powerpc/pseries: Set error_state to pci_channel_io_normal in eeh_report_reset()

While adding native EEH support to Emulex and Qlogic drivers, it was
discovered that dev->error_state was set to pci_io_channel_normal too
late in the recovery process. These drivers rely on error_state to
determine if they can access the device in their slot_reset callback,
thus error_state needs to be set to pci_io_channel_normal in
eeh_report_reset(). Below is a detailed explanation (courtesy of Richard
Lary) as to why this is necessary.

Background:
PCI MMIO or DMA accesses to a frozen slot generate additional EEH
errors. If the number of additional EEH errors exceeds EEH_MAX_FAILS the
adapter will be shutdown. To avoid triggering excessive EEH errors and
an undesirable adapter shutdown, some drivers use the
pci_channel_offline(dev) wrapper function to return a Boolean value
based on the value of pci_dev->error_state to determine if PCI MMIO or
DMA accesses are safe. If the wrapper returns TRUE, drivers must not
make PCI MMIO or DMA access to their hardware.

The pci_dev structure member error_state reflects one of three values,
1) pci_channel_io_normal, 2) pci_channel_io_frozen, 3)
pci_channel_io_perm_failure.  Function pci_channel_offline(dev) returns
TRUE if error_state is pci_channel_io_frozen or pci_channel_io_perm_failure.

The EEH driver sets pci_dev->error_state to pci_channel_io_frozen at the
point where the PCI slot is frozen. Currently, the EEH driver restores
dev->error_state to pci_channel_io_normal in eeh_report_resume() before
calling the driver's resume callback. However, when the EEH driver calls
the driver's slot_reset callback() from eeh_report_reset(), it
incorrectly indicates the error state is still pci_channel_io_frozen.

Waiting until eeh_report_resume() to restore dev->error_state to
pci_channel_io_normal is too late for Emulex and QLogic FC drivers and
any other drivers which are designed to use common code paths in these
two cases: i) those called after the driver's slot_reset callback() and
ii) those called after the PCI slot is frozen but before the driver's
slot_reset callback is called. Case i) all driver paths executed to
reinitialize the hardware after a reset and case ii) all code paths
executed by driver kernel threads that run asynchronous to the main
driver thread, such as interrupt handlers and worker threads to process
driver work queues.

Emulex and QLogic FC drivers are designed with common code paths which
require that pci_channel_offline(dev) reflect the true state of the
hardware. The state transitions that the hardware takes from Normal
Operations to Slot Frozen to Reset to Normal Operations are documented
in the Power Architecture™ Platform Requirements+ (PAPR+) in Table 75.
PE State Control.

PAPR defines the following 3 states:

0 -- Not reset, Not EEH stopped, MMIO load/store allowed, DMA allowed
     (Normal Operations)
1 -- Reset, Not EEH stopped, MMIO load/store disabled, DMA disabled
2 -- Not reset, EEH stopped, MMIO load/store disabled, DMA disabled
     (Slot Frozen)

An EEH error places the slot in state 2 (Frozen) and the adapter driver
is notified that an EEH error was detected. If the adapter driver
returns PCI_ERS_RESULT_NEED_RESET, the EEH driver calls
eeh_reset_device() to place the slot into state 1 (Reset) and
eeh_reset_device completes by placing the slot into State 0 (Normal
Operations). Upon return from eeh_reset_device(), the EEH driver calls
eeh_report_reset, which then calls the adapter's slot_reset callback. At
the time the adapter's slot_reset callback is called, the true state of
the hardware is Normal Operations and should be accurately reflected by
setting dev->error_state to pci_channel_io_normal.

The current implementation of EEH driver does not do so and requires
this change to correct this deficiency.

Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

arch/powerpc/platforms/pseries/eeh_driver.c

@@ -182,6 +182,8 @@ static void eeh_report_reset(struct pci_dev *dev, void *userdata)
 	if (!driver)
 		return;
 
+	dev->error_state = pci_channel_io_normal;
+
 	eeh_enable_irq(dev);
 
 	if (!driver->err_handler ||