai = <&ak4648>; + bitclock-master; + frame-master; + system-clock-frequency = <11289600>; + }; }; }; + +&bsc { + ethernet@10000000 { + compatible = "smsc,lan9220", "smsc,lan9115"; + reg = <0x10000000 0x100>; + phy-mode = "mii"; + interrupt-parent = <&irqpin0>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + reg-io-width = <4>; + smsc,irq-push-pull; + smsc,save-mac-address; + vddvario-supply = <®_1p8v>; + vdd33a-supply = <®_3p3v>; + }; +}; + +&cmt1 { + status = "okay"; +}; + +&extal2_clk { + clock-frequency = <48000000>; +}; + +&i2c0 { + status = "okay"; + + compass@c { + compatible = "asahi-kasei,ak8975"; + reg = <0x0c>; + interrupt-parent = <&irqpin3>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + }; + + ak4648: codec@12 { + compatible = "asahi-kasei,ak4648"; + reg = <0x12>; + #sound-dai-cells = <0>; + }; + + accelerometer@1d { + compatible = "adi,adxl34x"; + reg = <0x1d>; + interrupt-parent = <&irqpin3>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>, + <3 IRQ_TYPE_LEVEL_HIGH>; + }; + + rtc@32 { + compatible = "ricoh,r2025sd"; + reg = <0x32>; + }; + + as3711@40 { + compatible = "ams,as3711"; + reg = <0x40>; + + regulators { + vdd_dvfs: sd1 { + regulator-name = "1.315V CPU"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + sd2 { + regulator-name = "1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + sd4 { + regulator-name = "1.215V"; + regulator-min-microvolt = <1215000>; + regulator-max-microvolt = <1235000>; + regulator-always-on; + regulator-boot-on; + }; + ldo2 { + regulator-name = "2.8V CPU"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-boot-on; + }; + ldo3 { + regulator-name = "3.0V CPU"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + regulator-boot-on; + }; + ldo4 { + regulator-name = "2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-boot-on; + }; + ldo5 { + regulator-name = "2.8V #2"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-boot-on; + }; + ldo7 { + regulator-name = "1.15V CPU"; + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1150000>; + regulator-always-on; + regulator-boot-on; + }; + ldo8 { + regulator-name = "1.15V CPU #2"; + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1150000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; +}; + +&i2c1 { + status = "okay"; + + touchscreen@55 { + compatible = "sitronix,st1232"; + reg = <0x55>; + interrupt-parent = <&irqpin1>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + }; +}; + +&i2c3 { + pinctrl-0 = <&i2c3_pins>; + pinctrl-names = "default"; + status = "okay"; + + pcf8575: gpio@20 { + compatible = "nxp,pcf8575"; + reg = <0x20>; + interrupt-parent = <&irqpin2>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; +}; + +&mmcif { + pinctrl-0 = <&mmcif_pins>; + pinctrl-names = "default"; + + bus-width = <8>; + vmmc-supply = <®_1p8v>; + status = "okay"; +}; + +&pfc { + i2c3_pins: i2c3 { + renesas,groups = "i2c3_1"; + renesas,function = "i2c3"; + }; + + mmcif_pins: mmc { + mux { + renesas,groups = "mmc0_data8_0", "mmc0_ctrl_0"; + renesas,function = "mmc0"; + }; + cfg { + renesas,groups = "mmc0_data8_0"; + renesas,pins = "PORT279"; + bias-pull-up; + }; + }; + + scifa4_pins: serial4 { + renesas,groups = "scifa4_data", "scifa4_ctrl"; + renesas,function = "scifa4"; + }; + + sdhi0_pins: sd0 { + renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_cd", "sdhi0_wp"; + renesas,function = "sdhi0"; + }; + + sdhi2_pins: sd2 { + renesas,groups = "sdhi2_data4", "sdhi2_ctrl"; + renesas,function = "sdhi2"; + }; + + fsia_pins: sounda { + renesas,groups = "fsia_mclk_in", "fsia_sclk_in", + "fsia_data_in", "fsia_data_out"; + renesas,function = "fsia"; + }; +}; + +&scifa4 { + pinctrl-0 = <&scifa4_pins>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&sdhi0 { + pinctrl-0 = <&sdhi0_pins>; + pinctrl-names = "default"; + + vmmc-supply = <&vmmc_sdhi0>; + bus-width = <4>; + status = "okay"; +}; + +&sdhi2 { + pinctrl-0 = <&sdhi2_pins>; + pinctrl-names = "default"; + + vmmc-supply = <&vmmc_sdhi2>; + bus-width = <4>; + broken-cd; + status = "okay"; +}; + +&sh_fsi2 { + pinctrl-0 = <&fsia_pins>; + pinctrl-names = "default"; + + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sh73a0.dtsi b/arch/arm/boot/dts/sh73a0.dtsi index 2dfd5b44255d..45b539ce4d35 100644 --- a/arch/arm/boot/dts/sh73a0.dtsi +++ b/arch/arm/boot/dts/sh73a0.dtsi @@ -11,6 +11,7 @@ /include/ "skeleton.dtsi" #include +#include #include / { @@ -26,15 +27,24 @@ compatible = "arm,cortex-a9"; reg = <0>; clock-frequency = <1196000000>; + power-domains = <&pd_a2sl>; }; cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <1>; clock-frequency = <1196000000>; + power-domains = <&pd_a2sl>; }; }; + timer@f0000600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0xf0000600 0x20>; + interrupts = ; + clocks = <&twd_clk>; + }; + gic: interrupt-controller@f0001000 { compatible = "arm,cortex-a9-gic"; #interrupt-cells = <3>; @@ -49,6 +59,7 @@ interrupts = <0 37 IRQ_TYPE_LEVEL_HIGH>, <0 38 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "sec", "temp"; + power-domains = <&pd_a4bc1>; }; sbsc1: memory-controller@fe400000 { @@ -57,6 +68,7 @@ interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>, <0 36 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "sec", "temp"; + power-domains = <&pd_a4bc0>; }; pmu { @@ -69,11 +81,12 @@ compatible = "renesas,cmt-48-sh73a0", "renesas,cmt-48"; reg = <0xe6138000 0x200>; interrupts = <0 65 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks SH73A0_CLK_CMT1>; + clock-names = "fck"; + power-domains = <&pd_c5>; renesas,channels-mask = <0x3f>; - clocks = <&mstp3_clks SH73A0_CLK_CMT1>; - clock-names = "fck"; status = "disabled"; }; @@ -94,6 +107,9 @@ 0 6 IRQ_TYPE_LEVEL_HIGH 0 7 IRQ_TYPE_LEVEL_HIGH 0 8 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks SH73A0_CLK_INTCA0>; + power-domains = <&pd_a4s>; + control-parent; }; irqpin1: irqpin@e6900004 { @@ -113,6 +129,8 @@ 0 14 IRQ_TYPE_LEVEL_HIGH 0 15 IRQ_TYPE_LEVEL_HIGH 0 16 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks SH73A0_CLK_INTCA0>; + power-domains = <&pd_a4s>; control-parent; }; @@ -133,6 +151,9 @@ 0 22 IRQ_TYPE_LEVEL_HIGH 0 23 IRQ_TYPE_LEVEL_HIGH 0 24 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks SH73A0_CLK_INTCA0>; + power-domains = <&pd_a4s>; + control-parent; }; irqpin3: irqpin@e690000c { @@ -152,6 +173,9 @@ 0 30 IRQ_TYPE_LEVEL_HIGH 0 31 IRQ_TYPE_LEVEL_HIGH 0 32 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks SH73A0_CLK_INTCA0>; + power-domains = <&pd_a4s>; + control-parent; }; i2c0: i2c@e6820000 { @@ -164,6 +188,7 @@ 0 169 IRQ_TYPE_LEVEL_HIGH 0 170 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp1_clks SH73A0_CLK_IIC0>; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -177,6 +202,7 @@ 0 53 IRQ_TYPE_LEVEL_HIGH 0 54 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks SH73A0_CLK_IIC1>; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -190,6 +216,7 @@ 0 173 IRQ_TYPE_LEVEL_HIGH 0 174 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp0_clks SH73A0_CLK_IIC2>; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -203,6 +230,7 @@ 0 185 IRQ_TYPE_LEVEL_HIGH 0 186 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp4_clks SH73A0_CLK_IIC3>; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -216,6 +244,7 @@ 0 189 IRQ_TYPE_LEVEL_HIGH 0 190 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp4_clks SH73A0_CLK_IIC4>; + power-domains = <&pd_c5>; status = "disabled"; }; @@ -225,6 +254,7 @@ interrupts = <0 140 IRQ_TYPE_LEVEL_HIGH 0 141 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks SH73A0_CLK_MMCIF0>; + power-domains = <&pd_a3sp>; reg-io-width = <4>; status = "disabled"; }; @@ -236,6 +266,7 @@ 0 84 IRQ_TYPE_LEVEL_HIGH 0 85 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks SH73A0_CLK_SDHI0>; + power-domains = <&pd_a3sp>; cap-sd-highspeed; status = "disabled"; }; @@ -247,6 +278,7 @@ interrupts = <0 88 IRQ_TYPE_LEVEL_HIGH 0 89 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks SH73A0_CLK_SDHI1>; + power-domains = <&pd_a3sp>; toshiba,mmc-wrprotect-disable; cap-sd-highspeed; status = "disabled"; @@ -258,6 +290,7 @@ interrupts = <0 104 IRQ_TYPE_LEVEL_HIGH 0 105 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks SH73A0_CLK_SDHI2>; + power-domains = <&pd_a3sp>; toshiba,mmc-wrprotect-disable; cap-sd-highspeed; status = "disabled"; @@ -269,6 +302,7 @@ interrupts = <0 72 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks SH73A0_CLK_SCIFA0>; clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -278,6 +312,7 @@ interrupts = <0 73 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks SH73A0_CLK_SCIFA1>; clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -287,6 +322,7 @@ interrupts = <0 74 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks SH73A0_CLK_SCIFA2>; clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -296,6 +332,7 @@ interrupts = <0 75 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks SH73A0_CLK_SCIFA3>; clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -305,6 +342,7 @@ interrupts = <0 78 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks SH73A0_CLK_SCIFA4>; clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -314,6 +352,7 @@ interrupts = <0 79 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks SH73A0_CLK_SCIFA5>; clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -323,6 +362,7 @@ interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks SH73A0_CLK_SCIFA6>; clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -332,6 +372,7 @@ interrupts = <0 143 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks SH73A0_CLK_SCIFA7>; clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -341,6 +382,7 @@ interrupts = <0 80 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks SH73A0_CLK_SCIFB>; clock-names = "sci_ick"; + power-domains = <&pd_a3sp>; status = "disabled"; }; @@ -359,6 +401,117 @@ <&irqpin2 4 0>, <&irqpin2 5 0>, <&irqpin2 6 0>, <&irqpin2 7 0>, <&irqpin3 0 0>, <&irqpin3 1 0>, <&irqpin3 2 0>, <&irqpin3 3 0>, <&irqpin3 4 0>, <&irqpin3 5 0>, <&irqpin3 6 0>, <&irqpin3 7 0>; + power-domains = <&pd_c5>; + }; + + sysc: system-controller@e6180000 { + compatible = "renesas,sysc-sh73a0", "renesas,sysc-rmobile"; + reg = <0xe6180000 0x8000>, <0xe6188000 0x8000>; + + pm-domains { + pd_c5: c5 { + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_c4: c4@0 { + reg = <0>; + #power-domain-cells = <0>; + }; + + pd_d4: d4@1 { + reg = <1>; + #power-domain-cells = <0>; + }; + + pd_a4bc0: a4bc0@4 { + reg = <4>; + #power-domain-cells = <0>; + }; + + pd_a4bc1: a4bc1@5 { + reg = <5>; + #power-domain-cells = <0>; + }; + + pd_a4lc0: a4lc0@6 { + reg = <6>; + #power-domain-cells = <0>; + }; + + pd_a4lc1: a4lc1@7 { + reg = <7>; + #power-domain-cells = <0>; + }; + + pd_a4mp: a4mp@8 { + reg = <8>; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_a3mp: a3mp@9 { + reg = <9>; + #power-domain-cells = <0>; + }; + + pd_a3vc: a3vc@10 { + reg = <10>; + #power-domain-cells = <0>; + }; + }; + + pd_a4rm: a4rm@12 { + reg = <12>; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_a3r: a3r@13 { + reg = <13>; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_a2rv: a2rv@14 { + reg = <14>; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + }; + }; + }; + + pd_a4s: a4s@16 { + reg = <16>; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_a3sp: a3sp@17 { + reg = <17>; + #power-domain-cells = <0>; + }; + + pd_a3sg: a3sg@18 { + reg = <18>; + #power-domain-cells = <0>; + }; + + pd_a3sm: a3sm@19 { + reg = <19>; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <0>; + + pd_a2sl: a2sl@20 { + reg = <20>; + #power-domain-cells = <0>; + }; + }; + }; + }; + }; }; sh_fsi2: sound@ec230000 { @@ -366,9 +519,22 @@ compatible = "renesas,fsi2-sh73a0", "renesas,sh_fsi2"; reg = <0xec230000 0x400>; interrupts = <0 146 0x4>; + power-domains = <&pd_a4mp>; status = "disabled"; }; + bsc: bus@fec10000 { + compatible = "renesas,bsc-sh73a0", "renesas,bsc", + "simple-pm-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x20000000>; + reg = <0xfec10000 0x400>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&zb_clk>; + power-domains = <&pd_a4s>; + }; + clocks { #address-cells = <1>; #size-cells = <1>; @@ -426,133 +592,159 @@ vclk1_clk: vclk1_clk@e6150008 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150008 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&extcki_clk>, <&extal2_clk>, <&main_div2_clk>, + <&extalr_clk>, <&cpg_clocks SH73A0_CLK_MAIN>, + <0>; #clock-cells = <0>; clock-output-names = "vclk1"; }; vclk2_clk: vclk2_clk@e615000c { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe615000c 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&extcki_clk>, <&extal2_clk>, <&main_div2_clk>, + <&extalr_clk>, <&cpg_clocks SH73A0_CLK_MAIN>, + <0>; #clock-cells = <0>; clock-output-names = "vclk2"; }; vclk3_clk: vclk3_clk@e615001c { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe615001c 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&extcki_clk>, <&extal2_clk>, <&main_div2_clk>, + <&extalr_clk>, <&cpg_clocks SH73A0_CLK_MAIN>, + <0>; #clock-cells = <0>; clock-output-names = "vclk3"; }; zb_clk: zb_clk@e6150010 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150010 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <0>, + <&cpg_clocks SH73A0_CLK_PLL2>, <0>; #clock-cells = <0>; clock-output-names = "zb"; }; flctl_clk: flctl_clk@e6150014 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150014 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <0>, + <&cpg_clocks SH73A0_CLK_PLL2>, <0>; #clock-cells = <0>; clock-output-names = "flctlck"; }; sdhi0_clk: sdhi0_clk@e6150074 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150074 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&pll1_div13_clk>, <0>; #clock-cells = <0>; clock-output-names = "sdhi0ck"; }; sdhi1_clk: sdhi1_clk@e6150078 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150078 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&pll1_div13_clk>, <0>; #clock-cells = <0>; clock-output-names = "sdhi1ck"; }; sdhi2_clk: sdhi2_clk@e615007c { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe615007c 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&pll1_div13_clk>, <0>; #clock-cells = <0>; clock-output-names = "sdhi2ck"; }; fsia_clk: fsia_clk@e6150018 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150018 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&fsiack_clk>, <&fsiack_clk>; #clock-cells = <0>; clock-output-names = "fsia"; }; fsib_clk: fsib_clk@e6150090 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150090 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&fsibck_clk>, <&fsibck_clk>; #clock-cells = <0>; clock-output-names = "fsib"; }; sub_clk: sub_clk@e6150080 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150080 4>; - clocks = <&extal2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&extal2_clk>, <&extal2_clk>; #clock-cells = <0>; clock-output-names = "sub"; }; spua_clk: spua_clk@e6150084 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150084 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&extal2_clk>, <&extal2_clk>; #clock-cells = <0>; clock-output-names = "spua"; }; spuv_clk: spuv_clk@e6150094 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150094 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&extal2_clk>, <&extal2_clk>; #clock-cells = <0>; clock-output-names = "spuv"; }; msu_clk: msu_clk@e6150088 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150088 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <0>, + <&cpg_clocks SH73A0_CLK_PLL2>, <0>; #clock-cells = <0>; clock-output-names = "msu"; }; hsi_clk: hsi_clk@e615008c { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe615008c 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&pll1_div7_clk>, <0>; #clock-cells = <0>; clock-output-names = "hsi"; }; mfg1_clk: mfg1_clk@e6150098 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150098 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <0>, + <&cpg_clocks SH73A0_CLK_PLL2>, <0>; #clock-cells = <0>; clock-output-names = "mfg1"; }; mfg2_clk: mfg2_clk@e615009c { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe615009c 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <0>, + <&cpg_clocks SH73A0_CLK_PLL2>, <0>; #clock-cells = <0>; clock-output-names = "mfg2"; }; dsit_clk: dsit_clk@e6150060 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150060 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <0>, + <&cpg_clocks SH73A0_CLK_PLL2>, <0>; #clock-cells = <0>; clock-output-names = "dsit"; }; dsi0p_clk: dsi0p_clk@e6150064 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150064 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&cpg_clocks SH73A0_CLK_MAIN>, <&extal2_clk>, + <&extcki_clk>, <0>, <0>, <0>; #clock-cells = <0>; clock-output-names = "dsi0pck"; }; @@ -695,5 +887,16 @@ clock-output-names = "iic3", "iic4", "keysc"; }; + mstp5_clks: mstp5_clks@e6150144 { + compatible = "renesas,sh73a0-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0xe6150144 4>, <0xe615003c 4>; + clocks = <&cpg_clocks SH73A0_CLK_HP>; + #clock-cells = <1>; + clock-indices = < + SH73A0_CLK_INTCA0 + >; + clock-output-names = + "intca0"; + }; }; }; diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi index bfd3f1c734b8..2201cd5da3bb 100644 --- a/arch/arm/boot/dts/ste-dbx5x0.dtsi +++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi @@ -1017,23 +1017,6 @@ status = "disabled"; }; - vmmci: regulator-gpio { - compatible = "regulator-gpio"; - - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2900000>; - regulator-name = "mmci-reg"; - regulator-type = "voltage"; - - startup-delay-us = <100>; - enable-active-high; - - states = <1800000 0x1 - 2900000 0x0>; - - status = "disabled"; - }; - mcde@a0350000 { compatible = "stericsson,mcde"; reg = <0xa0350000 0x1000>, /* MCDE */ diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi index bf8f0eddc2c0..744c1e3a744d 100644 --- a/arch/arm/boot/dts/ste-href.dtsi +++ b/arch/arm/boot/dts/ste-href.dtsi @@ -111,6 +111,21 @@ pinctrl-1 = <&i2c3_sleep_mode>; }; + vmmci: regulator-gpio { + compatible = "regulator-gpio"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-name = "mmci-reg"; + regulator-type = "voltage"; + + startup-delay-us = <100>; + enable-active-high; + + states = <1800000 0x1 + 2900000 0x0>; + }; + // External Micro SD slot sdi0_per1@80126000 { arm,primecell-periphid = <0x10480180>; diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts index 206826a855c0..1bc84ebdccaa 100644 --- a/arch/arm/boot/dts/ste-snowball.dts +++ b/arch/arm/boot/dts/ste-snowball.dts @@ -146,8 +146,21 @@ }; vmmci: regulator-gpio { + compatible = "regulator-gpio"; + gpios = <&gpio7 4 0x4>; enable-gpio = <&gpio6 25 0x4>; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-name = "mmci-reg"; + regulator-type = "voltage"; + + startup-delay-us = <100>; + enable-active-high; + + states = <1800000 0x1 + 2900000 0x0>; }; // External Micro SD slot diff --git a/arch/arm/boot/dts/tegra124-jetson-tk1-emc.dtsi b/arch/arm/boot/dts/tegra124-jetson-tk1-emc.dtsi new file mode 100644 index 000000000000..2c5cede686dc --- /dev/null +++ b/arch/arm/boot/dts/tegra124-jetson-tk1-emc.dtsi @@ -0,0 +1,2421 @@ +/ { + clock@0,60006000 { + emc-timings-3 { + nvidia,ram-code = <3>; + + timing-12750000 { + clock-frequency = <12750000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-20400000 { + clock-frequency = <20400000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-40800000 { + clock-frequency = <40800000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-68000000 { + clock-frequency = <68000000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-102000000 { + clock-frequency = <102000000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-204000000 { + clock-frequency = <204000000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-300000000 { + clock-frequency = <300000000>; + nvidia,parent-clock-frequency = <600000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_C>; + clock-names = "emc-parent"; + }; + timing-396000000 { + clock-frequency = <396000000>; + nvidia,parent-clock-frequency = <792000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_M>; + clock-names = "emc-parent"; + }; + timing-528000000 { + clock-frequency = <528000000>; + nvidia,parent-clock-frequency = <528000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>; + clock-names = "emc-parent"; + }; + timing-600000000 { + clock-frequency = <600000000>; + nvidia,parent-clock-frequency = <600000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>; + clock-names = "emc-parent"; + }; + timing-792000000 { + clock-frequency = <792000000>; + nvidia,parent-clock-frequency = <792000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>; + clock-names = "emc-parent"; + }; + timing-924000000 { + clock-frequency = <924000000>; + nvidia,parent-clock-frequency = <924000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>; + clock-names = "emc-parent"; + }; + }; + }; + + emc@0,7001b000 { + emc-timings-3 { + nvidia,ram-code = <3>; + + timing-12750000 { + clock-frequency = <12750000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000e000e>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000a + 0x00000005 + 0x0000000b + 0x00000000 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x00000060 + 0x00000000 + 0x00000018 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000007 + 0x0000000f + 0x00000005 + 0x00000005 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000000 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000064 + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000e0e + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000007 + 0x00000000 + 0x00000042 + 0x000e000e + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x800001c5 + 0x0000000a + >; + }; + + timing-20400000 { + clock-frequency = <20400000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000e000e>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000000 + 0x00000005 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000a + 0x00000005 + 0x0000000b + 0x00000000 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x0000009a + 0x00000000 + 0x00000026 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000007 + 0x0000000f + 0x00000006 + 0x00000006 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000000 + 0x00000000 + 0x00000005 + 0x00000005 + 0x000000a0 + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000e0e + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x0000000b + 0x00000000 + 0x00000042 + 0x000e000e + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x8000023a + 0x0000000a + >; + }; + + timing-40800000 { + clock-frequency = <40800000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000e000e>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000001 + 0x0000000a + 0x00000000 + 0x00000001 + 0x00000000 + 0x00000004 + 0x0000000a + 0x00000005 + 0x0000000b + 0x00000000 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x00000134 + 0x00000000 + 0x0000004d + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000008 + 0x0000000f + 0x0000000c + 0x0000000c + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000000 + 0x00000000 + 0x00000005 + 0x00000005 + 0x0000013f + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000e0e + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000015 + 0x00000000 + 0x00000042 + 0x000e000e + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x80000370 + 0x0000000a + >; + }; + + timing-68000000 { + clock-frequency = <68000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000e000e>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000003 + 0x00000011 + 0x00000000 + 0x00000002 + 0x00000000 + 0x00000004 + 0x0000000a + 0x00000005 + 0x0000000b + 0x00000000 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x00000202 + 0x00000000 + 0x00000080 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x0000000f + 0x0000000f + 0x00000013 + 0x00000013 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000001 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000213 + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000e0e + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000022 + 0x00000000 + 0x00000042 + 0x000e000e + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x8000050e + 0x0000000a + >; + }; + + timing-102000000 { + clock-frequency = <102000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000e000e>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000004 + 0x0000001a + 0x00000000 + 0x00000003 + 0x00000001 + 0x00000004 + 0x0000000a + 0x00000005 + 0x0000000b + 0x00000001 + 0x00000001 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x00000304 + 0x00000000 + 0x000000c1 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000018 + 0x0000000f + 0x0000001c + 0x0000001c + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x0000031c + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000e0e + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000033 + 0x00000000 + 0x00000042 + 0x000e000e + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x80000713 + 0x0000000a + >; + }; + + timing-204000000 { + clock-frequency = <204000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008cd>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000e000e>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x00000009 + 0x00000035 + 0x00000000 + 0x00000006 + 0x00000002 + 0x00000005 + 0x0000000a + 0x00000005 + 0x0000000b + 0x00000002 + 0x00000002 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000004 + 0x00000006 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000003 + 0x0000000d + 0x0000000f + 0x00000011 + 0x00000607 + 0x00000000 + 0x00000181 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000032 + 0x0000000f + 0x00000038 + 0x00000038 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000006 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000638 + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00080000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00008000 + 0x00000000 + 0x00000000 + 0x00008000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00090000 + 0x00090000 + 0x00090000 + 0x00090000 + 0x00009000 + 0x00009000 + 0x00009000 + 0x00009000 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000707 + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000066 + 0x00000000 + 0x00000100 + 0x000e000e + 0x00000000 + 0x00000003 + 0x0000d2b3 + 0x80000d22 + 0x0000000a + >; + }; + + timing-300000000 { + clock-frequency = <300000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73340000>; + nvidia,emc-cfg-2 = <0x000008d5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200000>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000321>; + nvidia,emc-mrs-wait-cnt = <0x0173000e>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x01231339>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x0000000d + 0x0000004d + 0x00000000 + 0x00000009 + 0x00000003 + 0x00000004 + 0x00000008 + 0x00000002 + 0x00000009 + 0x00000003 + 0x00000003 + 0x00000002 + 0x00000002 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000005 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000007 + 0x00020000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000001 + 0x0000000e + 0x00000010 + 0x00000012 + 0x000008e4 + 0x00000000 + 0x00000239 + 0x00000001 + 0x00000008 + 0x00000001 + 0x00000000 + 0x0000004b + 0x0000000e + 0x00000052 + 0x00000200 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000008 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000924 + 0x00000000 + 0x00000000 + 0x00000000 + 0x104ab098 + 0x002c00a0 + 0x00008000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00098000 + 0x00098000 + 0x00000000 + 0x00098000 + 0x00098000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00050000 + 0x00050000 + 0x00050000 + 0x00050000 + 0x00005000 + 0x00005000 + 0x00005000 + 0x00005000 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000505 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x51451420 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000096 + 0x00000000 + 0x00000100 + 0x0173000e + 0x00000000 + 0x00000003 + 0x000052a3 + 0x800012d7 + 0x00000009 + >; + }; + + timing-396000000 { + clock-frequency = <396000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73340000>; + nvidia,emc-cfg-2 = <0x00000895>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200000>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000521>; + nvidia,emc-mrs-wait-cnt = <0x015b000e>; + nvidia,emc-sel-dpd-ctrl = <0x00040008>; + nvidia,emc-xm2dqspadctrl2 = <0x01231339>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x00000011 + 0x00000066 + 0x00000000 + 0x0000000c + 0x00000004 + 0x00000004 + 0x00000008 + 0x00000002 + 0x0000000a + 0x00000004 + 0x00000004 + 0x00000002 + 0x00000002 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000005 + 0x00000002 + 0x00000000 + 0x00000001 + 0x00000008 + 0x00020000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x0000000f + 0x00000010 + 0x00000012 + 0x00000bd1 + 0x00000000 + 0x000002f4 + 0x00000001 + 0x00000008 + 0x00000001 + 0x00000000 + 0x00000063 + 0x0000000f + 0x0000006c + 0x00000200 + 0x00000004 + 0x00000005 + 0x00000004 + 0x0000000b + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000c11 + 0x00000000 + 0x00000000 + 0x00000000 + 0x104ab098 + 0x002c00a0 + 0x00008000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00070000 + 0x00070000 + 0x00000000 + 0x00070000 + 0x00070000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00038000 + 0x00038000 + 0x00038000 + 0x00038000 + 0x00003800 + 0x00003800 + 0x00003800 + 0x00003800 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000505 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x51451420 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x000000c6 + 0x00000000 + 0x00000100 + 0x015b000e + 0x00000000 + 0x00000003 + 0x000052a3 + 0x8000188b + 0x00000009 + >; + }; + + timing-528000000 { + clock-frequency = <528000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73300000>; + nvidia,emc-cfg-2 = <0x0000089d>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000941>; + nvidia,emc-mrs-wait-cnt = <0x0139000e>; + nvidia,emc-sel-dpd-ctrl = <0x00040008>; + nvidia,emc-xm2dqspadctrl2 = <0x0123133d>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x00000018 + 0x00000088 + 0x00000000 + 0x00000010 + 0x00000006 + 0x00000006 + 0x00000009 + 0x00000002 + 0x0000000d + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000002 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000001 + 0x00000009 + 0x00030000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000010 + 0x00000012 + 0x00000014 + 0x00000fd6 + 0x00000000 + 0x000003f5 + 0x00000002 + 0x0000000b + 0x00000001 + 0x00000000 + 0x00000085 + 0x00000012 + 0x00000090 + 0x00000200 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000010 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00001017 + 0x00000000 + 0x00000000 + 0x00000000 + 0x104ab098 + 0xe01200b1 + 0x00008000 + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00054000 + 0x00054000 + 0x00000000 + 0x00054000 + 0x00054000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x0000000c + 0x0000000c + 0x0000000c + 0x0000000c + 0x0000000c + 0x0000000c + 0x0000000c + 0x0000000c + 0x100002a0 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc085 + 0x00000505 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x51451420 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0606003f + 0x00000000 + 0x00000000 + 0x00000100 + 0x0139000e + 0x00000000 + 0x00000003 + 0x000042a0 + 0x80002062 + 0x0000000a + >; + }; + + timing-600000000 { + clock-frequency = <600000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73300000>; + nvidia,emc-cfg-2 = <0x0000089d>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200010>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000b61>; + nvidia,emc-mrs-wait-cnt = <0x0127000e>; + nvidia,emc-sel-dpd-ctrl = <0x00040008>; + nvidia,emc-xm2dqspadctrl2 = <0x0121113d>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x0000001b + 0x0000009b + 0x00000000 + 0x00000013 + 0x00000007 + 0x00000007 + 0x0000000b + 0x00000003 + 0x00000010 + 0x00000007 + 0x00000007 + 0x00000002 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x0000000a + 0x00000002 + 0x00000000 + 0x00000003 + 0x0000000b + 0x00070000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000002 + 0x00000012 + 0x00000016 + 0x00000018 + 0x00001208 + 0x00000000 + 0x00000482 + 0x00000002 + 0x0000000d + 0x00000001 + 0x00000000 + 0x00000097 + 0x00000015 + 0x000000a3 + 0x00000200 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000013 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00001248 + 0x00000000 + 0x00000000 + 0x00000000 + 0x104ab098 + 0xe00e00b1 + 0x00008000 + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00048000 + 0x00048000 + 0x00000000 + 0x00048000 + 0x00048000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x0000000d + 0x0000000d + 0x0000000d + 0x0000000d + 0x0000000d + 0x0000000d + 0x0000000d + 0x0000000d + 0x100002a0 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc085 + 0x00000505 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x51451420 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0606003f + 0x00000000 + 0x00000000 + 0x00000100 + 0x0127000e + 0x00000000 + 0x00000003 + 0x000040a0 + 0x800024aa + 0x0000000e + >; + }; + + timing-792000000 { + clock-frequency = <792000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73300000>; + nvidia,emc-cfg-2 = <0x0000089d>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200018>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000d71>; + nvidia,emc-mrs-wait-cnt = <0x00f7000e>; + nvidia,emc-sel-dpd-ctrl = <0x00040000>; + nvidia,emc-xm2dqspadctrl2 = <0x0120113d>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x00000024 + 0x000000cd + 0x00000000 + 0x00000019 + 0x0000000a + 0x00000008 + 0x0000000d + 0x00000004 + 0x00000013 + 0x0000000a + 0x0000000a + 0x00000004 + 0x00000002 + 0x00000000 + 0x00000006 + 0x00000006 + 0x0000000b + 0x00000002 + 0x00000000 + 0x00000002 + 0x0000000d + 0x00080000 + 0x00000004 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000001 + 0x00000014 + 0x00000018 + 0x0000001a + 0x000017e2 + 0x00000000 + 0x000005f8 + 0x00000003 + 0x00000011 + 0x00000001 + 0x00000000 + 0x000000c7 + 0x00000018 + 0x000000d7 + 0x00000200 + 0x00000005 + 0x00000006 + 0x00000005 + 0x00000019 + 0x00000000 + 0x00000008 + 0x00000008 + 0x00001822 + 0x00000000 + 0x00000000 + 0x00000000 + 0x104ab098 + 0xe00700b1 + 0x00008000 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x007fc008 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00034000 + 0x00034000 + 0x00000000 + 0x00034000 + 0x00034000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x100002a0 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc085 + 0x00000000 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x61861820 + 0x00514514 + 0x00514514 + 0x61861800 + 0x0606003f + 0x00000000 + 0x00000000 + 0x00000100 + 0x00f7000e + 0x00000000 + 0x00000004 + 0x00004080 + 0x80003012 + 0x0000000f + >; + }; + + timing-924000000 { + clock-frequency = <924000000>; + + nvidia,emc-auto-cal-config = <0xa1430303>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73300000>; + nvidia,emc-cfg-2 = <0x0000089d>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200020>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000f15>; + nvidia,emc-mrs-wait-cnt = <0x00cd000e>; + nvidia,emc-sel-dpd-ctrl = <0x00040000>; + nvidia,emc-xm2dqspadctrl2 = <0x0120113d>; + nvidia,emc-zcal-cnt-long = <0x0000004c>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x0000002b + 0x000000f0 + 0x00000000 + 0x0000001e + 0x0000000b + 0x00000009 + 0x0000000f + 0x00000005 + 0x00000016 + 0x0000000b + 0x0000000b + 0x00000004 + 0x00000002 + 0x00000000 + 0x00000007 + 0x00000007 + 0x0000000d + 0x00000002 + 0x00000000 + 0x00000002 + 0x0000000f + 0x000a0000 + 0x00000004 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000001 + 0x00000016 + 0x0000001a + 0x0000001c + 0x00001be7 + 0x00000000 + 0x000006f9 + 0x00000004 + 0x00000015 + 0x00000001 + 0x00000000 + 0x000000e7 + 0x0000001b + 0x000000fb + 0x00000200 + 0x00000006 + 0x00000007 + 0x00000006 + 0x0000001e + 0x00000000 + 0x0000000a + 0x0000000a + 0x00001c28 + 0x00000000 + 0x00000000 + 0x00000000 + 0x104ab898 + 0xe00400b1 + 0x00008000 + 0x007f800a + 0x007f800a + 0x007f800a + 0x007f800a + 0x007f800a + 0x007f800a + 0x007f800a + 0x007f800a + 0x007f800a + 0x007f800a + 0x007f800a + 0x007f800a + 0x007f800a + 0x007f800a + 0x007f800a + 0x007f800a + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x0002c000 + 0x0002c000 + 0x00000000 + 0x0002c000 + 0x0002c000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000004 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x100002a0 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc085 + 0x00000000 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x5d75d720 + 0x00514514 + 0x00514514 + 0x5d75d700 + 0x0606003f + 0x00000000 + 0x00000000 + 0x00000128 + 0x00cd000e + 0x00000000 + 0x00000004 + 0x00004080 + 0x800037ea + 0x00000011 + >; + }; + + }; + }; + + memory-controller@0,70019000 { + emc-timings-3 { + nvidia,ram-code = <3>; + + timing-12750000 { + clock-frequency = <12750000>; + + nvidia,emem-configuration = < + 0x40040001 + 0x8000000a + 0x00000001 + 0x00000001 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000003 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0502 + 0x77e30303 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-20400000 { + clock-frequency = <20400000>; + + nvidia,emem-configuration = < + 0x40020001 + 0x80000012 + 0x00000001 + 0x00000001 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000003 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0502 + 0x76230303 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-40800000 { + clock-frequency = <40800000>; + + nvidia,emem-configuration = < + 0xa0000001 + 0x80000017 + 0x00000001 + 0x00000001 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000003 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0502 + 0x74a30303 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-68000000 { + clock-frequency = <68000000>; + + nvidia,emem-configuration = < + 0x00000001 + 0x8000001e + 0x00000001 + 0x00000001 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000003 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0502 + 0x74230403 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-102000000 { + clock-frequency = <102000000>; + + nvidia,emem-configuration = < + 0x08000001 + 0x80000026 + 0x00000001 + 0x00000001 + 0x00000003 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000003 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0503 + 0x73c30504 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-204000000 { + clock-frequency = <204000000>; + + nvidia,emem-configuration = < + 0x01000003 + 0x80000040 + 0x00000001 + 0x00000001 + 0x00000004 + 0x00000002 + 0x00000003 + 0x00000001 + 0x00000003 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000004 + 0x00000006 + 0x06040203 + 0x000a0504 + 0x73840a05 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-300000000 { + clock-frequency = <300000000>; + + nvidia,emem-configuration = < + 0x08000004 + 0x80000040 + 0x00000001 + 0x00000002 + 0x00000007 + 0x00000004 + 0x00000004 + 0x00000001 + 0x00000002 + 0x00000007 + 0x00000002 + 0x00000002 + 0x00000004 + 0x00000006 + 0x06040202 + 0x000b0607 + 0x77450e08 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-396000000 { + clock-frequency = <396000000>; + + nvidia,emem-configuration = < + 0x0f000005 + 0x80000040 + 0x00000001 + 0x00000002 + 0x00000009 + 0x00000005 + 0x00000006 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000002 + 0x00000002 + 0x00000004 + 0x00000006 + 0x06040202 + 0x000d0709 + 0x7586120a + 0x70000f03 + 0x001f0000 + >; + }; + + timing-528000000 { + clock-frequency = <528000000>; + + nvidia,emem-configuration = < + 0x0f000007 + 0x80000040 + 0x00000002 + 0x00000003 + 0x0000000c + 0x00000007 + 0x00000008 + 0x00000001 + 0x00000002 + 0x00000009 + 0x00000002 + 0x00000002 + 0x00000005 + 0x00000006 + 0x06050202 + 0x0010090c + 0x7428180d + 0x70000f03 + 0x001f0000 + >; + }; + + timing-600000000 { + clock-frequency = <600000000>; + + nvidia,emem-configuration = < + 0x00000009 + 0x80000040 + 0x00000003 + 0x00000004 + 0x0000000e + 0x00000009 + 0x0000000a + 0x00000001 + 0x00000003 + 0x0000000b + 0x00000002 + 0x00000002 + 0x00000005 + 0x00000007 + 0x07050202 + 0x00130b0e + 0x73a91b0f + 0x70000f03 + 0x001f0000 + >; + }; + + timing-792000000 { + clock-frequency = <792000000>; + + nvidia,emem-configuration = < + 0x0e00000b + 0x80000040 + 0x00000004 + 0x00000005 + 0x00000013 + 0x0000000c + 0x0000000d + 0x00000002 + 0x00000003 + 0x0000000c + 0x00000002 + 0x00000002 + 0x00000006 + 0x00000008 + 0x08060202 + 0x00170e13 + 0x736c2414 + 0x70000f02 + 0x001f0000 + >; + }; + + timing-924000000 { + clock-frequency = <924000000>; + + nvidia,emem-configuration = < + 0x0e00000d + 0x80000040 + 0x00000005 + 0x00000006 + 0x00000016 + 0x0000000e + 0x0000000f + 0x00000002 + 0x00000004 + 0x0000000e + 0x00000002 + 0x00000002 + 0x00000006 + 0x00000009 + 0x09060202 + 0x001a1016 + 0x734e2a17 + 0x70000f02 + 0x001f0000 + >; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/tegra124-jetson-tk1.dts b/arch/arm/boot/dts/tegra124-jetson-tk1.dts index dbfaba09703a..ed8a8acd3d34 100644 --- a/arch/arm/boot/dts/tegra124-jetson-tk1.dts +++ b/arch/arm/boot/dts/tegra124-jetson-tk1.dts @@ -3,6 +3,8 @@ #include #include "tegra124.dtsi" +#include "tegra124-jetson-tk1-emc.dtsi" + / { model = "NVIDIA Tegra124 Jetson TK1"; compatible = "nvidia,jetson-tk1", "nvidia,tegra124"; @@ -60,35 +62,35 @@ nvidia,pins = "clk_32k_out_pa0"; nvidia,function = "soc"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; }; uart3_cts_n_pa1 { nvidia,pins = "uart3_cts_n_pa1"; - nvidia,function = "uartc"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; dap2_fs_pa2 { nvidia,pins = "dap2_fs_pa2"; nvidia,function = "i2s1"; nvidia,pull = ; nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,enable-input = ; }; dap2_sclk_pa3 { nvidia,pins = "dap2_sclk_pa3"; nvidia,function = "i2s1"; nvidia,pull = ; nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,enable-input = ; }; dap2_din_pa4 { nvidia,pins = "dap2_din_pa4"; nvidia,function = "i2s1"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; }; dap2_dout_pa5 { @@ -96,14 +98,14 @@ nvidia,function = "i2s1"; nvidia,pull = ; nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,enable-input = ; }; sdmmc3_clk_pa6 { nvidia,pins = "sdmmc3_clk_pa6"; nvidia,function = "sdmmc3"; nvidia,pull = ; nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,enable-input = ; }; sdmmc3_cmd_pa7 { nvidia,pins = "sdmmc3_cmd_pa7"; @@ -116,14 +118,14 @@ nvidia,pins = "pb0"; nvidia,function = "uartd"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; }; pb1 { nvidia,pins = "pb1"; nvidia,function = "uartd"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; }; sdmmc3_dat3_pb4 { @@ -156,9 +158,9 @@ }; uart3_rts_n_pc0 { nvidia,pins = "uart3_rts_n_pc0"; - nvidia,function = "uartc"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; uart2_txd_pc2 { @@ -172,7 +174,7 @@ nvidia,pins = "uart2_rxd_pc3"; nvidia,function = "irda"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; }; gen1_i2c_scl_pc4 { @@ -194,44 +196,39 @@ pc7 { nvidia,pins = "pc7"; nvidia,function = "rsvd1"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; pg0 { nvidia,pins = "pg0"; - nvidia,function = "rsvd1"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; pg1 { nvidia,pins = "pg1"; - nvidia,function = "rsvd1"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; pg2 { nvidia,pins = "pg2"; - nvidia,function = "rsvd1"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; pg3 { nvidia,pins = "pg3"; - nvidia,function = "rsvd1"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; pg4 { nvidia,pins = "pg4"; - nvidia,function = "spi4"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; pg5 { nvidia,pins = "pg5"; @@ -251,7 +248,7 @@ nvidia,pins = "pg7"; nvidia,function = "spi4"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; }; ph0 { @@ -270,7 +267,6 @@ }; ph2 { nvidia,pins = "ph2"; - nvidia,function = "gmi"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; @@ -278,57 +274,53 @@ ph3 { nvidia,pins = "ph3"; nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; ph4 { nvidia,pins = "ph4"; - nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; ph5 { nvidia,pins = "ph5"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; ph6 { nvidia,pins = "ph6"; nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; ph7 { nvidia,pins = "ph7"; - nvidia,function = "gmi"; nvidia,pull = ; nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,enable-input = ; }; pi0 { nvidia,pins = "pi0"; - nvidia,function = "rsvd1"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; pi1 { nvidia,pins = "pi1"; - nvidia,function = "rsvd1"; - nvidia,pull = ; + nvidia,pull = ; nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,enable-input = ; }; pi2 { nvidia,pins = "pi2"; nvidia,function = "rsvd4"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; pi3 { @@ -341,22 +333,21 @@ pi4 { nvidia,pins = "pi4"; nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; pi5 { nvidia,pins = "pi5"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; pi6 { nvidia,pins = "pi6"; - nvidia,function = "rsvd1"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; pi7 { @@ -368,23 +359,22 @@ }; pj0 { nvidia,pins = "pj0"; - nvidia,function = "rsvd1"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; pj2 { nvidia,pins = "pj2"; nvidia,function = "rsvd1"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; uart2_cts_n_pj5 { nvidia,pins = "uart2_cts_n_pj5"; nvidia,function = "uartb"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; }; uart2_rts_n_pj6 { @@ -403,35 +393,32 @@ }; pk0 { nvidia,pins = "pk0"; - nvidia,function = "soc"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; pk1 { nvidia,pins = "pk1"; - nvidia,function = "rsvd4"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; pk2 { nvidia,pins = "pk2"; - nvidia,function = "rsvd1"; - nvidia,pull = ; + nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; pk3 { nvidia,pins = "pk3"; nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; pk4 { nvidia,pins = "pk4"; - nvidia,function = "rsvd2"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; @@ -439,13 +426,12 @@ spdif_out_pk5 { nvidia,pins = "spdif_out_pk5"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; spdif_in_pk6 { nvidia,pins = "spdif_in_pk6"; - nvidia,function = "rsvd2"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; @@ -459,17 +445,17 @@ }; dap1_fs_pn0 { nvidia,pins = "dap1_fs_pn0"; - nvidia,function = "i2s0"; + nvidia,function = "rsvd4"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; dap1_din_pn1 { nvidia,pins = "dap1_din_pn1"; - nvidia,function = "i2s0"; + nvidia,function = "rsvd4"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; dap1_dout_pn2 { nvidia,pins = "dap1_dout_pn2"; @@ -480,108 +466,104 @@ }; dap1_sclk_pn3 { nvidia,pins = "dap1_sclk_pn3"; - nvidia,function = "i2s0"; + nvidia,function = "rsvd4"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; usb_vbus_en0_pn4 { nvidia,pins = "usb_vbus_en0_pn4"; nvidia,function = "usb"; - nvidia,pull = ; + nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; - nvidia,open-drain = ; + nvidia,open-drain = ; }; usb_vbus_en1_pn5 { nvidia,pins = "usb_vbus_en1_pn5"; nvidia,function = "usb"; - nvidia,pull = ; + nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; - nvidia,open-drain = ; + nvidia,open-drain = ; }; hdmi_int_pn7 { nvidia,pins = "hdmi_int_pn7"; - nvidia,function = "rsvd1"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; nvidia,rcv-sel = ; }; ulpi_data7_po0 { nvidia,pins = "ulpi_data7_po0"; nvidia,function = "ulpi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; ulpi_data0_po1 { nvidia,pins = "ulpi_data0_po1"; - nvidia,function = "ulpi"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; ulpi_data1_po2 { nvidia,pins = "ulpi_data1_po2"; nvidia,function = "ulpi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; ulpi_data2_po3 { nvidia,pins = "ulpi_data2_po3"; nvidia,function = "ulpi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; ulpi_data3_po4 { nvidia,pins = "ulpi_data3_po4"; - nvidia,function = "ulpi"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; ulpi_data4_po5 { nvidia,pins = "ulpi_data4_po5"; nvidia,function = "ulpi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; ulpi_data5_po6 { nvidia,pins = "ulpi_data5_po6"; nvidia,function = "ulpi"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; ulpi_data6_po7 { nvidia,pins = "ulpi_data6_po7"; nvidia,function = "ulpi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; dap3_fs_pp0 { nvidia,pins = "dap3_fs_pp0"; nvidia,function = "i2s2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; dap3_din_pp1 { nvidia,pins = "dap3_din_pp1"; nvidia,function = "i2s2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; dap3_dout_pp2 { nvidia,pins = "dap3_dout_pp2"; - nvidia,function = "rsvd4"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; @@ -595,91 +577,87 @@ }; dap4_fs_pp4 { nvidia,pins = "dap4_fs_pp4"; - nvidia,function = "i2s3"; + nvidia,function = "rsvd4"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; dap4_din_pp5 { nvidia,pins = "dap4_din_pp5"; - nvidia,function = "i2s3"; + nvidia,function = "rsvd3"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; dap4_dout_pp6 { nvidia,pins = "dap4_dout_pp6"; - nvidia,function = "i2s3"; + nvidia,function = "rsvd4"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; dap4_sclk_pp7 { nvidia,pins = "dap4_sclk_pp7"; - nvidia,function = "i2s3"; + nvidia,function = "rsvd3"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; kb_col0_pq0 { nvidia,pins = "kb_col0_pq0"; - nvidia,function = "rsvd2"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_col1_pq1 { nvidia,pins = "kb_col1_pq1"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; kb_col2_pq2 { nvidia,pins = "kb_col2_pq2"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - kb_col3_pq3 { - nvidia,pins = "kb_col3_pq3"; - nvidia,function = "kbc"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; + kb_col3_pq3 { + nvidia,pins = "kb_col3_pq3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; kb_col4_pq4 { nvidia,pins = "kb_col4_pq4"; nvidia,function = "sdmmc3"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_col5_pq5 { nvidia,pins = "kb_col5_pq5"; - nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_col6_pq6 { nvidia,pins = "kb_col6_pq6"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; kb_col7_pq7 { nvidia,pins = "kb_col7_pq7"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; kb_row0_pr0 { nvidia,pins = "kb_row0_pr0"; - nvidia,function = "rsvd2"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; @@ -687,121 +665,115 @@ kb_row1_pr1 { nvidia,pins = "kb_row1_pr1"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_row2_pr2 { nvidia,pins = "kb_row2_pr2"; - nvidia,function = "rsvd2"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; kb_row3_pr3 { nvidia,pins = "kb_row3_pr3"; - nvidia,function = "sys"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_row4_pr4 { nvidia,pins = "kb_row4_pr4"; - nvidia,function = "rsvd3"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_row5_pr5 { nvidia,pins = "kb_row5_pr5"; nvidia,function = "rsvd3"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_row6_pr6 { nvidia,pins = "kb_row6_pr6"; nvidia,function = "displaya_alt"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_row7_pr7 { nvidia,pins = "kb_row7_pr7"; - nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_row8_ps0 { nvidia,pins = "kb_row8_ps0"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; kb_row9_ps1 { nvidia,pins = "kb_row9_ps1"; - nvidia,function = "rsvd2"; + nvidia,function = "uarta"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; kb_row10_ps2 { nvidia,pins = "kb_row10_ps2"; - nvidia,function = "rsvd2"; + nvidia,function = "uarta"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_row11_ps3 { nvidia,pins = "kb_row11_ps3"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_row12_ps4 { nvidia,pins = "kb_row12_ps4"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_row13_ps5 { nvidia,pins = "kb_row13_ps5"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; kb_row14_ps6 { nvidia,pins = "kb_row14_ps6"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_row15_ps7 { nvidia,pins = "kb_row15_ps7"; - nvidia,function = "soc"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; kb_row16_pt0 { nvidia,pins = "kb_row16_pt0"; - nvidia,function = "rsvd2"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; kb_row17_pt1 { nvidia,pins = "kb_row17_pt1"; - nvidia,function = "rsvd2"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; gen2_i2c_scl_pt5 { nvidia,pins = "gen2_i2c_scl_pt5"; @@ -828,72 +800,63 @@ }; pu0 { nvidia,pins = "pu0"; - nvidia,function = "rsvd4"; nvidia,pull = ; nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,enable-input = ; }; pu1 { nvidia,pins = "pu1"; - nvidia,function = "rsvd1"; - nvidia,pull = ; + nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; pu2 { nvidia,pins = "pu2"; - nvidia,function = "rsvd1"; - nvidia,pull = ; + nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; pu3 { nvidia,pins = "pu3"; - nvidia,function = "gmi"; nvidia,pull = ; nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,enable-input = ; }; pu4 { nvidia,pins = "pu4"; - nvidia,function = "gmi"; nvidia,pull = ; nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,enable-input = ; }; pu5 { nvidia,pins = "pu5"; - nvidia,function = "gmi"; - nvidia,pull = ; + nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; pu6 { nvidia,pins = "pu6"; - nvidia,function = "rsvd3"; - nvidia,pull = ; + nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; pv0 { nvidia,pins = "pv0"; - nvidia,function = "rsvd1"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; pv1 { nvidia,pins = "pv1"; - nvidia,function = "rsvd1"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; sdmmc3_cd_n_pv2 { nvidia,pins = "sdmmc3_cd_n_pv2"; nvidia,function = "sdmmc3"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; }; sdmmc1_wp_n_pv3 { @@ -922,16 +885,16 @@ gpio_w2_aud_pw2 { nvidia,pins = "gpio_w2_aud_pw2"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; gpio_w3_aud_pw3 { nvidia,pins = "gpio_w3_aud_pw3"; nvidia,function = "spi6"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; dap_mclk1_pw4 { nvidia,pins = "dap_mclk1_pw4"; @@ -949,17 +912,17 @@ }; uart3_txd_pw6 { nvidia,pins = "uart3_txd_pw6"; - nvidia,function = "uartc"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; uart3_rxd_pw7 { nvidia,pins = "uart3_rxd_pw7"; - nvidia,function = "uartc"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; dvfs_pwm_px0 { nvidia,pins = "dvfs_pwm_px0"; @@ -970,10 +933,9 @@ }; gpio_x1_aud_px1 { nvidia,pins = "gpio_x1_aud_px1"; - nvidia,function = "rsvd2"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; dvfs_clk_px2 { nvidia,pins = "dvfs_clk_px2"; @@ -985,34 +947,32 @@ gpio_x3_aud_px3 { nvidia,pins = "gpio_x3_aud_px3"; nvidia,function = "rsvd4"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; gpio_x4_aud_px4 { nvidia,pins = "gpio_x4_aud_px4"; - nvidia,function = "gmi"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; gpio_x5_aud_px5 { nvidia,pins = "gpio_x5_aud_px5"; nvidia,function = "rsvd4"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; gpio_x6_aud_px6 { nvidia,pins = "gpio_x6_aud_px6"; nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; gpio_x7_aud_px7 { nvidia,pins = "gpio_x7_aud_px7"; - nvidia,function = "rsvd1"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; @@ -1027,8 +987,8 @@ ulpi_dir_py1 { nvidia,pins = "ulpi_dir_py1"; nvidia,function = "spi1"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; ulpi_nxt_py2 { @@ -1048,44 +1008,44 @@ sdmmc1_dat3_py4 { nvidia,pins = "sdmmc1_dat3_py4"; nvidia,function = "sdmmc1"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; sdmmc1_dat2_py5 { nvidia,pins = "sdmmc1_dat2_py5"; nvidia,function = "sdmmc1"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; sdmmc1_dat1_py6 { nvidia,pins = "sdmmc1_dat1_py6"; nvidia,function = "sdmmc1"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; sdmmc1_dat0_py7 { nvidia,pins = "sdmmc1_dat0_py7"; - nvidia,function = "sdmmc1"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; sdmmc1_clk_pz0 { nvidia,pins = "sdmmc1_clk_pz0"; - nvidia,function = "sdmmc1"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; sdmmc1_cmd_pz1 { nvidia,pins = "sdmmc1_cmd_pz1"; nvidia,function = "sdmmc1"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; pwr_i2c_scl_pz6 { nvidia,pins = "pwr_i2c_scl_pz6"; @@ -1184,7 +1144,6 @@ }; pbb3 { nvidia,pins = "pbb3"; - nvidia,function = "vgp3"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; @@ -1198,21 +1157,18 @@ }; pbb5 { nvidia,pins = "pbb5"; - nvidia,function = "rsvd3"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; pbb6 { nvidia,pins = "pbb6"; - nvidia,function = "rsvd2"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; pbb7 { nvidia,pins = "pbb7"; - nvidia,function = "rsvd2"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; @@ -1226,15 +1182,13 @@ }; pcc1 { nvidia,pins = "pcc1"; - nvidia,function = "rsvd2"; - nvidia,pull = ; + nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; pcc2 { nvidia,pins = "pcc2"; - nvidia,function = "rsvd2"; - nvidia,pull = ; + nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; }; @@ -1248,8 +1202,8 @@ clk2_req_pcc5 { nvidia,pins = "clk2_req_pcc5"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; pex_l0_rst_n_pdd1 { @@ -1262,15 +1216,15 @@ pex_l0_clkreq_n_pdd2 { nvidia,pins = "pex_l0_clkreq_n_pdd2"; nvidia,function = "pe0"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; pex_wake_n_pdd3 { nvidia,pins = "pex_wake_n_pdd3"; nvidia,function = "pe"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; pex_l1_rst_n_pdd5 { @@ -1283,8 +1237,8 @@ pex_l1_clkreq_n_pdd6 { nvidia,pins = "pex_l1_clkreq_n_pdd6"; nvidia,function = "pe1"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; clk3_out_pee0 { @@ -1297,13 +1251,12 @@ clk3_req_pee1 { nvidia,pins = "clk3_req_pee1"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; dap_mclk1_req_pee2 { nvidia,pins = "dap_mclk1_req_pee2"; - nvidia,function = "sata"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; @@ -1314,7 +1267,7 @@ nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; - nvidia,open-drain = ; + nvidia,open-drain = ; }; sdmmc3_clk_lb_out_pee4 { nvidia,pins = "sdmmc3_clk_lb_out_pee4"; @@ -1333,24 +1286,24 @@ dp_hpd_pff0 { nvidia,pins = "dp_hpd_pff0"; nvidia,function = "dp"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; }; usb_vbus_en2_pff1 { nvidia,pins = "usb_vbus_en2_pff1"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; + nvidia,pull = ; + nvidia,tristate = ; nvidia,enable-input = ; nvidia,open-drain = ; }; pff2 { nvidia,pins = "pff2"; nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; nvidia,open-drain = ; }; core_pwr_req { @@ -1362,7 +1315,7 @@ }; cpu_pwr_req { nvidia,pins = "cpu_pwr_req"; - nvidia,function = "rsvd2"; + nvidia,function = "cpu"; nvidia,pull = ; nvidia,tristate = ; nvidia,enable-input = ; @@ -1371,7 +1324,7 @@ nvidia,pins = "pwr_int_n"; nvidia,function = "pmi"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; }; reset_out_n { @@ -1379,7 +1332,7 @@ nvidia,function = "reset_out_n"; nvidia,pull = ; nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,enable-input = ; }; owr { nvidia,pins = "owr"; @@ -1391,9 +1344,9 @@ }; clk_32k_in { nvidia,pins = "clk_32k_in"; - nvidia,function = "rsvd2"; + nvidia,function = "clk"; nvidia,pull = ; - nvidia,tristate = ; + nvidia,tristate = ; nvidia,enable-input = ; }; jtag_rtck { diff --git a/arch/arm/boot/dts/tegra124-nyan-big-emc.dtsi b/arch/arm/boot/dts/tegra124-nyan-big-emc.dtsi new file mode 100644 index 000000000000..1a5748d05dda --- /dev/null +++ b/arch/arm/boot/dts/tegra124-nyan-big-emc.dtsi @@ -0,0 +1,2023 @@ +/ { + clock@0,60006000 { + emc-timings-1 { + nvidia,ram-code = <1>; + + timing-12750000 { + clock-frequency = <12750000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-20400000 { + clock-frequency = <20400000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-40800000 { + clock-frequency = <40800000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-68000000 { + clock-frequency = <68000000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-102000000 { + clock-frequency = <102000000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-204000000 { + clock-frequency = <204000000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-300000000 { + clock-frequency = <300000000>; + nvidia,parent-clock-frequency = <600000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_C>; + clock-names = "emc-parent"; + }; + timing-396000000 { + clock-frequency = <396000000>; + nvidia,parent-clock-frequency = <792000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_M>; + clock-names = "emc-parent"; + }; + /* TODO: Add 528MHz frequency */ + timing-600000000 { + clock-frequency = <600000000>; + nvidia,parent-clock-frequency = <600000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>; + clock-names = "emc-parent"; + }; + timing-792000000 { + clock-frequency = <792000000>; + nvidia,parent-clock-frequency = <792000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>; + clock-names = "emc-parent"; + }; + }; + }; + + emc@0,7001b000 { + emc-timings-1 { + nvidia,ram-code = <1>; + + timing-12750000 { + clock-frequency = <12750000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000c000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000a + 0x00000003 + 0x0000000b + 0x00000000 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x00000060 + 0x00000000 + 0x00000018 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000007 + 0x0000000f + 0x00000005 + 0x00000005 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000000 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000064 + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00004000 + 0x00000000 + 0x00000000 + 0x00004000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000303 + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000007 + 0x00000000 + 0x00000042 + 0x000c000c + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x800001c5 + 0x0000000a + >; + }; + + timing-20400000 { + clock-frequency = <20400000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000c000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000000 + 0x00000005 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000a + 0x00000003 + 0x0000000b + 0x00000000 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x0000009a + 0x00000000 + 0x00000026 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000007 + 0x0000000f + 0x00000006 + 0x00000006 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000000 + 0x00000000 + 0x00000005 + 0x00000005 + 0x000000a0 + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00004000 + 0x00000000 + 0x00000000 + 0x00004000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000303 + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x0000000b + 0x00000000 + 0x00000042 + 0x000c000c + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x8000023a + 0x0000000a + >; + }; + + timing-40800000 { + clock-frequency = <40800000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000c000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000001 + 0x0000000a + 0x00000000 + 0x00000001 + 0x00000000 + 0x00000004 + 0x0000000a + 0x00000003 + 0x0000000b + 0x00000000 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x00000134 + 0x00000000 + 0x0000004d + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000008 + 0x0000000f + 0x0000000c + 0x0000000c + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000000 + 0x00000000 + 0x00000005 + 0x00000005 + 0x0000013f + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00004000 + 0x00000000 + 0x00000000 + 0x00004000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000303 + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000015 + 0x00000000 + 0x00000042 + 0x000c000c + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x80000370 + 0x0000000a + >; + }; + + timing-68000000 { + clock-frequency = <68000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000c000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000003 + 0x00000011 + 0x00000000 + 0x00000002 + 0x00000000 + 0x00000004 + 0x0000000a + 0x00000003 + 0x0000000b + 0x00000000 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x00000202 + 0x00000000 + 0x00000080 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x0000000f + 0x0000000f + 0x00000013 + 0x00000013 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000001 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000213 + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00004000 + 0x00000000 + 0x00000000 + 0x00004000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000303 + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000022 + 0x00000000 + 0x00000042 + 0x000c000c + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x8000050e + 0x0000000a + >; + }; + + timing-102000000 { + clock-frequency = <102000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000c000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000004 + 0x0000001a + 0x00000000 + 0x00000003 + 0x00000001 + 0x00000004 + 0x0000000a + 0x00000003 + 0x0000000b + 0x00000001 + 0x00000001 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x00000304 + 0x00000000 + 0x000000c1 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000018 + 0x0000000f + 0x0000001c + 0x0000001c + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000003 + 0x00000000 + 0x00000005 + 0x00000005 + 0x0000031c + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00004000 + 0x00000000 + 0x00000000 + 0x00004000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000303 + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000033 + 0x00000000 + 0x00000042 + 0x000c000c + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x80000713 + 0x0000000a + >; + }; + + timing-204000000 { + clock-frequency = <204000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x0000088d>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000c000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040008>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x00000009 + 0x00000035 + 0x00000000 + 0x00000007 + 0x00000002 + 0x00000005 + 0x0000000a + 0x00000003 + 0x0000000b + 0x00000002 + 0x00000002 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000004 + 0x00000006 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000003 + 0x0000000d + 0x0000000f + 0x00000011 + 0x00000607 + 0x00000000 + 0x00000181 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000032 + 0x0000000f + 0x00000038 + 0x00000038 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000007 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000638 + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00004000 + 0x00000000 + 0x00000000 + 0x00004000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00090000 + 0x00090000 + 0x00094000 + 0x00094000 + 0x00009400 + 0x00009000 + 0x00009000 + 0x00009000 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000303 + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000066 + 0x00000000 + 0x00000100 + 0x000c000c + 0x00000000 + 0x00000003 + 0x0000d2b3 + 0x80000d22 + 0x0000000a + >; + }; + + timing-300000000 { + clock-frequency = <300000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73340000>; + nvidia,emc-cfg-2 = <0x000008d5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200000>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000321>; + nvidia,emc-mrs-wait-cnt = <0x0174000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x01231339>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x0000000d + 0x0000004c + 0x00000000 + 0x00000009 + 0x00000003 + 0x00000004 + 0x00000008 + 0x00000002 + 0x00000009 + 0x00000003 + 0x00000003 + 0x00000002 + 0x00000002 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000005 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000007 + 0x00020000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000001 + 0x0000000e + 0x00000010 + 0x00000012 + 0x000008e4 + 0x00000000 + 0x00000239 + 0x00000001 + 0x00000008 + 0x00000001 + 0x00000000 + 0x0000004a + 0x0000000e + 0x00000051 + 0x00000200 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000009 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000924 + 0x00000000 + 0x00000000 + 0x00000000 + 0x104ab098 + 0x002c00a0 + 0x00008000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00098000 + 0x00098000 + 0x00000000 + 0x00098000 + 0x00098000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00060000 + 0x00060000 + 0x00060000 + 0x00060000 + 0x00006000 + 0x00006000 + 0x00006000 + 0x00006000 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000101 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x51451420 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000096 + 0x00000000 + 0x00000100 + 0x0174000c + 0x00000000 + 0x00000003 + 0x000052a3 + 0x800012d7 + 0x00000009 + >; + }; + + timing-396000000 { + clock-frequency = <396000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73340000>; + nvidia,emc-cfg-2 = <0x00000895>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200000>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000521>; + nvidia,emc-mrs-wait-cnt = <0x015b000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040008>; + nvidia,emc-xm2dqspadctrl2 = <0x01231339>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x00000012 + 0x00000065 + 0x00000000 + 0x0000000c + 0x00000004 + 0x00000005 + 0x00000008 + 0x00000002 + 0x0000000a + 0x00000004 + 0x00000004 + 0x00000002 + 0x00000002 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000005 + 0x00000002 + 0x00000000 + 0x00000001 + 0x00000008 + 0x00020000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x0000000f + 0x00000010 + 0x00000012 + 0x00000bd1 + 0x00000000 + 0x000002f4 + 0x00000001 + 0x00000008 + 0x00000001 + 0x00000000 + 0x00000063 + 0x0000000f + 0x0000006b + 0x00000200 + 0x00000004 + 0x00000005 + 0x00000004 + 0x0000000d + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000c11 + 0x00000000 + 0x00000000 + 0x00000000 + 0x104ab098 + 0x002c00a0 + 0x00008000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00070000 + 0x00070000 + 0x00000000 + 0x00070000 + 0x00070000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00048000 + 0x00048000 + 0x00048000 + 0x00048000 + 0x00004800 + 0x00004800 + 0x00004800 + 0x00004800 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000101 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x51451420 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x000000c6 + 0x00000000 + 0x00000100 + 0x015b000c + 0x00000000 + 0x00000003 + 0x000052a3 + 0x8000188b + 0x00000009 + >; + }; + + timing-600000000 { + clock-frequency = <600000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73300000>; + nvidia,emc-cfg-2 = <0x0000089d>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200010>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000b61>; + nvidia,emc-mrs-wait-cnt = <0x0128000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040008>; + nvidia,emc-xm2dqspadctrl2 = <0x0121113d>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x0000001c + 0x0000009a + 0x00000000 + 0x00000013 + 0x00000007 + 0x00000007 + 0x0000000b + 0x00000003 + 0x00000010 + 0x00000007 + 0x00000007 + 0x00000002 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x0000000a + 0x00000002 + 0x00000000 + 0x00000003 + 0x0000000b + 0x00070000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000002 + 0x00000012 + 0x00000016 + 0x00000018 + 0x00001208 + 0x00000000 + 0x00000482 + 0x00000002 + 0x0000000d + 0x00000001 + 0x00000000 + 0x00000096 + 0x00000015 + 0x000000a2 + 0x00000200 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000015 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00001249 + 0x00000000 + 0x00000000 + 0x00000000 + 0x104ab098 + 0xe00e00b1 + 0x00008000 + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00048000 + 0x00048000 + 0x00000000 + 0x00048000 + 0x00048000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x00000004 + 0x00000002 + 0x00000005 + 0x00000006 + 0x00000003 + 0x00000006 + 0x00000005 + 0x00000004 + 0x00000004 + 0x00000002 + 0x00000005 + 0x00000006 + 0x00000003 + 0x00000006 + 0x00000005 + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x100002a0 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc085 + 0x00000101 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x51451420 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0606003f + 0x00000000 + 0x00000000 + 0x00000100 + 0x0128000c + 0x00000000 + 0x00000003 + 0x000040a0 + 0x800024aa + 0x0000000e + >; + }; + + timing-792000000 { + clock-frequency = <792000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73300000>; + nvidia,emc-cfg-2 = <0x0080089d>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200418>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000d71>; + nvidia,emc-mrs-wait-cnt = <0x00f8000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040000>; + nvidia,emc-xm2dqspadctrl2 = <0x0120113d>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x00000025 + 0x000000cc + 0x00000000 + 0x0000001a + 0x00000009 + 0x00000008 + 0x0000000d + 0x00000004 + 0x00000013 + 0x00000009 + 0x00000009 + 0x00000003 + 0x00000002 + 0x00000000 + 0x00000006 + 0x00000006 + 0x0000000b + 0x00000002 + 0x00000000 + 0x00000002 + 0x0000000d + 0x00080000 + 0x00000004 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000001 + 0x00000014 + 0x00000018 + 0x0000001a + 0x000017e2 + 0x00000000 + 0x000005f8 + 0x00000003 + 0x00000011 + 0x00000001 + 0x00000000 + 0x000000c6 + 0x00000018 + 0x000000d6 + 0x00000200 + 0x00000005 + 0x00000006 + 0x00000005 + 0x0000001d + 0x00000000 + 0x00000008 + 0x00000008 + 0x00001822 + 0x00000000 + 0x80000005 + 0x00000000 + 0x104ab198 + 0xe00700b1 + 0x00008000 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000005 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00034000 + 0x00034000 + 0x00000000 + 0x00034000 + 0x00034000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000008 + 0x00000008 + 0x00000005 + 0x00000009 + 0x00000009 + 0x00000007 + 0x00000009 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000005 + 0x00000009 + 0x00000009 + 0x00000007 + 0x00000009 + 0x00000008 + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x100002a0 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc085 + 0x00000101 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x61861820 + 0x00514514 + 0x00514514 + 0x61861800 + 0x0606003f + 0x00000000 + 0x00000000 + 0x00000100 + 0x00f8000c + 0x00000007 + 0x00000004 + 0x00004080 + 0x80003012 + 0x0000000f + >; + }; + + }; + }; + + memory-controller@0,70019000 { + emc-timings-1 { + nvidia,ram-code = <1>; + + + timing-12750000 { + clock-frequency = <12750000>; + + nvidia,emem-configuration = < + 0x40040001 + 0x8000000a + 0x00000001 + 0x00000001 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0402 + 0x77e30303 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-20400000 { + clock-frequency = <20400000>; + + nvidia,emem-configuration = < + 0x40020001 + 0x80000012 + 0x00000001 + 0x00000001 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0402 + 0x76230303 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-40800000 { + clock-frequency = <40800000>; + + nvidia,emem-configuration = < + 0xa0000001 + 0x80000017 + 0x00000001 + 0x00000001 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0402 + 0x74a30303 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-68000000 { + clock-frequency = <68000000>; + + nvidia,emem-configuration = < + 0x00000001 + 0x8000001e + 0x00000001 + 0x00000001 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0402 + 0x74230403 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-102000000 { + clock-frequency = <102000000>; + + nvidia,emem-configuration = < + 0x08000001 + 0x80000026 + 0x00000001 + 0x00000001 + 0x00000003 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0403 + 0x73c30504 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-204000000 { + clock-frequency = <204000000>; + + nvidia,emem-configuration = < + 0x01000003 + 0x80000040 + 0x00000001 + 0x00000001 + 0x00000005 + 0x00000002 + 0x00000004 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000004 + 0x00000006 + 0x06040203 + 0x000a0405 + 0x73840a06 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-300000000 { + clock-frequency = <300000000>; + + nvidia,emem-configuration = < + 0x08000004 + 0x80000040 + 0x00000001 + 0x00000002 + 0x00000007 + 0x00000004 + 0x00000005 + 0x00000001 + 0x00000002 + 0x00000007 + 0x00000002 + 0x00000002 + 0x00000004 + 0x00000006 + 0x06040202 + 0x000b0607 + 0x77450e08 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-396000000 { + clock-frequency = <396000000>; + + nvidia,emem-configuration = < + 0x0f000005 + 0x80000040 + 0x00000001 + 0x00000002 + 0x00000009 + 0x00000005 + 0x00000007 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000002 + 0x00000002 + 0x00000004 + 0x00000006 + 0x06040202 + 0x000d0709 + 0x7586120a + 0x70000f03 + 0x001f0000 + >; + }; + + timing-600000000 { + clock-frequency = <600000000>; + + nvidia,emem-configuration = < + 0x00000009 + 0x80000040 + 0x00000003 + 0x00000004 + 0x0000000e + 0x00000009 + 0x0000000b + 0x00000001 + 0x00000003 + 0x0000000b + 0x00000002 + 0x00000002 + 0x00000005 + 0x00000007 + 0x07050202 + 0x00130b0e + 0x73a91b0f + 0x70000f03 + 0x001f0000 + >; + }; + + timing-792000000 { + clock-frequency = <792000000>; + + nvidia,emem-configuration = < + 0x0e00000b + 0x80000040 + 0x00000004 + 0x00000005 + 0x00000013 + 0x0000000c + 0x0000000f + 0x00000002 + 0x00000003 + 0x0000000c + 0x00000002 + 0x00000002 + 0x00000006 + 0x00000008 + 0x08060202 + 0x00160d13 + 0x734c2414 + 0x70000f02 + 0x001f0000 + >; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts b/arch/arm/boot/dts/tegra124-nyan-big.dts index 004e8e4e1c04..2d21253ea4e3 100644 --- a/arch/arm/boot/dts/tegra124-nyan-big.dts +++ b/arch/arm/boot/dts/tegra124-nyan-big.dts @@ -1,952 +1,13 @@ /dts-v1/; -#include -#include "tegra124.dtsi" +#include "tegra124-nyan.dtsi" + +#include "tegra124-nyan-big-emc.dtsi" / { model = "Acer Chromebook 13 CB5-311"; compatible = "google,nyan-big", "nvidia,tegra124"; - aliases { - rtc0 = "/i2c@0,7000d000/pmic@40"; - rtc1 = "/rtc@0,7000e000"; - serial0 = &uarta; - }; - - memory { - reg = <0x0 0x80000000 0x0 0x80000000>; - }; - - host1x@0,50000000 { - hdmi@0,54280000 { - status = "okay"; - - vdd-supply = <&vdd_3v3_hdmi>; - pll-supply = <&vdd_hdmi_pll>; - hdmi-supply = <&vdd_5v0_hdmi>; - - nvidia,ddc-i2c-bus = <&hdmi_ddc>; - nvidia,hpd-gpio = - <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>; - }; - - sor@0,54540000 { - status = "okay"; - - nvidia,dpaux = <&dpaux>; - nvidia,panel = <&panel>; - }; - - dpaux@0,545c0000 { - vdd-supply = <&vdd_3v3_panel>; - status = "okay"; - }; - }; - - pinmux@0,70000868 { - pinctrl-names = "default"; - pinctrl-0 = <&pinmux_default>; - - pinmux_default: common { - dap_mclk1_pw4 { - nvidia,pins = "dap_mclk1_pw4"; - nvidia,function = "extperiph1"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - dap2_din_pa4 { - nvidia,pins = "dap2_din_pa4"; - nvidia,function = "i2s1"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - dap2_dout_pa5 { - nvidia,pins = "dap2_dout_pa5", - "dap2_fs_pa2", - "dap2_sclk_pa3"; - nvidia,function = "i2s1"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - dvfs_pwm_px0 { - nvidia,pins = "dvfs_pwm_px0", - "dvfs_clk_px2"; - nvidia,function = "cldvfs"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - ulpi_clk_py0 { - nvidia,pins = "ulpi_clk_py0", - "ulpi_nxt_py2", - "ulpi_stp_py3"; - nvidia,function = "spi1"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - ulpi_dir_py1 { - nvidia,pins = "ulpi_dir_py1"; - nvidia,function = "spi1"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - cam_i2c_scl_pbb1 { - nvidia,pins = "cam_i2c_scl_pbb1", - "cam_i2c_sda_pbb2"; - nvidia,function = "i2c3"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,lock = ; - nvidia,open-drain = ; - }; - gen2_i2c_scl_pt5 { - nvidia,pins = "gen2_i2c_scl_pt5", - "gen2_i2c_sda_pt6"; - nvidia,function = "i2c2"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,lock = ; - nvidia,open-drain = ; - }; - pg4 { - nvidia,pins = "pg4", - "pg5", - "pg6", - "pi3"; - nvidia,function = "spi4"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - pg7 { - nvidia,pins = "pg7"; - nvidia,function = "spi4"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - ph1 { - nvidia,pins = "ph1"; - nvidia,function = "pwm1"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - pk0 { - nvidia,pins = "pk0", - "kb_row15_ps7", - "clk_32k_out_pa0"; - nvidia,function = "soc"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - sdmmc1_clk_pz0 { - nvidia,pins = "sdmmc1_clk_pz0"; - nvidia,function = "sdmmc1"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - sdmmc1_cmd_pz1 { - nvidia,pins = "sdmmc1_cmd_pz1", - "sdmmc1_dat0_py7", - "sdmmc1_dat1_py6", - "sdmmc1_dat2_py5", - "sdmmc1_dat3_py4"; - nvidia,function = "sdmmc1"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - sdmmc3_clk_pa6 { - nvidia,pins = "sdmmc3_clk_pa6"; - nvidia,function = "sdmmc3"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - sdmmc3_cmd_pa7 { - nvidia,pins = "sdmmc3_cmd_pa7", - "sdmmc3_dat0_pb7", - "sdmmc3_dat1_pb6", - "sdmmc3_dat2_pb5", - "sdmmc3_dat3_pb4", - "kb_col4_pq4", - "sdmmc3_clk_lb_out_pee4", - "sdmmc3_clk_lb_in_pee5", - "sdmmc3_cd_n_pv2"; - nvidia,function = "sdmmc3"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - sdmmc4_clk_pcc4 { - nvidia,pins = "sdmmc4_clk_pcc4"; - nvidia,function = "sdmmc4"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - sdmmc4_cmd_pt7 { - nvidia,pins = "sdmmc4_cmd_pt7", - "sdmmc4_dat0_paa0", - "sdmmc4_dat1_paa1", - "sdmmc4_dat2_paa2", - "sdmmc4_dat3_paa3", - "sdmmc4_dat4_paa4", - "sdmmc4_dat5_paa5", - "sdmmc4_dat6_paa6", - "sdmmc4_dat7_paa7"; - nvidia,function = "sdmmc4"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - pwr_i2c_scl_pz6 { - nvidia,pins = "pwr_i2c_scl_pz6", - "pwr_i2c_sda_pz7"; - nvidia,function = "i2cpwr"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,lock = ; - nvidia,open-drain = ; - }; - jtag_rtck { - nvidia,pins = "jtag_rtck"; - nvidia,function = "rtck"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - clk_32k_in { - nvidia,pins = "clk_32k_in"; - nvidia,function = "clk"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - core_pwr_req { - nvidia,pins = "core_pwr_req"; - nvidia,function = "pwron"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - cpu_pwr_req { - nvidia,pins = "cpu_pwr_req"; - nvidia,function = "cpu"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - pwr_int_n { - nvidia,pins = "pwr_int_n"; - nvidia,function = "pmi"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - reset_out_n { - nvidia,pins = "reset_out_n"; - nvidia,function = "reset_out_n"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - clk3_out_pee0 { - nvidia,pins = "clk3_out_pee0"; - nvidia,function = "extperiph3"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - gen1_i2c_sda_pc5 { - nvidia,pins = "gen1_i2c_sda_pc5", - "gen1_i2c_scl_pc4"; - nvidia,function = "i2c1"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,lock = ; - nvidia,open-drain = ; - }; - hdmi_cec_pee3 { - nvidia,pins = "hdmi_cec_pee3"; - nvidia,function = "cec"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,lock = ; - nvidia,open-drain = ; - }; - hdmi_int_pn7 { - nvidia,pins = "hdmi_int_pn7"; - nvidia,function = "rsvd1"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - }; - ddc_scl_pv4 { - nvidia,pins = "ddc_scl_pv4", - "ddc_sda_pv5"; - nvidia,function = "i2c4"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,lock = ; - nvidia,rcv-sel = ; - }; - kb_row10_ps2 { - nvidia,pins = "kb_row10_ps2"; - nvidia,function = "uarta"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - kb_row9_ps1 { - nvidia,pins = "kb_row9_ps1"; - nvidia,function = "uarta"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - usb_vbus_en0_pn4 { - nvidia,pins = "usb_vbus_en0_pn4", - "usb_vbus_en1_pn5"; - nvidia,function = "usb"; - nvidia,enable-input = ; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,lock = ; - nvidia,open-drain = ; - }; - drive_sdio1 { - nvidia,pins = "drive_sdio1"; - nvidia,high-speed-mode = ; - nvidia,schmitt = ; - nvidia,pull-down-strength = <36>; - nvidia,pull-up-strength = <20>; - nvidia,slew-rate-rising = ; - nvidia,slew-rate-falling = ; - }; - drive_sdio3 { - nvidia,pins = "drive_sdio3"; - nvidia,high-speed-mode = ; - nvidia,schmitt = ; - nvidia,pull-down-strength = <22>; - nvidia,pull-up-strength = <36>; - nvidia,slew-rate-rising = ; - nvidia,slew-rate-falling = ; - }; - drive_gma { - nvidia,pins = "drive_gma"; - nvidia,high-speed-mode = ; - nvidia,schmitt = ; - nvidia,pull-down-strength = <2>; - nvidia,pull-up-strength = <1>; - nvidia,slew-rate-rising = ; - nvidia,slew-rate-falling = ; - nvidia,drive-type = <1>; - }; - codec_irq_l { - nvidia,pins = "ph4"; - nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - lcd_bl_en { - nvidia,pins = "ph2"; - nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - touch_irq_l { - nvidia,pins = "gpio_w3_aud_pw3"; - nvidia,function = "spi6"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - tpm_davint_l { - nvidia,pins = "ph6"; - nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - ts_irq_l { - nvidia,pins = "pk2"; - nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - ts_reset_l { - nvidia,pins = "pk4"; - nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - ts_shdn_l { - nvidia,pins = "pk1"; - nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - ph7 { - nvidia,pins = "ph7"; - nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - kb_col0_ap { - nvidia,pins = "kb_col0_pq0"; - nvidia,function = "rsvd4"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - lid_open { - nvidia,pins = "kb_row4_pr4"; - nvidia,function = "rsvd3"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - en_vdd_sd { - nvidia,pins = "kb_row0_pr0"; - nvidia,function = "rsvd4"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - ac_ok { - nvidia,pins = "pj0"; - nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - sensor_irq_l { - nvidia,pins = "pi6"; - nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - wifi_en { - nvidia,pins = "gpio_x7_aud_px7"; - nvidia,function = "rsvd4"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - en_vdd_bl { - nvidia,pins = "dap3_dout_pp2"; - nvidia,function = "i2s2"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - en_vdd_hdmi { - nvidia,pins = "spdif_in_pk6"; - nvidia,function = "spdif"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - soc_warm_reset_l { - nvidia,pins = "pi5"; - nvidia,function = "gmi"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - hp_det_l { - nvidia,pins = "pi7"; - nvidia,function = "rsvd1"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - mic_det_l { - nvidia,pins = "kb_row7_pr7"; - nvidia,function = "rsvd2"; - nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; - }; - }; - }; - - serial@0,70006000 { - /* Debug connector on the bottom of the board near SD card. */ - status = "okay"; - }; - - pwm@0,7000a000 { - status = "okay"; - }; - - i2c@0,7000c000 { - status = "okay"; - clock-frequency = <100000>; - - acodec: audio-codec@10 { - compatible = "maxim,max98090"; - reg = <0x10>; - interrupt-parent = <&gpio>; - interrupts = ; - }; - - temperature-sensor@4c { - compatible = "ti,tmp451"; - reg = <0x4c>; - interrupt-parent = <&gpio>; - interrupts = ; - - #thermal-sensor-cells = <1>; - }; - }; - - i2c@0,7000c400 { - status = "okay"; - clock-frequency = <100000>; - }; - - i2c@0,7000c500 { - status = "okay"; - clock-frequency = <400000>; - - tpm@20 { - compatible = "infineon,slb9645tt"; - reg = <0x20>; - }; - }; - - hdmi_ddc: i2c@0,7000c700 { - status = "okay"; - clock-frequency = <100000>; - }; - - i2c@0,7000d000 { - status = "okay"; - clock-frequency = <400000>; - - pmic: pmic@40 { - compatible = "ams,as3722"; - reg = <0x40>; - interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; - - ams,system-power-controller; - - #interrupt-cells = <2>; - interrupt-controller; - - gpio-controller; - #gpio-cells = <2>; - - pinctrl-names = "default"; - pinctrl-0 = <&as3722_default>; - - as3722_default: pinmux { - gpio0 { - pins = "gpio0"; - function = "gpio"; - bias-pull-down; - }; - - gpio1 { - pins = "gpio1"; - function = "gpio"; - bias-pull-up; - }; - - gpio2_4_7 { - pins = "gpio2", "gpio4", "gpio7"; - function = "gpio"; - bias-pull-up; - }; - - gpio3_6 { - pins = "gpio3", "gpio6"; - bias-high-impedance; - }; - - gpio5 { - pins = "gpio5"; - function = "clk32k-out"; - bias-pull-down; - }; - }; - - regulators { - vsup-sd2-supply = <&vdd_5v0_sys>; - vsup-sd3-supply = <&vdd_5v0_sys>; - vsup-sd4-supply = <&vdd_5v0_sys>; - vsup-sd5-supply = <&vdd_5v0_sys>; - vin-ldo0-supply = <&vdd_1v35_lp0>; - vin-ldo1-6-supply = <&vdd_3v3_run>; - vin-ldo2-5-7-supply = <&vddio_1v8>; - vin-ldo3-4-supply = <&vdd_3v3_sys>; - vin-ldo9-10-supply = <&vdd_5v0_sys>; - vin-ldo11-supply = <&vdd_3v3_run>; - - sd0 { - regulator-name = "+VDD_CPU_AP"; - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <1350000>; - regulator-min-microamp = <3500000>; - regulator-max-microamp = <3500000>; - regulator-always-on; - regulator-boot-on; - ams,ext-control = <2>; - }; - - sd1 { - regulator-name = "+VDD_CORE"; - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <1350000>; - regulator-min-microamp = <2500000>; - regulator-max-microamp = <4000000>; - regulator-always-on; - regulator-boot-on; - ams,ext-control = <1>; - }; - - vdd_1v35_lp0: sd2 { - regulator-name = "+1.35V_LP0(sd2)"; - regulator-min-microvolt = <1350000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-boot-on; - }; - - sd3 { - regulator-name = "+1.35V_LP0(sd3)"; - regulator-min-microvolt = <1350000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_1v05_run: sd4 { - regulator-name = "+1.05V_RUN"; - regulator-min-microvolt = <1050000>; - regulator-max-microvolt = <1050000>; - }; - - vddio_1v8: sd5 { - regulator-name = "+1.8V_VDDIO"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-boot-on; - regulator-always-on; - }; - - sd6 { - regulator-name = "+VDD_GPU_AP"; - regulator-min-microvolt = <650000>; - regulator-max-microvolt = <1200000>; - regulator-min-microamp = <3500000>; - regulator-max-microamp = <3500000>; - regulator-boot-on; - regulator-always-on; - }; - - ldo0 { - regulator-name = "+1.05V_RUN_AVDD"; - regulator-min-microvolt = <1050000>; - regulator-max-microvolt = <1050000>; - regulator-boot-on; - regulator-always-on; - ams,ext-control = <1>; - }; - - ldo1 { - regulator-name = "+1.8V_RUN_CAM"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - - ldo2 { - regulator-name = "+1.2V_GEN_AVDD"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-boot-on; - regulator-always-on; - }; - - ldo3 { - regulator-name = "+1.00V_LP0_VDD_RTC"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-boot-on; - regulator-always-on; - ams,enable-tracking; - }; - - vdd_run_cam: ldo4 { - regulator-name = "+3.3V_RUN_CAM"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - }; - - ldo5 { - regulator-name = "+1.2V_RUN_CAM_FRONT"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - }; - - vddio_sdmmc3: ldo6 { - regulator-name = "+VDDIO_SDMMC3"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - }; - - ldo7 { - regulator-name = "+1.05V_RUN_CAM_REAR"; - regulator-min-microvolt = <1050000>; - regulator-max-microvolt = <1050000>; - }; - - ldo9 { - regulator-name = "+2.8V_RUN_TOUCH"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - }; - - ldo10 { - regulator-name = "+2.8V_RUN_CAM_AF"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - }; - - ldo11 { - regulator-name = "+1.8V_RUN_VPP_FUSE"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - }; - }; - }; - - spi@0,7000d400 { - status = "okay"; - - cros_ec: cros-ec@0 { - compatible = "google,cros-ec-spi"; - spi-max-frequency = <3000000>; - interrupt-parent = <&gpio>; - interrupts = ; - reg = <0>; - - google,cros-ec-spi-msg-delay = <2000>; - - i2c-tunnel { - compatible = "google,cros-ec-i2c-tunnel"; - #address-cells = <1>; - #size-cells = <0>; - - google,remote-bus = <0>; - - charger: bq24735@9 { - compatible = "ti,bq24735"; - reg = <0x9>; - interrupt-parent = <&gpio>; - interrupts = ; - ti,ac-detect-gpios = <&gpio - TEGRA_GPIO(J, 0) - GPIO_ACTIVE_HIGH>; - }; - - battery: sbs-battery@b { - compatible = "sbs,sbs-battery"; - reg = <0xb>; - sbs,i2c-retry-count = <2>; - sbs,poll-retry-count = <10>; - power-supplies = <&charger>; - }; - }; - }; - }; - - spi@0,7000da00 { - status = "okay"; - spi-max-frequency = <25000000>; - - flash@0 { - compatible = "winbond,w25q32dw"; - reg = <0>; - }; - }; - - pmc@0,7000e400 { - nvidia,invert-interrupt; - nvidia,suspend-mode = <0>; - nvidia,cpu-pwr-good-time = <500>; - nvidia,cpu-pwr-off-time = <300>; - nvidia,core-pwr-good-time = <641 3845>; - nvidia,core-pwr-off-time = <61036>; - nvidia,core-power-req-active-high; - nvidia,sys-clock-req-active-high; - }; - - hda@0,70030000 { - status = "okay"; - }; - - sdhci@0,700b0000 { /* WiFi/BT on this bus */ - status = "okay"; - power-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_HIGH>; - bus-width = <4>; - no-1-8-v; - non-removable; - }; - - sdhci@0,700b0400 { /* SD Card on this bus */ - status = "okay"; - cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>; - power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>; - wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>; - bus-width = <4>; - no-1-8-v; - vqmmc-supply = <&vddio_sdmmc3>; - }; - - sdhci@0,700b0600 { /* eMMC on this bus */ - status = "okay"; - bus-width = <8>; - no-1-8-v; - non-removable; - }; - - ahub@0,70300000 { - i2s@0,70301100 { - status = "okay"; - }; - }; - - usb@0,7d000000 { /* Rear external USB port. */ - status = "okay"; - }; - - usb-phy@0,7d000000 { - status = "okay"; - vbus-supply = <&vdd_usb1_vbus>; - }; - - usb@0,7d004000 { /* Internal webcam. */ - status = "okay"; - }; - - usb-phy@0,7d004000 { - status = "okay"; - vbus-supply = <&vdd_run_cam>; - }; - - usb@0,7d008000 { /* Left external USB port. */ - status = "okay"; - }; - - usb-phy@0,7d008000 { - status = "okay"; - vbus-supply = <&vdd_usb3_vbus>; - }; - - backlight: backlight { - compatible = "pwm-backlight"; - - enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>; - power-supply = <&vdd_led>; - pwms = <&pwm 1 1000000>; - - default-brightness-level = <224>; - brightness-levels = - < 0 1 2 3 4 5 6 7 - 8 9 10 11 12 13 14 15 - 16 17 18 19 20 21 22 23 - 24 25 26 27 28 29 30 31 - 32 33 34 35 36 37 38 39 - 40 41 42 43 44 45 46 47 - 48 49 50 51 52 53 54 55 - 56 57 58 59 60 61 62 63 - 64 65 66 67 68 69 70 71 - 72 73 74 75 76 77 78 79 - 80 81 82 83 84 85 86 87 - 88 89 90 91 92 93 94 95 - 96 97 98 99 100 101 102 103 - 104 105 106 107 108 109 110 111 - 112 113 114 115 116 117 118 119 - 120 121 122 123 124 125 126 127 - 128 129 130 131 132 133 134 135 - 136 137 138 139 140 141 142 143 - 144 145 146 147 148 149 150 151 - 152 153 154 155 156 157 158 159 - 160 161 162 163 164 165 166 167 - 168 169 170 171 172 173 174 175 - 176 177 178 179 180 181 182 183 - 184 185 186 187 188 189 190 191 - 192 193 194 195 196 197 198 199 - 200 201 202 203 204 205 206 207 - 208 209 210 211 212 213 214 215 - 216 217 218 219 220 221 222 223 - 224 225 226 227 228 229 230 231 - 232 233 234 235 236 237 238 239 - 240 241 242 243 244 245 246 247 - 248 249 250 251 252 253 254 255 - 256>; - }; - - clocks { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - - clk32k_in: clock@0 { - compatible = "fixed-clock"; - reg = <0>; - #clock-cells = <0>; - clock-frequency = <32768>; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - - lid { - label = "Lid"; - gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>; - linux,input-type = <5>; - linux,code = ; - debounce-interval = <1>; - gpio-key,wakeup; - }; - - power { - label = "Power"; - gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>; - linux,code = ; - debounce-interval = <30>; - gpio-key,wakeup; - }; - }; - panel: panel { compatible = "auo,b133xtn01"; @@ -954,186 +15,1324 @@ ddc-i2c-bus = <&dpaux>; }; - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - - vdd_mux: regulator@0 { - compatible = "regulator-fixed"; - reg = <0>; - regulator-name = "+VDD_MUX"; - regulator-min-microvolt = <12000000>; - regulator-max-microvolt = <12000000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_5v0_sys: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "+5V_SYS"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <&vdd_mux>; - }; - - vdd_3v3_sys: regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - regulator-name = "+3.3V_SYS"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - vin-supply = <&vdd_mux>; - }; - - vdd_3v3_run: regulator@3 { - compatible = "regulator-fixed"; - reg = <3>; - regulator-name = "+3.3V_RUN"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - gpio = <&pmic 1 GPIO_ACTIVE_HIGH>; - enable-active-high; - vin-supply = <&vdd_3v3_sys>; - }; - - vdd_3v3_hdmi: regulator@4 { - compatible = "regulator-fixed"; - reg = <4>; - regulator-name = "+3.3V_AVDD_HDMI_AP_GATED"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - vin-supply = <&vdd_3v3_run>; - }; - - vdd_led: regulator@5 { - compatible = "regulator-fixed"; - reg = <5>; - regulator-name = "+VDD_LED"; - gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>; - enable-active-high; - vin-supply = <&vdd_mux>; - }; - - vdd_5v0_ts: regulator@6 { - compatible = "regulator-fixed"; - reg = <6>; - regulator-name = "+5V_VDD_TS_SW"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-boot-on; - gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>; - enable-active-high; - vin-supply = <&vdd_5v0_sys>; - }; - - vdd_usb1_vbus: regulator@7 { - compatible = "regulator-fixed"; - reg = <7>; - regulator-name = "+5V_USB_HS"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>; - enable-active-high; - gpio-open-drain; - vin-supply = <&vdd_5v0_sys>; - }; - - vdd_usb3_vbus: regulator@8 { - compatible = "regulator-fixed"; - reg = <8>; - regulator-name = "+5V_USB_SS"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>; - enable-active-high; - gpio-open-drain; - vin-supply = <&vdd_5v0_sys>; - }; - - vdd_3v3_panel: regulator@9 { - compatible = "regulator-fixed"; - reg = <9>; - regulator-name = "+3.3V_PANEL"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&pmic 4 GPIO_ACTIVE_HIGH>; - enable-active-high; - vin-supply = <&vdd_3v3_run>; - }; - - vdd_3v3_lp0: regulator@10 { - compatible = "regulator-fixed"; - reg = <10>; - regulator-name = "+3.3V_LP0"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - /* - * TODO: find a way to wire this up with the USB EHCI - * controllers so that it can be enabled on demand. - */ - regulator-always-on; - gpio = <&pmic 2 GPIO_ACTIVE_HIGH>; - enable-active-high; - vin-supply = <&vdd_3v3_sys>; - }; - - vdd_hdmi_pll: regulator@11 { - compatible = "regulator-fixed"; - reg = <11>; - regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL"; - regulator-min-microvolt = <1050000>; - regulator-max-microvolt = <1050000>; - gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>; - vin-supply = <&vdd_1v05_run>; - }; - - vdd_5v0_hdmi: regulator@12 { - compatible = "regulator-fixed"; - reg = <12>; - regulator-name = "+5V_HDMI_CON"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>; - enable-active-high; - vin-supply = <&vdd_5v0_sys>; - }; + sdhci@0,700b0400 { /* SD Card on this bus */ + wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>; }; sound { compatible = "nvidia,tegra-audio-max98090-nyan-big", + "nvidia,tegra-audio-max98090-nyan", "nvidia,tegra-audio-max98090"; - nvidia,model = "Acer Chromebook 13"; + nvidia,model = "GoogleNyanBig"; + }; - nvidia,audio-routing = - "Headphones", "HPR", - "Headphones", "HPL", - "Speakers", "SPKR", - "Speakers", "SPKL", - "Mic Jack", "MICBIAS", - "DMICL", "Int Mic", - "DMICR", "Int Mic", - "IN34", "Mic Jack"; + pinmux@0,70000868 { + pinctrl-names = "default"; + pinctrl-0 = <&pinmux_default>; - nvidia,i2s-controller = <&tegra_i2s1>; - nvidia,audio-codec = <&acodec>; - - clocks = <&tegra_car TEGRA124_CLK_PLL_A>, - <&tegra_car TEGRA124_CLK_PLL_A_OUT0>, - <&tegra_car TEGRA124_CLK_EXTERN1>; - clock-names = "pll_a", "pll_a_out0", "mclk"; - - nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>; - nvidia,mic-det-gpios = - <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>; + pinmux_default: common { + clk_32k_out_pa0 { + nvidia,pins = "clk_32k_out_pa0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart3_cts_n_pa1 { + nvidia,pins = "uart3_cts_n_pa1"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap2_fs_pa2 { + nvidia,pins = "dap2_fs_pa2"; + nvidia,function = "i2s1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap2_sclk_pa3 { + nvidia,pins = "dap2_sclk_pa3"; + nvidia,function = "i2s1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap2_din_pa4 { + nvidia,pins = "dap2_din_pa4"; + nvidia,function = "i2s1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap2_dout_pa5 { + nvidia,pins = "dap2_dout_pa5"; + nvidia,function = "i2s1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_clk_pa6 { + nvidia,pins = "sdmmc3_clk_pa6"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_cmd_pa7 { + nvidia,pins = "sdmmc3_cmd_pa7"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pb0 { + nvidia,pins = "pb0"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pb1 { + nvidia,pins = "pb1"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat3_pb4 { + nvidia,pins = "sdmmc3_dat3_pb4"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat2_pb5 { + nvidia,pins = "sdmmc3_dat2_pb5"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat1_pb6 { + nvidia,pins = "sdmmc3_dat1_pb6"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat0_pb7 { + nvidia,pins = "sdmmc3_dat0_pb7"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart3_rts_n_pc0 { + nvidia,pins = "uart3_rts_n_pc0"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart2_txd_pc2 { + nvidia,pins = "uart2_txd_pc2"; + nvidia,function = "irda"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart2_rxd_pc3 { + nvidia,pins = "uart2_rxd_pc3"; + nvidia,function = "irda"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gen1_i2c_scl_pc4 { + nvidia,pins = "gen1_i2c_scl_pc4"; + nvidia,function = "i2c1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + gen1_i2c_sda_pc5 { + nvidia,pins = "gen1_i2c_sda_pc5"; + nvidia,function = "i2c1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + pc7 { + nvidia,pins = "pc7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg0 { + nvidia,pins = "pg0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg1 { + nvidia,pins = "pg1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg2 { + nvidia,pins = "pg2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg3 { + nvidia,pins = "pg3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg4 { + nvidia,pins = "pg4"; + nvidia,function = "spi4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg5 { + nvidia,pins = "pg5"; + nvidia,function = "spi4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg6 { + nvidia,pins = "pg6"; + nvidia,function = "spi4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg7 { + nvidia,pins = "pg7"; + nvidia,function = "spi4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph0 { + nvidia,pins = "ph0"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph1 { + nvidia,pins = "ph1"; + nvidia,function = "pwm1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph2 { + nvidia,pins = "ph2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph3 { + nvidia,pins = "ph3"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph4 { + nvidia,pins = "ph4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph5 { + nvidia,pins = "ph5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph6 { + nvidia,pins = "ph6"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph7 { + nvidia,pins = "ph7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi0 { + nvidia,pins = "pi0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi1 { + nvidia,pins = "pi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi2 { + nvidia,pins = "pi2"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi3 { + nvidia,pins = "pi3"; + nvidia,function = "spi4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi4 { + nvidia,pins = "pi4"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi5 { + nvidia,pins = "pi5"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi6 { + nvidia,pins = "pi6"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi7 { + nvidia,pins = "pi7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pj0 { + nvidia,pins = "pj0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pj2 { + nvidia,pins = "pj2"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart2_cts_n_pj5 { + nvidia,pins = "uart2_cts_n_pj5"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart2_rts_n_pj6 { + nvidia,pins = "uart2_rts_n_pj6"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pj7 { + nvidia,pins = "pj7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pk0 { + nvidia,pins = "pk0"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pk1 { + nvidia,pins = "pk1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pk2 { + nvidia,pins = "pk2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pk3 { + nvidia,pins = "pk3"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pk4 { + nvidia,pins = "pk4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + spdif_out_pk5 { + nvidia,pins = "spdif_out_pk5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + spdif_in_pk6 { + nvidia,pins = "spdif_in_pk6"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pk7 { + nvidia,pins = "pk7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap1_fs_pn0 { + nvidia,pins = "dap1_fs_pn0"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap1_din_pn1 { + nvidia,pins = "dap1_din_pn1"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap1_dout_pn2 { + nvidia,pins = "dap1_dout_pn2"; + nvidia,function = "i2s0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap1_sclk_pn3 { + nvidia,pins = "dap1_sclk_pn3"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + usb_vbus_en0_pn4 { + nvidia,pins = "usb_vbus_en0_pn4"; + nvidia,function = "usb"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + usb_vbus_en1_pn5 { + nvidia,pins = "usb_vbus_en1_pn5"; + nvidia,function = "usb"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + hdmi_int_pn7 { + nvidia,pins = "hdmi_int_pn7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,rcv-sel = ; + }; + ulpi_data7_po0 { + nvidia,pins = "ulpi_data7_po0"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data0_po1 { + nvidia,pins = "ulpi_data0_po1"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data1_po2 { + nvidia,pins = "ulpi_data1_po2"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data2_po3 { + nvidia,pins = "ulpi_data2_po3"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data3_po4 { + nvidia,pins = "ulpi_data3_po4"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data4_po5 { + nvidia,pins = "ulpi_data4_po5"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data5_po6 { + nvidia,pins = "ulpi_data5_po6"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data6_po7 { + nvidia,pins = "ulpi_data6_po7"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap3_fs_pp0 { + nvidia,pins = "dap3_fs_pp0"; + nvidia,function = "i2s2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap3_din_pp1 { + nvidia,pins = "dap3_din_pp1"; + nvidia,function = "i2s2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap3_dout_pp2 { + nvidia,pins = "dap3_dout_pp2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap3_sclk_pp3 { + nvidia,pins = "dap3_sclk_pp3"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap4_fs_pp4 { + nvidia,pins = "dap4_fs_pp4"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap4_din_pp5 { + nvidia,pins = "dap4_din_pp5"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap4_dout_pp6 { + nvidia,pins = "dap4_dout_pp6"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap4_sclk_pp7 { + nvidia,pins = "dap4_sclk_pp7"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col0_pq0 { + nvidia,pins = "kb_col0_pq0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col1_pq1 { + nvidia,pins = "kb_col1_pq1"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col2_pq2 { + nvidia,pins = "kb_col2_pq2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col3_pq3 { + nvidia,pins = "kb_col3_pq3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col4_pq4 { + nvidia,pins = "kb_col4_pq4"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col5_pq5 { + nvidia,pins = "kb_col5_pq5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col6_pq6 { + nvidia,pins = "kb_col6_pq6"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col7_pq7 { + nvidia,pins = "kb_col7_pq7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row0_pr0 { + nvidia,pins = "kb_row0_pr0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row1_pr1 { + nvidia,pins = "kb_row1_pr1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row2_pr2 { + nvidia,pins = "kb_row2_pr2"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row3_pr3 { + nvidia,pins = "kb_row3_pr3"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row4_pr4 { + nvidia,pins = "kb_row4_pr4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row5_pr5 { + nvidia,pins = "kb_row5_pr5"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row6_pr6 { + nvidia,pins = "kb_row6_pr6"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row7_pr7 { + nvidia,pins = "kb_row7_pr7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row8_ps0 { + nvidia,pins = "kb_row8_ps0"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row9_ps1 { + nvidia,pins = "kb_row9_ps1"; + nvidia,function = "uarta"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row10_ps2 { + nvidia,pins = "kb_row10_ps2"; + nvidia,function = "uarta"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row11_ps3 { + nvidia,pins = "kb_row11_ps3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row12_ps4 { + nvidia,pins = "kb_row12_ps4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row13_ps5 { + nvidia,pins = "kb_row13_ps5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row14_ps6 { + nvidia,pins = "kb_row14_ps6"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row15_ps7 { + nvidia,pins = "kb_row15_ps7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row16_pt0 { + nvidia,pins = "kb_row16_pt0"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row17_pt1 { + nvidia,pins = "kb_row17_pt1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gen2_i2c_scl_pt5 { + nvidia,pins = "gen2_i2c_scl_pt5"; + nvidia,function = "i2c2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + gen2_i2c_sda_pt6 { + nvidia,pins = "gen2_i2c_sda_pt6"; + nvidia,function = "i2c2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + sdmmc4_cmd_pt7 { + nvidia,pins = "sdmmc4_cmd_pt7"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu0 { + nvidia,pins = "pu0"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu1 { + nvidia,pins = "pu1"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu2 { + nvidia,pins = "pu2"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu3 { + nvidia,pins = "pu3"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu4 { + nvidia,pins = "pu4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu5 { + nvidia,pins = "pu5"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu6 { + nvidia,pins = "pu6"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pv0 { + nvidia,pins = "pv0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pv1 { + nvidia,pins = "pv1"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_cd_n_pv2 { + nvidia,pins = "sdmmc3_cd_n_pv2"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_wp_n_pv3 { + nvidia,pins = "sdmmc1_wp_n_pv3"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ddc_scl_pv4 { + nvidia,pins = "ddc_scl_pv4"; + nvidia,function = "i2c4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,rcv-sel = ; + }; + ddc_sda_pv5 { + nvidia,pins = "ddc_sda_pv5"; + nvidia,function = "i2c4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,rcv-sel = ; + }; + gpio_w2_aud_pw2 { + nvidia,pins = "gpio_w2_aud_pw2"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_w3_aud_pw3 { + nvidia,pins = "gpio_w3_aud_pw3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap_mclk1_pw4 { + nvidia,pins = "dap_mclk1_pw4"; + nvidia,function = "extperiph1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk2_out_pw5 { + nvidia,pins = "clk2_out_pw5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart3_txd_pw6 { + nvidia,pins = "uart3_txd_pw6"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart3_rxd_pw7 { + nvidia,pins = "uart3_rxd_pw7"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dvfs_pwm_px0 { + nvidia,pins = "dvfs_pwm_px0"; + nvidia,function = "cldvfs"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_x1_aud_px1 { + nvidia,pins = "gpio_x1_aud_px1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dvfs_clk_px2 { + nvidia,pins = "dvfs_clk_px2"; + nvidia,function = "cldvfs"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_x3_aud_px3 { + nvidia,pins = "gpio_x3_aud_px3"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_x4_aud_px4 { + nvidia,pins = "gpio_x4_aud_px4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_x5_aud_px5 { + nvidia,pins = "gpio_x5_aud_px5"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_x6_aud_px6 { + nvidia,pins = "gpio_x6_aud_px6"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_x7_aud_px7 { + nvidia,pins = "gpio_x7_aud_px7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_clk_py0 { + nvidia,pins = "ulpi_clk_py0"; + nvidia,function = "spi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_dir_py1 { + nvidia,pins = "ulpi_dir_py1"; + nvidia,function = "spi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_nxt_py2 { + nvidia,pins = "ulpi_nxt_py2"; + nvidia,function = "spi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_stp_py3 { + nvidia,pins = "ulpi_stp_py3"; + nvidia,function = "spi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_dat3_py4 { + nvidia,pins = "sdmmc1_dat3_py4"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_dat2_py5 { + nvidia,pins = "sdmmc1_dat2_py5"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_dat1_py6 { + nvidia,pins = "sdmmc1_dat1_py6"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_dat0_py7 { + nvidia,pins = "sdmmc1_dat0_py7"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_clk_pz0 { + nvidia,pins = "sdmmc1_clk_pz0"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_cmd_pz1 { + nvidia,pins = "sdmmc1_cmd_pz1"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pwr_i2c_scl_pz6 { + nvidia,pins = "pwr_i2c_scl_pz6"; + nvidia,function = "i2cpwr"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + pwr_i2c_sda_pz7 { + nvidia,pins = "pwr_i2c_sda_pz7"; + nvidia,function = "i2cpwr"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + sdmmc4_dat0_paa0 { + nvidia,pins = "sdmmc4_dat0_paa0"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat1_paa1 { + nvidia,pins = "sdmmc4_dat1_paa1"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat2_paa2 { + nvidia,pins = "sdmmc4_dat2_paa2"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat3_paa3 { + nvidia,pins = "sdmmc4_dat3_paa3"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat4_paa4 { + nvidia,pins = "sdmmc4_dat4_paa4"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat5_paa5 { + nvidia,pins = "sdmmc4_dat5_paa5"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat6_paa6 { + nvidia,pins = "sdmmc4_dat6_paa6"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat7_paa7 { + nvidia,pins = "sdmmc4_dat7_paa7"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb0 { + nvidia,pins = "pbb0"; + nvidia,function = "vgp6"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + cam_i2c_scl_pbb1 { + nvidia,pins = "cam_i2c_scl_pbb1"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + cam_i2c_sda_pbb2 { + nvidia,pins = "cam_i2c_sda_pbb2"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + pbb3 { + nvidia,pins = "pbb3"; + nvidia,function = "vgp3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb4 { + nvidia,pins = "pbb4"; + nvidia,function = "vgp4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb5 { + nvidia,pins = "pbb5"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb6 { + nvidia,pins = "pbb6"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb7 { + nvidia,pins = "pbb7"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + cam_mclk_pcc0 { + nvidia,pins = "cam_mclk_pcc0"; + nvidia,function = "vi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pcc1 { + nvidia,pins = "pcc1"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pcc2 { + nvidia,pins = "pcc2"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_clk_pcc4 { + nvidia,pins = "sdmmc4_clk_pcc4"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk2_req_pcc5 { + nvidia,pins = "clk2_req_pcc5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l0_rst_n_pdd1 { + nvidia,pins = "pex_l0_rst_n_pdd1"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l0_clkreq_n_pdd2 { + nvidia,pins = "pex_l0_clkreq_n_pdd2"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_wake_n_pdd3 { + nvidia,pins = "pex_wake_n_pdd3"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l1_rst_n_pdd5 { + nvidia,pins = "pex_l1_rst_n_pdd5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l1_clkreq_n_pdd6 { + nvidia,pins = "pex_l1_clkreq_n_pdd6"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk3_out_pee0 { + nvidia,pins = "clk3_out_pee0"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk3_req_pee1 { + nvidia,pins = "clk3_req_pee1"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap_mclk1_req_pee2 { + nvidia,pins = "dap_mclk1_req_pee2"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + hdmi_cec_pee3 { + nvidia,pins = "hdmi_cec_pee3"; + nvidia,function = "cec"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + sdmmc3_clk_lb_out_pee4 { + nvidia,pins = "sdmmc3_clk_lb_out_pee4"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_clk_lb_in_pee5 { + nvidia,pins = "sdmmc3_clk_lb_in_pee5"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dp_hpd_pff0 { + nvidia,pins = "dp_hpd_pff0"; + nvidia,function = "dp"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + usb_vbus_en2_pff1 { + nvidia,pins = "usb_vbus_en2_pff1"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + pff2 { + nvidia,pins = "pff2"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + core_pwr_req { + nvidia,pins = "core_pwr_req"; + nvidia,function = "pwron"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + cpu_pwr_req { + nvidia,pins = "cpu_pwr_req"; + nvidia,function = "cpu"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pwr_int_n { + nvidia,pins = "pwr_int_n"; + nvidia,function = "pmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + reset_out_n { + nvidia,pins = "reset_out_n"; + nvidia,function = "reset_out_n"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + owr { + nvidia,pins = "owr"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,rcv-sel = ; + }; + clk_32k_in { + nvidia,pins = "clk_32k_in"; + nvidia,function = "clk"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + jtag_rtck { + nvidia,pins = "jtag_rtck"; + nvidia,function = "rtck"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + }; }; }; - -#include "cros-ec-keyboard.dtsi" diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze-emc.dtsi b/arch/arm/boot/dts/tegra124-nyan-blaze-emc.dtsi new file mode 100644 index 000000000000..9ecd108f56cf --- /dev/null +++ b/arch/arm/boot/dts/tegra124-nyan-blaze-emc.dtsi @@ -0,0 +1,2049 @@ +/ { + clock@0,60006000 { + emc-timings-1 { + nvidia,ram-code = <1>; + + timing-12750000 { + clock-frequency = <12750000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-20400000 { + clock-frequency = <20400000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-40800000 { + clock-frequency = <40800000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-68000000 { + clock-frequency = <68000000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-102000000 { + clock-frequency = <102000000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-204000000 { + clock-frequency = <204000000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-300000000 { + clock-frequency = <300000000>; + nvidia,parent-clock-frequency = <600000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_C>; + clock-names = "emc-parent"; + }; + timing-396000000 { + clock-frequency = <396000000>; + nvidia,parent-clock-frequency = <792000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_M>; + clock-names = "emc-parent"; + }; + /* TODO: Add 528MHz frequency */ + timing-600000000 { + clock-frequency = <600000000>; + nvidia,parent-clock-frequency = <600000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>; + clock-names = "emc-parent"; + }; + timing-792000000 { + clock-frequency = <792000000>; + nvidia,parent-clock-frequency = <792000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>; + clock-names = "emc-parent"; + }; + }; + }; + + emc@0,7001b000 { + emc-timings-1 { + nvidia,ram-code = <1>; + + timing-12750000 { + clock-frequency = <12750000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000c000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000a + 0x00000003 + 0x0000000b + 0x00000000 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x00000060 + 0x00000000 + 0x00000018 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000007 + 0x0000000f + 0x00000005 + 0x00000005 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000000 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000064 + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x0000c000 + 0x00000000 + 0x00000000 + 0x0000c000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000505 + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000007 + 0x00000000 + 0x00000042 + 0x000c000c + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x800001c5 + 0x0000000a + >; + }; + + timing-20400000 { + clock-frequency = <20400000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000c000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000000 + 0x00000005 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000a + 0x00000003 + 0x0000000b + 0x00000000 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x0000009a + 0x00000000 + 0x00000026 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000007 + 0x0000000f + 0x00000006 + 0x00000006 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000000 + 0x00000000 + 0x00000005 + 0x00000005 + 0x000000a0 + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x0000c000 + 0x00000000 + 0x00000000 + 0x0000c000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000505 + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x0000000b + 0x00000000 + 0x00000042 + 0x000c000c + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x8000023a + 0x0000000a + >; + }; + + timing-40800000 { + clock-frequency = <40800000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000c000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000001 + 0x0000000a + 0x00000000 + 0x00000001 + 0x00000000 + 0x00000004 + 0x0000000a + 0x00000003 + 0x0000000b + 0x00000000 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x00000134 + 0x00000000 + 0x0000004d + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000008 + 0x0000000f + 0x0000000c + 0x0000000c + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000000 + 0x00000000 + 0x00000005 + 0x00000005 + 0x0000013f + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x0000c000 + 0x00000000 + 0x00000000 + 0x0000c000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000505 + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000015 + 0x00000000 + 0x00000042 + 0x000c000c + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x80000370 + 0x0000000a + >; + }; + + timing-68000000 { + clock-frequency = <68000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000c000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000003 + 0x00000011 + 0x00000000 + 0x00000002 + 0x00000000 + 0x00000004 + 0x0000000a + 0x00000003 + 0x0000000b + 0x00000000 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x00000202 + 0x00000000 + 0x00000080 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x0000000f + 0x0000000f + 0x00000013 + 0x00000013 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000001 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000213 + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x0000c000 + 0x00000000 + 0x00000000 + 0x0000c000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000505 + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000022 + 0x00000000 + 0x00000042 + 0x000c000c + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x8000050e + 0x0000000a + >; + }; + + timing-102000000 { + clock-frequency = <102000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x000008c5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000c000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00000000>; + + nvidia,emc-configuration = < + 0x00000004 + 0x0000001a + 0x00000000 + 0x00000003 + 0x00000001 + 0x00000004 + 0x0000000a + 0x00000003 + 0x0000000b + 0x00000001 + 0x00000001 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x0000000c + 0x0000000d + 0x0000000f + 0x00000304 + 0x00000000 + 0x000000c1 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000018 + 0x0000000f + 0x0000001c + 0x0000001c + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000003 + 0x00000000 + 0x00000005 + 0x00000005 + 0x0000031c + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x0000c000 + 0x00000000 + 0x00000000 + 0x0000c000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x000fc000 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x0000fc00 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000505 + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000033 + 0x00000000 + 0x00000042 + 0x000c000c + 0x00000000 + 0x00000003 + 0x0000f2f3 + 0x80000713 + 0x0000000a + >; + }; + + timing-204000000 { + clock-frequency = <204000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000008>; + nvidia,emc-cfg = <0x73240000>; + nvidia,emc-cfg-2 = <0x0000088d>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100003>; + nvidia,emc-mode-2 = <0x80200008>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80001221>; + nvidia,emc-mrs-wait-cnt = <0x000c000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040008>; + nvidia,emc-xm2dqspadctrl2 = <0x0130b118>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x00000009 + 0x00000035 + 0x00000000 + 0x00000007 + 0x00000002 + 0x00000005 + 0x0000000a + 0x00000003 + 0x0000000b + 0x00000002 + 0x00000002 + 0x00000003 + 0x00000003 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000006 + 0x00000002 + 0x00000000 + 0x00000004 + 0x00000006 + 0x00010000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000003 + 0x0000000d + 0x0000000f + 0x00000011 + 0x00000607 + 0x00000000 + 0x00000181 + 0x00000002 + 0x00000002 + 0x00000001 + 0x00000000 + 0x00000032 + 0x0000000f + 0x00000038 + 0x00000038 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000007 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000638 + 0x00000000 + 0x00000000 + 0x00000000 + 0x106aa298 + 0x002c00a0 + 0x00008000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00064000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x0000c000 + 0x00000000 + 0x00000000 + 0x0000c000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00090000 + 0x00090000 + 0x00090000 + 0x00090000 + 0x00009000 + 0x00009000 + 0x00009000 + 0x00009000 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000505 + 0x81f1f108 + 0x07070004 + 0x0000003f + 0x016eeeee + 0x51451400 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000066 + 0x00000000 + 0x00000100 + 0x000c000c + 0x00000000 + 0x00000003 + 0x0000d2b3 + 0x80000d22 + 0x0000000a + >; + }; + + timing-300000000 { + clock-frequency = <300000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73340000>; + nvidia,emc-cfg-2 = <0x000008d5>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200000>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000321>; + nvidia,emc-mrs-wait-cnt = <0x0174000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040128>; + nvidia,emc-xm2dqspadctrl2 = <0x01231339>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x0000000d + 0x0000004c + 0x00000000 + 0x00000009 + 0x00000003 + 0x00000004 + 0x00000008 + 0x00000002 + 0x00000009 + 0x00000003 + 0x00000003 + 0x00000002 + 0x00000002 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000005 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000007 + 0x00020000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000001 + 0x0000000e + 0x00000010 + 0x00000012 + 0x000008e4 + 0x00000000 + 0x00000239 + 0x00000001 + 0x00000008 + 0x00000001 + 0x00000000 + 0x0000004a + 0x0000000e + 0x00000051 + 0x00000200 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000009 + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000924 + 0x00000000 + 0x00000000 + 0x00000000 + 0x104ab098 + 0x002c00a0 + 0x00008000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00090000 + 0x00090000 + 0x00000000 + 0x00090000 + 0x00090000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00060000 + 0x00060000 + 0x00060000 + 0x00060000 + 0x00006000 + 0x00006000 + 0x00006000 + 0x00006000 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000202 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x51451420 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x00000096 + 0x00000000 + 0x00000100 + 0x0174000c + 0x00000000 + 0x00000003 + 0x000052a3 + 0x800012d7 + 0x00000009 + >; + }; + + timing-396000000 { + clock-frequency = <396000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73340000>; + nvidia,emc-cfg-2 = <0x00000895>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200000>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000521>; + nvidia,emc-mrs-wait-cnt = <0x015b000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040008>; + nvidia,emc-xm2dqspadctrl2 = <0x01231339>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x00000012 + 0x00000065 + 0x00000000 + 0x0000000c + 0x00000004 + 0x00000005 + 0x00000008 + 0x00000002 + 0x0000000a + 0x00000004 + 0x00000004 + 0x00000002 + 0x00000002 + 0x00000000 + 0x00000003 + 0x00000003 + 0x00000005 + 0x00000002 + 0x00000000 + 0x00000001 + 0x00000008 + 0x00020000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x0000000f + 0x00000010 + 0x00000012 + 0x00000bd1 + 0x00000000 + 0x000002f4 + 0x00000001 + 0x00000008 + 0x00000001 + 0x00000000 + 0x00000063 + 0x0000000f + 0x0000006b + 0x00000200 + 0x00000004 + 0x00000005 + 0x00000004 + 0x0000000d + 0x00000000 + 0x00000005 + 0x00000005 + 0x00000c11 + 0x00000000 + 0x00000000 + 0x00000000 + 0x104ab098 + 0x002c00a0 + 0x00008000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00030000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00068000 + 0x00068000 + 0x00000000 + 0x00068000 + 0x00068000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00058000 + 0x00058000 + 0x00058000 + 0x00058000 + 0x00005800 + 0x00005800 + 0x00005800 + 0x00005800 + 0x10000280 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc081 + 0x00000202 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x51451420 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0000003f + 0x000000c6 + 0x00000000 + 0x00000100 + 0x015b000c + 0x00000000 + 0x00000003 + 0x000052a3 + 0x8000188b + 0x00000009 + >; + }; + + timing-600000000 { + clock-frequency = <600000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73300000>; + nvidia,emc-cfg-2 = <0x0000089d>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200010>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000b61>; + nvidia,emc-mrs-wait-cnt = <0x0128000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040008>; + nvidia,emc-xm2dqspadctrl2 = <0x0121113d>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x0000001c + 0x0000009a + 0x00000000 + 0x00000013 + 0x00000007 + 0x00000007 + 0x0000000b + 0x00000003 + 0x00000010 + 0x00000007 + 0x00000007 + 0x00000002 + 0x00000002 + 0x00000000 + 0x00000005 + 0x00000005 + 0x0000000a + 0x00000002 + 0x00000000 + 0x00000003 + 0x0000000b + 0x00070000 + 0x00000003 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000002 + 0x00000012 + 0x00000016 + 0x00000018 + 0x00001208 + 0x00000000 + 0x00000482 + 0x00000002 + 0x0000000d + 0x00000001 + 0x00000000 + 0x00000096 + 0x00000015 + 0x000000a2 + 0x00000200 + 0x00000004 + 0x00000005 + 0x00000004 + 0x00000015 + 0x00000000 + 0x00000006 + 0x00000006 + 0x00001248 + 0x00000000 + 0x00000000 + 0x00000000 + 0x104ab098 + 0xe00e00b1 + 0x00008000 + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x0000000a + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00040000 + 0x00040000 + 0x00000000 + 0x00040000 + 0x00040000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000004 + 0x00000004 + 0x00000001 + 0x00000005 + 0x00000007 + 0x00000004 + 0x00000006 + 0x00000007 + 0x00000004 + 0x00000004 + 0x00000001 + 0x00000005 + 0x00000007 + 0x00000004 + 0x00000006 + 0x00000007 + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x100002a0 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc085 + 0x00000202 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x51451420 + 0x00514514 + 0x00514514 + 0x51451400 + 0x0606003f + 0x00000000 + 0x00000000 + 0x00000100 + 0x0128000c + 0x00000000 + 0x00000003 + 0x000040a0 + 0x800024a9 + 0x0000000e + >; + }; + + timing-792000000 { + clock-frequency = <792000000>; + + nvidia,emc-auto-cal-config = <0xa1430000>; + nvidia,emc-auto-cal-config2 = <0x00000000>; + nvidia,emc-auto-cal-config3 = <0x00000000>; + nvidia,emc-auto-cal-interval = <0x001fffff>; + nvidia,emc-bgbias-ctl0 = <0x00000000>; + nvidia,emc-cfg = <0x73300000>; + nvidia,emc-cfg-2 = <0x0000089d>; + nvidia,emc-ctt-term-ctrl = <0x00000802>; + nvidia,emc-mode-1 = <0x80100002>; + nvidia,emc-mode-2 = <0x80200018>; + nvidia,emc-mode-4 = <0x00000000>; + nvidia,emc-mode-reset = <0x80000d71>; + nvidia,emc-mrs-wait-cnt = <0x00f8000c>; + nvidia,emc-sel-dpd-ctrl = <0x00040000>; + nvidia,emc-xm2dqspadctrl2 = <0x0120113d>; + nvidia,emc-zcal-cnt-long = <0x00000042>; + nvidia,emc-zcal-interval = <0x00020000>; + + nvidia,emc-configuration = < + 0x00000025 + 0x000000cc + 0x00000000 + 0x0000001a + 0x00000009 + 0x00000008 + 0x0000000d + 0x00000004 + 0x00000013 + 0x00000009 + 0x00000009 + 0x00000003 + 0x00000002 + 0x00000000 + 0x00000006 + 0x00000006 + 0x0000000b + 0x00000002 + 0x00000000 + 0x00000002 + 0x0000000d + 0x00080000 + 0x00000004 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000001 + 0x00000014 + 0x00000018 + 0x0000001a + 0x000017e2 + 0x00000000 + 0x000005f8 + 0x00000003 + 0x00000011 + 0x00000001 + 0x00000000 + 0x000000c6 + 0x00000018 + 0x000000d6 + 0x00000200 + 0x00000005 + 0x00000006 + 0x00000005 + 0x0000001d + 0x00000000 + 0x00000008 + 0x00000008 + 0x00001822 + 0x00000000 + 0x00000000 + 0x00000000 + 0x104ab098 + 0xe00700b1 + 0x00008000 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000008 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x0002c000 + 0x0002c000 + 0x00000000 + 0x0002c000 + 0x0002c000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000000 + 0x00000008 + 0x00000008 + 0x00000005 + 0x00000008 + 0x0000000a + 0x00000008 + 0x0000000a + 0x0000000a + 0x00000008 + 0x00000008 + 0x00000005 + 0x00000008 + 0x0000000a + 0x00000008 + 0x0000000a + 0x0000000a + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x0000000e + 0x100002a0 + 0x00000000 + 0x00111111 + 0x00000000 + 0x00000000 + 0x77ffc085 + 0x00000202 + 0x81f1f108 + 0x07070004 + 0x00000000 + 0x016eeeee + 0x61861820 + 0x00492492 + 0x00492492 + 0x61861800 + 0x0606003f + 0x00000000 + 0x00000000 + 0x00000100 + 0x00f8000c + 0x00000000 + 0x00000004 + 0x00004080 + 0x80003012 + 0x0000000f + >; + }; + + }; + }; + + memory-controller@0,70019000 { + emc-timings-1 { + nvidia,ram-code = <1>; + + + timing-12750000 { + clock-frequency = <12750000>; + + nvidia,emem-configuration = < + 0x40040001 + 0x8000000a + 0x00000001 + 0x00000001 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0402 + 0x77e30303 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-20400000 { + clock-frequency = <20400000>; + + nvidia,emem-configuration = < + 0x40020001 + 0x80000012 + 0x00000001 + 0x00000001 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0402 + 0x76230303 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-40800000 { + clock-frequency = <40800000>; + + nvidia,emem-configuration = < + 0xa0000001 + 0x80000017 + 0x00000001 + 0x00000001 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0402 + 0x74a30303 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-68000000 { + clock-frequency = <68000000>; + + nvidia,emem-configuration = < + 0x00000001 + 0x8000001e + 0x00000001 + 0x00000001 + 0x00000002 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0402 + 0x74230403 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-102000000 { + clock-frequency = <102000000>; + + nvidia,emem-configuration = < + 0x08000001 + 0x80000026 + 0x00000001 + 0x00000001 + 0x00000003 + 0x00000000 + 0x00000002 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000003 + 0x00000006 + 0x06030203 + 0x000a0403 + 0x73c30504 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-204000000 { + clock-frequency = <204000000>; + + nvidia,emem-configuration = < + 0x01000003 + 0x80000040 + 0x00000001 + 0x00000001 + 0x00000005 + 0x00000002 + 0x00000004 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000003 + 0x00000002 + 0x00000004 + 0x00000006 + 0x06040203 + 0x000a0405 + 0x73840a06 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-300000000 { + clock-frequency = <300000000>; + + nvidia,emem-configuration = < + 0x08000004 + 0x80000040 + 0x00000001 + 0x00000002 + 0x00000007 + 0x00000004 + 0x00000005 + 0x00000001 + 0x00000002 + 0x00000007 + 0x00000002 + 0x00000002 + 0x00000004 + 0x00000006 + 0x06040202 + 0x000b0607 + 0x77450e08 + 0x70000f03 + 0x001f0000 + >; + }; + + timing-396000000 { + clock-frequency = <396000000>; + + nvidia,emem-configuration = < + 0x0f000005 + 0x80000040 + 0x00000001 + 0x00000002 + 0x00000009 + 0x00000005 + 0x00000007 + 0x00000001 + 0x00000002 + 0x00000008 + 0x00000002 + 0x00000002 + 0x00000004 + 0x00000006 + 0x06040202 + 0x000d0709 + 0x7586120a + 0x70000f03 + 0x001f0000 + >; + }; + + timing-528000000 { + clock-frequency = <528000000>; + + nvidia,emem-configuration = < + 0x0f000007 + 0x80000040 + 0x00000002 + 0x00000003 + 0x0000000d + 0x00000008 + 0x0000000a + 0x00000001 + 0x00000002 + 0x00000009 + 0x00000002 + 0x00000002 + 0x00000005 + 0x00000006 + 0x06050202 + 0x0010090d + 0x7428180e + 0x70000f03 + 0x001f0000 + >; + }; + + timing-600000000 { + clock-frequency = <600000000>; + + nvidia,emem-configuration = < + 0x00000009 + 0x80000040 + 0x00000003 + 0x00000004 + 0x0000000e + 0x00000009 + 0x0000000b + 0x00000001 + 0x00000003 + 0x0000000b + 0x00000002 + 0x00000002 + 0x00000005 + 0x00000007 + 0x07050202 + 0x00130b0e + 0x73a91b0f + 0x70000f03 + 0x001f0000 + >; + }; + + timing-792000000 { + clock-frequency = <792000000>; + + nvidia,emem-configuration = < + 0x0e00000b + 0x80000040 + 0x00000004 + 0x00000005 + 0x00000013 + 0x0000000c + 0x0000000f + 0x00000002 + 0x00000003 + 0x0000000c + 0x00000002 + 0x00000002 + 0x00000006 + 0x00000008 + 0x08060202 + 0x00160d13 + 0x734c2414 + 0x70000f02 + 0x001f0000 + >; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts b/arch/arm/boot/dts/tegra124-nyan-blaze.dts new file mode 100644 index 000000000000..0d30c514ffad --- /dev/null +++ b/arch/arm/boot/dts/tegra124-nyan-blaze.dts @@ -0,0 +1,1334 @@ +/dts-v1/; + +#include "tegra124-nyan.dtsi" + +#include "tegra124-nyan-blaze-emc.dtsi" + +/ { + model = "HP Chromebook 14"; + compatible = "google,nyan-blaze", "google,nyan", "nvidia,tegra124"; + + panel: panel { + compatible = "samsung,ltn140at29-301"; + + backlight = <&backlight>; + ddc-i2c-bus = <&dpaux>; + }; + + sound { + compatible = "nvidia,tegra-audio-max98090-nyan-blaze", + "nvidia,tegra-audio-max98090-nyan", + "nvidia,tegra-audio-max98090"; + nvidia,model = "GoogleNyanBlaze"; + }; + + pinmux@0,70000868 { + pinctrl-names = "default"; + pinctrl-0 = <&pinmux_default>; + + pinmux_default: common { + clk_32k_out_pa0 { + nvidia,pins = "clk_32k_out_pa0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart3_cts_n_pa1 { + nvidia,pins = "uart3_cts_n_pa1"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap2_fs_pa2 { + nvidia,pins = "dap2_fs_pa2"; + nvidia,function = "i2s1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap2_sclk_pa3 { + nvidia,pins = "dap2_sclk_pa3"; + nvidia,function = "i2s1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap2_din_pa4 { + nvidia,pins = "dap2_din_pa4"; + nvidia,function = "i2s1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap2_dout_pa5 { + nvidia,pins = "dap2_dout_pa5"; + nvidia,function = "i2s1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_clk_pa6 { + nvidia,pins = "sdmmc3_clk_pa6"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_cmd_pa7 { + nvidia,pins = "sdmmc3_cmd_pa7"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pb0 { + nvidia,pins = "pb0"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pb1 { + nvidia,pins = "pb1"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat3_pb4 { + nvidia,pins = "sdmmc3_dat3_pb4"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat2_pb5 { + nvidia,pins = "sdmmc3_dat2_pb5"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat1_pb6 { + nvidia,pins = "sdmmc3_dat1_pb6"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat0_pb7 { + nvidia,pins = "sdmmc3_dat0_pb7"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart3_rts_n_pc0 { + nvidia,pins = "uart3_rts_n_pc0"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart2_txd_pc2 { + nvidia,pins = "uart2_txd_pc2"; + nvidia,function = "irda"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart2_rxd_pc3 { + nvidia,pins = "uart2_rxd_pc3"; + nvidia,function = "irda"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gen1_i2c_scl_pc4 { + nvidia,pins = "gen1_i2c_scl_pc4"; + nvidia,function = "i2c1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + gen1_i2c_sda_pc5 { + nvidia,pins = "gen1_i2c_sda_pc5"; + nvidia,function = "i2c1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + pc7 { + nvidia,pins = "pc7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg0 { + nvidia,pins = "pg0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg1 { + nvidia,pins = "pg1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg2 { + nvidia,pins = "pg2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg3 { + nvidia,pins = "pg3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg4 { + nvidia,pins = "pg4"; + nvidia,function = "spi4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg5 { + nvidia,pins = "pg5"; + nvidia,function = "spi4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg6 { + nvidia,pins = "pg6"; + nvidia,function = "spi4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pg7 { + nvidia,pins = "pg7"; + nvidia,function = "spi4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph0 { + nvidia,pins = "ph0"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph1 { + nvidia,pins = "ph1"; + nvidia,function = "pwm1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph2 { + nvidia,pins = "ph2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph3 { + nvidia,pins = "ph3"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph4 { + nvidia,pins = "ph4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph5 { + nvidia,pins = "ph5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph6 { + nvidia,pins = "ph6"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ph7 { + nvidia,pins = "ph7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi0 { + nvidia,pins = "pi0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi1 { + nvidia,pins = "pi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi2 { + nvidia,pins = "pi2"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi3 { + nvidia,pins = "pi3"; + nvidia,function = "spi4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi4 { + nvidia,pins = "pi4"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi5 { + nvidia,pins = "pi5"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi6 { + nvidia,pins = "pi6"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pi7 { + nvidia,pins = "pi7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pj0 { + nvidia,pins = "pj0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pj2 { + nvidia,pins = "pj2"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart2_cts_n_pj5 { + nvidia,pins = "uart2_cts_n_pj5"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart2_rts_n_pj6 { + nvidia,pins = "uart2_rts_n_pj6"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pj7 { + nvidia,pins = "pj7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pk0 { + nvidia,pins = "pk0"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pk1 { + nvidia,pins = "pk1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pk2 { + nvidia,pins = "pk2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pk3 { + nvidia,pins = "pk3"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pk4 { + nvidia,pins = "pk4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + spdif_out_pk5 { + nvidia,pins = "spdif_out_pk5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + spdif_in_pk6 { + nvidia,pins = "spdif_in_pk6"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pk7 { + nvidia,pins = "pk7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap1_fs_pn0 { + nvidia,pins = "dap1_fs_pn0"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap1_din_pn1 { + nvidia,pins = "dap1_din_pn1"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap1_dout_pn2 { + nvidia,pins = "dap1_dout_pn2"; + nvidia,function = "i2s0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap1_sclk_pn3 { + nvidia,pins = "dap1_sclk_pn3"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + usb_vbus_en0_pn4 { + nvidia,pins = "usb_vbus_en0_pn4"; + nvidia,function = "usb"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + usb_vbus_en1_pn5 { + nvidia,pins = "usb_vbus_en1_pn5"; + nvidia,function = "usb"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + hdmi_int_pn7 { + nvidia,pins = "hdmi_int_pn7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,rcv-sel = ; + }; + ulpi_data7_po0 { + nvidia,pins = "ulpi_data7_po0"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data0_po1 { + nvidia,pins = "ulpi_data0_po1"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data1_po2 { + nvidia,pins = "ulpi_data1_po2"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data2_po3 { + nvidia,pins = "ulpi_data2_po3"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data3_po4 { + nvidia,pins = "ulpi_data3_po4"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data4_po5 { + nvidia,pins = "ulpi_data4_po5"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data5_po6 { + nvidia,pins = "ulpi_data5_po6"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data6_po7 { + nvidia,pins = "ulpi_data6_po7"; + nvidia,function = "ulpi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap3_fs_pp0 { + nvidia,pins = "dap3_fs_pp0"; + nvidia,function = "i2s2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap3_din_pp1 { + nvidia,pins = "dap3_din_pp1"; + nvidia,function = "i2s2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap3_dout_pp2 { + nvidia,pins = "dap3_dout_pp2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap3_sclk_pp3 { + nvidia,pins = "dap3_sclk_pp3"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap4_fs_pp4 { + nvidia,pins = "dap4_fs_pp4"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap4_din_pp5 { + nvidia,pins = "dap4_din_pp5"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap4_dout_pp6 { + nvidia,pins = "dap4_dout_pp6"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap4_sclk_pp7 { + nvidia,pins = "dap4_sclk_pp7"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col0_pq0 { + nvidia,pins = "kb_col0_pq0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col1_pq1 { + nvidia,pins = "kb_col1_pq1"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col2_pq2 { + nvidia,pins = "kb_col2_pq2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col3_pq3 { + nvidia,pins = "kb_col3_pq3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col4_pq4 { + nvidia,pins = "kb_col4_pq4"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col5_pq5 { + nvidia,pins = "kb_col5_pq5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col6_pq6 { + nvidia,pins = "kb_col6_pq6"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col7_pq7 { + nvidia,pins = "kb_col7_pq7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row0_pr0 { + nvidia,pins = "kb_row0_pr0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row1_pr1 { + nvidia,pins = "kb_row1_pr1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row2_pr2 { + nvidia,pins = "kb_row2_pr2"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row3_pr3 { + nvidia,pins = "kb_row3_pr3"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row4_pr4 { + nvidia,pins = "kb_row4_pr4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row5_pr5 { + nvidia,pins = "kb_row5_pr5"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row6_pr6 { + nvidia,pins = "kb_row6_pr6"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row7_pr7 { + nvidia,pins = "kb_row7_pr7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row8_ps0 { + nvidia,pins = "kb_row8_ps0"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row9_ps1 { + nvidia,pins = "kb_row9_ps1"; + nvidia,function = "uarta"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row10_ps2 { + nvidia,pins = "kb_row10_ps2"; + nvidia,function = "uarta"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row11_ps3 { + nvidia,pins = "kb_row11_ps3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row12_ps4 { + nvidia,pins = "kb_row12_ps4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row13_ps5 { + nvidia,pins = "kb_row13_ps5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row14_ps6 { + nvidia,pins = "kb_row14_ps6"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row15_ps7 { + nvidia,pins = "kb_row15_ps7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row16_pt0 { + nvidia,pins = "kb_row16_pt0"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row17_pt1 { + nvidia,pins = "kb_row17_pt1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gen2_i2c_scl_pt5 { + nvidia,pins = "gen2_i2c_scl_pt5"; + nvidia,function = "i2c2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + gen2_i2c_sda_pt6 { + nvidia,pins = "gen2_i2c_sda_pt6"; + nvidia,function = "i2c2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + sdmmc4_cmd_pt7 { + nvidia,pins = "sdmmc4_cmd_pt7"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu0 { + nvidia,pins = "pu0"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu1 { + nvidia,pins = "pu1"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu2 { + nvidia,pins = "pu2"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu3 { + nvidia,pins = "pu3"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu4 { + nvidia,pins = "pu4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu5 { + nvidia,pins = "pu5"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu6 { + nvidia,pins = "pu6"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pv0 { + nvidia,pins = "pv0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pv1 { + nvidia,pins = "pv1"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_cd_n_pv2 { + nvidia,pins = "sdmmc3_cd_n_pv2"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_wp_n_pv3 { + nvidia,pins = "sdmmc1_wp_n_pv3"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ddc_scl_pv4 { + nvidia,pins = "ddc_scl_pv4"; + nvidia,function = "i2c4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,rcv-sel = ; + }; + ddc_sda_pv5 { + nvidia,pins = "ddc_sda_pv5"; + nvidia,function = "i2c4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,rcv-sel = ; + }; + gpio_w2_aud_pw2 { + nvidia,pins = "gpio_w2_aud_pw2"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_w3_aud_pw3 { + nvidia,pins = "gpio_w3_aud_pw3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap_mclk1_pw4 { + nvidia,pins = "dap_mclk1_pw4"; + nvidia,function = "extperiph1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk2_out_pw5 { + nvidia,pins = "clk2_out_pw5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart3_txd_pw6 { + nvidia,pins = "uart3_txd_pw6"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart3_rxd_pw7 { + nvidia,pins = "uart3_rxd_pw7"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dvfs_pwm_px0 { + nvidia,pins = "dvfs_pwm_px0"; + nvidia,function = "cldvfs"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_x1_aud_px1 { + nvidia,pins = "gpio_x1_aud_px1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dvfs_clk_px2 { + nvidia,pins = "dvfs_clk_px2"; + nvidia,function = "cldvfs"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_x3_aud_px3 { + nvidia,pins = "gpio_x3_aud_px3"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_x4_aud_px4 { + nvidia,pins = "gpio_x4_aud_px4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_x5_aud_px5 { + nvidia,pins = "gpio_x5_aud_px5"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_x6_aud_px6 { + nvidia,pins = "gpio_x6_aud_px6"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gpio_x7_aud_px7 { + nvidia,pins = "gpio_x7_aud_px7"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_clk_py0 { + nvidia,pins = "ulpi_clk_py0"; + nvidia,function = "spi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_dir_py1 { + nvidia,pins = "ulpi_dir_py1"; + nvidia,function = "spi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_nxt_py2 { + nvidia,pins = "ulpi_nxt_py2"; + nvidia,function = "spi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_stp_py3 { + nvidia,pins = "ulpi_stp_py3"; + nvidia,function = "spi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_dat3_py4 { + nvidia,pins = "sdmmc1_dat3_py4"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_dat2_py5 { + nvidia,pins = "sdmmc1_dat2_py5"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_dat1_py6 { + nvidia,pins = "sdmmc1_dat1_py6"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_dat0_py7 { + nvidia,pins = "sdmmc1_dat0_py7"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_clk_pz0 { + nvidia,pins = "sdmmc1_clk_pz0"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_cmd_pz1 { + nvidia,pins = "sdmmc1_cmd_pz1"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pwr_i2c_scl_pz6 { + nvidia,pins = "pwr_i2c_scl_pz6"; + nvidia,function = "i2cpwr"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + pwr_i2c_sda_pz7 { + nvidia,pins = "pwr_i2c_sda_pz7"; + nvidia,function = "i2cpwr"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + sdmmc4_dat0_paa0 { + nvidia,pins = "sdmmc4_dat0_paa0"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat1_paa1 { + nvidia,pins = "sdmmc4_dat1_paa1"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat2_paa2 { + nvidia,pins = "sdmmc4_dat2_paa2"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat3_paa3 { + nvidia,pins = "sdmmc4_dat3_paa3"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat4_paa4 { + nvidia,pins = "sdmmc4_dat4_paa4"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat5_paa5 { + nvidia,pins = "sdmmc4_dat5_paa5"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat6_paa6 { + nvidia,pins = "sdmmc4_dat6_paa6"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat7_paa7 { + nvidia,pins = "sdmmc4_dat7_paa7"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb0 { + nvidia,pins = "pbb0"; + nvidia,function = "vgp6"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + cam_i2c_scl_pbb1 { + nvidia,pins = "cam_i2c_scl_pbb1"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + cam_i2c_sda_pbb2 { + nvidia,pins = "cam_i2c_sda_pbb2"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + pbb3 { + nvidia,pins = "pbb3"; + nvidia,function = "vgp3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb4 { + nvidia,pins = "pbb4"; + nvidia,function = "vgp4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb5 { + nvidia,pins = "pbb5"; + nvidia,function = "rsvd3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb6 { + nvidia,pins = "pbb6"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb7 { + nvidia,pins = "pbb7"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + cam_mclk_pcc0 { + nvidia,pins = "cam_mclk_pcc0"; + nvidia,function = "vi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pcc1 { + nvidia,pins = "pcc1"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pcc2 { + nvidia,pins = "pcc2"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_clk_pcc4 { + nvidia,pins = "sdmmc4_clk_pcc4"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk2_req_pcc5 { + nvidia,pins = "clk2_req_pcc5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l0_rst_n_pdd1 { + nvidia,pins = "pex_l0_rst_n_pdd1"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l0_clkreq_n_pdd2 { + nvidia,pins = "pex_l0_clkreq_n_pdd2"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_wake_n_pdd3 { + nvidia,pins = "pex_wake_n_pdd3"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l1_rst_n_pdd5 { + nvidia,pins = "pex_l1_rst_n_pdd5"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l1_clkreq_n_pdd6 { + nvidia,pins = "pex_l1_clkreq_n_pdd6"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk3_out_pee0 { + nvidia,pins = "clk3_out_pee0"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk3_req_pee1 { + nvidia,pins = "clk3_req_pee1"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap_mclk1_req_pee2 { + nvidia,pins = "dap_mclk1_req_pee2"; + nvidia,function = "rsvd4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + hdmi_cec_pee3 { + nvidia,pins = "hdmi_cec_pee3"; + nvidia,function = "cec"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + sdmmc3_clk_lb_out_pee4 { + nvidia,pins = "sdmmc3_clk_lb_out_pee4"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_clk_lb_in_pee5 { + nvidia,pins = "sdmmc3_clk_lb_in_pee5"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dp_hpd_pff0 { + nvidia,pins = "dp_hpd_pff0"; + nvidia,function = "dp"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + usb_vbus_en2_pff1 { + nvidia,pins = "usb_vbus_en2_pff1"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + pff2 { + nvidia,pins = "pff2"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + core_pwr_req { + nvidia,pins = "core_pwr_req"; + nvidia,function = "pwron"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + cpu_pwr_req { + nvidia,pins = "cpu_pwr_req"; + nvidia,function = "cpu"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pwr_int_n { + nvidia,pins = "pwr_int_n"; + nvidia,function = "pmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + reset_out_n { + nvidia,pins = "reset_out_n"; + nvidia,function = "reset_out_n"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + owr { + nvidia,pins = "owr"; + nvidia,function = "rsvd2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,rcv-sel = ; + }; + clk_32k_in { + nvidia,pins = "clk_32k_in"; + nvidia,function = "clk"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + jtag_rtck { + nvidia,pins = "jtag_rtck"; + nvidia,function = "rtck"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/tegra124-nyan.dtsi b/arch/arm/boot/dts/tegra124-nyan.dtsi new file mode 100644 index 000000000000..a9aec23e06f2 --- /dev/null +++ b/arch/arm/boot/dts/tegra124-nyan.dtsi @@ -0,0 +1,695 @@ +#include +#include "tegra124.dtsi" + +/ { + aliases { + rtc0 = "/i2c@0,7000d000/pmic@40"; + rtc1 = "/rtc@0,7000e000"; + serial0 = &uarta; + }; + + memory { + reg = <0x0 0x80000000 0x0 0x80000000>; + }; + + host1x@0,50000000 { + hdmi@0,54280000 { + status = "okay"; + + vdd-supply = <&vdd_3v3_hdmi>; + pll-supply = <&vdd_hdmi_pll>; + hdmi-supply = <&vdd_5v0_hdmi>; + + nvidia,ddc-i2c-bus = <&hdmi_ddc>; + nvidia,hpd-gpio = + <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>; + }; + + sor@0,54540000 { + status = "okay"; + + nvidia,dpaux = <&dpaux>; + nvidia,panel = <&panel>; + }; + + dpaux@0,545c0000 { + vdd-supply = <&vdd_3v3_panel>; + status = "okay"; + }; + }; + + serial@0,70006000 { + /* Debug connector on the bottom of the board near SD card. */ + status = "okay"; + }; + + pwm@0,7000a000 { + status = "okay"; + }; + + i2c@0,7000c000 { + status = "okay"; + clock-frequency = <100000>; + + acodec: audio-codec@10 { + compatible = "maxim,max98090"; + reg = <0x10>; + interrupt-parent = <&gpio>; + interrupts = ; + }; + + temperature-sensor@4c { + compatible = "ti,tmp451"; + reg = <0x4c>; + interrupt-parent = <&gpio>; + interrupts = ; + + #thermal-sensor-cells = <1>; + }; + }; + + i2c@0,7000c400 { + status = "okay"; + clock-frequency = <100000>; + + trackpad@15 { + compatible = "elan,ekth3000"; + reg = <0x15>; + interrupt-parent = <&gpio>; + interrupts = ; + wakeup-source; + }; + }; + + i2c@0,7000c500 { + status = "okay"; + clock-frequency = <400000>; + + tpm@20 { + compatible = "infineon,slb9645tt"; + reg = <0x20>; + }; + }; + + hdmi_ddc: i2c@0,7000c700 { + status = "okay"; + clock-frequency = <100000>; + }; + + i2c@0,7000d000 { + status = "okay"; + clock-frequency = <400000>; + + pmic: pmic@40 { + compatible = "ams,as3722"; + reg = <0x40>; + interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; + + ams,system-power-controller; + + #interrupt-cells = <2>; + interrupt-controller; + + gpio-controller; + #gpio-cells = <2>; + + pinctrl-names = "default"; + pinctrl-0 = <&as3722_default>; + + as3722_default: pinmux { + gpio0 { + pins = "gpio0"; + function = "gpio"; + bias-pull-down; + }; + + gpio1 { + pins = "gpio1"; + function = "gpio"; + bias-pull-up; + }; + + gpio2_4_7 { + pins = "gpio2", "gpio4", "gpio7"; + function = "gpio"; + bias-pull-up; + }; + + gpio3_6 { + pins = "gpio3", "gpio6"; + bias-high-impedance; + }; + + gpio5 { + pins = "gpio5"; + function = "clk32k-out"; + bias-pull-down; + }; + }; + + regulators { + vsup-sd2-supply = <&vdd_5v0_sys>; + vsup-sd3-supply = <&vdd_5v0_sys>; + vsup-sd4-supply = <&vdd_5v0_sys>; + vsup-sd5-supply = <&vdd_5v0_sys>; + vin-ldo0-supply = <&vdd_1v35_lp0>; + vin-ldo1-6-supply = <&vdd_3v3_run>; + vin-ldo2-5-7-supply = <&vddio_1v8>; + vin-ldo3-4-supply = <&vdd_3v3_sys>; + vin-ldo9-10-supply = <&vdd_5v0_sys>; + vin-ldo11-supply = <&vdd_3v3_run>; + + sd0 { + regulator-name = "+VDD_CPU_AP"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-min-microamp = <3500000>; + regulator-max-microamp = <3500000>; + regulator-always-on; + regulator-boot-on; + ams,ext-control = <2>; + }; + + sd1 { + regulator-name = "+VDD_CORE"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-min-microamp = <2500000>; + regulator-max-microamp = <4000000>; + regulator-always-on; + regulator-boot-on; + ams,ext-control = <1>; + }; + + vdd_1v35_lp0: sd2 { + regulator-name = "+1.35V_LP0(sd2)"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + sd3 { + regulator-name = "+1.35V_LP0(sd3)"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v05_run: sd4 { + regulator-name = "+1.05V_RUN"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + vddio_1v8: sd5 { + regulator-name = "+1.8V_VDDIO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + sd6 { + regulator-name = "+VDD_GPU_AP"; + regulator-min-microvolt = <650000>; + regulator-max-microvolt = <1200000>; + regulator-min-microamp = <3500000>; + regulator-max-microamp = <3500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo0 { + regulator-name = "+1.05V_RUN_AVDD"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-boot-on; + regulator-always-on; + ams,ext-control = <1>; + }; + + ldo1 { + regulator-name = "+1.8V_RUN_CAM"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo2 { + regulator-name = "+1.2V_GEN_AVDD"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3 { + regulator-name = "+1.00V_LP0_VDD_RTC"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-boot-on; + regulator-always-on; + ams,enable-tracking; + }; + + vdd_run_cam: ldo4 { + regulator-name = "+3.3V_RUN_CAM"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo5 { + regulator-name = "+1.2V_RUN_CAM_FRONT"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vddio_sdmmc3: ldo6 { + regulator-name = "+VDDIO_SDMMC3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + ldo7 { + regulator-name = "+1.05V_RUN_CAM_REAR"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + ldo9 { + regulator-name = "+2.8V_RUN_TOUCH"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo10 { + regulator-name = "+2.8V_RUN_CAM_AF"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo11 { + regulator-name = "+1.8V_RUN_VPP_FUSE"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + }; + }; + + spi@0,7000d400 { + status = "okay"; + + cros_ec: cros-ec@0 { + compatible = "google,cros-ec-spi"; + spi-max-frequency = <3000000>; + interrupt-parent = <&gpio>; + interrupts = ; + reg = <0>; + + google,cros-ec-spi-msg-delay = <2000>; + + i2c-tunnel { + compatible = "google,cros-ec-i2c-tunnel"; + #address-cells = <1>; + #size-cells = <0>; + + google,remote-bus = <0>; + + charger: bq24735@9 { + compatible = "ti,bq24735"; + reg = <0x9>; + interrupt-parent = <&gpio>; + interrupts = ; + ti,ac-detect-gpios = <&gpio + TEGRA_GPIO(J, 0) + GPIO_ACTIVE_HIGH>; + }; + + battery: sbs-battery@b { + compatible = "sbs,sbs-battery"; + reg = <0xb>; + sbs,i2c-retry-count = <2>; + sbs,poll-retry-count = <10>; + power-supplies = <&charger>; + }; + }; + }; + }; + + spi@0,7000da00 { + status = "okay"; + spi-max-frequency = <25000000>; + + flash@0 { + compatible = "winbond,w25q32dw"; + spi-max-frequency = <25000000>; + reg = <0>; + }; + }; + + pmc@0,7000e400 { + nvidia,invert-interrupt; + nvidia,suspend-mode = <0>; + nvidia,cpu-pwr-good-time = <500>; + nvidia,cpu-pwr-off-time = <300>; + nvidia,core-pwr-good-time = <641 3845>; + nvidia,core-pwr-off-time = <61036>; + nvidia,core-power-req-active-high; + nvidia,sys-clock-req-active-high; + }; + + hda@0,70030000 { + status = "okay"; + }; + + sdhci0_pwrseq: sdhci0_pwrseq { + compatible = "mmc-pwrseq-simple"; + + reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>; + }; + + sdhci@0,700b0000 { /* WiFi/BT on this bus */ + status = "okay"; + bus-width = <4>; + no-1-8-v; + non-removable; + mmc-pwrseq = <&sdhci0_pwrseq>; + vmmc-supply = <&vdd_3v3_lp0>; + vqmmc-supply = <&vddio_1v8>; + keep-power-in-suspend; + }; + + sdhci@0,700b0400 { /* SD Card on this bus */ + status = "okay"; + cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>; + power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>; + bus-width = <4>; + no-1-8-v; + vqmmc-supply = <&vddio_sdmmc3>; + }; + + sdhci@0,700b0600 { /* eMMC on this bus */ + status = "okay"; + bus-width = <8>; + no-1-8-v; + non-removable; + }; + + ahub@0,70300000 { + i2s@0,70301100 { + status = "okay"; + }; + }; + + usb@0,7d000000 { /* Rear external USB port. */ + status = "okay"; + }; + + usb-phy@0,7d000000 { + status = "okay"; + vbus-supply = <&vdd_usb1_vbus>; + }; + + usb@0,7d004000 { /* Internal webcam. */ + status = "okay"; + }; + + usb-phy@0,7d004000 { + status = "okay"; + vbus-supply = <&vdd_run_cam>; + }; + + usb@0,7d008000 { /* Left external USB port. */ + status = "okay"; + }; + + usb-phy@0,7d008000 { + status = "okay"; + vbus-supply = <&vdd_usb3_vbus>; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + + enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>; + power-supply = <&vdd_led>; + pwms = <&pwm 1 1000000>; + + default-brightness-level = <224>; + brightness-levels = + < 0 1 2 3 4 5 6 7 + 8 9 10 11 12 13 14 15 + 16 17 18 19 20 21 22 23 + 24 25 26 27 28 29 30 31 + 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 + 48 49 50 51 52 53 54 55 + 56 57 58 59 60 61 62 63 + 64 65 66 67 68 69 70 71 + 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 + 88 89 90 91 92 93 94 95 + 96 97 98 99 100 101 102 103 + 104 105 106 107 108 109 110 111 + 112 113 114 115 116 117 118 119 + 120 121 122 123 124 125 126 127 + 128 129 130 131 132 133 134 135 + 136 137 138 139 140 141 142 143 + 144 145 146 147 148 149 150 151 + 152 153 154 155 156 157 158 159 + 160 161 162 163 164 165 166 167 + 168 169 170 171 172 173 174 175 + 176 177 178 179 180 181 182 183 + 184 185 186 187 188 189 190 191 + 192 193 194 195 196 197 198 199 + 200 201 202 203 204 205 206 207 + 208 209 210 211 212 213 214 215 + 216 217 218 219 220 221 222 223 + 224 225 226 227 228 229 230 231 + 232 233 234 235 236 237 238 239 + 240 241 242 243 244 245 246 247 + 248 249 250 251 252 253 254 255 + 256>; + }; + + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + clk32k_in: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + lid { + label = "Lid"; + gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>; + linux,input-type = <5>; + linux,code = ; + debounce-interval = <1>; + gpio-key,wakeup; + }; + + power { + label = "Power"; + gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <30>; + gpio-key,wakeup; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + vdd_mux: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "+VDD_MUX"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_5v0_sys: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "+5V_SYS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd_mux>; + }; + + vdd_3v3_sys: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "+3.3V_SYS"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd_mux>; + }; + + vdd_3v3_run: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "+3.3V_RUN"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + gpio = <&pmic 1 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_3v3_sys>; + }; + + vdd_3v3_hdmi: regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "+3.3V_AVDD_HDMI_AP_GATED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vdd_3v3_run>; + }; + + vdd_led: regulator@5 { + compatible = "regulator-fixed"; + reg = <5>; + regulator-name = "+VDD_LED"; + gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_mux>; + }; + + vdd_5v0_ts: regulator@6 { + compatible = "regulator-fixed"; + reg = <6>; + regulator-name = "+5V_VDD_TS_SW"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_5v0_sys>; + }; + + vdd_usb1_vbus: regulator@7 { + compatible = "regulator-fixed"; + reg = <7>; + regulator-name = "+5V_USB_HS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>; + enable-active-high; + gpio-open-drain; + vin-supply = <&vdd_5v0_sys>; + }; + + vdd_usb3_vbus: regulator@8 { + compatible = "regulator-fixed"; + reg = <8>; + regulator-name = "+5V_USB_SS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>; + enable-active-high; + gpio-open-drain; + vin-supply = <&vdd_5v0_sys>; + }; + + vdd_3v3_panel: regulator@9 { + compatible = "regulator-fixed"; + reg = <9>; + regulator-name = "+3.3V_PANEL"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pmic 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_3v3_run>; + }; + + vdd_3v3_lp0: regulator@10 { + compatible = "regulator-fixed"; + reg = <10>; + regulator-name = "+3.3V_LP0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + /* + * TODO: find a way to wire this up with the USB EHCI + * controllers so that it can be enabled on demand. + */ + regulator-always-on; + gpio = <&pmic 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_3v3_sys>; + }; + + vdd_hdmi_pll: regulator@11 { + compatible = "regulator-fixed"; + reg = <11>; + regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>; + vin-supply = <&vdd_1v05_run>; + }; + + vdd_5v0_hdmi: regulator@12 { + compatible = "regulator-fixed"; + reg = <12>; + regulator-name = "+5V_HDMI_CON"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_5v0_sys>; + }; + }; + + sound { + nvidia,audio-routing = + "Headphones", "HPR", + "Headphones", "HPL", + "Speakers", "SPKR", + "Speakers", "SPKL", + "Mic Jack", "MICBIAS", + "DMICL", "Int Mic", + "DMICR", "Int Mic", + "IN34", "Mic Jack"; + + nvidia,i2s-controller = <&tegra_i2s1>; + nvidia,audio-codec = <&acodec>; + + clocks = <&tegra_car TEGRA124_CLK_PLL_A>, + <&tegra_car TEGRA124_CLK_PLL_A_OUT0>, + <&tegra_car TEGRA124_CLK_EXTERN1>; + clock-names = "pll_a", "pll_a_out0", "mclk"; + + nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>; + nvidia,mic-det-gpios = + <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>; + }; + + gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>; + priority = <200>; + }; +}; + +#include "cros-ec-keyboard.dtsi" diff --git a/arch/arm/boot/dts/tegra124.dtsi b/arch/arm/boot/dts/tegra124.dtsi index db85695aa7aa..13cc7ca5e031 100644 --- a/arch/arm/boot/dts/tegra124.dtsi +++ b/arch/arm/boot/dts/tegra124.dtsi @@ -220,6 +220,7 @@ reg = <0x0 0x60006000 0x0 0x1000>; #clock-cells = <1>; #reset-cells = <1>; + nvidia,external-memory-controller = <&emc>; }; flow-controller@0,60007000 { @@ -227,6 +228,17 @@ reg = <0x0 0x60007000 0x0 0x1000>; }; + actmon@0,6000c800 { + compatible = "nvidia,tegra124-actmon"; + reg = <0x0 0x6000c800 0x0 0x400>; + interrupts = ; + clocks = <&tegra_car TEGRA124_CLK_ACTMON>, + <&tegra_car TEGRA124_CLK_EMC>; + clock-names = "actmon", "emc"; + resets = <&tegra_car 119>; + reset-names = "actmon"; + }; + gpio: gpio@0,6000d000 { compatible = "nvidia,tegra124-gpio", "nvidia,tegra30-gpio"; reg = <0x0 0x6000d000 0x0 0x1000>; @@ -582,6 +594,13 @@ #iommu-cells = <1>; }; + emc: emc@0,7001b000 { + compatible = "nvidia,tegra124-emc"; + reg = <0x0 0x7001b000 0x0 0x1000>; + + nvidia,memory-controller = <&mc>; + }; + sata@0,70020000 { compatible = "nvidia,tegra124-ahci"; @@ -807,7 +826,7 @@ <&tegra_car TEGRA124_CLK_PLL_U>, <&tegra_car TEGRA124_CLK_USBD>; clock-names = "reg", "pll_u", "utmi-pads"; - resets = <&tegra_car 59>, <&tegra_car 22>; + resets = <&tegra_car 22>, <&tegra_car 22>; reset-names = "usb", "utmi-pads"; nvidia,hssync-start-delay = <0>; nvidia,idle-wait-delay = <17>; @@ -819,6 +838,7 @@ nvidia,hssquelch-level = <2>; nvidia,hsdiscon-level = <5>; nvidia,xcvr-hsslew = <12>; + nvidia,has-utmi-pad-registers; status = "disabled"; }; @@ -843,7 +863,7 @@ <&tegra_car TEGRA124_CLK_PLL_U>, <&tegra_car TEGRA124_CLK_USBD>; clock-names = "reg", "pll_u", "utmi-pads"; - resets = <&tegra_car 22>, <&tegra_car 22>; + resets = <&tegra_car 58>, <&tegra_car 22>; reset-names = "usb", "utmi-pads"; nvidia,hssync-start-delay = <0>; nvidia,idle-wait-delay = <17>; @@ -855,7 +875,6 @@ nvidia,hssquelch-level = <2>; nvidia,hsdiscon-level = <5>; nvidia,xcvr-hsslew = <12>; - nvidia,has-utmi-pad-registers; status = "disabled"; }; @@ -880,7 +899,7 @@ <&tegra_car TEGRA124_CLK_PLL_U>, <&tegra_car TEGRA124_CLK_USBD>; clock-names = "reg", "pll_u", "utmi-pads"; - resets = <&tegra_car 58>, <&tegra_car 22>; + resets = <&tegra_car 59>, <&tegra_car 22>; reset-names = "usb", "utmi-pads"; nvidia,hssync-start-delay = <0>; nvidia,idle-wait-delay = <17>; diff --git a/arch/arm/boot/dts/tegra30-beaver.dts b/arch/arm/boot/dts/tegra30-beaver.dts index 6b157eeabcc5..3dede3934446 100644 --- a/arch/arm/boot/dts/tegra30-beaver.dts +++ b/arch/arm/boot/dts/tegra30-beaver.dts @@ -62,71 +62,1652 @@ pinctrl-0 = <&state_default>; state_default: pinmux { - sdmmc1_clk_pz0 { - nvidia,pins = "sdmmc1_clk_pz0"; - nvidia,function = "sdmmc1"; + clk_32k_out_pa0 { + nvidia,pins = "clk_32k_out_pa0"; + nvidia,function = "blink"; nvidia,pull = ; nvidia,tristate = ; + nvidia,enable-input = ; }; - sdmmc1_cmd_pz1 { - nvidia,pins = "sdmmc1_cmd_pz1", - "sdmmc1_dat0_py7", - "sdmmc1_dat1_py6", - "sdmmc1_dat2_py5", - "sdmmc1_dat3_py4"; - nvidia,function = "sdmmc1"; - nvidia,pull = ; + uart3_cts_n_pa1 { + nvidia,pins = "uart3_cts_n_pa1"; + nvidia,function = "uartc"; + nvidia,pull = ; nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap2_fs_pa2 { + nvidia,pins = "dap2_fs_pa2"; + nvidia,function = "i2s1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap2_sclk_pa3 { + nvidia,pins = "dap2_sclk_pa3"; + nvidia,function = "i2s1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap2_din_pa4 { + nvidia,pins = "dap2_din_pa4"; + nvidia,function = "i2s1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap2_dout_pa5 { + nvidia,pins = "dap2_dout_pa5"; + nvidia,function = "i2s1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; sdmmc3_clk_pa6 { nvidia,pins = "sdmmc3_clk_pa6"; nvidia,function = "sdmmc3"; nvidia,pull = ; nvidia,tristate = ; + nvidia,enable-input = ; }; sdmmc3_cmd_pa7 { - nvidia,pins = "sdmmc3_cmd_pa7", - "sdmmc3_dat0_pb7", - "sdmmc3_dat1_pb6", - "sdmmc3_dat2_pb5", - "sdmmc3_dat3_pb4"; + nvidia,pins = "sdmmc3_cmd_pa7"; nvidia,function = "sdmmc3"; nvidia,pull = ; nvidia,tristate = ; + nvidia,enable-input = ; }; - sdmmc4_clk_pcc4 { - nvidia,pins = "sdmmc4_clk_pcc4", - "sdmmc4_rst_n_pcc3"; - nvidia,function = "sdmmc4"; + gmi_a17_pb0 { + nvidia,pins = "gmi_a17_pb0"; + nvidia,function = "spi4"; nvidia,pull = ; nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_a18_pb1 { + nvidia,pins = "gmi_a18_pb1"; + nvidia,function = "spi4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_pwr0_pb2 { + nvidia,pins = "lcd_pwr0_pb2"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_pclk_pb3 { + nvidia,pins = "lcd_pclk_pb3"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat3_pb4 { + nvidia,pins = "sdmmc3_dat3_pb4"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat2_pb5 { + nvidia,pins = "sdmmc3_dat2_pb5"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat1_pb6 { + nvidia,pins = "sdmmc3_dat1_pb6"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat0_pb7 { + nvidia,pins = "sdmmc3_dat0_pb7"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart3_rts_n_pc0 { + nvidia,pins = "uart3_rts_n_pc0"; + nvidia,function = "uartc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_pwr1_pc1 { + nvidia,pins = "lcd_pwr1_pc1"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart2_txd_pc2 { + nvidia,pins = "uart2_txd_pc2"; + nvidia,function = "uartb"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart2_rxd_pc3 { + nvidia,pins = "uart2_rxd_pc3"; + nvidia,function = "uartb"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gen1_i2c_scl_pc4 { + nvidia,pins = "gen1_i2c_scl_pc4"; + nvidia,function = "i2c1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + gen1_i2c_sda_pc5 { + nvidia,pins = "gen1_i2c_sda_pc5"; + nvidia,function = "i2c1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + lcd_pwr2_pc6 { + nvidia,pins = "lcd_pwr2_pc6"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_wp_n_pc7 { + nvidia,pins = "gmi_wp_n_pc7"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat5_pd0 { + nvidia,pins = "sdmmc3_dat5_pd0"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat4_pd1 { + nvidia,pins = "sdmmc3_dat4_pd1"; + nvidia,function = "sdmmc3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_dc1_pd2 { + nvidia,pins = "lcd_dc1_pd2"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat6_pd3 { + nvidia,pins = "sdmmc3_dat6_pd3"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc3_dat7_pd4 { + nvidia,pins = "sdmmc3_dat7_pd4"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_d1_pd5 { + nvidia,pins = "vi_d1_pd5"; + nvidia,function = "sdmmc2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_vsync_pd6 { + nvidia,pins = "vi_vsync_pd6"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_hsync_pd7 { + nvidia,pins = "vi_hsync_pd7"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d0_pe0 { + nvidia,pins = "lcd_d0_pe0"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d1_pe1 { + nvidia,pins = "lcd_d1_pe1"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d2_pe2 { + nvidia,pins = "lcd_d2_pe2"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d3_pe3 { + nvidia,pins = "lcd_d3_pe3"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d4_pe4 { + nvidia,pins = "lcd_d4_pe4"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d5_pe5 { + nvidia,pins = "lcd_d5_pe5"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d6_pe6 { + nvidia,pins = "lcd_d6_pe6"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d7_pe7 { + nvidia,pins = "lcd_d7_pe7"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d8_pf0 { + nvidia,pins = "lcd_d8_pf0"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d9_pf1 { + nvidia,pins = "lcd_d9_pf1"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d10_pf2 { + nvidia,pins = "lcd_d10_pf2"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d11_pf3 { + nvidia,pins = "lcd_d11_pf3"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d12_pf4 { + nvidia,pins = "lcd_d12_pf4"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d13_pf5 { + nvidia,pins = "lcd_d13_pf5"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d14_pf6 { + nvidia,pins = "lcd_d14_pf6"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d15_pf7 { + nvidia,pins = "lcd_d15_pf7"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad0_pg0 { + nvidia,pins = "gmi_ad0_pg0"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad1_pg1 { + nvidia,pins = "gmi_ad1_pg1"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad2_pg2 { + nvidia,pins = "gmi_ad2_pg2"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad3_pg3 { + nvidia,pins = "gmi_ad3_pg3"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad4_pg4 { + nvidia,pins = "gmi_ad4_pg4"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad5_pg5 { + nvidia,pins = "gmi_ad5_pg5"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad6_pg6 { + nvidia,pins = "gmi_ad6_pg6"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad7_pg7 { + nvidia,pins = "gmi_ad7_pg7"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad8_ph0 { + nvidia,pins = "gmi_ad8_ph0"; + nvidia,function = "pwm0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad9_ph1 { + nvidia,pins = "gmi_ad9_ph1"; + nvidia,function = "pwm1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad10_ph2 { + nvidia,pins = "gmi_ad10_ph2"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad11_ph3 { + nvidia,pins = "gmi_ad11_ph3"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad12_ph4 { + nvidia,pins = "gmi_ad12_ph4"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad13_ph5 { + nvidia,pins = "gmi_ad13_ph5"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_ad14_ph6 { + nvidia,pins = "gmi_ad14_ph6"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_wr_n_pi0 { + nvidia,pins = "gmi_wr_n_pi0"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_oe_n_pi1 { + nvidia,pins = "gmi_oe_n_pi1"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_dqs_pi2 { + nvidia,pins = "gmi_dqs_pi2"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_iordy_pi5 { + nvidia,pins = "gmi_iordy_pi5"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_cs7_n_pi6 { + nvidia,pins = "gmi_cs7_n_pi6"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_wait_pi7 { + nvidia,pins = "gmi_wait_pi7"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_de_pj1 { + nvidia,pins = "lcd_de_pj1"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_hsync_pj3 { + nvidia,pins = "lcd_hsync_pj3"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_vsync_pj4 { + nvidia,pins = "lcd_vsync_pj4"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart2_cts_n_pj5 { + nvidia,pins = "uart2_cts_n_pj5"; + nvidia,function = "uartb"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart2_rts_n_pj6 { + nvidia,pins = "uart2_rts_n_pj6"; + nvidia,function = "uartb"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_a16_pj7 { + nvidia,pins = "gmi_a16_pj7"; + nvidia,function = "spi4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_adv_n_pk0 { + nvidia,pins = "gmi_adv_n_pk0"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_clk_pk1 { + nvidia,pins = "gmi_clk_pk1"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_cs2_n_pk3 { + nvidia,pins = "gmi_cs2_n_pk3"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_cs3_n_pk4 { + nvidia,pins = "gmi_cs3_n_pk4"; + nvidia,function = "nand"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + spdif_out_pk5 { + nvidia,pins = "spdif_out_pk5"; + nvidia,function = "spdif"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + spdif_in_pk6 { + nvidia,pins = "spdif_in_pk6"; + nvidia,function = "spdif"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gmi_a19_pk7 { + nvidia,pins = "gmi_a19_pk7"; + nvidia,function = "spi4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_d2_pl0 { + nvidia,pins = "vi_d2_pl0"; + nvidia,function = "sdmmc2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_d3_pl1 { + nvidia,pins = "vi_d3_pl1"; + nvidia,function = "sdmmc2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_d4_pl2 { + nvidia,pins = "vi_d4_pl2"; + nvidia,function = "vi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_d5_pl3 { + nvidia,pins = "vi_d5_pl3"; + nvidia,function = "sdmmc2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_d6_pl4 { + nvidia,pins = "vi_d6_pl4"; + nvidia,function = "vi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_d7_pl5 { + nvidia,pins = "vi_d7_pl5"; + nvidia,function = "sdmmc2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_d8_pl6 { + nvidia,pins = "vi_d8_pl6"; + nvidia,function = "sdmmc2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_d9_pl7 { + nvidia,pins = "vi_d9_pl7"; + nvidia,function = "sdmmc2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d16_pm0 { + nvidia,pins = "lcd_d16_pm0"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d17_pm1 { + nvidia,pins = "lcd_d17_pm1"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d18_pm2 { + nvidia,pins = "lcd_d18_pm2"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d19_pm3 { + nvidia,pins = "lcd_d19_pm3"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d20_pm4 { + nvidia,pins = "lcd_d20_pm4"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d21_pm5 { + nvidia,pins = "lcd_d21_pm5"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d22_pm6 { + nvidia,pins = "lcd_d22_pm6"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_d23_pm7 { + nvidia,pins = "lcd_d23_pm7"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap1_fs_pn0 { + nvidia,pins = "dap1_fs_pn0"; + nvidia,function = "i2s0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap1_din_pn1 { + nvidia,pins = "dap1_din_pn1"; + nvidia,function = "i2s0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap1_dout_pn2 { + nvidia,pins = "dap1_dout_pn2"; + nvidia,function = "i2s0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap1_sclk_pn3 { + nvidia,pins = "dap1_sclk_pn3"; + nvidia,function = "i2s0"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_cs0_n_pn4 { + nvidia,pins = "lcd_cs0_n_pn4"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_sdout_pn5 { + nvidia,pins = "lcd_sdout_pn5"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_dc0_pn6 { + nvidia,pins = "lcd_dc0_pn6"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + hdmi_int_pn7 { + nvidia,pins = "hdmi_int_pn7"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data7_po0 { + nvidia,pins = "ulpi_data7_po0"; + nvidia,function = "uarta"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data0_po1 { + nvidia,pins = "ulpi_data0_po1"; + nvidia,function = "uarta"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data1_po2 { + nvidia,pins = "ulpi_data1_po2"; + nvidia,function = "uarta"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data2_po3 { + nvidia,pins = "ulpi_data2_po3"; + nvidia,function = "uarta"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data3_po4 { + nvidia,pins = "ulpi_data3_po4"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data4_po5 { + nvidia,pins = "ulpi_data4_po5"; + nvidia,function = "uarta"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data5_po6 { + nvidia,pins = "ulpi_data5_po6"; + nvidia,function = "uarta"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_data6_po7 { + nvidia,pins = "ulpi_data6_po7"; + nvidia,function = "uarta"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap3_fs_pp0 { + nvidia,pins = "dap3_fs_pp0"; + nvidia,function = "i2s2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap3_din_pp1 { + nvidia,pins = "dap3_din_pp1"; + nvidia,function = "i2s2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap3_dout_pp2 { + nvidia,pins = "dap3_dout_pp2"; + nvidia,function = "i2s2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap3_sclk_pp3 { + nvidia,pins = "dap3_sclk_pp3"; + nvidia,function = "i2s2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap4_fs_pp4 { + nvidia,pins = "dap4_fs_pp4"; + nvidia,function = "i2s3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap4_din_pp5 { + nvidia,pins = "dap4_din_pp5"; + nvidia,function = "i2s3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap4_dout_pp6 { + nvidia,pins = "dap4_dout_pp6"; + nvidia,function = "i2s3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + dap4_sclk_pp7 { + nvidia,pins = "dap4_sclk_pp7"; + nvidia,function = "i2s3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col0_pq0 { + nvidia,pins = "kb_col0_pq0"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col1_pq1 { + nvidia,pins = "kb_col1_pq1"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col2_pq2 { + nvidia,pins = "kb_col2_pq2"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col3_pq3 { + nvidia,pins = "kb_col3_pq3"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col4_pq4 { + nvidia,pins = "kb_col4_pq4"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col5_pq5 { + nvidia,pins = "kb_col5_pq5"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col6_pq6 { + nvidia,pins = "kb_col6_pq6"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_col7_pq7 { + nvidia,pins = "kb_col7_pq7"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row0_pr0 { + nvidia,pins = "kb_row0_pr0"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row1_pr1 { + nvidia,pins = "kb_row1_pr1"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row2_pr2 { + nvidia,pins = "kb_row2_pr2"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row3_pr3 { + nvidia,pins = "kb_row3_pr3"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row4_pr4 { + nvidia,pins = "kb_row4_pr4"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row5_pr5 { + nvidia,pins = "kb_row5_pr5"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row6_pr6 { + nvidia,pins = "kb_row6_pr6"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row7_pr7 { + nvidia,pins = "kb_row7_pr7"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row8_ps0 { + nvidia,pins = "kb_row8_ps0"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row9_ps1 { + nvidia,pins = "kb_row9_ps1"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row10_ps2 { + nvidia,pins = "kb_row10_ps2"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row11_ps3 { + nvidia,pins = "kb_row11_ps3"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row12_ps4 { + nvidia,pins = "kb_row12_ps4"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row13_ps5 { + nvidia,pins = "kb_row13_ps5"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row14_ps6 { + nvidia,pins = "kb_row14_ps6"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + kb_row15_ps7 { + nvidia,pins = "kb_row15_ps7"; + nvidia,function = "kbc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_pclk_pt0 { + nvidia,pins = "vi_pclk_pt0"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_mclk_pt1 { + nvidia,pins = "vi_mclk_pt1"; + nvidia,function = "vi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_d10_pt2 { + nvidia,pins = "vi_d10_pt2"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_d11_pt3 { + nvidia,pins = "vi_d11_pt3"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + vi_d0_pt4 { + nvidia,pins = "vi_d0_pt4"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + gen2_i2c_scl_pt5 { + nvidia,pins = "gen2_i2c_scl_pt5"; + nvidia,function = "i2c2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + gen2_i2c_sda_pt6 { + nvidia,pins = "gen2_i2c_sda_pt6"; + nvidia,function = "i2c2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + sdmmc4_cmd_pt7 { + nvidia,pins = "sdmmc4_cmd_pt7"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu0 { + nvidia,pins = "pu0"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu1 { + nvidia,pins = "pu1"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu2 { + nvidia,pins = "pu2"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu3 { + nvidia,pins = "pu3"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu4 { + nvidia,pins = "pu4"; + nvidia,function = "pwm1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu5 { + nvidia,pins = "pu5"; + nvidia,function = "pwm2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pu6 { + nvidia,pins = "pu6"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + jtag_rtck_pu7 { + nvidia,pins = "jtag_rtck_pu7"; + nvidia,function = "rtck"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pv0 { + nvidia,pins = "pv0"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pv2 { + nvidia,pins = "pv2"; + nvidia,function = "owr"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pv3 { + nvidia,pins = "pv3"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ddc_scl_pv4 { + nvidia,pins = "ddc_scl_pv4"; + nvidia,function = "i2c4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ddc_sda_pv5 { + nvidia,pins = "ddc_sda_pv5"; + nvidia,function = "i2c4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + crt_hsync_pv6 { + nvidia,pins = "crt_hsync_pv6"; + nvidia,function = "crt"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + crt_vsync_pv7 { + nvidia,pins = "crt_vsync_pv7"; + nvidia,function = "crt"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_cs1_n_pw0 { + nvidia,pins = "lcd_cs1_n_pw0"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_m1_pw1 { + nvidia,pins = "lcd_m1_pw1"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + spi2_cs1_n_pw2 { + nvidia,pins = "spi2_cs1_n_pw2"; + nvidia,function = "spi2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk1_out_pw4 { + nvidia,pins = "clk1_out_pw4"; + nvidia,function = "extperiph1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk2_out_pw5 { + nvidia,pins = "clk2_out_pw5"; + nvidia,function = "extperiph2"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart3_txd_pw6 { + nvidia,pins = "uart3_txd_pw6"; + nvidia,function = "uartc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + uart3_rxd_pw7 { + nvidia,pins = "uart3_rxd_pw7"; + nvidia,function = "uartc"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + spi2_sck_px2 { + nvidia,pins = "spi2_sck_px2"; + nvidia,function = "gmi"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + spi1_mosi_px4 { + nvidia,pins = "spi1_mosi_px4"; + nvidia,function = "spi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + spi1_sck_px5 { + nvidia,pins = "spi1_sck_px5"; + nvidia,function = "spi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + spi1_cs0_n_px6 { + nvidia,pins = "spi1_cs0_n_px6"; + nvidia,function = "spi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + spi1_miso_px7 { + nvidia,pins = "spi1_miso_px7"; + nvidia,function = "spi1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_clk_py0 { + nvidia,pins = "ulpi_clk_py0"; + nvidia,function = "uartd"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_dir_py1 { + nvidia,pins = "ulpi_dir_py1"; + nvidia,function = "uartd"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_nxt_py2 { + nvidia,pins = "ulpi_nxt_py2"; + nvidia,function = "uartd"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + ulpi_stp_py3 { + nvidia,pins = "ulpi_stp_py3"; + nvidia,function = "uartd"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_dat3_py4 { + nvidia,pins = "sdmmc1_dat3_py4"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_dat2_py5 { + nvidia,pins = "sdmmc1_dat2_py5"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_dat1_py6 { + nvidia,pins = "sdmmc1_dat1_py6"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_dat0_py7 { + nvidia,pins = "sdmmc1_dat0_py7"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_clk_pz0 { + nvidia,pins = "sdmmc1_clk_pz0"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc1_cmd_pz1 { + nvidia,pins = "sdmmc1_cmd_pz1"; + nvidia,function = "sdmmc1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_sdin_pz2 { + nvidia,pins = "lcd_sdin_pz2"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_wr_n_pz3 { + nvidia,pins = "lcd_wr_n_pz3"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + lcd_sck_pz4 { + nvidia,pins = "lcd_sck_pz4"; + nvidia,function = "displaya"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sys_clk_req_pz5 { + nvidia,pins = "sys_clk_req_pz5"; + nvidia,function = "sysclk"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pwr_i2c_scl_pz6 { + nvidia,pins = "pwr_i2c_scl_pz6"; + nvidia,function = "i2cpwr"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + pwr_i2c_sda_pz7 { + nvidia,pins = "pwr_i2c_sda_pz7"; + nvidia,function = "i2cpwr"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; }; sdmmc4_dat0_paa0 { - nvidia,pins = "sdmmc4_dat0_paa0", - "sdmmc4_dat1_paa1", - "sdmmc4_dat2_paa2", - "sdmmc4_dat3_paa3", - "sdmmc4_dat4_paa4", - "sdmmc4_dat5_paa5", - "sdmmc4_dat6_paa6", - "sdmmc4_dat7_paa7"; + nvidia,pins = "sdmmc4_dat0_paa0"; nvidia,function = "sdmmc4"; nvidia,pull = ; nvidia,tristate = ; + nvidia,enable-input = ; }; - dap2_fs_pa2 { - nvidia,pins = "dap2_fs_pa2", - "dap2_sclk_pa3", - "dap2_din_pa4", - "dap2_dout_pa5"; - nvidia,function = "i2s1"; + sdmmc4_dat1_paa1 { + nvidia,pins = "sdmmc4_dat1_paa1"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat2_paa2 { + nvidia,pins = "sdmmc4_dat2_paa2"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat3_paa3 { + nvidia,pins = "sdmmc4_dat3_paa3"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat4_paa4 { + nvidia,pins = "sdmmc4_dat4_paa4"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat5_paa5 { + nvidia,pins = "sdmmc4_dat5_paa5"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat6_paa6 { + nvidia,pins = "sdmmc4_dat6_paa6"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_dat7_paa7 { + nvidia,pins = "sdmmc4_dat7_paa7"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb0 { + nvidia,pins = "pbb0"; + nvidia,function = "rsvd1"; nvidia,pull = ; nvidia,tristate = ; + nvidia,enable-input = ; + }; + cam_i2c_scl_pbb1 { + nvidia,pins = "cam_i2c_scl_pbb1"; + nvidia,function = "i2c3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + cam_i2c_sda_pbb2 { + nvidia,pins = "cam_i2c_sda_pbb2"; + nvidia,function = "i2c3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + pbb3 { + nvidia,pins = "pbb3"; + nvidia,function = "vgp3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb4 { + nvidia,pins = "pbb4"; + nvidia,function = "vgp4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb5 { + nvidia,pins = "pbb5"; + nvidia,function = "vgp5"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb6 { + nvidia,pins = "pbb6"; + nvidia,function = "vgp6"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pbb7 { + nvidia,pins = "pbb7"; + nvidia,function = "i2s4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + cam_mclk_pcc0 { + nvidia,pins = "cam_mclk_pcc0"; + nvidia,function = "vi_alt3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pcc1 { + nvidia,pins = "pcc1"; + nvidia,function = "rsvd1"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pcc2 { + nvidia,pins = "pcc2"; + nvidia,function = "i2s4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_rst_n_pcc3 { + nvidia,pins = "sdmmc4_rst_n_pcc3"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + sdmmc4_clk_pcc4 { + nvidia,pins = "sdmmc4_clk_pcc4"; + nvidia,function = "sdmmc4"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk2_req_pcc5 { + nvidia,pins = "clk2_req_pcc5"; + nvidia,function = "dap"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l2_rst_n_pcc6 { + nvidia,pins = "pex_l2_rst_n_pcc6"; + nvidia,function = "pcie"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l2_clkreq_n_pcc7 { + nvidia,pins = "pex_l2_clkreq_n_pcc7"; + nvidia,function = "pcie"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l0_prsnt_n_pdd0 { + nvidia,pins = "pex_l0_prsnt_n_pdd0"; + nvidia,function = "pcie"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l0_rst_n_pdd1 { + nvidia,pins = "pex_l0_rst_n_pdd1"; + nvidia,function = "pcie"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l0_clkreq_n_pdd2 { + nvidia,pins = "pex_l0_clkreq_n_pdd2"; + nvidia,function = "pcie"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_wake_n_pdd3 { + nvidia,pins = "pex_wake_n_pdd3"; + nvidia,function = "pcie"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; pex_l1_prsnt_n_pdd4 { - nvidia,pins = "pex_l1_prsnt_n_pdd4", - "pex_l1_clkreq_n_pdd6"; + nvidia,pins = "pex_l1_prsnt_n_pdd4"; + nvidia,function = "pcie"; nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l1_rst_n_pdd5 { + nvidia,pins = "pex_l1_rst_n_pdd5"; + nvidia,function = "pcie"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l1_clkreq_n_pdd6 { + nvidia,pins = "pex_l1_clkreq_n_pdd6"; + nvidia,function = "pcie"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + pex_l2_prsnt_n_pdd7 { + nvidia,pins = "pex_l2_prsnt_n_pdd7"; + nvidia,function = "pcie"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk3_out_pee0 { + nvidia,pins = "clk3_out_pee0"; + nvidia,function = "extperiph3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk3_req_pee1 { + nvidia,pins = "clk3_req_pee1"; + nvidia,function = "dev3"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + clk1_req_pee2 { + nvidia,pins = "clk1_req_pee2"; + nvidia,function = "dap"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + }; + hdmi_cec_pee3 { + nvidia,pins = "hdmi_cec_pee3"; + nvidia,function = "cec"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; + nvidia,open-drain = ; + }; + owr { + nvidia,pins = "owr"; + nvidia,function = "owr"; + nvidia,pull = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; sdio3 { nvidia,pins = "drive_sdio3"; diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts index 33920df03640..107395c32d82 100644 --- a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts +++ b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts @@ -191,6 +191,7 @@ compatible = "arm,cortex-a15-pmu"; interrupts = <0 68 4>, <0 69 4>; + interrupt-affinity = <&cpu0>, <&cpu1>; }; oscclk6a: oscclk6a { @@ -362,7 +363,6 @@ compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0 0x20010000 0 0x1000>; - coresight-default-sink; clocks = <&oscclk6a>; clock-names = "apb_pclk"; port { diff --git a/arch/arm/boot/dts/vexpress-v2p-ca9.dts b/arch/arm/boot/dts/vexpress-v2p-ca9.dts index 23662b5a5e9d..d949facba376 100644 --- a/arch/arm/boot/dts/vexpress-v2p-ca9.dts +++ b/arch/arm/boot/dts/vexpress-v2p-ca9.dts @@ -33,28 +33,28 @@ #address-cells = <1>; #size-cells = <0>; - cpu@0 { + A9_0: cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0>; next-level-cache = <&L2>; }; - cpu@1 { + A9_1: cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <1>; next-level-cache = <&L2>; }; - cpu@2 { + A9_2: cpu@2 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <2>; next-level-cache = <&L2>; }; - cpu@3 { + A9_3: cpu@3 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <3>; @@ -170,6 +170,7 @@ compatible = "arm,pl310-cache"; reg = <0x1e00a000 0x1000>; interrupts = <0 43 4>; + cache-unified; cache-level = <2>; arm,data-latency = <1 1 1>; arm,tag-latency = <1 1 1>; @@ -181,6 +182,8 @@ <0 61 4>, <0 62 4>, <0 63 4>; + interrupt-affinity = <&A9_0>, <&A9_1>, <&A9_2>, <&A9_3>; + }; dcc { diff --git a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi index 36cafbfa1bfa..606753eb72c8 100644 --- a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi +++ b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi @@ -12,6 +12,12 @@ bootargs = "console=ttyLP0,115200"; }; + clk16m: clk16m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <16000000>; + }; + regulators { compatible = "simple-bus"; #address-cells = <1>; @@ -47,6 +53,21 @@ status = "okay"; }; +&dspi1 { + status = "okay"; + + mcp2515can: can@0 { + compatible = "microchip,mcp2515"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can_int>; + reg = <0>; + clocks = <&clk16m>; + spi-max-frequency = <10000000>; + interrupt-parent = <&gpio1>; + interrupts = <11 GPIO_ACTIVE_LOW>; + }; +}; + &esdhc1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_esdhc1>; @@ -94,3 +115,13 @@ &usbh1 { vbus-supply = <&usbh_vbus_reg>; }; + +&iomuxc { + vf610-colibri { + pinctrl_can_int: can_int { + fsl,pins = < + VF610_PAD_PTB21__GPIO_43 0x22ed + >; + }; + }; +}; diff --git a/arch/arm/boot/dts/vf-colibri.dtsi b/arch/arm/boot/dts/vf-colibri.dtsi index 5c2b7320856d..fbef0828e930 100644 --- a/arch/arm/boot/dts/vf-colibri.dtsi +++ b/arch/arm/boot/dts/vf-colibri.dtsi @@ -23,6 +23,12 @@ status = "okay"; }; +&dspi1 { + bus-num = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dspi1>; +}; + &edma0 { status = "okay"; }; @@ -107,6 +113,15 @@ >; }; + pinctrl_dspi1: dspi1grp { + fsl,pins = < + VF610_PAD_PTD5__DSPI1_CS0 0x33e2 + VF610_PAD_PTD6__DSPI1_SIN 0x33e1 + VF610_PAD_PTD7__DSPI1_SOUT 0x33e2 + VF610_PAD_PTD8__DSPI1_SCK 0x33e2 + >; + }; + pinctrl_esdhc1: esdhc1grp { fsl,pins = < VF610_PAD_PTA24__ESDHC1_CLK 0x31ef diff --git a/arch/arm/boot/dts/vf500.dtsi b/arch/arm/boot/dts/vf500.dtsi index 1dbf8d2d1ddf..e976d2fa1527 100644 --- a/arch/arm/boot/dts/vf500.dtsi +++ b/arch/arm/boot/dts/vf500.dtsi @@ -24,14 +24,13 @@ }; soc { - interrupt-parent = <&intc>; - aips-bus@40000000 { intc: interrupt-controller@40002000 { compatible = "arm,cortex-a9-gic"; #interrupt-cells = <3>; interrupt-controller; + interrupt-parent = <&intc>; reg = <0x40003000 0x1000>, <0x40002100 0x100>; }; @@ -40,145 +39,17 @@ compatible = "arm,cortex-a9-global-timer"; reg = <0x40002200 0x20>; interrupts = ; + interrupt-parent = <&intc>; clocks = <&clks VF610_CLK_PLATFORM_BUS>; }; }; }; }; -&adc0 { - interrupts = ; -}; - -&adc1 { - interrupts = ; -}; - -&can0 { - interrupts = ; -}; - -&can1 { - interrupts = ; -}; - -&dspi0 { - interrupts = ; -}; - -&edma0 { - interrupts = , - ; - interrupt-names = "edma-tx", "edma-err"; -}; - -&edma1 { - interrupts = , - ; - interrupt-names = "edma-tx", "edma-err"; -}; - -&esdhc1 { - interrupts = ; -}; - -&fec0 { - interrupts = ; -}; - -&fec1 { - interrupts = ; -}; - -&ftm { - interrupts = ; -}; - -&gpio0 { - interrupts = ; -}; - -&gpio1 { - interrupts = ; -}; - -&gpio2 { - interrupts = ; -}; - -&gpio3 { - interrupts = ; -}; - -&gpio4 { - interrupts = ; -}; - -&i2c0 { - interrupts = ; -}; - -&pit { - interrupts = ; -}; - -&qspi0 { - interrupts = ; -}; - -&sai2 { - interrupts = ; -}; - -&snvsrtc { - interrupts = ; -}; - -&src { - interrupts = ; -}; - -&uart0 { - interrupts = ; -}; - -&uart1 { - interrupts = ; -}; - -&uart2 { - interrupts = ; -}; - -&uart3 { - interrupts = ; -}; - -&uart4 { - interrupts = ; -}; - -&uart5 { - interrupts = ; -}; - -&usbdev0 { - interrupts = ; -}; - -&usbh1 { - interrupts = ; -}; - -&usbphy0 { - interrupts = ; -}; - -&usbphy1 { - interrupts = ; +&mscm_ir { + interrupt-parent = <&intc>; }; &wdoga5 { - interrupts = ; status = "okay"; }; diff --git a/arch/arm/boot/dts/vfxxx.dtsi b/arch/arm/boot/dts/vfxxx.dtsi index a29c7ce15eaf..4aa335166be7 100644 --- a/arch/arm/boot/dts/vfxxx.dtsi +++ b/arch/arm/boot/dts/vfxxx.dtsi @@ -54,6 +54,7 @@ #address-cells = <1>; #size-cells = <1>; compatible = "simple-bus"; + interrupt-parent = <&mscm_ir>; ranges; aips0: aips-bus@40000000 { @@ -62,6 +63,19 @@ #size-cells = <1>; ranges; + mscm_cpucfg: cpucfg@40001000 { + compatible = "fsl,vf610-mscm-cpucfg", "syscon"; + reg = <0x40001000 0x800>; + }; + + mscm_ir: interrupt-controller@40001800 { + compatible = "fsl,vf610-mscm-ir"; + reg = <0x40001800 0x400>; + fsl,cpucfg = <&mscm_cpucfg>; + interrupt-controller; + #interrupt-cells = <2>; + }; + edma0: dma-controller@40018000 { #dma-cells = <2>; compatible = "fsl,vf610-edma"; @@ -69,6 +83,9 @@ <0x40024000 0x1000>, <0x40025000 0x1000>; dma-channels = <32>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>, + <9 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "edma-tx", "edma-err"; clock-names = "dmamux0", "dmamux1"; clocks = <&clks VF610_CLK_DMAMUX0>, <&clks VF610_CLK_DMAMUX1>; @@ -78,6 +95,7 @@ can0: flexcan@40020000 { compatible = "fsl,vf610-flexcan"; reg = <0x40020000 0x4000>; + interrupts = <58 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_FLEXCAN0>, <&clks VF610_CLK_FLEXCAN0>; clock-names = "ipg", "per"; @@ -87,6 +105,7 @@ uart0: serial@40027000 { compatible = "fsl,vf610-lpuart"; reg = <0x40027000 0x1000>; + interrupts = <61 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_UART0>; clock-names = "ipg"; dmas = <&edma0 0 2>, @@ -98,6 +117,7 @@ uart1: serial@40028000 { compatible = "fsl,vf610-lpuart"; reg = <0x40028000 0x1000>; + interrupts = <62 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_UART1>; clock-names = "ipg"; dmas = <&edma0 0 4>, @@ -109,6 +129,7 @@ uart2: serial@40029000 { compatible = "fsl,vf610-lpuart"; reg = <0x40029000 0x1000>; + interrupts = <63 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_UART2>; clock-names = "ipg"; dmas = <&edma0 0 6>, @@ -120,6 +141,7 @@ uart3: serial@4002a000 { compatible = "fsl,vf610-lpuart"; reg = <0x4002a000 0x1000>; + interrupts = <64 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_UART3>; clock-names = "ipg"; dmas = <&edma0 0 8>, @@ -133,15 +155,29 @@ #size-cells = <0>; compatible = "fsl,vf610-dspi"; reg = <0x4002c000 0x1000>; + interrupts = <67 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_DSPI0>; clock-names = "dspi"; spi-num-chipselects = <5>; status = "disabled"; }; + dspi1: dspi1@4002d000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,vf610-dspi"; + reg = <0x4002d000 0x1000>; + interrupts = <68 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks VF610_CLK_DSPI1>; + clock-names = "dspi"; + spi-num-chipselects = <5>; + status = "disabled"; + }; + sai2: sai@40031000 { compatible = "fsl,vf610-sai"; reg = <0x40031000 0x1000>; + interrupts = <86 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_SAI2>; clock-names = "sai"; dma-names = "tx", "rx"; @@ -153,6 +189,7 @@ pit: pit@40037000 { compatible = "fsl,vf610-pit"; reg = <0x40037000 0x1000>; + interrupts = <39 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_PIT>; clock-names = "pit"; }; @@ -186,6 +223,7 @@ adc0: adc@4003b000 { compatible = "fsl,vf610-adc"; reg = <0x4003b000 0x1000>; + interrupts = <53 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_ADC0>; clock-names = "adc"; status = "disabled"; @@ -194,6 +232,7 @@ wdoga5: wdog@4003e000 { compatible = "fsl,vf610-wdt", "fsl,imx21-wdt"; reg = <0x4003e000 0x1000>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_WDT>; clock-names = "wdog"; status = "disabled"; @@ -204,6 +243,7 @@ #size-cells = <0>; compatible = "fsl,vf610-qspi"; reg = <0x40044000 0x1000>; + interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_QSPI0_EN>, <&clks VF610_CLK_QSPI0>; clock-names = "qspi_en", "qspi"; @@ -213,7 +253,6 @@ iomuxc: iomuxc@40048000 { compatible = "fsl,vf610-iomuxc"; reg = <0x40048000 0x1000>; - #gpio-range-cells = <3>; }; gpio0: gpio@40049000 { @@ -221,6 +260,7 @@ reg = <0x40049000 0x1000 0x400ff000 0x40>; gpio-controller; #gpio-cells = <2>; + interrupts = <107 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; #interrupt-cells = <2>; gpio-ranges = <&iomuxc 0 0 32>; @@ -231,6 +271,7 @@ reg = <0x4004a000 0x1000 0x400ff040 0x40>; gpio-controller; #gpio-cells = <2>; + interrupts = <108 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; #interrupt-cells = <2>; gpio-ranges = <&iomuxc 0 32 32>; @@ -241,6 +282,7 @@ reg = <0x4004b000 0x1000 0x400ff080 0x40>; gpio-controller; #gpio-cells = <2>; + interrupts = <109 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; #interrupt-cells = <2>; gpio-ranges = <&iomuxc 0 64 32>; @@ -251,6 +293,7 @@ reg = <0x4004c000 0x1000 0x400ff0c0 0x40>; gpio-controller; #gpio-cells = <2>; + interrupts = <110 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; #interrupt-cells = <2>; gpio-ranges = <&iomuxc 0 96 32>; @@ -261,6 +304,7 @@ reg = <0x4004d000 0x1000 0x400ff100 0x40>; gpio-controller; #gpio-cells = <2>; + interrupts = <111 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; #interrupt-cells = <2>; gpio-ranges = <&iomuxc 0 128 7>; @@ -274,6 +318,7 @@ usbphy0: usbphy@40050800 { compatible = "fsl,vf610-usbphy"; reg = <0x40050800 0x400>; + interrupts = <50 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_USBPHY0>; fsl,anatop = <&anatop>; status = "disabled"; @@ -282,6 +327,7 @@ usbphy1: usbphy@40050c00 { compatible = "fsl,vf610-usbphy"; reg = <0x40050c00 0x400>; + interrupts = <51 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_USBPHY1>; fsl,anatop = <&anatop>; status = "disabled"; @@ -292,6 +338,7 @@ #size-cells = <0>; compatible = "fsl,vf610-i2c"; reg = <0x40066000 0x1000>; + interrupts = <71 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_I2C0>; clock-names = "ipg"; dmas = <&edma0 0 50>, @@ -311,6 +358,7 @@ usbdev0: usb@40034000 { compatible = "fsl,vf610-usb", "fsl,imx27-usb"; reg = <0x40034000 0x800>; + interrupts = <75 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_USBC0>; fsl,usbphy = <&usbphy0>; fsl,usbmisc = <&usbmisc0 0>; @@ -329,6 +377,7 @@ src: src@4006e000 { compatible = "fsl,vf610-src", "syscon"; reg = <0x4006e000 0x1000>; + interrupts = <96 IRQ_TYPE_LEVEL_HIGH>; }; }; @@ -345,6 +394,9 @@ <0x400a1000 0x1000>, <0x400a2000 0x1000>; dma-channels = <32>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>, + <11 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "edma-tx", "edma-err"; clock-names = "dmamux0", "dmamux1"; clocks = <&clks VF610_CLK_DMAMUX2>, <&clks VF610_CLK_DMAMUX3>; @@ -360,6 +412,7 @@ snvsrtc: snvs-rtc-lp@34 { compatible = "fsl,sec-v4.0-mon-rtc-lp"; reg = <0x34 0x58>; + interrupts = <100 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_SNVS>; clock-names = "snvs-rtc"; }; @@ -368,6 +421,7 @@ uart4: serial@400a9000 { compatible = "fsl,vf610-lpuart"; reg = <0x400a9000 0x1000>; + interrupts = <65 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_UART4>; clock-names = "ipg"; status = "disabled"; @@ -376,6 +430,7 @@ uart5: serial@400aa000 { compatible = "fsl,vf610-lpuart"; reg = <0x400aa000 0x1000>; + interrupts = <66 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_UART5>; clock-names = "ipg"; status = "disabled"; @@ -384,6 +439,7 @@ adc1: adc@400bb000 { compatible = "fsl,vf610-adc"; reg = <0x400bb000 0x1000>; + interrupts = <54 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_ADC1>; clock-names = "adc"; status = "disabled"; @@ -392,6 +448,7 @@ esdhc1: esdhc@400b2000 { compatible = "fsl,imx53-esdhc"; reg = <0x400b2000 0x1000>; + interrupts = <28 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_IPG_BUS>, <&clks VF610_CLK_PLATFORM_BUS>, <&clks VF610_CLK_ESDHC1>; @@ -402,6 +459,7 @@ usbh1: usb@400b4000 { compatible = "fsl,vf610-usb", "fsl,imx27-usb"; reg = <0x400b4000 0x800>; + interrupts = <76 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_USBC1>; fsl,usbphy = <&usbphy1>; fsl,usbmisc = <&usbmisc1 0>; @@ -420,6 +478,7 @@ ftm: ftm@400b8000 { compatible = "fsl,ftm-timer"; reg = <0x400b8000 0x1000 0x400b9000 0x1000>; + interrupts = <44 IRQ_TYPE_LEVEL_HIGH>; clock-names = "ftm-evt", "ftm-src", "ftm-evt-counter-en", "ftm-src-counter-en"; clocks = <&clks VF610_CLK_FTM2>, @@ -432,6 +491,7 @@ fec0: ethernet@400d0000 { compatible = "fsl,mvf600-fec"; reg = <0x400d0000 0x1000>; + interrupts = <78 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_ENET0>, <&clks VF610_CLK_ENET0>, <&clks VF610_CLK_ENET>; @@ -442,6 +502,7 @@ fec1: ethernet@400d1000 { compatible = "fsl,mvf600-fec"; reg = <0x400d1000 0x1000>; + interrupts = <79 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_ENET1>, <&clks VF610_CLK_ENET1>, <&clks VF610_CLK_ENET>; @@ -452,6 +513,7 @@ can1: flexcan@400d4000 { compatible = "fsl,vf610-flexcan"; reg = <0x400d4000 0x4000>; + interrupts = <59 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_FLEXCAN1>, <&clks VF610_CLK_FLEXCAN1>; clock-names = "ipg", "per"; diff --git a/arch/arm/common/mcpm_entry.c b/arch/arm/common/mcpm_entry.c index 3c165fc2dce2..5f8a52ac7edf 100644 --- a/arch/arm/common/mcpm_entry.c +++ b/arch/arm/common/mcpm_entry.c @@ -55,22 +55,81 @@ bool mcpm_is_available(void) return (platform_ops) ? true : false; } +/* + * We can't use regular spinlocks. In the switcher case, it is possible + * for an outbound CPU to call power_down() after its inbound counterpart + * is already live using the same logical CPU number which trips lockdep + * debugging. + */ +static arch_spinlock_t mcpm_lock = __ARCH_SPIN_LOCK_UNLOCKED; + +static int mcpm_cpu_use_count[MAX_NR_CLUSTERS][MAX_CPUS_PER_CLUSTER]; + +static inline bool mcpm_cluster_unused(unsigned int cluster) +{ + int i, cnt; + for (i = 0, cnt = 0; i < MAX_CPUS_PER_CLUSTER; i++) + cnt |= mcpm_cpu_use_count[cluster][i]; + return !cnt; +} + int mcpm_cpu_power_up(unsigned int cpu, unsigned int cluster) { + bool cpu_is_down, cluster_is_down; + int ret = 0; + if (!platform_ops) return -EUNATCH; /* try not to shadow power_up errors */ might_sleep(); - return platform_ops->power_up(cpu, cluster); + + /* backward compatibility callback */ + if (platform_ops->power_up) + return platform_ops->power_up(cpu, cluster); + + pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster); + + /* + * Since this is called with IRQs enabled, and no arch_spin_lock_irq + * variant exists, we need to disable IRQs manually here. + */ + local_irq_disable(); + arch_spin_lock(&mcpm_lock); + + cpu_is_down = !mcpm_cpu_use_count[cluster][cpu]; + cluster_is_down = mcpm_cluster_unused(cluster); + + mcpm_cpu_use_count[cluster][cpu]++; + /* + * The only possible values are: + * 0 = CPU down + * 1 = CPU (still) up + * 2 = CPU requested to be up before it had a chance + * to actually make itself down. + * Any other value is a bug. + */ + BUG_ON(mcpm_cpu_use_count[cluster][cpu] != 1 && + mcpm_cpu_use_count[cluster][cpu] != 2); + + if (cluster_is_down) + ret = platform_ops->cluster_powerup(cluster); + if (cpu_is_down && !ret) + ret = platform_ops->cpu_powerup(cpu, cluster); + + arch_spin_unlock(&mcpm_lock); + local_irq_enable(); + return ret; } typedef void (*phys_reset_t)(unsigned long); void mcpm_cpu_power_down(void) { + unsigned int mpidr, cpu, cluster; + bool cpu_going_down, last_man; phys_reset_t phys_reset; - if (WARN_ON_ONCE(!platform_ops || !platform_ops->power_down)) - return; + if (WARN_ON_ONCE(!platform_ops)) + return; BUG_ON(!irqs_disabled()); /* @@ -79,28 +138,65 @@ void mcpm_cpu_power_down(void) */ setup_mm_for_reboot(); - platform_ops->power_down(); + /* backward compatibility callback */ + if (platform_ops->power_down) { + platform_ops->power_down(); + goto not_dead; + } + mpidr = read_cpuid_mpidr(); + cpu = MPIDR_AFFINITY_LEVEL(mpidr, 0); + cluster = MPIDR_AFFINITY_LEVEL(mpidr, 1); + pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster); + + __mcpm_cpu_going_down(cpu, cluster); + + arch_spin_lock(&mcpm_lock); + BUG_ON(__mcpm_cluster_state(cluster) != CLUSTER_UP); + + mcpm_cpu_use_count[cluster][cpu]--; + BUG_ON(mcpm_cpu_use_count[cluster][cpu] != 0 && + mcpm_cpu_use_count[cluster][cpu] != 1); + cpu_going_down = !mcpm_cpu_use_count[cluster][cpu]; + last_man = mcpm_cluster_unused(cluster); + + if (last_man && __mcpm_outbound_enter_critical(cpu, cluster)) { + platform_ops->cpu_powerdown_prepare(cpu, cluster); + platform_ops->cluster_powerdown_prepare(cluster); + arch_spin_unlock(&mcpm_lock); + platform_ops->cluster_cache_disable(); + __mcpm_outbound_leave_critical(cluster, CLUSTER_DOWN); + } else { + if (cpu_going_down) + platform_ops->cpu_powerdown_prepare(cpu, cluster); + arch_spin_unlock(&mcpm_lock); + /* + * If cpu_going_down is false here, that means a power_up + * request raced ahead of us. Even if we do not want to + * shut this CPU down, the caller still expects execution + * to return through the system resume entry path, like + * when the WFI is aborted due to a new IRQ or the like.. + * So let's continue with cache cleaning in all cases. + */ + platform_ops->cpu_cache_disable(); + } + + __mcpm_cpu_down(cpu, cluster); + + /* Now we are prepared for power-down, do it: */ + if (cpu_going_down) + wfi(); + +not_dead: /* * It is possible for a power_up request to happen concurrently * with a power_down request for the same CPU. In this case the - * power_down method might not be able to actually enter a - * powered down state with the WFI instruction if the power_up - * method has removed the required reset condition. The - * power_down method is then allowed to return. We must perform - * a re-entry in the kernel as if the power_up method just had - * deasserted reset on the CPU. - * - * To simplify race issues, the platform specific implementation - * must accommodate for the possibility of unordered calls to - * power_down and power_up with a usage count. Therefore, if a - * call to power_up is issued for a CPU that is not down, then - * the next call to power_down must not attempt a full shutdown - * but only do the minimum (normally disabling L1 cache and CPU - * coherency) and return just as if a concurrent power_up request - * had happened as described above. + * CPU might not be able to actually enter a powered down state + * with the WFI instruction if the power_up request has removed + * the required reset condition. We must perform a re-entry in + * the kernel as if the power_up method just had deasserted reset + * on the CPU. */ - phys_reset = (phys_reset_t)(unsigned long)virt_to_phys(cpu_reset); phys_reset(virt_to_phys(mcpm_entry_point)); @@ -125,26 +221,66 @@ int mcpm_wait_for_cpu_powerdown(unsigned int cpu, unsigned int cluster) void mcpm_cpu_suspend(u64 expected_residency) { - phys_reset_t phys_reset; - - if (WARN_ON_ONCE(!platform_ops || !platform_ops->suspend)) + if (WARN_ON_ONCE(!platform_ops)) return; - BUG_ON(!irqs_disabled()); - /* Very similar to mcpm_cpu_power_down() */ - setup_mm_for_reboot(); - platform_ops->suspend(expected_residency); - phys_reset = (phys_reset_t)(unsigned long)virt_to_phys(cpu_reset); - phys_reset(virt_to_phys(mcpm_entry_point)); - BUG(); + /* backward compatibility callback */ + if (platform_ops->suspend) { + phys_reset_t phys_reset; + BUG_ON(!irqs_disabled()); + setup_mm_for_reboot(); + platform_ops->suspend(expected_residency); + phys_reset = (phys_reset_t)(unsigned long)virt_to_phys(cpu_reset); + phys_reset(virt_to_phys(mcpm_entry_point)); + BUG(); + } + + /* Some platforms might have to enable special resume modes, etc. */ + if (platform_ops->cpu_suspend_prepare) { + unsigned int mpidr = read_cpuid_mpidr(); + unsigned int cpu = MPIDR_AFFINITY_LEVEL(mpidr, 0); + unsigned int cluster = MPIDR_AFFINITY_LEVEL(mpidr, 1); + arch_spin_lock(&mcpm_lock); + platform_ops->cpu_suspend_prepare(cpu, cluster); + arch_spin_unlock(&mcpm_lock); + } + mcpm_cpu_power_down(); } int mcpm_cpu_powered_up(void) { + unsigned int mpidr, cpu, cluster; + bool cpu_was_down, first_man; + unsigned long flags; + if (!platform_ops) return -EUNATCH; - if (platform_ops->powered_up) + + /* backward compatibility callback */ + if (platform_ops->powered_up) { platform_ops->powered_up(); + return 0; + } + + mpidr = read_cpuid_mpidr(); + cpu = MPIDR_AFFINITY_LEVEL(mpidr, 0); + cluster = MPIDR_AFFINITY_LEVEL(mpidr, 1); + local_irq_save(flags); + arch_spin_lock(&mcpm_lock); + + cpu_was_down = !mcpm_cpu_use_count[cluster][cpu]; + first_man = mcpm_cluster_unused(cluster); + + if (first_man && platform_ops->cluster_is_up) + platform_ops->cluster_is_up(cluster); + if (cpu_was_down) + mcpm_cpu_use_count[cluster][cpu] = 1; + if (platform_ops->cpu_is_up) + platform_ops->cpu_is_up(cpu, cluster); + + arch_spin_unlock(&mcpm_lock); + local_irq_restore(flags); + return 0; } @@ -334,8 +470,10 @@ int __init mcpm_sync_init( } mpidr = read_cpuid_mpidr(); this_cluster = MPIDR_AFFINITY_LEVEL(mpidr, 1); - for_each_online_cpu(i) + for_each_online_cpu(i) { + mcpm_cpu_use_count[this_cluster][i] = 1; mcpm_sync.clusters[this_cluster].cpus[i].cpu = CPU_UP; + } mcpm_sync.clusters[this_cluster].cluster = CLUSTER_UP; sync_cache_w(&mcpm_sync); diff --git a/arch/arm/configs/ape6evm_defconfig b/arch/arm/configs/ape6evm_defconfig deleted file mode 100644 index 9e9a72e3d30f..000000000000 --- a/arch/arm/configs/ape6evm_defconfig +++ /dev/null @@ -1,109 +0,0 @@ -CONFIG_SYSVIPC=y -CONFIG_POSIX_MQUEUE=y -CONFIG_NO_HZ=y -CONFIG_HIGH_RES_TIMERS=y -CONFIG_BSD_PROCESS_ACCT=y -CONFIG_IKCONFIG=y -CONFIG_IKCONFIG_PROC=y -CONFIG_LOG_BUF_SHIFT=16 -CONFIG_CGROUPS=y -CONFIG_CGROUP_SCHED=y -CONFIG_KALLSYMS_ALL=y -CONFIG_EMBEDDED=y -CONFIG_PERF_EVENTS=y -CONFIG_SLAB=y -CONFIG_ARCH_SHMOBILE_LEGACY=y -CONFIG_ARCH_R8A73A4=y -CONFIG_MACH_APE6EVM=y -# CONFIG_ARM_THUMB is not set -CONFIG_CPU_BPREDICT_DISABLE=y -CONFIG_PL310_ERRATA_588369=y -CONFIG_ARM_ERRATA_754322=y -CONFIG_SMP=y -CONFIG_SCHED_MC=y -CONFIG_HAVE_ARM_ARCH_TIMER=y -CONFIG_NR_CPUS=8 -CONFIG_AEABI=y -CONFIG_HIGHMEM=y -CONFIG_HIGHPTE=y -# CONFIG_HW_PERF_EVENTS is not set -# CONFIG_COMPACTION is not set -# CONFIG_CROSS_MEMORY_ATTACH is not set -CONFIG_ARM_APPENDED_DTB=y -CONFIG_VFP=y -CONFIG_NEON=y -CONFIG_BINFMT_MISC=y -CONFIG_PM=y -CONFIG_NET=y -CONFIG_PACKET=y -CONFIG_UNIX=y -CONFIG_XFRM_USER=y -CONFIG_NET_KEY=y -CONFIG_NET_KEY_MIGRATE=y -CONFIG_INET=y -CONFIG_IP_MULTICAST=y -CONFIG_IP_PNP=y -CONFIG_IP_PNP_DHCP=y -# CONFIG_INET_LRO is not set -# CONFIG_IPV6_SIT is not set -CONFIG_NETFILTER=y -CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" -CONFIG_DEVTMPFS=y -CONFIG_DEVTMPFS_MOUNT=y -# CONFIG_FW_LOADER_USER_HELPER is not set -CONFIG_NETDEVICES=y -# CONFIG_NET_CADENCE is not set -CONFIG_SMC91X=y -CONFIG_SMSC911X=y -# CONFIG_INPUT_MOUSEDEV is not set -CONFIG_INPUT_EVDEV=y -CONFIG_KEYBOARD_GPIO=y -# CONFIG_INPUT_MOUSE is not set -# CONFIG_SERIO is not set -CONFIG_SERIAL_NONSTANDARD=y -CONFIG_SERIAL_SH_SCI=y -CONFIG_SERIAL_SH_SCI_NR_UARTS=12 -CONFIG_SERIAL_SH_SCI_CONSOLE=y -CONFIG_I2C=y -CONFIG_I2C_SH_MOBILE=y -CONFIG_GPIO_SH_PFC=y -CONFIG_GPIOLIB=y -# CONFIG_HWMON is not set -CONFIG_THERMAL=y -CONFIG_RCAR_THERMAL=y -CONFIG_REGULATOR=y -CONFIG_REGULATOR_FIXED_VOLTAGE=y -CONFIG_REGULATOR_GPIO=y -CONFIG_REGULATOR_MAX8973=y -# CONFIG_HID is not set -# CONFIG_USB_SUPPORT is not set -CONFIG_MMC=y -CONFIG_MMC_SDHI=y -CONFIG_MMC_SH_MMCIF=y -CONFIG_NEW_LEDS=y -CONFIG_LEDS_CLASS=y -CONFIG_LEDS_GPIO=y -CONFIG_DMADEVICES=y -CONFIG_SH_DMAE=y -# CONFIG_IOMMU_SUPPORT is not set -# CONFIG_DNOTIFY is not set -CONFIG_TMPFS=y -# CONFIG_MISC_FILESYSTEMS is not set -CONFIG_NFS_FS=y -CONFIG_NFS_V3_ACL=y -CONFIG_NFS_V4=y -CONFIG_NFS_V4_1=y -CONFIG_ROOT_NFS=y -CONFIG_MAGIC_SYSRQ=y -CONFIG_ENABLE_DEFAULT_TRACERS=y -CONFIG_CRYPTO_CBC=y -CONFIG_CRYPTO_ECB=y -CONFIG_CRYPTO_MD5=y -CONFIG_CRYPTO_MICHAEL_MIC=y -CONFIG_CRYPTO_TWOFISH=y -CONFIG_CRC_CCITT=y -CONFIG_CRC16=y -CONFIG_CRC_T10DIF=y -CONFIG_CRC_ITU_T=y -CONFIG_CRC7=y -CONFIG_LIBCRC32C=y diff --git a/arch/arm/configs/at91_dt_defconfig b/arch/arm/configs/at91_dt_defconfig index 811e72bbe642..bcef49a21801 100644 --- a/arch/arm/configs/at91_dt_defconfig +++ b/arch/arm/configs/at91_dt_defconfig @@ -13,10 +13,13 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_BLK_DEV_BSG is not set # CONFIG_IOSCHED_DEADLINE is not set # CONFIG_IOSCHED_CFQ is not set +CONFIG_ARCH_MULTI_V4T=y +CONFIG_ARCH_MULTI_V5=y +# CONFIG_ARCH_MULTI_V7 is not set CONFIG_ARCH_AT91=y +CONFIG_SOC_SAM_V4_V5=y CONFIG_SOC_AT91RM9200=y CONFIG_SOC_AT91SAM9=y -CONFIG_AT91_TIMER_HZ=128 CONFIG_AEABI=y CONFIG_UACCESS_WITH_MEMCPY=y CONFIG_ZBOOT_ROM_TEXT=0x0 diff --git a/arch/arm/configs/exynos_defconfig b/arch/arm/configs/exynos_defconfig index 1d8935359fd0..d034c96c039b 100644 --- a/arch/arm/configs/exynos_defconfig +++ b/arch/arm/configs/exynos_defconfig @@ -26,6 +26,8 @@ CONFIG_ZBOOT_ROM_BSS=0x0 CONFIG_ARM_APPENDED_DTB=y CONFIG_ARM_ATAG_DTB_COMPAT=y CONFIG_CMDLINE="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC1,115200 init=/linuxrc mem=256M" +CONFIG_CPU_IDLE=y +CONFIG_ARM_EXYNOS_CPUIDLE=y CONFIG_VFP=y CONFIG_NEON=y CONFIG_PM=y @@ -34,6 +36,14 @@ CONFIG_PACKET=y CONFIG_UNIX=y CONFIG_NET_KEY=y CONFIG_INET=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +CONFIG_WIRELESS=y +CONFIG_CFG80211=y +CONFIG_MWIFIEX=y +CONFIG_MWIFIEX_SDIO=y CONFIG_RFKILL_REGULATOR=y CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_DEVTMPFS=y @@ -91,9 +101,11 @@ CONFIG_CHARGER_MAX77693=y CONFIG_CHARGER_TPS65090=y CONFIG_HWMON=y CONFIG_SENSORS_LM90=y +CONFIG_CPU_FREQ=y +CONFIG_CPU_THERMAL=y CONFIG_THERMAL=y CONFIG_EXYNOS_THERMAL=y -CONFIG_EXYNOS_THERMAL_CORE=y +CONFIG_THERMAL_EMULATION=y CONFIG_WATCHDOG=y CONFIG_S3C2410_WATCHDOG=y CONFIG_MFD_CROS_EC=y @@ -118,6 +130,7 @@ CONFIG_REGULATOR_S2MPS11=y CONFIG_REGULATOR_S5M8767=y CONFIG_REGULATOR_TPS65090=y CONFIG_DRM=y +CONFIG_DRM_EXYNOS_HDMI=y CONFIG_DRM_BRIDGE=y CONFIG_DRM_PTN3460=y CONFIG_DRM_PS8622=y @@ -171,10 +184,11 @@ CONFIG_RTC_DRV_S5M=y CONFIG_RTC_DRV_S3C=y CONFIG_DMADEVICES=y CONFIG_PL330_DMA=y +CONFIG_CHROME_PLATFORMS=y +CONFIG_CROS_EC_CHARDEV=y CONFIG_COMMON_CLK_MAX77686=y CONFIG_COMMON_CLK_MAX77802=y CONFIG_COMMON_CLK_S2MPS11=y -CONFIG_EXYNOS_IOMMU=y CONFIG_EXTCON=y CONFIG_EXTCON_MAX14577=y CONFIG_EXTCON_MAX77693=y @@ -197,6 +211,8 @@ CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y CONFIG_CRAMFS=y CONFIG_ROMFS_FS=y +CONFIG_NFS_FS=y +CONFIG_ROOT_NFS=y CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ASCII=y CONFIG_NLS_ISO8859_1=y diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig index e6b0007355f8..d3a8018639de 100644 --- a/arch/arm/configs/imx_v4_v5_defconfig +++ b/arch/arm/configs/imx_v4_v5_defconfig @@ -24,9 +24,8 @@ CONFIG_ARCH_MXC=y CONFIG_MACH_SCB9328=y CONFIG_MACH_APF9328=y CONFIG_MACH_MX21ADS=y -CONFIG_MACH_MX25_3DS=y CONFIG_MACH_EUKREA_CPUIMX25SD=y -CONFIG_MACH_IMX25_DT=y +CONFIG_SOC_IMX25=y CONFIG_MACH_MX27ADS=y CONFIG_MACH_MX27_3DS=y CONFIG_MACH_IMX27_VISSTRIM_M10=y @@ -177,6 +176,7 @@ CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y CONFIG_EXT4_FS=y # CONFIG_DNOTIFY is not set +CONFIG_VFAT_FS=y # CONFIG_PROC_PAGE_MONITOR is not set CONFIG_TMPFS=y CONFIG_JFFS2_FS=y diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig index cf1e71e2f60a..fdeb1c83dcb5 100644 --- a/arch/arm/configs/imx_v6_v7_defconfig +++ b/arch/arm/configs/imx_v6_v7_defconfig @@ -71,6 +71,9 @@ CONFIG_IPV6=y CONFIG_NETFILTER=y CONFIG_CAN=y CONFIG_CAN_FLEXCAN=y +CONFIG_BT=y +CONFIG_BT_HCIUART=y +CONFIG_BT_HCIUART_3WIRE=y CONFIG_CFG80211=y CONFIG_MAC80211=y CONFIG_RFKILL=y @@ -168,6 +171,7 @@ CONFIG_SPI=y CONFIG_SPI_IMX=y CONFIG_GPIO_SYSFS=y CONFIG_GPIO_MC9S08DZ60=y +CONFIG_GPIO_PCA953X=y CONFIG_GPIO_STMPE=y CONFIG_POWER_SUPPLY=y CONFIG_POWER_RESET=y diff --git a/arch/arm/configs/mackerel_defconfig b/arch/arm/configs/mackerel_defconfig deleted file mode 100644 index 05a529311b4d..000000000000 --- a/arch/arm/configs/mackerel_defconfig +++ /dev/null @@ -1,157 +0,0 @@ -CONFIG_EXPERIMENTAL=y -CONFIG_SYSVIPC=y -CONFIG_IKCONFIG=y -CONFIG_IKCONFIG_PROC=y -CONFIG_LOG_BUF_SHIFT=16 -# CONFIG_UTS_NS is not set -# CONFIG_IPC_NS is not set -# CONFIG_USER_NS is not set -# CONFIG_PID_NS is not set -# CONFIG_NET_NS is not set -CONFIG_SLAB=y -CONFIG_MODULES=y -CONFIG_MODULE_UNLOAD=y -# CONFIG_BLK_DEV_BSG is not set -# CONFIG_IOSCHED_DEADLINE is not set -# CONFIG_IOSCHED_CFQ is not set -CONFIG_ARCH_SHMOBILE_LEGACY=y -CONFIG_ARCH_SH7372=y -CONFIG_MACH_MACKEREL=y -CONFIG_MEMORY_SIZE=0x10000000 -CONFIG_AEABI=y -# CONFIG_OABI_COMPAT is not set -CONFIG_FORCE_MAX_ZONEORDER=15 -CONFIG_ZBOOT_ROM_TEXT=0x0 -CONFIG_ZBOOT_ROM_BSS=0x0 -CONFIG_ARM_APPENDED_DTB=y -CONFIG_KEXEC=y -CONFIG_VFP=y -# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set -CONFIG_PM=y -CONFIG_NET=y -CONFIG_PACKET=y -CONFIG_UNIX=y -CONFIG_INET=y -CONFIG_IP_MULTICAST=y -CONFIG_IP_PNP=y -CONFIG_IP_PNP_DHCP=y -# CONFIG_INET_XFRM_MODE_TRANSPORT is not set -# CONFIG_INET_XFRM_MODE_TUNNEL is not set -# CONFIG_INET_XFRM_MODE_BEET is not set -# CONFIG_IPV6 is not set -# CONFIG_WIRELESS is not set -CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" -CONFIG_DEVTMPFS=y -CONFIG_DEVTMPFS_MOUNT=y -# CONFIG_FIRMWARE_IN_KERNEL is not set -CONFIG_MTD=y -CONFIG_MTD_CONCAT=y -CONFIG_MTD_PARTITIONS=y -CONFIG_MTD_CHAR=y -CONFIG_MTD_BLOCK=y -CONFIG_MTD_CFI=y -CONFIG_MTD_CFI_ADV_OPTIONS=y -CONFIG_MTD_CFI_INTELEXT=y -CONFIG_MTD_PHYSMAP=y -CONFIG_MTD_ARM_INTEGRATOR=y -CONFIG_MTD_BLOCK2MTD=y -CONFIG_SCSI=y -CONFIG_BLK_DEV_SD=y -# CONFIG_SCSI_LOWLEVEL is not set -CONFIG_NETDEVICES=y -CONFIG_NET_ETHERNET=y -CONFIG_SMSC911X=y -# CONFIG_NETDEV_1000 is not set -# CONFIG_NETDEV_10000 is not set -# CONFIG_WLAN is not set -# CONFIG_INPUT_MOUSEDEV_PSAUX is not set -# CONFIG_INPUT_KEYBOARD is not set -# CONFIG_INPUT_MOUSE is not set -CONFIG_SERIAL_SH_SCI=y -CONFIG_SERIAL_SH_SCI_NR_UARTS=8 -CONFIG_SERIAL_SH_SCI_CONSOLE=y -# CONFIG_LEGACY_PTYS is not set -# CONFIG_HW_RANDOM is not set -CONFIG_I2C=y -CONFIG_I2C_SH_MOBILE=y -# CONFIG_HWMON is not set -# CONFIG_MFD_SUPPORT is not set -CONFIG_REGULATOR=y -CONFIG_FB=y -CONFIG_FB_MODE_HELPERS=y -CONFIG_FB_SH_MOBILE_LCDC=y -CONFIG_FB_SH_MOBILE_HDMI=y -CONFIG_FRAMEBUFFER_CONSOLE=y -CONFIG_LOGO=y -# CONFIG_LOGO_LINUX_MONO is not set -# CONFIG_LOGO_LINUX_CLUT224 is not set -# CONFIG_SND_SUPPORT_OLD_API is not set -# CONFIG_SND_VERBOSE_PROCFS is not set -# CONFIG_SND_DRIVERS is not set -# CONFIG_SND_ARM is not set -CONFIG_SND_SOC_SH4_FSI=y -CONFIG_USB=y -CONFIG_USB_RENESAS_USBHS_HCD=y -CONFIG_USB_RENESAS_USBHS=y -CONFIG_USB_STORAGE=y -CONFIG_USB_GADGET=y -CONFIG_USB_RENESAS_USBHS_UDC=y -CONFIG_MMC=y -CONFIG_MMC_SDHI=y -CONFIG_MMC_SH_MMCIF=y -CONFIG_DMADEVICES=y -CONFIG_SH_DMAE=y -CONFIG_EXT2_FS=y -CONFIG_EXT2_FS_XATTR=y -CONFIG_EXT2_FS_POSIX_ACL=y -CONFIG_EXT2_FS_SECURITY=y -CONFIG_EXT2_FS_XIP=y -CONFIG_EXT3_FS=y -# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set -CONFIG_EXT3_FS_POSIX_ACL=y -CONFIG_EXT3_FS_SECURITY=y -# CONFIG_DNOTIFY is not set -CONFIG_MSDOS_FS=y -CONFIG_VFAT_FS=y -CONFIG_TMPFS=y -# CONFIG_MISC_FILESYSTEMS is not set -CONFIG_NFS_FS=y -CONFIG_NFS_V3=y -CONFIG_NFS_V3_ACL=y -CONFIG_NFS_V4=y -CONFIG_NFS_V4_1=y -CONFIG_ROOT_NFS=y -CONFIG_NLS_CODEPAGE_437=y -CONFIG_NLS_CODEPAGE_737=y -CONFIG_NLS_CODEPAGE_775=y -CONFIG_NLS_CODEPAGE_850=y -CONFIG_NLS_CODEPAGE_852=y -CONFIG_NLS_CODEPAGE_855=y -CONFIG_NLS_CODEPAGE_857=y -CONFIG_NLS_CODEPAGE_860=y -CONFIG_NLS_CODEPAGE_861=y -CONFIG_NLS_CODEPAGE_862=y -CONFIG_NLS_CODEPAGE_863=y -CONFIG_NLS_CODEPAGE_864=y -CONFIG_NLS_CODEPAGE_865=y -CONFIG_NLS_CODEPAGE_866=y -CONFIG_NLS_CODEPAGE_869=y -CONFIG_NLS_ISO8859_1=y -CONFIG_NLS_ISO8859_2=y -CONFIG_NLS_ISO8859_3=y -CONFIG_NLS_ISO8859_4=y -CONFIG_NLS_ISO8859_5=y -CONFIG_NLS_ISO8859_6=y -CONFIG_NLS_ISO8859_7=y -CONFIG_NLS_ISO8859_9=y -CONFIG_NLS_ISO8859_13=y -CONFIG_NLS_ISO8859_14=y -CONFIG_NLS_ISO8859_15=y -CONFIG_NLS_KOI8_R=y -CONFIG_NLS_KOI8_U=y -CONFIG_NLS_UTF8=y -# CONFIG_ENABLE_WARN_DEPRECATED is not set -# CONFIG_ENABLE_MUST_CHECK is not set -# CONFIG_ARM_UNWIND is not set -CONFIG_CRYPTO=y -CONFIG_CRYPTO_ANSI_CPRNG=y diff --git a/arch/arm/configs/msm_defconfig b/arch/arm/configs/msm_defconfig deleted file mode 100644 index dd18c9e527d6..000000000000 --- a/arch/arm/configs/msm_defconfig +++ /dev/null @@ -1,121 +0,0 @@ -CONFIG_SYSVIPC=y -CONFIG_NO_HZ=y -CONFIG_HIGH_RES_TIMERS=y -CONFIG_IKCONFIG=y -CONFIG_IKCONFIG_PROC=y -CONFIG_BLK_DEV_INITRD=y -CONFIG_SYSCTL_SYSCALL=y -CONFIG_KALLSYMS_ALL=y -CONFIG_EMBEDDED=y -# CONFIG_SLUB_DEBUG is not set -# CONFIG_COMPAT_BRK is not set -CONFIG_PROFILING=y -CONFIG_OPROFILE=y -CONFIG_KPROBES=y -CONFIG_MODULES=y -CONFIG_MODULE_UNLOAD=y -CONFIG_MODULE_FORCE_UNLOAD=y -CONFIG_MODVERSIONS=y -CONFIG_PARTITION_ADVANCED=y -CONFIG_ARCH_MSM=y -CONFIG_PREEMPT=y -CONFIG_AEABI=y -CONFIG_HIGHMEM=y -CONFIG_HIGHPTE=y -CONFIG_CLEANCACHE=y -CONFIG_AUTO_ZRELADDR=y -CONFIG_VFP=y -# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set -CONFIG_NET=y -CONFIG_PACKET=y -CONFIG_UNIX=y -CONFIG_INET=y -CONFIG_IP_ADVANCED_ROUTER=y -CONFIG_IP_MULTIPLE_TABLES=y -CONFIG_IP_ROUTE_VERBOSE=y -CONFIG_IP_PNP=y -CONFIG_IP_PNP_DHCP=y -# CONFIG_INET_XFRM_MODE_TRANSPORT is not set -# CONFIG_INET_XFRM_MODE_TUNNEL is not set -# CONFIG_INET_XFRM_MODE_BEET is not set -# CONFIG_INET_LRO is not set -# CONFIG_IPV6 is not set -CONFIG_CFG80211=y -CONFIG_RFKILL=y -CONFIG_BLK_DEV_LOOP=y -CONFIG_BLK_DEV_RAM=y -CONFIG_SCSI=y -CONFIG_BLK_DEV_SD=y -CONFIG_CHR_DEV_SG=y -CONFIG_CHR_DEV_SCH=y -CONFIG_SCSI_MULTI_LUN=y -CONFIG_SCSI_CONSTANTS=y -CONFIG_SCSI_LOGGING=y -CONFIG_SCSI_SCAN_ASYNC=y -CONFIG_NETDEVICES=y -CONFIG_DUMMY=y -CONFIG_SLIP=y -CONFIG_SLIP_COMPRESSED=y -CONFIG_SLIP_MODE_SLIP6=y -CONFIG_USB_USBNET=y -# CONFIG_USB_NET_AX8817X is not set -# CONFIG_USB_NET_ZAURUS is not set -CONFIG_INPUT_EVDEV=y -# CONFIG_KEYBOARD_ATKBD is not set -# CONFIG_MOUSE_PS2 is not set -CONFIG_INPUT_JOYSTICK=y -CONFIG_INPUT_TOUCHSCREEN=y -CONFIG_INPUT_MISC=y -CONFIG_INPUT_UINPUT=y -CONFIG_SERIO_LIBPS2=y -# CONFIG_LEGACY_PTYS is not set -CONFIG_SERIAL_MSM=y -CONFIG_SERIAL_MSM_CONSOLE=y -# CONFIG_HW_RANDOM is not set -CONFIG_I2C=y -CONFIG_I2C_CHARDEV=y -CONFIG_SPI=y -CONFIG_DEBUG_GPIO=y -CONFIG_GPIO_SYSFS=y -CONFIG_THERMAL=y -CONFIG_REGULATOR=y -CONFIG_MEDIA_SUPPORT=y -CONFIG_FB=y -CONFIG_SOUND=y -CONFIG_SND=y -CONFIG_SND_DYNAMIC_MINORS=y -# CONFIG_SND_ARM is not set -# CONFIG_SND_SPI is not set -# CONFIG_SND_USB is not set -CONFIG_SND_SOC=y -CONFIG_USB=y -CONFIG_USB_ANNOUNCE_NEW_DEVICES=y -CONFIG_USB_MON=y -CONFIG_USB_EHCI_HCD=y -CONFIG_USB_ACM=y -CONFIG_USB_SERIAL=y -CONFIG_USB_GADGET=y -CONFIG_USB_GADGET_DEBUG_FILES=y -CONFIG_USB_GADGET_VBUS_DRAW=500 -CONFIG_RTC_CLASS=y -CONFIG_STAGING=y -CONFIG_EXT2_FS=y -CONFIG_EXT2_FS_XATTR=y -CONFIG_EXT3_FS=y -# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set -CONFIG_EXT4_FS=y -CONFIG_FUSE_FS=y -CONFIG_VFAT_FS=y -CONFIG_TMPFS=y -CONFIG_NFS_FS=y -CONFIG_NFS_V3_ACL=y -CONFIG_NFS_V4=y -CONFIG_CIFS=y -CONFIG_PRINTK_TIME=y -CONFIG_DYNAMIC_DEBUG=y -CONFIG_DEBUG_INFO=y -CONFIG_MAGIC_SYSRQ=y -CONFIG_LOCKUP_DETECTOR=y -# CONFIG_DETECT_HUNG_TASK is not set -# CONFIG_SCHED_DEBUG is not set -CONFIG_TIMER_STATS=y diff --git a/arch/arm/configs/multi_v5_defconfig b/arch/arm/configs/multi_v5_defconfig index 9d56781a8f80..f69a459f4f92 100644 --- a/arch/arm/configs/multi_v5_defconfig +++ b/arch/arm/configs/multi_v5_defconfig @@ -13,7 +13,7 @@ CONFIG_ARCH_MVEBU=y CONFIG_MACH_KIRKWOOD=y CONFIG_MACH_NETXBIG=y CONFIG_ARCH_MXC=y -CONFIG_MACH_IMX25_DT=y +CONFIG_SOC_IMX25=y CONFIG_MACH_IMX27_DT=y CONFIG_ARCH_U300=y CONFIG_PCI_MVEBU=y diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig index 06075b6d2463..0ca4a3eaf65d 100644 --- a/arch/arm/configs/multi_v7_defconfig +++ b/arch/arm/configs/multi_v7_defconfig @@ -12,10 +12,12 @@ CONFIG_MODULE_UNLOAD=y CONFIG_PARTITION_ADVANCED=y CONFIG_CMDLINE_PARTITION=y CONFIG_ARCH_VIRT=y +CONFIG_ARCH_ALPINE=y CONFIG_ARCH_MVEBU=y CONFIG_MACH_ARMADA_370=y CONFIG_MACH_ARMADA_375=y CONFIG_MACH_ARMADA_38X=y +CONFIG_MACH_ARMADA_39X=y CONFIG_MACH_ARMADA_XP=y CONFIG_MACH_DOVE=y CONFIG_ARCH_BCM=y @@ -37,11 +39,14 @@ CONFIG_ARCH_HIP04=y CONFIG_ARCH_KEYSTONE=y CONFIG_ARCH_MESON=y CONFIG_ARCH_MXC=y +CONFIG_SOC_IMX50=y CONFIG_SOC_IMX51=y CONFIG_SOC_IMX53=y CONFIG_SOC_IMX6Q=y CONFIG_SOC_IMX6SL=y +CONFIG_SOC_IMX6SX=y CONFIG_SOC_VF610=y +CONFIG_SOC_LS1021A=y CONFIG_ARCH_OMAP3=y CONFIG_ARCH_OMAP4=y CONFIG_SOC_OMAP5=y @@ -91,6 +96,7 @@ CONFIG_ARCH_WM8850=y CONFIG_ARCH_ZYNQ=y CONFIG_TRUSTED_FOUNDATIONS=y CONFIG_PCI=y +CONFIG_PCI_HOST_GENERIC=y CONFIG_PCI_KEYSTONE=y CONFIG_PCI_MSI=y CONFIG_PCI_MVEBU=y @@ -133,6 +139,9 @@ CONFIG_CAN_BCM=y CONFIG_CAN_DEV=y CONFIG_CAN_XILINXCAN=y CONFIG_CAN_MCP251X=y +CONFIG_BT=m +CONFIG_BT_MRVL=m +CONFIG_BT_MRVL_SDIO=m CONFIG_CFG80211=m CONFIG_MAC80211=m CONFIG_RFKILL=y @@ -200,6 +209,8 @@ CONFIG_USB_NET_SMSC95XX=y CONFIG_BRCMFMAC=m CONFIG_RT2X00=m CONFIG_RT2800USB=m +CONFIG_MWIFIEX=m +CONFIG_MWIFIEX_SDIO=m CONFIG_INPUT_JOYDEV=y CONFIG_INPUT_EVDEV=y CONFIG_KEYBOARD_GPIO=y @@ -208,6 +219,7 @@ CONFIG_KEYBOARD_SPEAR=y CONFIG_KEYBOARD_ST_KEYSCAN=y CONFIG_KEYBOARD_CROS_EC=y CONFIG_MOUSE_PS2_ELANTECH=y +CONFIG_MOUSE_ELAN_I2C=y CONFIG_INPUT_TOUCHSCREEN=y CONFIG_TOUCHSCREEN_ATMEL_MXT=y CONFIG_TOUCHSCREEN_ST1232=m @@ -308,6 +320,7 @@ CONFIG_BATTERY_SBS=y CONFIG_CHARGER_TPS65090=y CONFIG_POWER_RESET_AS3722=y CONFIG_POWER_RESET_GPIO=y +CONFIG_POWER_RESET_GPIO_RESTART=y CONFIG_POWER_RESET_KEYSTONE=y CONFIG_POWER_RESET_SUN6I=y CONFIG_POWER_RESET_RMOBILE=y @@ -505,7 +518,6 @@ CONFIG_DW_DMAC=y CONFIG_MV_XOR=y CONFIG_TEGRA20_APB_DMA=y CONFIG_SH_DMAE=y -CONFIG_RCAR_AUDMAC_PP=m CONFIG_RCAR_DMAC=y CONFIG_STE_DMA40=y CONFIG_SIRF_DMA=y @@ -533,6 +545,8 @@ CONFIG_MSM_MMCC_8960=y CONFIG_MSM_MMCC_8974=y CONFIG_TEGRA_IOMMU_GART=y CONFIG_TEGRA_IOMMU_SMMU=y +CONFIG_PM_DEVFREQ=y +CONFIG_ARM_TEGRA_DEVFREQ=m CONFIG_MEMORY=y CONFIG_TI_AEMIF=y CONFIG_IIO=y @@ -550,6 +564,7 @@ CONFIG_PHY_MIPHY365X=y CONFIG_PHY_STIH41X_USB=y CONFIG_PHY_STIH407_USB=y CONFIG_PHY_SUN4I_USB=y +CONFIG_PHY_SUN9I_USB=y CONFIG_EXT4_FS=y CONFIG_AUTOFS4_FS=y CONFIG_MSDOS_FS=y diff --git a/arch/arm/configs/mvebu_v7_defconfig b/arch/arm/configs/mvebu_v7_defconfig index 73673e95f23c..cacc9f4055a7 100644 --- a/arch/arm/configs/mvebu_v7_defconfig +++ b/arch/arm/configs/mvebu_v7_defconfig @@ -5,6 +5,7 @@ CONFIG_HIGH_RES_TIMERS=y CONFIG_LOG_BUF_SHIFT=14 CONFIG_BLK_DEV_INITRD=y CONFIG_EXPERT=y +CONFIG_PERF_EVENTS=y CONFIG_SLAB=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y @@ -12,6 +13,7 @@ CONFIG_ARCH_MVEBU=y