Input: ili210x - add ili251x firmware update support
The ili251x firmware can be updated, this is used when switching between different modes of operation of the touch surface, e.g. glove operation. This patch implements the firmware update mechanism triggered by a write into an sysfs attribute. The firmware itself is distributed as an intel hex file with non-standard types. The first two lines are of type 0xad, which indicates the start of DataFlash payload, that is always at address 0xf000 on the ili251x, so it can be dropped, and 0xac which indicates the position of firmware info in the Application payload, that is always at address 0x2020 on the ili251x and we do not care. The rest of the firmware is data of type 0x00, and we care about that. To convert the firmware hex file into something usable by the kernel, remove the first two lines and then use ihex2fw: $ tail -n +3 input.hex > temp.hex $ ./tools/firmware/ihex2fw temp.hex firmware/ilitek/ili251x.bin To trigger the firmware update, place firmware file ilitek/ili251x.bin into /lib/firmware/, write into firmware_update sysfs attribute and wait about 30-40 seconds. The firmware update is slow. Afterward, verify the firmware_version and mode sysfs attributes to check whether the firmware got updated and the controller switched back to application (AP) mode by reading out 'mode' attribute in sysfs. Note that the content of firmware_version, e.g. 0600.0005.abcd.aa04 can be matched to the content of the firmware hex file. The first four bytes, 0x06 0x00 0x00 0x05 can be found at ^:102030 00 05000006, the next four bytes 0xab 0xcd 0xaa 0x04 at ^:10F000 00 nnnnnnnn ABCDAA04. Note that the protocol differs considerably between the ili2xxx devices, this patch therefore implements this functionality only for ili251x that I can test. Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20210831202506.181927-3-marex@denx.de Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This commit is contained in:
Родитель
70a7681db0
Коммит
c6ac8f0b4c
|
@ -425,6 +425,7 @@ config TOUCHSCREEN_HYCON_HY46XX
|
||||||
config TOUCHSCREEN_ILI210X
|
config TOUCHSCREEN_ILI210X
|
||||||
tristate "Ilitek ILI210X based touchscreen"
|
tristate "Ilitek ILI210X based touchscreen"
|
||||||
depends on I2C
|
depends on I2C
|
||||||
|
select CRC_CCITT
|
||||||
help
|
help
|
||||||
Say Y here if you have a ILI210X based touchscreen
|
Say Y here if you have a ILI210X based touchscreen
|
||||||
controller. This driver supports models ILI2102,
|
controller. This driver supports models ILI2102,
|
||||||
|
|
|
@ -1,7 +1,9 @@
|
||||||
// SPDX-License-Identifier: GPL-2.0-only
|
// SPDX-License-Identifier: GPL-2.0-only
|
||||||
|
#include <linux/crc-ccitt.h>
|
||||||
#include <linux/delay.h>
|
#include <linux/delay.h>
|
||||||
#include <linux/gpio/consumer.h>
|
#include <linux/gpio/consumer.h>
|
||||||
#include <linux/i2c.h>
|
#include <linux/i2c.h>
|
||||||
|
#include <linux/ihex.h>
|
||||||
#include <linux/input.h>
|
#include <linux/input.h>
