diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
index 532b1d440abc..6cd3525d0e09 100644
--- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
@@ -46,13 +46,14 @@ Required Properties:
       - if CIU clock divider value is 0 (that is divide by 1), both tx and rx
         phase shift clocks should be 0.
 
-Required properties for a slot:
+Required properties for a slot (Deprecated - Recommend to use one slot per host):
 
 * gpios: specifies a list of gpios used for command, clock and data bus. The
   first gpio is the command line and the second gpio is the clock line. The
   rest of the gpios (depending on the bus-width property) are the data lines in
   no particular order. The format of the gpio specifier depends on the gpio
   controller.
+(Deprecated - Refer to Documentation/devicetree/binding/pinctrl/samsung-pinctrl.txt)
 
 Example:
 
@@ -69,21 +70,13 @@ Example:
 
 	dwmmc0@12200000 {
 		num-slots = <1>;
-		supports-highspeed;
+		cap-mmc-highspeed;
+		cap-sd-highspeed;
 		broken-cd;
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
 		samsung,dw-mshc-ciu-div = <3>;
 		samsung,dw-mshc-sdr-timing = <2 3>;
 		samsung,dw-mshc-ddr-timing = <1 2>;
-
-		slot@0 {
-			reg = <0>;
-			bus-width = <8>;
-			gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
-				<&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
-				<&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>,
-				<&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
-				<&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>;
-		};
+		bus-width = <8>;
 	};
diff --git a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt
index e5bc49f764d1..3b3544931437 100644
--- a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt
@@ -34,13 +34,11 @@ Example:
 		num-slots = <1>;
 		vmmc-supply = <&ldo12>;
 		fifo-depth = <0x100>;
-		supports-highspeed;
 		pinctrl-names = "default";
 		pinctrl-0 = <&sd_pmx_pins &sd_cfg_func1 &sd_cfg_func2>;
-		slot@0 {
-			reg = <0>;
-			bus-width = <4>;
-			disable-wp;
-			cd-gpios = <&gpio10 3 0>;
-		};
+		bus-width = <4>;
+		disable-wp;
+		cd-gpios = <&gpio10 3 0>;
+		cap-mmc-highspeed;
+		cap-sd-highspeed;
 	};
diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
index 2d4a7258a10d..346c6095a615 100644
--- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
@@ -67,7 +67,8 @@ Optional properties:
 * card-detect-delay: Delay in milli-seconds before detecting card after card
   insert event. The default value is 0.
 
-* supports-highspeed: Enables support for high speed cards (up to 50MHz)
+* supports-highspeed (DEPRECATED): Enables support for high speed cards (up to 50MHz)
+			   (use "cap-mmc-highspeed" or "cap-sd-highspeed" instead)
 
 * broken-cd: as documented in mmc core bindings.
 
@@ -98,14 +99,11 @@ board specific portions as listed below.
 		clock-frequency = <400000000>;
 		clock-freq-min-max = <400000 200000000>;
 		num-slots = <1>;
-		supports-highspeed;
 		broken-cd;
 		fifo-depth = <0x80>;
 		card-detect-delay = <200>;
 		vmmc-supply = <&buck8>;
-
-		slot@0 {
-			reg = <0>;
-			bus-width = <8>;
-		};
+		bus-width = <8>;
+		cap-mmc-highspeed;
+		cap-sd-highspeed;
 	};