CONFIG_MACH_ARMADA_370=y CONFIG_MACH_ARMADA_375=y CONFIG_MACH_ARMADA_38X=y +CONFIG_MACH_ARMADA_39X=y CONFIG_MACH_ARMADA_XP=y CONFIG_MACH_DOVE=y CONFIG_PCI=y diff --git a/arch/arm/configs/mxs_defconfig b/arch/arm/configs/mxs_defconfig index c7906c2fd645..b47e7c6628c9 100644 --- a/arch/arm/configs/mxs_defconfig +++ b/arch/arm/configs/mxs_defconfig @@ -149,6 +149,7 @@ CONFIG_EXT4_FS=y CONFIG_FSCACHE=m CONFIG_FSCACHE_STATS=y CONFIG_CACHEFILES=m +CONFIG_VFAT_FS=y CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y CONFIG_JFFS2_FS=y diff --git a/arch/arm/configs/omap1_defconfig b/arch/arm/configs/omap1_defconfig index a7dce674f1be..0c8a78734536 100644 --- a/arch/arm/configs/omap1_defconfig +++ b/arch/arm/configs/omap1_defconfig @@ -1,4 +1,3 @@ -CONFIG_EXPERIMENTAL=y # CONFIG_SWAP is not set CONFIG_SYSVIPC=y CONFIG_POSIX_MQUEUE=y @@ -34,7 +33,6 @@ CONFIG_ARCH_OMAP16XX=y CONFIG_MACH_OMAP_INNOVATOR=y CONFIG_MACH_OMAP_H2=y CONFIG_MACH_OMAP_H3=y -CONFIG_MACH_OMAP_HTCWIZARD=y CONFIG_MACH_HERALD=y CONFIG_MACH_OMAP_OSK=y CONFIG_MACH_OMAP_PERSEUS2=y @@ -55,7 +53,6 @@ CONFIG_HIGH_RES_TIMERS=y CONFIG_PREEMPT=y CONFIG_AEABI=y CONFIG_LEDS=y -CONFIG_LEDS_CPU=y CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 CONFIG_CMDLINE="root=1f03 rootfstype=jffs2" @@ -80,8 +77,6 @@ CONFIG_IP_PNP_BOOTP=y CONFIG_IPV6=y CONFIG_NETFILTER=y CONFIG_BT=y -CONFIG_BT_L2CAP=y -CONFIG_BT_SCO=y CONFIG_BT_RFCOMM=y CONFIG_BT_RFCOMM_TTY=y CONFIG_BT_BNEP=y @@ -92,11 +87,7 @@ CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_CONNECTOR=y # CONFIG_PROC_EVENTS is not set CONFIG_MTD=y -CONFIG_MTD_DEBUG=y -CONFIG_MTD_DEBUG_VERBOSE=3 -CONFIG_MTD_PARTITIONS=y CONFIG_MTD_CMDLINE_PARTS=y -CONFIG_MTD_CHAR=y CONFIG_MTD_BLOCK=y CONFIG_MTD_CFI=y CONFIG_MTD_CFI_INTELEXT=y @@ -113,11 +104,9 @@ CONFIG_BLK_DEV_SD=y CONFIG_CHR_DEV_ST=y CONFIG_BLK_DEV_SR=y CONFIG_CHR_DEV_SG=y -CONFIG_SCSI_MULTI_LUN=y CONFIG_NETDEVICES=y CONFIG_TUN=y CONFIG_PHYLIB=y -CONFIG_NET_ETHERNET=y CONFIG_SMC91X=y CONFIG_USB_CATC=y CONFIG_USB_KAWETH=y @@ -158,7 +147,6 @@ CONFIG_SPI_OMAP_UWIRE=y CONFIG_WATCHDOG=y CONFIG_WATCHDOG_NOWAYOUT=y CONFIG_OMAP_WATCHDOG=y -CONFIG_VIDEO_OUTPUT_CONTROL=y CONFIG_FB=y CONFIG_FIRMWARE_EDID=y CONFIG_FB_MODE_HELPERS=y @@ -168,7 +156,6 @@ CONFIG_FB_OMAP_LCDC_EXTERNAL=y CONFIG_FB_OMAP_LCDC_HWA742=y CONFIG_FB_OMAP_MANUAL_UPDATE=y CONFIG_FB_OMAP_LCD_MIPID=y -CONFIG_FB_OMAP_BOOTLOADER_INIT=y CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_LCD_CLASS_DEVICE=y CONFIG_FRAMEBUFFER_CONSOLE=y @@ -194,7 +181,6 @@ CONFIG_SND_OMAP_SOC=y # CONFIG_USB_HID is not set CONFIG_USB=y CONFIG_USB_PHY=y -# CONFIG_USB_DEVICE_CLASS is not set CONFIG_USB_MON=y CONFIG_USB_OHCI_HCD=y CONFIG_USB_STORAGE=y @@ -261,9 +247,7 @@ CONFIG_DEBUG_SPINLOCK=y CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_BUGVERBOSE is not set CONFIG_DEBUG_INFO=y -# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_DEBUG_USER=y -CONFIG_DEBUG_ERRORS=y CONFIG_SECURITY=y CONFIG_CRYPTO_ECB=y CONFIG_CRYPTO_PCBC=y diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index 8e108599e1af..3743ca221d40 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -1,3 +1,4 @@ +CONFIG_KERNEL_LZMA=y CONFIG_SYSVIPC=y CONFIG_POSIX_MQUEUE=y CONFIG_FHANDLE=y @@ -86,17 +87,33 @@ CONFIG_IP_PNP_BOOTP=y CONFIG_IP_PNP_RARP=y # CONFIG_INET_LRO is not set CONFIG_NETFILTER=y +CONFIG_PHONET=m CONFIG_CAN=m CONFIG_CAN_C_CAN=m CONFIG_CAN_C_CAN_PLATFORM=m CONFIG_BT=m +CONFIG_BT_RFCOMM=m +CONFIG_BT_RFCOMM_TTY=y +CONFIG_BT_BNEP=m +CONFIG_BT_BNEP_MC_FILTER=y +CONFIG_BT_BNEP_PROTO_FILTER=y +CONFIG_BT_HIDP=m +CONFIG_BT_HCIBTUSB=m +CONFIG_BT_HCIBTSDIO=m CONFIG_BT_HCIUART=m CONFIG_BT_HCIUART_H4=y CONFIG_BT_HCIUART_BCSP=y CONFIG_BT_HCIUART_LL=y +CONFIG_BT_HCIUART_3WIRE=y CONFIG_BT_HCIBCM203X=m CONFIG_BT_HCIBPA10X=m CONFIG_CFG80211=m +CONFIG_BT_HCIBFUSB=m +CONFIG_BT_HCIVHCI=m +CONFIG_BT_MRVL=m +CONFIG_BT_MRVL_SDIO=m +CONFIG_AF_RXRPC=m +CONFIG_RXKAD=m CONFIG_MAC80211=m CONFIG_DEVTMPFS=y CONFIG_DEVTMPFS_MOUNT=y @@ -163,6 +180,7 @@ CONFIG_USB_EPSON2888=y CONFIG_USB_EHCI_HCD=m CONFIG_USB_OHCI_HCD=m CONFIG_USB_KC2190=y +CONFIG_USB_CDC_PHONET=m CONFIG_LIBERTAS=m CONFIG_LIBERTAS_USB=m CONFIG_LIBERTAS_SDIO=m @@ -209,6 +227,10 @@ CONFIG_I2C_CHARDEV=y CONFIG_SPI=y CONFIG_SPI_OMAP24XX=y CONFIG_SPI_TI_QSPI=m +CONFIG_HSI=m +CONFIG_OMAP_SSI=m +CONFIG_NOKIA_MODEM=m +CONFIG_SSI_PROTOCOL=m CONFIG_PINCTRL_SINGLE=y CONFIG_DEBUG_GPIO=y CONFIG_GPIO_SYSFS=y @@ -334,6 +356,7 @@ CONFIG_USB_CONFIGFS_ECM=y CONFIG_USB_CONFIGFS_ECM_SUBSET=y CONFIG_USB_CONFIGFS_RNDIS=y CONFIG_USB_CONFIGFS_EEM=y +CONFIG_USB_CONFIGFS_PHONET=y CONFIG_USB_CONFIGFS_MASS_STORAGE=y CONFIG_USB_CONFIGFS_F_LB_SS=y CONFIG_USB_CONFIGFS_F_FS=y @@ -342,6 +365,7 @@ CONFIG_USB_CONFIGFS_F_UAC2=y CONFIG_USB_CONFIGFS_F_MIDI=y CONFIG_USB_CONFIGFS_F_HID=y CONFIG_USB_ZERO=m +CONFIG_USB_G_NOKIA=m CONFIG_MMC=y CONFIG_SDIO_UART=y CONFIG_MMC_OMAP=y @@ -349,6 +373,7 @@ CONFIG_MMC_OMAP_HS=y CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=m CONFIG_LEDS_GPIO=m +CONFIG_LEDS_PWM=m CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=m CONFIG_LEDS_TRIGGER_ONESHOT=m @@ -368,6 +393,7 @@ CONFIG_TI_EDMA=y CONFIG_DMA_OMAP=y # CONFIG_IOMMU_SUPPORT is not set CONFIG_EXTCON=m +CONFIG_EXTCON_USB_GPIO=m CONFIG_EXTCON_PALMAS=m CONFIG_TI_EMIF=m CONFIG_PWM=y @@ -390,6 +416,7 @@ CONFIG_MSDOS_FS=y CONFIG_VFAT_FS=y CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y +CONFIG_CONFIGFS_FS=y CONFIG_JFFS2_FS=y CONFIG_JFFS2_SUMMARY=y CONFIG_JFFS2_FS_XATTR=y diff --git a/arch/arm/configs/qcom_defconfig b/arch/arm/configs/qcom_defconfig index 8c7da3319d82..d2f2babfd47a 100644 --- a/arch/arm/configs/qcom_defconfig +++ b/arch/arm/configs/qcom_defconfig @@ -97,9 +97,9 @@ CONFIG_PINCTRL_APQ8084=y CONFIG_PINCTRL_IPQ8064=y CONFIG_PINCTRL_MSM8960=y CONFIG_PINCTRL_MSM8X74=y +CONFIG_GPIOLIB=y CONFIG_DEBUG_GPIO=y CONFIG_GPIO_SYSFS=y -CONFIG_POWER_SUPPLY=y CONFIG_POWER_RESET=y CONFIG_POWER_RESET_MSM=y CONFIG_THERMAL=y @@ -125,7 +125,7 @@ CONFIG_USB_GADGET=y CONFIG_USB_GADGET_DEBUG_FILES=y CONFIG_USB_GADGET_VBUS_DRAW=500 CONFIG_MMC=y -CONFIG_MMC_BLOCK_MINORS=16 +CONFIG_MMC_BLOCK_MINORS=32 CONFIG_MMC_ARMMMCI=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_PLTFM=y @@ -134,14 +134,15 @@ CONFIG_RTC_CLASS=y CONFIG_DMADEVICES=y CONFIG_QCOM_BAM_DMA=y CONFIG_STAGING=y -CONFIG_QCOM_GSBI=y CONFIG_COMMON_CLK_QCOM=y CONFIG_APQ_MMCC_8084=y -CONFIG_IPQ_GCC_806X=y +CONFIG_IPQ_LCC_806X=y CONFIG_MSM_GCC_8660=y +CONFIG_MSM_LCC_8960=y CONFIG_MSM_MMCC_8960=y CONFIG_MSM_MMCC_8974=y CONFIG_MSM_IOMMU=y +CONFIG_QCOM_GSBI=y CONFIG_PHY_QCOM_APQ8064_SATA=y CONFIG_PHY_QCOM_IPQ806X_SATA=y CONFIG_EXT2_FS=y diff --git a/arch/arm/configs/shmobile_defconfig b/arch/arm/configs/shmobile_defconfig index b17036088726..b58618e2d13c 100644 --- a/arch/arm/configs/shmobile_defconfig +++ b/arch/arm/configs/shmobile_defconfig @@ -12,7 +12,9 @@ CONFIG_SLAB=y CONFIG_ARCH_SHMOBILE_MULTI=y CONFIG_ARCH_EMEV2=y CONFIG_ARCH_R7S72100=y +CONFIG_ARCH_R8A73A4=y CONFIG_ARCH_R8A7740=y +CONFIG_ARCH_R8A7778=y CONFIG_ARCH_R8A7779=y CONFIG_ARCH_R8A7790=y CONFIG_ARCH_R8A7791=y @@ -92,7 +94,6 @@ CONFIG_INPUT_ADXL34X=y # CONFIG_LEGACY_PTYS is not set CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_EM=y CONFIG_SERIAL_SH_SCI=y CONFIG_SERIAL_SH_SCI_NR_UARTS=20 @@ -109,6 +110,9 @@ CONFIG_SPI_SH_HSPI=y CONFIG_GPIO_EM=y CONFIG_GPIO_RCAR=y CONFIG_GPIO_PCF857X=y +CONFIG_POWER_SUPPLY=y +CONFIG_POWER_RESET=y +CONFIG_POWER_RESET_RMOBILE=y # CONFIG_HWMON is not set CONFIG_THERMAL=y CONFIG_CPU_THERMAL=y @@ -121,6 +125,7 @@ CONFIG_REGULATOR=y CONFIG_REGULATOR_AS3711=y CONFIG_REGULATOR_DA9210=y CONFIG_REGULATOR_GPIO=y +CONFIG_REGULATOR_MAX8973=y CONFIG_MEDIA_SUPPORT=y CONFIG_MEDIA_CAMERA_SUPPORT=y CONFIG_MEDIA_CONTROLLER=y @@ -133,6 +138,7 @@ CONFIG_V4L_MEM2MEM_DRIVERS=y CONFIG_VIDEO_RENESAS_VSP1=y # CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set CONFIG_VIDEO_ADV7180=y +CONFIG_VIDEO_ML86V7667=y CONFIG_DRM=y CONFIG_DRM_RCAR_DU=y CONFIG_FB_SH_MOBILE_LCDC=y @@ -167,6 +173,7 @@ CONFIG_LEDS_GPIO=y CONFIG_RTC_CLASS=y CONFIG_RTC_DRV_RS5C372=y CONFIG_RTC_DRV_S35390A=y +CONFIG_RTC_DRV_RX8581=y CONFIG_DMADEVICES=y CONFIG_SH_DMAE=y CONFIG_RCAR_DMAC=y diff --git a/arch/arm/configs/sunxi_defconfig b/arch/arm/configs/sunxi_defconfig index 8f6a5702b696..8ecba00dcd83 100644 --- a/arch/arm/configs/sunxi_defconfig +++ b/arch/arm/configs/sunxi_defconfig @@ -107,6 +107,7 @@ CONFIG_RTC_DRV_SUN6I=y CONFIG_RTC_DRV_SUNXI=y # CONFIG_IOMMU_SUPPORT is not set CONFIG_PHY_SUN4I_USB=y +CONFIG_PHY_SUN9I_USB=y CONFIG_EXT4_FS=y CONFIG_VFAT_FS=y CONFIG_TMPFS=y diff --git a/arch/arm/include/asm/arm-cci.h b/arch/arm/include/asm/arm-cci.h new file mode 100644 index 000000000000..fe77f7ab7e6b --- /dev/null +++ b/arch/arm/include/asm/arm-cci.h @@ -0,0 +1,42 @@ +/* + * arch/arm/include/asm/arm-cci.h + * + * Copyright (C) 2015 ARM Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + */ + +#ifndef __ASM_ARM_CCI_H +#define __ASM_ARM_CCI_H + +#ifdef CONFIG_MCPM +#include + +/* + * We don't have a reliable way of detecting whether, + * if we have access to secure-only registers, unless + * mcpm is registered. + */ +static inline bool platform_has_secure_cci_access(void) +{ + return mcpm_is_available(); +} + +#else +static inline bool platform_has_secure_cci_access(void) +{ + return false; +} +#endif + +#endif diff --git a/arch/arm/include/asm/dma-iommu.h b/arch/arm/include/asm/dma-iommu.h index 8e3fcb924db6..2ef282f96651 100644 --- a/arch/arm/include/asm/dma-iommu.h +++ b/arch/arm/include/asm/dma-iommu.h @@ -25,7 +25,7 @@ struct dma_iommu_mapping { }; struct dma_iommu_mapping * -arm_iommu_create_mapping(struct bus_type *bus, dma_addr_t base, size_t size); +arm_iommu_create_mapping(struct bus_type *bus, dma_addr_t base, u64 size); void arm_iommu_release_mapping(struct dma_iommu_mapping *mapping); diff --git a/arch/arm/include/asm/mcpm.h b/arch/arm/include/asm/mcpm.h index 3446f6a1d9fa..50b378f59e08 100644 --- a/arch/arm/include/asm/mcpm.h +++ b/arch/arm/include/asm/mcpm.h @@ -171,12 +171,73 @@ void mcpm_cpu_suspend(u64 expected_residency); int mcpm_cpu_powered_up(void); /* - * Platform specific methods used in the implementation of the above API. + * Platform specific callbacks used in the implementation of the above API. + * + * cpu_powerup: + * Make given CPU runable. Called with MCPM lock held and IRQs disabled. + * The given cluster is assumed to be set up (cluster_powerup would have + * been called beforehand). Must return 0 for success or negative error code. + * + * cluster_powerup: + * Set up power for given cluster. Called with MCPM lock held and IRQs + * disabled. Called before first cpu_powerup when cluster is down. Must + * return 0 for success or negative error code. + * + * cpu_suspend_prepare: + * Special suspend configuration. Called on target CPU with MCPM lock held + * and IRQs disabled. This callback is optional. If provided, it is called + * before cpu_powerdown_prepare. + * + * cpu_powerdown_prepare: + * Configure given CPU for power down. Called on target CPU with MCPM lock + * held and IRQs disabled. Power down must be effective only at the next WFI instruction. + * + * cluster_powerdown_prepare: + * Configure given cluster for power down. Called on one CPU from target + * cluster with MCPM lock held and IRQs disabled. A cpu_powerdown_prepare + * for each CPU in the cluster has happened when this occurs. + * + * cpu_cache_disable: + * Clean and disable CPU level cache for the calling CPU. Called on with IRQs + * disabled only. The CPU is no longer cache coherent with the rest of the + * system when this returns. + * + * cluster_cache_disable: + * Clean and disable the cluster wide cache as well as the CPU level cache + * for the calling CPU. No call to cpu_cache_disable will happen for this + * CPU. Called with IRQs disabled and only when all the other CPUs are done + * with their own cpu_cache_disable. The cluster is no longer cache coherent + * with the rest of the system when this returns. + * + * cpu_is_up: + * Called on given CPU after it has been powered up or resumed. The MCPM lock + * is held and IRQs disabled. This callback is optional. + * + * cluster_is_up: + * Called by the first CPU to be powered up or resumed in given cluster. + * The MCPM lock is held and IRQs disabled. This callback is optional. If + * provided, it is called before cpu_is_up for that CPU. + * + * wait_for_powerdown: + * Wait until given CPU is powered down. This is called in sleeping context. + * Some reasonable timeout must be considered. Must return 0 for success or + * negative error code. */ struct mcpm_platform_ops { + int (*cpu_powerup)(unsigned int cpu, unsigned int cluster); + int (*cluster_powerup)(unsigned int cluster); + void (*cpu_suspend_prepare)(unsigned int cpu, unsigned int cluster); + void (*cpu_powerdown_prepare)(unsigned int cpu, unsigned int cluster); + void (*cluster_powerdown_prepare)(unsigned int cluster); + void (*cpu_cache_disable)(void); + void (*cluster_cache_disable)(void); + void (*cpu_is_up)(unsigned int cpu, unsigned int cluster); + void (*cluster_is_up)(unsigned int cluster); + int (*wait_for_powerdown)(unsigned int cpu, unsigned int cluster); + + /* deprecated callbacks */ int (*power_up)(unsigned int cpu, unsigned int cluster); void (*power_down)(void); - int (*wait_for_powerdown)(unsigned int cpu, unsigned int cluster); void (*suspend)(u64); void (*powered_up)(void); }; diff --git a/arch/arm/include/asm/xen/page.h b/arch/arm/include/asm/xen/page.h index 2f7e6ff67d51..0b579b2f4e0e 100644 --- a/arch/arm/include/asm/xen/page.h +++ b/arch/arm/include/asm/xen/page.h @@ -110,5 +110,6 @@ static inline bool set_phys_to_machine(unsigned long pfn, unsigned long mfn) bool xen_arch_need_swiotlb(struct device *dev, unsigned long pfn, unsigned long mfn); +unsigned long xen_get_swiotlb_free_pages(unsigned int order); #endif /* _ASM_ARM_XEN_PAGE_H */ diff --git a/arch/arm/include/debug/msm.S b/arch/arm/include/debug/msm.S index e55a9426b496..b03024fa671f 100644 --- a/arch/arm/include/debug/msm.S +++ b/arch/arm/include/debug/msm.S @@ -16,24 +16,17 @@ */ .macro addruart, rp, rv, tmp -#ifdef CONFIG_DEBUG_UART_PHYS ldr \rp, =CONFIG_DEBUG_UART_PHYS ldr \rv, =CONFIG_DEBUG_UART_VIRT -#endif .endm .macro senduart, rd, rx ARM_BE8(rev \rd, \rd ) -#ifdef CONFIG_DEBUG_QCOM_UARTDM @ Write the 1 character to UARTDM_TF str \rd, [\rx, #0x70] -#else - str \rd, [\rx, #0x0C] -#endif .endm .macro waituart, rd, rx -#ifdef CONFIG_DEBUG_QCOM_UARTDM @ check for TX_EMT in UARTDM_SR ldr \rd, [\rx, #0x08] ARM_BE8(rev \rd, \rd ) @@ -55,13 +48,6 @@ ARM_BE8(rev \rd, \rd ) str \rd, [\rx, #0x40] @ UARTDM reg. Read to induce delay ldr \rd, [\rx, #0x08] -#else - @ wait for TX_READY -1001: ldr \rd, [\rx, #0x08] -ARM_BE8(rev \rd, \rd ) - tst \rd, #0x04 - beq 1001b -#endif .endm .macro busyuart, rd, rx diff --git a/arch/arm/include/uapi/asm/kvm.h b/arch/arm/include/uapi/asm/kvm.h index 2499867dd0d8..df3f60cb1168 100644 --- a/arch/arm/include/uapi/asm/kvm.h +++ b/arch/arm/include/uapi/asm/kvm.h @@ -195,8 +195,14 @@ struct kvm_arch_memory_slot { #define KVM_ARM_IRQ_CPU_IRQ 0 #define KVM_ARM_IRQ_CPU_FIQ 1 -/* Highest supported SPI, from VGIC_NR_IRQS */ +/* + * This used to hold the highest supported SPI, but it is now obsolete + * and only here to provide source code level compatibility with older + * userland. The highest SPI number can be set via KVM_DEV_ARM_VGIC_GRP_NR_IRQS. + */ +#ifndef __KERNEL__ #define KVM_ARM_IRQ_GIC_MAX 127 +#endif /* One single KVM irqchip, ie. the VGIC */ #define KVM_NR_IRQCHIPS 1 diff --git a/arch/arm/kernel/head-nommu.S b/arch/arm/kernel/head-nommu.S index cc176b67c134..aebfbf79a1a3 100644 --- a/arch/arm/kernel/head-nommu.S +++ b/arch/arm/kernel/head-nommu.S @@ -80,9 +80,9 @@ ENTRY(stext) ldr r13, =__mmap_switched @ address to jump to after @ initialising sctlr adr lr, BSYM(1f) @ return (PIC) address - ARM( add pc, r10, #PROCINFO_INITFUNC ) - THUMB( add r12, r10, #PROCINFO_INITFUNC ) - THUMB( ret r12 ) + ldr r12, [r10, #PROCINFO_INITFUNC] + add r12, r12, r10 + ret r12 1: b __after_proc_init ENDPROC(stext) @@ -117,9 +117,9 @@ ENTRY(secondary_startup) adr lr, BSYM(__after_proc_init) @ return address mov r13, r12 @ __secondary_switched address - ARM( add pc, r10, #PROCINFO_INITFUNC ) - THUMB( add r12, r10, #PROCINFO_INITFUNC ) - THUMB( ret r12 ) + ldr r12, [r10, #PROCINFO_INITFUNC] + add r12, r12, r10 + ret r12 ENDPROC(secondary_startup) ENTRY(__secondary_switched) diff --git a/arch/arm/kernel/perf_event_cpu.c b/arch/arm/kernel/perf_event_cpu.c index 91c7ba182dcd..213919ba326f 100644 --- a/arch/arm/kernel/perf_event_cpu.c +++ b/arch/arm/kernel/perf_event_cpu.c @@ -303,12 +303,17 @@ static int probe_current_pmu(struct arm_pmu *pmu) static int of_pmu_irq_cfg(struct platform_device *pdev) { - int i; + int i, irq; int *irqs = kcalloc(pdev->num_resources, sizeof(*irqs), GFP_KERNEL); if (!irqs) return -ENOMEM; + /* Don't bother with PPIs; they're already affine */ + irq = platform_get_irq(pdev, 0); + if (irq >= 0 && irq_is_percpu(irq)) + return 0; + for (i = 0; i < pdev->num_resources; ++i) { struct device_node *dn; int cpu; @@ -317,7 +322,7 @@ static int of_pmu_irq_cfg(struct platform_device *pdev) i); if (!dn) { pr_warn("Failed to parse %s/interrupt-affinity[%d]\n", - of_node_full_name(dn), i); + of_node_full_name(pdev->dev.of_node), i); break; } diff --git a/arch/arm/kvm/arm.c b/arch/arm/kvm/arm.c index 6f536451ab78..d9631ecddd56 100644 --- a/arch/arm/kvm/arm.c +++ b/arch/arm/kvm/arm.c @@ -671,8 +671,7 @@ int kvm_vm_ioctl_irq_line(struct kvm *kvm, struct kvm_irq_level *irq_level, if (!irqchip_in_kernel(kvm)) return -ENXIO; - if (irq_num < VGIC_NR_PRIVATE_IRQS || - irq_num > KVM_ARM_IRQ_GIC_MAX) + if (irq_num < VGIC_NR_PRIVATE_IRQS) return -EINVAL; return kvm_vgic_inject_irq(kvm, 0, irq_num, level); diff --git a/arch/arm/mach-alpine/Kconfig b/arch/arm/mach-alpine/Kconfig new file mode 100644 index 000000000000..2c44b930505a --- /dev/null +++ b/arch/arm/mach-alpine/Kconfig @@ -0,0 +1,12 @@ +config ARCH_ALPINE + bool "Annapurna Labs Alpine platform" if ARCH_MULTI_V7 + select ARM_AMBA + select ARM_GIC + select GENERIC_IRQ_CHIP + select HAVE_ARM_ARCH_TIMER + select HAVE_SMP + select MFD_SYSCON + select PCI + select PCI_HOST_GENERIC + help + This enables support for the Annapurna Labs Alpine V1 boards. diff --git a/arch/arm/mach-alpine/Makefile b/arch/arm/mach-alpine/Makefile new file mode 100644 index 000000000000..b6674890be71 --- /dev/null +++ b/arch/arm/mach-alpine/Makefile @@ -0,0 +1,2 @@ +obj-y += alpine_machine.o +obj-$(CONFIG_SMP) += platsmp.o alpine_cpu_pm.o diff --git a/arch/arm/mach-alpine/alpine_cpu_pm.c b/arch/arm/mach-alpine/alpine_cpu_pm.c new file mode 100644 index 000000000000..121c77c4b53c --- /dev/null +++ b/arch/arm/mach-alpine/alpine_cpu_pm.c @@ -0,0 +1,70 @@ +/* + * Low-level power-management support for Alpine platform. + * + * Copyright (C) 2015 Annapurna Labs Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include + +#include "alpine_cpu_pm.h" +#include "alpine_cpu_resume.h" + +/* NB registers */ +#define AL_SYSFAB_POWER_CONTROL(cpu) (0x2000 + (cpu)*0x100 + 0x20) + +static struct regmap *al_sysfabric; +static struct al_cpu_resume_regs __iomem *al_cpu_resume_regs; +static int wakeup_supported; + +int alpine_cpu_wakeup(unsigned int phys_cpu, uint32_t phys_resume_addr) +{ + if (!wakeup_supported) + return -ENOSYS; + + /* + * Set CPU resume address - + * secure firmware running on boot will jump to this address + * after setting proper CPU mode, and initialiing e.g. secure + * regs (the same mode all CPUs are booted to - usually HYP) + */ + writel(phys_resume_addr, + &al_cpu_resume_regs->per_cpu[phys_cpu].resume_addr); + + /* Power-up the CPU */ + regmap_write(al_sysfabric, AL_SYSFAB_POWER_CONTROL(phys_cpu), 0); + + return 0; +} + +void __init alpine_cpu_pm_init(void) +{ + struct device_node *np; + uint32_t watermark; + + al_sysfabric = syscon_regmap_lookup_by_compatible("al,alpine-sysfabric-service"); + + np = of_find_compatible_node(NULL, NULL, "al,alpine-cpu-resume"); + al_cpu_resume_regs = of_iomap(np, 0); + + wakeup_supported = !IS_ERR(al_sysfabric) && al_cpu_resume_regs; + + if (wakeup_supported) { + watermark = readl(&al_cpu_resume_regs->watermark); + wakeup_supported = (watermark & AL_CPU_RESUME_MAGIC_NUM_MASK) + == AL_CPU_RESUME_MAGIC_NUM; + } +} diff --git a/arch/arm/mach-at91/include/mach/io.h b/arch/arm/mach-alpine/alpine_cpu_pm.h similarity index 55% rename from arch/arm/mach-at91/include/mach/io.h rename to arch/arm/mach-alpine/alpine_cpu_pm.h index 2d9ca0455745..5179e697c492 100644 --- a/arch/arm/mach-at91/include/mach/io.h +++ b/arch/arm/mach-alpine/alpine_cpu_pm.h @@ -1,7 +1,7 @@ /* - * arch/arm/mach-at91/include/mach/io.h + * Low-level power-management support for Alpine platform. * - * Copyright (C) 2003 SAN People + * Copyright (C) 2015 Annapurna Labs Ltd. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -12,16 +12,15 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -#ifndef __ASM_ARCH_IO_H -#define __ASM_ARCH_IO_H +#ifndef __ALPINE_CPU_PM_H__ +#define __ALPINE_CPU_PM_H__ -#define IO_SPACE_LIMIT 0xFFFFFFFF -#define __io(a) __typesafe_io(a) +/* Alpine CPU Power Management Services Initialization */ +void alpine_cpu_pm_init(void); -#endif +/* Wake-up a CPU */ +int alpine_cpu_wakeup(unsigned int phys_cpu, uint32_t phys_resume_addr); + +#endif /* __ALPINE_CPU_PM_H__ */ diff --git a/arch/arm/mach-alpine/alpine_cpu_resume.h b/arch/arm/mach-alpine/alpine_cpu_resume.h new file mode 100644 index 000000000000..c80150c0d2d8 --- /dev/null +++ b/arch/arm/mach-alpine/alpine_cpu_resume.h @@ -0,0 +1,38 @@ +/* + * Annapurna labs cpu-resume register structure. + * + * Copyright (C) 2015 Annapurna Labs Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef ALPINE_CPU_RESUME_H_ +#define ALPINE_CPU_RESUME_H_ + +/* Per-cpu regs */ +struct al_cpu_resume_regs_per_cpu { + uint32_t flags; + uint32_t resume_addr; +}; + +/* general regs */ +struct al_cpu_resume_regs { + /* Watermark for validating the CPU resume struct */ + uint32_t watermark; + uint32_t flags; + struct al_cpu_resume_regs_per_cpu per_cpu[]; +}; + +/* The expected magic number for validating the resume addresses */ +#define AL_CPU_RESUME_MAGIC_NUM 0xf0e1d200 +#define AL_CPU_RESUME_MAGIC_NUM_MASK 0xffffff00 + +#endif /* ALPINE_CPU_RESUME_H_ */ diff --git a/arch/arm/mach-alpine/alpine_machine.c b/arch/arm/mach-alpine/alpine_machine.c new file mode 100644 index 000000000000..b8e2145e962b --- /dev/null +++ b/arch/arm/mach-alpine/alpine_machine.c @@ -0,0 +1,28 @@ +/* + * Machine declaration for Alpine platforms. + * + * Copyright (C) 2015 Annapurna Labs Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include + +#include + +static const char * const al_match[] __initconst = { + "al,alpine", + NULL, +}; + +DT_MACHINE_START(AL_DT, "Annapurna Labs Alpine") + .dt_compat = al_match, +MACHINE_END diff --git a/arch/arm/mach-alpine/platsmp.c b/arch/arm/mach-alpine/platsmp.c new file mode 100644 index 000000000000..f78429f48bd6 --- /dev/null +++ b/arch/arm/mach-alpine/platsmp.c @@ -0,0 +1,49 @@ +/* + * SMP operations for Alpine platform. + * + * Copyright (C) 2015 Annapurna Labs Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include + +#include + +#include "alpine_cpu_pm.h" + +static int alpine_boot_secondary(unsigned int cpu, struct task_struct *idle) +{ + phys_addr_t addr; + + addr = virt_to_phys(secondary_startup); + + if (addr > (phys_addr_t)(uint32_t)(-1)) { + pr_err("FAIL: resume address over 32bit (%pa)", &addr); + return -EINVAL; + } + + return alpine_cpu_wakeup(cpu_logical_map(cpu), (uint32_t)addr); +} + +static void __init alpine_smp_prepare_cpus(unsigned int max_cpus) +{ + alpine_cpu_pm_init(); +} + +static struct smp_operations alpine_smp_ops __initdata = { + .smp_prepare_cpus = alpine_smp_prepare_cpus, + .smp_boot_secondary = alpine_boot_secondary, +}; +CPU_METHOD_OF_DECLARE(alpine_smp, "al,alpine-smp", &alpine_smp_ops); diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index c74a44324e5b..fd95f34945f4 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -1,55 +1,15 @@ -if ARCH_AT91 - -config HAVE_AT91_UTMI - bool - -config HAVE_AT91_USB_CLK - bool - -config COMMON_CLK_AT91 - bool - select COMMON_CLK - -config HAVE_AT91_SMD - bool - -config HAVE_AT91_H32MX - bool - -config SOC_SAMA5 - bool - select ATMEL_AIC5_IRQ +menuconfig ARCH_AT91 + bool "Atmel SoCs" + depends on ARCH_MULTI_V4T || ARCH_MULTI_V5 || ARCH_MULTI_V7 + select ARCH_REQUIRE_GPIOLIB select COMMON_CLK_AT91 - select CPU_V7 - select GENERIC_CLOCKEVENTS - select MEMORY - select ATMEL_SDRAMC - select PHYLIB if NETDEVICES + select PINCTRL + select PINCTRL_AT91 + select SOC_BUS -menu "Atmel AT91 System-on-Chip" - -choice - - prompt "Core type" - -config SOC_SAM_V4_V5 - bool "ARM9 AT91SAM9/AT91RM9200" - help - Select this if you are using one of Atmel's AT91SAM9 or - AT91RM9200 SoC. - -config SOC_SAM_V7 - bool "Cortex A5" - help - Select this if you are using one of Atmel's SAMA5D3 SoC. - -endchoice - -comment "Atmel AT91 Processor" - -if SOC_SAM_V7 +if ARCH_AT91 config SOC_SAMA5D3 - bool "SAMA5D3 family" + bool "SAMA5D3 family" if ARCH_MULTI_V7 select SOC_SAMA5 select HAVE_FB_ATMEL select HAVE_AT91_UTMI @@ -60,9 +20,8 @@ config SOC_SAMA5D3 This support covers SAMA5D31, SAMA5D33, SAMA5D34, SAMA5D35, SAMA5D36. config SOC_SAMA5D4 - bool "SAMA5D4 family" + bool "SAMA5D4 family" if ARCH_MULTI_V7 select SOC_SAMA5 - select CLKSRC_MMIO select CACHE_L2X0 select HAVE_FB_ATMEL select HAVE_AT91_UTMI @@ -71,29 +30,31 @@ config SOC_SAMA5D4 select HAVE_AT91_H32MX help Select this if you are using one of Atmel's SAMA5D4 family SoC. -endif -if SOC_SAM_V4_V5 config SOC_AT91RM9200 - bool "AT91RM9200" + bool "AT91RM9200" if ARCH_MULTI_V4T select ATMEL_AIC_IRQ - select COMMON_CLK_AT91 + select ATMEL_ST select CPU_ARM920T - select GENERIC_CLOCKEVENTS select HAVE_AT91_USB_CLK + select MIGHT_HAVE_PCI + select SOC_SAM_V4_V5 + select SRAM if PM + help + Select this if you are using Atmel's AT91RM9200 SoC. config SOC_AT91SAM9 - bool "AT91SAM9" + bool "AT91SAM9" if ARCH_MULTI_V5 select ATMEL_AIC_IRQ select ATMEL_SDRAMC - select COMMON_CLK_AT91 select CPU_ARM926T - select GENERIC_CLOCKEVENTS select HAVE_AT91_SMD select HAVE_AT91_USB_CLK select HAVE_AT91_UTMI select HAVE_FB_ATMEL select MEMORY + select SOC_SAM_V4_V5 + select SRAM if PM help Select this if you are using one of those Atmel SoC: AT91SAM9260 @@ -112,40 +73,35 @@ config SOC_AT91SAM9 AT91SAM9X25 AT91SAM9X35 AT91SAM9XE -endif # SOC_SAM_V4_V5 -comment "AT91 Feature Selections" +config HAVE_AT91_UTMI + bool -config AT91_SLOW_CLOCK - bool "Suspend-to-RAM disables main oscillator" - select SRAM - depends on SUSPEND - help - Select this if you want Suspend-to-RAM to save the most power - possible (without powering off the CPU) by disabling the PLLs - and main oscillator so that only the 32 KiHz clock is available. +config HAVE_AT91_USB_CLK + bool - When only that slow-clock is available, some peripherals lose - functionality. Many can't issue wakeup events unless faster - clocks are available. Some lose their operating state and - need to be completely re-initialized. +config COMMON_CLK_AT91 + bool + select COMMON_CLK -config AT91_TIMER_HZ - int "Kernel HZ (jiffies per second)" - range 32 1024 - depends on ARCH_AT91 - default "128" if SOC_AT91RM9200 - default "100" - help - On AT91rm9200 chips where you're using a system clock derived - from the 32768 Hz hardware clock, this tick rate should divide - it exactly: use a power-of-two value, such as 128 or 256, to - reduce timing errors caused by rounding. +config HAVE_AT91_SMD + bool - On AT91sam926x chips, or otherwise when using a higher precision - system clock (of at least several MHz), rounding is less of a - problem so it can be safer to use a decimal values like 100. +config HAVE_AT91_H32MX + bool -endmenu +config SOC_SAM_V4_V5 + bool + +config SOC_SAM_V7 + bool + +config SOC_SAMA5 + bool + select ATMEL_AIC5_IRQ + select ATMEL_SDRAMC + select MEMORY + select SOC_SAM_V7 + select SRAM if PM endif diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 827fdbcce1c7..4fa8b4541e64 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -1,20 +1,25 @@ # # Makefile for the linux kernel. # +ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include +asflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include -obj-y := setup.o +obj-y := soc.o obj-$(CONFIG_SOC_AT91SAM9) += sam9_smc.o # CPU-specific support -obj-$(CONFIG_SOC_AT91RM9200) += at91rm9200.o at91rm9200_time.o +obj-$(CONFIG_SOC_AT91RM9200) += at91rm9200.o obj-$(CONFIG_SOC_AT91SAM9) += at91sam9.o obj-$(CONFIG_SOC_SAMA5) += sama5.o # Power Management obj-$(CONFIG_PM) += pm.o -obj-$(CONFIG_AT91_SLOW_CLOCK) += pm_slowclock.o +obj-$(CONFIG_PM) += pm_suspend.o +ifeq ($(CONFIG_CPU_V7),y) +AFLAGS_pm_suspend.o := -march=armv7-a +endif ifeq ($(CONFIG_PM_DEBUG),y) CFLAGS_pm.o += -DDEBUG endif diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c index 8fcfb70f7124..eaf58f88ef5d 100644 --- a/arch/arm/mach-at91/at91rm9200.c +++ b/arch/arm/mach-at91/at91rm9200.c @@ -8,60 +8,42 @@ * Licensed under GPLv2 or later. */ -#include -#include -#include -#include -#include -#include -#include #include +#include +#include -#include -#include #include -#include -#include #include -#include - #include "generic.h" +#include "soc.h" -static void at91rm9200_restart(enum reboot_mode reboot_mode, const char *cmd) -{ - /* - * Perform a hardware reset with the use of the Watchdog timer. - */ - at91_st_write(AT91_ST_WDMR, AT91_ST_RSTEN | AT91_ST_EXTEN | 1); - at91_st_write(AT91_ST_CR, AT91_ST_WDRST); -} - -static void __init at91rm9200_dt_timer_init(void) -{ - of_clk_init(NULL); - at91rm9200_timer_init(); -} +static const struct at91_soc rm9200_socs[] = { + AT91_SOC(AT91RM9200_CIDR_MATCH, 0, "at91rm9200 BGA", "at91rm9200"), + { /* sentinel */ }, +}; static void __init at91rm9200_dt_device_init(void) { - of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); + struct soc_device *soc; + struct device *soc_dev = NULL; + + soc = at91_soc_init(rm9200_socs); + if (soc != NULL) + soc_dev = soc_device_to_device(soc); + + of_platform_populate(NULL, of_default_bus_match_table, NULL, soc_dev); arm_pm_idle = at91rm9200_idle; - arm_pm_restart = at91rm9200_restart; at91rm9200_pm_init(); } - - static const char *at91rm9200_dt_board_compat[] __initconst = { "atmel,at91rm9200", NULL }; DT_MACHINE_START(at91rm9200_dt, "Atmel AT91RM9200") - .init_time = at91rm9200_dt_timer_init, - .map_io = at91_map_io, .init_machine = at91rm9200_dt_device_init, .dt_compat = at91rm9200_dt_board_compat, MACHINE_END diff --git a/arch/arm/mach-at91/at91sam9.c b/arch/arm/mach-at91/at91sam9.c index 56e3ba73ec40..e47a2093a0e7 100644 --- a/arch/arm/mach-at91/at91sam9.c +++ b/arch/arm/mach-at91/at91sam9.c @@ -7,29 +7,68 @@ * Licensed under GPLv2 or later. */ -#include -#include -#include -#include #include -#include #include -#include -#include -#include -#include #include -#include -#include +#include #include "generic.h" +#include "soc.h" + +static const struct at91_soc at91sam9_socs[] = { + AT91_SOC(AT91SAM9260_CIDR_MATCH, 0, "at91sam9260", NULL), + AT91_SOC(AT91SAM9261_CIDR_MATCH, 0, "at91sam9261", NULL), + AT91_SOC(AT91SAM9263_CIDR_MATCH, 0, "at91sam9263", NULL), + AT91_SOC(AT91SAM9G20_CIDR_MATCH, 0, "at91sam9g20", NULL), + AT91_SOC(AT91SAM9RL64_CIDR_MATCH, 0, "at91sam9rl64", NULL), + AT91_SOC(AT91SAM9G45_CIDR_MATCH, AT91SAM9M11_EXID_MATCH, + "at91sam9m11", "at91sam9g45"), + AT91_SOC(AT91SAM9G45_CIDR_MATCH, AT91SAM9M10_EXID_MATCH, + "at91sam9m10", "at91sam9g45"), + AT91_SOC(AT91SAM9G45_CIDR_MATCH, AT91SAM9G46_EXID_MATCH, + "at91sam9g46", "at91sam9g45"), + AT91_SOC(AT91SAM9G45_CIDR_MATCH, AT91SAM9G45_EXID_MATCH, + "at91sam9g45", "at91sam9g45"), + AT91_SOC(AT91SAM9X5_CIDR_MATCH, AT91SAM9G15_EXID_MATCH, + "at91sam9g15", "at91sam9x5"), + AT91_SOC(AT91SAM9X5_CIDR_MATCH, AT91SAM9G35_EXID_MATCH, + "at91sam9g35", "at91sam9x5"), + AT91_SOC(AT91SAM9X5_CIDR_MATCH, AT91SAM9X35_EXID_MATCH, + "at91sam9x35", "at91sam9x5"), + AT91_SOC(AT91SAM9X5_CIDR_MATCH, AT91SAM9G25_EXID_MATCH, + "at91sam9g25", "at91sam9x5"), + AT91_SOC(AT91SAM9X5_CIDR_MATCH, AT91SAM9X25_EXID_MATCH, + "at91sam9x25", "at91sam9x5"), + AT91_SOC(AT91SAM9N12_CIDR_MATCH, AT91SAM9CN12_EXID_MATCH, + "at91sam9cn12", "at91sam9n12"), + AT91_SOC(AT91SAM9N12_CIDR_MATCH, AT91SAM9N12_EXID_MATCH, + "at91sam9n12", "at91sam9n12"), + AT91_SOC(AT91SAM9N12_CIDR_MATCH, AT91SAM9CN11_EXID_MATCH, + "at91sam9cn11", "at91sam9n12"), + AT91_SOC(AT91SAM9XE128_CIDR_MATCH, 0, "at91sam9xe128", "at91sam9xe128"), + AT91_SOC(AT91SAM9XE256_CIDR_MATCH, 0, "at91sam9xe256", "at91sam9xe256"), + AT91_SOC(AT91SAM9XE512_CIDR_MATCH, 0, "at91sam9xe512", "at91sam9xe512"), + { /* sentinel */ }, +}; + +static void __init at91sam9_common_init(void) +{ + struct soc_device *soc; + struct device *soc_dev = NULL; + + soc = at91_soc_init(at91sam9_socs); + if (soc != NULL) + soc_dev = soc_device_to_device(soc); + + of_platform_populate(NULL, of_default_bus_match_table, NULL, soc_dev); + + arm_pm_idle = at91sam9_idle; +} static void __init at91sam9_dt_device_init(void) { - of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); - - arm_pm_idle = at91sam9_idle; + at91sam9_common_init(); at91sam9260_pm_init(); } @@ -40,16 +79,13 @@ static const char *at91_dt_board_compat[] __initconst = { DT_MACHINE_START(at91sam_dt, "Atmel AT91SAM9") /* Maintainer: Atmel */ - .map_io = at91_map_io, .init_machine = at91sam9_dt_device_init, .dt_compat = at91_dt_board_compat, MACHINE_END static void __init at91sam9g45_dt_device_init(void) { - of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); - - arm_pm_idle = at91sam9_idle; + at91sam9_common_init(); at91sam9g45_pm_init(); } @@ -60,16 +96,13 @@ static const char *at91sam9g45_board_compat[] __initconst = { DT_MACHINE_START(at91sam9g45_dt, "Atmel AT91SAM9G45") /* Maintainer: Atmel */ - .map_io = at91_map_io, .init_machine = at91sam9g45_dt_device_init, .dt_compat = at91sam9g45_board_compat, MACHINE_END static void __init at91sam9x5_dt_device_init(void) { - of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); - - arm_pm_idle = at91sam9_idle; + at91sam9_common_init(); at91sam9x5_pm_init(); } @@ -81,7 +114,6 @@ static const char *at91sam9x5_board_compat[] __initconst = { DT_MACHINE_START(at91sam9x5_dt, "Atmel AT91SAM9") /* Maintainer: Atmel */ - .map_io = at91_map_io, .init_machine = at91sam9x5_dt_device_init, .dt_compat = at91sam9x5_board_compat, MACHINE_END diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h index 583369ffc284..b0fa7dc7286d 100644 --- a/arch/arm/mach-at91/generic.h +++ b/arch/arm/mach-at91/generic.h @@ -18,17 +18,10 @@ extern void __init at91_map_io(void); extern void __init at91_alt_map_io(void); - /* Timer */ -extern void at91rm9200_timer_init(void); - /* idle */ extern void at91rm9200_idle(void); extern void at91sam9_idle(void); -/* Matrix */ -extern void at91_ioremap_matrix(u32 base_addr); - - #ifdef CONFIG_PM extern void __init at91rm9200_pm_init(void); extern void __init at91sam9260_pm_init(void); diff --git a/arch/arm/mach-at91/include/mach/at91_dbgu.h b/arch/arm/mach-at91/include/mach/at91_dbgu.h deleted file mode 100644 index 42925e8f78e4..000000000000 --- a/arch/arm/mach-at91/include/mach/at91_dbgu.h +++ /dev/null @@ -1,63 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/at91_dbgu.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * Debug Unit (DBGU) - System peripherals registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_DBGU_H -#define AT91_DBGU_H - -#define AT91_DBGU_CR (0x00) /* Control Register */ -#define AT91_DBGU_MR (0x04) /* Mode Register */ -#define AT91_DBGU_IER (0x08) /* Interrupt Enable Register */ -#define AT91_DBGU_TXRDY (1 << 1) /* Transmitter Ready */ -#define AT91_DBGU_TXEMPTY (1 << 9) /* Transmitter Empty */ -#define AT91_DBGU_IDR (0x0c) /* Interrupt Disable Register */ -#define AT91_DBGU_IMR (0x10) /* Interrupt Mask Register */ -#define AT91_DBGU_SR (0x14) /* Status Register */ -#define AT91_DBGU_RHR (0x18) /* Receiver Holding Register */ -#define AT91_DBGU_THR (0x1c) /* Transmitter Holding Register */ -#define AT91_DBGU_BRGR (0x20) /* Baud Rate Generator Register */ - -#define AT91_DBGU_CIDR (0x40) /* Chip ID Register */ -#define AT91_DBGU_EXID (0x44) /* Chip ID Extension Register */ -#define AT91_DBGU_FNR (0x48) /* Force NTRST Register [SAM9 only] */ -#define AT91_DBGU_FNTRST (1 << 0) /* Force NTRST */ - -/* - * Some AT91 parts that don't have full DEBUG units still support the ID - * and extensions register. - */ -#define AT91_CIDR_VERSION (0x1f << 0) /* Version of the Device */ -#define AT91_CIDR_EPROC (7 << 5) /* Embedded Processor */ -#define AT91_CIDR_NVPSIZ (0xf << 8) /* Nonvolatile Program Memory Size */ -#define AT91_CIDR_NVPSIZ2 (0xf << 12) /* Second Nonvolatile Program Memory Size */ -#define AT91_CIDR_SRAMSIZ (0xf << 16) /* Internal SRAM Size */ -#define AT91_CIDR_SRAMSIZ_1K (1 << 16) -#define AT91_CIDR_SRAMSIZ_2K (2 << 16) -#define AT91_CIDR_SRAMSIZ_112K (4 << 16) -#define AT91_CIDR_SRAMSIZ_4K (5 << 16) -#define AT91_CIDR_SRAMSIZ_80K (6 << 16) -#define AT91_CIDR_SRAMSIZ_160K (7 << 16) -#define AT91_CIDR_SRAMSIZ_8K (8 << 16) -#define AT91_CIDR_SRAMSIZ_16K (9 << 16) -#define AT91_CIDR_SRAMSIZ_32K (10 << 16) -#define AT91_CIDR_SRAMSIZ_64K (11 << 16) -#define AT91_CIDR_SRAMSIZ_128K (12 << 16) -#define AT91_CIDR_SRAMSIZ_256K (13 << 16) -#define AT91_CIDR_SRAMSIZ_96K (14 << 16) -#define AT91_CIDR_SRAMSIZ_512K (15 << 16) -#define AT91_CIDR_ARCH (0xff << 20) /* Architecture Identifier */ -#define AT91_CIDR_NVPTYP (7 << 28) /* Nonvolatile Program Memory Type */ -#define AT91_CIDR_EXT (1 << 31) /* Extension Flag */ - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91_matrix.h b/arch/arm/mach-at91/include/mach/at91_matrix.h deleted file mode 100644 index f8996c954131..000000000000 --- a/arch/arm/mach-at91/include/mach/at91_matrix.h +++ /dev/null @@ -1,23 +0,0 @@ -/* - * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD - * - * Under GPLv2 - */ - -#ifndef __MACH_AT91_MATRIX_H__ -#define __MACH_AT91_MATRIX_H__ - -#ifndef __ASSEMBLY__ -extern void __iomem *at91_matrix_base; - -#define at91_matrix_read(field) \ - __raw_readl(at91_matrix_base + field) - -#define at91_matrix_write(field, value) \ - __raw_writel(value, at91_matrix_base + field) - -#else -.extern at91_matrix_base -#endif - -#endif /* __MACH_AT91_MATRIX_H__ */ diff --git a/arch/arm/mach-at91/include/mach/at91_ramc.h b/arch/arm/mach-at91/include/mach/at91_ramc.h index e4492b151fee..493bc486e858 100644 --- a/arch/arm/mach-at91/include/mach/at91_ramc.h +++ b/arch/arm/mach-at91/include/mach/at91_ramc.h @@ -21,10 +21,6 @@ extern void __iomem *at91_ramc_base[]; .extern at91_ramc_base #endif -#define AT91_MEMCTRL_MC 0 -#define AT91_MEMCTRL_SDRAMC 1 -#define AT91_MEMCTRL_DDRSDR 2 - #include #include #include diff --git a/arch/arm/mach-at91/include/mach/at91_st.h b/arch/arm/mach-at91/include/mach/at91_st.h deleted file mode 100644 index 67fdbd13c3ed..000000000000 --- a/arch/arm/mach-at91/include/mach/at91_st.h +++ /dev/null @@ -1,61 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/at91_st.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * System Timer (ST) - System peripherals registers. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_ST_H -#define AT91_ST_H - -#ifndef __ASSEMBLY__ -extern void __iomem *at91_st_base; - -#define at91_st_read(field) \ - __raw_readl(at91_st_base + field) - -#define at91_st_write(field, value) \ - __raw_writel(value, at91_st_base + field) -#else -.extern at91_st_base -#endif - -#define AT91_ST_CR 0x00 /* Control Register */ -#define AT91_ST_WDRST (1 << 0) /* Watchdog Timer Restart */ - -#define AT91_ST_PIMR 0x04 /* Period Interval Mode Register */ -#define AT91_ST_PIV (0xffff << 0) /* Period Interval Value */ - -#define AT91_ST_WDMR 0x08 /* Watchdog Mode Register */ -#define AT91_ST_WDV (0xffff << 0) /* Watchdog Counter Value */ -#define AT91_ST_RSTEN (1 << 16) /* Reset Enable */ -#define AT91_ST_EXTEN (1 << 17) /* External Signal Assertion Enable */ - -#define AT91_ST_RTMR 0x0c /* Real-time Mode Register */ -#define AT91_ST_RTPRES (0xffff << 0) /* Real-time Prescalar Value */ - -#define AT91_ST_SR 0x10 /* Status Register */ -#define AT91_ST_PITS (1 << 0) /* Period Interval Timer Status */ -#define AT91_ST_WDOVF (1 << 1) /* Watchdog Overflow */ -#define AT91_ST_RTTINC (1 << 2) /* Real-time Timer Increment */ -#define AT91_ST_ALMS (1 << 3) /* Alarm Status */ - -#define AT91_ST_IER 0x14 /* Interrupt Enable Register */ -#define AT91_ST_IDR 0x18 /* Interrupt Disable Register */ -#define AT91_ST_IMR 0x1c /* Interrupt Mask Register */ - -#define AT91_ST_RTAR 0x20 /* Real-time Alarm Register */ -#define AT91_ST_ALMV (0xfffff << 0) /* Alarm Value */ - -#define AT91_ST_CRTR 0x24 /* Current Real-time Register */ -#define AT91_ST_CRTV (0xfffff << 0) /* Current Real-Time Value */ - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91rm9200.h b/arch/arm/mach-at91/include/mach/at91rm9200.h deleted file mode 100644 index e67317c67761..000000000000 --- a/arch/arm/mach-at91/include/mach/at91rm9200.h +++ /dev/null @@ -1,103 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/at91rm9200.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * Common definitions. - * Based on AT91RM9200 datasheet revision E. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91RM9200_H -#define AT91RM9200_H - -/* - * Peripheral identifiers/interrupts. - */ -#define AT91RM9200_ID_PIOA 2 /* Parallel IO Controller A */ -#define AT91RM9200_ID_PIOB 3 /* Parallel IO Controller B */ -#define AT91RM9200_ID_PIOC 4 /* Parallel IO Controller C */ -#define AT91RM9200_ID_PIOD 5 /* Parallel IO Controller D */ -#define AT91RM9200_ID_US0 6 /* USART 0 */ -#define AT91RM9200_ID_US1 7 /* USART 1 */ -#define AT91RM9200_ID_US2 8 /* USART 2 */ -#define AT91RM9200_ID_US3 9 /* USART 3 */ -#define AT91RM9200_ID_MCI 10 /* Multimedia Card Interface */ -#define AT91RM9200_ID_UDP 11 /* USB Device Port */ -#define AT91RM9200_ID_TWI 12 /* Two-Wire Interface */ -#define AT91RM9200_ID_SPI 13 /* Serial Peripheral Interface */ -#define AT91RM9200_ID_SSC0 14 /* Serial Synchronous Controller 0 */ -#define AT91RM9200_ID_SSC1 15 /* Serial Synchronous Controller 1 */ -#define AT91RM9200_ID_SSC2 16 /* Serial Synchronous Controller 2 */ -#define AT91RM9200_ID_TC0 17 /* Timer Counter 0 */ -#define AT91RM9200_ID_TC1 18 /* Timer Counter 1 */ -#define AT91RM9200_ID_TC2 19 /* Timer Counter 2 */ -#define AT91RM9200_ID_TC3 20 /* Timer Counter 3 */ -#define AT91RM9200_ID_TC4 21 /* Timer Counter 4 */ -#define AT91RM9200_ID_TC5 22 /* Timer Counter 5 */ -#define AT91RM9200_ID_UHP 23 /* USB Host port */ -#define AT91RM9200_ID_EMAC 24 /* Ethernet MAC */ -#define AT91RM9200_ID_IRQ0 25 /* Advanced Interrupt Controller (IRQ0) */ -#define AT91RM9200_ID_IRQ1 26 /* Advanced Interrupt Controller (IRQ1) */ -#define AT91RM9200_ID_IRQ2 27 /* Advanced Interrupt Controller (IRQ2) */ -#define AT91RM9200_ID_IRQ3 28 /* Advanced Interrupt Controller (IRQ3) */ -#define AT91RM9200_ID_IRQ4 29 /* Advanced Interrupt Controller (IRQ4) */ -#define AT91RM9200_ID_IRQ5 30 /* Advanced Interrupt Controller (IRQ5) */ -#define AT91RM9200_ID_IRQ6 31 /* Advanced Interrupt Controller (IRQ6) */ - - -/* - * Peripheral physical base addresses. - */ -#define AT91RM9200_BASE_TCB0 0xfffa0000 -#define AT91RM9200_BASE_TC0 0xfffa0000 -#define AT91RM9200_BASE_TC1 0xfffa0040 -#define AT91RM9200_BASE_TC2 0xfffa0080 -#define AT91RM9200_BASE_TCB1 0xfffa4000 -#define AT91RM9200_BASE_TC3 0xfffa4000 -#define AT91RM9200_BASE_TC4 0xfffa4040 -#define AT91RM9200_BASE_TC5 0xfffa4080 -#define AT91RM9200_BASE_UDP 0xfffb0000 -#define AT91RM9200_BASE_MCI 0xfffb4000 -#define AT91RM9200_BASE_TWI 0xfffb8000 -#define AT91RM9200_BASE_EMAC 0xfffbc000 -#define AT91RM9200_BASE_US0 0xfffc0000 -#define AT91RM9200_BASE_US1 0xfffc4000 -#define AT91RM9200_BASE_US2 0xfffc8000 -#define AT91RM9200_BASE_US3 0xfffcc000 -#define AT91RM9200_BASE_SSC0 0xfffd0000 -#define AT91RM9200_BASE_SSC1 0xfffd4000 -#define AT91RM9200_BASE_SSC2 0xfffd8000 -#define AT91RM9200_BASE_SPI 0xfffe0000 - - -/* - * System Peripherals - */ -#define AT91RM9200_BASE_DBGU AT91_BASE_DBGU0 /* Debug Unit */ -#define AT91RM9200_BASE_PIOA 0xfffff400 /* PIO Controller A */ -#define AT91RM9200_BASE_PIOB 0xfffff600 /* PIO Controller B */ -#define AT91RM9200_BASE_PIOC 0xfffff800 /* PIO Controller C */ -#define AT91RM9200_BASE_PIOD 0xfffffa00 /* PIO Controller D */ -#define AT91RM9200_BASE_ST 0xfffffd00 /* System Timer */ -#define AT91RM9200_BASE_RTC 0xfffffe00 /* Real-Time Clock */ -#define AT91RM9200_BASE_MC 0xffffff00 /* Memory Controllers */ - -/* - * Internal Memory. - */ -#define AT91RM9200_ROM_BASE 0x00100000 /* Internal ROM base address */ -#define AT91RM9200_ROM_SIZE SZ_128K /* Internal ROM size (128Kb) */ - -#define AT91RM9200_SRAM_BASE 0x00200000 /* Internal SRAM base address */ -#define AT91RM9200_SRAM_SIZE SZ_16K /* Internal SRAM size (16Kb) */ - -#define AT91RM9200_UHP_BASE 0x00300000 /* USB Host controller */ - - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9260.h b/arch/arm/mach-at91/include/mach/at91sam9260.h deleted file mode 100644 index 416c7b6c56d3..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9260.h +++ /dev/null @@ -1,129 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/at91sam9260.h - * - * (C) 2006 Andrew Victor - * - * Common definitions. - * Based on AT91SAM9260 datasheet revision A (Preliminary). - * - * Includes also definitions for AT91SAM9XE and AT91SAM9G families - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91SAM9260_H -#define AT91SAM9260_H - -/* - * Peripheral identifiers/interrupts. - */ -#define AT91SAM9260_ID_PIOA 2 /* Parallel IO Controller A */ -#define AT91SAM9260_ID_PIOB 3 /* Parallel IO Controller B */ -#define AT91SAM9260_ID_PIOC 4 /* Parallel IO Controller C */ -#define AT91SAM9260_ID_ADC 5 /* Analog-to-Digital Converter */ -#define AT91SAM9260_ID_US0 6 /* USART 0 */ -#define AT91SAM9260_ID_US1 7 /* USART 1 */ -#define AT91SAM9260_ID_US2 8 /* USART 2 */ -#define AT91SAM9260_ID_MCI 9 /* Multimedia Card Interface */ -#define AT91SAM9260_ID_UDP 10 /* USB Device Port */ -#define AT91SAM9260_ID_TWI 11 /* Two-Wire Interface */ -#define AT91SAM9260_ID_SPI0 12 /* Serial Peripheral Interface 0 */ -#define AT91SAM9260_ID_SPI1 13 /* Serial Peripheral Interface 1 */ -#define AT91SAM9260_ID_SSC 14 /* Serial Synchronous Controller */ -#define AT91SAM9260_ID_TC0 17 /* Timer Counter 0 */ -#define AT91SAM9260_ID_TC1 18 /* Timer Counter 1 */ -#define AT91SAM9260_ID_TC2 19 /* Timer Counter 2 */ -#define AT91SAM9260_ID_UHP 20 /* USB Host port */ -#define AT91SAM9260_ID_EMAC 21 /* Ethernet */ -#define AT91SAM9260_ID_ISI 22 /* Image Sensor Interface */ -#define AT91SAM9260_ID_US3 23 /* USART 3 */ -#define AT91SAM9260_ID_US4 24 /* USART 4 */ -#define AT91SAM9260_ID_US5 25 /* USART 5 */ -#define AT91SAM9260_ID_TC3 26 /* Timer Counter 3 */ -#define AT91SAM9260_ID_TC4 27 /* Timer Counter 4 */ -#define AT91SAM9260_ID_TC5 28 /* Timer Counter 5 */ -#define AT91SAM9260_ID_IRQ0 29 /* Advanced Interrupt Controller (IRQ0) */ -#define AT91SAM9260_ID_IRQ1 30 /* Advanced Interrupt Controller (IRQ1) */ -#define AT91SAM9260_ID_IRQ2 31 /* Advanced Interrupt Controller (IRQ2) */ - - -/* - * User Peripheral physical base addresses. - */ -#define AT91SAM9260_BASE_TCB0 0xfffa0000 -#define AT91SAM9260_BASE_TC0 0xfffa0000 -#define AT91SAM9260_BASE_TC1 0xfffa0040 -#define AT91SAM9260_BASE_TC2 0xfffa0080 -#define AT91SAM9260_BASE_UDP 0xfffa4000 -#define AT91SAM9260_BASE_MCI 0xfffa8000 -#define AT91SAM9260_BASE_TWI 0xfffac000 -#define AT91SAM9260_BASE_US0 0xfffb0000 -#define AT91SAM9260_BASE_US1 0xfffb4000 -#define AT91SAM9260_BASE_US2 0xfffb8000 -#define AT91SAM9260_BASE_SSC 0xfffbc000 -#define AT91SAM9260_BASE_ISI 0xfffc0000 -#define AT91SAM9260_BASE_EMAC 0xfffc4000 -#define AT91SAM9260_BASE_SPI0 0xfffc8000 -#define AT91SAM9260_BASE_SPI1 0xfffcc000 -#define AT91SAM9260_BASE_US3 0xfffd0000 -#define AT91SAM9260_BASE_US4 0xfffd4000 -#define AT91SAM9260_BASE_US5 0xfffd8000 -#define AT91SAM9260_BASE_TCB1 0xfffdc000 -#define AT91SAM9260_BASE_TC3 0xfffdc000 -#define AT91SAM9260_BASE_TC4 0xfffdc040 -#define AT91SAM9260_BASE_TC5 0xfffdc080 -#define AT91SAM9260_BASE_ADC 0xfffe0000 - -/* - * System Peripherals - */ -#define AT91SAM9260_BASE_ECC 0xffffe800 -#define AT91SAM9260_BASE_SDRAMC 0xffffea00 -#define AT91SAM9260_BASE_SMC 0xffffec00 -#define AT91SAM9260_BASE_MATRIX 0xffffee00 -#define AT91SAM9260_BASE_DBGU AT91_BASE_DBGU0 -#define AT91SAM9260_BASE_PIOA 0xfffff400 -#define AT91SAM9260_BASE_PIOB 0xfffff600 -#define AT91SAM9260_BASE_PIOC 0xfffff800 -#define AT91SAM9260_BASE_RSTC 0xfffffd00 -#define AT91SAM9260_BASE_SHDWC 0xfffffd10 -#define AT91SAM9260_BASE_RTT 0xfffffd20 -#define AT91SAM9260_BASE_PIT 0xfffffd30 -#define AT91SAM9260_BASE_WDT 0xfffffd40 -#define AT91SAM9260_BASE_GPBR 0xfffffd50 - - -/* - * Internal Memory. - */ -#define AT91SAM9260_ROM_BASE 0x00100000 /* Internal ROM base address */ -#define AT91SAM9260_ROM_SIZE SZ_32K /* Internal ROM size (32Kb) */ - -#define AT91SAM9260_SRAM0_BASE 0x00200000 /* Internal SRAM 0 base address */ -#define AT91SAM9260_SRAM0_SIZE SZ_4K /* Internal SRAM 0 size (4Kb) */ -#define AT91SAM9260_SRAM1_BASE 0x00300000 /* Internal SRAM 1 base address */ -#define AT91SAM9260_SRAM1_SIZE SZ_4K /* Internal SRAM 1 size (4Kb) */ -#define AT91SAM9260_SRAM_BASE 0x002FF000 /* Internal SRAM base address */ -#define AT91SAM9260_SRAM_SIZE SZ_8K /* Internal SRAM size (8Kb) */ - -#define AT91SAM9260_UHP_BASE 0x00500000 /* USB Host controller */ - -#define AT91SAM9XE_FLASH_BASE 0x00200000 /* Internal FLASH base address */ -#define AT91SAM9XE_SRAM_BASE 0x00300000 /* Internal SRAM base address */ - -#define AT91SAM9G20_ROM_BASE 0x00100000 /* Internal ROM base address */ -#define AT91SAM9G20_ROM_SIZE SZ_32K /* Internal ROM size (32Kb) */ - -#define AT91SAM9G20_SRAM0_BASE 0x00200000 /* Internal SRAM 0 base address */ -#define AT91SAM9G20_SRAM0_SIZE SZ_16K /* Internal SRAM 0 size (16Kb) */ -#define AT91SAM9G20_SRAM1_BASE 0x00300000 /* Internal SRAM 1 base address */ -#define AT91SAM9G20_SRAM1_SIZE SZ_16K /* Internal SRAM 1 size (16Kb) */ -#define AT91SAM9G20_SRAM_BASE 0x002FC000 /* Internal SRAM base address */ -#define AT91SAM9G20_SRAM_SIZE SZ_32K /* Internal SRAM size (32Kb) */ - -#define AT91SAM9G20_UHP_BASE 0x00500000 /* USB Host controller */ - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9260_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9260_matrix.h deleted file mode 100644 index f459df420629..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9260_matrix.h +++ /dev/null @@ -1,80 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/at91sam9260_matrix.h - * - * Copyright (C) 2007 Atmel Corporation. - * - * Memory Controllers (MATRIX, EBI) - System peripherals registers. - * Based on AT91SAM9260 datasheet revision B. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91SAM9260_MATRIX_H -#define AT91SAM9260_MATRIX_H - -#define AT91_MATRIX_MCFG0 0x00 /* Master Configuration Register 0 */ -#define AT91_MATRIX_MCFG1 0x04 /* Master Configuration Register 1 */ -#define AT91_MATRIX_MCFG2 0x08 /* Master Configuration Register 2 */ -#define AT91_MATRIX_MCFG3 0x0C /* Master Configuration Register 3 */ -#define AT91_MATRIX_MCFG4 0x10 /* Master Configuration Register 4 */ -#define AT91_MATRIX_MCFG5 0x14 /* Master Configuration Register 5 */ -#define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */ -#define AT91_MATRIX_ULBT_INFINITE (0 << 0) -#define AT91_MATRIX_ULBT_SINGLE (1 << 0) -#define AT91_MATRIX_ULBT_FOUR (2 << 0) -#define AT91_MATRIX_ULBT_EIGHT (3 << 0) -#define AT91_MATRIX_ULBT_SIXTEEN (4 << 0) - -#define AT91_MATRIX_SCFG0 0x40 /* Slave Configuration Register 0 */ -#define AT91_MATRIX_SCFG1 0x44 /* Slave Configuration Register 1 */ -#define AT91_MATRIX_SCFG2 0x48 /* Slave Configuration Register 2 */ -#define AT91_MATRIX_SCFG3 0x4C /* Slave Configuration Register 3 */ -#define AT91_MATRIX_SCFG4 0x50 /* Slave Configuration Register 4 */ -#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */ -#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */ -#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_LAST (1 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16) -#define AT91_MATRIX_FIXED_DEFMSTR (7 << 18) /* Fixed Index of Default Master */ -#define AT91_MATRIX_ARBT (3 << 24) /* Arbitration Type */ -#define AT91_MATRIX_ARBT_ROUND_ROBIN (0 << 24) -#define AT91_MATRIX_ARBT_FIXED_PRIORITY (1 << 24) - -#define AT91_MATRIX_PRAS0 0x80 /* Priority Register A for Slave 0 */ -#define AT91_MATRIX_PRAS1 0x88 /* Priority Register A for Slave 1 */ -#define AT91_MATRIX_PRAS2 0x90 /* Priority Register A for Slave 2 */ -#define AT91_MATRIX_PRAS3 0x98 /* Priority Register A for Slave 3 */ -#define AT91_MATRIX_PRAS4 0xA0 /* Priority Register A for Slave 4 */ -#define AT91_MATRIX_M0PR (3 << 0) /* Master 0 Priority */ -#define AT91_MATRIX_M1PR (3 << 4) /* Master 1 Priority */ -#define AT91_MATRIX_M2PR (3 << 8) /* Master 2 Priority */ -#define AT91_MATRIX_M3PR (3 << 12) /* Master 3 Priority */ -#define AT91_MATRIX_M4PR (3 << 16) /* Master 4 Priority */ -#define AT91_MATRIX_M5PR (3 << 20) /* Master 5 Priority */ - -#define AT91_MATRIX_MRCR 0x100 /* Master Remap Control Register */ -#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */ -#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */ - -#define AT91_MATRIX_EBICSA 0x11C /* EBI Chip Select Assignment Register */ -#define AT91_MATRIX_CS1A (1 << 1) /* Chip Select 1 Assignment */ -#define AT91_MATRIX_CS1A_SMC (0 << 1) -#define AT91_MATRIX_CS1A_SDRAMC (1 << 1) -#define AT91_MATRIX_CS3A (1 << 3) /* Chip Select 3 Assignment */ -#define AT91_MATRIX_CS3A_SMC (0 << 3) -#define AT91_MATRIX_CS3A_SMC_SMARTMEDIA (1 << 3) -#define AT91_MATRIX_CS4A (1 << 4) /* Chip Select 4 Assignment */ -#define AT91_MATRIX_CS4A_SMC (0 << 4) -#define AT91_MATRIX_CS4A_SMC_CF1 (1 << 4) -#define AT91_MATRIX_CS5A (1 << 5) /* Chip Select 5 Assignment */ -#define AT91_MATRIX_CS5A_SMC (0 << 5) -#define AT91_MATRIX_CS5A_SMC_CF2 (1 << 5) -#define AT91_MATRIX_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ -#define AT91_MATRIX_VDDIOMSEL (1 << 16) /* Memory voltage selection */ -#define AT91_MATRIX_VDDIOMSEL_1_8V (0 << 16) -#define AT91_MATRIX_VDDIOMSEL_3_3V (1 << 16) - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9261.h b/arch/arm/mach-at91/include/mach/at91sam9261.h deleted file mode 100644 index a041406d06ee..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9261.h +++ /dev/null @@ -1,99 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/at91sam9261.h - * - * Copyright (C) SAN People - * - * Common definitions. - * Based on AT91SAM9261 datasheet revision E. (Preliminary) - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91SAM9261_H -#define AT91SAM9261_H - -/* - * Peripheral identifiers/interrupts. - */ -#define AT91SAM9261_ID_PIOA 2 /* Parallel IO Controller A */ -#define AT91SAM9261_ID_PIOB 3 /* Parallel IO Controller B */ -#define AT91SAM9261_ID_PIOC 4 /* Parallel IO Controller C */ -#define AT91SAM9261_ID_US0 6 /* USART 0 */ -#define AT91SAM9261_ID_US1 7 /* USART 1 */ -#define AT91SAM9261_ID_US2 8 /* USART 2 */ -#define AT91SAM9261_ID_MCI 9 /* Multimedia Card Interface */ -#define AT91SAM9261_ID_UDP 10 /* USB Device Port */ -#define AT91SAM9261_ID_TWI 11 /* Two-Wire Interface */ -#define AT91SAM9261_ID_SPI0 12 /* Serial Peripheral Interface 0 */ -#define AT91SAM9261_ID_SPI1 13 /* Serial Peripheral Interface 1 */ -#define AT91SAM9261_ID_SSC0 14 /* Serial Synchronous Controller 0 */ -#define AT91SAM9261_ID_SSC1 15 /* Serial Synchronous Controller 1 */ -#define AT91SAM9261_ID_SSC2 16 /* Serial Synchronous Controller 2 */ -#define AT91SAM9261_ID_TC0 17 /* Timer Counter 0 */ -#define AT91SAM9261_ID_TC1 18 /* Timer Counter 1 */ -#define AT91SAM9261_ID_TC2 19 /* Timer Counter 2 */ -#define AT91SAM9261_ID_UHP 20 /* USB Host port */ -#define AT91SAM9261_ID_LCDC 21 /* LDC Controller */ -#define AT91SAM9261_ID_IRQ0 29 /* Advanced Interrupt Controller (IRQ0) */ -#define AT91SAM9261_ID_IRQ1 30 /* Advanced Interrupt Controller (IRQ1) */ -#define AT91SAM9261_ID_IRQ2 31 /* Advanced Interrupt Controller (IRQ2) */ - - -/* - * User Peripheral physical base addresses. - */ -#define AT91SAM9261_BASE_TCB0 0xfffa0000 -#define AT91SAM9261_BASE_TC0 0xfffa0000 -#define AT91SAM9261_BASE_TC1 0xfffa0040 -#define AT91SAM9261_BASE_TC2 0xfffa0080 -#define AT91SAM9261_BASE_UDP 0xfffa4000 -#define AT91SAM9261_BASE_MCI 0xfffa8000 -#define AT91SAM9261_BASE_TWI 0xfffac000 -#define AT91SAM9261_BASE_US0 0xfffb0000 -#define AT91SAM9261_BASE_US1 0xfffb4000 -#define AT91SAM9261_BASE_US2 0xfffb8000 -#define AT91SAM9261_BASE_SSC0 0xfffbc000 -#define AT91SAM9261_BASE_SSC1 0xfffc0000 -#define AT91SAM9261_BASE_SSC2 0xfffc4000 -#define AT91SAM9261_BASE_SPI0 0xfffc8000 -#define AT91SAM9261_BASE_SPI1 0xfffcc000 - - -/* - * System Peripherals - */ -#define AT91SAM9261_BASE_SMC 0xffffec00 -#define AT91SAM9261_BASE_MATRIX 0xffffee00 -#define AT91SAM9261_BASE_SDRAMC 0xffffea00 -#define AT91SAM9261_BASE_DBGU AT91_BASE_DBGU0 -#define AT91SAM9261_BASE_PIOA 0xfffff400 -#define AT91SAM9261_BASE_PIOB 0xfffff600 -#define AT91SAM9261_BASE_PIOC 0xfffff800 -#define AT91SAM9261_BASE_RSTC 0xfffffd00 -#define AT91SAM9261_BASE_SHDWC 0xfffffd10 -#define AT91SAM9261_BASE_RTT 0xfffffd20 -#define AT91SAM9261_BASE_PIT 0xfffffd30 -#define AT91SAM9261_BASE_WDT 0xfffffd40 -#define AT91SAM9261_BASE_GPBR 0xfffffd50 - - -/* - * Internal Memory. - */ -#define AT91SAM9261_SRAM_BASE 0x00300000 /* Internal SRAM base address */ -#define AT91SAM9261_SRAM_SIZE 0x00028000 /* Internal SRAM size (160Kb) */ - -#define AT91SAM9G10_SRAM_BASE AT91SAM9261_SRAM_BASE /* Internal SRAM base address */ -#define AT91SAM9G10_SRAM_SIZE 0x00004000 /* Internal SRAM size (16Kb) */ - -#define AT91SAM9261_ROM_BASE 0x00400000 /* Internal ROM base address */ -#define AT91SAM9261_ROM_SIZE SZ_32K /* Internal ROM size (32Kb) */ - -#define AT91SAM9261_UHP_BASE 0x00500000 /* USB Host controller */ -#define AT91SAM9261_LCDC_BASE 0x00600000 /* LDC controller */ - - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9261_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9261_matrix.h deleted file mode 100644 index a50cdf8b8ca4..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9261_matrix.h +++ /dev/null @@ -1,64 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/at91sam9261_matrix.h - * - * Copyright (C) 2007 Atmel Corporation. - * - * Memory Controllers (MATRIX, EBI) - System peripherals registers. - * Based on AT91SAM9261 datasheet revision D. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91SAM9261_MATRIX_H -#define AT91SAM9261_MATRIX_H - -#define AT91_MATRIX_MCFG 0x00 /* Master Configuration Register */ -#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */ -#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */ - -#define AT91_MATRIX_SCFG0 0x04 /* Slave Configuration Register 0 */ -#define AT91_MATRIX_SCFG1 0x08 /* Slave Configuration Register 1 */ -#define AT91_MATRIX_SCFG2 0x0C /* Slave Configuration Register 2 */ -#define AT91_MATRIX_SCFG3 0x10 /* Slave Configuration Register 3 */ -#define AT91_MATRIX_SCFG4 0x14 /* Slave Configuration Register 4 */ -#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */ -#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */ -#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_LAST (1 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16) -#define AT91_MATRIX_FIXED_DEFMSTR (7 << 18) /* Fixed Index of Default Master */ - -#define AT91_MATRIX_TCR 0x24 /* TCM Configuration Register */ -#define AT91_MATRIX_ITCM_SIZE (0xf << 0) /* Size of ITCM enabled memory block */ -#define AT91_MATRIX_ITCM_0 (0 << 0) -#define AT91_MATRIX_ITCM_16 (5 << 0) -#define AT91_MATRIX_ITCM_32 (6 << 0) -#define AT91_MATRIX_ITCM_64 (7 << 0) -#define AT91_MATRIX_DTCM_SIZE (0xf << 4) /* Size of DTCM enabled memory block */ -#define AT91_MATRIX_DTCM_0 (0 << 4) -#define AT91_MATRIX_DTCM_16 (5 << 4) -#define AT91_MATRIX_DTCM_32 (6 << 4) -#define AT91_MATRIX_DTCM_64 (7 << 4) - -#define AT91_MATRIX_EBICSA 0x30 /* EBI Chip Select Assignment Register */ -#define AT91_MATRIX_CS1A (1 << 1) /* Chip Select 1 Assignment */ -#define AT91_MATRIX_CS1A_SMC (0 << 1) -#define AT91_MATRIX_CS1A_SDRAMC (1 << 1) -#define AT91_MATRIX_CS3A (1 << 3) /* Chip Select 3 Assignment */ -#define AT91_MATRIX_CS3A_SMC (0 << 3) -#define AT91_MATRIX_CS3A_SMC_SMARTMEDIA (1 << 3) -#define AT91_MATRIX_CS4A (1 << 4) /* Chip Select 4 Assignment */ -#define AT91_MATRIX_CS4A_SMC (0 << 4) -#define AT91_MATRIX_CS4A_SMC_CF1 (1 << 4) -#define AT91_MATRIX_CS5A (1 << 5) /* Chip Select 5 Assignment */ -#define AT91_MATRIX_CS5A_SMC (0 << 5) -#define AT91_MATRIX_CS5A_SMC_CF2 (1 << 5) -#define AT91_MATRIX_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ - -#define AT91_MATRIX_USBPUCR 0x34 /* USB Pad Pull-Up Control Register */ -#define AT91_MATRIX_USBPUCR_PUON (1 << 30) /* USB Device PAD Pull-up Enable */ - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9263.h b/arch/arm/mach-at91/include/mach/at91sam9263.h deleted file mode 100644 index d201029d60b3..