|
||||||
#include <linux/input/mt.h>
|
#include <linux/input/mt.h>
|
||||||
#include <linux/input/touchscreen.h>
|
#include <linux/input/touchscreen.h>
|
||||||
|
@ -25,11 +27,20 @@
|
||||||
#define REG_FIRMWARE_VERSION 0x40
|
#define REG_FIRMWARE_VERSION 0x40
|
||||||
#define REG_PROTOCOL_VERSION 0x42
|
#define REG_PROTOCOL_VERSION 0x42
|
||||||
#define REG_KERNEL_VERSION 0x61
|
#define REG_KERNEL_VERSION 0x61
|
||||||
|
#define REG_IC_BUSY 0x80
|
||||||
|
#define REG_IC_BUSY_NOT_BUSY 0x50
|
||||||
#define REG_GET_MODE 0xc0
|
#define REG_GET_MODE 0xc0
|
||||||
#define REG_GET_MODE_AP 0x5a
|
#define REG_GET_MODE_AP 0x5a
|
||||||
#define REG_GET_MODE_BL 0x55
|
#define REG_GET_MODE_BL 0x55
|
||||||
|
#define REG_SET_MODE_AP 0xc1
|
||||||
|
#define REG_SET_MODE_BL 0xc2
|
||||||
|
#define REG_WRITE_DATA 0xc3
|
||||||
|
#define REG_WRITE_ENABLE 0xc4
|
||||||
|
#define REG_READ_DATA_CRC 0xc7
|
||||||
#define REG_CALIBRATE 0xcc
|
#define REG_CALIBRATE 0xcc
|
||||||
|
|
||||||
|
#define ILI251X_FW_FILENAME "ilitek/ili251x.bin"
|
||||||
|
|
||||||
struct ili2xxx_chip {
|
struct ili2xxx_chip {
|
||||||
int (*read_reg)(struct i2c_client *client, u8 reg,
|
int (*read_reg)(struct i2c_client *client, u8 reg,
|
||||||
void *buf, size_t len);
|
void *buf, size_t len);
|
||||||
|
@ -546,8 +557,305 @@ static ssize_t ili210x_calibrate(struct device *dev,
|
||||||
}
|
}
|
||||||
static DEVICE_ATTR(calibrate, S_IWUSR, NULL, ili210x_calibrate);
|
static DEVICE_ATTR(calibrate, S_IWUSR, NULL, ili210x_calibrate);
|
||||||
|
|
||||||
|
static int ili251x_firmware_to_buffer(const struct firmware *fw,
|
||||||
|
u8 **buf, u16 *ac_end, u16 *df_end)
|
||||||
|
{
|
||||||
|
const struct ihex_binrec *rec;
|
||||||
|
u32 fw_addr, fw_last_addr = 0;
|
||||||
|
u16 fw_len;
|
||||||
|
u8 *fw_buf;
|
||||||
|
int error;
|
||||||
|
|
||||||
|
/*
|
||||||
|
* The firmware ihex blob can never be bigger than 64 kiB, so make this
|
||||||
|
* simple -- allocate a 64 kiB buffer, iterate over the ihex blob records
|
||||||
|
* once, copy them all into this buffer at the right locations, and then
|
||||||
|
* do all operations on this linear buffer.
|
||||||
|
*/
|
||||||
|
fw_buf = kzalloc(SZ_64K, GFP_KERNEL);
|
||||||
|
if (!fw_buf)
|
||||||
|
return -ENOMEM;
|
||||||
|
|
||||||
|
rec = (const struct ihex_binrec *)fw->data;
|
||||||
|
while (rec) {
|
||||||
|
fw_addr = be32_to_cpu(rec->addr);
|
||||||
|
fw_len = be16_to_cpu(rec->len);
|
||||||
|
|
||||||
|
/* The last 32 Byte firmware block can be 0xffe0 */
|
||||||
|
if (fw_addr + fw_len > SZ_64K || fw_addr > SZ_64K - 32) {
|
||||||
|
error = -EFBIG;
|
||||||
|
goto err_big;
|
||||||
|
}
|
||||||
|
|
||||||
|
/* Find the last address before DF start address, that is AC end */
|
||||||
|
if (fw_addr == 0xf000)
|
||||||
|
*ac_end = fw_last_addr;
|
||||||
|
fw_last_addr = fw_addr + fw_len;
|
||||||
|
|
||||||
|
memcpy(fw_buf + fw_addr, rec->data, fw_len);
|
||||||
|
rec = ihex_next_binrec(rec);
|
||||||
|
}
|
||||||
|
|
||||||
|