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9263.h +++ /dev/null @@ -1,117 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/at91sam9263.h - * - * (C) 2007 Atmel Corporation. - * - * Common definitions. - * Based on AT91SAM9263 datasheet revision B (Preliminary). - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91SAM9263_H -#define AT91SAM9263_H - -/* - * Peripheral identifiers/interrupts. - */ -#define AT91SAM9263_ID_PIOA 2 /* Parallel IO Controller A */ -#define AT91SAM9263_ID_PIOB 3 /* Parallel IO Controller B */ -#define AT91SAM9263_ID_PIOCDE 4 /* Parallel IO Controller C, D and E */ -#define AT91SAM9263_ID_US0 7 /* USART 0 */ -#define AT91SAM9263_ID_US1 8 /* USART 1 */ -#define AT91SAM9263_ID_US2 9 /* USART 2 */ -#define AT91SAM9263_ID_MCI0 10 /* Multimedia Card Interface 0 */ -#define AT91SAM9263_ID_MCI1 11 /* Multimedia Card Interface 1 */ -#define AT91SAM9263_ID_CAN 12 /* CAN */ -#define AT91SAM9263_ID_TWI 13 /* Two-Wire Interface */ -#define AT91SAM9263_ID_SPI0 14 /* Serial Peripheral Interface 0 */ -#define AT91SAM9263_ID_SPI1 15 /* Serial Peripheral Interface 1 */ -#define AT91SAM9263_ID_SSC0 16 /* Serial Synchronous Controller 0 */ -#define AT91SAM9263_ID_SSC1 17 /* Serial Synchronous Controller 1 */ -#define AT91SAM9263_ID_AC97C 18 /* AC97 Controller */ -#define AT91SAM9263_ID_TCB 19 /* Timer Counter 0, 1 and 2 */ -#define AT91SAM9263_ID_PWMC 20 /* Pulse Width Modulation Controller */ -#define AT91SAM9263_ID_EMAC 21 /* Ethernet */ -#define AT91SAM9263_ID_2DGE 23 /* 2D Graphic Engine */ -#define AT91SAM9263_ID_UDP 24 /* USB Device Port */ -#define AT91SAM9263_ID_ISI 25 /* Image Sensor Interface */ -#define AT91SAM9263_ID_LCDC 26 /* LCD Controller */ -#define AT91SAM9263_ID_DMA 27 /* DMA Controller */ -#define AT91SAM9263_ID_UHP 29 /* USB Host port */ -#define AT91SAM9263_ID_IRQ0 30 /* Advanced Interrupt Controller (IRQ0) */ -#define AT91SAM9263_ID_IRQ1 31 /* Advanced Interrupt Controller (IRQ1) */ - - -/* - * User Peripheral physical base addresses. - */ -#define AT91SAM9263_BASE_UDP 0xfff78000 -#define AT91SAM9263_BASE_TCB0 0xfff7c000 -#define AT91SAM9263_BASE_TC0 0xfff7c000 -#define AT91SAM9263_BASE_TC1 0xfff7c040 -#define AT91SAM9263_BASE_TC2 0xfff7c080 -#define AT91SAM9263_BASE_MCI0 0xfff80000 -#define AT91SAM9263_BASE_MCI1 0xfff84000 -#define AT91SAM9263_BASE_TWI 0xfff88000 -#define AT91SAM9263_BASE_US0 0xfff8c000 -#define AT91SAM9263_BASE_US1 0xfff90000 -#define AT91SAM9263_BASE_US2 0xfff94000 -#define AT91SAM9263_BASE_SSC0 0xfff98000 -#define AT91SAM9263_BASE_SSC1 0xfff9c000 -#define AT91SAM9263_BASE_AC97C 0xfffa0000 -#define AT91SAM9263_BASE_SPI0 0xfffa4000 -#define AT91SAM9263_BASE_SPI1 0xfffa8000 -#define AT91SAM9263_BASE_CAN 0xfffac000 -#define AT91SAM9263_BASE_PWMC 0xfffb8000 -#define AT91SAM9263_BASE_EMAC 0xfffbc000 -#define AT91SAM9263_BASE_ISI 0xfffc4000 -#define AT91SAM9263_BASE_2DGE 0xfffc8000 - -/* - * System Peripherals - */ -#define AT91SAM9263_BASE_ECC0 0xffffe000 -#define AT91SAM9263_BASE_SDRAMC0 0xffffe200 -#define AT91SAM9263_BASE_SMC0 0xffffe400 -#define AT91SAM9263_BASE_ECC1 0xffffe600 -#define AT91SAM9263_BASE_SDRAMC1 0xffffe800 -#define AT91SAM9263_BASE_SMC1 0xffffea00 -#define AT91SAM9263_BASE_MATRIX 0xffffec00 -#define AT91SAM9263_BASE_DBGU AT91_BASE_DBGU1 -#define AT91SAM9263_BASE_PIOA 0xfffff200 -#define AT91SAM9263_BASE_PIOB 0xfffff400 -#define AT91SAM9263_BASE_PIOC 0xfffff600 -#define AT91SAM9263_BASE_PIOD 0xfffff800 -#define AT91SAM9263_BASE_PIOE 0xfffffa00 -#define AT91SAM9263_BASE_RSTC 0xfffffd00 -#define AT91SAM9263_BASE_SHDWC 0xfffffd10 -#define AT91SAM9263_BASE_RTT0 0xfffffd20 -#define AT91SAM9263_BASE_PIT 0xfffffd30 -#define AT91SAM9263_BASE_WDT 0xfffffd40 -#define AT91SAM9263_BASE_RTT1 0xfffffd50 -#define AT91SAM9263_BASE_GPBR 0xfffffd60 - -#define AT91_SMC AT91_SMC0 - -/* - * Internal Memory. - */ -#define AT91SAM9263_SRAM0_BASE 0x00300000 /* Internal SRAM 0 base address */ -#define AT91SAM9263_SRAM0_SIZE (80 * SZ_1K) /* Internal SRAM 0 size (80Kb) */ - -#define AT91SAM9263_ROM_BASE 0x00400000 /* Internal ROM base address */ -#define AT91SAM9263_ROM_SIZE SZ_128K /* Internal ROM size (128Kb) */ - -#define AT91SAM9263_SRAM1_BASE 0x00500000 /* Internal SRAM 1 base address */ -#define AT91SAM9263_SRAM1_SIZE SZ_16K /* Internal SRAM 1 size (16Kb) */ - -#define AT91SAM9263_LCDC_BASE 0x00700000 /* LCD Controller */ -#define AT91SAM9263_DMAC_BASE 0x00800000 /* DMA Controller */ -#define AT91SAM9263_UHP_BASE 0x00a00000 /* USB Host controller */ - - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9263_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9263_matrix.h deleted file mode 100644 index ebb5fdb565e0..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9263_matrix.h +++ /dev/null @@ -1,129 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/at91sam9263_matrix.h - * - * Copyright (C) 2006 Atmel Corporation. - * - * Memory Controllers (MATRIX, EBI) - System peripherals registers. - * Based on AT91SAM9263 datasheet revision B (Preliminary). - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91SAM9263_MATRIX_H -#define AT91SAM9263_MATRIX_H - -#define AT91_MATRIX_MCFG0 0x00 /* Master Configuration Register 0 */ -#define AT91_MATRIX_MCFG1 0x04 /* Master Configuration Register 1 */ -#define AT91_MATRIX_MCFG2 0x08 /* Master Configuration Register 2 */ -#define AT91_MATRIX_MCFG3 0x0C /* Master Configuration Register 3 */ -#define AT91_MATRIX_MCFG4 0x10 /* Master Configuration Register 4 */ -#define AT91_MATRIX_MCFG5 0x14 /* Master Configuration Register 5 */ -#define AT91_MATRIX_MCFG6 0x18 /* Master Configuration Register 6 */ -#define AT91_MATRIX_MCFG7 0x1C /* Master Configuration Register 7 */ -#define AT91_MATRIX_MCFG8 0x20 /* Master Configuration Register 8 */ -#define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */ -#define AT91_MATRIX_ULBT_INFINITE (0 << 0) -#define AT91_MATRIX_ULBT_SINGLE (1 << 0) -#define AT91_MATRIX_ULBT_FOUR (2 << 0) -#define AT91_MATRIX_ULBT_EIGHT (3 << 0) -#define AT91_MATRIX_ULBT_SIXTEEN (4 << 0) - -#define AT91_MATRIX_SCFG0 0x40 /* Slave Configuration Register 0 */ -#define AT91_MATRIX_SCFG1 0x44 /* Slave Configuration Register 1 */ -#define AT91_MATRIX_SCFG2 0x48 /* Slave Configuration Register 2 */ -#define AT91_MATRIX_SCFG3 0x4C /* Slave Configuration Register 3 */ -#define AT91_MATRIX_SCFG4 0x50 /* Slave Configuration Register 4 */ -#define AT91_MATRIX_SCFG5 0x54 /* Slave Configuration Register 5 */ -#define AT91_MATRIX_SCFG6 0x58 /* Slave Configuration Register 6 */ -#define AT91_MATRIX_SCFG7 0x5C /* Slave Configuration Register 7 */ -#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */ -#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */ -#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_LAST (1 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16) -#define AT91_MATRIX_FIXED_DEFMSTR (0xf << 18) /* Fixed Index of Default Master */ -#define AT91_MATRIX_ARBT (3 << 24) /* Arbitration Type */ -#define AT91_MATRIX_ARBT_ROUND_ROBIN (0 << 24) -#define AT91_MATRIX_ARBT_FIXED_PRIORITY (1 << 24) - -#define AT91_MATRIX_PRAS0 0x80 /* Priority Register A for Slave 0 */ -#define AT91_MATRIX_PRBS0 0x84 /* Priority Register B for Slave 0 */ -#define AT91_MATRIX_PRAS1 0x88 /* Priority Register A for Slave 1 */ -#define AT91_MATRIX_PRBS1 0x8C /* Priority Register B for Slave 1 */ -#define AT91_MATRIX_PRAS2 0x90 /* Priority Register A for Slave 2 */ -#define AT91_MATRIX_PRBS2 0x94 /* Priority Register B for Slave 2 */ -#define AT91_MATRIX_PRAS3 0x98 /* Priority Register A for Slave 3 */ -#define AT91_MATRIX_PRBS3 0x9C /* Priority Register B for Slave 3 */ -#define AT91_MATRIX_PRAS4 0xA0 /* Priority Register A for Slave 4 */ -#define AT91_MATRIX_PRBS4 0xA4 /* Priority Register B for Slave 4 */ -#define AT91_MATRIX_PRAS5 0xA8 /* Priority Register A for Slave 5 */ -#define AT91_MATRIX_PRBS5 0xAC /* Priority Register B for Slave 5 */ -#define AT91_MATRIX_PRAS6 0xB0 /* Priority Register A for Slave 6 */ -#define AT91_MATRIX_PRBS6 0xB4 /* Priority Register B for Slave 6 */ -#define AT91_MATRIX_PRAS7 0xB8 /* Priority Register A for Slave 7 */ -#define AT91_MATRIX_PRBS7 0xBC /* Priority Register B for Slave 7 */ -#define AT91_MATRIX_M0PR (3 << 0) /* Master 0 Priority */ -#define AT91_MATRIX_M1PR (3 << 4) /* Master 1 Priority */ -#define AT91_MATRIX_M2PR (3 << 8) /* Master 2 Priority */ -#define AT91_MATRIX_M3PR (3 << 12) /* Master 3 Priority */ -#define AT91_MATRIX_M4PR (3 << 16) /* Master 4 Priority */ -#define AT91_MATRIX_M5PR (3 << 20) /* Master 5 Priority */ -#define AT91_MATRIX_M6PR (3 << 24) /* Master 6 Priority */ -#define AT91_MATRIX_M7PR (3 << 28) /* Master 7 Priority */ -#define AT91_MATRIX_M8PR (3 << 0) /* Master 8 Priority (in Register B) */ - -#define AT91_MATRIX_MRCR 0x100 /* Master Remap Control Register */ -#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */ -#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */ -#define AT91_MATRIX_RCB2 (1 << 2) -#define AT91_MATRIX_RCB3 (1 << 3) -#define AT91_MATRIX_RCB4 (1 << 4) -#define AT91_MATRIX_RCB5 (1 << 5) -#define AT91_MATRIX_RCB6 (1 << 6) -#define AT91_MATRIX_RCB7 (1 << 7) -#define AT91_MATRIX_RCB8 (1 << 8) - -#define AT91_MATRIX_TCMR 0x114 /* TCM Configuration Register */ -#define AT91_MATRIX_ITCM_SIZE (0xf << 0) /* Size of ITCM enabled memory block */ -#define AT91_MATRIX_ITCM_0 (0 << 0) -#define AT91_MATRIX_ITCM_16 (5 << 0) -#define AT91_MATRIX_ITCM_32 (6 << 0) -#define AT91_MATRIX_DTCM_SIZE (0xf << 4) /* Size of DTCM enabled memory block */ -#define AT91_MATRIX_DTCM_0 (0 << 4) -#define AT91_MATRIX_DTCM_16 (5 << 4) -#define AT91_MATRIX_DTCM_32 (6 << 4) - -#define AT91_MATRIX_EBI0CSA 0x120 /* EBI0 Chip Select Assignment Register */ -#define AT91_MATRIX_EBI0_CS1A (1 << 1) /* Chip Select 1 Assignment */ -#define AT91_MATRIX_EBI0_CS1A_SMC (0 << 1) -#define AT91_MATRIX_EBI0_CS1A_SDRAMC (1 << 1) -#define AT91_MATRIX_EBI0_CS3A (1 << 3) /* Chip Select 3 Assignment */ -#define AT91_MATRIX_EBI0_CS3A_SMC (0 << 3) -#define AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA (1 << 3) -#define AT91_MATRIX_EBI0_CS4A (1 << 4) /* Chip Select 4 Assignment */ -#define AT91_MATRIX_EBI0_CS4A_SMC (0 << 4) -#define AT91_MATRIX_EBI0_CS4A_SMC_CF1 (1 << 4) -#define AT91_MATRIX_EBI0_CS5A (1 << 5) /* Chip Select 5 Assignment */ -#define AT91_MATRIX_EBI0_CS5A_SMC (0 << 5) -#define AT91_MATRIX_EBI0_CS5A_SMC_CF2 (1 << 5) -#define AT91_MATRIX_EBI0_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ -#define AT91_MATRIX_EBI0_VDDIOMSEL (1 << 16) /* Memory voltage selection */ -#define AT91_MATRIX_EBI0_VDDIOMSEL_1_8V (0 << 16) -#define AT91_MATRIX_EBI0_VDDIOMSEL_3_3V (1 << 16) - -#define AT91_MATRIX_EBI1CSA 0x124 /* EBI1 Chip Select Assignment Register */ -#define AT91_MATRIX_EBI1_CS1A (1 << 1) /* Chip Select 1 Assignment */ -#define AT91_MATRIX_EBI1_CS1A_SMC (0 << 1) -#define AT91_MATRIX_EBI1_CS1A_SDRAMC (1 << 1) -#define AT91_MATRIX_EBI1_CS2A (1 << 3) /* Chip Select 3 Assignment */ -#define AT91_MATRIX_EBI1_CS2A_SMC (0 << 3) -#define AT91_MATRIX_EBI1_CS2A_SMC_SMARTMEDIA (1 << 3) -#define AT91_MATRIX_EBI1_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ -#define AT91_MATRIX_EBI1_VDDIOMSEL (1 << 16) /* Memory voltage selection */ -#define AT91_MATRIX_EBI1_VDDIOMSEL_1_8V (0 << 16) -#define AT91_MATRIX_EBI1_VDDIOMSEL_3_3V (1 << 16) - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9_smc.h b/arch/arm/mach-at91/include/mach/at91sam9_smc.h index 175e1fdd9fe8..ff54a0ce90e3 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9_smc.h +++ b/arch/arm/mach-at91/include/mach/at91sam9_smc.h @@ -16,8 +16,6 @@ #ifndef AT91SAM9_SMC_H #define AT91SAM9_SMC_H -#include - #ifndef __ASSEMBLY__ struct sam9_smc_config { /* Setup register */ diff --git a/arch/arm/mach-at91/include/mach/at91sam9g45.h b/arch/arm/mach-at91/include/mach/at91sam9g45.h deleted file mode 100644 index 8eba1021f533..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9g45.h +++ /dev/null @@ -1,143 +0,0 @@ -/* - * Chip-specific header file for the AT91SAM9G45 family - * - * Copyright (C) 2008-2009 Atmel Corporation. - * - * Common definitions. - * Based on AT91SAM9G45 preliminary datasheet. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91SAM9G45_H -#define AT91SAM9G45_H - -/* - * Peripheral identifiers/interrupts. - */ -#define AT91SAM9G45_ID_PIOA 2 /* Parallel I/O Controller A */ -#define AT91SAM9G45_ID_PIOB 3 /* Parallel I/O Controller B */ -#define AT91SAM9G45_ID_PIOC 4 /* Parallel I/O Controller C */ -#define AT91SAM9G45_ID_PIODE 5 /* Parallel I/O Controller D and E */ -#define AT91SAM9G45_ID_TRNG 6 /* True Random Number Generator */ -#define AT91SAM9G45_ID_US0 7 /* USART 0 */ -#define AT91SAM9G45_ID_US1 8 /* USART 1 */ -#define AT91SAM9G45_ID_US2 9 /* USART 2 */ -#define AT91SAM9G45_ID_US3 10 /* USART 3 */ -#define AT91SAM9G45_ID_MCI0 11 /* High Speed Multimedia Card Interface 0 */ -#define AT91SAM9G45_ID_TWI0 12 /* Two-Wire Interface 0 */ -#define AT91SAM9G45_ID_TWI1 13 /* Two-Wire Interface 1 */ -#define AT91SAM9G45_ID_SPI0 14 /* Serial Peripheral Interface 0 */ -#define AT91SAM9G45_ID_SPI1 15 /* Serial Peripheral Interface 1 */ -#define AT91SAM9G45_ID_SSC0 16 /* Synchronous Serial Controller 0 */ -#define AT91SAM9G45_ID_SSC1 17 /* Synchronous Serial Controller 1 */ -#define AT91SAM9G45_ID_TCB 18 /* Timer Counter 0, 1, 2, 3, 4 and 5 */ -#define AT91SAM9G45_ID_PWMC 19 /* Pulse Width Modulation Controller */ -#define AT91SAM9G45_ID_TSC 20 /* Touch Screen ADC Controller */ -#define AT91SAM9G45_ID_DMA 21 /* DMA Controller */ -#define AT91SAM9G45_ID_UHPHS 22 /* USB Host High Speed */ -#define AT91SAM9G45_ID_LCDC 23 /* LCD Controller */ -#define AT91SAM9G45_ID_AC97C 24 /* AC97 Controller */ -#define AT91SAM9G45_ID_EMAC 25 /* Ethernet MAC */ -#define AT91SAM9G45_ID_ISI 26 /* Image Sensor Interface */ -#define AT91SAM9G45_ID_UDPHS 27 /* USB Device High Speed */ -#define AT91SAM9G45_ID_AESTDESSHA 28 /* AES + T-DES + SHA */ -#define AT91SAM9G45_ID_MCI1 29 /* High Speed Multimedia Card Interface 1 */ -#define AT91SAM9G45_ID_VDEC 30 /* Video Decoder */ -#define AT91SAM9G45_ID_IRQ0 31 /* Advanced Interrupt Controller */ - -/* - * User Peripheral physical base addresses. - */ -#define AT91SAM9G45_BASE_UDPHS 0xfff78000 -#define AT91SAM9G45_BASE_TCB0 0xfff7c000 -#define AT91SAM9G45_BASE_TC0 0xfff7c000 -#define AT91SAM9G45_BASE_TC1 0xfff7c040 -#define AT91SAM9G45_BASE_TC2 0xfff7c080 -#define AT91SAM9G45_BASE_MCI0 0xfff80000 -#define AT91SAM9G45_BASE_TWI0 0xfff84000 -#define AT91SAM9G45_BASE_TWI1 0xfff88000 -#define AT91SAM9G45_BASE_US0 0xfff8c000 -#define AT91SAM9G45_BASE_US1 0xfff90000 -#define AT91SAM9G45_BASE_US2 0xfff94000 -#define AT91SAM9G45_BASE_US3 0xfff98000 -#define AT91SAM9G45_BASE_SSC0 0xfff9c000 -#define AT91SAM9G45_BASE_SSC1 0xfffa0000 -#define AT91SAM9G45_BASE_SPI0 0xfffa4000 -#define AT91SAM9G45_BASE_SPI1 0xfffa8000 -#define AT91SAM9G45_BASE_AC97C 0xfffac000 -#define AT91SAM9G45_BASE_TSC 0xfffb0000 -#define AT91SAM9G45_BASE_ISI 0xfffb4000 -#define AT91SAM9G45_BASE_PWMC 0xfffb8000 -#define AT91SAM9G45_BASE_EMAC 0xfffbc000 -#define AT91SAM9G45_BASE_AES 0xfffc0000 -#define AT91SAM9G45_BASE_TDES 0xfffc4000 -#define AT91SAM9G45_BASE_SHA 0xfffc8000 -#define AT91SAM9G45_BASE_TRNG 0xfffcc000 -#define AT91SAM9G45_BASE_MCI1 0xfffd0000 -#define AT91SAM9G45_BASE_TCB1 0xfffd4000 -#define AT91SAM9G45_BASE_TC3 0xfffd4000 -#define AT91SAM9G45_BASE_TC4 0xfffd4040 -#define AT91SAM9G45_BASE_TC5 0xfffd4080 - -/* - * System Peripherals - */ -#define AT91SAM9G45_BASE_ECC 0xffffe200 -#define AT91SAM9G45_BASE_DDRSDRC1 0xffffe400 -#define AT91SAM9G45_BASE_DDRSDRC0 0xffffe600 -#define AT91SAM9G45_BASE_DMA 0xffffec00 -#define AT91SAM9G45_BASE_SMC 0xffffe800 -#define AT91SAM9G45_BASE_MATRIX 0xffffea00 -#define AT91SAM9G45_BASE_DBGU AT91_BASE_DBGU1 -#define AT91SAM9G45_BASE_PIOA 0xfffff200 -#define AT91SAM9G45_BASE_PIOB 0xfffff400 -#define AT91SAM9G45_BASE_PIOC 0xfffff600 -#define AT91SAM9G45_BASE_PIOD 0xfffff800 -#define AT91SAM9G45_BASE_PIOE 0xfffffa00 -#define AT91SAM9G45_BASE_RSTC 0xfffffd00 -#define AT91SAM9G45_BASE_SHDWC 0xfffffd10 -#define AT91SAM9G45_BASE_RTT 0xfffffd20 -#define AT91SAM9G45_BASE_PIT 0xfffffd30 -#define AT91SAM9G45_BASE_WDT 0xfffffd40 -#define AT91SAM9G45_BASE_RTC 0xfffffdb0 -#define AT91SAM9G45_BASE_GPBR 0xfffffd60 - -/* - * Internal Memory. - */ -#define AT91SAM9G45_SRAM_BASE 0x00300000 /* Internal SRAM base address */ -#define AT91SAM9G45_SRAM_SIZE SZ_64K /* Internal SRAM size (64Kb) */ - -#define AT91SAM9G45_ROM_BASE 0x00400000 /* Internal ROM base address */ -#define AT91SAM9G45_ROM_SIZE SZ_64K /* Internal ROM size (64Kb) */ - -#define AT91SAM9G45_LCDC_BASE 0x00500000 /* LCD Controller */ -#define AT91SAM9G45_UDPHS_FIFO 0x00600000 /* USB Device HS controller */ -#define AT91SAM9G45_OHCI_BASE 0x00700000 /* USB Host controller (OHCI) */ -#define AT91SAM9G45_EHCI_BASE 0x00800000 /* USB Host controller (EHCI) */ -#define AT91SAM9G45_VDEC_BASE 0x00900000 /* Video Decoder Controller */ - -/* - * DMA peripheral identifiers - * for hardware handshaking interface - */ -#define AT_DMA_ID_MCI0 0 -#define AT_DMA_ID_SPI0_TX 1 -#define AT_DMA_ID_SPI0_RX 2 -#define AT_DMA_ID_SPI1_TX 3 -#define AT_DMA_ID_SPI1_RX 4 -#define AT_DMA_ID_SSC0_TX 5 -#define AT_DMA_ID_SSC0_RX 6 -#define AT_DMA_ID_SSC1_TX 7 -#define AT_DMA_ID_SSC1_RX 8 -#define AT_DMA_ID_AC97_TX 9 -#define AT_DMA_ID_AC97_RX 10 -#define AT_DMA_ID_AES_TX 11 -#define AT_DMA_ID_AES_RX 12 -#define AT_DMA_ID_MCI1 13 - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9g45_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9g45_matrix.h deleted file mode 100644 index b76e2ed2fbc2..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9g45_matrix.h +++ /dev/null @@ -1,153 +0,0 @@ -/* - * Matrix-centric header file for the AT91SAM9G45 family - * - * Copyright (C) 2008-2009 Atmel Corporation. - * - * Memory Controllers (MATRIX, EBI) - System peripherals registers. - * Based on AT91SAM9G45 preliminary datasheet. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91SAM9G45_MATRIX_H -#define AT91SAM9G45_MATRIX_H - -#define AT91_MATRIX_MCFG0 0x00 /* Master Configuration Register 0 */ -#define AT91_MATRIX_MCFG1 0x04 /* Master Configuration Register 1 */ -#define AT91_MATRIX_MCFG2 0x08 /* Master Configuration Register 2 */ -#define AT91_MATRIX_MCFG3 0x0C /* Master Configuration Register 3 */ -#define AT91_MATRIX_MCFG4 0x10 /* Master Configuration Register 4 */ -#define AT91_MATRIX_MCFG5 0x14 /* Master Configuration Register 5 */ -#define AT91_MATRIX_MCFG6 0x18 /* Master Configuration Register 6 */ -#define AT91_MATRIX_MCFG7 0x1C /* Master Configuration Register 7 */ -#define AT91_MATRIX_MCFG8 0x20 /* Master Configuration Register 8 */ -#define AT91_MATRIX_MCFG9 0x24 /* Master Configuration Register 9 */ -#define AT91_MATRIX_MCFG10 0x28 /* Master Configuration Register 10 */ -#define AT91_MATRIX_MCFG11 0x2C /* Master Configuration Register 11 */ -#define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */ -#define AT91_MATRIX_ULBT_INFINITE (0 << 0) -#define AT91_MATRIX_ULBT_SINGLE (1 << 0) -#define AT91_MATRIX_ULBT_FOUR (2 << 0) -#define AT91_MATRIX_ULBT_EIGHT (3 << 0) -#define AT91_MATRIX_ULBT_SIXTEEN (4 << 0) -#define AT91_MATRIX_ULBT_THIRTYTWO (5 << 0) -#define AT91_MATRIX_ULBT_SIXTYFOUR (6 << 0) -#define AT91_MATRIX_ULBT_128 (7 << 0) - -#define AT91_MATRIX_SCFG0 0x40 /* Slave Configuration Register 0 */ -#define AT91_MATRIX_SCFG1 0x44 /* Slave Configuration Register 1 */ -#define AT91_MATRIX_SCFG2 0x48 /* Slave Configuration Register 2 */ -#define AT91_MATRIX_SCFG3 0x4C /* Slave Configuration Register 3 */ -#define AT91_MATRIX_SCFG4 0x50 /* Slave Configuration Register 4 */ -#define AT91_MATRIX_SCFG5 0x54 /* Slave Configuration Register 5 */ -#define AT91_MATRIX_SCFG6 0x58 /* Slave Configuration Register 6 */ -#define AT91_MATRIX_SCFG7 0x5C /* Slave Configuration Register 7 */ -#define AT91_MATRIX_SLOT_CYCLE (0x1ff << 0) /* Maximum Number of Allowed Cycles for a Burst */ -#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */ -#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_LAST (1 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16) -#define AT91_MATRIX_FIXED_DEFMSTR (0xf << 18) /* Fixed Index of Default Master */ - -#define AT91_MATRIX_PRAS0 0x80 /* Priority Register A for Slave 0 */ -#define AT91_MATRIX_PRBS0 0x84 /* Priority Register B for Slave 0 */ -#define AT91_MATRIX_PRAS1 0x88 /* Priority Register A for Slave 1 */ -#define AT91_MATRIX_PRBS1 0x8C /* Priority Register B for Slave 1 */ -#define AT91_MATRIX_PRAS2 0x90 /* Priority Register A for Slave 2 */ -#define AT91_MATRIX_PRBS2 0x94 /* Priority Register B for Slave 2 */ -#define AT91_MATRIX_PRAS3 0x98 /* Priority Register A for Slave 3 */ -#define AT91_MATRIX_PRBS3 0x9C /* Priority Register B for Slave 3 */ -#define AT91_MATRIX_PRAS4 0xA0 /* Priority Register A for Slave 4 */ -#define AT91_MATRIX_PRBS4 0xA4 /* Priority Register B for Slave 4 */ -#define AT91_MATRIX_PRAS5 0xA8 /* Priority Register A for Slave 5 */ -#define AT91_MATRIX_PRBS5 0xAC /* Priority Register B for Slave 5 */ -#define AT91_MATRIX_PRAS6 0xB0 /* Priority Register A for Slave 6 */ -#define AT91_MATRIX_PRBS6 0xB4 /* Priority Register B for Slave 6 */ -#define AT91_MATRIX_PRAS7 0xB8 /* Priority Register A for Slave 7 */ -#define AT91_MATRIX_PRBS7 0xBC /* Priority Register B for Slave 7 */ -#define AT91_MATRIX_M0PR (3 << 0) /* Master 0 Priority */ -#define AT91_MATRIX_M1PR (3 << 4) /* Master 1 Priority */ -#define AT91_MATRIX_M2PR (3 << 8) /* Master 2 Priority */ -#define AT91_MATRIX_M3PR (3 << 12) /* Master 3 Priority */ -#define AT91_MATRIX_M4PR (3 << 16) /* Master 4 Priority */ -#define AT91_MATRIX_M5PR (3 << 20) /* Master 5 Priority */ -#define AT91_MATRIX_M6PR (3 << 24) /* Master 6 Priority */ -#define AT91_MATRIX_M7PR (3 << 28) /* Master 7 Priority */ -#define AT91_MATRIX_M8PR (3 << 0) /* Master 8 Priority (in Register B) */ -#define AT91_MATRIX_M9PR (3 << 4) /* Master 9 Priority (in Register B) */ -#define AT91_MATRIX_M10PR (3 << 8) /* Master 10 Priority (in Register B) */ -#define AT91_MATRIX_M11PR (3 << 12) /* Master 11 Priority (in Register B) */ - -#define AT91_MATRIX_MRCR 0x100 /* Master Remap Control Register */ -#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */ -#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */ -#define AT91_MATRIX_RCB2 (1 << 2) -#define AT91_MATRIX_RCB3 (1 << 3) -#define AT91_MATRIX_RCB4 (1 << 4) -#define AT91_MATRIX_RCB5 (1 << 5) -#define AT91_MATRIX_RCB6 (1 << 6) -#define AT91_MATRIX_RCB7 (1 << 7) -#define AT91_MATRIX_RCB8 (1 << 8) -#define AT91_MATRIX_RCB9 (1 << 9) -#define AT91_MATRIX_RCB10 (1 << 10) -#define AT91_MATRIX_RCB11 (1 << 11) - -#define AT91_MATRIX_TCMR 0x110 /* TCM Configuration Register */ -#define AT91_MATRIX_ITCM_SIZE (0xf << 0) /* Size of ITCM enabled memory block */ -#define AT91_MATRIX_ITCM_0 (0 << 0) -#define AT91_MATRIX_ITCM_32 (6 << 0) -#define AT91_MATRIX_DTCM_SIZE (0xf << 4) /* Size of DTCM enabled memory block */ -#define AT91_MATRIX_DTCM_0 (0 << 4) -#define AT91_MATRIX_DTCM_32 (6 << 4) -#define AT91_MATRIX_DTCM_64 (7 << 4) -#define AT91_MATRIX_TCM_NWS (0x1 << 11) /* Wait state TCM register */ -#define AT91_MATRIX_TCM_NO_WS (0x0 << 11) -#define AT91_MATRIX_TCM_ONE_WS (0x1 << 11) - -#define AT91_MATRIX_VIDEO 0x118 /* Video Mode Configuration Register */ -#define AT91C_VDEC_SEL (0x1 << 0) /* Video Mode Selection */ -#define AT91C_VDEC_SEL_OFF (0 << 0) -#define AT91C_VDEC_SEL_ON (1 << 0) - -#define AT91_MATRIX_EBICSA 0x128 /* EBI Chip Select Assignment Register */ -#define AT91_MATRIX_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */ -#define AT91_MATRIX_EBI_CS1A_SMC (0 << 1) -#define AT91_MATRIX_EBI_CS1A_SDRAMC (1 << 1) -#define AT91_MATRIX_EBI_CS3A (1 << 3) /* Chip Select 3 Assignment */ -#define AT91_MATRIX_EBI_CS3A_SMC (0 << 3) -#define AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA (1 << 3) -#define AT91_MATRIX_EBI_CS4A (1 << 4) /* Chip Select 4 Assignment */ -#define AT91_MATRIX_EBI_CS4A_SMC (0 << 4) -#define AT91_MATRIX_EBI_CS4A_SMC_CF0 (1 << 4) -#define AT91_MATRIX_EBI_CS5A (1 << 5) /* Chip Select 5 Assignment */ -#define AT91_MATRIX_EBI_CS5A_SMC (0 << 5) -#define AT91_MATRIX_EBI_CS5A_SMC_CF1 (1 << 5) -#define AT91_MATRIX_EBI_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ -#define AT91_MATRIX_EBI_DBPU_ON (0 << 8) -#define AT91_MATRIX_EBI_DBPU_OFF (1 << 8) -#define AT91_MATRIX_EBI_VDDIOMSEL (1 << 16) /* Memory voltage selection */ -#define AT91_MATRIX_EBI_VDDIOMSEL_1_8V (0 << 16) -#define AT91_MATRIX_EBI_VDDIOMSEL_3_3V (1 << 16) -#define AT91_MATRIX_EBI_EBI_IOSR (1 << 17) /* EBI I/O slew rate selection */ -#define AT91_MATRIX_EBI_EBI_IOSR_REDUCED (0 << 17) -#define AT91_MATRIX_EBI_EBI_IOSR_NORMAL (1 << 17) -#define AT91_MATRIX_EBI_DDR_IOSR (1 << 18) /* DDR2 dedicated port I/O slew rate selection */ -#define AT91_MATRIX_EBI_DDR_IOSR_REDUCED (0 << 18) -#define AT91_MATRIX_EBI_DDR_IOSR_NORMAL (1 << 18) - -#define AT91_MATRIX_WPMR 0x1E4 /* Write Protect Mode Register */ -#define AT91_MATRIX_WPMR_WPEN (1 << 0) /* Write Protect ENable */ -#define AT91_MATRIX_WPMR_WP_WPDIS (0 << 0) -#define AT91_MATRIX_WPMR_WP_WPEN (1 << 0) -#define AT91_MATRIX_WPMR_WPKEY (0xFFFFFF << 8) /* Write Protect KEY */ - -#define AT91_MATRIX_WPSR 0x1E8 /* Write Protect Status Register */ -#define AT91_MATRIX_WPSR_WPVS (1 << 0) /* Write Protect Violation Status */ -#define AT91_MATRIX_WPSR_NO_WPV (0 << 0) -#define AT91_MATRIX_WPSR_WPV (1 << 0) -#define AT91_MATRIX_WPSR_WPVSRC (0xFFFF << 8) /* Write Protect Violation Source */ - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9n12.h b/arch/arm/mach-at91/include/mach/at91sam9n12.h deleted file mode 100644 index 0151bcf6163c..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9n12.h +++ /dev/null @@ -1,65 +0,0 @@ -/* - * SoC specific header file for the AT91SAM9N12 - * - * Copyright (C) 2012 Atmel Corporation - * - * Common definitions, based on AT91SAM9N12 SoC datasheet - * - * Licensed under GPLv2 or later - */ - -#ifndef _AT91SAM9N12_H_ -#define _AT91SAM9N12_H_ - -/* - * Peripheral identifiers/interrupts. - */ -#define AT91SAM9N12_ID_PIOAB 2 /* Parallel I/O Controller A and B */ -#define AT91SAM9N12_ID_PIOCD 3 /* Parallel I/O Controller C and D */ -#define AT91SAM9N12_ID_FUSE 4 /* FUSE Controller */ -#define AT91SAM9N12_ID_USART0 5 /* USART 0 */ -#define AT91SAM9N12_ID_USART1 6 /* USART 1 */ -#define AT91SAM9N12_ID_USART2 7 /* USART 2 */ -#define AT91SAM9N12_ID_USART3 8 /* USART 3 */ -#define AT91SAM9N12_ID_TWI0 9 /* Two-Wire Interface 0 */ -#define AT91SAM9N12_ID_TWI1 10 /* Two-Wire Interface 1 */ -#define AT91SAM9N12_ID_MCI 12 /* High Speed Multimedia Card Interface */ -#define AT91SAM9N12_ID_SPI0 13 /* Serial Peripheral Interface 0 */ -#define AT91SAM9N12_ID_SPI1 14 /* Serial Peripheral Interface 1 */ -#define AT91SAM9N12_ID_UART0 15 /* UART 0 */ -#define AT91SAM9N12_ID_UART1 16 /* UART 1 */ -#define AT91SAM9N12_ID_TCB 17 /* Timer Counter 0, 1, 2, 3, 4 and 5 */ -#define AT91SAM9N12_ID_PWM 18 /* Pulse Width Modulation Controller */ -#define AT91SAM9N12_ID_ADC 19 /* ADC Controller */ -#define AT91SAM9N12_ID_DMA 20 /* DMA Controller */ -#define AT91SAM9N12_ID_UHP 22 /* USB Host High Speed */ -#define AT91SAM9N12_ID_UDP 23 /* USB Device High Speed */ -#define AT91SAM9N12_ID_LCDC 25 /* LCD Controller */ -#define AT91SAM9N12_ID_ISI 25 /* Image Sensor Interface */ -#define AT91SAM9N12_ID_SSC 28 /* Synchronous Serial Controller */ -#define AT91SAM9N12_ID_TRNG 30 /* TRNG */ -#define AT91SAM9N12_ID_IRQ0 31 /* Advanced Interrupt Controller */ - -/* - * User Peripheral physical base addresses. - */ -#define AT91SAM9N12_BASE_USART0 0xf801c000 -#define AT91SAM9N12_BASE_USART1 0xf8020000 -#define AT91SAM9N12_BASE_USART2 0xf8024000 -#define AT91SAM9N12_BASE_USART3 0xf8028000 - -/* - * System Peripherals - */ -#define AT91SAM9N12_BASE_RTC 0xfffffeb0 - -/* - * Internal Memory. - */ -#define AT91SAM9N12_SRAM_BASE 0x00300000 /* Internal SRAM base address */ -#define AT91SAM9N12_SRAM_SIZE SZ_32K /* Internal SRAM size (32Kb) */ - -#define AT91SAM9N12_ROM_BASE 0x00100000 /* Internal ROM base address */ -#define AT91SAM9N12_ROM_SIZE SZ_128K /* Internal ROM size (128Kb) */ - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9n12_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9n12_matrix.h deleted file mode 100644 index 40060cd62fa9..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9n12_matrix.h +++ /dev/null @@ -1,53 +0,0 @@ -/* - * Matrix-centric header file for the AT91SAM9N12 - * - * Copyright (C) 2012 Atmel Corporation. - * - * Only EBI related registers. - * Write Protect register definitions may be useful. - * - * Licensed under GPLv2 or later. - */ - -#ifndef _AT91SAM9N12_MATRIX_H_ -#define _AT91SAM9N12_MATRIX_H_ - -#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x118) /* EBI Chip Select Assignment Register */ -#define AT91_MATRIX_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */ -#define AT91_MATRIX_EBI_CS1A_SMC (0 << 1) -#define AT91_MATRIX_EBI_CS1A_SDRAMC (1 << 1) -#define AT91_MATRIX_EBI_CS3A (1 << 3) /* Chip Select 3 Assignment */ -#define AT91_MATRIX_EBI_CS3A_SMC (0 << 3) -#define AT91_MATRIX_EBI_CS3A_SMC_NANDFLASH (1 << 3) -#define AT91_MATRIX_EBI_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ -#define AT91_MATRIX_EBI_DBPU_ON (0 << 8) -#define AT91_MATRIX_EBI_DBPU_OFF (1 << 8) -#define AT91_MATRIX_EBI_VDDIOMSEL (1 << 16) /* Memory voltage selection */ -#define AT91_MATRIX_EBI_VDDIOMSEL_1_8V (0 << 16) -#define AT91_MATRIX_EBI_VDDIOMSEL_3_3V (1 << 16) -#define AT91_MATRIX_EBI_EBI_IOSR (1 << 17) /* EBI I/O slew rate selection */ -#define AT91_MATRIX_EBI_EBI_IOSR_REDUCED (0 << 17) -#define AT91_MATRIX_EBI_EBI_IOSR_NORMAL (1 << 17) -#define AT91_MATRIX_EBI_DDR_IOSR (1 << 18) /* DDR2 dedicated port I/O slew rate selection */ -#define AT91_MATRIX_EBI_DDR_IOSR_REDUCED (0 << 18) -#define AT91_MATRIX_EBI_DDR_IOSR_NORMAL (1 << 18) -#define AT91_MATRIX_NFD0_SELECT (1 << 24) /* NAND Flash Data Bus Selection */ -#define AT91_MATRIX_NFD0_ON_D0 (0 << 24) -#define AT91_MATRIX_NFD0_ON_D16 (1 << 24) -#define AT91_MATRIX_DDR_MP_EN (1 << 25) /* DDR Multi-port Enable */ -#define AT91_MATRIX_MP_OFF (0 << 25) -#define AT91_MATRIX_MP_ON (1 << 25) - -#define AT91_MATRIX_WPMR (AT91_MATRIX + 0x1E4) /* Write Protect Mode Register */ -#define AT91_MATRIX_WPMR_WPEN (1 << 0) /* Write Protect ENable */ -#define AT91_MATRIX_WPMR_WP_WPDIS (0 << 0) -#define AT91_MATRIX_WPMR_WP_WPEN (1 << 0) -#define AT91_MATRIX_WPMR_WPKEY (0xFFFFFF << 8) /* Write Protect KEY */ - -#define AT91_MATRIX_WPSR (AT91_MATRIX + 0x1E8) /* Write Protect Status Register */ -#define AT91_MATRIX_WPSR_WPVS (1 << 0) /* Write Protect Violation Status */ -#define AT91_MATRIX_WPSR_NO_WPV (0 << 0) -#define AT91_MATRIX_WPSR_WPV (1 << 0) -#define AT91_MATRIX_WPSR_WPVSRC (0xFFFF << 8) /* Write Protect Violation Source */ - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9rl.h b/arch/arm/mach-at91/include/mach/at91sam9rl.h deleted file mode 100644 index a15db56d33fa..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9rl.h +++ /dev/null @@ -1,105 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/at91sam9260.h - * - * Copyright (C) 2007 Atmel Corporation - * - * Common definitions. - * Based on AT91SAM9RL datasheet revision A. (Preliminary) - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file COPYING in the main directory of this archive for - * more details. - */ - -#ifndef AT91SAM9RL_H -#define AT91SAM9RL_H - -/* - * Peripheral identifiers/interrupts. - */ -#define AT91SAM9RL_ID_PIOA 2 /* Parallel IO Controller A */ -#define AT91SAM9RL_ID_PIOB 3 /* Parallel IO Controller B */ -#define AT91SAM9RL_ID_PIOC 4 /* Parallel IO Controller C */ -#define AT91SAM9RL_ID_PIOD 5 /* Parallel IO Controller D */ -#define AT91SAM9RL_ID_US0 6 /* USART 0 */ -#define AT91SAM9RL_ID_US1 7 /* USART 1 */ -#define AT91SAM9RL_ID_US2 8 /* USART 2 */ -#define AT91SAM9RL_ID_US3 9 /* USART 3 */ -#define AT91SAM9RL_ID_MCI 10 /* Multimedia Card Interface */ -#define AT91SAM9RL_ID_TWI0 11 /* TWI 0 */ -#define AT91SAM9RL_ID_TWI1 12 /* TWI 1 */ -#define AT91SAM9RL_ID_SPI 13 /* Serial Peripheral Interface */ -#define AT91SAM9RL_ID_SSC0 14 /* Serial Synchronous Controller 0 */ -#define AT91SAM9RL_ID_SSC1 15 /* Serial Synchronous Controller 1 */ -#define AT91SAM9RL_ID_TC0 16 /* Timer Counter 0 */ -#define AT91SAM9RL_ID_TC1 17 /* Timer Counter 1 */ -#define AT91SAM9RL_ID_TC2 18 /* Timer Counter 2 */ -#define AT91SAM9RL_ID_PWMC 19 /* Pulse Width Modulation Controller */ -#define AT91SAM9RL_ID_TSC 20 /* Touch Screen Controller */ -#define AT91SAM9RL_ID_DMA 21 /* DMA Controller */ -#define AT91SAM9RL_ID_UDPHS 22 /* USB Device HS */ -#define AT91SAM9RL_ID_LCDC 23 /* LCD Controller */ -#define AT91SAM9RL_ID_AC97C 24 /* AC97 Controller */ -#define AT91SAM9RL_ID_IRQ0 31 /* Advanced Interrupt Controller (IRQ0) */ - - -/* - * User Peripheral physical base addresses. - */ -#define AT91SAM9RL_BASE_TCB0 0xfffa0000 -#define AT91SAM9RL_BASE_TC0 0xfffa0000 -#define AT91SAM9RL_BASE_TC1 0xfffa0040 -#define AT91SAM9RL_BASE_TC2 0xfffa0080 -#define AT91SAM9RL_BASE_MCI 0xfffa4000 -#define AT91SAM9RL_BASE_TWI0 0xfffa8000 -#define AT91SAM9RL_BASE_TWI1 0xfffac000 -#define AT91SAM9RL_BASE_US0 0xfffb0000 -#define AT91SAM9RL_BASE_US1 0xfffb4000 -#define AT91SAM9RL_BASE_US2 0xfffb8000 -#define AT91SAM9RL_BASE_US3 0xfffbc000 -#define AT91SAM9RL_BASE_SSC0 0xfffc0000 -#define AT91SAM9RL_BASE_SSC1 0xfffc4000 -#define AT91SAM9RL_BASE_PWMC 0xfffc8000 -#define AT91SAM9RL_BASE_SPI 0xfffcc000 -#define AT91SAM9RL_BASE_TSC 0xfffd0000 -#define AT91SAM9RL_BASE_UDPHS 0xfffd4000 -#define AT91SAM9RL_BASE_AC97C 0xfffd8000 - - -/* - * System Peripherals (offset from AT91_BASE_SYS) - */ -#define AT91_SCKCR (0xfffffd50 - AT91_BASE_SYS) - -#define AT91SAM9RL_BASE_DMA 0xffffe600 -#define AT91SAM9RL_BASE_ECC 0xffffe800 -#define AT91SAM9RL_BASE_SDRAMC 0xffffea00 -#define AT91SAM9RL_BASE_SMC 0xffffec00 -#define AT91SAM9RL_BASE_MATRIX 0xffffee00 -#define AT91SAM9RL_BASE_DBGU AT91_BASE_DBGU0 -#define AT91SAM9RL_BASE_PIOA 0xfffff400 -#define AT91SAM9RL_BASE_PIOB 0xfffff600 -#define AT91SAM9RL_BASE_PIOC 0xfffff800 -#define AT91SAM9RL_BASE_PIOD 0xfffffa00 -#define AT91SAM9RL_BASE_RSTC 0xfffffd00 -#define AT91SAM9RL_BASE_SHDWC 0xfffffd10 -#define AT91SAM9RL_BASE_RTT 0xfffffd20 -#define AT91SAM9RL_BASE_PIT 0xfffffd30 -#define AT91SAM9RL_BASE_WDT 0xfffffd40 -#define AT91SAM9RL_BASE_GPBR 0xfffffd60 -#define AT91SAM9RL_BASE_RTC 0xfffffe00 - - -/* - * Internal Memory. - */ -#define AT91SAM9RL_SRAM_BASE 0x00300000 /* Internal SRAM base address */ -#define AT91SAM9RL_SRAM_SIZE SZ_16K /* Internal SRAM size (16Kb) */ - -#define AT91SAM9RL_ROM_BASE 0x00400000 /* Internal ROM base address */ -#define AT91SAM9RL_ROM_SIZE (2 * SZ_16K) /* Internal ROM size (32Kb) */ - -#define AT91SAM9RL_LCDC_BASE 0x00500000 /* LCD Controller */ -#define AT91SAM9RL_UDPHS_FIFO 0x00600000 /* USB Device HS controller */ - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9rl_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9rl_matrix.h deleted file mode 100644 index 6d160adadafc..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9rl_matrix.h +++ /dev/null @@ -1,96 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/at91sam9rl_matrix.h - * - * Copyright (C) 2007 Atmel Corporation - * - * Memory Controllers (MATRIX, EBI) - System peripherals registers. - * Based on AT91SAM9RL datasheet revision A. (Preliminary) - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file COPYING in the main directory of this archive for - * more details. - */ - -#ifndef AT91SAM9RL_MATRIX_H -#define AT91SAM9RL_MATRIX_H - -#define AT91_MATRIX_MCFG0 0x00 /* Master Configuration Register 0 */ -#define AT91_MATRIX_MCFG1 0x04 /* Master Configuration Register 1 */ -#define AT91_MATRIX_MCFG2 0x08 /* Master Configuration Register 2 */ -#define AT91_MATRIX_MCFG3 0x0C /* Master Configuration Register 3 */ -#define AT91_MATRIX_MCFG4 0x10 /* Master Configuration Register 4 */ -#define AT91_MATRIX_MCFG5 0x14 /* Master Configuration Register 5 */ -#define AT91_MATRIX_ULBT (7 << 0) /* Undefined Length Burst Type */ -#define AT91_MATRIX_ULBT_INFINITE (0 << 0) -#define AT91_MATRIX_ULBT_SINGLE (1 << 0) -#define AT91_MATRIX_ULBT_FOUR (2 << 0) -#define AT91_MATRIX_ULBT_EIGHT (3 << 0) -#define AT91_MATRIX_ULBT_SIXTEEN (4 << 0) - -#define AT91_MATRIX_SCFG0 0x40 /* Slave Configuration Register 0 */ -#define AT91_MATRIX_SCFG1 0x44 /* Slave Configuration Register 1 */ -#define AT91_MATRIX_SCFG2 0x48 /* Slave Configuration Register 2 */ -#define AT91_MATRIX_SCFG3 0x4C /* Slave Configuration Register 3 */ -#define AT91_MATRIX_SCFG4 0x50 /* Slave Configuration Register 4 */ -#define AT91_MATRIX_SCFG5 0x54 /* Slave Configuration Register 5 */ -#define AT91_MATRIX_SLOT_CYCLE (0xff << 0) /* Maximum Number of Allowed Cycles for a Burst */ -#define AT91_MATRIX_DEFMSTR_TYPE (3 << 16) /* Default Master Type */ -#define AT91_MATRIX_DEFMSTR_TYPE_NONE (0 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_LAST (1 << 16) -#define AT91_MATRIX_DEFMSTR_TYPE_FIXED (2 << 16) -#define AT91_MATRIX_FIXED_DEFMSTR (0xf << 18) /* Fixed Index of Default Master */ -#define AT91_MATRIX_ARBT (3 << 24) /* Arbitration Type */ -#define AT91_MATRIX_ARBT_ROUND_ROBIN (0 << 24) -#define AT91_MATRIX_ARBT_FIXED_PRIORITY (1 << 24) - -#define AT91_MATRIX_PRAS0 0x80 /* Priority Register A for Slave 0 */ -#define AT91_MATRIX_PRAS1 0x88 /* Priority Register A for Slave 1 */ -#define AT91_MATRIX_PRAS2 0x90 /* Priority Register A for Slave 2 */ -#define AT91_MATRIX_PRAS3 0x98 /* Priority Register A for Slave 3 */ -#define AT91_MATRIX_PRAS4 0xA0 /* Priority Register A for Slave 4 */ -#define AT91_MATRIX_PRAS5 0xA8 /* Priority Register A for Slave 5 */ -#define AT91_MATRIX_M0PR (3 << 0) /* Master 0 Priority */ -#define AT91_MATRIX_M1PR (3 << 4) /* Master 1 Priority */ -#define AT91_MATRIX_M2PR (3 << 8) /* Master 2 Priority */ -#define AT91_MATRIX_M3PR (3 << 12) /* Master 3 Priority */ -#define AT91_MATRIX_M4PR (3 << 16) /* Master 4 Priority */ -#define AT91_MATRIX_M5PR (3 << 20) /* Master 5 Priority */ - -#define AT91_MATRIX_MRCR 0x100 /* Master Remap Control Register */ -#define AT91_MATRIX_RCB0 (1 << 0) /* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */ -#define AT91_MATRIX_RCB1 (1 << 1) /* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */ -#define AT91_MATRIX_RCB2 (1 << 2) -#define AT91_MATRIX_RCB3 (1 << 3) -#define AT91_MATRIX_RCB4 (1 << 4) -#define AT91_MATRIX_RCB5 (1 << 5) - -#define AT91_MATRIX_TCMR 0x114 /* TCM Configuration Register */ -#define AT91_MATRIX_ITCM_SIZE (0xf << 0) /* Size of ITCM enabled memory block */ -#define AT91_MATRIX_ITCM_0 (0 << 0) -#define AT91_MATRIX_ITCM_16 (5 << 0) -#define AT91_MATRIX_ITCM_32 (6 << 0) -#define AT91_MATRIX_DTCM_SIZE (0xf << 4) /* Size of DTCM enabled memory block */ -#define AT91_MATRIX_DTCM_0 (0 << 4) -#define AT91_MATRIX_DTCM_16 (5 << 4) -#define AT91_MATRIX_DTCM_32 (6 << 4) - -#define AT91_MATRIX_EBICSA 0x120 /* EBI0 Chip Select Assignment Register */ -#define AT91_MATRIX_CS1A (1 << 1) /* Chip Select 1 Assignment */ -#define AT91_MATRIX_CS1A_SMC (0 << 1) -#define AT91_MATRIX_CS1A_SDRAMC (1 << 1) -#define AT91_MATRIX_CS3A (1 << 3) /* Chip Select 3 Assignment */ -#define AT91_MATRIX_CS3A_SMC (0 << 3) -#define AT91_MATRIX_CS3A_SMC_SMARTMEDIA (1 << 3) -#define AT91_MATRIX_CS4A (1 << 4) /* Chip Select 4 Assignment */ -#define AT91_MATRIX_CS4A_SMC (0 << 4) -#define AT91_MATRIX_CS4A_SMC_CF1 (1 << 4) -#define AT91_MATRIX_CS5A (1 << 5) /* Chip Select 5 Assignment */ -#define AT91_MATRIX_CS5A_SMC (0 << 5) -#define AT91_MATRIX_CS5A_SMC_CF2 (1 << 5) -#define AT91_MATRIX_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ -#define AT91_MATRIX_VDDIOMSEL (1 << 16) /* Memory voltage selection */ -#define AT91_MATRIX_VDDIOMSEL_1_8V (0 << 16) -#define AT91_MATRIX_VDDIOMSEL_3_3V (1 << 16) - - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9x5.h b/arch/arm/mach-at91/include/mach/at91sam9x5.h deleted file mode 100644 index 2fc76c49e97c..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9x5.h +++ /dev/null @@ -1,71 +0,0 @@ -/* - * Chip-specific header file for the AT91SAM9x5 family - * - * Copyright (C) 2009-2012 Atmel Corporation. - * - * Common definitions. - * Based on AT91SAM9x5 datasheet. - * - * Licensed under GPLv2 or later. - */ - -#ifndef AT91SAM9X5_H -#define AT91SAM9X5_H - -/* - * Peripheral identifiers/interrupts. - */ -#define AT91SAM9X5_ID_PIOAB 2 /* Parallel I/O Controller A and B */ -#define AT91SAM9X5_ID_PIOCD 3 /* Parallel I/O Controller C and D */ -#define AT91SAM9X5_ID_SMD 4 /* SMD Soft Modem (SMD) */ -#define AT91SAM9X5_ID_USART0 5 /* USART 0 */ -#define AT91SAM9X5_ID_USART1 6 /* USART 1 */ -#define AT91SAM9X5_ID_USART2 7 /* USART 2 */ -#define AT91SAM9X5_ID_USART3 8 /* USART 3 */ -#define AT91SAM9X5_ID_TWI0 9 /* Two-Wire Interface 0 */ -#define AT91SAM9X5_ID_TWI1 10 /* Two-Wire Interface 1 */ -#define AT91SAM9X5_ID_TWI2 11 /* Two-Wire Interface 2 */ -#define AT91SAM9X5_ID_MCI0 12 /* High Speed Multimedia Card Interface 0 */ -#define AT91SAM9X5_ID_SPI0 13 /* Serial Peripheral Interface 0 */ -#define AT91SAM9X5_ID_SPI1 14 /* Serial Peripheral Interface 1 */ -#define AT91SAM9X5_ID_UART0 15 /* UART 0 */ -#define AT91SAM9X5_ID_UART1 16 /* UART 1 */ -#define AT91SAM9X5_ID_TCB 17 /* Timer Counter 0, 1, 2, 3, 4 and 5 */ -#define AT91SAM9X5_ID_PWM 18 /* Pulse Width Modulation Controller */ -#define AT91SAM9X5_ID_ADC 19 /* ADC Controller */ -#define AT91SAM9X5_ID_DMA0 20 /* DMA Controller 0 */ -#define AT91SAM9X5_ID_DMA1 21 /* DMA Controller 1 */ -#define AT91SAM9X5_ID_UHPHS 22 /* USB Host High Speed */ -#define AT91SAM9X5_ID_UDPHS 23 /* USB Device High Speed */ -#define AT91SAM9X5_ID_EMAC0 24 /* Ethernet MAC0 */ -#define AT91SAM9X5_ID_LCDC 25 /* LCD Controller */ -#define AT91SAM9X5_ID_ISI 25 /* Image Sensor Interface */ -#define AT91SAM9X5_ID_MCI1 26 /* High Speed Multimedia Card Interface 1 */ -#define AT91SAM9X5_ID_EMAC1 27 /* Ethernet MAC1 */ -#define AT91SAM9X5_ID_SSC 28 /* Synchronous Serial Controller */ -#define AT91SAM9X5_ID_CAN0 29 /* CAN Controller 0 */ -#define AT91SAM9X5_ID_CAN1 30 /* CAN Controller 1 */ -#define AT91SAM9X5_ID_IRQ0 31 /* Advanced Interrupt Controller */ - -/* - * User Peripheral physical base addresses. - */ -#define AT91SAM9X5_BASE_USART0 0xf801c000 -#define AT91SAM9X5_BASE_USART1 0xf8020000 -#define AT91SAM9X5_BASE_USART2 0xf8024000 - -/* - * System Peripherals - */ -#define AT91SAM9X5_BASE_RTC 0xfffffeb0 - -/* - * Internal Memory. - */ -#define AT91SAM9X5_SRAM_BASE 0x00300000 /* Internal SRAM base address */ -#define AT91SAM9X5_SRAM_SIZE SZ_32K /* Internal SRAM size (32Kb) */ - -#define AT91SAM9X5_ROM_BASE 0x00400000 /* Internal ROM base address */ -#define AT91SAM9X5_ROM_SIZE SZ_64K /* Internal ROM size (64Kb) */ - -#endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9x5_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9x5_matrix.h deleted file mode 100644 index a606d3966470..000000000000 --- a/arch/arm/mach-at91/include/mach/at91sam9x5_matrix.h +++ /dev/null @@ -1,53 +0,0 @@ -/* - * Matrix-centric header file for the AT91SAM9x5 family - * - * Copyright (C) 2009-2012 Atmel Corporation. - * - * Only EBI related registers. - * Write Protect register definitions may be useful. - * - * Licensed under GPLv2 or later. - */ - -#ifndef AT91SAM9X5_MATRIX_H -#define AT91SAM9X5_MATRIX_H - -#define AT91_MATRIX_EBICSA (AT91_MATRIX + 0x120) /* EBI Chip Select Assignment Register */ -#define AT91_MATRIX_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */ -#define AT91_MATRIX_EBI_CS1A_SMC (0 << 1) -#define AT91_MATRIX_EBI_CS1A_SDRAMC (1 << 1) -#define AT91_MATRIX_EBI_CS3A (1 << 3) /* Chip Select 3 Assignment */ -#define AT91_MATRIX_EBI_CS3A_SMC (0 << 3) -#define AT91_MATRIX_EBI_CS3A_SMC_NANDFLASH (1 << 3) -#define AT91_MATRIX_EBI_DBPUC (1 << 8) /* Data Bus Pull-up Configuration */ -#define AT91_MATRIX_EBI_DBPU_ON (0 << 8) -#define AT91_MATRIX_EBI_DBPU_OFF (1 << 8) -#define AT91_MATRIX_EBI_VDDIOMSEL (1 << 16) /* Memory voltage selection */ -#define AT91_MATRIX_EBI_VDDIOMSEL_1_8V (0 << 16) -#define AT91_MATRIX_EBI_VDDIOMSEL_3_3V (1 << 16) -#define AT91_MATRIX_EBI_EBI_IOSR (1 << 17) /* EBI I/O slew rate selection */ -#define AT91_MATRIX_EBI_EBI_IOSR_REDUCED (0 << 17) -#define AT91_MATRIX_EBI_EBI_IOSR_NORMAL (1 << 17) -#define AT91_MATRIX_EBI_DDR_IOSR (1 << 18) /* DDR2 dedicated port I/O slew rate selection */ -#define AT91_MATRIX_EBI_DDR_IOSR_REDUCED (0 << 18) -#define AT91_MATRIX_EBI_DDR_IOSR_NORMAL (1 << 18) -#define AT91_MATRIX_NFD0_SELECT (1 << 24) /* NAND Flash Data Bus Selection */ -#define AT91_MATRIX_NFD0_ON_D0 (0 << 24) -#define AT91_MATRIX_NFD0_ON_D16 (1 << 24) -#define AT91_MATRIX_DDR_MP_EN (1 << 25) /* DDR Multi-port Enable */ -#define AT91_MATRIX_MP_OFF (0 << 25) -#define AT91_MATRIX_MP_ON (1 << 25) - -#define AT91_MATRIX_WPMR (AT91_MATRIX + 0x1E4) /* Write Protect Mode Register */ -#define AT91_MATRIX_WPMR_WPEN (1 << 0) /* Write Protect ENable */ -#define AT91_MATRIX_WPMR_WP_WPDIS (0 << 0) -#define AT91_MATRIX_WPMR_WP_WPEN (1 << 0) -#define AT91_MATRIX_WPMR_WPKEY (0xFFFFFF << 8) /* Write Protect KEY */ - -#define AT91_MATRIX_WPSR (AT91_MATRIX + 0x1E8) /* Write Protect Status Register */ -#define AT91_MATRIX_WPSR_WPVS (1 << 0) /* Write Protect Violation Status */ -#define AT91_MATRIX_WPSR_NO_WPV (0 << 0) -#define AT91_MATRIX_WPSR_WPV (1 << 0) -#define AT91_MATRIX_WPSR_WPVSRC (0xFFFF << 8) /* Write Protect Violation Source */ - -#endif diff --git a/arch/arm/mach-at91/include/mach/cpu.h b/arch/arm/mach-at91/include/mach/cpu.h deleted file mode 100644 index ce7c80a44983..000000000000 --- a/arch/arm/mach-at91/include/mach/cpu.h +++ /dev/null @@ -1,216 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/cpu.h - * - * Copyright (C) 2006 SAN People - * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ - -#ifndef __MACH_CPU_H__ -#define __MACH_CPU_H__ - -#define ARCH_ID_AT91RM9200 0x09290780 -#define ARCH_ID_AT91SAM9260 0x019803a0 -#define ARCH_ID_AT91SAM9261 0x019703a0 -#define ARCH_ID_AT91SAM9263 0x019607a0 -#define ARCH_ID_AT91SAM9G10 0x019903a0 -#define ARCH_ID_AT91SAM9G20 0x019905a0 -#define ARCH_ID_AT91SAM9RL64 0x019b03a0 -#define ARCH_ID_AT91SAM9G45 0x819b05a0 -#define ARCH_ID_AT91SAM9G45MRL 0x819b05a2 /* aka 9G45-ES2 & non ES lots */ -#define ARCH_ID_AT91SAM9G45ES 0x819b05a1 /* 9G45-ES (Engineering Sample) */ -#define ARCH_ID_AT91SAM9X5 0x819a05a0 -#define ARCH_ID_AT91SAM9N12 0x819a07a0 - -#define ARCH_ID_AT91SAM9XE128 0x329973a0 -#define ARCH_ID_AT91SAM9XE256 0x329a93a0 -#define ARCH_ID_AT91SAM9XE512 0x329aa3a0 - -#define ARCH_ID_AT91M40800 0x14080044 -#define ARCH_ID_AT91R40807 0x44080746 -#define ARCH_ID_AT91M40807 0x14080745 -#define ARCH_ID_AT91R40008 0x44000840 - -#define ARCH_ID_SAMA5 0x8A5C07C0 - -#define ARCH_EXID_AT91SAM9M11 0x00000001 -#define ARCH_EXID_AT91SAM9M10 0x00000002 -#define ARCH_EXID_AT91SAM9G46 0x00000003 -#define ARCH_EXID_AT91SAM9G45 0x00000004 - -#define ARCH_EXID_AT91SAM9G15 0x00000000 -#define ARCH_EXID_AT91SAM9G35 0x00000001 -#define ARCH_EXID_AT91SAM9X35 0x00000002 -#define ARCH_EXID_AT91SAM9G25 0x00000003 -#define ARCH_EXID_AT91SAM9X25 0x00000004 - -#define ARCH_EXID_SAMA5D3 0x00004300 -#define ARCH_EXID_SAMA5D31 0x00444300 -#define ARCH_EXID_SAMA5D33 0x00414300 -#define ARCH_EXID_SAMA5D34 0x00414301 -#define ARCH_EXID_SAMA5D35 0x00584300 -#define ARCH_EXID_SAMA5D36 0x00004301 - -#define ARCH_EXID_SAMA5D4 0x00000007 -#define ARCH_EXID_SAMA5D41 0x00000001 -#define ARCH_EXID_SAMA5D42 0x00000002 -#define ARCH_EXID_SAMA5D43 0x00000003 -#define ARCH_EXID_SAMA5D44 0x00000004 - -#define ARCH_FAMILY_AT91SAM9 0x01900000 -#define ARCH_FAMILY_AT91SAM9XE 0x02900000 - -/* RM9200 type */ -#define ARCH_REVISON_9200_BGA (0 << 0) -#define ARCH_REVISON_9200_PQFP (1 << 0) - -#ifndef __ASSEMBLY__ -enum at91_soc_type { - /* 920T */ - AT91_SOC_RM9200, - - /* SAM92xx */ - AT91_SOC_SAM9260, AT91_SOC_SAM9261, AT91_SOC_SAM9263, - - /* SAM9Gxx */ - AT91_SOC_SAM9G10, AT91_SOC_SAM9G20, AT91_SOC_SAM9G45, - - /* SAM9RL */ - AT91_SOC_SAM9RL, - - /* SAM9X5 */ - AT91_SOC_SAM9X5, - - /* SAM9N12 */ - AT91_SOC_SAM9N12, - - /* SAMA5D3 */ - AT91_SOC_SAMA5D3, - - /* SAMA5D4 */ - AT91_SOC_SAMA5D4, - - /* Unknown type */ - AT91_SOC_UNKNOWN, -}; - -enum at91_soc_subtype { - /* RM9200 */ - AT91_SOC_RM9200_BGA, AT91_SOC_RM9200_PQFP, - - /* SAM9260 */ - AT91_SOC_SAM9XE, - - /* SAM9G45 */ - AT91_SOC_SAM9G45ES, AT91_SOC_SAM9M10, AT91_SOC_SAM9G46, AT91_SOC_SAM9M11, - - /* SAM9X5 */ - AT91_SOC_SAM9G15, AT91_SOC_SAM9G35, AT91_SOC_SAM9X35, - AT91_SOC_SAM9G25, AT91_SOC_SAM9X25, - - /* SAMA5D3 */ - AT91_SOC_SAMA5D31, AT91_SOC_SAMA5D33, AT91_SOC_SAMA5D34, - AT91_SOC_SAMA5D35, AT91_SOC_SAMA5D36, - - /* SAMA5D4 */ - AT91_SOC_SAMA5D41, AT91_SOC_SAMA5D42, AT91_SOC_SAMA5D43, - AT91_SOC_SAMA5D44, - - /* No subtype for this SoC */ - AT91_SOC_SUBTYPE_NONE, - - /* Unknown subtype */ - AT91_SOC_SUBTYPE_UNKNOWN, -}; - -struct at91_socinfo { - unsigned int type, subtype; - unsigned int cidr, exid; -}; - -extern struct at91_socinfo at91_soc_initdata; -const char *at91_get_soc_type(struct at91_socinfo *c); -const char *at91_get_soc_subtype(struct at91_socinfo *c); - -static inline int at91_soc_is_detected(void) -{ - return at91_soc_initdata.type != AT91_SOC_UNKNOWN; -} - -#ifdef CONFIG_SOC_AT91RM9200 -#define cpu_is_at91rm9200() (at91_soc_initdata.type == AT91_SOC_RM9200) -#define cpu_is_at91rm9200_bga() (at91_soc_initdata.subtype == AT91_SOC_RM9200_BGA) -#define cpu_is_at91rm9200_pqfp() (at91_soc_initdata.subtype == AT91_SOC_RM9200_PQFP) -#else -#define cpu_is_at91rm9200() (0) -#define cpu_is_at91rm9200_bga() (0) -#define cpu_is_at91rm9200_pqfp() (0) -#endif - -#ifdef CONFIG_SOC_AT91SAM9 -#define cpu_is_at91sam9xe() (at91_soc_initdata.subtype == AT91_SOC_SAM9XE) -#define cpu_is_at91sam9260() (at91_soc_initdata.type == AT91_SOC_SAM9260) -#define cpu_is_at91sam9g20() (at91_soc_initdata.type == AT91_SOC_SAM9G20) -#define cpu_is_at91sam9261() (at91_soc_initdata.type == AT91_SOC_SAM9261) -#define cpu_is_at91sam9g10() (at91_soc_initdata.type == AT91_SOC_SAM9G10) -#define cpu_is_at91sam9263() (at91_soc_initdata.type == AT91_SOC_SAM9263) -#define cpu_is_at91sam9rl() (at91_soc_initdata.type == AT91_SOC_SAM9RL) -#define cpu_is_at91sam9g45() (at91_soc_initdata.type == AT91_SOC_SAM9G45) -#define cpu_is_at91sam9g45es() (at91_soc_initdata.subtype == AT91_SOC_SAM9G45ES) -#define cpu_is_at91sam9m10() (at91_soc_initdata.subtype == AT91_SOC_SAM9M10) -#define cpu_is_at91sam9g46() (at91_soc_initdata.subtype == AT91_SOC_SAM9G46) -#define cpu_is_at91sam9m11() (at91_soc_initdata.subtype == AT91_SOC_SAM9M11) -#define cpu_is_at91sam9x5() (at91_soc_initdata.type == AT91_SOC_SAM9X5) -#define cpu_is_at91sam9g15() (at91_soc_initdata.subtype == AT91_SOC_SAM9G15) -#define cpu_is_at91sam9g35() (at91_soc_initdata.subtype == AT91_SOC_SAM9G35) -#define cpu_is_at91sam9x35() (at91_soc_initdata.subtype == AT91_SOC_SAM9X35) -#define cpu_is_at91sam9g25() (at91_soc_initdata.subtype == AT91_SOC_SAM9G25) -#define cpu_is_at91sam9x25() (at91_soc_initdata.subtype == AT91_SOC_SAM9X25) -#define cpu_is_at91sam9n12() (at91_soc_initdata.type == AT91_SOC_SAM9N12) -#else -#define cpu_is_at91sam9xe() (0) -#define cpu_is_at91sam9260() (0) -#define cpu_is_at91sam9g20() (0) -#define cpu_is_at91sam9261() (0) -#define cpu_is_at91sam9g10() (0) -#define cpu_is_at91sam9263() (0) -#define cpu_is_at91sam9rl() (0) -#define cpu_is_at91sam9g45() (0) -#define cpu_is_at91sam9g45es() (0) -#define cpu_is_at91sam9m10() (0) -#define cpu_is_at91sam9g46() (0) -#define cpu_is_at91sam9m11() (0) -#define cpu_is_at91sam9x5() (0) -#define cpu_is_at91sam9g15() (0) -#define cpu_is_at91sam9g35() (0) -#define cpu_is_at91sam9x35() (0) -#define cpu_is_at91sam9g25() (0) -#define cpu_is_at91sam9x25() (0) -#define cpu_is_at91sam9n12() (0) -#endif - -#ifdef CONFIG_SOC_SAMA5D3 -#define cpu_is_sama5d3() (at91_soc_initdata.type == AT91_SOC_SAMA5D3) -#else -#define cpu_is_sama5d3() (0) -#endif - -#ifdef CONFIG_SOC_SAMA5D4 -#define cpu_is_sama5d4() (at91_soc_initdata.type == AT91_SOC_SAMA5D4) -#else -#define cpu_is_sama5d4() (0) -#endif - -/* - * Since this is ARM, we will never run on any AVR32 CPU. But these - * definitions may reduce clutter in common drivers. - */ -#define cpu_is_at32ap7000() (0) -#endif /* __ASSEMBLY__ */ - -#endif /* __MACH_CPU_H__ */ diff --git a/arch/arm/mach-at91/include/mach/hardware.h b/arch/arm/mach-at91/include/mach/hardware.h deleted file mode 100644 index cacbaa52418f..000000000000 --- a/arch/arm/mach-at91/include/mach/hardware.h +++ /dev/null @@ -1,134 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/hardware.h - * - * Copyright (C) 2003 SAN People - * Copyright (C) 2003 ATMEL - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - */ - -#ifndef __ASM_ARCH_HARDWARE_H -#define __ASM_ARCH_HARDWARE_H - -#include - -/* DBGU base */ -/* rm9200, 9260/9g20, 9261/9g10, 9rl */ -#define AT91_BASE_DBGU0 0xfffff200 -/* 9263, 9g45, sama5d3 */ -#define AT91_BASE_DBGU1 0xffffee00 -/* sama5d4 */ -#define AT91_BASE_DBGU2 0xfc069000 - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -/* - * On all at91 except rm9200 and x40 have the System Controller starts - * at address 0xffffc000 and has a size of 16KiB. - * - * On rm9200 it's start at 0xfffe4000 of 111KiB with non reserved data starting - * at 0xfffff000 - * - * Removes the individual definitions of AT91_BASE_SYS and - * replaces them with a common version at base 0xfffffc000 and size 16KiB - * and map the same memory space - */ -#define AT91_BASE_SYS 0xffffc000 - -/* - * On sama5d4 there is no system controller, we map some needed peripherals - */ -#define AT91_ALT_BASE_SYS 0xfc069000 - -/* - * On all at91 have the Advanced Interrupt Controller starts at address - * 0xfffff000 and the Power Management Controller starts at 0xfffffc00 - */ -#define AT91_AIC 0xfffff000 -#define AT91_PMC 0xfffffc00 - -/* - * Peripheral identifiers/interrupts. - */ -#define AT91_ID_FIQ 0 /* Advanced Interrupt Controller (FIQ) */ -#define AT91_ID_SYS 1 /* System Peripherals */ - -#ifdef CONFIG_MMU -/* - * Remap the peripherals from address 0xFFF78000 .. 0xFFFFFFFF - * to 0xFEF78000 .. 0xFF000000. (544Kb) - */ -#define AT91_IO_PHYS_BASE 0xFFF78000 -#define AT91_IO_VIRT_BASE IOMEM(0xFF000000 - AT91_IO_SIZE) - -/* - * On sama5d4, remap the peripherals from address 0xFC069000 .. 0xFC06F000 - * to 0xFB069000 .. 0xFB06F000. (24Kb) - */ -#define AT91_ALT_IO_PHYS_BASE AT91_ALT_BASE_SYS -#define AT91_ALT_IO_VIRT_BASE IOMEM(0xFB069000) -#else -/* - * Identity mapping for the non MMU case. - */ -#define AT91_IO_PHYS_BASE AT91_BASE_SYS -#define AT91_IO_VIRT_BASE IOMEM(AT91_IO_PHYS_BASE) - -#define AT91_ALT_IO_PHYS_BASE AT91_ALT_BASE_SYS -#define AT91_ALT_IO_VIRT_BASE IOMEM(AT91_ALT_BASE_SYS) -#endif - -#define AT91_IO_SIZE (0xFFFFFFFF - AT91_IO_PHYS_BASE + 1) - - /* Convert a physical IO address to virtual IO address */ -#define AT91_IO_P2V(x) ((x) - AT91_IO_PHYS_BASE + AT91_IO_VIRT_BASE) -#define AT91_ALT_IO_P2V(x) ((x) - AT91_ALT_IO_PHYS_BASE + AT91_ALT_IO_VIRT_BASE) - -/* - * Virtual to Physical Address mapping for IO devices. - */ -#define AT91_VA_BASE_SYS AT91_IO_P2V(AT91_BASE_SYS) -#define AT91_ALT_VA_BASE_SYS AT91_ALT_IO_P2V(AT91_ALT_BASE_SYS) - - /* Internal SRAM is mapped below the IO devices */ -#define AT91_SRAM_MAX SZ_1M -#define AT91_VIRT_BASE (AT91_IO_VIRT_BASE - AT91_SRAM_MAX) - -/* External Memory Map */ -#define AT91_CHIPSELECT_0 0x10000000 -#define AT91_CHIPSELECT_1 0x20000000 -#define AT91_CHIPSELECT_2 0x30000000 -#define AT91_CHIPSELECT_3 0x40000000 -#define AT91_CHIPSELECT_4 0x50000000 -#define AT91_CHIPSELECT_5 0x60000000 -#define AT91_CHIPSELECT_6 0x70000000 -#define AT91_CHIPSELECT_7 0x80000000 - -/* Clocks */ -#define AT91_SLOW_CLOCK 32768 /* slow clock */ - -/* - * FIXME: this is needed to communicate between the pinctrl driver and - * the PM implementation in the machine. Possibly part of the PM - * implementation should be moved down into the pinctrl driver and get - * called as part of the generic suspend/resume path. - */ -#ifndef __ASSEMBLY__ -extern void at91_pinctrl_gpio_suspend(void); -extern void at91_pinctrl_gpio_resume(void); -#endif - -#endif diff --git a/arch/arm/mach-at91/include/mach/sama5d3.h b/arch/arm/mach-at91/include/mach/sama5d3.h deleted file mode 100644 index 25613d8c6dcd..000000000000 --- a/arch/arm/mach-at91/include/mach/sama5d3.h +++ /dev/null @@ -1,86 +0,0 @@ -/* - * Chip-specific header file for the SAMA5D3 family - * - * Copyright (C) 2013 Atmel, - * 2013 Ludovic Desroches - * - * Common definitions. - * Based on SAMA5D3 datasheet. - * - * Licensed under GPLv2 or later. - */ - -#ifndef SAMA5D3_H -#define SAMA5D3_H - -/* - * Peripheral identifiers/interrupts. - */ -#define AT91_ID_FIQ 0 /* Advanced Interrupt Controller (FIQ) */ -#define AT91_ID_SYS 1 /* System Peripherals */ -#define SAMA5D3_ID_DBGU 2 /* debug Unit (usually no special interrupt line) */ -#define AT91_ID_PIT 3 /* PIT */ -#define SAMA5D3_ID_WDT 4 /* Watchdog Timer Interrupt */ -#define SAMA5D3_ID_HSMC 5 /* Static Memory Controller */ -#define SAMA5D3_ID_PIOA 6 /* PIOA */ -#define SAMA5D3_ID_PIOB 7 /* PIOB */ -#define SAMA5D3_ID_PIOC 8 /* PIOC */ -#define SAMA5D3_ID_PIOD 9 /* PIOD */ -#define SAMA5D3_ID_PIOE 10 /* PIOE */ -#define SAMA5D3_ID_SMD 11 /* SMD Soft Modem */ -#define SAMA5D3_ID_USART0 12 /* USART0 */ -#define SAMA5D3_ID_USART1 13 /* USART1 */ -#define SAMA5D3_ID_USART2 14 /* USART2 */ -#define SAMA5D3_ID_USART3 15 /* USART3 */ -#define SAMA5D3_ID_UART0 16 /* UART 0 */ -#define SAMA5D3_ID_UART1 17 /* UART 1 */ -#define SAMA5D3_ID_TWI0 18 /* Two-Wire Interface 0 */ -#define SAMA5D3_ID_TWI1 19 /* Two-Wire Interface 1 */ -#define SAMA5D3_ID_TWI2 20 /* Two-Wire Interface 2 */ -#define SAMA5D3_ID_HSMCI0 21 /* MCI */ -#define SAMA5D3_ID_HSMCI1 22 /* MCI */ -#define SAMA5D3_ID_HSMCI2 23 /* MCI */ -#define SAMA5D3_ID_SPI0 24 /* Serial Peripheral Interface 0 */ -#define SAMA5D3_ID_SPI1 25 /* Serial Peripheral Interface 1 */ -#define SAMA5D3_ID_TC0 26 /* Timer Counter 0 */ -#define SAMA5D3_ID_TC1 27 /* Timer Counter 2 */ -#define SAMA5D3_ID_PWM 28 /* Pulse Width Modulation Controller */ -#define SAMA5D3_ID_ADC 29 /* Touch Screen ADC Controller */ -#define SAMA5D3_ID_DMA0 30 /* DMA Controller 0 */ -#define SAMA5D3_ID_DMA1 31 /* DMA Controller 1 */ -#define SAMA5D3_ID_UHPHS 32 /* USB Host High Speed */ -#define SAMA5D3_ID_UDPHS 33 /* USB Device High Speed */ -#define SAMA5D3_ID_GMAC 34 /* Gigabit Ethernet MAC */ -#define SAMA5D3_ID_EMAC 35 /* Ethernet MAC */ -#define SAMA5D3_ID_LCDC 36 /* LCD Controller */ -#define SAMA5D3_ID_ISI 37 /* Image Sensor Interface */ -#define SAMA5D3_ID_SSC0 38 /* Synchronous Serial Controller 0 */ -#define SAMA5D3_ID_SSC1 39 /* Synchronous Serial Controller 1 */ -#define SAMA5D3_ID_CAN0 40 /* CAN Controller 0 */ -#define SAMA5D3_ID_CAN1 41 /* CAN Controller 1 */ -#define SAMA5D3_ID_SHA 42 /* Secure Hash Algorithm */ -#define SAMA5D3_ID_AES 43 /* Advanced Encryption Standard */ -#define SAMA5D3_ID_TDES 44 /* Triple Data Encryption Standard */ -#define SAMA5D3_ID_TRNG 45 /* True Random Generator Number */ -#define SAMA5D3_ID_IRQ0 47 /* Advanced Interrupt Controller (IRQ0) */ - -/* - * User Peripheral physical base addresses. - */ -#define SAMA5D3_BASE_USART0 0xf001c000 -#define SAMA5D3_BASE_USART1 0xf0020000 -#define SAMA5D3_BASE_USART2 0xf8020000 -#define SAMA5D3_BASE_USART3 0xf8024000 - -/* - * System Peripherals - */ -#define SAMA5D3_BASE_RTC 0xfffffeb0 - -/* - * Internal Memory - */ -#define SAMA5D3_SRAM_BASE 0x00300000 /* Internal SRAM base address */ -#define SAMA5D3_SRAM_SIZE (128 * SZ_1K) /* Internal SRAM size (128Kb) */ - -#endif diff --git a/arch/arm/mach-at91/include/mach/sama5d4.h b/arch/arm/mach-at91/include/mach/sama5d4.h deleted file mode 100644 index f256a45d9854..000000000000 --- a/arch/arm/mach-at91/include/mach/sama5d4.h +++ /dev/null @@ -1,33 +0,0 @@ -/* - * Chip-specific header file for the SAMA5D4 family - * - * Copyright (C) 2013 Atmel Corporation, - * Nicolas Ferre - * - * Common definitions. - * Based on SAMA5D4 datasheet. - * - * Licensed under GPLv2 or later. - */ - -#ifndef SAMA5D4_H -#define SAMA5D4_H - -/* - * User Peripheral physical base addresses. - */ -#define SAMA5D4_BASE_USART3 0xfc00c000 /* (USART3 non-secure) Base Address */ -#define SAMA5D4_BASE_PMC 0xf0018000 /* (PMC) Base Address */ -#define SAMA5D4_BASE_MPDDRC 0xf0010000 /* (MPDDRC) Base Address */ -#define SAMA5D4_BASE_PIOD 0xfc068000 /* (PIOD) Base Address */ - -/* Some other peripherals */ -#define SAMA5D4_BASE_SYS2 SAMA5D4_BASE_PIOD - -/* - * Internal Memory. - */ -#define SAMA5D4_NS_SRAM_BASE 0x00210000 /* Internal SRAM base address Non-Secure */ -#define SAMA5D4_NS_SRAM_SIZE (64 * SZ_1K) /* Internal SRAM size Non-Secure part (64Kb) */ - -#endif diff --git a/arch/arm/mach-at91/include/mach/uncompress.h b/arch/arm/mach-at91/include/mach/uncompress.h deleted file mode 100644 index 4ebb609369e3..000000000000 --- a/arch/arm/mach-at91/include/mach/uncompress.h +++ /dev/null @@ -1,218 +0,0 @@ -/* - * arch/arm/mach-at91/include/mach/uncompress.h - * - * Copyright (C) 2003 SAN People - * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef __ASM_ARCH_UNCOMPRESS_H -#define __ASM_ARCH_UNCOMPRESS_H - -#include -#include -#include - -#include -#include - -void __iomem *at91_uart; - -static const u32 uarts_rm9200[] = { - AT91_BASE_DBGU0, - AT91RM9200_BASE_US0, - AT91RM9200_BASE_US1, - AT91RM9200_BASE_US2, - AT91RM9200_BASE_US3, - 0, -}; - -static const u32 uarts_sam9260[] = { - AT91_BASE_DBGU0, - AT91SAM9260_BASE_US0, - AT91SAM9260_BASE_US1, - AT91SAM9260_BASE_US2, - AT91SAM9260_BASE_US3, - AT91SAM9260_BASE_US4, - AT91SAM9260_BASE_US5, - 0, -}; - -static const u32 uarts_sam9261[] = { - AT91_BASE_DBGU0, - AT91SAM9261_BASE_US0, - AT91SAM9261_BASE_US1, - AT91SAM9261_BASE_US2, - 0, -}; - -static const u32 uarts_sam9263[] = { - AT91_BASE_DBGU1, - AT91SAM9263_BASE_US0, - AT91SAM9263_BASE_US1, - AT91SAM9263_BASE_US2, - 0, -}; - -static const u32 uarts_sam9g45[] = { - AT91_BASE_DBGU1, - AT91SAM9G45_BASE_US0, - AT91SAM9G45_BASE_US1, - AT91SAM9G45_BASE_US2, - AT91SAM9G45_BASE_US3, - 0, -}; - -static const u32 uarts_sam9rl[] = { - AT91_BASE_DBGU0, - AT91SAM9RL_BASE_US0, - AT91SAM9RL_BASE_US1, - AT91SAM9RL_BASE_US2, - AT91SAM9RL_BASE_US3, - 0, -}; - -static const u32 uarts_sam9x5[] = { - AT91_BASE_DBGU0, - AT91SAM9X5_BASE_USART0, - AT91SAM9X5_BASE_USART1, - AT91SAM9X5_BASE_USART2, - 0, -}; - -static const u32 uarts_sama5d3[] = { - AT91_BASE_DBGU1, - SAMA5D3_BASE_USART0, - SAMA5D3_BASE_USART1, - SAMA5D3_BASE_USART2, - SAMA5D3_BASE_USART3, - 0, -}; - -static const u32 uarts_sama5d4[] = { - AT91_BASE_DBGU2, - SAMA5D4_BASE_USART3, - 0, -}; - -static inline const u32* decomp_soc_detect(void __iomem *dbgu_base) -{ - u32 cidr, socid; - - cidr = __raw_readl(dbgu_base + AT91_DBGU_CIDR); - socid = cidr & ~AT91_CIDR_VERSION; - - switch (socid) { - case ARCH_ID_AT91RM9200: - return uarts_rm9200; - - case ARCH_ID_AT91SAM9G20: - case ARCH_ID_AT91SAM9260: - return uarts_sam9260; - - case ARCH_ID_AT91SAM9261: - return uarts_sam9261; - - case ARCH_ID_AT91SAM9263: - return uarts_sam9263; - - case ARCH_ID_AT91SAM9G45: - return uarts_sam9g45; - - case ARCH_ID_AT91SAM9RL64: - return uarts_sam9rl; - - case ARCH_ID_AT91SAM9N12: - case ARCH_ID_AT91SAM9X5: - return uarts_sam9x5; - - case ARCH_ID_SAMA5: - cidr = __raw_readl(dbgu_base + AT91_DBGU_EXID); - if (cidr & ARCH_EXID_SAMA5D3) - return uarts_sama5d3; - else if (cidr & ARCH_EXID_SAMA5D4) - return uarts_sama5d4; - - break; - } - - /* at91sam9g10 */ - if ((cidr & ~AT91_CIDR_EXT) == ARCH_ID_AT91SAM9G10) { - return uarts_sam9261; - } - /* at91sam9xe */ - else if ((cidr & AT91_CIDR_ARCH) == ARCH_FAMILY_AT91SAM9XE) { - return uarts_sam9260; - } - - return NULL; -} - -static inline void arch_decomp_setup(void) -{ - int i = 0; - const u32* usarts; - - usarts = decomp_soc_detect((void __iomem *)AT91_BASE_DBGU0); - if (!usarts) - usarts = decomp_soc_detect((void __iomem *)AT91_BASE_DBGU1); - if (!usarts) - usarts = decomp_soc_detect((void __iomem *)AT91_BASE_DBGU2); - if (!usarts) { - at91_uart = NULL; - return; - } - - do { - /* physical address */ - at91_uart = (void __iomem *)usarts[i]; - - if (__raw_readl(at91_uart + ATMEL_US_BRGR)) - return; - i++; - } while (usarts[i]); - - at91_uart = NULL; -} - -/* - * The following code assumes the serial port has already been - * initialized by the bootloader. If you didn't setup a port in - * your bootloader then nothing will appear (which might be desired). - * - * This does not append a newline - */ -static void putc(int c) -{ - if (!at91_uart) - return; - - while (!