/* DF end address is the last address in the firmware blob */
|
||||||
|
*df_end = fw_addr + fw_len;
|
||||||
|
*buf = fw_buf;
|
||||||
|
return 0;
|
||||||
|
|
||||||
|
err_big:
|
||||||
|
kfree(fw_buf);
|
||||||
|
return error;
|
||||||
|
}
|
||||||
|
|
||||||
|
/* Switch mode between Application and BootLoader */
|
||||||
|
static int ili251x_switch_ic_mode(struct i2c_client *client, u8 cmd_mode)
|
||||||
|
{
|
||||||
|
struct ili210x *priv = i2c_get_clientdata(client);
|
||||||
|
u8 cmd_wren[3] = { REG_WRITE_ENABLE, 0x5a, 0xa5 };
|
||||||
|
u8 md[2];
|
||||||
|
int error;
|
||||||
|
|
||||||
|
error = priv->chip->read_reg(client, REG_GET_MODE, md, sizeof(md));
|
||||||
|
if (error)
|
||||||
|
return error;
|
||||||
|
/* Mode already set */
|
||||||
|
if ((cmd_mode == REG_SET_MODE_AP && md[0] == REG_GET_MODE_AP) ||
|
||||||
|
(cmd_mode == REG_SET_MODE_BL && md[0] == REG_GET_MODE_BL))
|
||||||
|
return 0;
|
||||||
|
|
||||||
|
/* Unlock writes */
|
||||||
|
error = i2c_master_send(client, cmd_wren, sizeof(cmd_wren));
|
||||||
|
if (error != sizeof(cmd_wren))
|
||||||
|
return -EINVAL;
|
||||||
|
|
||||||
|
mdelay(20);
|
||||||
|
|
||||||
|
/* Select mode (BootLoader or Application) */
|
||||||
|
error = i2c_master_send(client, &cmd_mode, 1);
|
||||||
|
if (error != 1)
|
||||||
|
return -EINVAL;
|
||||||
|
|
||||||
|
mdelay(200); /* Reboot into bootloader takes a lot of time ... */
|
||||||
|
|
||||||
|
/* Read back mode */
|
||||||
|
error = priv->chip->read_reg(client, REG_GET_MODE, md, sizeof(md));
|
||||||
|
if (error)
|
||||||
|
return error;
|
||||||
|
/* Check if mode is correct now. */
|
||||||
|
if ((cmd_mode == REG_SET_MODE_AP && md[0] == REG_GET_MODE_AP) ||
|
||||||
|
(cmd_mode == REG_SET_MODE_BL && md[0] == REG_GET_MODE_BL))
|
||||||
|
return 0;
|
||||||
|
|
||||||
|
return -EINVAL;
|
||||||
|
}
|
||||||
|
|
||||||
|
static int ili251x_firmware_busy(struct i2c_client *client)
|
||||||
|
{
|
||||||
|
struct ili210x *priv = i2c_get_clientdata(client);
|
||||||
|
int error, i = 0;
|
||||||
|
u8 data;
|
||||||
|
|
||||||
|
do {
|
||||||
|
/* The read_reg already contains suitable delay */
|
||||||
|
error = priv->chip->read_reg(client, REG_IC_BUSY, &data, 1);
|
||||||
|
if (error)
|
||||||
|
return error;
|
||||||
|
if (i++ == 100000)
|
||||||
|
return -ETIMEDOUT;
|
||||||
|
} while (data != REG_IC_BUSY_NOT_BUSY);
|
||||||
|
|
||||||
|
return 0;
|
||||||
|
}
|
||||||
|
|
||||||
|
static int ili251x_firmware_write_to_ic(struct device *dev, u8 *fwbuf,
|
||||||
|
u16 start, u16 end, u8 dataflash)
|
||||||
|
{
|
||||||
|
struct i2c_client *client = to_i2c_client(dev);
|
||||||
|
struct ili210x *priv = i2c_get_clientdata(client);
|
||||||
|
u8 cmd_crc = REG_READ_DATA_CRC;
|
||||||
|
u8 crcrb[4] = { 0 };
|
||||||
|
u8 fw_data[33];
|
||||||
|
u16 fw_addr;
|
||||||
|
int error;
|
||||||
|
|
||||||
|
/*
|
||||||
|
* The DF (dataflash) needs 2 bytes offset for unknown reasons,
|
||||||
|
* the AC (application) has 2 bytes CRC16-CCITT at the end.
|
||||||
|
*/
|
||||||
|
u16 crc = crc_ccitt(0, fwbuf + start + (dataflash ? 2 : 0),
|
||||||
|
end - start - 2);
|
||||||
|
|
||||||
|
/* Unlock write to either AC (application) or DF (dataflash) area */
|
||||||
|
u8 cmd_wr[10] = {
|
||||||
|
REG_WRITE_ENABLE, 0x5a, 0xa5, dataflash,
|
||||||
|
(end >> 16) & 0xff, (end >> 8) & 0xff, end & 0xff,
|
||||||
|
(crc >> 16) & 0xff, (crc >> 8) & 0xff, crc & 0xff
|
||||||
|
};
|
||||||
|
|
||||||
|
error = i2c_master_send(client, cmd_wr, sizeof(cmd_wr));
|
||||||
|
if (error != sizeof(cmd_wr))
|
||||||
|
return -EINVAL;
|
||||||
|
|
||||||
|
error = ili251x_firmware_busy(client);
|
||||||
|
if (error)
|
||||||
|
return error;
|
||||||
|
|
||||||
|
for (fw_addr = start; fw_addr < end; fw_addr += 32) {
|
||||||
|
fw_data[0] = REG_WRITE_DATA;
|
||||||
|
memcpy(&(fw_data[1]), fwbuf + fw_addr, 32);
|
||||||
|
error = i2c_master_send(client, fw_data, 33);
|
||||||
|
if (error != sizeof(fw_data))
|
||||||
|
return error;
|
||||||
|
error = ili251x_firmware_busy(client);
|
||||||
|
if (error)
|
||||||
|
return error;
|
||||||
|
}
|
||||||
|
|
||||||
|
error = i2c_master_send(client, &cmd_crc, 1);
|
||||||
|
if (error != 1)
|
||||||
|
return -EINVAL;
|
||||||
|
|
||||||
|
error = ili251x_firmware_busy(client);
|
||||||
|
if (error)
|
||||||
|
return error;
|
||||||
|
|
||||||
|
error = priv->chip->read_reg(client, REG_READ_DATA_CRC,
|
||||||
|
&crcrb, sizeof(crcrb));
|
||||||
|
if (error)
|
||||||
|
return error;
|
||||||
|
|
||||||
|
/* Check CRC readback */
|
||||||
|
if ((crcrb[0] != (crc & 0xff)) || crcrb[1] != ((crc >> 8) & 0xff))
|
||||||
|
return -EINVAL;
|
||||||
|
|
||||||
|
return 0;
|
||||||
|
}
|
||||||
|
|
||||||
|
static int ili251x_firmware_reset(struct i2c_client *client)
|
||||||
|
{
|
||||||
|
u8 cmd_reset[2] = { 0xf2, 0x01 };
|
||||||
|
int error;
|
||||||
|
|
||||||
|
error = i2c_master_send(client, cmd_reset, sizeof(cmd_reset));
|
||||||
|
if (error != sizeof(cmd_reset))
|
||||||
|
return -EINVAL;
|
||||||
|
|
||||||
|
return ili251x_firmware_busy(client);
|
||||||
|
}
|
||||||
|
|
||||||
|
static void ili251x_hardware_reset(struct device *dev)
|
||||||
|
{
|
||||||
|
struct i2c_client *client = to_i2c_client(dev);
|
||||||
|
struct ili210x *priv = i2c_get_clientdata(client);
|
||||||
|
|
||||||
|
/* Reset the controller */
|
||||||
|
gpiod_set_value_cansleep(priv->reset_gpio, 1);
|
||||||
|
usleep_range(10000, 15000);
|
||||||
|
gpiod_set_value_cansleep(priv->reset_gpio, 0);
|
||||||
|
msleep(300);
|
||||||
|
}
|
||||||
|
|
||||||
|
static ssize_t ili210x_firmware_update_store(struct device *dev,
|
||||||
|
struct device_attribute *attr,
|
||||||
|
const char *buf, size_t count)
|
||||||
|
{
|
||||||
|
struct i2c_client *client = to_i2c_client(dev);
|
||||||
|
const char *fwname = ILI251X_FW_FILENAME;
|
||||||
|
const struct firmware *fw;
|
||||||
|
u16 ac_end, df_end;
|
||||||
|
u8 *fwbuf;
|
||||||
|
int error;
|
||||||
|
int i;
|
||||||
|
|
||||||
|
error = request_ihex_firmware(&fw, fwname, dev);
|
||||||
|
if (error) {
|
||||||
|
dev_err(dev, "Failed to request firmware %s, error=%d\n",
|
||||||
|
fwname, error);
|
||||||
|
return error;
|
||||||
|
}
|
||||||
|
|
||||||
|
error = ili251x_firmware_to_buffer(fw, &fwbuf, &ac_end, &df_end);
|
||||||
|
release_firmware(fw);
|
||||||
|
if (error)
|
||||||
|
return error;
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Disable touchscreen IRQ, so that we would not get spurious touch
|
||||||
|
* interrupt during firmware update, and so that the IRQ handler won't
|
||||||
|
* trigger and interfere with the firmware update. There is no bit in
|
||||||
|
* the touch controller to disable the IRQs during update, so we have
|
||||||
|
* to do it this way here.