(__raw_readl(at91_uart + ATMEL_US_CSR) & ATMEL_US_TXRDY)) - barrier(); - __raw_writel(c, at91_uart + ATMEL_US_THR); -} - -static inline void flush(void) -{ - if (!at91_uart) - return; - - /* wait for transmission to complete */ - while (!(__raw_readl(at91_uart + ATMEL_US_CSR) & ATMEL_US_TXEMPTY)) - barrier(); -} - -#endif diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index aa4116e9452f..5062699cbb12 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -29,19 +29,26 @@ #include #include #include - -#include -#include +#include +#include #include "generic.h" #include "pm.h" +/* + * FIXME: this is needed to communicate between the pinctrl driver and + * the PM implementation in the machine. Possibly part of the PM + * implementation should be moved down into the pinctrl driver and get + * called as part of the generic suspend/resume path. + */ +extern void at91_pinctrl_gpio_suspend(void); +extern void at91_pinctrl_gpio_resume(void); + static struct { unsigned long uhp_udp_mask; int memctrl; } at91_pm_data; -static void (*at91_pm_standby)(void); void __iomem *at91_ramc_base[2]; static int at91_pm_valid_state(suspend_state_t state) @@ -119,76 +126,67 @@ int at91_suspend_entering_slow_clock(void) } EXPORT_SYMBOL(at91_suspend_entering_slow_clock); - -static void (*slow_clock)(void __iomem *pmc, void __iomem *ramc0, +static void (*at91_suspend_sram_fn)(void __iomem *pmc, void __iomem *ramc0, void __iomem *ramc1, int memctrl); -#ifdef CONFIG_AT91_SLOW_CLOCK -extern void at91_slow_clock(void __iomem *pmc, void __iomem *ramc0, +extern void at91_pm_suspend_in_sram(void __iomem *pmc, void __iomem *ramc0, void __iomem *ramc1, int memctrl); -extern u32 at91_slow_clock_sz; -#endif +extern u32 at91_pm_suspend_in_sram_sz; + +static void at91_pm_suspend(suspend_state_t state) +{ + unsigned int pm_data = at91_pm_data.memctrl; + + pm_data |= (state == PM_SUSPEND_MEM) ? + AT91_PM_MODE(AT91_PM_SLOW_CLOCK) : 0; + + flush_cache_all(); + outer_disable(); + + at91_suspend_sram_fn(at91_pmc_base, at91_ramc_base[0], + at91_ramc_base[1], pm_data); + + outer_resume(); +} static int at91_pm_enter(suspend_state_t state) { at91_pinctrl_gpio_suspend(); switch (state) { + /* + * Suspend-to-RAM is like STANDBY plus slow clock mode, so + * drivers must suspend more deeply, the master clock switches + * to the clk32k and turns off the main oscillator + */ + case PM_SUSPEND_MEM: /* - * Suspend-to-RAM is like STANDBY plus slow clock mode, so - * drivers must suspend more deeply: only the master clock - * controller may be using the main oscillator. + * Ensure that clocks are in a valid state. */ - case PM_SUSPEND_MEM: - /* - * Ensure that clocks are in a valid state. - */ - if (!at91_pm_verify_clocks()) - goto error; - - /* - * Enter slow clock mode by switching over to clk32k and - * turning off the main oscillator; reverse on wakeup. - */ - if (slow_clock) { -#ifdef CONFIG_AT91_SLOW_CLOCK - /* copy slow_clock handler to SRAM, and call it */ - memcpy(slow_clock, at91_slow_clock, at91_slow_clock_sz); -#endif - slow_clock(at91_pmc_base, at91_ramc_base[0], - at91_ramc_base[1], - at91_pm_data.memctrl); - break; - } else { - pr_info("AT91: PM - no slow clock mode enabled ...\n"); - /* FALLTHROUGH leaving master clock alone */ - } - - /* - * STANDBY mode has *all* drivers suspended; ignores irqs not - * marked as 'wakeup' event sources; and reduces DRAM power. - * But otherwise it's identical to PM_SUSPEND_ON: cpu idle, and - * nothing fancy done with main or cpu clocks. - */ - case PM_SUSPEND_STANDBY: - /* - * NOTE: the Wait-for-Interrupt instruction needs to be - * in icache so no SDRAM accesses are needed until the - * wakeup IRQ occurs and self-refresh is terminated. - * For ARM 926 based chips, this requirement is weaker - * as at91sam9 can access a RAM in self-refresh mode. - */ - if (at91_pm_standby) - at91_pm_standby(); - break; - - case PM_SUSPEND_ON: - cpu_do_idle(); - break; - - default: - pr_debug("AT91: PM - bogus suspend state %d\n", state); + if (!at91_pm_verify_clocks()) goto error; + + at91_pm_suspend(state); + + break; + + /* + * STANDBY mode has *all* drivers suspended; ignores irqs not + * marked as 'wakeup' event sources; and reduces DRAM power. + * But otherwise it's identical to PM_SUSPEND_ON: cpu idle, and + * nothing fancy done with main or cpu clocks. + */ + case PM_SUSPEND_STANDBY: + at91_pm_suspend(state); + break; + + case PM_SUSPEND_ON: + cpu_do_idle(); + break; + + default: + pr_debug("AT91: PM - bogus suspend state %d\n", state); + goto error; } error: @@ -218,12 +216,99 @@ static struct platform_device at91_cpuidle_device = { .name = "cpuidle-at91", }; -void at91_pm_set_standby(void (*at91_standby)(void)) +static void at91_pm_set_standby(void (*at91_standby)(void)) { - if (at91_standby) { + if (at91_standby) at91_cpuidle_device.dev.platform_data = at91_standby; - at91_pm_standby = at91_standby; +} + +/* + * The AT91RM9200 goes into self-refresh mode with this command, and will + * terminate self-refresh automatically on the next SDRAM access. + * + * Self-refresh mode is exited as soon as a memory access is made, but we don't + * know for sure when that happens. However, we need to restore the low-power + * mode if it was enabled before going idle. Restoring low-power mode while + * still in self-refresh is "not recommended", but seems to work. + */ +static void at91rm9200_standby(void) +{ + u32 lpr = at91_ramc_read(0, AT91RM9200_SDRAMC_LPR); + + asm volatile( + "b 1f\n\t" + ".align 5\n\t" + "1: mcr p15, 0, %0, c7, c10, 4\n\t" + " str %0, [%1, %2]\n\t" + " str %3, [%1, %4]\n\t" + " mcr p15, 0, %0, c7, c0, 4\n\t" + " str %5, [%1, %2]" + : + : "r" (0), "r" (at91_ramc_base[0]), "r" (AT91RM9200_SDRAMC_LPR), + "r" (1), "r" (AT91RM9200_SDRAMC_SRR), + "r" (lpr)); +} + +/* We manage both DDRAM/SDRAM controllers, we need more than one value to + * remember. + */ +static void at91_ddr_standby(void) +{ + /* Those two values allow us to delay self-refresh activation + * to the maximum. */ + u32 lpr0, lpr1 = 0; + u32 saved_lpr0, saved_lpr1 = 0; + + if (at91_ramc_base[1]) { + saved_lpr1 = at91_ramc_read(1, AT91_DDRSDRC_LPR); + lpr1 = saved_lpr1 & ~AT91_DDRSDRC_LPCB; + lpr1 |= AT91_DDRSDRC_LPCB_SELF_REFRESH; } + + saved_lpr0 = at91_ramc_read(0, AT91_DDRSDRC_LPR); + lpr0 = saved_lpr0 & ~AT91_DDRSDRC_LPCB; + lpr0 |= AT91_DDRSDRC_LPCB_SELF_REFRESH; + + /* self-refresh mode now */ + at91_ramc_write(0, AT91_DDRSDRC_LPR, lpr0); + if (at91_ramc_base[1]) + at91_ramc_write(1, AT91_DDRSDRC_LPR, lpr1); + + cpu_do_idle(); + + at91_ramc_write(0, AT91_DDRSDRC_LPR, saved_lpr0); + if (at91_ramc_base[1]) + at91_ramc_write(1, AT91_DDRSDRC_LPR, saved_lpr1); +} + +/* We manage both DDRAM/SDRAM controllers, we need more than one value to + * remember. + */ +static void at91sam9_sdram_standby(void) +{ + u32 lpr0, lpr1 = 0; + u32 saved_lpr0, saved_lpr1 = 0; + + if (at91_ramc_base[1]) { + saved_lpr1 = at91_ramc_read(1, AT91_SDRAMC_LPR); + lpr1 = saved_lpr1 & ~AT91_SDRAMC_LPCB; + lpr1 |= AT91_SDRAMC_LPCB_SELF_REFRESH; + } + + saved_lpr0 = at91_ramc_read(0, AT91_SDRAMC_LPR); + lpr0 = saved_lpr0 & ~AT91_SDRAMC_LPCB; + lpr0 |= AT91_SDRAMC_LPCB_SELF_REFRESH; + + /* self-refresh mode now */ + at91_ramc_write(0, AT91_SDRAMC_LPR, lpr0); + if (at91_ramc_base[1]) + at91_ramc_write(1, AT91_SDRAMC_LPR, lpr1); + + cpu_do_idle(); + + at91_ramc_write(0, AT91_SDRAMC_LPR, saved_lpr0); + if (at91_ramc_base[1]) + at91_ramc_write(1, AT91_SDRAMC_LPR, saved_lpr1); } static const struct of_device_id ramc_ids[] __initconst = { @@ -263,7 +348,6 @@ static __init void at91_dt_ramc(void) at91_pm_set_standby(standby); } -#ifdef CONFIG_AT91_SLOW_CLOCK static void __init at91_pm_sram_init(void) { struct gen_pool *sram_pool; @@ -291,30 +375,36 @@ static void __init at91_pm_sram_init(void) return; } - sram_base = gen_pool_alloc(sram_pool, at91_slow_clock_sz); + sram_base = gen_pool_alloc(sram_pool, at91_pm_suspend_in_sram_sz); if (!sram_base) { - pr_warn("%s: unable to alloc ocram!\n", __func__); + pr_warn("%s: unable to alloc sram!\n", __func__); return; } sram_pbase = gen_pool_virt_to_phys(sram_pool, sram_base); - slow_clock = __arm_ioremap_exec(sram_pbase, at91_slow_clock_sz, false); -} -#endif + at91_suspend_sram_fn = __arm_ioremap_exec(sram_pbase, + at91_pm_suspend_in_sram_sz, false); + if (!at91_suspend_sram_fn) { + pr_warn("SRAM: Could not map\n"); + return; + } + /* Copy the pm suspend handler to SRAM */ + at91_suspend_sram_fn = fncpy(at91_suspend_sram_fn, + &at91_pm_suspend_in_sram, at91_pm_suspend_in_sram_sz); +} static void __init at91_pm_init(void) { -#ifdef CONFIG_AT91_SLOW_CLOCK at91_pm_sram_init(); -#endif - - pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow clock mode)" : "")); if (at91_cpuidle_device.dev.platform_data) platform_device_register(&at91_cpuidle_device); - suspend_set_ops(&at91_pm_ops); + if (at91_suspend_sram_fn) + suspend_set_ops(&at91_pm_ops); + else + pr_info("AT91: PM not supported, due to no SRAM allocated\n"); } void __init at91rm9200_pm_init(void) diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h index 86c0aa819d25..ecd875a91d52 100644 --- a/arch/arm/mach-at91/pm.h +++ b/arch/arm/mach-at91/pm.h @@ -15,100 +15,16 @@ #include -#ifdef CONFIG_PM -extern void at91_pm_set_standby(void (*at91_standby)(void)); -#else -static inline void at91_pm_set_standby(void (*at91_standby)(void)) { } -#endif +#define AT91_MEMCTRL_MC 0 +#define AT91_MEMCTRL_SDRAMC 1 +#define AT91_MEMCTRL_DDRSDR 2 -/* - * The AT91RM9200 goes into self-refresh mode with this command, and will - * terminate self-refresh automatically on the next SDRAM access. - * - * Self-refresh mode is exited as soon as a memory access is made, but we don't - * know for sure when that happens. However, we need to restore the low-power - * mode if it was enabled before going idle. Restoring low-power mode while - * still in self-refresh is "not recommended", but seems to work. - */ +#define AT91_PM_MEMTYPE_MASK 0x0f -static inline void at91rm9200_standby(void) -{ - u32 lpr = at91_ramc_read(0, AT91RM9200_SDRAMC_LPR); +#define AT91_PM_MODE_OFFSET 4 +#define AT91_PM_MODE_MASK 0x01 +#define AT91_PM_MODE(x) (((x) & AT91_PM_MODE_MASK) << AT91_PM_MODE_OFFSET) - asm volatile( - "b 1f\n\t" - ".align 5\n\t" - "1: mcr p15, 0, %0, c7, c10, 4\n\t" - " str %0, [%1, %2]\n\t" - " str %3, [%1, %4]\n\t" - " mcr p15, 0, %0, c7, c0, 4\n\t" - " str %5, [%1, %2]" - : - : "r" (0), "r" (at91_ramc_base[0]), "r" (AT91RM9200_SDRAMC_LPR), - "r" (1), "r" (AT91RM9200_SDRAMC_SRR), - "r" (lpr)); -} - -/* We manage both DDRAM/SDRAM controllers, we need more than one value to - * remember. - */ -static inline void at91_ddr_standby(void) -{ - /* Those two values allow us to delay self-refresh activation - * to the maximum. */ - u32 lpr0, lpr1 = 0; - u32 saved_lpr0, saved_lpr1 = 0; - - if (at91_ramc_base[1]) { - saved_lpr1 = at91_ramc_read(1, AT91_DDRSDRC_LPR); - lpr1 = saved_lpr1 & ~AT91_DDRSDRC_LPCB; - lpr1 |= AT91_DDRSDRC_LPCB_SELF_REFRESH; - } - - saved_lpr0 = at91_ramc_read(0, AT91_DDRSDRC_LPR); - lpr0 = saved_lpr0 & ~AT91_DDRSDRC_LPCB; - lpr0 |= AT91_DDRSDRC_LPCB_SELF_REFRESH; - - /* self-refresh mode now */ - at91_ramc_write(0, AT91_DDRSDRC_LPR, lpr0); - if (at91_ramc_base[1]) - at91_ramc_write(1, AT91_DDRSDRC_LPR, lpr1); - - cpu_do_idle(); - - at91_ramc_write(0, AT91_DDRSDRC_LPR, saved_lpr0); - if (at91_ramc_base[1]) - at91_ramc_write(1, AT91_DDRSDRC_LPR, saved_lpr1); -} - -/* We manage both DDRAM/SDRAM controllers, we need more than one value to - * remember. - */ -static inline void at91sam9_sdram_standby(void) -{ - u32 lpr0, lpr1 = 0; - u32 saved_lpr0, saved_lpr1 = 0; - - if (at91_ramc_base[1]) { - saved_lpr1 = at91_ramc_read(1, AT91_SDRAMC_LPR); - lpr1 = saved_lpr1 & ~AT91_SDRAMC_LPCB; - lpr1 |= AT91_SDRAMC_LPCB_SELF_REFRESH; - } - - saved_lpr0 = at91_ramc_read(0, AT91_SDRAMC_LPR); - lpr0 = saved_lpr0 & ~AT91_SDRAMC_LPCB; - lpr0 |= AT91_SDRAMC_LPCB_SELF_REFRESH; - - /* self-refresh mode now */ - at91_ramc_write(0, AT91_SDRAMC_LPR, lpr0); - if (at91_ramc_base[1]) - at91_ramc_write(1, AT91_SDRAMC_LPR, lpr1); - - cpu_do_idle(); - - at91_ramc_write(0, AT91_SDRAMC_LPR, saved_lpr0); - if (at91_ramc_base[1]) - at91_ramc_write(1, AT91_SDRAMC_LPR, saved_lpr1); -} +#define AT91_PM_SLOW_CLOCK 0x01 #endif diff --git a/arch/arm/mach-at91/pm_slowclock.S b/arch/arm/mach-at91/pm_slowclock.S deleted file mode 100644 index 931f0e302c03..000000000000 --- a/arch/arm/mach-at91/pm_slowclock.S +++ /dev/null @@ -1,335 +0,0 @@ -/* - * arch/arm/mach-at91/pm_slow_clock.S - * - * Copyright (C) 2006 Savin Zlobec - * - * AT91SAM9 support: - * Copyright (C) 2007 Anti Sullin -#include -#include -#include - -/* - * When SLOWDOWN_MASTER_CLOCK is defined we will also slow down the Master - * clock during suspend by adjusting its prescalar and divisor. - * NOTE: This hasn't been shown to be stable on SAM9s; and on the RM9200 there - * are errata regarding adjusting the prescalar and divisor. - */ -#undef SLOWDOWN_MASTER_CLOCK - -pmc .req r0 -sdramc .req r1 -ramc1 .req r2 -memctrl .req r3 -tmp1 .req r4 -tmp2 .req r5 - -/* - * Wait until master clock is ready (after switching master clock source) - */ - .macro wait_mckrdy -1: ldr tmp1, [pmc, #AT91_PMC_SR] - tst tmp1, #AT91_PMC_MCKRDY - beq 1b - .endm - -/* - * Wait until master oscillator has stabilized. - */ - .macro wait_moscrdy -1: ldr tmp1, [pmc, #AT91_PMC_SR] - tst tmp1, #AT91_PMC_MOSCS - beq 1b - .endm - -/* - * Wait until PLLA has locked. - */ - .macro wait_pllalock -1: ldr tmp1, [pmc, #AT91_PMC_SR] - tst tmp1, #AT91_PMC_LOCKA - beq 1b - .endm - -/* - * Wait until PLLB has locked. - */ - .macro wait_pllblock -1: ldr tmp1, [pmc, #AT91_PMC_SR] - tst tmp1, #AT91_PMC_LOCKB - beq 1b - .endm - - .text - - .arm - -/* void at91_slow_clock(void __iomem *pmc, void __iomem *sdramc, - * void __iomem *ramc1, int memctrl) - */ -ENTRY(at91_slow_clock) - /* Save registers on stack */ - stmfd sp!, {r4 - r12, lr} - - /* - * Register usage: - * R0 = Base address of AT91_PMC - * R1 = Base address of RAM Controller (SDRAM, DDRSDR, or AT91_SYS) - * R2 = Base address of second RAM Controller or 0 if not present - * R3 = Memory controller - * R4 = temporary register - * R5 = temporary register - */ - - /* Drain write buffer */ - mov tmp1, #0 - mcr p15, 0, tmp1, c7, c10, 4 - - cmp memctrl, #AT91_MEMCTRL_MC - bne ddr_sr_enable - - /* - * at91rm9200 Memory controller - */ - /* Put SDRAM in self-refresh mode */ - mov tmp1, #1 - str tmp1, [sdramc, #AT91RM9200_SDRAMC_SRR] - b sdr_sr_done - - /* - * DDRSDR Memory controller - */ -ddr_sr_enable: - cmp memctrl, #AT91_MEMCTRL_DDRSDR - bne sdr_sr_enable - - /* LPDDR1 --> force DDR2 mode during self-refresh */ - ldr tmp1, [sdramc, #AT91_DDRSDRC_MDR] - str tmp1, .saved_sam9_mdr - bic tmp1, tmp1, #~AT91_DDRSDRC_MD - cmp tmp1, #AT91_DDRSDRC_MD_LOW_POWER_DDR - ldreq tmp1, [sdramc, #AT91_DDRSDRC_MDR] - biceq tmp1, tmp1, #AT91_DDRSDRC_MD - orreq tmp1, tmp1, #AT91_DDRSDRC_MD_DDR2 - streq tmp1, [sdramc, #AT91_DDRSDRC_MDR] - - /* prepare for DDRAM self-refresh mode */ - ldr tmp1, [sdramc, #AT91_DDRSDRC_LPR] - str tmp1, .saved_sam9_lpr - bic tmp1, #AT91_DDRSDRC_LPCB - orr tmp1, #AT91_DDRSDRC_LPCB_SELF_REFRESH - - /* figure out if we use the second ram controller */ - cmp ramc1, #0 - beq ddr_no_2nd_ctrl - - ldr tmp2, [ramc1, #AT91_DDRSDRC_MDR] - str tmp2, .saved_sam9_mdr1 - bic tmp2, tmp2, #~AT91_DDRSDRC_MD - cmp tmp2, #AT91_DDRSDRC_MD_LOW_POWER_DDR - ldreq tmp2, [ramc1, #AT91_DDRSDRC_MDR] - biceq tmp2, tmp2, #AT91_DDRSDRC_MD - orreq tmp2, tmp2, #AT91_DDRSDRC_MD_DDR2 - streq tmp2, [ramc1, #AT91_DDRSDRC_MDR] - - ldr tmp2, [ramc1, #AT91_DDRSDRC_LPR] - str tmp2, .saved_sam9_lpr1 - bic tmp2, #AT91_DDRSDRC_LPCB - orr tmp2, #AT91_DDRSDRC_LPCB_SELF_REFRESH - - /* Enable DDRAM self-refresh mode */ - str tmp2, [ramc1, #AT91_DDRSDRC_LPR] -ddr_no_2nd_ctrl: - str tmp1, [sdramc, #AT91_DDRSDRC_LPR] - - b sdr_sr_done - - /* - * SDRAMC Memory controller - */ -sdr_sr_enable: - /* Enable SDRAM self-refresh mode */ - ldr tmp1, [sdramc, #AT91_SDRAMC_LPR] - str tmp1, .saved_sam9_lpr - - bic tmp1, #AT91_SDRAMC_LPCB - orr tmp1, #AT91_SDRAMC_LPCB_SELF_REFRESH - str tmp1, [sdramc, #AT91_SDRAMC_LPR] - -sdr_sr_done: - /* Save Master clock setting */ - ldr tmp1, [pmc, #AT91_PMC_MCKR] - str tmp1, .saved_mckr - - /* - * Set the Master clock source to slow clock - */ - bic tmp1, tmp1, #AT91_PMC_CSS - str tmp1, [pmc, #AT91_PMC_MCKR] - - wait_mckrdy - -#ifdef SLOWDOWN_MASTER_CLOCK - /* - * Set the Master Clock PRES and MDIV fields. - * - * See AT91RM9200 errata #27 and #28 for details. - */ - mov tmp1, #0 - str tmp1, [pmc, #AT91_PMC_MCKR] - - wait_mckrdy -#endif - - /* Save PLLA setting and disable it */ - ldr tmp1, [pmc, #AT91_CKGR_PLLAR] - str tmp1, .saved_pllar - - mov tmp1, #AT91_PMC_PLLCOUNT - orr tmp1, tmp1, #(1 << 29) /* bit 29 always set */ - str tmp1, [pmc, #AT91_CKGR_PLLAR] - - /* Save PLLB setting and disable it */ - ldr tmp1, [pmc, #AT91_CKGR_PLLBR] - str tmp1, .saved_pllbr - - mov tmp1, #AT91_PMC_PLLCOUNT - str tmp1, [pmc, #AT91_CKGR_PLLBR] - - /* Turn off the main oscillator */ - ldr tmp1, [pmc, #AT91_CKGR_MOR] - bic tmp1, tmp1, #AT91_PMC_MOSCEN - orr tmp1, tmp1, #AT91_PMC_KEY - str tmp1, [pmc, #AT91_CKGR_MOR] - - /* Wait for interrupt */ - mcr p15, 0, tmp1, c7, c0, 4 - - /* Turn on the main oscillator */ - ldr tmp1, [pmc, #AT91_CKGR_MOR] - orr tmp1, tmp1, #AT91_PMC_MOSCEN - orr tmp1, tmp1, #AT91_PMC_KEY - str tmp1, [pmc, #AT91_CKGR_MOR] - - wait_moscrdy - - /* Restore PLLB setting */ - ldr tmp1, .saved_pllbr - str tmp1, [pmc, #AT91_CKGR_PLLBR] - - tst tmp1, #(AT91_PMC_MUL & 0xff0000) - bne 1f - tst tmp1, #(AT91_PMC_MUL & ~0xff0000) - beq 2f -1: - wait_pllblock -2: - - /* Restore PLLA setting */ - ldr tmp1, .saved_pllar - str tmp1, [pmc, #AT91_CKGR_PLLAR] - - tst tmp1, #(AT91_PMC_MUL & 0xff0000) - bne 3f - tst tmp1, #(AT91_PMC_MUL & ~0xff0000) - beq 4f -3: - wait_pllalock -4: - -#ifdef SLOWDOWN_MASTER_CLOCK - /* - * First set PRES if it was not 0, - * than set CSS and MDIV fields. - * - * See AT91RM9200 errata #27 and #28 for details. - */ - ldr tmp1, .saved_mckr - tst tmp1, #AT91_PMC_PRES - beq 2f - and tmp1, tmp1, #AT91_PMC_PRES - str tmp1, [pmc, #AT91_PMC_MCKR] - - wait_mckrdy -#endif - - /* - * Restore master clock setting - */ -2: ldr tmp1, .saved_mckr - str tmp1, [pmc, #AT91_PMC_MCKR] - - wait_mckrdy - - /* - * at91rm9200 Memory controller - * Do nothing - self-refresh is automatically disabled. - */ - cmp memctrl, #AT91_MEMCTRL_MC - beq ram_restored - - /* - * DDRSDR Memory controller - */ - cmp memctrl, #AT91_MEMCTRL_DDRSDR - bne sdr_en_restore - /* Restore MDR in case of LPDDR1 */ - ldr tmp1, .saved_sam9_mdr - str tmp1, [sdramc, #AT91_DDRSDRC_MDR] - /* Restore LPR on AT91 with DDRAM */ - ldr tmp1, .saved_sam9_lpr - str tmp1, [sdramc, #AT91_DDRSDRC_LPR] - - /* if we use the second ram controller */ - cmp ramc1, #0 - ldrne tmp2, .saved_sam9_mdr1 - strne tmp2, [ramc1, #AT91_DDRSDRC_MDR] - ldrne tmp2, .saved_sam9_lpr1 - strne tmp2, [ramc1, #AT91_DDRSDRC_LPR] - - b ram_restored - - /* - * SDRAMC Memory controller - */ -sdr_en_restore: - /* Restore LPR on AT91 with SDRAM */ - ldr tmp1, .saved_sam9_lpr - str tmp1, [sdramc, #AT91_SDRAMC_LPR] - -ram_restored: - /* Restore registers, and return */ - ldmfd sp!, {r4 - r12, pc} - - -.saved_mckr: - .word 0 - -.saved_pllar: - .word 0 - -.saved_pllbr: - .word 0 - -.saved_sam9_lpr: - .word 0 - -.saved_sam9_lpr1: - .word 0 - -.saved_sam9_mdr: - .word 0 - -.saved_sam9_mdr1: - .word 0 - -ENTRY(at91_slow_clock_sz) - .word .-at91_slow_clock diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_suspend.S new file mode 100644 index 000000000000..bd22b2c8a051 --- /dev/null +++ b/arch/arm/mach-at91/pm_suspend.S @@ -0,0 +1,337 @@ +/* + * arch/arm/mach-at91/pm_slow_clock.S + * + * Copyright (C) 2006 Savin Zlobec + * + * AT91SAM9 support: + * Copyright (C) 2007 Anti Sullin +#include +#include +#include "pm.h" + +#define SRAMC_SELF_FRESH_ACTIVE 0x01 +#define SRAMC_SELF_FRESH_EXIT 0x00 + +pmc .req r0 +tmp1 .req r4 +tmp2 .req r5 + +/* + * Wait until master clock is ready (after switching master clock source) + */ + .macro wait_mckrdy +1: ldr tmp1, [pmc, #AT91_PMC_SR] + tst tmp1, #AT91_PMC_MCKRDY + beq 1b + .endm + +/* + * Wait until master oscillator has stabilized. + */ + .macro wait_moscrdy +1: ldr tmp1, [pmc, #AT91_PMC_SR] + tst tmp1, #AT91_PMC_MOSCS + beq 1b + .endm + +/* + * Wait until PLLA has locked. + */ + .macro wait_pllalock +1: ldr tmp1, [pmc, #AT91_PMC_SR] + tst tmp1, #AT91_PMC_LOCKA + beq 1b + .endm + +/* + * Put the processor to enter the idle state + */ + .macro at91_cpu_idle + +#if defined(CONFIG_CPU_V7) + mov tmp1, #AT91_PMC_PCK + str tmp1, [pmc, #AT91_PMC_SCDR] + + dsb + + wfi @ Wait For Interrupt +#else + mcr p15, 0, tmp1, c7, c0, 4 +#endif + + .endm + + .text + + .arm + +/* + * void at91_pm_suspend_in_sram(void __iomem *pmc, void __iomem *sdramc, + * void __iomem *ramc1, int memctrl) + * @input param: + * @r0: base address of AT91_PMC + * @r1: base address of SDRAM Controller (SDRAM, DDRSDR, or AT91_SYS) + * @r2: base address of second SDRAM Controller or 0 if not present + * @r3: pm information + */ +ENTRY(at91_pm_suspend_in_sram) + /* Save registers on stack */ + stmfd sp!, {r4 - r12, lr} + + /* Drain write buffer */ + mov tmp1, #0 + mcr p15, 0, tmp1, c7, c10, 4 + + str r0, .pmc_base + str r1, .sramc_base + str r2, .sramc1_base + + and r0, r3, #AT91_PM_MEMTYPE_MASK + str r0, .memtype + + lsr r0, r3, #AT91_PM_MODE_OFFSET + and r0, r0, #AT91_PM_MODE_MASK + str r0, .pm_mode + + /* Active the self-refresh mode */ + mov r0, #SRAMC_SELF_FRESH_ACTIVE + bl at91_sramc_self_refresh + + ldr r0, .pm_mode + tst r0, #AT91_PM_SLOW_CLOCK + beq skip_disable_main_clock + + ldr pmc, .pmc_base + + /* Save Master clock setting */ + ldr tmp1, [pmc, #AT91_PMC_MCKR] + str tmp1, .saved_mckr + + /* + * Set the Master clock source to slow clock + */ + bic tmp1, tmp1, #AT91_PMC_CSS + str tmp1, [pmc, #AT91_PMC_MCKR] + + wait_mckrdy + + /* Save PLLA setting and disable it */ + ldr tmp1, [pmc, #AT91_CKGR_PLLAR] + str tmp1, .saved_pllar + + mov tmp1, #AT91_PMC_PLLCOUNT + orr tmp1, tmp1, #(1 << 29) /* bit 29 always set */ + str tmp1, [pmc, #AT91_CKGR_PLLAR] + + /* Turn off the main oscillator */ + ldr tmp1, [pmc, #AT91_CKGR_MOR] + bic tmp1, tmp1, #AT91_PMC_MOSCEN + orr tmp1, tmp1, #AT91_PMC_KEY + str tmp1, [pmc, #AT91_CKGR_MOR] + +skip_disable_main_clock: + ldr pmc, .pmc_base + + /* Wait for interrupt */ + at91_cpu_idle + + ldr r0, .pm_mode + tst r0, #AT91_PM_SLOW_CLOCK + beq skip_enable_main_clock + + ldr pmc, .pmc_base + + /* Turn on the main oscillator */ + ldr tmp1, [pmc, #AT91_CKGR_MOR] + orr tmp1, tmp1, #AT91_PMC_MOSCEN + orr tmp1, tmp1, #AT91_PMC_KEY + str tmp1, [pmc, #AT91_CKGR_MOR] + + wait_moscrdy + + /* Restore PLLA setting */ + ldr tmp1, .saved_pllar + str tmp1, [pmc, #AT91_CKGR_PLLAR] + + tst tmp1, #(AT91_PMC_MUL & 0xff0000) + bne 3f + tst tmp1, #(AT91_PMC_MUL & ~0xff0000) + beq 4f +3: + wait_pllalock +4: + + /* + * Restore master clock setting + */ + ldr tmp1, .saved_mckr + str tmp1, [pmc, #AT91_PMC_MCKR] + + wait_mckrdy + +skip_enable_main_clock: + /* Exit the self-refresh mode */ + mov r0, #SRAMC_SELF_FRESH_EXIT + bl at91_sramc_self_refresh + + /* Restore registers, and return */ + ldmfd sp!, {r4 - r12, pc} +ENDPROC(at91_pm_suspend_in_sram) + +/* + * void at91_sramc_self_refresh(unsigned int is_active) + * + * @input param: + * @r0: 1 - active self-refresh mode + * 0 - exit self-refresh mode + * register usage: + * @r1: memory type + * @r2: base address of the sram controller + */ + +ENTRY(at91_sramc_self_refresh) + ldr r1, .memtype + ldr r2, .sramc_base + + cmp r1, #AT91_MEMCTRL_MC + bne ddrc_sf + + /* + * at91rm9200 Memory controller + */ + + /* + * For exiting the self-refresh mode, do nothing, + * automatically exit the self-refresh mode. + */ + tst r0, #SRAMC_SELF_FRESH_ACTIVE + beq exit_sramc_sf + + /* Active SDRAM self-refresh mode */ + mov r3, #1 + str r3, [r2, #AT91RM9200_SDRAMC_SRR] + b exit_sramc_sf + +ddrc_sf: + cmp r1, #AT91_MEMCTRL_DDRSDR + bne sdramc_sf + + /* + * DDR Memory controller + */ + tst r0, #SRAMC_SELF_FRESH_ACTIVE + beq ddrc_exit_sf + + /* LPDDR1 --> force DDR2 mode during self-refresh */ + ldr r3, [r2, #AT91_DDRSDRC_MDR] + str r3, .saved_sam9_mdr + bic r3, r3, #~AT91_DDRSDRC_MD + cmp r3, #AT91_DDRSDRC_MD_LOW_POWER_DDR + ldreq r3, [r2, #AT91_DDRSDRC_MDR] + biceq r3, r3, #AT91_DDRSDRC_MD + orreq r3, r3, #AT91_DDRSDRC_MD_DDR2 + streq r3, [r2, #AT91_DDRSDRC_MDR] + + /* Active DDRC self-refresh mode */ + ldr r3, [r2, #AT91_DDRSDRC_LPR] + str r3, .saved_sam9_lpr + bic r3, r3, #AT91_DDRSDRC_LPCB + orr r3, r3, #AT91_DDRSDRC_LPCB_SELF_REFRESH + str r3, [r2, #AT91_DDRSDRC_LPR] + + /* If using the 2nd ddr controller */ + ldr r2, .sramc1_base + cmp r2, #0 + beq no_2nd_ddrc + + ldr r3, [r2, #AT91_DDRSDRC_MDR] + str r3, .saved_sam9_mdr1 + bic r3, r3, #~AT91_DDRSDRC_MD + cmp r3, #AT91_DDRSDRC_MD_LOW_POWER_DDR + ldreq r3, [r2, #AT91_DDRSDRC_MDR] + biceq r3, r3, #AT91_DDRSDRC_MD + orreq r3, r3, #AT91_DDRSDRC_MD_DDR2 + streq r3, [r2, #AT91_DDRSDRC_MDR] + + /* Active DDRC self-refresh mode */ + ldr r3, [r2, #AT91_DDRSDRC_LPR] + str r3, .saved_sam9_lpr1 + bic r3, r3, #AT91_DDRSDRC_LPCB + orr r3, r3, #AT91_DDRSDRC_LPCB_SELF_REFRESH + str r3, [r2, #AT91_DDRSDRC_LPR] + +no_2nd_ddrc: + b exit_sramc_sf + +ddrc_exit_sf: + /* Restore MDR in case of LPDDR1 */ + ldr r3, .saved_sam9_mdr + str r3, [r2, #AT91_DDRSDRC_MDR] + /* Restore LPR on AT91 with DDRAM */ + ldr r3, .saved_sam9_lpr + str r3, [r2, #AT91_DDRSDRC_LPR] + + /* If using the 2nd ddr controller */ + ldr r2, .sramc1_base + cmp r2, #0 + ldrne r3, .saved_sam9_mdr1 + strne r3, [r2, #AT91_DDRSDRC_MDR] + ldrne r3, .saved_sam9_lpr1 + strne r3, [r2, #AT91_DDRSDRC_LPR] + + b exit_sramc_sf + + /* + * SDRAMC Memory controller + */ +sdramc_sf: + tst r0, #SRAMC_SELF_FRESH_ACTIVE + beq sdramc_exit_sf + + /* Active SDRAMC self-refresh mode */ + ldr r3, [r2, #AT91_SDRAMC_LPR] + str r3, .saved_sam9_lpr + bic r3, r3, #AT91_SDRAMC_LPCB + orr r3, r3, #AT91_SDRAMC_LPCB_SELF_REFRESH + str r3, [r2, #AT91_SDRAMC_LPR] + +sdramc_exit_sf: + ldr r3, .saved_sam9_lpr + str r3, [r2, #AT91_SDRAMC_LPR] + +exit_sramc_sf: + mov pc, lr +ENDPROC(at91_sramc_self_refresh) + +.pmc_base: + .word 0 +.sramc_base: + .word 0 +.sramc1_base: + .word 0 +.memtype: + .word 0 +.pm_mode: + .word 0 +.saved_mckr: + .word 0 +.saved_pllar: + .word 0 +.saved_sam9_lpr: + .word 0 +.saved_sam9_lpr1: + .word 0 +.saved_sam9_mdr: + .word 0 +.saved_sam9_mdr1: + .word 0 + +ENTRY(at91_pm_suspend_in_sram_sz) + .word .-at91_pm_suspend_in_sram diff --git a/arch/arm/mach-at91/sama5.c b/arch/arm/mach-at91/sama5.c index 03dcb441f3d2..41d829d8e7d5 100644 --- a/arch/arm/mach-at91/sama5.c +++ b/arch/arm/mach-at91/sama5.c @@ -7,48 +7,48 @@ * Licensed under GPLv2 or later. */ -#include -#include -#include -#include -#include #include -#include #include -#include -#include -#include -#include - -#include -#include #include #include -#include +#include #include "generic.h" +#include "soc.h" -static int ksz8081_phy_fixup(struct phy_device *phy) -{ - int value; - - value = phy_read(phy, 0x16); - value &= ~0x20; - phy_write(phy, 0x16, value); - - return 0; -} +static const struct at91_soc sama5_socs[] = { + AT91_SOC(SAMA5D3_CIDR_MATCH, SAMA5D31_EXID_MATCH, + "sama5d31", "sama5d3"), + AT91_SOC(SAMA5D3_CIDR_MATCH, SAMA5D33_EXID_MATCH, + "sama5d33", "sama5d3"), + AT91_SOC(SAMA5D3_CIDR_MATCH, SAMA5D34_EXID_MATCH, + "sama5d34", "sama5d3"), + AT91_SOC(SAMA5D3_CIDR_MATCH, SAMA5D35_EXID_MATCH, + "sama5d35", "sama5d3"), + AT91_SOC(SAMA5D3_CIDR_MATCH, SAMA5D36_EXID_MATCH, + "sama5d36", "sama5d3"), + AT91_SOC(SAMA5D4_CIDR_MATCH, SAMA5D41_EXID_MATCH, + "sama5d41", "sama5d4"), + AT91_SOC(SAMA5D4_CIDR_MATCH, SAMA5D42_EXID_MATCH, + "sama5d42", "sama5d4"), + AT91_SOC(SAMA5D4_CIDR_MATCH, SAMA5D43_EXID_MATCH, + "sama5d43", "sama5d4"), + AT91_SOC(SAMA5D4_CIDR_MATCH, SAMA5D44_EXID_MATCH, + "sama5d44", "sama5d4"), + { /* sentinel */ }, +}; static void __init sama5_dt_device_init(void) { - if (of_machine_is_compatible("atmel,sama5d4ek") && - IS_ENABLED(CONFIG_PHYLIB)) { - phy_register_fixup_for_id("fc028000.etherne:00", - ksz8081_phy_fixup); - } + struct soc_device *soc; + struct device *soc_dev = NULL; - of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); + soc = at91_soc_init(sama5_socs); + if (soc != NULL) + soc_dev = soc_device_to_device(soc); + + of_platform_populate(NULL, of_default_bus_match_table, NULL, soc_dev); at91sam9x5_pm_init(); } @@ -59,44 +59,10 @@ static const char *sama5_dt_board_compat[] __initconst = { DT_MACHINE_START(sama5_dt, "Atmel SAMA5") /* Maintainer: Atmel */ - .map_io = at91_map_io, .init_machine = sama5_dt_device_init, .dt_compat = sama5_dt_board_compat, MACHINE_END -static struct map_desc at91_io_desc[] __initdata = { - { - .virtual = (unsigned long)AT91_ALT_IO_P2V(SAMA5D4_BASE_MPDDRC), - .pfn = __phys_to_pfn(SAMA5D4_BASE_MPDDRC), - .length = SZ_512, - .type = MT_DEVICE, - }, - { - .virtual = (unsigned long)AT91_ALT_IO_P2V(SAMA5D4_BASE_PMC), - .pfn = __phys_to_pfn(SAMA5D4_BASE_PMC), - .length = SZ_512, - .type = MT_DEVICE, - }, - { /* On sama5d4, we use USART3 as serial console */ - .virtual = (unsigned long)AT91_ALT_IO_P2V(SAMA5D4_BASE_USART3), - .pfn = __phys_to_pfn(SAMA5D4_BASE_USART3), - .length = SZ_256, - .type = MT_DEVICE, - }, - { /* A bunch of peripheral with fine grained IO space */ - .virtual = (unsigned long)AT91_ALT_IO_P2V(SAMA5D4_BASE_SYS2), - .pfn = __phys_to_pfn(SAMA5D4_BASE_SYS2), - .length = SZ_2K, - .type = MT_DEVICE, - }, -}; - -static void __init sama5_alt_map_io(void) -{ - at91_alt_map_io(); - iotable_init(at91_io_desc, ARRAY_SIZE(at91_io_desc)); -} - static const char *sama5_alt_dt_board_compat[] __initconst = { "atmel,sama5d4", NULL @@ -104,7 +70,6 @@ static const char *sama5_alt_dt_board_compat[] __initconst = { DT_MACHINE_START(sama5_alt_dt, "Atmel SAMA5") /* Maintainer: Atmel */ - .map_io = sama5_alt_map_io, .init_machine = sama5_dt_device_init, .dt_compat = sama5_alt_dt_board_compat, .l2c_aux_mask = ~0UL, diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c deleted file mode 100644 index 4e58bc90ed21..000000000000 --- a/arch/arm/mach-at91/setup.c +++ /dev/null @@ -1,330 +0,0 @@ -/* - * Copyright (C) 2007 Atmel Corporation. - * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD - * - * Under GPLv2 - */ - -#define pr_fmt(fmt) "AT91: " fmt - -#include -#include -#include -#include -#include -#include -#include - -#include -#include - -#include -#include -#include - -#include "generic.h" -#include "pm.h" - -struct at91_socinfo at91_soc_initdata; -EXPORT_SYMBOL(at91_soc_initdata); - -static struct map_desc at91_io_desc __initdata __maybe_unused = { - .virtual = (unsigned long)AT91_VA_BASE_SYS, - .pfn = __phys_to_pfn(AT91_BASE_SYS), - .length = SZ_16K, - .type = MT_DEVICE, -}; - -static struct map_desc at91_alt_io_desc __initdata __maybe_unused = { - .virtual = (unsigned long)AT91_ALT_VA_BASE_SYS, - .pfn = __phys_to_pfn(AT91_ALT_BASE_SYS), - .length = 24 * SZ_1K, - .type = MT_DEVICE, -}; - -static void __init soc_detect(u32 dbgu_base) -{ - u32 cidr, socid; - - cidr = __raw_readl(AT91_IO_P2V(dbgu_base) + AT91_DBGU_CIDR); - socid = cidr & ~AT91_CIDR_VERSION; - - switch (socid) { - case ARCH_ID_AT91RM9200: - at91_soc_initdata.type = AT91_SOC_RM9200; - if (at91_soc_initdata.subtype == AT91_SOC_SUBTYPE_UNKNOWN) - at91_soc_initdata.subtype = AT91_SOC_RM9200_BGA; - break; - - case ARCH_ID_AT91SAM9260: - at91_soc_initdata.type = AT91_SOC_SAM9260; - at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE; - break; - - case ARCH_ID_AT91SAM9261: - at91_soc_initdata.type = AT91_SOC_SAM9261; - at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE; - break; - - case ARCH_ID_AT91SAM9263: - at91_soc_initdata.type = AT91_SOC_SAM9263; - at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE; - break; - - case ARCH_ID_AT91SAM9G20: - at91_soc_initdata.type = AT91_SOC_SAM9G20; - at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE; - break; - - case ARCH_ID_AT91SAM9G45: - at91_soc_initdata.type = AT91_SOC_SAM9G45; - if (cidr == ARCH_ID_AT91SAM9G45ES) - at91_soc_initdata.subtype = AT91_SOC_SAM9G45ES; - break; - - case ARCH_ID_AT91SAM9RL64: - at91_soc_initdata.type = AT91_SOC_SAM9RL; - at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE; - break; - - case ARCH_ID_AT91SAM9X5: - at91_soc_initdata.type = AT91_SOC_SAM9X5; - break; - - case ARCH_ID_AT91SAM9N12: - at91_soc_initdata.type = AT91_SOC_SAM9N12; - break; - - case ARCH_ID_SAMA5: - at91_soc_initdata.exid = __raw_readl(AT91_IO_P2V(dbgu_base) + AT91_DBGU_EXID); - if (at91_soc_initdata.exid & ARCH_EXID_SAMA5D3) { - at91_soc_initdata.type = AT91_SOC_SAMA5D3; - } - break; - } - - /* at91sam9g10 */ - if ((socid & ~AT91_CIDR_EXT) == ARCH_ID_AT91SAM9G10) { - at91_soc_initdata.type = AT91_SOC_SAM9G10; - at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE; - } - /* at91sam9xe */ - else if ((cidr & AT91_CIDR_ARCH) == ARCH_FAMILY_AT91SAM9XE) { - at91_soc_initdata.type = AT91_SOC_SAM9260; - at91_soc_initdata.subtype = AT91_SOC_SAM9XE; - } - - if (!at91_soc_is_detected()) - return; - - at91_soc_initdata.cidr = cidr; - - /* sub version of soc */ - if (!at91_soc_initdata.exid) - at91_soc_initdata.exid = __raw_readl(AT91_IO_P2V(dbgu_base) + AT91_DBGU_EXID); - - if (at91_soc_initdata.type == AT91_SOC_SAM9G45) { - switch (at91_soc_initdata.exid) { - case ARCH_EXID_AT91SAM9M10: - at91_soc_initdata.subtype = AT91_SOC_SAM9M10; - break; - case ARCH_EXID_AT91SAM9G46: - at91_soc_initdata.subtype = AT91_SOC_SAM9G46; - break; - case ARCH_EXID_AT91SAM9M11: - at91_soc_initdata.subtype = AT91_SOC_SAM9M11; - break; - } - } - - if (at91_soc_initdata.type == AT91_SOC_SAM9X5) { - switch (at91_soc_initdata.exid) { - case ARCH_EXID_AT91SAM9G15: - at91_soc_initdata.subtype = AT91_SOC_SAM9G15; - break; - case ARCH_EXID_AT91SAM9G35: - at91_soc_initdata.subtype = AT91_SOC_SAM9G35; - break; - case ARCH_EXID_AT91SAM9X35: - at91_soc_initdata.subtype = AT91_SOC_SAM9X35; - break; - case ARCH_EXID_AT91SAM9G25: - at91_soc_initdata.subtype = AT91_SOC_SAM9G25; - break; - case ARCH_EXID_AT91SAM9X25: - at91_soc_initdata.subtype = AT91_SOC_SAM9X25; - break; - } - } - - if (at91_soc_initdata.type == AT91_SOC_SAMA5D3) { - switch (at91_soc_initdata.exid) { - case ARCH_EXID_SAMA5D31: - at91_soc_initdata.subtype = AT91_SOC_SAMA5D31; - break; - case ARCH_EXID_SAMA5D33: - at91_soc_initdata.subtype = AT91_SOC_SAMA5D33; - break; - case ARCH_EXID_SAMA5D34: - at91_soc_initdata.subtype = AT91_SOC_SAMA5D34; - break; - case ARCH_EXID_SAMA5D35: - at91_soc_initdata.subtype = AT91_SOC_SAMA5D35; - break; - case ARCH_EXID_SAMA5D36: - at91_soc_initdata.subtype = AT91_SOC_SAMA5D36; - break; - } - } -} - -static void __init alt_soc_detect(u32 dbgu_base) -{ - u32 cidr, socid; - - /* SoC ID */ - cidr = __raw_readl(AT91_ALT_IO_P2V(dbgu_base) + AT91_DBGU_CIDR); - socid = cidr & ~AT91_CIDR_VERSION; - - switch (socid) { - case ARCH_ID_SAMA5: - at91_soc_initdata.exid = __raw_readl(AT91_ALT_IO_P2V(dbgu_base) + AT91_DBGU_EXID); - if (at91_soc_initdata.exid & ARCH_EXID_SAMA5D3) { - at91_soc_initdata.type = AT91_SOC_SAMA5D3; - } else if (at91_soc_initdata.exid & ARCH_EXID_SAMA5D4) { - at91_soc_initdata.type = AT91_SOC_SAMA5D4; - } - break; - } - - if (!at91_soc_is_detected()) - return; - - at91_soc_initdata.cidr = cidr; - - /* sub version of soc */ - if (!at91_soc_initdata.exid) - at91_soc_initdata.exid = __raw_readl(AT91_ALT_IO_P2V(dbgu_base) + AT91_DBGU_EXID); - - if (at91_soc_initdata.type == AT91_SOC_SAMA5D4) { - switch (at91_soc_initdata.exid) { - case ARCH_EXID_SAMA5D41: - at91_soc_initdata.subtype = AT91_SOC_SAMA5D41; - break; - case ARCH_EXID_SAMA5D42: - at91_soc_initdata.subtype = AT91_SOC_SAMA5D42; - break; - case ARCH_EXID_SAMA5D43: - at91_soc_initdata.subtype = AT91_SOC_SAMA5D43; - break; - case ARCH_EXID_SAMA5D44: - at91_soc_initdata.subtype = AT91_SOC_SAMA5D44; - break; - } - } -} - -static const char *soc_name[] = { - [AT91_SOC_RM9200] = "at91rm9200", - [AT91_SOC_SAM9260] = "at91sam9260", - [AT91_SOC_SAM9261] = "at91sam9261", - [AT91_SOC_SAM9263] = "at91sam9263", - [AT91_SOC_SAM9G10] = "at91sam9g10", - [AT91_SOC_SAM9G20] = "at91sam9g20", - [AT91_SOC_SAM9G45] = "at91sam9g45", - [AT91_SOC_SAM9RL] = "at91sam9rl", - [AT91_SOC_SAM9X5] = "at91sam9x5", - [AT91_SOC_SAM9N12] = "at91sam9n12", - [AT91_SOC_SAMA5D3] = "sama5d3", - [AT91_SOC_SAMA5D4] = "sama5d4", - [AT91_SOC_UNKNOWN] = "Unknown", -}; - -const char *at91_get_soc_type(struct at91_socinfo *c) -{ - return soc_name[c->type]; -} -EXPORT_SYMBOL(at91_get_soc_type); - -static const char *soc_subtype_name[] = { - [AT91_SOC_RM9200_BGA] = "at91rm9200 BGA", - [AT91_SOC_RM9200_PQFP] = "at91rm9200 PQFP", - [AT91_SOC_SAM9XE] = "at91sam9xe", - [AT91_SOC_SAM9G45ES] = "at91sam9g45es", - [AT91_SOC_SAM9M10] = "at91sam9m10", - [AT91_SOC_SAM9G46] = "at91sam9g46", - [AT91_SOC_SAM9M11] = "at91sam9m11", - [AT91_SOC_SAM9G15] = "at91sam9g15", - [AT91_SOC_SAM9G35] = "at91sam9g35", - [AT91_SOC_SAM9X35] = "at91sam9x35", - [AT91_SOC_SAM9G25] = "at91sam9g25", - [AT91_SOC_SAM9X25] = "at91sam9x25", - [AT91_SOC_SAMA5D31] = "sama5d31", - [AT91_SOC_SAMA5D33] = "sama5d33", - [AT91_SOC_SAMA5D34] = "sama5d34", - [AT91_SOC_SAMA5D35] = "sama5d35", - [AT91_SOC_SAMA5D36] = "sama5d36", - [AT91_SOC_SAMA5D41] = "sama5d41", - [AT91_SOC_SAMA5D42] = "sama5d42", - [AT91_SOC_SAMA5D43] = "sama5d43", - [AT91_SOC_SAMA5D44] = "sama5d44", - [AT91_SOC_SUBTYPE_NONE] = "None", - [AT91_SOC_SUBTYPE_UNKNOWN] = "Unknown", -}; - -const char *at91_get_soc_subtype(struct at91_socinfo *c) -{ - return soc_subtype_name[c->subtype]; -} -EXPORT_SYMBOL(at91_get_soc_subtype); - -void __init at91_map_io(void) -{ - /* Map peripherals */ - iotable_init(&at91_io_desc, 1); - - at91_soc_initdata.type = AT91_SOC_UNKNOWN; - at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_UNKNOWN; - - soc_detect(AT91_BASE_DBGU0); - if (!at91_soc_is_detected()) - soc_detect(AT91_BASE_DBGU1); - - if (!at91_soc_is_detected()) - panic(pr_fmt("Impossible to detect the SOC type")); - - pr_info("Detected soc type: %s\n", - at91_get_soc_type(&at91_soc_initdata)); - if (at91_soc_initdata.subtype != AT91_SOC_SUBTYPE_NONE) - pr_info("Detected soc subtype: %s\n", - at91_get_soc_subtype(&at91_soc_initdata)); -} - -void __init at91_alt_map_io(void) -{ - /* Map peripherals */ - iotable_init(&at91_alt_io_desc, 1); - - at91_soc_initdata.type = AT91_SOC_UNKNOWN; - at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_UNKNOWN; - - alt_soc_detect(AT91_BASE_DBGU2); - if (!at91_soc_is_detected()) - panic("AT91: Impossible to detect the SOC type"); - - pr_info("AT91: Detected soc type: %s\n", - at91_get_soc_type(&at91_soc_initdata)); - if (at91_soc_initdata.subtype != AT91_SOC_SUBTYPE_NONE) - pr_info("AT91: Detected soc subtype: %s\n", - at91_get_soc_subtype(&at91_soc_initdata)); -} - -void __iomem *at91_matrix_base; -EXPORT_SYMBOL_GPL(at91_matrix_base); - -void __init at91_ioremap_matrix(u32 base_addr) -{ - at91_matrix_base = ioremap(base_addr, 512); - if (!at91_matrix_base) - panic(pr_fmt("Impossible to ioremap at91_matrix_base\n")); -} diff --git a/arch/arm/mach-at91/soc.c b/arch/arm/mach-at91/soc.c new file mode 100644 index 000000000000..54343ffa3e53 --- /dev/null +++ b/arch/arm/mach-at91/soc.c @@ -0,0 +1,97 @@ +/* + * Copyright (C) 2015 Atmel + * + * Alexandre Belloni +#include +#include +#include +#include +#include + +#include "soc.h" + +#define AT91_DBGU_CIDR 0x40 +#define AT91_DBGU_CIDR_VERSION(x) ((x) & 0x1f) +#define AT91_DBGU_CIDR_EXT BIT(31) +#define AT91_DBGU_CIDR_MATCH_MASK 0x7fffffe0 +#define AT91_DBGU_EXID 0x44 + +struct soc_device * __init at91_soc_init(const struct at91_soc *socs) +{ + struct soc_device_attribute *soc_dev_attr; + const struct at91_soc *soc; + struct soc_device *soc_dev; + struct device_node *np; + void __iomem *regs; + u32 cidr, exid; + + np = of_find_compatible_node(NULL, NULL, "atmel,at91rm9200-dbgu"); + if (!np) + np = of_find_compatible_node(NULL, NULL, + "atmel,at91sam9260-dbgu"); + + if (!np) { + pr_warn("Could not find DBGU node"); + return NULL; + } + + regs = of_iomap(np, 0); + of_node_put(np); + + if (!regs) { + pr_warn("Could not map DBGU iomem range"); + return NULL; + } + + cidr = readl(regs + AT91_DBGU_CIDR); + exid = readl(regs + AT91_DBGU_EXID); + + iounmap(regs); + + for (soc = socs; soc->name; soc++) { + if (soc->cidr_match != (cidr & AT91_DBGU_CIDR_MATCH_MASK)) + continue; + + if (!(cidr & AT91_DBGU_CIDR_EXT) || soc->exid_match == exid) + break; + } + + if (!soc->name) { + pr_warn("Could not find matching SoC description\n"); + return NULL; + } + + soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL); + if (!soc_dev_attr) + return NULL; + + soc_dev_attr->family = soc->family; + soc_dev_attr->soc_id = soc->name; + soc_dev_attr->revision = kasprintf(GFP_KERNEL, "%X", + AT91_DBGU_CIDR_VERSION(cidr)); + soc_dev = soc_device_register(soc_dev_attr); + if (IS_ERR(soc_dev)) { + kfree(soc_dev_attr->revision); + kfree(soc_dev_attr); + pr_warn("Could not register SoC device\n"); + return NULL; + } + + if (soc->family) + pr_info("Detected SoC family: %s\n", soc->family); + pr_info("Detected SoC: %s, revision %X\n", soc->name, + AT91_DBGU_CIDR_VERSION(cidr)); + + return soc_dev; +} diff --git a/arch/arm/mach-at91/soc.h b/arch/arm/mach-at91/soc.h new file mode 100644 index 000000000000..be23c400596b --- /dev/null +++ b/arch/arm/mach-at91/soc.h @@ -0,0 +1,78 @@ +/* + * Copyright (C) 2015 Atmel + * + * Boris Brezillon + +struct at91_soc { + u32 cidr_match; + u32 exid_match; + const char *name; + const char *family; +}; + +#define AT91_SOC(__cidr, __exid, __name, __family) \ + { \ + .cidr_match = (__cidr), \ + .exid_match = (__exid), \ + .name = (__name), \ + .family = (__family), \ + } + +struct soc_device * __init +at91_soc_init(const struct at91_soc *socs); + +#define AT91RM9200_CIDR_MATCH 0x09290780 + +#define AT91SAM9260_CIDR_MATCH 0x019803a0 +#define AT91SAM9261_CIDR_MATCH 0x019703a0 +#define AT91SAM9263_CIDR_MATCH 0x019607a0 +#define AT91SAM9G20_CIDR_MATCH 0x019905a0 +#define AT91SAM9RL64_CIDR_MATCH 0x019b03a0 +#define AT91SAM9G45_CIDR_MATCH 0x019b05a0 +#define AT91SAM9X5_CIDR_MATCH 0x019a05a0 +#define AT91SAM9N12_CIDR_MATCH 0x019a07a0 + +#define AT91SAM9M11_EXID_MATCH 0x00000001 +#define AT91SAM9M10_EXID_MATCH 0x00000002 +#define AT91SAM9G46_EXID_MATCH 0x00000003 +#define AT91SAM9G45_EXID_MATCH 0x00000004 + +#define AT91SAM9G15_EXID_MATCH 0x00000000 +#define AT91SAM9G35_EXID_MATCH 0x00000001 +#define AT91SAM9X35_EXID_MATCH 0x00000002 +#define AT91SAM9G25_EXID_MATCH 0x00000003 +#define AT91SAM9X25_EXID_MATCH 0x00000004 + +#define AT91SAM9CN12_EXID_MATCH 0x00000005 +#define AT91SAM9N12_EXID_MATCH 0x00000006 +#define AT91SAM9CN11_EXID_MATCH 0x00000009 + +#define AT91SAM9XE128_CIDR_MATCH 0x329973a0 +#define AT91SAM9XE256_CIDR_MATCH 0x329a93a0 +#define AT91SAM9XE512_CIDR_MATCH 0x329aa3a0 + +#define SAMA5D3_CIDR_MATCH 0x0a5c07c0 +#define SAMA5D31_EXID_MATCH 0x00444300 +#define SAMA5D33_EXID_MATCH 0x00414300 +#define SAMA5D34_EXID_MATCH 0x00414301 +#define SAMA5D35_EXID_MATCH 0x00584300 +#define SAMA5D36_EXID_MATCH 0x00004301 + +#define SAMA5D4_CIDR_MATCH 0x0a5c07c0 +#define SAMA5D41_EXID_MATCH 0x00000001 +#define SAMA5D42_EXID_MATCH 0x00000002 +#define SAMA5D43_EXID_MATCH 0x00000003 +#define SAMA5D44_EXID_MATCH 0x00000004 + +#endif /* __AT91_SOC_H */ diff --git a/arch/arm/mach-bcm/bcm_cygnus.c b/arch/arm/mach-bcm/bcm_cygnus.c index 30dc58be51b8..7ae894c7849b 100644 --- a/arch/arm/mach-bcm/bcm_cygnus.c +++ b/arch/arm/mach-bcm/bcm_cygnus.c @@ -13,7 +13,7 @@ #include -static const char const *bcm_cygnus_dt_compat[] = { +static const char * const bcm_cygnus_dt_compat[] __initconst = { "brcm,cygnus", NULL, }; diff --git a/arch/arm/mach-cns3xxx/pm.c b/arch/arm/mach-cns3xxx/pm.c index fb38c726e987..f46b78dd6136 100644 --- a/arch/arm/mach-cns3xxx/pm.c +++ b/arch/arm/mach-cns3xxx/pm.c @@ -73,7 +73,6 @@ static void cns3xxx_pwr_soft_rst_force(unsigned int block) __raw_writel(reg, PM_SOFT_RST_REG); } -EXPORT_SYMBOL(cns3xxx_pwr_soft_rst_force); void cns3xxx_pwr_soft_rst(unsigned int block) { diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig index cd30f6f5f2ff..dd8f5312b2c0 100644 --- a/arch/arm/mach-davinci/Kconfig +++ b/arch/arm/mach-davinci/Kconfig @@ -200,17 +200,6 @@ config DA850_UI_SD_VIDEO_PORT endchoice -config DA850_WL12XX - bool "AM18x wl1271 daughter board" - depends on MACH_DAVINCI_DA850_EVM - help - The wl1271 daughter card for AM18x EVMs is a combo wireless - connectivity add-on card, based on the LS Research TiWi module with - Texas Instruments' wl1271 solution. - Say Y if you want to use a wl1271 expansion card connected to the - AM18x EVM. - - config MACH_MITYOMAPL138 bool "Critical Link MityDSP-L138/MityARM-1808 SoM" depends on ARCH_DAVINCI_DA850 diff --git a/arch/arm/mach-davinci/asp.h b/arch/arm/mach-davinci/asp.h index d9b2acd12393..1128e1d8e4b4 100644 --- a/arch/arm/mach-davinci/asp.h +++ b/arch/arm/mach-davinci/asp.h @@ -21,6 +21,9 @@ /* Bases of da830 McASP1 register banks */ #define DAVINCI_DA830_MCASP1_REG_BASE 0x01D04000 +/* Bases of da830 McASP2 register banks */ +#define DAVINCI_DA830_MCASP2_REG_BASE 0x01D08000 + /* EDMA channels of dm644x and dm355 */ #define DAVINCI_DMA_ASP0_TX 2 #define DAVINCI_DMA_ASP0_RX 3 @@ -40,6 +43,10 @@ #define DAVINCI_DA830_DMA_MCASP1_AREVT 2 #define DAVINCI_DA830_DMA_MCASP1_AXEVT 3 +/* EDMA channels of da830 McASP2 */ +#define DAVINCI_DA830_DMA_MCASP2_AREVT 4 +#define DAVINCI_DA830_DMA_MCASP2_AXEVT 5 + /* Interrupts */ #define DAVINCI_ASP0_RX_INT IRQ_MBRINT #define DAVINCI_ASP0_TX_INT IRQ_MBXINT diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index 6b5a97da9fe3..1ed545cc2b83 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -38,7 +38,6 @@ #include #include #include -#include #include #include @@ -60,9 +59,6 @@ #define DA850_MMCSD_CD_PIN GPIO_TO_PIN(4, 0) #define DA850_MMCSD_WP_PIN GPIO_TO_PIN(4, 1) -#define DA850_WLAN_EN GPIO_TO_PIN(6, 9) -#define DA850_WLAN_IRQ GPIO_TO_PIN(6, 10) - #define DA850_MII_MDIO_CLKEN_PIN GPIO_TO_PIN(2, 6) static struct mtd_partition da850evm_spiflash_part[] = { @@ -1343,109 +1339,6 @@ static __init void da850_vpif_init(void) static __init void da850_vpif_init(void) {} #endif -#ifdef CONFIG_DA850_WL12XX - -static void wl12xx_set_power(int index, bool power_on) -{ - static bool power_state; - - pr_debug("Powering %s wl12xx", power_on ? "on" : "off"); - - if (power_on == power_state) - return; - power_state = power_on; - - if (power_on) { - /* Power up sequence required for wl127x devices */ - gpio_set_value(DA850_WLAN_EN, 1); - usleep_range(15000, 15000); - gpio_set_value(DA850_WLAN_EN, 0); - usleep_range(1000, 1000); - gpio_set_value(DA850_WLAN_EN, 1); - msleep(70); - } else { - gpio_set_value(DA850_WLAN_EN, 0); - } -} - -static struct davinci_mmc_config da850_wl12xx_mmc_config = { - .set_power = wl12xx_set_power, - .wires = 4, - .max_freq = 25000000, - .