|
||||||
|
*/
|
||||||
|
disable_irq(client->irq);
|
||||||
|
|
||||||
|
dev_dbg(dev, "Firmware update started, firmware=%s\n", fwname);
|
||||||
|
|
||||||
|
ili251x_hardware_reset(dev);
|
||||||
|
|
||||||
|
error = ili251x_firmware_reset(client);
|
||||||
|
if (error)
|
||||||
|
goto exit;
|
||||||
|
|
||||||
|
/* This may not succeed on first try, so re-try a few times. */
|
||||||
|
for (i = 0; i < 5; i++) {
|
||||||
|
error = ili251x_switch_ic_mode(client, REG_SET_MODE_BL);
|
||||||
|
if (!error)
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
|
||||||
|
if (error)
|
||||||
|
goto exit;
|
||||||
|
|
||||||
|
dev_dbg(dev, "IC is now in BootLoader mode\n");
|
||||||
|
|
||||||
|
msleep(200); /* The bootloader seems to need some time too. */
|
||||||
|
|
||||||
|
error = ili251x_firmware_write_to_ic(dev, fwbuf, 0xf000, df_end, 1);
|
||||||
|
if (error) {
|
||||||
|
dev_err(dev, "DF firmware update failed, error=%d\n", error);
|
||||||
|
goto exit;
|
||||||
|
}
|
||||||
|
|
||||||
|
dev_dbg(dev, "DataFlash firmware written\n");
|
||||||
|
|
||||||
|
error = ili251x_firmware_write_to_ic(dev, fwbuf, 0x2000, ac_end, 0);
|
||||||
|
if (error) {
|
||||||
|
dev_err(dev, "AC firmware update failed, error=%d\n", error);
|
||||||
|
goto exit;
|
||||||
|
}
|
||||||
|
|
||||||
|
dev_dbg(dev, "Application firmware written\n");
|
||||||
|
|
||||||
|
/* This may not succeed on first try, so re-try a few times. */
|
||||||
|
for (i = 0; i < 5; i++) {
|
||||||
|
error = ili251x_switch_ic_mode(client, REG_SET_MODE_AP);
|
||||||
|
if (!error)
|
||||||
|
break;
|
||||||
|
}
|
||||||
|
|
||||||
|
if (error)
|
||||||
|
goto exit;
|
||||||
|
|
||||||
|
dev_dbg(dev, "IC is now in Application mode\n");
|
||||||
|
|
||||||
|
error = ili251x_firmware_update_cached_state(dev);
|
||||||
|
if (error)
|
||||||
|
goto exit;
|
||||||
|
|
||||||
|
error = count;
|
||||||
|
|
||||||
|
exit:
|
||||||
|
ili251x_hardware_reset(dev);
|
||||||
|
dev_dbg(dev, "Firmware update ended, error=%i\n", error);
|
||||||
|
enable_irq(client->irq);
|
||||||
|
kfree(fwbuf);
|
||||||
|
return error;
|
||||||
|
}
|
||||||
|
|
||||||
|
static DEVICE_ATTR(firmware_update, 0200, NULL, ili210x_firmware_update_store);
|
||||||
|
|
||||||
static struct attribute *ili210x_attributes[] = {
|
static struct attribute *ili210x_attributes[] = {
|
||||||
&dev_attr_calibrate.attr,
|
&dev_attr_calibrate.attr,
|
||||||
|
&dev_attr_firmware_update.attr,
|
||||||
&dev_attr_firmware_version.attr,
|
&dev_attr_firmware_version.attr,
|
||||||
&dev_attr_kernel_version.attr,
|
&dev_attr_kernel_version.attr,
|
||||||
&dev_attr_protocol_version.attr,
|
&dev_attr_protocol_version.attr,
|
||||||
|
|
Загрузка…
Ссылка в новой задаче