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_NONREMOVABLE | - MMC_CAP_POWER_OFF_CARD, -}; - -static const short da850_wl12xx_pins[] __initconst = { - DA850_MMCSD1_DAT_0, DA850_MMCSD1_DAT_1, DA850_MMCSD1_DAT_2, - DA850_MMCSD1_DAT_3, DA850_MMCSD1_CLK, DA850_MMCSD1_CMD, - DA850_GPIO6_9, DA850_GPIO6_10, - -1 -}; - -static struct wl12xx_platform_data da850_wl12xx_wlan_data __initdata = { - .irq = -1, - .board_ref_clock = WL12XX_REFCLOCK_38, - .platform_quirks = WL12XX_PLATFORM_QUIRK_EDGE_IRQ, -}; - -static __init int da850_wl12xx_init(void) -{ - int ret; - - ret = davinci_cfg_reg_list(da850_wl12xx_pins); - if (ret) { - pr_err("wl12xx/mmc mux setup failed: %d\n", ret); - goto exit; - } - - ret = da850_register_mmcsd1(&da850_wl12xx_mmc_config); - if (ret) { - pr_err("wl12xx/mmc registration failed: %d\n", ret); - goto exit; - } - - ret = gpio_request_one(DA850_WLAN_EN, GPIOF_OUT_INIT_LOW, "wl12xx_en"); - if (ret) { - pr_err("Could not request wl12xx enable gpio: %d\n", ret); - goto exit; - } - - ret = gpio_request_one(DA850_WLAN_IRQ, GPIOF_IN, "wl12xx_irq"); - if (ret) { - pr_err("Could not request wl12xx irq gpio: %d\n", ret); - goto free_wlan_en; - } - - da850_wl12xx_wlan_data.irq = gpio_to_irq(DA850_WLAN_IRQ); - - ret = wl12xx_set_platform_data(&da850_wl12xx_wlan_data); - if (ret) { - pr_err("Could not set wl12xx data: %d\n", ret); - goto free_wlan_irq; - } - - return 0; - -free_wlan_irq: - gpio_free(DA850_WLAN_IRQ); - -free_wlan_en: - gpio_free(DA850_WLAN_EN); - -exit: - return ret; -} - -#else /* CONFIG_DA850_WL12XX */ - -static __init int da850_wl12xx_init(void) -{ - return 0; -} - -#endif /* CONFIG_DA850_WL12XX */ - #define DA850EVM_SATA_REFCLKPN_RATE (100 * 1000 * 1000) static __init void da850_evm_init(void) @@ -1502,11 +1395,6 @@ static __init void da850_evm_init(void) if (ret) pr_warn("%s: MMCSD0 registration failed: %d\n", __func__, ret); - - ret = da850_wl12xx_init(); - if (ret) - pr_warn("%s: WL12xx initialization failed: %d\n", - __func__, ret); } davinci_serial_init(da8xx_serial_device); diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c index b85b781b05fd..ddfdd820e6f2 100644 --- a/arch/arm/mach-davinci/devices-da8xx.c +++ b/arch/arm/mach-davinci/devices-da8xx.c @@ -463,16 +463,23 @@ static struct resource da830_mcasp1_resources[] = { }, /* TX event */ { + .name = "tx", .start = DAVINCI_DA830_DMA_MCASP1_AXEVT, .end = DAVINCI_DA830_DMA_MCASP1_AXEVT, .flags = IORESOURCE_DMA, }, /* RX event */ { + .name = "rx", .start = DAVINCI_DA830_DMA_MCASP1_AREVT, .end = DAVINCI_DA830_DMA_MCASP1_AREVT, .flags = IORESOURCE_DMA, }, + { + .name = "common", + .start = IRQ_DA8XX_MCASPINT, + .flags = IORESOURCE_IRQ, + }, }; static struct platform_device da830_mcasp1_device = { @@ -482,6 +489,41 @@ static struct platform_device da830_mcasp1_device = { .resource = da830_mcasp1_resources, }; +static struct resource da830_mcasp2_resources[] = { + { + .name = "mpu", + .start = DAVINCI_DA830_MCASP2_REG_BASE, + .end = DAVINCI_DA830_MCASP2_REG_BASE + (SZ_1K * 12) - 1, + .flags = IORESOURCE_MEM, + }, + /* TX event */ + { + .name = "tx", + .start = DAVINCI_DA830_DMA_MCASP2_AXEVT, + .end = DAVINCI_DA830_DMA_MCASP2_AXEVT, + .flags = IORESOURCE_DMA, + }, + /* RX event */ + { + .name = "rx", + .start = DAVINCI_DA830_DMA_MCASP2_AREVT, + .end = DAVINCI_DA830_DMA_MCASP2_AREVT, + .flags = IORESOURCE_DMA, + }, + { + .name = "common", + .start = IRQ_DA8XX_MCASPINT, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device da830_mcasp2_device = { + .name = "davinci-mcasp", + .id = 2, + .num_resources = ARRAY_SIZE(da830_mcasp2_resources), + .resource = da830_mcasp2_resources, +}; + static struct resource da850_mcasp_resources[] = { { .name = "mpu", @@ -491,16 +533,23 @@ static struct resource da850_mcasp_resources[] = { }, /* TX event */ { + .name = "tx", .start = DAVINCI_DA8XX_DMA_MCASP0_AXEVT, .end = DAVINCI_DA8XX_DMA_MCASP0_AXEVT, .flags = IORESOURCE_DMA, }, /* RX event */ { + .name = "rx", .start = DAVINCI_DA8XX_DMA_MCASP0_AREVT, .end = DAVINCI_DA8XX_DMA_MCASP0_AREVT, .flags = IORESOURCE_DMA, }, + { + .name = "common", + .start = IRQ_DA8XX_MCASPINT, + .flags = IORESOURCE_IRQ, + }, }; static struct platform_device da850_mcasp_device = { @@ -512,14 +561,31 @@ static struct platform_device da850_mcasp_device = { void __init da8xx_register_mcasp(int id, struct snd_platform_data *pdata) { - /* DA830/OMAP-L137 has 3 instances of McASP */ - if (cpu_is_davinci_da830() && id == 1) { - da830_mcasp1_device.dev.platform_data = pdata; - platform_device_register(&da830_mcasp1_device); - } else if (cpu_is_davinci_da850()) { - da850_mcasp_device.dev.platform_data = pdata; - platform_device_register(&da850_mcasp_device); + struct platform_device *pdev; + + switch (id) { + case 0: + /* Valid for DA830/OMAP-L137 or DA850/OMAP-L138 */ + pdev = &da850_mcasp_device; + break; + case 1: + /* Valid for DA830/OMAP-L137 only */ + if (!cpu_is_davinci_da830()) + return; + pdev = &da830_mcasp1_device; + break; + case 2: + /* Valid for DA830/OMAP-L137 only */ + if (!cpu_is_davinci_da830()) + return; + pdev = &da830_mcasp2_device; + break; + default: + return; } + + pdev->dev.platform_data = pdata; + platform_device_register(pdev); } static struct resource da8xx_pruss_resources[] = { diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c index 6c3bbea7d77d..3f842bb266d6 100644 --- a/arch/arm/mach-davinci/dm646x.c +++ b/arch/arm/mach-davinci/dm646x.c @@ -493,7 +493,6 @@ static u8 dm646x_default_priorities[DAVINCI_N_AINTC_IRQ] = { [IRQ_DM646X_EMACMISCINT] = 7, [IRQ_DM646X_MCASP0TXINT] = 7, [IRQ_DM646X_MCASP0RXINT] = 7, - [IRQ_AEMIFINT] = 7, [IRQ_DM646X_RESERVED_3] = 7, [IRQ_DM646X_MCASP1TXINT] = 7, /* clockevent */ [IRQ_TINT0_TINT34] = 7, /* clocksource */ @@ -610,19 +609,31 @@ static struct resource dm646x_mcasp0_resources[] = { .end = DAVINCI_DM646X_MCASP0_REG_BASE + (SZ_1K << 1) - 1, .flags = IORESOURCE_MEM, }, - /* first TX, then RX */ { + .name = "tx", .start = DAVINCI_DM646X_DMA_MCASP0_AXEVT0, .end = DAVINCI_DM646X_DMA_MCASP0_AXEVT0, .flags = IORESOURCE_DMA, }, { + .name = "rx", .start = DAVINCI_DM646X_DMA_MCASP0_AREVT0, .end = DAVINCI_DM646X_DMA_MCASP0_AREVT0, .flags = IORESOURCE_DMA, }, + { + .name = "tx", + .start = IRQ_DM646X_MCASP0TXINT, + .flags = IORESOURCE_IRQ, + }, + { + .name = "rx", + .start = IRQ_DM646X_MCASP0RXINT, + .flags = IORESOURCE_IRQ, + }, }; +/* DIT mode only, rx is not supported */ static struct resource dm646x_mcasp1_resources[] = { { .name = "mpu", @@ -630,17 +641,16 @@ static struct resource dm646x_mcasp1_resources[] = { .end = DAVINCI_DM646X_MCASP1_REG_BASE + (SZ_1K << 1) - 1, .flags = IORESOURCE_MEM, }, - /* DIT mode, only TX event */ { + .name = "tx", .start = DAVINCI_DM646X_DMA_MCASP1_AXEVT1, .end = DAVINCI_DM646X_DMA_MCASP1_AXEVT1, .flags = IORESOURCE_DMA, }, - /* DIT mode, dummy entry */ { - .start = -1, - .end = -1, - .flags = IORESOURCE_DMA, + .name = "tx", + .start = IRQ_DM646X_MCASP1TXINT, + .flags = IORESOURCE_IRQ, }, }; diff --git a/arch/arm/mach-davinci/include/mach/irqs.h b/arch/arm/mach-davinci/include/mach/irqs.h index 354af71798dc..edb2ca62321a 100644 --- a/arch/arm/mach-davinci/include/mach/irqs.h +++ b/arch/arm/mach-davinci/include/mach/irqs.h @@ -129,8 +129,8 @@ #define IRQ_DM646X_EMACMISCINT 27 #define IRQ_DM646X_MCASP0TXINT 28 #define IRQ_DM646X_MCASP0RXINT 29 +#define IRQ_DM646X_MCASP1TXINT 30 #define IRQ_DM646X_RESERVED_3 31 -#define IRQ_DM646X_MCASP1TXINT 32 #define IRQ_DM646X_VLQINT 38 #define IRQ_DM646X_UARTINT2 42 #define IRQ_DM646X_SPINT0 43 diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index 603820e5aba7..81064cd61a0a 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -123,7 +123,7 @@ config SOC_EXYNOS5800 config EXYNOS5420_MCPM bool "Exynos5420 Multi-Cluster PM support" depends on MCPM && SOC_EXYNOS5420 - select ARM_CCI + select ARM_CCI400_PORT_CTRL select ARM_CPU_SUSPEND help This is needed to provide CPU and cluster power management diff --git a/arch/arm/mach-exynos/common.h b/arch/arm/mach-exynos/common.h index f70eca7ee705..5f5cd562c593 100644 --- a/arch/arm/mach-exynos/common.h +++ b/arch/arm/mach-exynos/common.h @@ -126,6 +126,12 @@ enum { void exynos_firmware_init(void); +/* CPU BOOT mode flag for Exynos3250 SoC bootloader */ +#define C2_STATE (1 << 3) + +void exynos_set_boot_flag(unsigned int cpu, unsigned int mode); +void exynos_clear_boot_flag(unsigned int cpu, unsigned int mode); + extern u32 exynos_get_eint_wake_mask(void); #ifdef CONFIG_PM_SLEEP @@ -153,6 +159,8 @@ extern void exynos_enter_aftr(void); extern struct cpuidle_exynos_data cpuidle_coupled_exynos_data; +extern void exynos_set_delayed_reset_assertion(bool enable); + extern void s5p_init_cpu(void __iomem *cpuid_addr); extern unsigned int samsung_rev(void); extern void __iomem *cpu_boot_reg_base(void); diff --git a/arch/arm/mach-exynos/exynos.c b/arch/arm/mach-exynos/exynos.c index f44c2e05c82e..5917a30eee33 100644 --- a/arch/arm/mach-exynos/exynos.c +++ b/arch/arm/mach-exynos/exynos.c @@ -166,6 +166,33 @@ static void __init exynos_init_io(void) exynos_map_io(); } +/* + * Set or clear the USE_DELAYED_RESET_ASSERTION option. Used by smp code + * and suspend. + * + * This is necessary only on Exynos4 SoCs. When system is running + * USE_DELAYED_RESET_ASSERTION should be set so the ARM CLK clock down + * feature could properly detect global idle state when secondary CPU is + * powered down. + * + * However this should not be set when such system is going into suspend. + */ +void exynos_set_delayed_reset_assertion(bool enable) +{ + if (of_machine_is_compatible("samsung,exynos4")) { + unsigned int tmp, core_id; + + for (core_id = 0; core_id < num_possible_cpus(); core_id++) { + tmp = pmu_raw_readl(EXYNOS_ARM_CORE_OPTION(core_id)); + if (enable) + tmp |= S5P_USE_DELAYED_RESET_ASSERTION; + else + tmp &= ~(S5P_USE_DELAYED_RESET_ASSERTION); + pmu_raw_writel(tmp, EXYNOS_ARM_CORE_OPTION(core_id)); + } + } +} + /* * Apparently, these SoCs are not able to wake-up from suspend using * the PMU. Too bad. Should they suddenly become capable of such a @@ -206,7 +233,7 @@ static void __init exynos_dt_machine_init(void) if (!IS_ENABLED(CONFIG_SMP)) exynos_sysram_init(); -#ifdef CONFIG_ARM_EXYNOS_CPUIDLE +#if defined(CONFIG_SMP) && defined(CONFIG_ARM_EXYNOS_CPUIDLE) if (of_machine_is_compatible("samsung,exynos4210")) exynos_cpuidle.dev.platform_data = &cpuidle_coupled_exynos_data; #endif @@ -214,6 +241,7 @@ static void __init exynos_dt_machine_init(void) of_machine_is_compatible("samsung,exynos4212") || (of_machine_is_compatible("samsung,exynos4412") && of_machine_is_compatible("samsung,trats2")) || + of_machine_is_compatible("samsung,exynos3250") || of_machine_is_compatible("samsung,exynos5250")) platform_device_register(&exynos_cpuidle); diff --git a/arch/arm/mach-exynos/firmware.c b/arch/arm/mach-exynos/firmware.c index 4791a3cc00f9..1bd35763f12e 100644 --- a/arch/arm/mach-exynos/firmware.c +++ b/arch/arm/mach-exynos/firmware.c @@ -48,7 +48,13 @@ static int exynos_do_idle(unsigned long mode) __raw_writel(virt_to_phys(exynos_cpu_resume_ns), sysram_ns_base_addr + 0x24); __raw_writel(EXYNOS_AFTR_MAGIC, sysram_ns_base_addr + 0x20); - exynos_smc(SMC_CMD_CPU0AFTR, 0, 0, 0); + if (soc_is_exynos3250()) { + exynos_smc(SMC_CMD_SAVE, OP_TYPE_CORE, + SMC_POWERSTATE_IDLE, 0); + exynos_smc(SMC_CMD_SHUTDOWN, OP_TYPE_CLUSTER, + SMC_POWERSTATE_IDLE, 0); + } else + exynos_smc(SMC_CMD_CPU0AFTR, 0, 0, 0); break; case FW_DO_IDLE_SLEEP: exynos_smc(SMC_CMD_SLEEP, 0, 0, 0); @@ -206,3 +212,28 @@ void __init exynos_firmware_init(void) outer_cache.configure = exynos_l2_configure; } } + +#define REG_CPU_STATE_ADDR (sysram_ns_base_addr + 0x28) +#define BOOT_MODE_MASK 0x1f + +void exynos_set_boot_flag(unsigned int cpu, unsigned int mode) +{ + unsigned int tmp; + + tmp = __raw_readl(REG_CPU_STATE_ADDR + cpu * 4); + + if (mode & BOOT_MODE_MASK) + tmp &= ~BOOT_MODE_MASK; + + tmp |= mode; + __raw_writel(tmp, REG_CPU_STATE_ADDR + cpu * 4); +} + +void exynos_clear_boot_flag(unsigned int cpu, unsigned int mode) +{ + unsigned int tmp; + + tmp = __raw_readl(REG_CPU_STATE_ADDR + cpu * 4); + tmp &= ~mode; + __raw_writel(tmp, REG_CPU_STATE_ADDR + cpu * 4); +} diff --git a/arch/arm/mach-exynos/mcpm-exynos.c b/arch/arm/mach-exynos/mcpm-exynos.c index b0d3c2e876fb..9bdf54795f05 100644 --- a/arch/arm/mach-exynos/mcpm-exynos.c +++ b/arch/arm/mach-exynos/mcpm-exynos.c @@ -61,25 +61,7 @@ static void __iomem *ns_sram_base_addr; : "r0", "r1", "r2", "r3", "r4", "r5", "r6", "r7", \ "r9", "r10", "lr", "memory") -/* - * We can't use regular spinlocks. In the switcher case, it is possible - * for an outbound CPU to call power_down() after its inbound counterpart - * is already live using the same logical CPU number which trips lockdep - * debugging. - */ -static arch_spinlock_t exynos_mcpm_lock = __ARCH_SPIN_LOCK_UNLOCKED; -static int -cpu_use_count[EXYNOS5420_CPUS_PER_CLUSTER][EXYNOS5420_NR_CLUSTERS]; - -#define exynos_cluster_usecnt(cluster) \ - (cpu_use_count[0][cluster] + \ - cpu_use_count[1][cluster] + \ - cpu_use_count[2][cluster] + \ - cpu_use_count[3][cluster]) - -#define exynos_cluster_unused(cluster) !exynos_cluster_usecnt(cluster) - -static int exynos_power_up(unsigned int cpu, unsigned int cluster) +static int exynos_cpu_powerup(unsigned int cpu, unsigned int cluster) { unsigned int cpunr = cpu + (cluster * EXYNOS5420_CPUS_PER_CLUSTER); @@ -88,127 +70,65 @@ static int exynos_power_up(unsigned int cpu, unsigned int cluster) cluster >= EXYNOS5420_NR_CLUSTERS) return -EINVAL; - /* - * Since this is called with IRQs enabled, and no arch_spin_lock_irq - * variant exists, we need to disable IRQs manually here. - */ - local_irq_disable(); - arch_spin_lock(&exynos_mcpm_lock); - - cpu_use_count[cpu][cluster]++; - if (cpu_use_count[cpu][cluster] == 1) { - bool was_cluster_down = - (exynos_cluster_usecnt(cluster) == 1); - - /* - * Turn on the cluster (L2/COMMON) and then power on the - * cores. - */ - if (was_cluster_down) - exynos_cluster_power_up(cluster); - - exynos_cpu_power_up(cpunr); - } else if (cpu_use_count[cpu][cluster] != 2) { - /* - * The only possible values are: - * 0 = CPU down - * 1 = CPU (still) up - * 2 = CPU requested to be up before it had a chance - * to actually make itself down. - * Any other value is a bug. - */ - BUG(); - } - - arch_spin_unlock(&exynos_mcpm_lock); - local_irq_enable(); - + exynos_cpu_power_up(cpunr); return 0; } -/* - * NOTE: This function requires the stack data to be visible through power down - * and can only be executed on processors like A15 and A7 that hit the cache - * with the C bit clear in the SCTLR register. - */ -static void exynos_power_down(void) +static int exynos_cluster_powerup(unsigned int cluster) { - unsigned int mpidr, cpu, cluster; - bool last_man = false, skip_wfi = false; - unsigned int cpunr; + pr_debug("%s: cluster %u\n", __func__, cluster); + if (cluster >= EXYNOS5420_NR_CLUSTERS) + return -EINVAL; - mpidr = read_cpuid_mpidr(); - cpu = MPIDR_AFFINITY_LEVEL(mpidr, 0); - cluster = MPIDR_AFFINITY_LEVEL(mpidr, 1); - cpunr = cpu + (cluster * EXYNOS5420_CPUS_PER_CLUSTER); + exynos_cluster_power_up(cluster); + return 0; +} + +static void exynos_cpu_powerdown_prepare(unsigned int cpu, unsigned int cluster) +{ + unsigned int cpunr = cpu + (cluster * EXYNOS5420_CPUS_PER_CLUSTER); pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster); BUG_ON(cpu >= EXYNOS5420_CPUS_PER_CLUSTER || cluster >= EXYNOS5420_NR_CLUSTERS); + exynos_cpu_power_down(cpunr); +} - __mcpm_cpu_going_down(cpu, cluster); +static void exynos_cluster_powerdown_prepare(unsigned int cluster) +{ + pr_debug("%s: cluster %u\n", __func__, cluster); + BUG_ON(cluster >= EXYNOS5420_NR_CLUSTERS); + exynos_cluster_power_down(cluster); +} - arch_spin_lock(&exynos_mcpm_lock); - BUG_ON(__mcpm_cluster_state(cluster) != CLUSTER_UP); - cpu_use_count[cpu][cluster]--; - if (cpu_use_count[cpu][cluster] == 0) { - exynos_cpu_power_down(cpunr); +static void exynos_cpu_cache_disable(void) +{ + /* Disable and flush the local CPU cache. */ + exynos_v7_exit_coherency_flush(louis); +} - if (exynos_cluster_unused(cluster)) { - exynos_cluster_power_down(cluster); - last_man = true; - } - } else if (cpu_use_count[cpu][cluster] == 1) { +static void exynos_cluster_cache_disable(void) +{ + if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A15) { /* - * A power_up request went ahead of us. - * Even if we do not want to shut this CPU down, - * the caller expects a certain state as if the WFI - * was aborted. So let's continue with cache cleaning. + * On the Cortex-A15 we need to disable + * L2 prefetching before flushing the cache. */ - skip_wfi = true; - } else { - BUG(); + asm volatile( + "mcr p15, 1, %0, c15, c0, 3\n\t" + "isb\n\t" + "dsb" + : : "r" (0x400)); } - if (last_man && __mcpm_outbound_enter_critical(cpu, cluster)) { - arch_spin_unlock(&exynos_mcpm_lock); + /* Flush all cache levels for this cluster. */ + exynos_v7_exit_coherency_flush(all); - if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A15) { - /* - * On the Cortex-A15 we need to disable - * L2 prefetching before flushing the cache. - */ - asm volatile( - "mcr p15, 1, %0, c15, c0, 3\n\t" - "isb\n\t" - "dsb" - : : "r" (0x400)); - } - - /* Flush all cache levels for this cluster. */ - exynos_v7_exit_coherency_flush(all); - - /* - * Disable cluster-level coherency by masking - * incoming snoops and DVM messages: - */ - cci_disable_port_by_cpu(mpidr); - - __mcpm_outbound_leave_critical(cluster, CLUSTER_DOWN); - } else { - arch_spin_unlock(&exynos_mcpm_lock); - - /* Disable and flush the local CPU cache. */ - exynos_v7_exit_coherency_flush(louis); - } - - __mcpm_cpu_down(cpu, cluster); - - /* Now we are prepared for power-down, do it: */ - if (!skip_wfi) - wfi(); - - /* Not dead at this point? Let our caller cope. */ + /* + * Disable cluster-level coherency by masking + * incoming snoops and DVM messages: + */ + cci_disable_port_by_cpu(read_cpuid_mpidr()); } static int exynos_wait_for_powerdown(unsigned int cpu, unsigned int cluster) @@ -222,10 +142,8 @@ static int exynos_wait_for_powerdown(unsigned int cpu, unsigned int cluster) /* Wait for the core state to be OFF */ while (tries--) { - if (ACCESS_ONCE(cpu_use_count[cpu][cluster]) == 0) { - if ((exynos_cpu_power_state(cpunr) == 0)) - return 0; /* success: the CPU is halted */ - } + if ((exynos_cpu_power_state(cpunr) == 0)) + return 0; /* success: the CPU is halted */ /* Otherwise, wait and retry: */ msleep(1); @@ -234,63 +152,23 @@ static int exynos_wait_for_powerdown(unsigned int cpu, unsigned int cluster) return -ETIMEDOUT; /* timeout */ } -static void exynos_powered_up(void) +static void exynos_cpu_is_up(unsigned int cpu, unsigned int cluster) { - unsigned int mpidr, cpu, cluster; - - mpidr = read_cpuid_mpidr(); - cpu = MPIDR_AFFINITY_LEVEL(mpidr, 0); - cluster = MPIDR_AFFINITY_LEVEL(mpidr, 1); - - arch_spin_lock(&exynos_mcpm_lock); - if (cpu_use_count[cpu][cluster] == 0) - cpu_use_count[cpu][cluster] = 1; - arch_spin_unlock(&exynos_mcpm_lock); -} - -static void exynos_suspend(u64 residency) -{ - unsigned int mpidr, cpunr; - - exynos_power_down(); - - /* - * Execution reaches here only if cpu did not power down. - * Hence roll back the changes done in exynos_power_down function. - * - * CAUTION: "This function requires the stack data to be visible through - * power down and can only be executed on processors like A15 and A7 - * that hit the cache with the C bit clear in the SCTLR register." - */ - mpidr = read_cpuid_mpidr(); - cpunr = exynos_pmu_cpunr(mpidr); - - exynos_cpu_power_up(cpunr); + /* especially when resuming: make sure power control is set */ + exynos_cpu_powerup(cpu, cluster); } static const struct mcpm_platform_ops exynos_power_ops = { - .power_up = exynos_power_up, - .power_down = exynos_power_down, + .cpu_powerup = exynos_cpu_powerup, + .cluster_powerup = exynos_cluster_powerup, + .cpu_powerdown_prepare = exynos_cpu_powerdown_prepare, + .cluster_powerdown_prepare = exynos_cluster_powerdown_prepare, + .cpu_cache_disable = exynos_cpu_cache_disable, + .cluster_cache_disable = exynos_cluster_cache_disable, .wait_for_powerdown = exynos_wait_for_powerdown, - .suspend = exynos_suspend, - .powered_up = exynos_powered_up, + .cpu_is_up = exynos_cpu_is_up, }; -static void __init exynos_mcpm_usage_count_init(void) -{ - unsigned int mpidr, cpu, cluster; - - mpidr = read_cpuid_mpidr(); - cpu = MPIDR_AFFINITY_LEVEL(mpidr, 0); - cluster = MPIDR_AFFINITY_LEVEL(mpidr, 1); - - pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster); - BUG_ON(cpu >= EXYNOS5420_CPUS_PER_CLUSTER || - cluster >= EXYNOS5420_NR_CLUSTERS); - - cpu_use_count[cpu][cluster] = 1; -} - /* * Enable cluster-level coherency, in preparation for turning on the MMU. */ @@ -302,19 +180,6 @@ static void __naked exynos_pm_power_up_setup(unsigned int affinity_level) "b cci_enable_port_for_self"); } -static void __init exynos_cache_off(void) -{ - if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A15) { - /* disable L2 prefetching on the Cortex-A15 */ - asm volatile( - "mcr p15, 1, %0, c15, c0, 3\n\t" - "isb\n\t" - "dsb" - : : "r" (0x400)); - } - exynos_v7_exit_coherency_flush(all); -} - static const struct of_device_id exynos_dt_mcpm_match[] = { { .compatible = "samsung,exynos5420" }, { .compatible = "samsung,exynos5800" }, @@ -370,13 +235,11 @@ static int __init exynos_mcpm_init(void) */ pmu_raw_writel(EXYNOS5420_SWRESET_KFC_SEL, S5P_PMU_SPARE3); - exynos_mcpm_usage_count_init(); - ret = mcpm_platform_register(&exynos_power_ops); if (!ret) ret = mcpm_sync_init(exynos_pm_power_up_setup); if (!ret) - ret = mcpm_loopback(exynos_cache_off); /* turn on the CCI */ + ret = mcpm_loopback(exynos_cluster_cache_disable); /* turn on the CCI */ if (ret) { iounmap(ns_sram_base_addr); return ret; diff --git a/arch/arm/mach-exynos/platsmp.c b/arch/arm/mach-exynos/platsmp.c index d2e9f12d12f1..a825bca2a2b6 100644 --- a/arch/arm/mach-exynos/platsmp.c +++ b/arch/arm/mach-exynos/platsmp.c @@ -34,30 +34,6 @@ extern void exynos4_secondary_startup(void); -/* - * Set or clear the USE_DELAYED_RESET_ASSERTION option, set on Exynos4 SoCs - * during hot-(un)plugging CPUx. - * - * The feature can be cleared safely during first boot of secondary CPU. - * - * Exynos4 SoCs require setting USE_DELAYED_RESET_ASSERTION during powering - * down a CPU so the CPU idle clock down feature could properly detect global - * idle state when CPUx is off. - */ -static void exynos_set_delayed_reset_assertion(u32 core_id, bool enable) -{ - if (soc_is_exynos4()) { - unsigned int tmp; - - tmp = pmu_raw_readl(EXYNOS_ARM_CORE_OPTION(core_id)); - if (enable) - tmp |= S5P_USE_DELAYED_RESET_ASSERTION; - else - tmp &= ~(S5P_USE_DELAYED_RESET_ASSERTION); - pmu_raw_writel(tmp, EXYNOS_ARM_CORE_OPTION(core_id)); - } -} - #ifdef CONFIG_HOTPLUG_CPU static inline void cpu_leave_lowpower(u32 core_id) { @@ -73,8 +49,6 @@ static inline void cpu_leave_lowpower(u32 core_id) : "=&r" (v) : "Ir" (CR_C), "Ir" (0x40) : "cc"); - - exynos_set_delayed_reset_assertion(core_id, false); } static inline void platform_do_lowpower(unsigned int cpu, int *spurious) @@ -87,14 +61,6 @@ static inline void platform_do_lowpower(unsigned int cpu, int *spurious) /* Turn the CPU off on next WFI instruction. */ exynos_cpu_power_down(core_id); - /* - * Exynos4 SoCs require setting - * USE_DELAYED_RESET_ASSERTION so the CPU idle - * clock down feature could properly detect - * global idle state when CPUx is off. - */ - exynos_set_delayed_reset_assertion(core_id, true); - wfi(); if (pen_release == core_id) { @@ -126,6 +92,8 @@ static inline void platform_do_lowpower(unsigned int cpu, int *spurious) */ void exynos_cpu_power_down(int cpu) { + u32 core_conf; + if (cpu == 0 && (soc_is_exynos5420() || soc_is_exynos5800())) { /* * Bypass power down for CPU0 during suspend. Check for @@ -137,7 +105,10 @@ void exynos_cpu_power_down(int cpu) if (!(val & S5P_CORE_LOCAL_PWR_EN)) return; } - pmu_raw_writel(0, EXYNOS_ARM_CORE_CONFIGURATION(cpu)); + + core_conf = pmu_raw_readl(EXYNOS_ARM_CORE_CONFIGURATION(cpu)); + core_conf &= ~S5P_CORE_LOCAL_PWR_EN; + pmu_raw_writel(core_conf, EXYNOS_ARM_CORE_CONFIGURATION(cpu)); } /** @@ -148,7 +119,12 @@ void exynos_cpu_power_down(int cpu) */ void exynos_cpu_power_up(int cpu) { - pmu_raw_writel(S5P_CORE_LOCAL_PWR_EN, + u32 core_conf = S5P_CORE_LOCAL_PWR_EN; + + if (soc_is_exynos3250()) + core_conf |= S5P_CORE_AUTOWAKEUP_EN; + + pmu_raw_writel(core_conf, EXYNOS_ARM_CORE_CONFIGURATION(cpu)); } @@ -226,6 +202,10 @@ static void exynos_core_restart(u32 core_id) if (!of_machine_is_compatible("samsung,exynos3250")) return; + while (!pmu_raw_readl(S5P_PMU_SPARE2)) + udelay(10); + udelay(10); + val = pmu_raw_readl(EXYNOS_ARM_CORE_STATUS(core_id)); val |= S5P_CORE_WAKEUP_FROM_LOCAL_CFG; pmu_raw_writel(val, EXYNOS_ARM_CORE_STATUS(core_id)); @@ -346,7 +326,10 @@ static int exynos_boot_secondary(unsigned int cpu, struct task_struct *idle) call_firmware_op(cpu_boot, core_id); - arch_send_wakeup_ipi_mask(cpumask_of(cpu)); + if (soc_is_exynos3250()) + dsb_sev(); + else + arch_send_wakeup_ipi_mask(cpumask_of(cpu)); if (pen_release == -1) break; @@ -354,9 +337,6 @@ static int exynos_boot_secondary(unsigned int cpu, struct task_struct *idle) udelay(10); } - /* No harm if this is called during first boot of secondary CPU */ - exynos_set_delayed_reset_assertion(core_id, false); - /* * now the secondary core is starting up let it run its * calibrations, then wait for it to finish @@ -403,6 +383,8 @@ static void __init exynos_smp_prepare_cpus(unsigned int max_cpus) exynos_sysram_init(); + exynos_set_delayed_reset_assertion(true); + if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A9) scu_enable(scu_base_addr()); diff --git a/arch/arm/mach-exynos/pm.c b/arch/arm/mach-exynos/pm.c index e6209dadc00d..cc75ab448be3 100644 --- a/arch/arm/mach-exynos/pm.c +++ b/arch/arm/mach-exynos/pm.c @@ -127,6 +127,8 @@ int exynos_pm_central_resume(void) static void exynos_set_wakeupmask(long mask) { pmu_raw_writel(mask, S5P_WAKEUP_MASK); + if (soc_is_exynos3250()) + pmu_raw_writel(0x0, S5P_WAKEUP_MASK2); } static void exynos_cpu_set_boot_vector(long flags) @@ -140,7 +142,7 @@ static int exynos_aftr_finisher(unsigned long flags) { int ret; - exynos_set_wakeupmask(0x0000ff3e); + exynos_set_wakeupmask(soc_is_exynos3250() ? 0x40003ffe : 0x0000ff3e); /* Set value of power down register for aftr mode */ exynos_sys_powerdown_conf(SYS_AFTR); @@ -157,8 +159,13 @@ static int exynos_aftr_finisher(unsigned long flags) void exynos_enter_aftr(void) { + unsigned int cpuid = smp_processor_id(); + cpu_pm_enter(); + if (soc_is_exynos3250()) + exynos_set_boot_flag(cpuid, C2_STATE); + exynos_pm_central_suspend(); if (of_machine_is_compatible("samsung,exynos4212") || @@ -178,9 +185,13 @@ void exynos_enter_aftr(void) exynos_pm_central_resume(); + if (soc_is_exynos3250()) + exynos_clear_boot_flag(cpuid, C2_STATE); + cpu_pm_exit(); } +#if defined(CONFIG_SMP) && defined(CONFIG_ARM_EXYNOS_CPUIDLE) static atomic_t cpu1_wakeup = ATOMIC_INIT(0); static int exynos_cpu0_enter_aftr(void) @@ -302,3 +313,4 @@ struct cpuidle_exynos_data cpuidle_coupled_exynos_data = { .pre_enter_aftr = exynos_pre_enter_aftr, .post_enter_aftr = exynos_post_enter_aftr, }; +#endif /* CONFIG_SMP && CONFIG_ARM_EXYNOS_CPUIDLE */ diff --git a/arch/arm/mach-exynos/pm_domains.c b/arch/arm/mach-exynos/pm_domains.c index 37266a826437..a9686535f9ed 100644 --- a/arch/arm/mach-exynos/pm_domains.c +++ b/arch/arm/mach-exynos/pm_domains.c @@ -37,6 +37,7 @@ struct exynos_pm_domain { struct clk *oscclk; struct clk *clk[MAX_CLK_PER_DOMAIN]; struct clk *pclk[MAX_CLK_PER_DOMAIN]; + struct clk *asb_clk[MAX_CLK_PER_DOMAIN]; }; static int exynos_pd_power(struct generic_pm_domain *domain, bool power_on) @@ -45,14 +46,19 @@ static int exynos_pd_power(struct generic_pm_domain *domain, bool power_on) void __iomem *base; u32 timeout, pwr; char *op; + int i; pd = container_of(domain, struct exynos_pm_domain, pd); base = pd->base; + for (i = 0; i < MAX_CLK_PER_DOMAIN; i++) { + if (IS_ERR(pd->asb_clk[i])) + break; + clk_prepare_enable(pd->asb_clk[i]); + } + /* Set oscclk before powering off a domain*/ if (!power_on) { - int i; - for (i = 0; i < MAX_CLK_PER_DOMAIN; i++) { if (IS_ERR(pd->clk[i])) break; @@ -81,8 +87,6 @@ static int exynos_pd_power(struct generic_pm_domain *domain, bool power_on) /* Restore clocks after powering on a domain*/ if (power_on) { - int i; - for (i = 0; i < MAX_CLK_PER_DOMAIN; i++) { if (IS_ERR(pd->clk[i])) break; @@ -92,6 +96,12 @@ static int exynos_pd_power(struct generic_pm_domain *domain, bool power_on) } } + for (i = 0; i < MAX_CLK_PER_DOMAIN; i++) { + if (IS_ERR(pd->asb_clk[i])) + break; + clk_disable_unprepare(pd->asb_clk[i]); + } + return 0; } @@ -125,12 +135,21 @@ static __init int exynos4_pm_init_power_domain(void) return -ENOMEM; } - pd->pd.name = kstrdup(np->name, GFP_KERNEL); + pd->pd.name = kstrdup(dev_name(dev), GFP_KERNEL); pd->name = pd->pd.name; pd->base = of_iomap(np, 0); pd->pd.power_off = exynos_pd_power_off; pd->pd.power_on = exynos_pd_power_on; + for (i = 0; i < MAX_CLK_PER_DOMAIN; i++) { + char clk_name[8]; + + snprintf(clk_name, sizeof(clk_name), "asb%d", i); + pd->asb_clk[i] = clk_get(dev, clk_name); + if (IS_ERR(pd->asb_clk[i])) + break; + } + pd->oscclk = clk_get(dev, "oscclk"); if (IS_ERR(pd->oscclk)) goto no_clk; @@ -169,7 +188,7 @@ no_clk: args.np = np; args.args_count = 0; child_domain = of_genpd_get_from_provider(&args); - if (!child_domain) + if (IS_ERR(child_domain)) continue; if (of_parse_phandle_with_args(np, "power-domains", @@ -177,7 +196,7 @@ no_clk: continue; parent_domain = of_genpd_get_from_provider(&args); - if (!parent_domain) + if (IS_ERR(parent_domain)) continue; if (pm_genpd_add_subdomain(parent_domain, child_domain)) diff --git a/arch/arm/mach-exynos/regs-pmu.h b/arch/arm/mach-exynos/regs-pmu.h index eb461e1c325a..b7614333d296 100644 --- a/arch/arm/mach-exynos/regs-pmu.h +++ b/arch/arm/mach-exynos/regs-pmu.h @@ -43,12 +43,14 @@ #define S5P_WAKEUP_STAT 0x0600 #define S5P_EINT_WAKEUP_MASK 0x0604 #define S5P_WAKEUP_MASK 0x0608 +#define S5P_WAKEUP_MASK2 0x0614 #define S5P_INFORM0 0x0800 #define S5P_INFORM1 0x0804 #define S5P_INFORM5 0x0814 #define S5P_INFORM6 0x0818 #define S5P_INFORM7 0x081C +#define S5P_PMU_SPARE2 0x0908 #define S5P_PMU_SPARE3 0x090C #define EXYNOS_IROM_DATA2 0x0988 @@ -182,6 +184,7 @@ #define S5P_CORE_LOCAL_PWR_EN 0x3 #define S5P_CORE_WAKEUP_FROM_LOCAL_CFG (0x3 << 8) +#define S5P_CORE_AUTOWAKEUP_EN (1 << 31) /* Only for EXYNOS4210 */ #define S5P_CMU_CLKSTOP_LCD1_LOWPWR 0x1154 diff --git a/arch/arm/mach-exynos/smc.h b/arch/arm/mach-exynos/smc.h index f7b82f9c1e21..c2845717bc8f 100644 --- a/arch/arm/mach-exynos/smc.h +++ b/arch/arm/mach-exynos/smc.h @@ -17,6 +17,8 @@ #define SMC_CMD_SLEEP (-3) #define SMC_CMD_CPU1BOOT (-4) #define SMC_CMD_CPU0AFTR (-5) +#define SMC_CMD_SAVE (-6) +#define SMC_CMD_SHUTDOWN (-7) /* For CP15 Access */ #define SMC_CMD_C15RESUME (-11) /* For L2 Cache Access */ @@ -32,4 +34,11 @@ extern void exynos_smc(u32 cmd, u32 arg1, u32 arg2, u32 arg3); #endif /* __ASSEMBLY__ */ +/* op type for SMC_CMD_SAVE and SMC_CMD_SHUTDOWN */ +#define OP_TYPE_CORE 0x0 +#define OP_TYPE_CLUSTER 0x1 + +/* Power State required for SMC_CMD_SAVE and SMC_CMD_SHUTDOWN */ +#define SMC_POWERSTATE_IDLE 0x1 + #endif diff --git a/arch/arm/mach-exynos/suspend.c b/arch/arm/mach-exynos/suspend.c index 2146d918aedd..c0b6dccbf7bd 100644 --- a/arch/arm/mach-exynos/suspend.c +++ b/arch/arm/mach-exynos/suspend.c @@ -65,8 +65,6 @@ static struct sleep_save exynos_core_save[] = { struct exynos_pm_data { const struct exynos_wkup_irq *wkup_irq; - struct sleep_save *extra_save; - int num_extra_save; unsigned int wake_disable_mask; unsigned int *release_ret_regs; @@ -77,7 +75,7 @@ struct exynos_pm_data { int (*cpu_suspend)(unsigned long); }; -struct exynos_pm_data *pm_data; +static const struct exynos_pm_data *pm_data; static int exynos5420_cpu_state; static unsigned int exynos_pmu_spare3; @@ -106,7 +104,7 @@ static const struct exynos_wkup_irq exynos5250_wkup_irq[] = { { /* sentinel */ }, }; -unsigned int exynos_release_ret_regs[] = { +static unsigned int exynos_release_ret_regs[] = { S5P_PAD_RET_MAUDIO_OPTION, S5P_PAD_RET_GPIO_OPTION, S5P_PAD_RET_UART_OPTION, @@ -117,7 +115,7 @@ unsigned int exynos_release_ret_regs[] = { REG_TABLE_END, }; -unsigned int exynos3250_release_ret_regs[] = { +static unsigned int exynos3250_release_ret_regs[] = { S5P_PAD_RET_MAUDIO_OPTION, S5P_PAD_RET_GPIO_OPTION, S5P_PAD_RET_UART_OPTION, @@ -130,7 +128,7 @@ unsigned int exynos3250_release_ret_regs[] = { REG_TABLE_END, }; -unsigned int exynos5420_release_ret_regs[] = { +static unsigned int exynos5420_release_ret_regs[] = { EXYNOS_PAD_RET_DRAM_OPTION, EXYNOS_PAD_RET_MAUDIO_OPTION, EXYNOS_PAD_RET_JTAG_OPTION, @@ -344,15 +342,13 @@ static void exynos_pm_enter_sleep_mode(void) static void exynos_pm_prepare(void) { + exynos_set_delayed_reset_assertion(false); + /* Set wake-up mask registers */ exynos_pm_set_wakeup_mask(); s3c_pm_do_save(exynos_core_save, ARRAY_SIZE(exynos_core_save)); - if (pm_data->extra_save) - s3c_pm_do_save(pm_data->extra_save, - pm_data->num_extra_save); - exynos_pm_enter_sleep_mode(); /* ensure at least INFORM0 has the resume address */ @@ -475,10 +471,6 @@ static void exynos_pm_resume(void) /* For release retention */ exynos_pm_release_retention(); - if (pm_data->extra_save) - s3c_pm_do_restore_core(pm_data->extra_save, - pm_data->num_extra_save); - s3c_pm_do_restore_core(exynos_core_save, ARRAY_SIZE(exynos_core_save)); if (cpuid == ARM_CPU_PART_CORTEX_A9) @@ -492,6 +484,7 @@ early_wakeup: /* Clear SLEEP mode set in INFORM1 */ pmu_raw_writel(0x0, S5P_INFORM1); + exynos_set_delayed_reset_assertion(true); } static void exynos3250_pm_resume(void) @@ -685,7 +678,7 @@ static const struct exynos_pm_data exynos5250_pm_data = { .cpu_suspend = exynos_cpu_suspend, }; -static struct exynos_pm_data exynos5420_pm_data = { +static const struct exynos_pm_data exynos5420_pm_data = { .wkup_irq = exynos5250_wkup_irq, .wake_disable_mask = (0x7F << 7) | (0x1F << 1), .release_ret_regs = exynos5420_release_ret_regs, @@ -733,10 +726,12 @@ void __init exynos_pm_init(void) return; } - if (WARN_ON(!of_find_property(np, "interrupt-controller", NULL))) + if (WARN_ON(!of_find_property(np, "interrupt-controller", NULL))) { pr_warn("Outdated DT detected, suspend/resume will NOT work\n"); + return; + } - pm_data = (struct exynos_pm_data *) match->data; + pm_data = (const struct exynos_pm_data *) match->data; /* All wakeup disable */ tmp = pmu_raw_readl(S5P_WAKEUP_MASK); diff --git a/arch/arm/mach-gemini/common.h b/arch/arm/mach-gemini/common.h index 38a45260a7c8..dd883698ff7e 100644 --- a/arch/arm/mach-gemini/common.h +++ b/arch/arm/mach-gemini/common.h @@ -12,6 +12,8 @@ #ifndef __GEMINI_COMMON_H__ #define __GEMINI_COMMON_H__ +#include + struct mtd_partition; extern void gemini_map_io(void); @@ -26,6 +28,6 @@ extern int platform_register_pflash(unsigned int size, struct mtd_partition *parts, unsigned int nr_parts); -extern void gemini_restart(char mode, const char *cmd); +extern void gemini_restart(enum reboot_mode mode, const char *cmd); #endif /* __GEMINI_COMMON_H__ */ diff --git a/arch/arm/mach-gemini/reset.c b/arch/arm/mach-gemini/reset.c index b26659759e27..21a6d6d4f9c4 100644 --- a/arch/arm/mach-gemini/reset.c +++ b/arch/arm/mach-gemini/reset.c @@ -14,7 +14,9 @@ #include #include -void gemini_restart(char mode, const char *cmd) +#include "common.h" + +void gemini_restart(enum reboot_mode mode, const char *cmd) { __raw_writel(RESET_GLOBAL | RESET_CPU1, IO_ADDRESS(GEMINI_GLOBAL_BASE) + GLOBAL_RESET); diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index c8dffcee9736..3a3d3e9d7bfd 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -21,6 +21,7 @@ config MXC_AVIC config MXC_DEBUG_BOARD bool "Enable MXC debug board(for 3-stack)" + depends on MACH_MX27_3DS || MACH_MX31_3DS || MACH_MX35_3DS help The debug board is an integral part of the MXC 3-stack(PDK) platforms, it can be attached or removed from the peripheral @@ -50,6 +51,7 @@ config HAVE_IMX_ANATOP config HAVE_IMX_GPC bool + select PM_GENERIC_DOMAINS if PM config HAVE_IMX_MMDC bool @@ -77,13 +79,6 @@ config SOC_IMX21 select IMX_HAVE_IOMUX_V1 select MXC_AVIC -config SOC_IMX25 - bool - select ARCH_MXC_IOMUX_V3 - select CPU_ARM926T - select MXC_AVIC - select PINCTRL_IMX25 - config SOC_IMX27 bool select CPU_ARM926T @@ -149,62 +144,6 @@ config MACH_MX21ADS Include support for MX21ADS platform. This includes specific configurations for the board and its peripherals. -comment "MX25 platforms:" - -config MACH_MX25_3DS - bool "Support MX25PDK (3DS) Platform" - select IMX_HAVE_PLATFORM_FLEXCAN - select IMX_HAVE_PLATFORM_FSL_USB2_UDC - select IMX_HAVE_PLATFORM_IMX2_WDT - select IMX_HAVE_PLATFORM_IMXDI_RTC - select IMX_HAVE_PLATFORM_IMX_FB - select IMX_HAVE_PLATFORM_IMX_I2C - select IMX_HAVE_PLATFORM_IMX_KEYPAD - select IMX_HAVE_PLATFORM_IMX_UART - select IMX_HAVE_PLATFORM_MXC_EHCI - select IMX_HAVE_PLATFORM_MXC_NAND - select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX - select SOC_IMX25 - -config MACH_EUKREA_CPUIMX25SD - bool "Support Eukrea CPUIMX25 Platform" - select IMX_HAVE_PLATFORM_FLEXCAN - select IMX_HAVE_PLATFORM_FSL_USB2_UDC - select IMX_HAVE_PLATFORM_IMX2_WDT - select IMX_HAVE_PLATFORM_IMXDI_RTC - select IMX_HAVE_PLATFORM_IMX_FB - select IMX_HAVE_PLATFORM_IMX_I2C - select IMX_HAVE_PLATFORM_IMX_UART - select IMX_HAVE_PLATFORM_MXC_EHCI - select IMX_HAVE_PLATFORM_MXC_NAND - select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX - select USB_ULPI_VIEWPORT if USB_ULPI - select SOC_IMX25 - -choice - prompt "Baseboard" - depends on MACH_EUKREA_CPUIMX25SD - default MACH_EUKREA_MBIMXSD25_BASEBOARD - -config MACH_EUKREA_MBIMXSD25_BASEBOARD - bool "Eukrea MBIMXSD development board" - select IMX_HAVE_PLATFORM_GPIO_KEYS - select IMX_HAVE_PLATFORM_IMX_SSI - select IMX_HAVE_PLATFORM_SPI_IMX - select LEDS_GPIO_REGISTER - help - This adds board specific devices that can be found on Eukrea's - MBIMXSD evaluation board. - -endchoice - -config MACH_IMX25_DT - bool "Support i.MX25 platforms from device tree" - select SOC_IMX25 - help - Include support for Freescale i.MX25 based platforms - using the device tree for discovery - comment "MX27 platforms:" config MACH_MX27ADS @@ -557,6 +496,20 @@ config MACH_VPR200 endif +if ARCH_MULTI_V5 + +comment "Device tree only" + +config SOC_IMX25 + bool "i.MX25 support" + select ARCH_MXC_IOMUX_V3 + select CPU_ARM926T + select MXC_AVIC + select PINCTRL_IMX25 + help + This enables support for Freescale i.MX25 processor +endif + if ARCH_MULTI_V7 comment "Device tree only" @@ -635,9 +588,10 @@ config SOC_VF610 select ARM_GIC select PINCTRL_VF610 select PL310_ERRATA_769419 if CACHE_L2X0 + select SMP_ON_UP if SMP help - This enable support for Freescale Vybrid VF610 processor. + This enables support for Freescale Vybrid VF610 processor. choice prompt "Clocksource for scheduler clock" @@ -667,7 +621,7 @@ config SOC_LS1021A select ZONE_DMA if ARM_LPAE help - This enable support for Freescale LS1021A processor. + This enables support for Freescale LS1021A processor. endif diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile index 8d1b10180908..3244cf1d2773 100644 --- a/arch/arm/mach-imx/Makefile +++ b/arch/arm/mach-imx/Makefile @@ -3,7 +3,7 @@ obj-y := time.o cpu.o system.o irq-common.o obj-$(CONFIG_SOC_IMX1) += clk-imx1.o mm-imx1.o obj-$(CONFIG_SOC_IMX21) += clk-imx21.o mm-imx21.o -obj-$(CONFIG_SOC_IMX25) += clk-imx25.o mm-imx25.o ehci-imx25.o cpu-imx25.o +obj-$(CONFIG_SOC_IMX25) += clk-imx25.o cpu-imx25.o mach-imx25.o obj-$(CONFIG_SOC_IMX27) += cpu-imx27.o pm-imx27.o obj-$(CONFIG_SOC_IMX27) += clk-imx27.o mm-imx27.o ehci-imx27.o @@ -48,12 +48,6 @@ obj-$(CONFIG_MACH_IMX1_DT) += imx1-dt.o # i.MX21 based machines obj-$(CONFIG_MACH_MX21ADS) += mach-mx21ads.o -# i.MX25 based machines -obj-$(CONFIG_MACH_MX25_3DS) += mach-mx25_3ds.o -obj-$(CONFIG_MACH_EUKREA_CPUIMX25SD) += mach-eukrea_cpuimx25.o -obj-$(CONFIG_MACH_EUKREA_MBIMXSD25_BASEBOARD) += eukrea_mbimxsd25-baseboard.o -obj-$(CONFIG_MACH_IMX25_DT) += imx25-dt.o - # i.MX27 based machines obj-$(CONFIG_MACH_MX27ADS) += mach-mx27ads.o obj-$(CONFIG_MACH_MX27_3DS) += mach-mx27_3ds.o diff --git a/arch/arm/mach-imx/clk-imx25.c b/arch/arm/mach-imx/clk-imx25.c index 59c0c8558c6b..9c2633a9de9f 100644 --- a/arch/arm/mach-imx/clk-imx25.c +++ b/arch/arm/mach-imx/clk-imx25.c @@ -30,7 +30,6 @@ #include "clk.h" #include "common.h" #include "hardware.h" -#include "mx25.h" #define CCM_MPCTL 0x00 #define CCM_UPCTL 0x04 @@ -239,80 +238,6 @@ static int __init __mx25_clocks_init(unsigned long osc_rate, return 0; } -int __init mx25_clocks_init(void) -{ - void __iomem *ccm; - - ccm = ioremap(MX25_CRM_BASE_ADDR, SZ_16K); - - __mx25_clocks_init(24000000, ccm); - - clk_register_clkdev(clk[gpt1_ipg], "ipg", "imx-gpt.0"); - clk_register_clkdev(clk[gpt_ipg_per], "per", "imx-gpt.0"); - /* i.mx25 has the i.mx21 type uart */ - clk_register_clkdev(clk[uart1_ipg], "ipg", "imx21-uart.0"); - clk_register_clkdev(clk[uart_ipg_per], "per", "imx21-uart.0"); - clk_register_clkdev(clk[uart2_ipg], "ipg", "imx21-uart.1"); - clk_register_clkdev(clk[uart_ipg_per], "per", "imx21-uart.1"); - clk_register_clkdev(clk[uart3_ipg], "ipg", "imx21-uart.2"); - clk_register_clkdev(clk[uart_ipg_per], "per", "imx21-uart.2"); - clk_register_clkdev(clk[uart4_ipg], "ipg", "imx21-uart.3"); - clk_register_clkdev(clk[uart_ipg_per], "per", "imx21-uart.3"); - clk_register_clkdev(clk[uart5_ipg], "ipg", "imx21-uart.4"); - clk_register_clkdev(clk[uart_ipg_per], "per", "imx21-uart.4"); - clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.0"); - clk_register_clkdev(clk[usbotg_ahb], "ahb", "mxc-ehci.0"); - clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.0"); - clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.1"); - clk_register_clkdev(clk[usbotg_ahb], "ahb", "mxc-ehci.1"); - clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.1"); - clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.2"); - clk_register_clkdev(clk[usbotg_ahb], "ahb", "mxc-ehci.2"); - clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.2"); - clk_register_clkdev(clk[ipg], "ipg", "imx-udc-mx27"); - clk_register_clkdev(clk[usbotg_ahb], "ahb", "imx-udc-mx27"); - clk_register_clkdev(clk[usb_div], "per", "imx-udc-mx27"); - clk_register_clkdev(clk[nfc_ipg_per], NULL, "imx25-nand.0"); - /* i.mx25 has the i.mx35 type cspi */ - clk_register_clkdev(clk[cspi1_ipg], NULL, "imx35-cspi.0"); - clk_register_clkdev(clk[cspi2_ipg], NULL, "imx35-cspi.1"); - clk_register_clkdev(clk[cspi3_ipg], NULL, "imx35-cspi.2"); - clk_register_clkdev(clk[kpp_ipg], NULL, "imx-keypad"); - clk_register_clkdev(clk[tsc_ipg], NULL, "mx25-adc"); - clk_register_clkdev(clk[i2c_ipg_per], NULL, "imx21-i2c.0"); - clk_register_clkdev(clk[i2c_ipg_per], NULL, "imx21-i2c.1"); - clk_register_clkdev(clk[i2c_ipg_per], NULL, "imx21-i2c.2"); - clk_register_clkdev(clk[fec_ipg], "ipg", "imx25-fec.0"); - clk_register_clkdev(clk[fec_ahb], "ahb", "imx25-fec.0"); - clk_register_clkdev(clk[dryice_ipg], NULL, "imxdi_rtc.0"); - clk_register_clkdev(clk[lcdc_ipg_per], "per", "imx21-fb.0"); - clk_register_clkdev(clk[lcdc_ipg], "ipg", "imx21-fb.0"); - clk_register_clkdev(clk[lcdc_ahb], "ahb", "imx21-fb.0"); - clk_register_clkdev(clk[wdt_ipg], NULL, "imx2-wdt.0"); - clk_register_clkdev(clk[ssi1_ipg], NULL, "imx-ssi.0"); - clk_register_clkdev(clk[ssi2_ipg], NULL, "imx-ssi.1"); - clk_register_clkdev(clk[esdhc1_ipg_per], "per", "sdhci-esdhc-imx25.0"); - clk_register_clkdev(clk[esdhc1_ipg], "ipg", "sdhci-esdhc-imx25.0"); - clk_register_clkdev(clk[esdhc1_ahb], "ahb", "sdhci-esdhc-imx25.0"); - clk_register_clkdev(clk[esdhc2_ipg_per], "per", "sdhci-esdhc-imx25.1"); - clk_register_clkdev(clk[esdhc2_ipg], "ipg", "sdhci-esdhc-imx25.1"); - clk_register_clkdev(clk[esdhc2_ahb], "ahb", "sdhci-esdhc-imx25.1"); - clk_register_clkdev(clk[csi_ipg_per], "per", "imx25-camera.0"); - clk_register_clkdev(clk[csi_ipg], "ipg", "imx25-camera.0"); - clk_register_clkdev(clk[csi_ahb], "ahb", "imx25-camera.0"); - clk_register_clkdev(clk[dummy], "audmux", NULL); - clk_register_clkdev(clk[can1_ipg], NULL, "flexcan.0"); - clk_register_clkdev(clk[can2_ipg], NULL, "flexcan.1"); - /* i.mx25 has the i.mx35 type sdma */ - clk_register_clkdev(clk[sdma_ipg], "ipg", "imx35-sdma"); - clk_register_clkdev(clk[sdma_ahb], "ahb", "imx35-sdma"); - clk_register_clkdev(clk[iim_ipg], "iim", NULL); - - mxc_timer_init(MX25_IO_ADDRESS(MX25_GPT1_BASE_ADDR), MX25_INT_GPT1); - - return 0; -} - static void __init mx25_clocks_init_dt(struct device_node *np) { struct device_node *refnp; diff --git a/arch/arm/mach-imx/clk-imx6q.c b/arch/arm/mach-imx/clk-imx6q.c index d04a430607b8..469a150bf98f 100644 --- a/arch/arm/mach-imx/clk-imx6q.c +++ b/arch/arm/mach-imx/clk-imx6q.c @@ -119,6 +119,7 @@ static unsigned int share_count_asrc; static unsigned int share_count_ssi1; static unsigned int share_count_ssi2; static unsigned int share_count_ssi3; +static unsigned int share_count_mipi_core_cfg; static void __init imx6q_clocks_init(struct device_node *ccm_node) { @@ -246,6 +247,7 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node) clk[IMX6QDL_CLK_PLL3_60M] = imx_clk_fixed_factor("pll3_60m", "pll3_usb_otg", 1, 8); clk[IMX6QDL_CLK_TWD] = imx_clk_fixed_factor("twd", "arm", 1, 2); clk[IMX6QDL_CLK_GPT_3M] = imx_clk_fixed_factor("gpt_3m", "osc", 1, 8); + clk[IMX6QDL_CLK_VIDEO_27M] = imx_clk_fixed_factor("video_27m", "pll3_pfd1_540m", 1, 20); if (cpu_is_imx6dl()) { clk[IMX6QDL_CLK_GPU2D_AXI] = imx_clk_fixed_factor("gpu2d_axi", "mmdc_ch0_axi_podf", 1, 1); clk[IMX6QDL_CLK_GPU3D_AXI] = imx_clk_fixed_factor("gpu3d_axi", "mmdc_ch0_axi_podf", 1, 1); @@ -400,7 +402,7 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node) clk[IMX6QDL_CLK_GPU2D_CORE] = imx_clk_gate2("gpu2d_core", "gpu2d_core_podf", base + 0x6c, 24); clk[IMX6QDL_CLK_GPU3D_CORE] = imx_clk_gate2("gpu3d_core", "gpu3d_core_podf", base + 0x6c, 26); clk[IMX6QDL_CLK_HDMI_IAHB] = imx_clk_gate2("hdmi_iahb", "ahb", base + 0x70, 0); - clk[IMX6QDL_CLK_HDMI_ISFR] = imx_clk_gate2("hdmi_isfr", "pll3_pfd1_540m", base + 0x70, 4); + clk[IMX6QDL_CLK_HDMI_ISFR] = imx_clk_gate2("hdmi_isfr", "video_27m", base + 0x70, 4); clk[IMX6QDL_CLK_I2C1] = imx_clk_gate2("i2c1", "ipg_per", base + 0x70, 6); clk[IMX6QDL_CLK_I2C2] = imx_clk_gate2("i2c2", "ipg_per", base + 0x70, 8); clk[IMX6QDL_CLK_I2C3] = imx_clk_gate2("i2c3", "ipg_per", base + 0x70, 10); @@ -415,7 +417,9 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node) clk[IMX6QDL_CLK_LDB_DI0] = imx_clk_gate2("ldb_di0", "ldb_di0_podf", base + 0x74, 12); clk[IMX6QDL_CLK_LDB_DI1] = imx_clk_gate2("ldb_di1", "ldb_di1_podf", base + 0x74, 14); clk[IMX6QDL_CLK_IPU2_DI1] = imx_clk_gate2("ipu2_di1", "ipu2_di1_sel", base + 0x74, 10); - clk[IMX6QDL_CLK_HSI_TX] = imx_clk_gate2("hsi_tx", "hsi_tx_podf", base + 0x74, 16); + clk[IMX6QDL_CLK_HSI_TX] = imx_clk_gate2_shared("hsi_tx", "hsi_tx_podf", base + 0x74, 16, &share_count_mipi_core_cfg); + clk[IMX6QDL_CLK_MIPI_CORE_CFG] = imx_clk_gate2_shared("mipi_core_cfg", "video_27m", base + 0x74, 16, &share_count_mipi_core_cfg); + clk[IMX6QDL_CLK_MIPI_IPG] = imx_clk_gate2_shared("mipi_ipg", "ipg", base + 0x74, 16, &share_count_mipi_core_cfg); if (cpu_is_imx6dl()) /* * The multiplexer and divider of the imx6q clock gpu2d get diff --git a/arch/arm/mach-imx/common.h b/arch/arm/mach-imx/common.h index 1028b6c505c4..0f04e30b726d 100644 --- a/arch/arm/mach-imx/common.h +++ b/arch/arm/mach-imx/common.h @@ -23,13 +23,11 @@ struct of_device_id; void mx1_map_io(void); void mx21_map_io(void); -void mx25_map_io(void); void mx27_map_io(void); void mx31_map_io(void); void mx35_map_io(void); void imx1_init_early(void); void imx21_init_early(void); -void imx25_init_early(void); void imx27_init_early(void); void imx31_init_early(void); void imx35_init_early(void); @@ -37,13 +35,11 @@ void mxc_init_irq(void __iomem *); void tzic_init_irq(void); void mx1_init_irq(void); void mx21_init_irq(void); -void mx25_init_irq(void); void mx27_init_irq(void); void mx31_init_irq(void); void mx35_init_irq(void); void imx1_soc_init(void); void imx21_soc_init(void); -void imx25_soc_init(void); void imx27_soc_init(void); void imx31_soc_init(void); void imx35_soc_init(void); @@ -51,7 +47,6 @@ void epit_timer_init(void __iomem *base, int irq); void mxc_timer_init(void __iomem *, int); int mx1_clocks_init(unsigned long fref); int mx21_clocks_init(unsigned long lref, unsigned long fref); -int mx25_clocks_init(void); int mx27_clocks_init(unsigned long fref); int mx31_clocks_init(unsigned long fref); int mx35_clocks_init(void); @@ -71,6 +66,7 @@ unsigned int imx_get_soc_revision(void); void imx_init_revision_from_anatop(void); struct device *imx_soc_device_init(void); void imx6_enable_rbc(bool enable); +void imx_gpc_check_dt(void); void imx_gpc_set_arm_power_in_lpm(bool power_off); void imx_gpc_set_arm_power_up_timing(u32 sw2iso, u32 sw); void imx_gpc_set_arm_power_down_timing(u32 sw2iso, u32 sw); @@ -106,7 +102,6 @@ static inline void imx_scu_map_io(void) {} static inline void imx_smp_prepare(void) {} #endif void imx_src_init(void); -void imx_gpc_init(void); void imx_gpc_pre_suspend(bool arm_power_off); void imx_gpc_post_resume(void); void imx_gpc_mask_all(void); diff --git a/arch/arm/mach-imx/cpu-imx25.c b/arch/arm/mach-imx/cpu-imx25.c index 96ec64b5ff7d..d0ad67e802d3 100644 --- a/arch/arm/mach-imx/cpu-imx25.c +++ b/arch/arm/mach-imx/cpu-imx25.c @@ -11,6 +11,8 @@ */ #include #include +#include +#include #include "iim.h" #include "hardware.h" @@ -20,8 +22,15 @@ static int mx25_cpu_rev = -1; static int mx25_read_cpu_rev(void) { u32 rev; + void __iomem *iim_base; + struct device_node *np; + + np = of_find_compatible_node(NULL, NULL, "fsl,imx25-iim"); + iim_base = of_iomap(np, 0); + BUG_ON(!iim_base); + rev = readl(iim_base + MXC_IIMSREV); + iounmap(iim_base); - rev = __raw_readl(MX25_IO_ADDRESS(MX25_IIM_BASE_ADDR + MXC_IIMSREV)); switch (rev) { case 0x00: return IMX_CHIP_REVISION_1_0; diff --git a/arch/arm/mach-imx/devices-imx25.h b/arch/arm/mach-imx/devices-imx25.h deleted file mode 100644 index 61a114cddc39..000000000000 --- a/arch/arm/mach-imx/devices-imx25.h +++ /dev/null @@ -1,85 +0,0 @@ -/* - * Copyright (C) 2010 Pengutronix - * Uwe Kleine-Koenig - * - * This program is free software; you can redistribute it and/or modify it under - * the terms of the GNU General Public License version 2 as published by the - * Free Software Foundation. - */ -#include "devices/devices-common.h" - -extern const struct imx_fec_data imx25_fec_data; -#define imx25_add_fec(pdata) \ - imx_add_fec(&imx25_fec_data, pdata) - -extern const struct imx_flexcan_data imx25_flexcan_data[]; -#define imx25_add_flexcan(id) \ - imx_add_flexcan(&imx25_flexcan_data[id]) -#define imx25_add_flexcan0() imx25_add_flexcan(0) -#define imx25_add_flexcan1() imx25_add_flexcan(1) - -extern const struct imx_fsl_usb2_udc_data imx25_fsl_usb2_udc_data; -#define imx25_add_fsl_usb2_udc(pdata) \ - imx_add_fsl_usb2_udc(&imx25_fsl_usb2_udc_data, pdata) - -extern struct imx_imxdi_rtc_data imx25_imxdi_rtc_data; -#define imx25_add_imxdi_rtc() \ - imx_add_imxdi_rtc(&imx25_imxdi_rtc_data) - -extern const struct imx_imx2_wdt_data imx25_imx2_wdt_data; -#define imx25_add_imx2_wdt() \ - imx_add_imx2_wdt(&imx25_imx2_wdt_data) - -extern const struct imx_imx_fb_data imx25_imx_fb_data; -#define imx25_add_imx_fb(pdata) \ - imx_add_imx_fb(&imx25_imx_fb_data, pdata) - -extern const struct imx_imx_i2c_data imx25_imx_i2c_data[]; -#define imx25_add_imx_i2c(id, pdata) \ - imx_add_imx_i2c(&imx25_imx_i2c_data[id], pdata) -#define imx25_add_imx_i2c0(pdata) imx25_add_imx_i2c(0, pdata) -#define imx25_add_imx_i2c1(pdata) imx25_add_imx_i2c(1, pdata) -#define imx25_add_imx_i2c2(pdata) imx25_add_imx_i2c(2, pdata) - -extern const struct imx_imx_keypad_data imx25_imx_keypad_data; -#define imx25_add_imx_keypad(pdata) \ - imx_add_imx_keypad(&imx25_imx_keypad_data, pdata) - -extern const struct imx_imx_ssi_data imx25_imx_ssi_data[]; -#define imx25_add_imx_ssi(id, pdata) \ - imx_add_imx_ssi(&imx25_imx_ssi_data[id], pdata) - -extern const struct imx_imx_uart_1irq_data imx25_imx_uart_data[]; -#define imx25_add_imx_uart(id, pdata) \ - imx_add_imx_uart_1irq(&imx25_imx_uart_data[id], pdata) -#define imx25_add_imx_uart0(pdata) imx25_add_imx_uart(0, pdata) -#define imx25_add_imx_uart1(pdata) imx25_add_imx_uart(1, pdata) -#define imx25_add_imx_uart2(pdata) imx25_add_imx_uart(2, pdata) -#define imx25_add_imx_uart3(pdata) imx25_add_imx_uart(3, pdata) -#define imx25_add_imx_uart4(pdata) imx25_add_imx_uart(4, pdata) - -extern const struct imx_mx2_camera_data imx25_mx2_camera_data; -#define imx25_add_mx2_camera(pdata) \ - imx_add_mx2_camera(&imx25_mx2_camera_data, pdata) - -extern const struct imx_mxc_ehci_data imx25_mxc_ehci_otg_data; -#define imx25_add_mxc_ehci_otg(pdata) \ - imx_add_mxc_ehci(&imx25_mxc_ehci_otg_data, pdata) -extern const struct imx_mxc_ehci_data imx25_mxc_ehci_hs_data; -#define imx25_add_mxc_ehci_hs(pdata) \ - imx_add_mxc_ehci(&imx25_mxc_ehci_hs_data, pdata) - -extern const struct imx_mxc_nand_data imx25_mxc_nand_data; -#define imx25_add_mxc_nand(pdata) \ - imx_add_mxc_nand(&imx25_mxc_nand_data, pdata) - -extern const struct imx_sdhci_esdhc_imx_data imx25_sdhci_esdhc_imx_data[]; -#define imx25_add_sdhci_esdhc_imx(id, pdata) \ - imx_add_sdhci_esdhc_imx(&imx25_sdhci_esdhc_imx_data[id], pdata) - -extern const struct imx_spi_imx_data imx25_cspi_data[]; -#define imx25_add_spi_imx(id, pdata) \ - imx_add_spi_imx(&imx25_cspi_data[id], pdata) -#define imx25_add_spi_imx0(pdata) imx25_add_spi_imx(0, pdata) -#define imx25_add_spi_imx1(pdata) imx25_add_spi_imx(1, pdata) -#define imx25_add_spi_imx2(pdata) imx25_add_spi_imx(2, pdata) diff --git a/arch/arm/mach-imx/devices/Kconfig b/arch/arm/mach-imx/devices/Kconfig index 1d2cc1805f3e..3a552989248e 100644 --- a/arch/arm/mach-imx/devices/Kconfig +++ b/arch/arm/mach-imx/devices/Kconfig @@ -21,9 +21,6 @@ config IMX_HAVE_PLATFORM_IMX27_CODA config IMX_HAVE_PLATFORM_IMX2_WDT bool -config IMX_HAVE_PLATFORM_IMXDI_RTC - bool - config IMX_HAVE_PLATFORM_IMX_FB bool diff --git a/arch/arm/mach-imx/devices/Makefile b/arch/arm/mach-imx/devices/Makefile index 8fdb12b4ca7e..e5cf587bc1a0 100644 --- a/arch/arm/mach-imx/devices/Makefile +++ b/arch/arm/mach-imx/devices/Makefile @@ -8,7 +8,6 @@ obj-y += platform-gpio-mxc.o obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX21_HCD) += platform-imx21-hcd.o obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX27_CODA) += platform-imx27-coda.o obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX2_WDT) += platform-imx2-wdt.o -obj-$(CONFIG_IMX_HAVE_PLATFORM_IMXDI_RTC) += platform-imxdi_rtc.o obj-y += platform-imx-dma.o obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_FB) += platform-imx-fb.o obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_I2C) += platform-imx-i2c.o diff --git a/arch/arm/mach-imx/devices/platform-fec.c b/arch/arm/mach-imx/devices/platform-fec.c index d86f9250b4ee..b403a4fe2892 100644 --- a/arch/arm/mach-imx/devices/platform-fec.c +++ b/arch/arm/mach-imx/devices/platform-fec.c @@ -19,11 +19,6 @@ .irq = soc ## _INT_FEC, \ } -#ifdef CONFIG_SOC_IMX25 -const struct imx_fec_data imx25_fec_data __initconst = - imx_fec_data_entry_single(MX25, "imx25-fec"); -#endif /* ifdef CONFIG_SOC_IMX25 */ - #ifdef CONFIG_SOC_IMX27 const struct imx_fec_data imx27_fec_data __initconst = imx_fec_data_entry_single(MX27, "imx27-fec"); diff --git a/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c b/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c index 23b0061347cb..25e1de6f3a47 100644 --- a/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c +++ b/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c @@ -18,11 +18,6 @@ .irq = soc ## _INT_USB_OTG, \ } -#ifdef CONFIG_SOC_IMX25 -const struct imx_fsl_usb2_udc_data imx25_fsl_usb2_udc_data __initconst = - imx_fsl_usb2_udc_data_entry_single(MX25, "imx-udc-mx27"); -#endif /* ifdef CONFIG_SOC_IMX25 */ - #ifdef CONFIG_SOC_IMX27 const struct imx_fsl_usb2_udc_data imx27_fsl_usb2_udc_data __initconst = imx_fsl_usb2_udc_data_entry_single(MX27, "imx-udc-mx27"); diff --git a/arch/arm/mach-imx/devices/platform-imx-fb.c b/arch/arm/mach-imx/devices/platform-imx-fb.c index 25a47c616b2d..7df6328306f9 100644 --- a/arch/arm/mach-imx/devices/platform-imx-fb.c +++ b/arch/arm/mach-imx/devices/platform-imx-fb.c @@ -29,11 +29,6 @@ const struct imx_imx_fb_data imx21_imx_fb_data __initconst = imx_imx_fb_data_entry_single(MX21, "imx21-fb", SZ_4K); #endif /* ifdef CONFIG_SOC_IMX21 */ -#ifdef CONFIG_SOC_IMX25 -const struct imx_imx_fb_data imx25_imx_fb_data __initconst = - imx_imx_fb_data_entry_single(MX25, "imx21-fb", SZ_16K); -#endif /* ifdef CONFIG_SOC_IMX25 */ - #ifdef CONFIG_SOC_IMX27 const struct imx_imx_fb_data imx27_imx_fb_data __initconst = imx_imx_fb_data_entry_single(MX27, "imx21-fb", SZ_4K); diff --git a/arch/arm/mach-imx/devices/platform-imx-i2c.c b/arch/arm/mach-imx/devices/platform-imx-i2c.c index 644ac2689882..ae9791522fc8 100644 --- a/arch/arm/mach-imx/devices/platform-imx-i2c.c +++ b/arch/arm/mach-imx/devices/platform-imx-i2c.c @@ -31,16 +31,6 @@ const struct imx_imx_i2c_data imx21_imx_i2c_data __initconst = imx_imx_i2c_data_entry_single(MX21, "imx21-i2c", 0, , SZ_4K); #endif /* ifdef CONFIG_SOC_IMX21 */ -#ifdef CONFIG_SOC_IMX25 -const struct imx_imx_i2c_data imx25_imx_i2c_data[] __initconst = { -#define imx25_imx_i2c_data_entry(_id, _hwid) \ - imx_imx_i2c_data_entry(MX25, "imx21-i2c", _id, _hwid, SZ_16K) - imx25_imx_i2c_data_entry(0, 1), - imx25_imx_i2c_data_entry(1, 2), - imx25_imx_i2c_data_entry(2, 3), -}; -#endif /* ifdef CONFIG_SOC_IMX25 */ - #ifdef CONFIG_SOC_IMX27 const struct imx_imx_i2c_data imx27_imx_i2c_data[] __initconst = { #define imx27_imx_i2c_data_entry(_id, _hwid) \ diff --git a/arch/arm/mach-imx/devices/platform-imx-keypad.c b/arch/arm/mach-imx/devices/platform-imx-keypad.c index f42200b7aca9..479e4d70dbf9 100644 --- a/arch/arm/mach-imx/devices/platform-imx-keypad.c +++ b/arch/arm/mach-imx/devices/platform-imx-keypad.c @@ -21,11 +21,6 @@ const struct imx_imx_keypad_data imx21_imx_keypad_data __initconst = imx_imx_keypad_data_entry_single(MX21, SZ_16); #endif /* ifdef CONFIG_SOC_IMX21 */ -#ifdef CONFIG_SOC_IMX25 -const struct imx_imx_keypad_data imx25_imx_keypad_data __initconst = - imx_imx_keypad_data_entry_single(MX25, SZ_16K); -#endif /* ifdef CONFIG_SOC_IMX25 */ - #ifdef CONFIG_SOC_IMX27 const struct imx_imx_keypad_data imx27_imx_keypad_data __initconst = imx_imx_keypad_data_entry_single(MX27, SZ_16); diff --git a/arch/arm/mach-imx/devices/platform-imx-ssi.c b/arch/arm/mach-imx/devices/platform-imx-ssi.c index 1c7c721ebff1..6f0e94eb29ee 100644 --- a/arch/arm/mach-imx/devices/platform-imx-ssi.c +++ b/arch/arm/mach-imx/devices/platform-imx-ssi.c @@ -30,15 +30,6 @@ const struct imx_imx_ssi_data imx21_imx_ssi_data[] __initconst = { }; #endif /* ifdef CONFIG_SOC_IMX21 */ -#ifdef CONFIG_SOC_IMX25 -const struct imx_imx_ssi_data imx25_imx_ssi_data[] __initconst = { -#define imx25_imx_ssi_data_entry(_id, _hwid) \ - imx_imx_ssi_data_entry(MX25, _id, _hwid, SZ_4K) - imx25_imx_ssi_data_entry(0, 1), - imx25_imx_ssi_data_entry(1, 2), -}; -#endif /* ifdef CONFIG_SOC_IMX25 */ - #ifdef CONFIG_SOC_IMX27 const struct imx_imx_ssi_data imx27_imx_ssi_data[] __initconst = { #define imx27_imx_ssi_data_entry(_id, _hwid) \ diff --git a/arch/arm/mach-imx/devices/platform-imx-uart.c b/arch/arm/mach-imx/devices/platform-imx-uart.c index 8c01836bc1d4..6962cff4a950 100644 --- a/arch/arm/mach-imx/devices/platform-imx-uart.c +++ b/arch/arm/mach-imx/devices/platform-imx-uart.c @@ -47,18 +47,6 @@ const struct imx_imx_uart_1irq_data imx21_imx_uart_data[] __initconst = { }; #endif -#ifdef CONFIG_SOC_IMX25 -const struct imx_imx_uart_1irq_data imx25_imx_uart_data[] __initconst = { -#define imx25_imx_uart_data_entry(_id, _hwid) \ - imx_imx_uart_1irq_data_entry(MX25, _id, _hwid, SZ_16K) - imx25_imx_uart_data_entry(0, 1), - imx25_imx_uart_data_entry(1, 2), - imx25_imx_uart_data_entry(2, 3), - imx25_imx_uart_data_entry(3, 4), - imx25_imx_uart_data_entry(4, 5), -}; -#endif /* ifdef CONFIG_SOC_IMX25 */ - #ifdef CONFIG_SOC_IMX27 const struct imx_imx_uart_1irq_data imx27_imx_uart_data[] __initconst = { #define imx27_imx_uart_data_entry(_id, _hwid) \ diff --git a/arch/arm/mach-imx/devices/platform-imx2-wdt.c b/arch/arm/mach-imx/devices/platform-imx2-wdt.c index 54f63bc25ca4..8c134c8d7500 100644 --- a/arch/arm/mach-imx/devices/platform-imx2-wdt.c +++ b/arch/arm/mach-imx/devices/platform-imx2-wdt.c @@ -25,11 +25,6 @@ const struct imx_imx2_wdt_data imx21_imx2_wdt_data __initconst = imx_imx2_wdt_data_entry_single(MX21, 0, , SZ_4K); #endif /* ifdef CONFIG_SOC_IMX21 */ -#ifdef CONFIG_SOC_IMX25 -const struct imx_imx2_wdt_data imx25_imx2_wdt_data __initconst = - imx_imx2_wdt_data_entry_single(MX25, 0, , SZ_16K); -#endif /* ifdef CONFIG_SOC_IMX25 */ - #ifdef CONFIG_SOC_IMX27 const struct imx_imx2_wdt_data imx27_imx2_wdt_data __initconst = imx_imx2_wdt_data_entry_single(MX27, 0, , SZ_4K); diff --git a/arch/arm/mach-imx/devices/platform-imxdi_rtc.c b/arch/arm/mach-imx/devices/platform-imxdi_rtc.c deleted file mode 100644 index 5bb490d556ea..000000000000 --- a/arch/arm/mach-imx/devices/platform-imxdi_rtc.c +++ /dev/null @@ -1,42 +0,0 @@ -/* - * Copyright (C) 2010 Pengutronix - * Uwe Kleine-Koenig - * - * This program is free software; you can redistribute it and/or modify it under - * the terms of the GNU General Public License version 2 as published by the - * Free Software Foundation. - */ -#include - -#include "../hardware.h" -#include "devices-common.h" - -#define imx_imxdi_rtc_data_entry_single(soc) \ - { \ - .iobase = soc ## _DRYICE_BASE_ADDR, \ - .irq = soc ## _INT_DRYICE, \ - } - -#ifdef CONFIG_SOC_IMX25 -const struct imx_imxdi_rtc_data imx25_imxdi_rtc_data __initconst = - imx_imxdi_rtc_data_entry_single(MX25); -#endif /* ifdef CONFIG_SOC_IMX25 */ - -struct platform_device *__init imx_add_imxdi_rtc( - const struct imx_imxdi_rtc_data *data) -{ - struct resource res[] = { - { - .start = data->iobase, - .end = data->iobase + SZ_16K - 1, - .flags = IORESOURCE_MEM, - }, { - .start = data->irq, - .end = data->irq, - .flags = IORESOURCE_IRQ, - }, - }; - - return imx_add_platform_device("imxdi_rtc", 0, - res, ARRAY_SIZE(res), NULL, 0); -} diff --git a/arch/arm/mach-imx/devices/platform-mx2-camera.c b/arch/arm/mach-imx/devices/platform-mx2-camera.c index b53e1f348f51..4c377c33242c 100644 --- a/arch/arm/mach-imx/devices/platform-mx2-camera.c +++ b/arch/arm/mach-imx/devices/platform-mx2-camera.c @@ -27,11 +27,6 @@ .irqemmaprp = soc ## _INT_EMMAPRP, \ } -#ifdef CONFIG_SOC_IMX25 -const struct imx_mx2_camera_data imx25_mx2_camera_data __initconst = - imx_mx2_camera_data_entry_single(MX25, "imx25-camera"); -#endif /* ifdef CONFIG_SOC_IMX25 */ - #ifdef CONFIG_SOC_IMX27 const struct imx_mx2_camera_data imx27_mx2_camera_data __initconst = imx_mx2_camera_data_entry_single_emma(MX27, "imx27-camera"); diff --git a/arch/arm/mach-imx/devices/platform-mxc-ehci.c b/arch/arm/mach-imx/devices/platform-mxc-ehci.c index 296353662ff0..4537abd2a8f2 100644 --- a/arch/arm/mach-imx/devices/platform-mxc-ehci.c +++ b/arch/arm/mach-imx/devices/platform-mxc-ehci.c @@ -18,13 +18,6 @@ .irq = soc ## _INT_USB_ ## hs, \ } -#ifdef CONFIG_SOC_IMX25 -const struct imx_mxc_ehci_data imx25_mxc_ehci_otg_data __initconst = - imx_mxc_ehci_data_entry_single(MX25, 0, OTG); -const struct imx_mxc_ehci_data imx25_mxc_ehci_hs_data __initconst = - imx_mxc_ehci_data_entry_single(MX25, 1, HS); -#endif /* ifdef CONFIG_SOC_IMX25 */ - #ifdef CONFIG_SOC_IMX27 const struct imx_mxc_ehci_data imx27_mxc_ehci_otg_data __initconst = imx_mxc_ehci_data_entry_single(MX27, 0, OTG); diff --git a/arch/arm/mach-imx/devices/platform-mxc_nand.c b/arch/arm/mach-imx/devices/platform-mxc_nand.c index fa618a34f462..676df4920c7b 100644 --- a/arch/arm/mach-imx/devices/platform-mxc_nand.c +++ b/arch/arm/mach-imx/devices/platform-mxc_nand.c @@ -34,11 +34,6 @@ const struct imx_mxc_nand_data imx21_mxc_nand_data __initconst = imx_mxc_nand_data_entry_single(MX21, "imx21-nand", SZ_4K); #endif /* ifdef CONFIG_SOC_IMX21 */ -#ifdef CONFIG_SOC_IMX25 -const struct imx_mxc_nand_data imx25_mxc_nand_data __initconst = - imx_mxc_nand_data_entry_single(MX25, "imx25-nand", SZ_8K); -#endif /* ifdef CONFIG_SOC_IMX25 */ - #ifdef CONFIG_SOC_IMX27 const struct imx_mxc_nand_data imx27_mxc_nand_data __initconst = imx_mxc_nand_data_entry_single(MX27, "imx27-nand", SZ_4K); diff --git a/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c b/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c index fb8d4a2ad48c..a5edd7d60266 100644 --- a/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c +++ b/arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c @@ -1,5 +1,5 @@ /* - * Copyright (C) 2010 Pengutronix, Wolfram Sang + * Copyright (C) 2010 Pengutronix, Wolfram Sang * * This program is free software; you can redistribute it and/or modify it under * the terms of the GNU General Public License version 2 as published by the diff --git a/arch/arm/mach-imx/devices/platform-spi_imx.c b/arch/arm/mach-imx/devices/platform-spi_imx.c index aca825d74c48..5e9707b47f92 100644 --- a/arch/arm/mach-imx/devices/platform-spi_imx.c +++ b/arch/arm/mach-imx/devices/platform-spi_imx.c @@ -39,17 +39,6 @@ const struct imx_spi_imx_data imx21_cspi_data[] __initconst = { }; #endif -#ifdef CONFIG_SOC_IMX25 -/* i.mx25 has the i.mx35 type cspi */ -const struct imx_spi_imx_data imx25_cspi_data[] __initconst = { -#define imx25_cspi_data_entry(_id, _hwid) \ - imx_spi_imx_data_entry(MX25, CSPI, "imx35-cspi", _id, _hwid, SZ_16K) - imx25_cspi_data_entry(0, 1), - imx25_cspi_data_entry(1, 2), - imx25_cspi_data_entry(2, 3), -}; -#endif /* ifdef CONFIG_SOC_IMX25 */ - #ifdef CONFIG_SOC_IMX27 const struct imx_spi_imx_data imx27_cspi_data[] __initconst = { #define imx27_cspi_data_entry(_id, _hwid) \ diff --git a/arch/arm/mach-imx/ehci-imx25.c b/arch/arm/mach-imx/ehci-imx25.c deleted file mode 100644 index 42a5a3d14c5f..000000000000 --- a/arch/arm/mach-imx/ehci-imx25.c +++ /dev/null @@ -1,99 +0,0 @@ -/* - * Copyright (c) 2009 Daniel Mack - * Copyright (C) 2010 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * This program is distributed in the hope that it will be useful, but - * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY - * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License - * for more details. - */ - -#include -#include -#include - -#include "ehci.h" -#include "hardware.h" - -#define USBCTRL_OTGBASE_OFFSET 0x600 - -#define MX25_OTG_SIC_SHIFT 29 -#define MX25_OTG_SIC_MASK (0x3 << MX25_OTG_SIC_SHIFT) -#define MX25_OTG_PM_BIT (1 << 24) -#define MX25_OTG_PP_BIT (1 << 11) -#define MX25_OTG_OCPOL_BIT (1 << 3) - -#define MX25_H1_SIC_SHIFT 21 -#define MX25_H1_SIC_MASK (0x3 << MX25_H1_SIC_SHIFT) -#define MX25_H1_PP_BIT (1 << 18) -#define MX25_H1_PM_BIT (1 << 16) -#define MX25_H1_IPPUE_UP_BIT (1 << 7) -#define MX25_H1_IPPUE_DOWN_BIT (1 << 6) -#define MX25_H1_TLL_BIT (1 << 5) -#define MX25_H1_USBTE_BIT (1 << 4) -#define MX25_H1_OCPOL_BIT (1 << 2) - -int mx25_initialize_usb_hw(int port, unsigned int flags) -{ - unsigned int v; - - v = readl(MX25_IO_ADDRESS(MX25_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET)); - - switch (port) { - case 0: /* OTG port */ - v &= ~(MX25_OTG_SIC_MASK | MX25_OTG_PM_BIT | MX25_OTG_PP_BIT | - MX25_OTG_OCPOL_BIT); - v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_OTG_SIC_SHIFT; - - if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) - v |= MX25_OTG_PM_BIT; - - if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) - v |= MX25_OTG_PP_BIT; - - if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)) - v |= MX25_OTG_OCPOL_BIT; - - break; - case 1: /* H1 port */ - v &= ~(MX25_H1_SIC_MASK | MX25_H1_PM_BIT | MX25_H1_PP_BIT | - MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT | MX25_H1_USBTE_BIT | - MX25_H1_IPPUE_DOWN_BIT | MX25_H1_IPPUE_UP_BIT); - v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_H1_SIC_SHIFT; - - if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) - v |= MX25_H1_PM_BIT; - - if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) - v |= MX25_H1_PP_BIT; - - if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)) - v |= MX25_H1_OCPOL_BIT; - - if (!(flags & MXC_EHCI_TTL_ENABLED)) - v |= MX25_H1_TLL_BIT; - - if (flags & MXC_EHCI_INTERNAL_PHY) - v |= MX25_H1_USBTE_BIT; - - if (flags & MXC_EHCI_IPPUE_DOWN) - v |= MX25_H1_IPPUE_DOWN_BIT; - - if (flags & MXC_EHCI_IPPUE_UP) - v |= MX25_H1_IPPUE_UP_BIT; - - break; - default: - return -EINVAL; - } - - writel(v, MX25_IO_ADDRESS(MX25_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET)); - - return 0; -} - diff --git a/arch/arm/mach-imx/eukrea_mbimxsd25-baseboard.c b/arch/arm/mach-imx/eukrea_mbimxsd25-baseboard.c deleted file mode 100644 index e77cc3af6db2..000000000000 --- a/arch/arm/mach-imx/eukrea_mbimxsd25-baseboard.c +++ /dev/null @@ -1,310 +0,0 @@ -/* - * Copyright (C) 2010 Eric Benard - eric@eukrea.com - * - * Based on pcm970-baseboard.c which is : - * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de) - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - * MA 02110-1301, USA. - */ - -#include -#include -#include -#include -#include -#include